Search Results

Search found 4489 results on 180 pages for 'black cobra'.

Page 98/180 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

  • Can I run my MacBook in clamshell mode without being connected to power?

    - by kch
    Hi, At home, I run my MacBook in clamshell mode (closed lid, external display). This works fine when you're connected to the power adapter, but it doesn't work when running on battery. That's how it's supposed to be and Apple has some kb entry on the issue. But it's also lame. You can prevent the machine from sleeping when closed by running InsomniaX, but then it'll assume the builtin display is still active, so you end up with a two-display setup when you really only want the external. This is obviously less than ideal. So, is there any work around, hack, utility, black magic that I can use to make it run in clamshell mode while strictly on battery power? Also, bonus points for a solution that makes the AC status not affect the machine state at all. (Like, you know, it does normally, when not in clamshell.)

    Read the article

  • My MacBook Pro (2011) is dead

    - by Dave
    I connected my Sony digital camera with the MacBook and the screen turned black. I wonder why because the Sony camera was not on at the time and technically could not be accessed. So I thought it might be temporary and I turned on my camera. Well, it did not work, but my MacBook Pro has been dead since then. It will not turn on - when I hold the power button for five seconds, nothing happens. When I connect the charger cable, the green light is very dim and blinks a little (with about 20% illumination). I wonder what the problem is. I have to call Apple Care, but just so that I know, what could be wrong? Is my MacBook permanently dead? It might be under warranty but I am not sure.

    Read the article

  • startx error no desktop manager

    - by WikiWitz
    I have Backtrack 5R2 KDE. I started recovery mode and did a failsafe xorg configuration. After that, I cannot load the KDE manager when I enter the startx command after logging in. Whenever I do a startx command (as root), the result resembles the following: This is not the actual output (I just drew this with MS paint because I cannot do a printscreen). The screen is just black with the icon in the upper left corner. The other pop-up menu appears when left-clicking the mouse. I tried the cp xorg.conf.failsafe xorg.conf advice from other websites with no luck. I have also tried the 'reconfigure option(s)' form the recovery mode with no success.

    Read the article

  • Why do I have no TTY on a basic Ubuntu 9.10 server install?

    - by pr1001
    I have reinstalled Ubuntu 9.10 Server several times on a bog standard 1RU server and each time I finish the install and reboot I see GRUB run and am then presented with a black screen. The machine is running just fine, as I am able to SSH in, but I can't see anything on the attached monitor. I have a simple LCD screen connected via VGA and a signal is apparently being output to it, as it doesn't go asleep. Looking at /var/log/syslog I see: Mar 24 14:57:44 bridge5 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] However, I later see: Mar 24 14:57:44 bridge5 kernel: [ 0.001368] console [tty0] enabled Any thoughts? Thanks!

    Read the article

  • I hyperlinked a cell in excel 2003, formula issues?

    - by joseinsomniac
    I have a budget spreadsheet using excel 2003. I have My deposit, then all of my bills, the total, then a cell that has the difference(between the amount of deposit and the total of the bills). The difference cell numbers turn red when I dont have enough money (deposit vs bill total). I hyperlinked the difference cell to a checkbook register spreadsheet so I can track where all my extra money went(reconsile receipts daily). When hyperlinked the numbers are blue. I need the numbers to stay black(when above 0.00) and stay red (when the numbers are below 0.00) and not change after the link has been clicked on. Also if the link has not been clicked on, and the numbers are red, the font is smaller, even though the toolbar shows the font size hasnt changed. After I click on it and go back to the budget sheet, its the size it should be. Any Ideas? Thanks!

    Read the article

  • Trouble with external monitor under Windows 7 on MacBook Pro Boot Camp

    - by Colm
    I'm running Windows 7 32-bit on a mid-2010 15" MacBook Pro Intel Core i5 under Boot Camp. I've had trouble getting it to work with my second display and searching Google for an appropriate answer has failed me. I'm on the latest version of Boot Camp - 3.2 - and have updated the drivers for the NVIDIA GeForce GT 330M. The monitor is connected via a VGA cable, and is a Dell ST2410. The monitor is recognised by Windows, which knows it's a Dell and its resolution. The desktop should be extended onto the second monitor - however nothing is showing. It remains black, though it doesn't show a lack of signal coming through which I would have expected. Any ideas what's wrong?

    Read the article

  • What's wrong with this jQuery? It isn't working as intended

    - by Doug Smith
    Using cookies, I want it to remember the colour layout of the page. (So, if they set the gallery one color and the body background another color, it will save that on refresh. But it doesn't seem to be working. jQuery: $(document).ready(function() { if (verifier == 1) { $('body').css('background', $.cookie('test_cookie')); } if (verifier == 2) { $('#gallery').css('background', $.cookie('test_cookie')); } if (verifier == 3) { $('body').css('background', $.cookie('test_cookie')); $('#gallery').css('background', $.cookie('test_cookie')); } $('#set_cookie').click(function() { var color = $('#set_cookie').val(); $.cookie('test_cookie', color); }); $('#set_page').click(function() { $('body').css('background', $.cookie('test_cookie')); var verifier = 1; }); $('#set_gallery').click(function() { $('#gallery').css('background', $.cookie('test_cookie')); var verifier = 2; }); $('#set_both').click(function() { $('body').css('background', $.cookie('test_cookie')); $('#gallery').css('background', $.cookie('test_cookie')); var verifier = 3; }); }); HTML: <p>Please select a background color for either the page's background, the gallery's background, or both.</p> <select id="set_cookie"> <option value="#1d375a" selected="selected">Default</option> <option value="black">Black</option> <option value="blue">Blue</option> <option value="brown">Brown</option> <option value="darkblue">Dark Blue</option> <option value="darkgreen">Dark Green</option> <option value="darkred">Dark Red</option> <option value="fuchsia">Fuchsia</option> <option value="green">Green</option> <option value="grey">Grey</option> <option value="#d3d3d3">Light Grey</option> <option value="#32cd32">Lime Green</option> <option value="#f8b040">Macaroni</option> <option value="#ff7300">Orange</option> <option value="pink">Pink</option> <option value="purple">Purple</option> <option value="red">Red</option> <option value="#0fcce0">Turquoise</option> <option value="white">White</option> <option value="yellow">Yellow</option> </select> <input type="button" id="set_page" value="Page's Background" /><input type="button" id="set_gallery" value="Gallery's Background" /><input type="button" id="set_both" value="Both" /> </div> </div> </body> </html> Thanks so much for the help, I appreciate it. jsFiddle: http://jsfiddle.net/hL6Ye/

    Read the article

  • Illustrator "Save for Web & Devices" returning crappy, pixelated images

    - by Tory Waterman
    I'm trying to create a nice title for my webpage... a big white title to sit on a black background. I'm using Illustrator to do so. When I create it, it looks nice, but when I hit "save for web & devices", it comes out looking like a pixelated piece of crap on the site. Is there some setting I need to change to make Illustrator save a higher resolution image? Thanks EDIT I understand, from looking at some other posts, that this may be a result of "posterization" or "dither", but this is only a plain white image so I don't how this results in a colors problem. (I could be completely misinterpreting these terms) EDIT Figured version might be important... I'm using CS5.1

    Read the article

  • Ubuntu 9.10 freezes when HDMI port is connected

    - by Felipe Hummel
    Hi, I have a Sony Vaio FW350 with a HDMI output. I'm trying to use it under Ubuntu 9.10 with a LG LCD monitor 21,5'. I've tried two approaches: Boot the laptop with the HDMI cable connected and monitor turned on. Result: LCD Monitor keeps turned on but the whole screen is black and Ubuntu do not seem to be initializing. Boot Ubuntu until the end. I then connect the HDMI cable into the Laptop. The mouse and the whole system freezes. In both cases the only way to turn off the laptop is holding the power button. I've looked around the internet for similar problems, but only found workarounds for the same problem with VGA input, not HDMI. I also tried to use metacity before connecting the cable, but still got the same result. Any hints?

    Read the article

  • Windows Boot disc to save files?

    - by acidzombie24
    Somehow after updating my legit windows 7 OS with no pirated or mod software on my PC i was welcome to a black screen. I popped in my ghost disc and copied the files i need to an external HD. IIRC windows 7 disc can do that too. Problem with the way i did it on ghost was it excepted me to select 1 file (an HD disc image) so i couldnt select multiple folders to move. Also when i did move i had no idea if it finished or how long it would take. My linux live cd couldnt access the HD. Anyways, is there a disc i can use to easily copy files from my laptop to my external HD? I think ghost, windows 7 and windows server all allow me but is there one that is better suited to copy files?

    Read the article

  • How does one go about fixing a pixelation issue?

    - by Tyler
    I've been having a lot of trouble with pixelation and also in-game display driver crashes. At first I thought the problem may have been my graphics card (Sapphire 5750) but I have RMA'd it three times and I'm still having trouble. So what I think it might be is my PSU, its 650Watt but its made by Azza so it was cheap and not made by a necessarily good company. Or maybe it could be the CPU (AMD Phenom Black Edition 3.4Ghz) It runs hot (60C) but it passes Everest's test. Someone told me it could be the memory (8GB DDR3) but I don't really see how RAM has anything to do with my problem. So what are some of you suggestions? Here is a video a made awhile ago of what is happening. http://www.metacafe.com/watch/4392213/ati_radeon_5750/ That was just a stress test most games tend to just freeze and crash or lock my system up.

    Read the article

  • X58 RAID 10 - Am I forced to use Sata2?

    - by Avi
    I'm building a new dev computer. It will be running a few VMWare Worksation virtual machines. I was advised on Serverfault to use Raid10 for performance. Raid 10 uses 4 disks. I contacted my supplier who suggested a gigabyte X58A motherboard and 4 Western Digital Caviar black 6Gb/s disks. I have checked the spec for the X58A board, however, and it says: SATA 3Gb/s: RAID 0, RAID 1, RAID 5, and RAID 10 SATA 6Gb/s: RAID 0, and RAID 1. I'm losing half the bandwidth because I'm forced to use SATA2! What should I do?

    Read the article

  • Stop UAC/Secure Desktop from dimming the screen

    - by Florian
    I like the concepts of UAC and the "Secure Desktop" in Windows 7, but I don't like the dimming of the Secure Desktop to prompt for Admin credentials (or OK button to get clicked). However, dimming goes so far that my monitor regularly goes into PowerSaver mode, which is annoying (as it takes another 10 seconds for it to wake up), and might harm the monitor: two weeks after switching from XP to Windows 7, my 30" monitor stayed black and it had to get replaced. The web is full of tips how to turn off dimming, but that will always also turn off the "Secure Desktop". Is there a way to present the Secure Desktop without dimming? Or with a different visual effect to show that it is the Secure Desktop? EDIT: To clarify, I'm not looking for a way to disable dimming by disabling Secure Desktop (as is done by lowering the UAC level). I want to keep both UAC and Secure Desktop.

    Read the article

  • Create intentional border with xrandr

    - by benizi
    Is there a way to tell xrandr "this space intentionally left blank"? I have a laptop that drives its internal display at 1920x1080, but the external monitor I'm using, due to its different aspect ratio, doesn't have that mode. It runs at 1920x1200. So, the basic setup: xrandr \ --output LVDS-1 --mode 1920x1080 \ --output DP-1 --mode 1920x1200 --same-as LVDS-1 [not to scale:] +-----------------------------------+ ¦ ¦ ¦ ¦ (laptop) ¦ (external) ¦ ¦ (LVDS-1) ¦ (DP-1) ¦ ¦ ¦ ¦ ¦ ¦ ¦ +-----------------¦ ¦ (blank...) ¦ ¦ +-----------------+ How can I specify that the 1920x120-sized region below LVDS-1 should be displayed as a black bar that can't be accessed by mouse on DP-1? I tried just coping with --panning 1920x1200+0+0/1920x1080+0+0/0/0/0/120, but I found the screen movement to be very annoying. Update: I found a workaround. (Update 2: changed it to an answer, per suggestion -- workaround doesn't answer the underlying question of leaving space blank.)

    Read the article

  • Best DSL hardware for ADSL Troubleshooting

    - by Jeff Sacksteder
    I have a situation where I need to make the best of a bad DSL situation. The CPE is a black box with no access to DSL diagnostics. My plan is to get some sort of DSL hardware that exposes link-layer state and gives me knobs to tweak. I'd like to be able to mitigate bufferbloat as much as I can while I'm at it. The obvious choice would seem to be a Sangoma card in a linux system. I have no way of knowing if that will do anything for me without testing it, however. I have no other access to WAN troubleshooting equipment. Are there any other options avail to me as a consumer?

    Read the article

  • DVI problem with LG L204WT

    - by Holgerwa
    I have a LG L204WT which has VGA and DVI connectors. Until recently, I have used the monitor via VGA, but now I have upgraded the graphics board and switched to DVI. The problem is that each time after the computer starts, the monitor either doesn't show anything (black screen, but doesn't go into standby) or the picture is distorted. I then switch the monitor off and on several times, and at some point it starts correctly and then I can work as usual. This only happens on startup. It is one out of 3 monitors, the other two work fine. It seems to me as if the monitor is not able to synchronize on the DVI signal and either shows a distorted picture or nothing at all. There are no settings in the monitor setup that would change anything. What could be the problem?

    Read the article

  • Computer only booting after POWER ON/OFF 10 times or more?

    - by Jan Gressmann
    Hi fellow geeks, recently my computer started to behave like an old car and won't start up anymore unless I flip the power switch repeatedly. What happens when I power it on: CPU fans spins briefly and very slowly, then it stops Same with GPU fan No BIOS beeps or HDD activity Screen stays black After turning it on and off for like 10 times, it'll eventually boot like normal and run smooth without any problems what-so-ever. But I'm worried it might eventually die completely. Anyone know the most common cause of this? Maybe I should just leave the computer powered on? :)

    Read the article

  • HDD not detected whenever first power on (detected at BIOS level)

    - by Alvin Lim
    I am using Asus P8H61-M LX Motherboard with latest version of BIOS: 4401 One SATA-3 Western Digital Black Series 1.5TB is attached to SATA port 0 A Samsung 22x DVDRW SATA drive attached to SATA Port 1. ps/2 Logitech mouse and keyboard. CPU is i3 with DDR3 8Gb RAM. no other devices are installed. My problem is that when I turn on the computer, the WD HDD is not detected. ie cannot be booted. I have to press ctrl+alt+del in order to get it detected. I'd used the WD data lifeguard software to scan the HDD, the smart status is OK, the surface scan does not show any error at all. Where did I do wrong? Any advice is greatly appreciated.

    Read the article

  • plugging in a 3.3V 50pin laptop HDD to USB?

    - by barlop
    I have a 50pin laptop hard drive. 1.8" wide. This 50pin connector concerns me.. Even if I get an adaptor, How can I know which side of the connector takes the power? I don't want to plug it in the wrong way. And I don't have n adaptor.. Could people link me to adaptors too. but main question is, which side to plug it in when I get the adaptor. I want to be sure. I do not want to blow the hdd. For the 3.3V I have a plan. Connecting green and black and using the orange cable(3.3v) to feed power. I am not too worried about that bit. But as I said.. Main thing is I want to know which side is 3.3V hard drive is MK6006GAH

    Read the article

  • How do I free some disk space so Ubuntu will boot again?

    - by Omkant
    I have installed Windows and Ubuntu side by side. I created a 10GB partition for the Ubuntu installation. During the two months I've been using Ubuntu I have installed some software. Now it's not starting. When I boot up it says that there is no diskspace so it could not be started . What can i do now? When I boot up all I get is a black screen terminal with a $. Please help me with a command to uninstall some programs and start using Ubuntu or any other way to get rid of this message.

    Read the article

  • Why is Windows 7 so slow to log-on when my Wireless USB dongle is plugged in?

    - by Sam
    I'm using an Edimax Wireless USB dongle (model EW-7711UTN) on Windows 7 64-bit. The dongle works brilliantly (it was truly plug-and-play) except for one thing. I've noticed that if the dongle is plugged in whilst I'm logging on to Windows it introduces a massive delay - after I type in my password and hit enter, Windows shows the "Welcome" screen, then the screen goes black for 2 minutes or so (with just the cursor showing) before finally displaying my desktop. If I unplug the dongle before I enter my password, Windows goes straight to my desktop. Even though the dongle didn't appear to need drivers for Windows 7, I did try downloading the latest ones from the Edimax website, but that made no difference.

    Read the article

  • Windows 8 Color Settings (Window Title)

    - by xixixao
    In Windows 7, the window title's color (by default black, to see the title in the title bar fire up Windows Media Player for example) is stored in [HKEY_CURRENT_USER\Control Panel\Desktop\Colors] TitleText value. This is not the case in Windows 8, since this value is only used when using high contrast theme. It looks like noone has come up with a way to change this color yet, so my question is, where to look? What tools can I use to see dependencies, what could be the way to find this value (I rightfully hope it's not a constant in code).

    Read the article

  • Blank screen after grub menu

    - by Tim
    I just rebooted an Ubuntu Server 10.04. After choosing boot options in the grub menu, though, it just displays a black screen with the blinking white underscore in the upper-left corner. The machine has had (hardware) trouble with networking before, but the problem remains after 10 minutes, so I don't think it's the problem now. Booting into recovery mode or using earlier kernels yields the same problem. This also happens if I boot from another hard-drive. I haven't yet tried to boot from CD as the machine lacks a CD reader. How should I diagnose the problem? Update: My boot options are: recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set 567[redacted] linux /boot/vmlinuz-2.6.32-29-generic root=UUID=567[redacted] ro quiet splash initrd /boot/initrd.img-2.6.32-29-generic Update: Also, I cannot access the virtual terminals (ctrl+alt+Fn).

    Read the article

  • ATI Radeon 4350 lower resolutions do not fill screen in Windows 7

    - by rlandster
    I have a new Windows 7 64-bit machine with an ATI HD4350 card. The card is connected via VGA (DSUB) to a SyncMaster 205 BW LCD monitor. If I set the resolution to 1680x1050 the LCD screen is completely filled and everything looks fine. But, if I try to set the resolution to 1280x768 (my preferred resolution) only about 2/3 of the monitor screen is used. There are large black bars above and below the image (but not on the sides). I have successfully used this monitor at the 1280x768 resolution for many years without this problem (albeit in Windows XP and a different video card). Can anyone suggest how I can get adjust things so that the entire screen is used at the 1280x768 resolution?

    Read the article

  • Ubuntu doesn't start and I can't login [migrated]

    - by Meph00
    My ubuntu 13.04 doesn't boot anymore. Eternal black screen. If I press ALT+CTRL+F1 I see that it's stucked on "Checking battery state [OK]." I'd like to try to go with sudo apt-get install gdm but I can't login on terminal tty2, tty3 etc. They correctly ask for my nickname, then they make me wait a lot, ask for password and make me wait again. After a lot of time (... a lot) the best I could achieve was visualizing "Documentantion https://help.ubuntu.com". I can never reach the point where I can give commands. Plus, during the long pauses, every 2 minutes it gives a messagge like this: INFO: task XXX blocked for more than 120 seconds. Any suggestion? Sorry for my bad english and thanks everyone for the attention.

    Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >