mup sys - Page 98 - Developer IT

Increase samba space on open suse 12.1

- by Kapil Sharma

I know linux basics but not an expert. IT guy left the job here and there is some time before new hire. So sorry if question is very basic. We have local testing server based on Open SUSE 12.1, which also act as shared drive between dev/mgmt team here and using Samba for that. Now we are running out of space on samba, even though server's 2*1TB harddisk is nearly 90% free. My question is, what is limiting Samba and how can I increase its limit? We need around at least 500 GB as shared drive but currently its just 25 GB. I don't need step by step answer, just a link to any helpful article would be sufficient. Probably I'm putting wrong keywords in google so not getting any helpful link. EDIT: Output of commands in the first comment. All commands were run as root user df -h (getting error with df -ht) Filesystem Size Used Avail Use% Mounted on rootfs 30G 5.1G 23G 19% / devtmpfs 2.0G 36K 2.0G 1% /dev tmpfs 2.0G 1.1M 2.0G 1% /dev/shm tmpfs 2.0G 676K 2.0G 1% /run /dev/sda2 30G 5.1G 23G 19% / tmpfs 2.0G 0 2.0G 0% /sys/fs/cgroup tmpfs 2.0G 676K 2.0G 1% /var/run tmpfs 2.0G 0 2.0G 0% /media tmpfs 2.0G 676K 2.0G 1% /var/lock /dev/sda3 36G 31G 3.3G 91% /home fdisk -l /dev/[hmsv]d* Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x2d4a2d49 Device Boot Start End Blocks Id System /dev/sda1 2048 16771071 8384512 82 Linux swap / Solaris /dev/sda2 * 16771072 79681535 31455232 83 Linux /dev/sda3 79681536 156301311 38309888 83 Linux Disk /dev/sda1: 8585 MB, 8585740288 bytes 255 heads, 63 sectors/track, 1043 cylinders, total 16769024 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 32.2 GB, 32210157568 bytes 255 heads, 63 sectors/track, 3915 cylinders, total 62910464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System Disk /dev/sda3: 39.2 GB, 39229325312 bytes 255 heads, 63 sectors/track, 4769 cylinders, total 76619776 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda3 doesn't contain a valid partition table vgs No volume groups found lvs No volume groups found output of vi /etc/samba/smb.conf # smb.conf is the main Samba configuration file. You find a full commented # version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the # samba-doc package is installed. # Date: 2011-11-02 [global] workgroup = WORKGROUP passdb backend = tdbsam printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User include = /etc/samba/dhcp.conf logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes [homes] comment = Home Directories valid users = %S, %D%w%S browseable = No read only = No inherit acls = Yes [profiles] comment = Network Profiles Service path = %H read only = No store dos attributes = Yes create mask = 0600 directory mask = 0700 [users] comment = All users path = /home read only = No inherit acls = Yes veto files = /aquota.user/groups/shares/ [groups] comment = All groups path = /home/groups read only = No inherit acls = Yes [printers] comment = All Printers path = /var/tmp printable = Yes create mask = 0600 browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/drivers write list = @ntadmin root force group = ntadmin create mask = 0664 directory mask = 0775 [allusers] comment = All Users path = /home/shares/allusers valid users = @users force group = users create mask = 0660 directory mask = 0771 writable = yes

Read the article

Determining cause of high NFS/IO utilization without iotop

- by Matt

I have a server that is doing an NFSv4 export for user's home directories. There are roughly 25 users (mostly developers/analysts) and about 40 servers mounting the home directory export. Performance is miserable, with users often seeing multi-second lags for simple commands (like ls, or writing a small text file). Sometimes the home directory mount completely hangs for minutes, with users getting "permission denied" errors. The hardware is a Dell R510 with dual E5620 CPUs and 8 GB RAM. There are eight 15k 2.5” 600 GB drives (Seagate ST3600057SS) configured in hardware RAID-6 with a single hot spare. RAID controller is a Dell PERC H700 w/512MB cache (Linux sees this as a LSI MegaSAS 9260). OS is CentOS 5.6, home directory partition is ext3, with options “rw,data=journal,usrquota”. I have the HW RAID configured to present two virtual disks to the OS: /dev/sda for the OS (boot, root and swap partitions), and /dev/sdb for the home directories. What I find curious, and suspicious, is that the sda device often has very high utilization, even though it only contains the OS. I would expect this virtual drive to be idle almost all the time. The system is not swapping, according to "free" and "vmstat". Why would there be major load on this device? Here is a 30-second snapshot from iostat: Time: 09:37:28 AM Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 44.09 0.03 107.76 0.13 607.40 11.27 0.89 8.27 7.27 78.35 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 44.09 0.03 107.76 0.13 607.40 11.27 0.89 8.27 7.27 78.35 sdb 0.00 2616.53 0.67 157.88 2.80 11098.83 140.04 8.57 54.08 4.21 66.68 sdb1 0.00 2616.53 0.67 157.88 2.80 11098.83 140.04 8.57 54.08 4.21 66.68 dm-0 0.00 0.00 0.03 151.82 0.13 607.26 8.00 1.25 8.23 5.16 78.35 dm-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-2 0.00 0.00 0.67 2774.84 2.80 11099.37 8.00 474.30 170.89 0.24 66.84 dm-3 0.00 0.00 0.67 2774.84 2.80 11099.37 8.00 474.30 170.89 0.24 66.84 Looks like iotop is the ideal tool to use to sniff out these kinds of issues. But I'm on CentOS 5.6, which doesn't have a new enough kernel to support that program. I looked at Determining which process is causing heavy disk I/O?, and besides iotop, one of the suggestions said to do a "echo 1 /proc/sys/vm/block_dump". I did that (after directing kernel messages to tempfs). In about 13 minutes I had about 700k reads or writes, roughly half from kjournald and the other half from nfsd: # egrep " kernel: .*(READ|WRITE)" messages | wc -l 768439 # egrep " kernel: kjournald.*(READ|WRITE)" messages | wc -l 403615 # egrep " kernel: nfsd.*(READ|WRITE)" messages | wc -l 314028 For what it's worth, for the last hour, utilization has constantly been over 90% for the home directory drive. My 30-second iostat keeps showing output like this: Time: 09:36:30 PM Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 6.46 0.20 11.33 0.80 71.71 12.58 0.24 20.53 14.37 16.56 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 6.46 0.20 11.33 0.80 71.71 12.58 0.24 20.53 14.37 16.56 sdb 137.29 7.00 549.92 3.80 22817.19 43.19 82.57 3.02 5.45 1.74 96.32 sdb1 137.29 7.00 549.92 3.80 22817.19 43.19 82.57 3.02 5.45 1.74 96.32 dm-0 0.00 0.00 0.20 17.76 0.80 71.04 8.00 0.38 21.21 9.22 16.57 dm-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-2 0.00 0.00 687.47 10.80 22817.19 43.19 65.48 4.62 6.61 1.43 99.81 dm-3 0.00 0.00 687.47 10.80 22817.19 43.19 65.48 4.62 6.61 1.43 99.82

Read the article

xrandr shows two displays (LVDS1), but how can I use VGA1 only?

- by Tom Fishman

We're running Ubuntu 11 on this hardware: Foxconn R20-D2 Intel Atom D510 Intel NM10 Intel GMA 3150 Barebone There is no integrated display (it is a barebone box). I connected an external VGA to it. However xrandr shows two displays: Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 519mm x 324mm 1920x1200 60.0 + 1600x1200 60.0 1680x1050 60.0 1280x1024 76.0 75.0 72.0 60.0 1440x900 75.0 59.9 1152x864 75.0 1024x768 75.1 70.1 60.0* 832x624 74.6 800x600 72.2 75.0 60.3 640x480 72.8 75.0 66.7 60.0 720x400 70.1 But I don't have two displays. How can I get rid of LVDS1 and use only VGA1? The direct result is that I'm seeing a 1024x768 resolution on my VGA display, because the OS is using "mirror" mode which uses the lower resolution of the two. Turning off the mirror is not a solution. I want to fix it. Related logs: ... [ 20.019] (II) intel(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 20.019] (==) intel(0): Depth 24, (--) framebuffer bpp 32 [ 20.019] (==) intel(0): RGB weight 888 [ 20.019] (==) intel(0): Default visual is TrueColor [ 20.019] (II) intel(0): Integrated Graphics Chipset: Intel(R) Pineview G [ 20.019] (--) intel(0): Chipset: "Pineview G" [ 20.019] (**) intel(0): Relaxed fencing enabled [ 20.019] (**) intel(0): Wait on SwapBuffers? enabled [ 20.019] (**) intel(0): Triple buffering? enabled [ 20.019] (**) intel(0): Framebuffer tiled [ 20.019] (**) intel(0): Pixmaps tiled [ 20.020] (**) intel(0): 3D buffers tiled [ 20.020] (**) intel(0): SwapBuffers wait enabled [ 20.020] (==) intel(0): video overlay key set to 0x101fe [ 20.020] (II) intel(0): Output LVDS1 has no monitor section [ 20.020] (II) intel(0): found backlight control interface /sys/class/backlight/intel_backlight [ 20.080] (II) intel(0): Output VGA1 has no monitor section [ 20.080] (II) intel(0): EDID for output LVDS1 [ 20.081] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported) ... [ 20.082] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported) [ 20.082] (II) intel(0): Printing probed modes for output LVDS1 [ 20.082] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) [ 20.082] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) [ 20.082] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz) [ 20.082] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) [ 20.149] (II) intel(0): EDID for output VGA1 [ 20.149] (II) intel(0): Manufacturer: BNQ Model: 771b Serial#: 6595 [ 20.149] (II) intel(0): Year: 2008 Week: 16 [ 20.149] (II) intel(0): EDID Version: 1.3 [ 20.149] (II) intel(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V ... [ 20.152] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) [ 20.152] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz) [ 20.152] (II) intel(0): Output LVDS1 connected [ 20.152] (II) intel(0): Output VGA1 connected [ 20.152] (II) intel(0): Using exact sizes for initial modes [ 20.152] (II) intel(0): Output LVDS1 using initial mode 1024x768 [ 20.152] (II) intel(0): Output VGA1 using initial mode 1024x768 [ 20.152] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. ...

Read the article

Where's the Swap File/Partition?

- by chrisbunney

I'm investigating the virtual memory configuration of a Debian based Amazon EC2 instance, and as my background isn't in system admin, I'm slightly confused by what I'm seeing. We're using MongoDB, and the monitoring server we have indicates that the Mongo process is using about 20GB of swap space, however I can't figure out where this is located on the server. As far as I can tell from using the various suggested methods from Google, there is either a much smaller amount, or none at all. top indicates that there is 1.8GB of swap memory: top - 15:35:21 up 6 days, 3:23, 1 user, load average: 1.60, 1.43, 1.37 Tasks: 47 total, 2 running, 45 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 1.3%sy, 0.0%ni, 14.7%id, 83.8%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 3928924k total, 2855572k used, 1073352k free, 640564k buffers Swap: 0k total, 0k used, 0k free, 1887788k cached swapon -s doesn't seem to think there's any swap space: Filename Type Size Used Priority free -m doesn't think there's any swap either: total used free shared buffers cached Mem: 3836 3663 172 0 626 2701 -/+ buffers/cache: 336 3500 Swap: 0 0 0 And neither does vmstat: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 3 0 66224 641372 2874744 0 0 21 5012 21 33 2 2 76 19 But cat /etc/fstab thinks there is a swap partition: /dev/xvda1 / ext3 defaults 1 1 /dev/xvda2 /mnt ext3 defaults 0 0 /dev/xvda3 swap swap defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 However df -k gives no indication of the xvda3 partition: Filesystem 1K-blocks Used Available Use% Mounted on /dev/xvda1 16513960 15675324 0 100% / tmpfs 1964460 8 1964452 1% /lib/init/rw udev 1914148 28 1914120 1% /dev tmpfs 1964460 4 1964456 1% /dev/shm So I really don't know what to make of this, because I appear to have a process using about 10 times more virtual memory than what might be available, and I have no idea where this virtual memory is on the system. I'm probably misinterpreting the output of the tools, so I'd be grateful if someone would be able to set me straight: What have I got wrong, what's the right interpretation, and how do you reach that interpretation? EDIT0: We use 10gen's MMS for monitoring the database, the relevant section for memory from the last data point is: "mem": { "virtual": 20749, "bits": 64, "supported": true, "mappedWithJournal": 20376, "mapped": 10188, "resident": 1219 }, This JSON is specific to the database process (I believe) rather than the system as a whole. fdisk -l /dev/xvda outputs... nothing? I tried each of the 3 xvda entries in /etc/fstab as well: root@ip:~# fdisk -l /dev/xvda1 Disk /dev/xvda1: 34.4 GB, 34359738368 bytes 255 heads, 63 sectors/track, 4177 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/xvda1 doesn't contain a valid partition table root@ip:~# fdisk -l /dev/xvda2 root@ip:~# fdisk -l /dev/xvda3 root@ip:~# Edit1: Output of cat /proc/meminfo for the sake of completeness: MemTotal: 3928924 kB MemFree: 726600 kB Buffers: 648368 kB Cached: 2216556 kB SwapCached: 0 kB Active: 1945100 kB Inactive: 994016 kB Active(anon): 60476 kB Inactive(anon): 12952 kB Active(file): 1884624 kB Inactive(file): 981064 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 387180 kB Writeback: 0 kB AnonPages: 73380 kB Mapped: 1188260 kB Shmem: 48 kB Slab: 149768 kB SReclaimable: 146076 kB SUnreclaim: 3692 kB KernelStack: 1104 kB PageTables: 16096 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 1964460 kB Committed_AS: 305572 kB VmallocTotal: 34359738367 kB VmallocUsed: 16760 kB VmallocChunk: 34359721448 kB HardwareCorrupted: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 3932160 kB DirectMap2M: 0 kB

Read the article

GNU/Linux swapping blocks system

- by Ole Tange

I have used GNU/Linux on systems from 4 MB RAM to 512 GB RAM. When they start swapping, most of the time you can still log in and kill off the offending process - you just have to be 100-1000 times more patient. On my new 32 GB system that has changed: It blocks when it starts swapping. Sometimes with full disk activity but other times with no disk activity. To examine what might be the issue I have written this program. The idea is: 1 grab 3% of the memory free right now 2 if that caused swap to increase: stop 3 keep the chunk used for 30 seconds by forking off 4 goto 1 - #!/usr/bin/perl sub freekb { my $free = `free|grep buffers/cache`; my @a=split / +/,$free; return $a[3]; } sub swapkb { my $swap = `free|grep Swap:`; my @a=split / +/,$swap; return $a[2]; } my $swap = swapkb(); my $lastswap = $swap; my $free; while($lastswap >= $swap) { print "$swap $free"; $lastswap = $swap; $swap = swapkb(); $free = freekb(); my $used_mem = "x"x(1024 * $free * 0.03); if(not fork()) { sleep 30; exit(); } } print "Swap increased $swap $lastswap\n"; Running the program forever ought to keep the system at the limit of swapping, but only grabbing a minimal amount of swap and do that very slowly (i.e. a few MB at a time at most). If I run: forever free | stdbuf -o0 timestamp > freelog I ought to see swap slowly rising every second. (forever and timestamp from https://github.com/ole-tange/tangetools). But that is not the behaviour I see: I see swap increasing in jumps and that the system is completely blocked during these jumps. Here the system is blocked for 30 seconds with the swap usage increases with 1 GB: secs 169.527 Swap: 18440184 154184 18286000 170.531 Swap: 18440184 154184 18286000 200.630 Swap: 18440184 1134240 17305944 210.259 Swap: 18440184 1076228 17363956 Blocked: 21 secs. Swap increase 2400 MB: 307.773 Swap: 18440184 581324 17858860 308.799 Swap: 18440184 597676 17842508 330.103 Swap: 18440184 2503020 15937164 331.106 Swap: 18440184 2502936 15937248 Blocked: 20 secs. Swap increase 2200 MB: 751.283 Swap: 18440184 885288 17554896 752.286 Swap: 18440184 911676 17528508 772.331 Swap: 18440184 3193532 15246652 773.333 Swap: 18440184 1404540 17035644 Blocked: 37 secs. Swap increase 2400 MB: 904.068 Swap: 18440184 613108 17827076 905.072 Swap: 18440184 610368 17829816 942.424 Swap: 18440184 3014668 15425516 942.610 Swap: 18440184 2073580 16366604 This is bad enough, but what is even worse is that the system sometimes stops responding at all - even if I wait for hours. I have the feeling it is related to the swapping issue, but I cannot tell for sure. My first idea was to tweak /proc/sys/vm/swappiness from 60 to 0 or 100, just to see if that had any effect at all. 0 did not have an effect, but 100 did cause the problem to arise less often. How can I prevent the system from blocking for such a long time? Why does it decide to swapout 1-3 GB when less than 10 MB would suffice?

Read the article

Random Slow Response

- by ARehman

We have an ASP.NET MVC 1.0 application running on Windows Server 2008 – Standard (32 –bit), Dual Core Xeon (3.0 GHz), 2 G.B R.A.M. Most of the times application renders response in 3-4 seconds, but sometimes users get very late response and delay is up to 40 seconds or more than a minute. It happens in following way: User browsed a page, idle for 5, 10 or 15 minutes, tried to browse same page or some other. Now, there is a chance that he will see late response whereas the app pool is still up and running. This can happen with any arbitrary page. We have tried followings/observations. Moved the application to stand alone web server App Pool idle shutdown time is 60 minutes. There are no abrupt shut downs/restarts. CPU or memory doesn’t spike. No delays in SQL queries. Modified App Pool setting to run in classic-mode. It didn’t help. Plugged-in custom module to log all those requests which took more than 5 seconds to complete. It didn’t pick any request of interest. Enabled ‘Failed Request Tracing’ to log all those requests which take 20 or more seconds to complete. It didn’t log anything. Event Viewer, HTTPER log, W3SVC logs or WAS logs don’t indicate anything. HTTPERR only has ‘_ _ Timer_ConnectionIdle _ _’ entries. There is not much traffic to server. This can happen also if only two users are active. Next we captured TCP/IP terrific on both a user and server end with Wireshark and below are details in brief of this slowness: Browser sends a request for ~/User/Home/ (GET Request) by setting up a receiving end point using port 'wlbs(port-2504)'. I'm not sure if this could be a problem in some way that browser didn't hand-shake with the server first and assumed that last connection is still open, whereas, I browsed the same page 4 minutes ago and didn't perform any activity with site after that. If I see the HTTPERR log, it indicates that it has ‘_ _ Timer_ConnectionIdle _ _ _’ entry for my last activity with server. Browser (I was using Chrome) waits for any response from the server, doesn’t find any then starts retransmitting the same request using same end point after incrementing wait intervals, e.g. after 8, 18, 29, 40, 62, and 92 seconds. All these GET requests were received by server as well. But, server didn’t send any packet to client. Browser didn't see any response on the end point it set up in point 1, it opened a new end point 'optiwave-lm (port-2524)', did a hand shake with the server and transmitted the same request again. Server received, processed it, and returned successful response. What happened to earlier 6-7 requests? Whether they were passed on to HTTP.SYS or not? Why Failed Request Tracing not logged anything, we didn't find any clue yet. Server served the same page successfully just 4 minutes ago. Looking forward for more suggestions/solutions. -- Thanks

Read the article

How to restore Linode to Vagrant VM?

- by Iain Elder

I'm trying to set up a Linux development environment so I can safely make changes to my website without breaking the live site. Linode hosts my live site. A simple solution would be to host my development server on Linode as well, but I want to avoid doubling my hosting costs. The cheapest way I see is to use Vagrant on my Windows workstation to host my development environment. After I attempt to restore the backup to Vagrant and reboot the VM, I can no longer ssh into the Vagrant host. It's probably because by restoring the backup I overwrite some special Vagrant configuration, but I'm not sure how to avoid that. How do I make this approach work? If my approach is fundamentally wrong, can you suggest an alternative? Creating the backup On the Linode I used these commands to create a compressed copy of the entire filesystem, while ignoring things that shouldn't be included in the backup: $ sudo rsync -ahvz --exclude={/dev/*,/proc/*,/sys/*,/tmp/*,/run/*,/mnt/*,/backup/*} /* /backup/2 $ sudo tar -czf /backup/2.gz /backup/2 The backup file is called 2.gz because this is thesecond backup. The first backup is called 1.gz. I use WinSCP to copy the backup file to my Windows workstation. Setting up the Vagrant host I need a Vagrant box that matches my Linode operating system (Ubuntu 12.04.3 LTS, kernel 3.9.3). I selected the closet match from vagrantbox.es: Ubuntu Server Precise 12.04.3 amd64 Kernel is ready for Docker (Docker not included) On my workstation I ran these commands to add the box and initialize and boot an instance: $ vagrant box add ubuntu-precise http://nitron-vagrant.s3-website-us-east-1.amazonaws.com/vagrant_ubuntu_12.04.3_amd64_virtualbox.box $ mkdir linode-test $ cd linode-test $ vagrant init ubuntu-precise $ vagrant up Now Vagrant is running a machine with SSH on port 2222. The operating system version is the same. The kernel version is 3.8.0. Sounds close enough. Restoring the backup With WinSCP I copied the backup file 2.gz to /home/vagrant/2.gz on the Vagrant box. With PuTTY I connected via ssh to my new Vagrant box: On the box move the backup to the filesystem root. $ sudo mv 2.gz / Extract the archive to the filesystem root: $ sudo tar -xvpz -f 2.gz -C / --strip-components=2 (I discovered I need to use strip components because all files in the archive have the prefix backup/2/. I'll fix this for the next backup.) After the tar command completes, I log out of the box. Testing the backup When I try to log in again, it doesn't let me log in as vagrant with a password any more. It does let me log in as iain, my user on the live Linode, with a password. That surprised me because I disabled password authentication on my live Linode. I figured that I have to restart the ssh service for the change to take effect. Instead of restarting just ssh, I chose to restart the whole system. Now I can't even get to the login screen. PuTTY says "connection refused" when I try to connect. What went wrong?

Read the article

http request via iptables --to-destination ip redirect results in no response

- by Wouter Vegter

I have two Ubuntu servers with each having their own ip addresses. Let's call them server1 and server2, having respectively ip 1.1.1.1 and 2.2.2.2 I have a nginx running on server2. The sole purpose I want server1 to have is to redirect all incoming http (so port 80) requests to server2 without clients noticing that their request is being redirected. I tried the following command on server1: iptables -t nat -A PREROUTING -p tcp --dport 80 -j DNAT --to-destination 2.2.2.2 But when I enter 1.1.1.1 in my browser I get no respond: the page keeps trying to load without giving any message or error message (I get a time-out after 2-3 mins). But when I do remove the above iptables rule I immediately do get a "page not found error" when I enter 1.1.1.1 in my browser; so something is working but not as it should: when I enter 1.1.1.1 I want the html page to load that is hosted on 2.2.2.2 Because when i enter 2.2.2.2 in my browser I do see the webpage loaded. Could anyone please help me with this? I am searching quite some time (on severfault & Google) on this now so that's why I ask. Many thanks for reading my question! Update: Thank you all for you information. Unfortunately I still get no response I have the following iptables configuration: root@ip-10-48-238-216:/home/ubuntu# sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination root@ip-10-48-238-216:/home/ubuntu# sudo iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination DNAT tcp -- anywhere anywhere tcp dpt:www to:2.2.2.2 Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination When i run tcpdump and do request via chrome to 1.1.1.1 i get the following root@ip-10-48-238-216:/home/ubuntu# sudo tcpdump -i eth0 port 80 -vv tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 13:56:18.346625 IP (tos 0x0, ttl 52, id 12055, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16386 ip-10-48-238-216.eu-west-1.compute.internal.www: Flags [S], cksum 0xb398 (correct), seq 2639758575, win 5840, options [mss 1460,sackOK,TS val 1223672 ecr 0,nop,wscale 6], length 0 13:56:18.346662 IP (tos 0x0, ttl 51, id 12055, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16386 ww1dc1.shopreme.com.www: Flags [S], cksum 0x9ee0 (correct), seq 2639758575, win 5840, options [mss 1460,sackOK,TS val 1223672 ecr 0,nop,wscale 6], length 0 13:56:18.598747 IP (tos 0x0, ttl 52, id 10138, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16387 ip-10-48-238-216.eu-west-1.compute.internal.www: Flags [S], cksum 0xac40 (correct), seq 2645658541, win 5840, options [mss 1460,sackOK,TS val 1223735 ecr 0,nop,wscale 6], length 0 13:56:18.598777 IP (tos 0x0, ttl 51, id 10138, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16387 ww1dc1.shopreme.com.www: Flags [S], cksum 0x9788 (correct), seq 2645658541, win 5840, options [mss 1460,sackOK,TS val 1223735 ecr 0,nop,wscale 6], length 0 ^C 4 packets captured 4 packets received by filter 0 packets dropped by kernel the mentioned address relate to the following 212-123-161-112.ip.telfort.nl.16386 : my personal computer ww1dc1.shopreme.com.www : dns of server2 (2.2.2.2) ip-10-48-238-216.eu-west-1.compute.internal.www : amazon web services ec2 internal address of server1 (1.1.1.1) However, the tcpdump log on server2 (2.2.2.2) stays empty and I get no response back in my browser. I am able to ping from server1 to server2. And net.ipv4.ip_forward is set to 1 and so is /proc/sys/net/ipv4/ip_forward Could there be anything else that is missing?

Read the article

Neighbour table overflow on Linux hosts related to bridging and ipv6

- by tim

Note: I already have a workaround for this problem (as described below) so this is only a "want-to-know" question. I have a productive setup with around 50 hosts including blades running xen 4 and equallogics providing iscsi. All xen dom0s are almost plain Debian 5. The setup includes several bridges on every dom0 to support xen bridged networking. In total there are between 5 and 12 bridges on each dom0 servicing one vlan each. None of the hosts has routing enabled. At one point in time we moved one of the machines to a new hardware including a raid controller and so we installed an upstream 3.0.22/x86_64 kernel with xen patches. All other machines run debian xen-dom0-kernel. Since then we noticed on all hosts in the setup the following errors every ~2 minutes: [55888.881994] __ratelimit: 908 callbacks suppressed [55888.882221] Neighbour table overflow. [55888.882476] Neighbour table overflow. [55888.882732] Neighbour table overflow. [55888.883050] Neighbour table overflow. [55888.883307] Neighbour table overflow. [55888.883562] Neighbour table overflow. [55888.883859] Neighbour table overflow. [55888.884118] Neighbour table overflow. [55888.884373] Neighbour table overflow. [55888.884666] Neighbour table overflow. The arp table (arp -n) never showed more than around 20 entries on every machine. We tried the obvious tweaks and raised the /proc/sys/net/ipv4/neigh/default/gc_thresh* values. FInally to 16384 entries but no effect. Not even the interval of ~2 minutes changed which lead me to the conclusion that this is totally unrelated. tcpdump showed no uncommon ipv4 traffic on any interface. The only interesting finding from tcpdump were ipv6 packets bursting in like: 14:33:13.137668 IP6 fe80::216:3eff:fe1d:9d01 > ff02::1:ff1d:9d01: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:9d01, length 24 14:33:13.138061 IP6 fe80::216:3eff:fe1d:a8c1 > ff02::1:ff1d:a8c1: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:a8c1, length 24 14:33:13.138619 IP6 fe80::216:3eff:fe1d:bf81 > ff02::1:ff1d:bf81: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:bf81, length 24 14:33:13.138974 IP6 fe80::216:3eff:fe1d:eb41 > ff02::1:ff1d:eb41: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:eb41, length 24 which placed the idea in my mind that the problem maybe related to ipv6, since we have no ipv6 services in this setup. The only other hint was the coincidence of the host upgrade with the beginning of the problems. I powered down the host in question and the errors were gone. Then I subsequently took down the bridges on the host and when i took down (ifconfig down) one particularly bridge: br-vlan2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:120 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5286 (5.1 KiB) TX bytes:726 (726.0 B) eth0.2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1801 errors:0 dropped:0 overruns:0 frame:0 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:126228 (123.2 KiB) TX bytes:1464 (1.4 KiB) bridge name bridge id STP enabled interfaces ... br-vlan2158 8000.0026b9fb162c no eth0.2158 br-vlan2159 8000.0026b9fb162c no eth0.2159 The errors went away again. As you can see the bridge holds no ipv4 address and it's only member is eth0.2159 so no traffic should cross it. Bridge and interface .2159 / .2157 / .2158 which are in all aspects identical apart from the vlan they are connected to had no effect when taken down. Now I disabled ipv6 on the entire host via sysctl net.ipv6.conf.all.disable_ipv6 and rebooted. After this even with bridge br-vlan2159 enabled no errors occur. Any ideas are welcome.

Read the article

problem in run oracle server please help

- by rima

I used Oracle 11g, from few days ago I face below error: SQL*Plus: Release 11.2.0.1.0 Production on Thu Apr 7 07:33:19 2011 Copyright (c) 1982, 2010, Oracle. All rights reserved. Enter user-name: pentacms Enter password: ERROR: ORA-01033: ORACLE initialization or shutdown in progress Process ID: 0 Session ID: 0 Serial number: 0 Enter user-name: I try to solve the error, but it raised an other error, I try to open log file but I receive below error(last line) "ERROR at line 1: ORA-00600: internal error code, arguments: [kcratr_nab_less_than_odr], [1], [46], [32689], [32690], [], [], [], [], [], [], [] " please advice me, It's an emergency case. FIXED_TABLE_SEQUENCE ROW_WAIT_OBJ# ROW_WAIT_FILE# ROW_WAIT_BLOCK# ROW_WAIT_ROW# -------------------- ------------- -------------- --------------- ------------- TOP_LEVEL_CALL# LOGON_TIM LAST_CALL_ET PDM FAILOVER_TYPE FAILOVER_M FAI --------------- --------- ------------ --- ------------- ---------- --- RESOURCE_CONSUMER_GROUP PDML_STA PDDL_STA PQ_STATU -------------------------------- -------- -------- -------- CURRENT_QUEUE_DURATION ---------------------- CLIENT_IDENTIFIER BLOCKING_SE ---------------------------------------------------------------- ----------- BLOCKING_INSTANCE BLOCKING_SESSION FINAL_BLOCK FINAL_BLOCKING_INSTANCE ----------------- ---------------- ----------- ----------------------- FINAL_BLOCKING_SESSION SEQ# EVENT# ---------------------- ---------- ---------- EVENT ---------------------------------------------------------------- P1TEXT P1 ---------------------------------------------------------------- ---------- P1RAW ---------------- P2TEXT P2 ---------------------------------------------------------------- ---------- P2RAW ---------------- P3TEXT P3 ---------------------------------------------------------------- ---------- P3RAW WAIT_CLASS_ID WAIT_CLASS# ---------------- ------------- ----------- WAIT_CLASS WAIT_TIME ---------------------------------------------------------------- ---------- SECONDS_IN_WAIT STATE WAIT_TIME_MICRO TIME_REMAINING_MICRO --------------- ------------------- --------------- -------------------- TIME_SINCE_LAST_WAIT_MICRO -------------------------- SERVICE_NAME SQL_TRAC SQL_T ---------------------------------------------------------------- -------- ----- SQL_T SQL_TRACE_ SESSION_EDITION_ID CREATOR_ADDR CREATOR_SERIAL# ----- ---------- ------------------ ---------------- --------------- ECID ---------------------------------------------------------------- SYS$USERS DISABLED FALSE SADDR SID SERIAL# AUDSID PADDR USER# ---------------- ---------- ---------- ---------- ---------------- ---------- USERNAME COMMAND OWNERID TADDR ------------------------------ ---------- ---------- ---------------- LOCKWAIT STATUS SERVER SCHEMA# SCHEMANAME ---------------- -------- --------- ---------- ------------------------------ OSUSER PROCESS ------------------------------ ------------------------ MACHINE PORT ---------------------------------------------------------------- ---------- TERMINAL ---------------- PROGRAM TYPE ---------------------------------------------------------------- ---------- SQL_ADDRESS SQL_HASH_VALUE SQL_ID SQL_CHILD_NUMBER SQL_EXEC_ ---------------- -------------- ------------- ---------------- --------- SQL_EXEC_ID PREV_SQL_ADDR PREV_HASH_VALUE PREV_SQL_ID PREV_CHILD_NUMBER ----------- ---------------- --------------- ------------- ----------------- PREV_EXEC PREV_EXEC_ID PLSQL_ENTRY_OBJECT_ID PLSQL_ENTRY_SUBPROGRAM_ID --------- ------------ --------------------- ------------------------- PLSQL_OBJECT_ID PLSQL_SUBPROGRAM_ID --------------- ------------------- MODULE MODULE_HASH ------------------------------------------------ ----------- ACTION ACTION_HASH -------------------------------- ----------- CLIENT_INFO ---------------------------------------------------------------- FIXED_TABLE_SEQUENCE ROW_WAIT_OBJ# ROW_WAIT_FILE# ROW_WAIT_BLOCK# ROW_WAIT_ROW# -------------------- ------------- -------------- --------------- ------------- TOP_LEVEL_CALL# LOGON_TIM LAST_CALL_ET PDM FAILOVER_TYPE FAILOVER_M FAI --------------- --------- ------------ --- ------------- ---------- --- RESOURCE_CONSUMER_GROUP PDML_STA PDDL_STA PQ_STATU -------------------------------- -------- -------- -------- CURRENT_QUEUE_DURATION ---------------------- CLIENT_IDENTIFIER BLOCKING_SE ---------------------------------------------------------------- ----------- BLOCKING_INSTANCE BLOCKING_SESSION FINAL_BLOCK FINAL_BLOCKING_INSTANCE ----------------- ---------------- ----------- ----------------------- FINAL_BLOCKING_SESSION SEQ# EVENT# ---------------------- ---------- ---------- EVENT ---------------------------------------------------------------- P1TEXT P1 ---------------------------------------------------------------- ---------- P1RAW ---------------- P2TEXT P2 ---------------------------------------------------------------- ---------- P2RAW ---------------- P3TEXT P3 ---------------------------------------------------------------- ---------- P3RAW WAIT_CLASS_ID WAIT_CLASS# ---------------- ------------- ----------- WAIT_CLASS WAIT_TIME ---------------------------------------------------------------- ---------- SECONDS_IN_WAIT STATE WAIT_TIME_MICRO TIME_REMAINING_MICRO --------------- ------------------- --------------- -------------------- TIME_SINCE_LAST_WAIT_MICRO -------------------------- SERVICE_NAME SQL_TRAC SQL_T ---------------------------------------------------------------- -------- ----- SQL_T SQL_TRACE_ SESSION_EDITION_ID CREATOR_ADDR CREATOR_SERIAL# ----- ---------- ------------------ ---------------- --------------- ECID ---------------------------------------------------------------- FALSE FIRST EXEC 0 000007FF5D4D8D70 2 SADDR SID SERIAL# AUDSID PADDR USER# ---------------- ---------- ---------- ---------- ---------------- ---------- USERNAME COMMAND OWNERID TADDR ------------------------------ ---------- ---------- ---------------- LOCKWAIT STATUS SERVER SCHEMA# SCHEMANAME ---------------- -------- --------- ---------- ------------------------------ OSUSER PROCESS ------------------------------ ------------------------ MACHINE PORT ---------------------------------------------------------------- ---------- TERMINAL ---------------- PROGRAM TYPE ---------------------------------------------------------------- ---------- SQL_ADDRESS SQL_HASH_VALUE SQL_ID SQL_CHILD_NUMBER SQL_EXEC_ ---------------- -------------- ------------- ---------------- --------- SQL_EXEC_ID PREV_SQL_ADDR PREV_HASH_VALUE PREV_SQL_ID PREV_CHILD_NUMBER ----------- ---------------- --------------- ------------- ----------------- PREV_EXEC PREV_EXEC_ID PLSQL_ENTRY_OBJECT_ID PLSQL_ENTRY_SUBPROGRAM_ID --------- ------------ --------------------- ------------------------- PLSQL_OBJECT_ID PLSQL_SUBPROGRAM_ID --------------- ------------------- MODULE MODULE_HASH ------------------------------------------------ ----------- ACTION ACTION_HASH -------------------------------- ----------- CLIENT_INFO ---------------------------------------------------------------- FIXED_TABLE_SEQUENCE ROW_WAIT_OBJ# ROW_WAIT_FILE# ROW_WAIT_BLOCK# ROW_WAIT_ROW# -------------------- ------------- -------------- --------------- ------------- TOP_LEVEL_CALL# LOGON_TIM LAST_CALL_ET PDM FAILOVER_TYPE FAILOVER_M FAI --------------- --------- ------------ --- ------------- ---------- --- RESOURCE_CONSUMER_GROUP PDML_STA PDDL_STA PQ_STATU -------------------------------- -------- -------- -------- CURRENT_QUEUE_DURATION ---------------------- CLIENT_IDENTIFIER BLOCKING_SE ---------------------------------------------------------------- ----------- BLOCKING_INSTANCE BLOCKING_SESSION FINAL_BLOCK FINAL_BLOCKING_INSTANCE ----------------- ---------------- ----------- ----------------------- FINAL_BLOCKING_SESSION SEQ# EVENT# ---------------------- ---------- ---------- EVENT ---------------------------------------------------------------- P1TEXT P1 ---------------------------------------------------------------- ---------- P1RAW ---------------- P2TEXT P2 ---------------------------------------------------------------- ---------- P2RAW ---------------- P3TEXT P3 ---------------------------------------------------------------- ---------- P3RAW WAIT_CLASS_ID WAIT_CLASS# ---------------- ------------- ----------- WAIT_CLASS WAIT_TIME ---------------------------------------------------------------- ---------- SECONDS_IN_WAIT STATE WAIT_TIME_MICRO TIME_REMAINING_MICRO --------------- ------------------- --------------- -------------------- TIME_SINCE_LAST_WAIT_MICRO -------------------------- SERVICE_NAME SQL_TRAC SQL_T ---------------------------------------------------------------- -------- ----- SQL_T SQL_TRACE_ SESSION_EDITION_ID CREATOR_ADDR CREATOR_SERIAL# ----- ---------- ------------------ ---------------- --------------- ECID ---------------------------------------------------------------- SADDR SID SERIAL# AUDSID PADDR USER# ---------------- ---------- ---------- ---------- ---------------- ---------- USERNAME COMMAND OWNERID TADDR ------------------------------ ---------- ---------- ---------------- LOCKWAIT STATUS SERVER SCHEMA# SCHEMANAME ---------------- -------- --------- ---------- ------------------------------ OSUSER PROCESS ------------------------------ ------------------------ MACHINE PORT ---------------------------------------------------------------- ---------- TERMINAL ---------------- PROGRAM TYPE ---------------------------------------------------------------- ---------- SQL_ADDRESS SQL_HASH_VALUE SQL_ID SQL_CHILD_NUMBER SQL_EXEC_ ---------------- -------------- ------------- ---------------- --------- SQL_EXEC_ID PREV_SQL_ADDR PREV_HASH_VALUE PREV_SQL_ID PREV_CHILD_NUMBER ----------- ---------------- --------------- ------------- ----------------- PREV_EXEC PREV_EXEC_ID PLSQL_ENTRY_OBJECT_ID PLSQL_ENTRY_SUBPROGRAM_ID --------- ------------ --------------------- ------------------------- PLSQL_OBJECT_ID PLSQL_SUBPROGRAM_ID --------------- ------------------- MODULE MODULE_HASH ------------------------------------------------ ----------- ACTION ACTION_HASH -------------------------------- ----------- CLIENT_INFO ---------------------------------------------------------------- FIXED_TABLE_SEQUENCE ROW_WAIT_OBJ# ROW_WAIT_FILE# ROW_WAIT_BLOCK# ROW_WAIT_ROW# -------------------- ------------- -------------- --------------- ------------- TOP_LEVEL_CALL# LOGON_TIM LAST_CALL_ET PDM FAILOVER_TYPE FAILOVER_M FAI --------------- --------- ------------ --- ------------- ---------- --- RESOURCE_CONSUMER_GROUP PDML_STA PDDL_STA PQ_STATU -------------------------------- -------- -------- -------- CURRENT_QUEUE_DURATION ---------------------- CLIENT_IDENTIFIER BLOCKING_SE ---------------------------------------------------------------- ----------- BLOCKING_INSTANCE BLOCKING_SESSION FINAL_BLOCK FINAL_BLOCKING_INSTANCE ----------------- ---------------- ----------- ----------------------- FINAL_BLOCKING_SESSION SEQ# EVENT# ---------------------- ---------- ---------- EVENT ---------------------------------------------------------------- P1TEXT P1 ---------------------------------------------------------------- ---------- P1RAW ---------------- P2TEXT P2 ---------------------------------------------------------------- ---------- P2RAW ---------------- P3TEXT P3 ---------------------------------------------------------------- ---------- P3RAW WAIT_CLASS_ID WAIT_CLASS# ---------------- ------------- ----------- WAIT_CLASS WAIT_TIME ---------------------------------------------------------------- ---------- SECONDS_IN_WAIT STATE WAIT_TIME_MICRO TIME_REMAINING_MICRO --------------- ------------------- --------------- -------------------- TIME_SINCE_LAST_WAIT_MICRO -------------------------- SERVICE_NAME SQL_TRAC SQL_T ---------------------------------------------------------------- -------- ----- SQL_T SQL_TRACE_ SESSION_EDITION_ID CREATOR_ADDR CREATOR_SERIAL# ----- ---------- ------------------ ---------------- --------------- ECID ---------------------------------------------------------------- 16 rows selected. SQL> desc dba_user; ERROR: ORA-04043: object dba_user does not exist SQL> desc dba_users; ERROR: ORA-04043: object dba_users does not exist SQL> desc v$user; ERROR: ORA-04043: object v$user does not exist SQL> desc v$users ERROR: ORA-04043: object v$users does not exist SQL> seleect * from dba_users; SP2-0734: unknown command beginning "seleect * ..." - rest of line ignored. SQL> select * from dba_users; select * from dba_users * ERROR at line 1: ORA-01219: database not open: queries allowed on fixed tables/views only SQL> alter database open; alter database open * ERROR at line 1: ORA-00600: internal error code, arguments: [kcratr_nab_less_than_odr], [1], [46], [32689], [32690], [], [], [], [], [], [], [] SQL> alter database mount; alter database mount * ERROR at line 1: ORA-01100: database already mounted SQL> alter database mount;

Read the article

ls hangs for a certain directory

- by Jakobud

There is a particular directory (/var/www), that when I run ls (with or without some options), the command hangs and never completes. There is only about 10-15 files and directories in /var/www. Mostly just text files. Here is some investigative info: [me@server www]$ df . Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_dev-lv_root 50G 19G 29G 40% / [me@server www]$ df -i . Filesystem Inodes IUsed IFree IUse% Mounted on /dev/mapper/vg_dev-lv_root 3.2M 435K 2.8M 14% / find works fine. Also I can type in cd /var/www/ and press TAB before pressing enter and it will successfully tab-completion list of all files/directories in there: [me@server www]$ cd /var/www/ cgi-bin/ create_vhost.sh html/ manual/ phpMyAdmin/ scripts/ usage/ conf/ error/ icons/ mediawiki/ rackspace sqlbuddy/ vhosts/ [me@server www]$ cd /var/www/ I have had to kill my terminal sessions several times because of the ls hanging: [me@server ~]$ ps | grep ls gdm 6215 0.0 0.0 488152 2488 ? S<sl Jan18 0:00 /usr/bin/pulseaudio --start --log-target=syslog root 23269 0.0 0.0 117724 1088 ? D 18:24 0:00 ls -Fh --color=always -l root 23477 0.0 0.0 117724 1088 ? D 18:34 0:00 ls -Fh --color=always -l root 23579 0.0 0.0 115592 820 ? D 18:36 0:00 ls -Fh --color=always root 23634 0.0 0.0 115592 816 ? D 18:38 0:00 ls -Fh --color=always root 23740 0.0 0.0 117724 1088 ? D 18:40 0:00 ls -Fh --color=always -l me 23770 0.0 0.0 103156 816 pts/6 S+ 18:41 0:00 grep ls kill doesn't seem to have any affect on the processes, even as sudo. What else should I do to investigate this problem? It just randomly started happening today. UPDATE dmesg is a big list of things, mostly related to an external USB HDD that I've mounted too many times and the max mount count has been reached, but that is an un-related problem I think. Near the bottom of dmesg I'm seeing this: INFO: task ls:23579 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. ls D ffff88041fc230c0 0 23579 23505 0x00000080 ffff8801688a1bb8 0000000000000086 0000000000000000 ffffffff8119d279 ffff880406d0ea20 ffff88007e2c2268 ffff880071fe80c8 00000003ae82967a ffff880407169ad8 ffff8801688a1fd8 0000000000010518 ffff880407169ad8 Call Trace: [<ffffffff8119d279>] ? __find_get_block+0xa9/0x200 [<ffffffff814c97ae>] __mutex_lock_slowpath+0x13e/0x180 [<ffffffff814c964b>] mutex_lock+0x2b/0x50 [<ffffffff8117a4d3>] do_lookup+0xd3/0x220 [<ffffffff8117b145>] __link_path_walk+0x6f5/0x1040 [<ffffffff8117a47d>] ? do_lookup+0x7d/0x220 [<ffffffff8117bd1a>] path_walk+0x6a/0xe0 [<ffffffff8117beeb>] do_path_lookup+0x5b/0xa0 [<ffffffff8117cb57>] user_path_at+0x57/0xa0 [<ffffffff81178986>] ? generic_readlink+0x76/0xc0 [<ffffffff8117cb62>] ? user_path_at+0x62/0xa0 [<ffffffff81171d3c>] vfs_fstatat+0x3c/0x80 [<ffffffff81258ae5>] ? _atomic_dec_and_lock+0x55/0x80 [<ffffffff81171eab>] vfs_stat+0x1b/0x20 [<ffffffff81171ed4>] sys_newstat+0x24/0x50 [<ffffffff810d40a2>] ? audit_syscall_entry+0x272/0x2a0 [<ffffffff81013172>] system_call_fastpath+0x16/0x1b And also, strace ls /var/www/ spits out a whole BUNCH of information. I don't know what is useful here... The last handful of lines: ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig icanon echo ...}) = 0 ioctl(1, TIOCGWINSZ, {ws_row=68, ws_col=145, ws_xpixel=0, ws_ypixel=0}) = 0 stat("/var/www/", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 open("/var/www/", O_RDONLY|O_NONBLOCK|O_DIRECTORY|O_CLOEXEC) = 3 fcntl(3, F_GETFD) = 0x1 (flags FD_CLOEXEC) getdents(3, /* 16 entries */, 32768) = 488 getdents(3, /* 0 entries */, 32768) = 0 close(3) = 0 fstat(1, {st_mode=S_IFCHR|0620, st_rdev=makedev(136, 9), ...}) = 0 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f3093b18000 write(1, "cgi-bin conf create_vhost.sh\te"..., 125cgi-bin conf create_vhost.sh error html icons manual mediawiki phpMyAdmin rackspace scripts sqlbuddy usage vhosts ) = 125 close(1) = 0 munmap(0x7f3093b18000, 4096) = 0 close(2) = 0 exit_group(0) = ?

Read the article

segfault when cd-ing into certain directories in bash

- by user84207

I have noticed this very strange behavior recently. After cd into certain directories, I get a segfault on the terminal. --- SIGSEGV (Segmentation fault) @ 0 (0) --- --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV (core dumped) +++ segmentation fault (core dumped) I proceeded to strace a bash session in which I cd into the target directory, and was able to reproduce the problem. I attached the log to this pastebin: I paste below the few lines from the read of "cd stumpwm", which is the directory in question, until the segfault. I included a few of the repetitions of calls to "rt_sigprocmask" and "brk" to give a glimpse of the pattern, which occurs for most of the strace, read(0, cd stumpwm "c", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "d", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, " ", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "s", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "t", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "u", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "m", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "p", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "w", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "m", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "\n", 1) = 1 rt_sigprocmask(SIG_BLOCK, [INT], [], 8) = 0 ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig -icanon -echo ...}) = 0 ioctl(0, SNDCTL_TMR_STOP or TCSETSW, {B38400 opost isig icanon -echo ...}) = 0 ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig icanon -echo ...}) = 0 rt_sigprocmask(SIG_SETMASK, [], NULL, 8) = 0 rt_sigaction(SIGINT, {0x457d50, [], SA_RESTORER, 0x7ffff76254a0}, {0x49edc0, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTERM, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGQUIT, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGALRM, {0x457f50, [HUP INT ILL TRAP ABRT BUS FPE USR1 SEGV USR2 PIPE ALRM TERM XCPU XFSZ VTALRM SYS], SA_RESTORER, 0x7ffff76254a0}, {0x49edc0, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTSTP, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTTOU, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTTIN, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGWINCH, {0x457920, [], SA_RESTORER, 0x7ffff76254a0}, {0x49e6e0, [], SA_RESTORER|SA_RESTART, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGINT, {0x457d50, [], SA_RESTORER, 0x7ffff76254a0}, {0x457d50, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 brk(0xa9a000) = 0xa9a000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9b000) = 0xa9b000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9c000) = 0xa9c000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9d000) = 0xa9d000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9e000) = 0xa9e000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9f000) = 0xa9f000 brk(0xaa0000) = 0xaa0000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xaa1000) = 0xaa1000 brk(0xaa2000) = 0xaa2000 (pattern of rt_sigprocmask, brk continues ...) rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0x1d5b000) = 0x1d5b000 brk(0x1d5c000) = 0x1d5c000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0x1d5d000) = 0x1d5d000 brk(0x1d5e000) = 0x1d5e000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 --- SIGSEGV (Segmentation fault) @ 0 (0) --- --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV (core dumped) +++ segmentation fault (core dumped) How can I debug this? Is this likely to be a bash problem? The error does not occur with another shell, such as eshell. I have also run an fschk, although I haven't been able to see the output because of this bug.

Read the article

Can't sync filesystem without reboot

- by Fabio

I'm having an issue with a linux server. Once a week the running mysql instance hangs and there is no way to fully stop it. If I kill it, it remains in zombie status and init does not reap its pid. The server is used for staging deployments and some internal tools, so it's not under heavy load. The only process constantly used id mysql and for this I think that it's the only process which suffer of this issue. I've searched system logs for errors and the only thing I found is this error (repeated a couple of times) in dmesg output: [706560.640085] INFO: task mysqld:31965 blocked for more than 120 seconds. [706560.640198] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [706560.640312] mysqld D ffff88032fd93f40 0 31965 1 0x00000000 [706560.640317] ffff880242a27d18 0000000000000086 ffff88031a50dd00 ffff880242a27fd8 [706560.640321] ffff880242a27fd8 ffff880242a27fd8 ffff88031e549740 ffff88031a50dd00 [706560.640325] ffff88031a50dd00 ffff88032fd947f8 0000000000000002 ffffffff8112f250 [706560.640328] Call Trace: [706560.640338] [<ffffffff8112f250>] ? __lock_page+0x70/0x70 [706560.640344] [<ffffffff816cb1b9>] schedule+0x29/0x70 [706560.640347] [<ffffffff816cb28f>] io_schedule+0x8f/0xd0 [706560.640350] [<ffffffff8112f25e>] sleep_on_page+0xe/0x20 [706560.640353] [<ffffffff816c9900>] __wait_on_bit+0x60/0x90 [706560.640356] [<ffffffff8112f390>] wait_on_page_bit+0x80/0x90 [706560.640360] [<ffffffff8107dce0>] ? autoremove_wake_function+0x40/0x40 [706560.640363] [<ffffffff8112f891>] filemap_fdatawait_range+0x101/0x190 [706560.640366] [<ffffffff81130975>] filemap_write_and_wait_range+0x65/0x70 [706560.640371] [<ffffffff8122e441>] ext4_sync_file+0x71/0x320 [706560.640376] [<ffffffff811c3e6d>] do_fsync+0x5d/0x90 [706560.640379] [<ffffffff811c40d0>] sys_fsync+0x10/0x20 [706560.640383] [<ffffffff816d495d>] system_call_fastpath+0x1a/0x1f When this happens the only way to make everything working again is a full reboot, but in order to do that I'm forced to use this command after I've manually stopped all running processes echo b > /proc/sysrq-trigger otherwise normal reboot process hangs forever. I've tracked reboots script and I've found out that also the reboot process hangs on a sync call, this one in /etc/init.d/sendsigs (I'm on ubuntu) # Flush the kernel I/O buffer before we start to kill # processes, to make sure the IO of already stopped services to # not slow down the remaining processes to a point where they # are accidentily killed with SIGKILL because they did not # manage to shut down in time. sync I'm almost sure that the cause of this is an hardware issue (the RAID controller???) also because I've other two machines with the same hardware and software configuration and they don't suffer of this, but I can't find any hint in syslog or dmesg. I've also installed smartmontools and mcelog packages but none of them did report any issue. What can I do to track the cause of this issue? Today is happened again, here is the status of system after triggering a reboot init---console-kit-dae---64*[{console-kit-dae}] +-dbus-daemon +-mcelog +-mysqld---{mysqld} +-newrelic-daemon---newrelic-daemon---11*[{newrelic-daemon}] +-ntpd +-polkitd---{polkitd} +-python3 +-rpc.idmapd +-rpc.statd +-rpcbind +-sh---rc---S20sendsigs---sync +-smartd +-snmpd +-sshd---sshd---zsh---sudo---zsh---pstree +-sshd---sshd---zsh---sudo---zsh And here is the status of sync process # ps aux | grep sync root 3637 0.1 0.0 4352 372 ? D 05:53 0:00 sync i.e. Uninterruptible sleep... Hardware specs as reported by lshw I think the raid controller is a fake raid. I usually don't deal with hardware (and for the record I don't have physical access to it) description: Computer product: X7DBP () vendor: Supermicro version: 0123456789 serial: 0123456789 width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=53D19F64-D663-A017-8922-0030487C1FEE *-core description: Motherboard product: X7DBP vendor: Supermicro physical id: 0 version: PCB Version serial: 0123456789 *-firmware description: BIOS vendor: Phoenix Technologies LTD physical id: 0 version: 6.00 date: 05/29/2007 size: 106KiB capacity: 960KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect edd int13floppy2880 acpi usb ls120boot zipboot biosbootspecification *-storage description: RAID bus controller product: 631xESB/632xESB SATA RAID Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 09 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list configuration: driver=ahci latency=0 resources: irq:19 ioport:18a0(size=8) ioport:1874(size=4) ioport:1878(size=8) ioport:1870(size=4) ioport:1880(size=32) memory:d8500400-d85007ff

Read the article

How to install pip/easy_install on debian 6 for python3.2

- by atomAltera

I'm trying to install pip or setup tools form python 3.2 in debian 6. First case: apt-get install python3-pip...OK python3 easy_install.py webob Searching for webob Reading http://pypi.python.org/simple/webob/ Reading http://webob.org/ Reading http://pythonpaste.org/webob/ Best match: WebOb 1.2.2 Downloading http://pypi.python.org/packages/source/W/WebOb/WebOb-1.2.2.zip#md5=de0f371b46554709ce5b93c088a11cae Processing WebOb-1.2.2.zip Traceback (most recent call last): File "easy_install.py", line 5, in <module> main() File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 1931, in main with_ei_usage(lambda: File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 1912, in with_ei_usage return f() File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 1935, in <lambda> distclass=DistributionWithoutHelpCommands, **kw File "/usr/local/lib/python3.2/distutils/core.py", line 148, in setup dist.run_commands() File "/usr/local/lib/python3.2/distutils/dist.py", line 917, in run_commands self.run_command(cmd) File "/usr/local/lib/python3.2/distutils/dist.py", line 936, in run_command cmd_obj.run() File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 368, in run self.easy_install(spec, not self.no_deps) File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 608, in easy_install return self.install_item(spec, dist.location, tmpdir, deps) File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 638, in install_item dists = self.install_eggs(spec, download, tmpdir) File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 799, in install_eggs unpack_archive(dist_filename, tmpdir, self.unpack_progress) File "/usr/lib/python3/dist-packages/setuptools/archive_util.py", line 67, in unpack_archive driver(filename, extract_dir, progress_filter) File "/usr/lib/python3/dist-packages/setuptools/archive_util.py", line 154, in unpack_zipfile data = z.read(info.filename) File "/usr/local/lib/python3.2/zipfile.py", line 891, in read with self.open(name, "r", pwd) as fp: File "/usr/local/lib/python3.2/zipfile.py", line 980, in open close_fileobj=not self._filePassed) File "/usr/local/lib/python3.2/zipfile.py", line 489, in __init__ self._decompressor = zlib.decompressobj(-15) AttributeError: 'NoneType' object has no attribute 'decompressobj' Second case: from http://pypi.python.org/pypi/distribute#installation-instructions python3 distribute_setup.py Downloading http://pypi.python.org/packages/source/d/distribute/distribute-0.6.28.tar.gz Extracting in /tmp/tmpv6iei2 Traceback (most recent call last): File "distribute_setup.py", line 515, in <module> main(sys.argv[1:]) File "distribute_setup.py", line 511, in main _install(tarball, _build_install_args(argv)) File "distribute_setup.py", line 73, in _install tar = tarfile.open(tarball) File "/usr/local/lib/python3.2/tarfile.py", line 1746, in open raise ReadError("file could not be opened successfully") tarfile.ReadError: file could not be opened successfully Third case: from http://pypi.python.org/pypi/distribute#installation-instructions tar -xzvf distribute-0.6.28.tar.gz cd distribute-0.6.28 python3 setup.py install Before install bootstrap. Scanning installed packages No setuptools distribution found running install running bdist_egg running egg_info writing distribute.egg-info/PKG-INFO writing top-level names to distribute.egg-info/top_level.txt writing dependency_links to distribute.egg-info/dependency_links.txt writing entry points to distribute.egg-info/entry_points.txt reading manifest file 'distribute.egg-info/SOURCES.txt' reading manifest template 'MANIFEST.in' writing manifest file 'distribute.egg-info/SOURCES.txt' installing library code to build/bdist.linux-x86_64/egg running install_lib running build_py copying distribute.egg-info/PKG-INFO -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/SOURCES.txt -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/dependency_links.txt -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/entry_points.txt -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/top_level.txt -> build/bdist.linux-x86_64/egg/EGG-INFO creating 'dist/distribute-0.6.28-py3.2.egg' and adding 'build/bdist.linux-x86_64/egg' to it Traceback (most recent call last): File "setup.py", line 220, in <module> scripts = scripts, File "/usr/local/lib/python3.2/distutils/core.py", line 148, in setup dist.run_commands() File "/usr/local/lib/python3.2/distutils/dist.py", line 917, in run_commands self.run_command(cmd) File "/usr/local/lib/python3.2/distutils/dist.py", line 936, in run_command cmd_obj.run() File "build/src/setuptools/command/install.py", line 73, in run self.do_egg_install() File "build/src/setuptools/command/install.py", line 93, in do_egg_install self.run_command('bdist_egg') File "/usr/local/lib/python3.2/distutils/cmd.py", line 313, in run_command self.distribution.run_command(command) File "/usr/local/lib/python3.2/distutils/dist.py", line 936, in run_command cmd_obj.run() File "build/src/setuptools/command/bdist_egg.py", line 241, in run dry_run=self.dry_run, mode=self.gen_header()) File "build/src/setuptools/command/bdist_egg.py", line 542, in make_zipfile z = zipfile.ZipFile(zip_filename, mode, compression=compression) File "/usr/local/lib/python3.2/zipfile.py", line 689, in __init__ "Compression requires the (missing) zlib module") RuntimeError: Compression requires the (missing) zlib module zlib1g-dev installed Help me please

Read the article

iCloud stuff stops working while connected to OpenVPN

- by Taco Bob

I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again! (I tried serverfault, it was closed as off-topic. I'm trying here and the Unix site as well. Here because it's a more general audience that might know more about OpenVPN based on the number of questions I see asked about it) EDIT: -I have also tried upgrading to Version: 2.3-beta1-debian0 - issue persists. -Removed all iptables rules except for the ones that flush -left this rule:iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source (server ip) -added iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT still, nothing works. I can see traffic in tcpdump on the server if i watch the tunnel: 20:03:48.702835 IP nk11p01st-courier105-bz.push.apple.com.5223 10.9.8.6.60772: Flags [F.], seq 2635, ack 1218, win 76, options [nop,nop,TS val 914984811 ecr 745921298], length 0 20:03:48.911244 IP 10.9.8.6.60772 nk11p01st-courier105-bz.push.apple.com.5223: Flags [R], seq 3621143451, win 0, length 0 But still, no push messages/notifications are ever delivered. :/ EDIT: * Further testing indicates that it might actually be the client after all.

Read the article

Postfix logs missing information on delivery status (postfix/smtp message)

- by hegemon

I noticed a problem with postfix logs, that information on some of emails delivery status is missing. The issue affects about 1% of emails. "Healthy" log: <server># grep 8EB992EFBB44 postfix_log/mail04.log Jun 5 03:09:29 mail04 postfix/smtpd[8537]: 8EB992EFBB44: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 03:09:29 mail04 postfix/cleanup[34349]: 8EB992EFBB44: message-id=<[email protected]> Jun 5 03:12:02 mail04 postfix/qmgr[76377]: 8EB992EFBB44: from=<[email protected]>, size=48845, nrcpt=1 (queue active) Jun 5 03:15:12 mail04 postfix/smtp[35058]: 8EB992EFBB44: to=<[email protected]>, relay=mx.baz.com[xxx.xxx.xxx.xxx]:25, conn_use=70, delay=343, delays=153/190/0/0.24, dsn=2.0.0, status=sent (250 ok) Jun 5 03:15:12 mail04 postfix/qmgr[76377]: 8EB992EFBB44: removed "Broken" log: <server># grep F3C362EF37CA postfix_log/mail04.log Jun 5 04:03:27 mail04 postfix/smtpd[39666]: F3C362EF37CA: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 04:03:27 mail04 postfix/cleanup[41287]: F3C362EF37CA: message-id=<[email protected]> Jun 5 04:03:28 mail04 postfix/qmgr[76377]: F3C362EF37CA: from=<[email protected]>, size=48892, nrcpt=1 (queue active) ** here should be a log line from postfix/smtp but there is none ** Jun 5 04:03:29 mail04 postfix/qmgr[76377]: F3C362EF37CA: removed Background information: system: FreeBSD xxx.xxx.xxx 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 Postfix is installed inside jail. Logs are on the same machine, log dir is mounted thru nullfs. The site has spikes of heavy load, causing disks (local) to run at 100%. Update The log is rotated daily, current size is ~ 500MB. I made a test by queuing 99000 messages to same destination (in order to rule out dns/network/mx issues). 5715 messages don't have any DSN record. Failed messages queue time is spread evenly over time, i don't see any time-bound issues. Some undelivered emails: envelopeid | processed_time --------------+---------------------------- 8D7652EF3BAE | 2012-06-06 13:19:11.072715 DD53A2EF3C5C | 2012-06-06 13:33:24.374783 8C52F2EF4E3F | 2012-06-06 13:39:15.810616 BBC572EF525C | 2012-06-06 13:44:22.762812 E95822EF54D1 | 2012-06-06 13:52:01.134533 839DD2EF4FBB | 2012-06-06 14:13:48.511236 017EE2EF6234 | 2012-06-06 15:04:48.618963 Those are a few picks, such records of undelivered email occur almost every second. <server># egrep '(8D7652EF3BAE|BBC572EF525C|017EE2EF6234)' mail04.log Jun 6 13:19:10 mail04 postfix/smtpd[20350]: 8D7652EF3BAE: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:19:10 mail04 postfix/cleanup[21024]: 8D7652EF3BAE: message-id=<[email protected]> Jun 6 13:19:10 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: from=<[email protected]>, size=63718, nrcpt=1 (queue active) Jun 6 13:19:11 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: removed Jun 6 13:44:22 mail04 postfix/smtpd[20346]: BBC572EF525C: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:44:22 mail04 postfix/cleanup[24811]: BBC572EF525C: message-id=<[email protected]> Jun 6 13:44:22 mail04 postfix/qmgr[7939]: BBC572EF525C: from=<[email protected]>, size=63758, nrcpt=1 (queue active) Jun 6 15:04:49 mail04 postfix/smtpd[20344]: 017EE2EF6234: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 15:04:49 mail04 postfix/cleanup[35585]: 017EE2EF6234: message-id=<[email protected]> Jun 6 15:04:49 mail04 postfix/qmgr[7939]: 017EE2EF6234: from=<[email protected]>, size=63706, nrcpt=1 (queue active) <server># <server># find /var/spool/postfix/active/ -type f -print | wc -l 1 <server># IMPORTANT: As you can see above some of emails doesn't event have the removed line.

Read the article

/usr/bin/sshd isn't linked against PAM on one of my systems. What is wrong and how can I fix it?

- by marc.riera

Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password Edit2: UsePAM yes fails With this configuration ssh fails to start : root@linserv9:/home/admmarc# cat /etc/ssh/sshd_config |grep -vE "^[ \t]*$|^#" Port 22 Protocol 2 ListenAddress 0.0.0.0 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys ChallengeResponseAuthentication yes UsePAM yes Subsystem sftp /usr/lib/sftp-server root@linserv9:/home/admmarc# The error it gives is as follows root@linserv9:/home/admmarc# /etc/init.d/ssh start * Starting OpenBSD Secure Shell server sshd /etc/ssh/sshd_config: line 75: Bad configuration option: UsePAM /etc/ssh/sshd_config: terminating, 1 bad configuration options ...fail! root@linserv9:/home/admmarc#

Read the article

Linux: Apple Wireless A1314 Fn key not registered, looks like software bug

- by ramplank

I'm trying to set up my Apple Wireless Keyboard with my Kubuntu systems. These are PC hardware powered by Intel Atom and Intel i5 respectively. The keyboard has a US keyboard layout and has model number A1314 written on the back. It takes two AA batteries. I'm saying that because it appears there are multiple types of model A1314. I have tried this on a 10.04, 11.04, 11.10 and 12.04 system with no success. Every time using a bluetooth dongle and the KDE bluetooth notification tray applet, the keyboard can be connected. In both cases it shows up as "Apple Wireless Keyboard". Almost everything works as expected, in fact, I'm typing on it right now. But one thing doesn't: The Fn key. I'd like to use Fn + Down Arrow as PgDn / Page Down, I understand this is default behaviour on Apple keyboards. And of course I'd like the same for Page Up, Home and End. I'll stick to Page Down in my example. I used the xev tool to see the keycodes the system receives, and if I press on Fn nothing happens, and nothing is registered. If I press Fn + Down Arrow, xev only registers the down arrow. Here's the output from my 11.04 system to illustrate: Press just the Fn key: no output Press Down Arrow key: KeyPress event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2699773, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2699860, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False Press Fn+Down Arrow Keys together: KeyPress event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2701548, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2701623, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False I've been searching this forum and other Linux-related forums for hours but I still have not found a solution. I mostly found advice on how to fix this when using an actual apple laptop or desktop, but I don't have that. They said to try something like the following echo 2 > /sys/module/hid_apple/ ... But since there's no hid_apple directory present on my systems, I've needed to modprobe hid_apple first. That didn't help either. I'm cool with changing some config files, or compiling my own patched kernel if that's necessary. I currently have a 10.04 and 12.04 system available to test. The same issue occurs when hooked up to Windows 7. Fn key still does nothing, not by itself or in combination with other keys. With some AutoHotkey fiddling, I was able to confirm the key is registered as pressed, but ignored by default. A custom AutoHotkey script can fix that. But AutoHotkey is only for Windows, I want my problem fixed on Linux. Hooked up to an iPad 2 it only works in combination with the F1-F12 keys. Not with the arrow keys. If the screen of the ipad is off, and I press just the Fn key, the screen will come on, so the key itself is registered as pressed. So to sum up my question: Can anyone help me get Page Up, Page Down, Home and End to work on this keyboard, when that requires me to use an Fn key which is currently not registered?

Read the article

Vista 64-bit, DISK BOOT FAILURE

- by weka

So I have this Acer Aspire AX3200-U3600A with Windows Vista (64-bit). Every night I turn it off and turn it back on in the morning. Around three weeks ago, I did a fresh factory reimage. Good as new. Then around two days ago, when I turned it on, I noticed it was running extremly slow. As in, it would often freeze up while I had multiple applications open when it usually never froze up. So I decided to restart my computer. Big mistake. My computer froze right after I clicked shut-down. I waited a while. Nothing. Waited some minutes. Nope. I decided to shut it down by pressing the power button. Here is where the problems begin. When I turned it back on, I saw the Windows logo and loading bar and then it loaded to black. I turned it off again forcefully by power button and then once more... then I got: AMD Data Change... Update New Data to DMI! then later the screen clears and I get: AHCI Option ROM BIOS Revision: 01.05.92 Date: 02-19-2008 Copyright (c) 2006-2008 Phoenix Technologies, LTD Port 01: Reset Port Error!! Port 02: then the screen clears again but this time, this loads from the bottom: Nvidia Boot Agent 249.0542 (copyright stuff... blah blah) PXE-E61: Media test failure, check cable. PXE-M0F: Exiting Nvidia Boot Agent DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER. So I try to go into Safe Mode. Well, first of all it doesn't load as fast. After it loads disk.sys from windows/drivers, it will wait a while (2-3 mins) THEN load. However it loads the Acer eRecovery Management Tool. I have three options: Reset computer to factory default, Restore computer from user's backup, or Exit. However, the top two options are gray and disabled where as the Exit is in blue and definitely clickable. So obviously safe mode is not there... A strong thing to note: In the beginning when all of this started, I did a Boot Windows Normal from pressing f8 and I got to my desktop! It logged me in. I could see the icons on my files. However my desktop was extremely slow as in when I clicked on the Start menu, it would wait a while, then load up the menu with JUST the gradient, no text or icons... so as you can see... it saw my HDD? Also, before anyone says, I have NO USB plugged in. My mouse and keyboard are not USB inputs, I assure you. And this came without a recovery CD AND when I went in BIOS, to change the BOOT ORDER, I did NOT see a CD-ROM option. And when I tried pressing ALT+F10 to get into Acer eRecovery Management, the top two options were disabled as well. But sometimes on start-up, I get: Windows has encountered a problem communicating with a device connected to your computer. This error can be caused by unplugging a removable storage device such as an external USB drive while the device is in use, or by faulty hardware such as a hard drive or CD-ROM drive that is failing. Make sure any removeable storage is properly connected and then restart your computer. If you continue to receive this error message, contact the hardware manufacturer. Status: 0xc00000e9 Info: An unexpected I/O error has occured. Then I tried Last Known Good Configuration Settings, that gives me a BSOD. What should I do/

Read the article

Trying to prevent Windows from hibernating/sleeping automatically

- by user328821

My Dell XPS 8700 (Win 7) suddenly began putting itself to sleep at 6pm daily, even if I'm typing. I don't know what caused this to occur, except possibly a windows update that took place in the middle of the night. I initially went into settings for power and saw 2 plans set up, one from Dell and the other window's Power saver plan. I set both to never for sleep and hibernate yet it still occurred. I have current drivers and a fairly new UPS that has software to set to shutdown only after power loss. Dell is of little help, can anyone point me in the right direction? I did do the powerdfg -energy program and came up with this: Power Efficiency Diagnostics Report Scan Time 2014-05-08T19:21:48Z Scan Duration 60 seconds System Manufacturer Dell Inc. System Product Name XPS 8700 BIOS Date 08/23/2013 BIOS Version A04 OS Build 7601 Platform Role PlatformRoleDesktop Plugged In true Process Count 115 Thread Count 1631 Report GUID {097caf99-039b-44c3-b154-d797bfbfdfcc} Analysis Results Errors Power Policy:Sleep timeout is disabled (Plugged In) The computer is not configured to automatically sleep after a period of inactivity. System Availability Requests:System Required Request The device or driver has made a request to prevent the system from automatically entering sleep. Requesting Driver Instance HDAUDIO\FUNC_01&VEN_10EC&DEV_0899&SUBSYS_102805B7&REV_1000\4&220b1bbc&0&0001 Requesting Driver Device Realtek High Definition Audio CPU Utilization:Processor utilization is high The average processor utilization during the trace was high. The system will consume less power when the average processor utilization is very low. Review processor utilization for individual processes to determine which applications and services contribute the most to total processor utilization. Average Utilization (%) 9.48 Warnings Platform Timer Resolution:Platform Timer Resolution The default platform timer resolution is 15.6ms (15625000ns) and should be used whenever the system is idle. If the timer resolution is increased, processor power management technologies may not be effective. The timer resolution may be increased due to multimedia playback or graphical animations. Current Timer Resolution (100ns units) 10000 Maximum Timer Period (100ns units) 156001 Platform Timer Resolution:Outstanding Kernel Timer Request A kernel component or device driver has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Request Count 2 Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Requesting Process ID 8672 Requesting Process Path \Device\HarddiskVolume3\Program Files (x86)\Mozilla Firefox\firefox.exe Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 100000 Requesting Process ID 1212 Requesting Process Path \Device\HarddiskVolume3\Windows\System32\svchost.exe Power Policy:802.11 Radio Power Policy is Maximum Performance (Plugged In) The current power policy for 802.11-compatible wireless network adapters is not configured to use low-power modes. CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name audiodg.exe PID 1304 Average Utilization (%) 4.73 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\msvcrt.dll 1.88 \Device\HarddiskVolume3\Windows\System32\MaxxAudioAPO5064.dll 1.77 \Device\HarddiskVolume3\Windows\System32\AudioEng.dll 0.80 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name thunderbird.exe PID 6036 Average Utilization (%) 0.35 Module Average Module Utilization (%) \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\xul.dll 0.16 \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\mozjs.dll 0.05 \SystemRoot\System32\win32k.sys 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name dwm.exe PID 1340 Average Utilization (%) 0.25 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\dwmcore.dll 0.08 \Device\HarddiskVolume3\Windows\System32\nvwgf2umx.dll 0.05 \SystemRoot\system32\ntoskrnl.exe 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace.

Read the article

Print directly to CUPS server from non-local clients (Ubuntu 14.04)

- by OEP

I set up a CUPS server with a few queues and printing from local clients (the CUPS test page and Samba) seems to work just fine. It seems like the CUPS server is denying non-local clients though: 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 390 Validate-Job successful-ok 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 339 Create-Job client-error-not-authorized localhost - - [03/Jun/2014:14:40:50 -0400] "POST /printers/m137 HTTP/1.1" 200 410869 Print-Job successful-ok This makes me think I have some sort of host-based restriction in my configuration file, but I can't find it. I've even set my default policy to Allow all only to get the same log message. I'm working from a configuration file which had previously worked on an older version of CUPS, which looks quite similar to the example cupsd.conf. I could be wrong but it looks like that final <Limit All> block ought to allow the actions the logs complain about. MaxLogSize 2000000000 # Log general information in error_log - change "info" to "debug" for # troubleshooting... LogLevel info #AccessLog syslog #ErrorLog syslog #PageLog syslog # Administrator user group... SystemGroup sys root lp # Only listen for connections from the local machine. Listen 0.0.0.0:631 Listen :::631 Listen /var/run/cups/cups.sock ServerName <snipped> # Show shared printers on the local network. Browsing Off BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order allow,deny Allow all </Location> # Restrict access to the admin pages... <Location /admin> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Set the default printer/job policies... <Policy default> # Job-related operations must be done by the owner or an administrator... <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order allow,deny </Limit> </Policy>

Read the article

Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

- by Eli

Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

Read the article

I have Oracle SQL Developer Installed, Now What?

- by thatjeffsmith

If you’re here because you downloaded a copy of Oracle SQL Developer and now you need help connecting to a database, then you’re in the right place. I’ll show you what you need to get up and going so you can finish your homework, teach yourself Oracle database, or get ready for that job interview. You’ll need about 30 minutes to set everything up…and about 5 years to become proficient with Oracle Oracle Database come with SQL Developer but SQL Developer doesn’t include a database If you install Oracle database, it includes a copy of SQL Developer. If you’re running that copy of SQL Developer, please take a second to upgrade now, as it is WAY out of date. But I’m here to talk to the folks that have downloaded SQL Developer and want to know what to do next. You’ve got it running. You see this ‘Connection’ dialog, and… Where am I connecting to, and who as? You NEED a database Installing SQL Developer does not give you a database. So you’re going to need to install Oracle and create a database, or connect to a database that is already up and running somewhere. Basically you need to know the following: where is this database, what’s it called, and what port is the listener running on? The Default Connection properties in SQL Developer These default settings CAN work, but ONLY if you have installed Oracle Database Express Edition (XE). Localhost is a network alias for 127.0.0.1 which is an IP address that maps to the ‘local’ machine, or the machine you are reading this blog post on. The listener is a service that runs on the server and handles connections for the databases on that machine. You can run a database without a listener and you can run a listener without a database, but you can’t connect to a database on a different server unless both that database and listener are up and running. Each listener ‘listens’ on one or more ports, you need to know the port number for each connection. The default port is 1521, but 1522 is often pretty common. I know all of this sounds very complicated Oracle is a very sophisticated piece of software. It’s not analogous to downloading a mobile phone app and and using it 10 seconds later. It’s not like installing Office/Access either – it requires services, environment setup, kernel tweaks, etc. However. Normally an administrator will setup and install Oracle, create the database, and configure the listener for everyone else to use. They’ll often also setup the connection details for everyone via a ‘TNSNAMES.ORA’ file. This file contains a list of database connection details for folks to browse – kind of like an Oracle database phoneboook. If someone has given you a TNSNAMES.ORA file, or setup your machine to have access to a TNSNAMES file, then you can just switch to the ‘TNS’ connection type, and use the dropdown to select the database you want to connect to. Then you don’t have to worry about the server names, database names, and the port numbers. ORCL – that sounds promising! ORCL is the default SID when creating a new database with the Database Creation Assistant (DBCA). It’s just me, and I need help! No administrator, no database, no nothing. What do you do? You have a few options: Buy a copy of Oracle and download, install, and create a database Download and install XE (FREE!) Download, import, and run our Developer Days Hands-on-Lab (FREE!) If you’re a student (or anyone else) with little to no experience with Oracle, then I recommend the third option. Oracle Technology Network Developer Day: Hands-on Database Application Development Lab The OTN lab runs on a A Virtual Box image which contains: 11gR2 Enterprise Edition copy of Oracle a database and listener running for you to connect to lots of demo data for you to play with SQL Developer installed and ready to connect Some browser based labs you can step through to learn Oracle You download the image, you download and install Virtual Box (also FREE!), then you IMPORT the image you previously downloaded. You then ‘Start’ the image. It will boot a copy of Oracle Enterprise Linux (OEL), start your database, and all that jazz. You can then start up and run SQL Developer inside the image OR you can connect to the database running on the image using the copy of SQL Developer you installed on your host machine. Setup Port Forwarding to Make It Easy to Connect From Your Host When you start the image, it will be assigned an IP address. Depending on what network adapter you select in the image preferences, you may get something that can get out to the internet from your image, something your host machine can see and connect to, or something that kind of just lives out there in a vacuum. You want to avoid the ‘vacuum’ option – unless you’re OK with running SQL Developer inside the Linux image. Open the Virtual Box image properties and go to the Networking options. We’re going to setup port forwarding. This will tell your machine that anything that happens on port 1521 (the default Oracle Listener port), should just go to the image’s port 1521. So I can connect to ‘localhost’ and it will magically get transferred to the image that is running. Oracle Virtual Box Port Forwarding 1521 listener database Now You Just Need a Username and Password The default passwords on this image are all ‘oracle’ – so you can connect as SYS, HR, or whatever – just use ‘oracle’ as the password. The Linux passowrds are all ‘oracle’ too, so you can login as ‘root’ or as ‘oracle’ in the Linux desktop. Connect! Connect as HR to your Oracle database running on the OTN Developer Days Virtual Box image If you’re connecting to someone else’s database, you need to ask the person that manages that environment to create for you an account. Don’t try to ‘guess’ or ‘figure out’ what the username and password is. Introduce yourself, explain your situation, and ask kindly for access. This is your first test – can you connect? I know it’s hard to get started with Oracle. There are however many things we offer to make this easier. You’ll need to do a bit of RTM first though. Once you know what’s required, you will be much more likely to succeed. Of course, if you need help, you know where to find me

Read the article

Oracle Enterprise Manager 12c Integration With Oracle Enterprise Manager Ops Center 11g

- by Scott Elvington

In a blog entry earlier this year, we announced the availability of the Ops Center 11g plug-in for Enterprise Manager 12c. In this article I will walk you through the process of deploying the plug-in on your existing Enterprise Manager agents and show you some of the capabilities the plug-in provides. We'll also look at the integration from the Ops Center perspective. I will show you how to set up the connection to Enterprise Manager and give an overview of the information that is available. Installing and Configuring the Ops Center Plug-in The plug-in is available for download from the Self Update page (Setup ? Extensibility ? Self Update). The plug-in name is “Ops Center Infrastructure stack”. Once you have downloaded the plug-in you can navigate to the Plug-In management page (Setup ? Extensibility ? Plug-ins) to begin deployment. The plug-in must first be deployed on the Management Server. You will need to provide the repository password of the SYS user in order to deploy the plug-in to the Management Server. There are a few pre-requisites that need to be completed on the Ops Center side before the plug-in can be deployed and configured on the desired Enterprise Manager agents. Any servers, whether physical or virtual, for which you wish to see metrics and alerts need to be managed by Ops Center. This means that the Operating System needs to have an Ops Center management agent installed as a minimum. The plug-in can provide even more value when Ops Center is also managing the other “layers of the stack”, for example the service processor, the blade chassis or the XSCF of an M-Series server. The more information that Ops Center has about the stack, the more information that will be visible within Enterprise Manager via the plug-in. In order to access the information within Ops Center, the plug-in requires a user to connect as. This user does not require any particular Ops Center permissions or roles, it simply needs to exist. You can create a specific “EMPlugin” user within Ops Center or use an existing user. Oracle recommends creating a specific, non-privileged user account within Ops Center for this purpose. From the Ops Center Administration section, select Enterprise Controller, click the Users tab and finally click the Add User icon to create the desired user account. For the purpose of this article I have discovered and managed the OS and service processor of the server where my Enterprise Manager 12c installation is hosted. With the plug-in deployed to the Management Server and the setup done within Ops Center, we're now ready to deploy the plug-in to the agents and configure the targets to communicate with the Ops Center Enterprise Controller. From the Setup menu select Add Targets then Add Targets Manually. Select the bottom radio button “Add Targets Manually by Specifying Target Monitoring Properties”, select Infrastructure Stack from the Target Type dropdown and finally, select the Monitoring Agent where you wish to deploy the plug-in. Click the Add Manually.... button and fill in the details for the new target using the appropriate hostname for your Enterprise Controller and the user and password details for the plug-in access user. After the target has been added to the agent you will need to allow a few minutes for the initial data collection to complete. Once completed you can see the new target in the All Targets list. All metric collections are enabled by default except one. To enable Infrastructure Stack Alarms collection, navigate to the newly added target and then to Target ? Monitoring ? Metric and Collection Settings. There you can click the “Disabled” link under Collection Schedule to enable collection and set your desired collection frequency. By default, a Warning level alert in Ops Center will equate to a Warning level event in Enterprise Manager and a Critical alert will equate to a Critical event. This mapping can be altered in the Metric and Collection Settings also. The default incident rules in Enterprise Manager only create incidents from Critical events so keep this in mind in case you want to see incidents generated for Warning or Info level alerts from Ops Center. Also, because Enterprise Manager already monitors the OS through it's Host target type, the plug-in does not pull OS alerts from Ops Center so as to prevent duplication. In addition to alert propagation, the plug-in also provides data for several reports detailing the topology and configuration of the stack as well as any hardware sensor data that is available. These are available from the Information Publisher Reports. Navigate there from the Enterprise ? Reports menu or directly from the Infrastructure Stack target of interest. As an example, here is a sample of the Hardware Sensors report showing some of the available sensor data. The report can also be exported to a CSV file format if desired. Connecting Ops Center to Enterprise Manager Repository For an Enterprise Manager user, the plug-in provides a deeper visibility to the state of the infrastructure underlying the databases and middleware. On the Ops Center side, there is also a greater visibility to the targets running on the infrastructure. To set up the Ops Center data collection, just navigate to the Administration section and select the Grid Control link. Select the Configure/Connect action from the right-hand menu and complete the wizard forms to enable the connection to the Enterprise Manager repository and UI. Be sure to use the sysman account when configuring the database connection. Once the job completes and the initial data synchronization is done you will see new Target tabs on your OS assets. The new tab lists all the Enterprise Manager targets and any alerts, availability and performance data specific to the selected target. It is also possible to use the GoTo icon to launch the Enterprise Manager BUI in context of the specific target or alert to drill into more detail. Hopefully this brief overview of the integration between Enterprise Manager and Ops Center has provided a jumpstart to getting a more complete view of the full stack of your enterprise systems.

Read the article

CDN on Hosted Service in Windows Azure

- by Shaun

Yesterday I told Wang Tao, an annoying colleague sitting beside me, about how to make the static content enable the CDN in his website which had just been published on Windows Azure. The approach would be Move the static content, the images, CSS files, etc. into the blob storage. Enable the CDN on his storage account. Change the URL of those static files to the CDN URL. I think these are the very common steps when using CDN. But this morning I found that the new Windows Azure SDK 1.4 and new Windows Azure Developer Portal had just been published announced at the Windows Azure Blog. One of the new features in this release is about the CDN, which means we can enabled the CDN not only for a storage account, but a hosted service as well. Within this new feature the steps I mentioned above would be turned simpler a lot. Enable CDN for Hosted Service To enable the CDN for a hosted service we just need to log on the Windows Azure Developer Portal. Under the “Hosted Services, Storage Accounts & CDN” item we will find a new menu on the left hand side said “CDN”, where we can manage the CDN for storage account and hosted service. As we can see the hosted services and storage accounts are all listed in my subscriptions. To enable a CDN for a hosted service is veru simple, just select a hosted service and click the New Endpoint button on top. In this dialog we can select the subscription and the storage account, or the hosted service we want the CDN to be enabled. If we selected the hosted service, like I did in the image above, the “Source URL for the CDN endpoint” will be shown automatically. This means the windows azure platform will make all contents under the “/cdn” folder as CDN enabled. But we cannot change the value at the moment. The following 3 checkboxes next to the URL are: Enable CDN: Enable or disable the CDN. HTTPS: If we need to use HTTPS connections check it. Query String: If we are caching content from a hosted service and we are using query strings to specify the content to be retrieved, check it. Just click the “Create” button to let the windows azure create the CDN for our hosted service. The CDN would be available within 60 minutes as Microsoft mentioned. My experience is that about 15 minutes the CDN could be used and we can find the CDN URL in the portal as well. Put the Content in CDN in Hosted Service Let’s create a simple windows azure project in Visual Studio with a MVC 2 Web Role. When we created the CDN mentioned above the source URL of CDN endpoint would be under the “/cdn” folder. So in the Visual Studio we create a folder under the website named “cdn” and put some static files there. Then all these files would be cached by CDN if we use the CDN endpoint. The CDN of the hosted service can cache some kind of “dynamic” result with the Query String feature enabled. We create a controller named CdnController and a GetNumber action in it. The routed URL of this controller would be /Cdn/GetNumber which can be CDN-ed as well since the URL said it’s under the “/cdn” folder. In the GetNumber action we just put a number value which specified by parameter into the view model, then the URL could be like /Cdn/GetNumber?number=2. 1: using System; 2: using System.Collections.Generic; 3: using System.Linq; 4: using System.Web; 5: using System.Web.Mvc; 6: 7: namespace MvcWebRole1.Controllers 8: { 9: public class CdnController : Controller 10: { 11: // 12: // GET: /Cdn/ 13: 14: public ActionResult GetNumber(int number) 15: { 16: return View(number); 17: } 18: 19: } 20: } And we add a view to display the number which is super simple. 1: <%@ Page Title="" Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<int>" %> 2: 3: <asp:Content ID="Content1" ContentPlaceHolderID="TitleContent" runat="server"> 4: GetNumber 5: </asp:Content> 6: 7: <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> 8: 9: <h2>The number is: <% 1: : Model.ToString() %></h2> 10: 11: </asp:Content> Since this action is under the CdnController the URL would be under the “/cdn” folder which means it can be CDN-ed. And since we checked the “Query String” the content of this dynamic page will be cached by its query string. So if I use the CDN URL, http://az25311.vo.msecnd.net/GetNumber?number=2, the CDN will firstly check if there’s any content cached with the key “GetNumber?number=2”. If yes then the CDN will return the content directly; otherwise it will connect to the hosted service, http://aurora-sys.cloudapp.net/Cdn/GetNumber?number=2, and then send the result back to the browser and cached in CDN. But to be notice that the query string are treated as string when used by the key of CDN element. This means the URLs below would be cached in 2 elements in CDN: http://az25311.vo.msecnd.net/GetNumber?number=2&page=1 http://az25311.vo.msecnd.net/GetNumber?page=1&number=2 The final step is to upload the project onto azure. Test the Hosted Service CDN After published the project on azure, we can use the CDN in the website. The CDN endpoint we had created is az25311.vo.msecnd.net so all files under the “/cdn” folder can be requested with it. Let’s have a try on the sample.htm and c_great_wall.jpg static files. Also we can request the dynamic page GetNumber with the query string with the CDN endpoint. And if we refresh this page it will be shown very quickly since the content comes from the CDN without MCV server side process. We style of this page was missing. This is because the CSS file was not includes in the “/cdn” folder so the page cannot retrieve the CSS file from the CDN URL. Summary In this post I introduced the new feature in Windows Azure CDN with the release of Windows Azure SDK 1.4 and new Developer Portal. With the CDN of the Hosted Service we can just put the static resources under a “/cdn” folder so that the CDN can cache them automatically and no need to put then into the blob storage. Also it support caching the dynamic content with the Query String feature. So that we can cache some parts of the web page by using the UserController and CDN. For example we can cache the log on user control in the master page so that the log on part will be loaded super-fast. There are some other new features within this release you can find here. And for more detailed information about the Windows Azure CDN please have a look here as well. Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

Search Results

Search found 2568 results on 103 pages for 'mup sys'.

Page 98/103 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 | Next Page >

- by Kapil Sharma

- by Matt

- by Tom Fishman

- by chrisbunney

- by Ole Tange

- by ARehman

- by Iain Elder

- by Wouter Vegter

- by tim

- by rima

- by Jakobud

- by user84207

- by Fabio

- by atomAltera

- by Taco Bob

- by hegemon

- by marc.riera

- by ramplank

- by weka

- by user328821

- by OEP

- by Eli

- by thatjeffsmith

- by Scott Elvington

- by Shaun

< Previous Page | 94 95 96 97 98 99 100 101 102 103 | Next Page >