Search Results

Search found 29159 results on 1167 pages for 'xml configuration'.

Page 986/1167 | < Previous Page | 982 983 984 985 986 987 988 989 990 991 992 993  | Next Page >

• wireless clients not getting correct dhcp addresses

  - by szeli

  I apologise first if this is a stupid problem. I'm new to Cisco networking. I need some help with an existing configuration done by my vendor. Environment: 1. Core switch - Catalyst 6509e vlans configured: a. vlan 50 (wired clients) 10.0.50.x/24 interface IP 10.0.50.20 b. vlan 70 (wireless clients) 10.0.70.x/24 interface IP 10.0.70.20 c. vlan 192 (guest clients) 192.168.1.x/24 interface IP 192.168.1.20 d. trunk port for WLC native vlan 70 allowed vlan 50, 70, 192 2. Cisco 4402 WLC interfaces a. management untagged IP 10.0.70.10 b. ap-manager untagged IP 10.0.70.11 c. service-port n/a IP 192.168.10.1 d. virtual n/a IP 1.1.1.1 e. guestwlan vlan192 IP 192.168.1.100 3. Cisco AIR-LAP1142N-S-K9 LAP01 (WLAN local, interface: management) IP 10.0.70.21/24 GW 10.0.70.20 DHCP server 10.0.50.10 (scope 10.0.70.101 to 200) LAP02 (WLAN guest, interface: guestwlan) IP 192.168.1.21/24 GW 192.168.1.20 DHCP server 192.168.1.10 (scope 192.168.1.101 to 200) here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200) can anyone please help? thanks!

  Read the article

• Should I be able to Windows Phone 8 emulator running with this AMD config

  - by pete

  I have just bought a new system as follows * AMD A4-5300 Trinity 3.4GHz * Gigabyte GA-F2A55M-DS2 Motherboard I checked and the A4-5300 supports Virtualisation. I have run the SLAT checking tool and it says that my machine supports SLAT. Been into the BIOS and ensures that SVN is enabled. I have also run the coreinfo tool that indicates that SVN is not valid fort the machine nor is NPT.. not sure why this conflicts with the true BIOS setting (I checked with GIGABYTE and seems that NPT and NX are not options that can be set in the BIOS) But.. when I run the emulator I it hangs - I can see some activity in Hyper-V manager, but it doesnt get very far and no meaningfull error messages. Been working the plethora of suggestions to get around this, but so far, nothing has worked. My question is should this setup allow the WP8 emulator to run. I am positive the CPU supports virtualisation, but are there issues with the motherboard here? I have spent a huge amount of time on this so far....am I wasting my time with the current configuration, or should it work? thanks

  Read the article

• Server taking too long to respond error

  - by DCJones

  Hi, This is my first post on serverFault and my first entry in to web server configuration. The hardware and software. CPU: GenuineIntel, Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz OS: Linux 2.6.18-128.el5 Memory: 2Gb Background. I am running a small database (MySQL), around 1000 records with each record containing 44 fields. At the start of each day “00:01” the tables are cleared and populated with fresh data. The are 10 remote PCs all running Winodws XP and Firefox internet browser. All remote PC’s are connected to the internet using a min 4Gb broadband connection. Each remote PC runs a URL which displays a dynamic page of data which is refreshed every 20 seconds. This is a continual process 24 hours a day. I problem I am having is on odd occasions throughout the day the PC browser error with “Server taking too long to respond error”. What I am trying to find our is if I have the correct setting in the httpd.conf file on the server. Any help or advice anyone can provide would be very helpful. Best regards Dereck Server config file: httpd.conf ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 5 StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 254 MaxRequestsPerChild 4000 StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 MaxRequestsPerChild 0

  Read the article

• Is there an simple but good To Do Manager app for the Mac?

  - by Another Registered User

  Every morning I think about what I am going to do today. So I take a paper and start to write things like: [ ] Call Mr. XYZ [ ] Answer Support E-Mails [ ] Reduce website header height by 20 px [ ] Create new navigation bar icons And every time I'm done with something, I paint a checkmark in this square. On paper. It would be fun to have something like this as an application. But I don't want a heavy project management tool or integration with email. It should be like download, install, use without fat configuration and steep learning curve. usually I don't schedule my to do's, I just write down every day what I want to accomplish today. For my experience it doesn't make sense to plan what to do next week, because next week everything looks totally different. Would be cool if such a simple utility exists. At the moment I try just using textEdit and deleting rows which are done. With a nice interface, this would be much more fun.

  Read the article

• How to reliably mount a shared folder /volume/folder at boot up

  - by Tanmay

  Following is my sample.sh in /usr/local/bin/ #!/bin/sh mkdir -p /Volumes/folder mount -t afp -o rw afp://user:password@server_name/folder_name /Volumes/folder Following is my com.apple.sample.plist in /Library/LaunchAgents/ ?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>com.apple.sample</string> <key>ProgramArguments</key> <array> <string>/usr/local/bin/sample.sh</string> </array> <key>RunAtLoad</key> <true/> </dict> </plist> Where as when I am able to run sample.sh independently and is working fine. Also I have tried using launchd.conf as mkdir -p /Volumes/folder mount -t afp -o rw afp://user:[email protected]/testsuites /Volumes/folder Still not working.

  Read the article

• Windows Server 2008 R2 grinds to a screeching halt during file copy operations

  - by skolima

  When my Windows Server 2008 R2 machine is performing any large disk operations (copying 10GB files from one drive to another, copying similar file over network, merging HyperV snapshots, compressing large files), performance of the whole machine slows down terribly, everything becomes unresponsive. This is noticeable in any situation when the disk access is large enough not to fit in the cache. Are there any settings available for tuning this behaviour? I can accept slower file transfer if this would give me more responsiveness. System details: Dell Optiflex 960, Core 2 Quad Q9650, 8GB RAM, 2 SATA drives - 320GB (ST3320418AS) and 1TB (ST31000528AS), NCQ active on both, Intel 82564LM-3 Gigabit Ethernet, ATI HD 3450 graphics, Intel ICH10 bridge. We have multiple machines like this, every one is exhibiting the same behaviour. I though this was overkill for a workstation, apparently I was mistaken. Update: I guess I shouldn't have mentioned the HyperV at all. The above configuration is a standard workstation setup at the company I work for, this is not a server of any kind. I have at most 3 virtual machines working, and usually I'm the only person accessing them. Never the less, the slowdown occurs even when no VMs are running. On a Linux machine I'd simply ionice the copy process and I could forget about it, is there any way to manage IO priorities on Windows?

  Read the article

• cpusets not working - threads aren't running in the cpuset I specified?

  - by lori

  I have used cpuset to shield some cpus for exclusive use by some realtime threads. Displaying the cpuset config with the test app RealtimeTest1 running and its tasks moved into the cpusets: $ cset set --list -r cset: Name CPUs-X MEMs-X Tasks Subs Path ------------ ---------- - ------- - ----- ---- ---------- root 0-23 y 0-1 y 279 2 / system 0,2,4,6,8,10 n 0 n 202 0 /system shield 1,3,5,7,9,11 n 1 n 0 2 /shield RealtimeTest1 1,3,5,7 n 1 n 0 4 /shield/RealtimeTest1 thread1 3 n 1 n 1 0 /shield/RealtimeTest1/thread1 thread2 5 n 1 n 1 0 /shield/RealtimeTest1/thread2 main 1 n 1 n 1 0 /shield/RealtimeTest1/main I can interrogate the cpuset filesystem to show that my tasks are supposedly pinned to the cpus I requested: /cpusets/shield/RealtimeTest1 $ for i in `find -name tasks`; do echo $i; cat $i; echo "------------"; done ./thread1/tasks 17651 ------------ ./main/tasks 17649 ------------ ./thread2/tasks 17654 ------------ Further, if I use sched_getaffinity, it reports what cpuset does - that thread1 is on cpu 3 and thread2 is on cpu 5. However, if I run top -p 17649 -H with f,j to bring up the last used cpu, it shows that thread 1 is running on thread 2's cpu, and main thread is running on a cpu in the system cpuset (Note that thread 17654 is running FIFO, hence thread 17651 is blocked) PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ P COMMAND 17654 root -2 0 54080 35m 7064 R 100 0.4 5:00.77 3 RealtimeTest 17649 root 20 0 54080 35m 7064 S 0 0.4 0:00.05 2 RealtimeTest 17651 root 20 0 54080 35m 7064 R 0 0.4 0:00.00 3 RealtimeTest Also, looking at /proc/17649/task to find the last_cpu each of its tasks ran on: /proc/17649/task $ for i in `ls -1`; do cat $i/stat | awk '{print $1 " is on " $(NF - 5)}'; done 17649 is on 2 17651 is on 3 17654 is on 3 So cpuset and sched_getaffinity reports one thing, but reality is another I would say that cpuset is not working? My machine configuration is: $ cat /etc/SuSE-release SUSE Linux Enterprise Server 11 (x86_64) VERSION = 11 PATCHLEVEL = 1 $ uname -a Linux foobar 2.6.32.12-0.7-default #1 SMP 2010-05-20 11:14:20 +0200 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Domain joining debate for Outlook 2010 with Exchange 2007 on windows SBS 2008 for a user on a laptop that will travel a fair amount of the time.

  - by user71195

  I'm basically debating on whether or not to join the Domain on a Laptop, and was wondering if anyone has had a similar experience. If the computer were staying in the office, its a no brainer. Join the domain. In this case I have a user who will come into the office a few days a week, and work remotely the rest of the time. There is a working VPN using OpenVPN client/server, but it's not site-to-site. My knee jerk reaction is to not join the domain, so that the user can have 1 profile that they always use. In this configuration, should Outlook work properly with the user's domain account, and should the shared calendar still work (at least once inside the VPN)? My concern with joining the domain would be the inability to login to it when elsewhere. Is there maybe a way around this with caching or something? Would creating a second local login make sense for a user like this in any way? If so, why not just skip the domain join to begin with? Any thoughts on or experiences with this would be appreciated. Laptop OS Windows 7 (Not purchased yet.. pro if domain needed) Server SBS 2008, Exchange 2007 Outlook version 2010 Thanks for any help, Mike

  Read the article

• Trying to diagnose network problem: ping 127.0.0.1 (or any address) results in error code 1

  - by Mnebuerquo

  NIC seems to be working, as windows detects the hardware and has a driver and reports success. DHCP seems to have gotten an ip address, 192.168.1.101. I released and renewed it and it seemed to work normally. I tried ping 127.0.0.1 as first step of testing network configuration. Pinging 127.0.0.1 with 32 bytes of data: PING: transmit failed, error code 1. I read somewhere that net helpmsg [error code] would give a human readable name for the error code. net helpmsg 1 says "Incorrect function" I've tried disabling the firewall and antivirus in McAfee SecurityCenter and I still get the same error. Could the firewall/antivirus be breaking it even if disabled? Broadcom Advanced Control Suite 2 is installed, and its network test passes all tests, including ping 192.168.1.1 which is the default gateway. If I try ping 192.168.1.1 from the command prompt I get the error code 1 again. So does anyone have any theories that would explain this problem? Other tests I should try? Thanks!

  Read the article

• Migrate active directory to Google apps for business

  - by dewnix

  I've got a problem migrating active directory to Gapps. I'm stuck on google apps directory sync (GADS) where it just gives the error "java.lang.NullPointerException" after testing the connection during the LDAP configuration step. I checked the logs and I've pretty much determined that port 389 (standard LDAP port) isn't listening on the exchange server. I've tried telneting to it (from another machine in the same network) with no luck but I can telnet to other ports, that i know are open, successfully. I know they're open because I used portqry and netstat to see them. I'm suspecting that the active directory isn't even installed/running on this machine because there's no active directory services at all running on it. There's no active directory services that say they're NOT running either though. Is it possible AD is installed somewhere else? does it have to be on a machine inside the same network? I found the domain controller and it's host name and when I telnet with port 389, it works however GADS still gives me the same exact error when I substitute that server in. Actually, no matter what ridiculous settings i put into GADS, i still get that same NullPointer error. If i could get some different error than that NullPointer, i'd call that a successful day.

  Read the article

• using nginx with proxy_pass on a subdomain

  - by marcus3006

  a have a rails app that should listen on the subdomain redmine.example.com (using proxy_pass). all other requests for *.example.com should just redirect to a normal index.html. Here is my configuration: server { server_name www.example.com example.com; root /home/deploy/static/example; } upstream redmine { server unix:/tmp/redmine.socket fail_timeout=0; } server { # you could put a list of other domain names this application answers server_name redmine.example.com; root /home/deploy/rails/redmine/public; access_log /var/log/nginx/redmine_access.log; rewrite_log on; location * { proxy_pass http://redmine; } location ~ ^/(assets)/ { root /home/deploy/rails/redmine/public; gzip_static on; # to serve pre-gzipped version expires max; add_header Cache-Control public; } } anyone knows what's going wrong here? requests to example.com and www.example.com are handled correctly. when i try to acces redmine.example.com = "couldn't resolve host"

  Read the article

• Identifying test machines in analytics logs

  - by RTigger

  We're just beginning to add analytics to our SaaS application, to begin (among other things) billing clients based on usage. The problem we're running into is there's a few circumstances where our support team will simulate a log in into production to try to reproduce reported issues with a client's configuration. When they log in, an entry will be made into our analytics logs that their specific account has logged in, which we use to calculate billing. A few ideas we had to solve this: 1) We log IP addresses as well as machine keys for each PC that logs in - we could filter out known IP addresses and/or machine keys belonging to support. The drawback is we have to maintain a list of keys / addresses manually. 2) If support (or anyone else internal) runs our application in debug mode (as opposed to release), it will not report analytics. This is fine, as long as support / anyone else remembers to switch to debug mode. 3) Include some sort of reg key / similar setting required to be set when configuring a production system in order to send analytics. Again, fine, as long as our infrastructure team remembers to set the reg key or setting. All of these approaches require some sort of human involvement, which we all know can be iffy at best. Has anyone run into a similar situation? Is there an automated approach to this problem? (PS Of course, we shouldn't be testing in production, but there are a few one-off instances with customer set up that we can't reproduce without logging in as them in production. This is the only time we do so, and this is the case I'm talking about in this question.)

  Read the article

• Conflicts with file from package mysql-5.0.77

  - by Whiteyq

  I'm trying to install APC (Alternative PHP Cache) on a CentOs dedicated server. I've everything done apart from configuring phpize. Running :yum -y install php-devel gives me the following error file /usr/share/mysql/charsets/Index.xml from install of mysql-libs-5.1.57-1.el5.art.x86_64 conflicts with file from package mysql-5.0.77-4.el5_5.3.i386 etc etc for other languages So, i think the mysql version i have is too old & i more than likely need to upgrade mysql to version 5.1. Im reluctant to do this as a) its a live server (although only 3/4 domains) b) ive read ill read to recompile php if i upgrade To add to this i have plesk installed for managing domains & might need reinstalling/reconfiguring also. sorry for the long intro but its my first post & best to give as much info as possible, so my question is basically Is there any way i can run :yum -y install php-devel to get phpize working to complete installation of APC for the version of mysql i currently have installed? ie 5.0.77

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• How should I configure my Apache Hosts File to serve a different site for localhost than for my domain/publicip?

  - by rofls

  I'm trying to test out a LAMP (with PHP5 specifically) setup with Django already serving a website. I want to do the PHP stuff on localhost for now, so that when I do something like this: curl http://localhost/database/script.php?var=1, I get a response from the php server. Right now I'm getting a Django error. I tried something like this in the default file in sites-available: Listen 80 <VirtualHost aaa.bbb.ccc.ddd> ServerName localhost DocumentRoot /home/phpsite </VirtualHost> where aaa.bbb.ccc.ddd is the local ip address, and changing my actual site's settings to specify the public ip, like this: Listen 80 <VirtualHost www.xxx.yyy.zzz> ServerName mysite.com DocumentRoot /srv/www/mysite WSGIScriptAlias / /srv/www/mysite.wsgi </VirtualHost> but then I start getting all kinds of errors when I start apache, such as port ::[80] is already in use or something. I noticed that the hosts file that's located in /etc/apache2/ is apparently pointing everything to mysite.com, including my local ip as well as 127.0.0.1 and 127.0.1.1; Do I need to change the configuration there too?

  Read the article

• PHP Web Server Solution (Apache/IIS)

  - by njk

  I apologize if this is too broad or belongs on Super User (please vote to move if it does). I'm in the process of creating requirements for an internal PHP web server to submit to our architecture team and would like to get some insight whether to use a Windows or *nix platform and what applications would be required. The server will host a small PHP application that will be connecting to SQL Server. The application will need to send mail. We would also like to incorporate a FTP server to allow files to be dropped in. From what I've read regarding a Windows platform using IIS, it seems as though IIS would only be advantageous if using a .NET or ASP application. Does IIS have mail functionality? Or how is mail traditionally configured (esp. on *nix)? Also, does IIS have directory configuration functionality like Apache does with .htaccess? For a Windows based solution; IIS (comes with FTP) Apache (has mod_ftp module) For a *nix based solution; Apache

  Read the article

• Issues with returned mail sent to web-based email domains

  - by Beeder

  My company is having issues with returned mail that we send out to external domains. A few weeks ago we replaced a firewall and changed ISP providers and began subsequently having issues RECEIVING emails from external sources because we hadn't updated our new IPs in the DNS records. After making the necessary configuration changes and setting up SMTP forwarding over port 25 to our mail server, everything was working fine up until a few days ago when we started having mail sent out returned to us. We aren't having any trouble communicating internally (to recipients on our domain) but it seems we're having trouble with outbound messages to web-based email recipients. (@hotmail, @live, @yahoo, @gmail...etc) Currently we are running Server 2003 SP2 and exchange 2003. I'm very unfamiliar with configuring Exchange and could really use some help in narrowing down the possibilities. I did some research and am becoming suspicious of Sender ID being the culprit due to our recent IP address change and the likelihood that Sender ID is identifying us as a fake domain. Am I going in entirely the wrong direction? Any input or guidance would be infinitely appreciated. This is the message that is returned when an outbound message fails...this particular one was sent to my @live.com account for testing purposes... Your message did not reach some or all of the intended recipients. The following recipient(s) could not be reached: [email protected] on 5/17/2012 3:02 PM There was a SMTP communication problem with the recipient's email server. Please contact your system administrator. Unfortunately, messages from xx.x.xx.x weren't sent. Please contact your Internet service provider since part of their network is on our block list. I tried a reverse DNS lookup and found that we are set up as a Forward-confirmed reverse DNS. So do I just need to contact my ISP and have them correct their DNS records or is this something I can solve on our end??

  Read the article

• Gnome 3 application Icons disappeared

  - by robin.koch

  I edited my main menu settings (unchecked items inside a sub menu) when it happened that the window freezed and all entries on the left side disappeared (Office, System, Settings, Games, ...). I didn't think much about it, but when I restarted my computer all application entries in my menu and my favorites (quickstart bar on the left side) where gone. When I go to activities - applications I just see the "All" entry without any items to click on. ~/.config/menu/gnome-applications.menu is an empty file and ~/.config/menu/gnome-settings.menu has the folowing content: <!DOCTYPE Menu PUBLIC '-//freedesktop//DTD Menu 1.0//EN' 'http://standards.freedesktop.org/menu-spec/menu-1.0.dtd'> <Menu> <Name>Desktop</Name> <MergeFile type="parent">/etc/xdg/menus/gnome-settings.menu</MergeFile> </Menu> I also looked into the files under /etc/xdg/menus. They look like template files without any reference to actual installed programs. I assume that due to a bug it deleted all my menu settings. Is there any way to restore at least the default menu? Or are there any other places to look for my old configuration?

  Read the article

• Plesk command working in manual script, not in cronjob

  - by dsaunier

  Hi, In order to install a hosting plan, I use Plesk's commands in SSH as specified in their official guide. When typed directly in SSH (Putty), it works perfectly. The line is as follows with obviously values hard coded when in CLI: /usr/local/psa/bin/domain --create '.$url.' -owner mynamehere -ip '.IP_SERVER_PLESK.' -status enabled -hosting true -hst_type phys -login '.$ftp_user.' -passwd '.$ftp_pw.' -www false -php true -php_safe_mode false -hard_quota 100M I then put that request in a php script that does other things after hosting is installed. Now for the weird part: when calling that script from CLI it also works fine, I do a ./myscript.php and it installs the hosting, then sends emails etc. However after I create a cronjob to have that same script called regularly, then the Plesk command fails. The cronjob is started in Plesk as */15 * * * * /usr/bin/php /home/scripts/myscript.php and it works fine for everything BUT the Plesk hosting install, that returns "Unable to read Control Panel configuration file" and therefore does not install the domain hosting. Still this is the same script that I call manually ! On that server are the PHP used to call a cronjob and the one used in CLI different ? What do I miss, help greatly appreciated ! Regards.

  Read the article

• Changing farm account in Sharepoint 2010

  - by user55709

  After changing the the farm account to a domain user account I get the following error when trying to access the Central Administration page: "Cannot connect to configuration database" After I realized the headache may not be worth it, I decided to a reinstall using the following SP user account guidelines: http://technet.microsoft.com/en-us/library/ee662513.aspx After getting everything up, I am getting an error when using the designated farm account under the Central Admin Website Manage Service Accounts: "Access denied" If it is the farm administrator, why would I not be able to manage service accounts? I am able to access the other part of the admin site. Also, when logging in with the farm account it lists me as a "system account" not the domain account which I used for log in. Am I missing something or is this normal behavior? Am I not suppose to login with the farm account? When I log in with the Setup account (also a domain account) I can access everything with no errors on the site. The only difference between the two accounts is one has local admin privileges on the Sharepoint farm server which is the setup account. if you notice those privileges are not necessary for the farm account according to the article cited.

  Read the article

• MSSQL 2008 login failed for windows authentication

  - by Force Flow

  I'm running Microsoft SQL 2008 on a Windows 2008 Server. The MSSQL server server authentication is set to SQL Server and Windows Authentication mode. I have created an active directory security group "xyz app users". I have added a normal user (without any active directory admin privledges) and a user with domain admin privledges to the "xyz app users" group. I have added the group to the MSSQL management console as a login user. This group is a member of the public server role and is mapped to two databases. On a workstation, when the normal user is logged in, I configure a DSN ODBC connection, and I'm able to successfully create the DSN and test the SQL connection. However, when I'm logged in as the user with domain admin privledges, when I attempt to configure the DSN ODBC connection, I can't get past the login ID configuration screen. If I select "windows authentication" and click "next", I get an error: Connection failed: SQLState: '28000' SQL Server Error: 18456 [Microsoft][ODBC SQL Server Driver][SQL Server]Login failed for user 'mydomain\myuser' On the server's application event logs, this error appears: Login failed for user 'mydomain\myuser'. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: 172.x.x.x] And in MSSQL's event logs: Error: 18456, Severity: 14, State: 11 Solutions that I've seen so far do not seem to fit this situation (some solutions I've seen are only applicable when the BUILDIN\Administrator is being used locally on the server, which is not the case here).

  Read the article

• Random HTTP 413 error on apach2/php/joomla site

  - by jfab

  I have a Joomla site, and every once in a while when I submit something via a form, I get a HTTP 413 error: Request Entity Too Large The requested resource /index.php does not allow request data with POST requests, or the amount of data provided in the request exceeds the capacity limit. In the error.log file I get: Invalid Content-Length, referer: [site]/index.php It doesn't seem this has anything to do with the actual size of the request, for the following reasons: a) I tinkered with the configuration of both Apache, and PHP. In Apache I tried increasing LimitRequestBody, and in PHP post_max_size, max_input_vars, memory_limit, and even upload_max_filesize. Every value is far beyond what is sent in a typical request that generates an error. b) The error pops up quite randomly, and often just hitting refresh allows me to get through. c) I checked the request in Fiddler to make sure everything is right with the content-length stated in the header, and the content of the request itself. Everything appears to be in order. A curious thing is that when I resent the exact same request via Fiddler, I never got the error. It seems I can only recreate it through a browser. So I'm at my wit's end here. I don't even know where to look for the problem anymore. I don't know if it's Apache or PHP (though I can't find anything in PHP error logs, so maybe that means Apache is the more likely culprit?), or PHP in general, or my Joomla site in particular (my bets were on Joomla until a recreated the error on a test script, with a very basic post form, though it does pop up much more often on the Joomla site). If anyone can give any advice on where to even begin with this, I'll be very grateful!

  Read the article

• Locate devices within a building

  - by ams0

  The situation: Our company is spread between two floors in a building. Every employee has a laptop (macbook Air or MacbookPro) and an iPhone. We have static DHCP mappings and DNS resolution so every mobile gets a name like employeeiphone.example.com, every macbook air gets a employeelaptop.example.com and every macbook pro gets a employeelaptop.example.com on the Ethernet interface (the wifi gets a dynamic IP from a small range dedicated for the purpose). We know each and every MAC address of phones and laptops, since we do DHCP static mapping (ISC DHCP server runs on linux). At each floor we have a Netgear stack of two switches, connected via 10GB fiber to each other. No VLANs so far. At every floor there are 4 Airport Extreme making a single SSID network with WPA2 authentication. The request: Our CTO wants to know who is present at which floor. My solution (so far): Every switch contains an table listing MAC address and originating port. On each switch stack, all the MAC addresses coming from the other floor are listed as coming on port 48 (the fiber link). So I came up with: 1) Get the table from each switch via SNMP 2) Filter out the ones associated with port 48 3) Grep dhcpd.conf, removing all entries not *laptop and not *iphone 4) Match the two lists for each switch, output in JSON or XML 5) present the results on a dashboard for all to see I wrote it in bash with a lot of awk and sed, it kinda works but I always have for some reason stale entries in the switch lookup tables, making it unreliable; some people may have put their laptop to sleep, their iphones drop connections after a while, if not woken up and so on..I searched left and right, we are prepared to spend a little on the project too (RFIDs?), does anybody do something similar? I can provide with the script if needed (although it's really specific to our switches and naming scheme). Thanks! p.s. perhaps is this a question for stackoverflow? please move if it so.

  Read the article

• How to "open" existing VMs in Hyper-V without importing them?

  - by Borek

  I had a PC with two physical disks: C: containing the host operating system D: containing a folder D:\VMs where all my virtual machines were stored Now, the C: disk died. I bought a new one, reinstalled Windows on it, enabled Hyper-V feature and now I just need to open the VMs from the D:\VMs folder. However, I don't seem to be able to find a menu item or anything that would allow me to do that - the only thing I see is the "import" command which unfortunately requires the VMs to be explicitly exported (my machines weren't). I firmly believe that when I have all the files constituting a VM (the VHD file, some XML files describing the settings etc.) it must be somehow possible to just "open" these existing VMs in Hyper-V, right? What command am I missing? Edit: I know I can create a blank virtual machines and then just point them to use existing VHDs. However, I am not sure about all the different settings I've made to those VMs so I hope there's a way to simply open those existing VMs instead of recreating them.

  Read the article

• Route all traffic of home network through VPN

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

< Previous Page | 982 983 984 985 986 987 988 989 990 991 992 993  | Next Page >