Search Results

Search found 8937 results on 358 pages for 'disk defragmenting'.

Page 99/358 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• How to rescue from an SD (SDHC) card that I can't reformat (possible hardware failure)

  - by sbwoodside

  I have a transcend 16GB SDHC card and a lot of photos on it that I'd like to recover. When I plug it into the SD card reader, it takes a while for the Mac to even recognize that there's a disk present, and it shows up as 1.07GB with geometry 520/64/63 (according to fdisk). First I tried file recovery: PhotoRec: no files are found (the images are in CR2 format and I'm using testdisk-6.14-WIP which claims to recognize that format under TIF) dd / ddrescue: they create a 1.07GB image, same problem as above TestDisk: doesn't find any partitions to recover I found a source saying that the correct geometry for this type of SD Card is Heads 255, Sectors/Track 63, Cylinders 1953, so I tried manually setting that geometry in PhotoRec/TestDisk. No improvement. Next I tried formatting the disk with fdisk. After writing and quitting, I ran fdisk again and it reported that the new format hadn't been saved on the disk. I also tried resetting the format/partitions with TestDisk and that failed also. The fdisk log is below. I don't really care about the card, I've already ordered a new SanDisk card. But I'd like to get the data off. Maybe, is there any way to force dd or some other tool to create an image of the disk based on the original geometry and not on what the card "thinks" its geometry is? Or am I missing something?

  Read the article

• how to uninstall ubuntu 8 from ubuntu 10 dual boot

  - by umar

  I have ubuntu 8.04 and ubuntu 10.04 on my laptop, and i want to reclaim all the ubuntu 8 space so that i have just one operating system on my laptop. how can i do it? the output of sudo fdisk -l is as follows: sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x31a431a3 Device Boot Start End Blocks Id System /dev/sda1 * 1 4959 39833136 83 Linux /dev/sda2 4960 5233 2200905 82 Linux swap / Solaris /dev/sda3 5234 12852 61192552 83 Linux /dev/sda4 12852 19458 53062657 5 Extended /dev/sda5 12852 19182 50847744 83 Linux /dev/sda6 19182 19458 2213888 82 Linux swap / Solaris i dont know which of sda1, ..., sda 6 etc ubuntu 8 is on. how can i find that out? The actual task is that i think a lot of space is devoted to ubuntu 8, if there is no easy way to get rid of it, then i want to repartition the disk so that about 50 GB of hard disk space is given to ubuntu 10's home folder from the ubuntu 8's home folder. but i hope that there is an easy way to get rid of ubuntu 8 alrogether and just have ubuntu 10 on my system.

  Read the article

• Dual boot nt4 and windows 98

  - by ItFinallyWorks

  I am trying to dual boot nt4 and windows 98 se (don't laugh - old computer). I have seen Microsoft's instructions for doing this, but it limits windows 98 to have a Fat16 partition (NT4's NTLDR doesn't understand FAT32) and therefore only 2GB of disk space. I really need it to have more than that. I started with Win 98 (on the 1st partition), repartitioned the disk, then added NT4 on the 2nd partition. NT4 took over the bootloader (as expected), so NT4 boots, but Win 98 doesn't. Right now I am working in VMWare so I can use nonpersistent hard drives (IDE like the real computer) to recover from errors easily. I've tried using XPs NTLDR using the instructions here: http://www.nu2.nu/fixnt4/ , but I got weird errors from NT4 and it never really worked. If XP's NTLDR would work, that should be able to boot both OSes. I've also tried using GRUB. In theory that should work. In fact when booting from super grub disk, it does. But as soon as I install grub to disk, Win 98 boots, but NT 4 blue screens at boot with a 0x0000007b inaccessible_boot_device error (that can be alot of things see MS kb 822051). The incantation I'm using for GRUB 1 is rootnoverify (hd0,1) makeactive chainloader +1 boot So, anybody have some suggestions?

  Read the article

• Creating Windows 8.1 system image error

  - by Random

  I'm experiencing "not enough space" error when trying to create system image to a USB hard drive: Detailed error: ERROR - A Volume Shadow Copy Service operation error has occurred: (0x8004231f) Insufficient storage available to create either the shadow copy storage file or other shadow copy data. Blah, blah... There is not enough disk space to create the volume shadow copy on the storage location. Make sure that, for all volumes to be backup up, the minimum required disk space for shadow copy creation is available. This applies to both the backup storage destination and volumes included in the backup. Minimum requirement: For volumes less than 500 megabytes, the minimum is 50 megabytes of free space. For volumes more than 500 megabytes, the minimum is 320 megabytes of free space. Recommended: At least 1 gigabyte of free disk space on each volume if volume size is more than 1 gigabyte. ERROR - A Volume Shadow Copy Service operation error has occurred: (0x8004231f) Insufficient storage available to create either the shadow copy storage file or other shadow copy data. I'd tried both - PowerShell wbAdmin start backup -backupTarget:E: -include:C: -allCritical -quiet and via Control Panel - File History button Clearly both EFI and Windows Recovery Environment partitions don't meet requirements coming from System Image tool (pic below) On top of that all system partitions are now shown as 100% free in Disk Management, it's disturbing but far from the actual state. My question is - hot to create System Image in Windows 8.1?

  Read the article

• Data recovery on a data HDD (no OS)

  - by aCuria

  I am helping a family member with a dead hard disk. It is a seagate 200Gb 3.5" HDD in one of those old-school external enclosures. The problem was that windows failed to detect the hard disk when plugged in through USB. I removed the hard disk from its enclosure, and plugged it into my desktop PC. The BIOS does detect it upon POST, but unfortunately windows 7 would refuse to boot. It will get stuck on the loading screen with the glowing windows logo. Safe mode doesn't help either. What options do I have before going for some professional data recovery? edit: Someone modified the Title to something completely different from what I was asking, i just changed it back. 1) 2 HDD drives, DiskA(Dead), DiskB(my OS disk) 2) when B is connected to my system, everything works fine 3) when A AND B is connected, failure to boot. POSTs fine, but windows wont load 4) A has NO OS, its PURE data. It came from an EXTERNAL HDD enclosure which doesnt belong to me, and im trying to do data recovery.

  Read the article

• Windows won't sleep after booting from grub

  - by mkasberg

  I recently added a second hard drive to my computer and I am using it do dual-boot Linux (Ubuntu 12.04) with Windows 7. Both hard drives are SATA. I am using the default grub bootloader on my second hard drive. The windows drive is unmodified. To get to grub, I changed the hard disk boot priority in my BIOS (P35-DS3L) to boot from the second drive. The problem I'm having is that when I boot to Windows 7 (on sda) from grub (on sdb), Windows 7 will not go to sleep (from the start menu). The display shuts off momentarily as if its going to sleep, then comes back on and displays the switch-user screen. Powercfg -lastwake does not show anything. I am sure that this is related to booting from grub on sdb because when I change the hard disk boot priority in the BIOS to boot from my (unmodified) Windows hard disk, the computer goes to sleep fine. It occurred to me that installing grub on sda might solve the problem, but I'd rather not since I like to have my windows hard disk unmodified so that booting to it from the BIOS boots directly to windows. A possible work around is to use the BIOS as a bootloader, by pressing F8 to select the boot device. Still, I'd like to know why the problem is happening in the first place.

  Read the article

• How small (spec wise) can a virtual machine be and still boot up and run some sort of OS?

  - by IllvilJa

  One of the advantages with virtual machines is that you can be very flexible with their sizes. If the host system permits it, you can have a very large virtual machine with a lot of virtual RAM and disk. Also, you can decide to go the other way around, to give the virtual machine a very modest amount of RAM and disk and then choose and configure the OS appropriately. The question is, how small virtual machines have people managed to setup (and get to both boot up and to run)? Virtual machines doing something usuful is preferable, even if I know "useful" in this context is awfully subjective, but laboratory-cases with a configuration stripped beyond common sense could be intresting as well, just to see what people manage to boot and run. Quite open ended question and quite academic, but think of it: an extremely small VM (which still does something useful) takes very little memory and disk and can be quite quickly saved to and restored from disk. If it's also gentle on CPU resources, one might consider having a huge number of such VMs up and running on a host. (Imagine a VM running just an old Commodore 64 or Commodore Amiga in it. Ok, way wrong CPU architecture for modern Virtualization software running on a x86-based PC but still an interesting thought. You could have quite a few such small VMs running on a modern PC.)

  Read the article

• Are relative-path symlinks reliable on Rackspace Cloud Sites?

  - by Jakobud

  Rackspace's Cloud Sites have a lot of stupid limitations. For example, no SSH (in or out), no shell, no RSYNC, etc... (even through cron). Recently I learned that you can't reliably use symlinks in Cloud Sites. Apparently this is because the absolute path of your sites could change at any moment, since it's a shared host environment split up between many disks/servers. I guess different account's sites get moved from disk to disk whenever Rackspace decides to. Supposedly to increase efficiency across the board. So after talking with a Rackspace tech, he said they cannot guarantee that symlinks would always work. Obviously this is because if you have a symlink that use's an absolute path like this: //mnt/disk-34566/home/user34566/files/sites/www.mysite.com/mydir If you files go moved to a different disk (or whatever they do), then the absolute path would be different and the link would now be broken. That makes sense. So next, I asked the Rackspace tech if relative path symlinks were reliable. So if I have the following link: files/sites/www.mysite.com/mylink --> ../www.myothersite.com/anotherdir You can see that the symlink simply points to a nearby directory's sub-directory. He said they cannot guarantee that even those would always work either. Since it uses a relative path to another nearby directory I'm not sure how it could ever break from something Rackspace would do. Do relative symlinks somehow rely on absolute paths underneath? Or is Rackspace using some weird custom filesystem where they will break from absolute path changes? It seems like a relative-path symlink would be fine and would only break if the user did something to mess up the directories involved. But when the tech's say that they "don't officially support symlinks of any kind" that makes me hesitant to use them for large commercial websites in Cloud Sites. Can anyone with Rackspace experience give input on this topic?

  Read the article

• Can't log in after restoring from Time Machine

  - by Jay Conrod

  My friend uses a Macbook Pro with Snow Leopard 10.6.2. She uses both FileVault and Time Machine to preserve her data. Recently, she suffered a hard disk failure. After restoring from Time Machine using the Snow Leopard install disk, she gets the following error when logging in: You are unable to log in to the FileVault user account at this time. Logging into the account failed because an error occurred. When examining the file system through Terminal, I noticed her home directory is not present: there is no /Users/username directory, or the FileVault .sparsebundle file that's supposed to be there. When using Time Machine.app on /Users, it appears as if her home directory as never there. Additionally, I did a search on the backup disk with the following command: sudo find /Volumes/backup -name '*.sparsebundle' No results. She told me that after working with some large data files, Time Machine would come on, and it would sound like it was transferring a lot of data to the hard disk. Time Machine must have been doing something, right? How can we recover her files? Are they still there?

  Read the article

• How to bypass resume from hibernate [closed]

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• How do you monitor SSD wear in Windows when the drives are presented as 'generic' devices?

  - by MikeyB

  Under Linux, we can monitor SSD wear fairly easily with smartmontools whether the drive is presented as a normal block device or a generic device (which happens when the drive has been hardware RAIDed by certain controllers such as the one on the IBM HS22). How can we do the equivalent under Windows? Does anyone actually use smartmontools? Or are there other packages out there? The problem is that SCSI Generic devices just don't show up in Windows. If the drives aren't RAIDed we can see them fine. How I'd do it in Linux: sles11-live:~ # lsscsi -g [1:0:0:0] disk SMART USB-IBM 8989 /dev/sda /dev/sg0 [2:0:0:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg1 [2:0:1:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg2 [2:1:8:0] disk LSILOGIC Logical Volume 3000 /dev/sdb /dev/sg3 sles11-live:~ # smartctl -l ssd /dev/sg1 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 26~ Percentage Used Endurance Indicator |_ ~ normalized value sles11-live:~ # smartctl -l ssd /dev/sg2 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 3~ Percentage Used Endurance Indicator |_ ~ normalized value

  Read the article

• VMware vSphere 4.1 and BackupExec 2010

  - by Josh

  I'm sure a common problem with most shops is backups, their size, and the window in which you have to back up the data. What we are working with: VMware vSphere 4.1 Cluster PS4000XV Equallogic Storage Array (1.6TB Volume dedicated for Backup to Disk) Physical Backup Server with a single LTO4 drive. BackupExec 2010 R3 with the following agents, Exchange, SQL, Active Directory, VMware. Dual Gigabit MPIO Connections between all devices (Storage Array, Backup Server, VM Hosts) What we would like to accomplish: I would like to implement an efficient Backup to Disk to Tape solution where all of our VMs are backed up to the Storage Array first, and then once completely backed up to the array are replicated to tape. In the event we needed to recover, we would be able to do so directly from tape. Where we are at currently. Of the several ways I have setup the jobs in Backup Exec 2010 R3 the backup jobs all queue up at the same time, as soon as a job is finished backing up to disk it then starts that same job to tape, but pulling from the original source instead of the designated B2D location. I understand that I could create a job that backs up the "Backup to Disk" folder to tape, but in the event of restoration, I would first need to stage the data in the B2D folder before I could restore the VM. I would really like to hear from individuals in similar situations. Any and all comments and critiques are appreciated.

  Read the article

• Gray Progress Bar in Macbook Boot caused by Partition Fault

  - by Konstantin Bodnya

  Here's my problem: When I try to load my macbook it shows the gray progress bar. It takes a while to fill the whole progress and after it macbook just shuts down. I tried to boot from recovery partition and run Disk Utility to repair it. Disk Utility showed my "Macintosh HD" in a gray color and failed to repair it. I thought all my data was lost, but then I tried the following: So I booted into ubunto from live usb and it successfully mounted my macintosh hd hfs+ partition. Parted shows me the following partitions on my disk: Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 20.5kB 210MB 210MB fat32 EFI System Partition boot 2 210MB 499GB 499GB hfs+ Macintosh HD 3 499GB 500GB 650MB hfs+ Recovery HD Seems legit except for FAT32 for EFI System Partition. Since all my data is okay and backed up what should I do to recover the system. I don't really want to reinstall all the system though I believe there's a command to make it allright in linux. Thank you everyone!

  Read the article

• Bootable GRUB partition

  - by MA1

  I have a customized live fedora 12 USB which is working fine. What i want to do is to make a partition of my hard disk bootable so that my customized fedora can be run from hard disk. To accomplish this i did the following steps: Created a primary partition(/dev/sda2) and format it as ext3 and set it as active. Copy all the files in the live usb to /dev/sda2. Following are the live usb contents(all directories): a. boot b. EFI c. LiveOS d. syslinux Then i installed the GRUB in boot/grub Created the grub.conf in boot/grub Following are the contents of each directory in the USB: syslinux/ boot.cat isolinux.bin splash.jpg vesamenu.c32 initrd0.img ldlinux.sys syslinux.cfg vmlinuz0 LiveOS/ livecd-iso-to-disk osmin.img squashfs.img EFI/ boot/ boot.conf grub.conf boot.efi bootia32.conf bootia32.efi splash.jpg splash.xpm.gz vesamenu.c32 initrd0.img isolinux.bin isolinux.cfg vmlinuz0 boot/grub/ core GRUB files grub.conf olpc.fth Following are contents of grub.conf default=0 splashimage=/EFI/boot/splash.xpm.gz timeout 2 hiddenmenu title funLinux kernel /EFI/boot/vmlinuz0 root=live:LABEL=myFun rootfstype=auto ro liveimg quiet ssb.blacklist=1 selinux=0 vga=normal nomodeset rhgb initrd /EFI/boot/initrd0.img Now when i try to boot from the hard disk it shows the grub menu and fedora starting to load but during loading it said No root device found Boot has failed, sleeping forever So, where is the problem? what i am doing wrong?

  Read the article

• How to get multipath working for Ubuntu Server 12.04

  - by mlampi

  I'm working on a project which aims to make use of Ubuntu servers running on enterprise class hardware. In our case that means IBM HS23E blade servers, QLogic 4GB fibre channel extension cards and quite old IBM DS4500 disk array with two controllers. At the moment we have fibre channel as only boot option and Ubuntu Server 12.04 installed just fine and is able to boot without multipath. I'm not a linux professional myself but in our team we have people who will understand the technical stuff. Don't let my post confuse :) The current situation is that we have only one fibre channel connection to a single disk array controller. Real life case would be of course quite different. At minimum we should have two fibre channel ports connected to two different switches and two different controllers. However, we have no idea how to set up multipath tool. Is the DM-MPIO the right software? At minimum we should be able to boot when multiple connections are available and achieve fault tolerance when any of them should be down. Since the disk array is not the latest hardware, I managed to find RDAC driver sources only for 2.6.x kernel. And we have 3.2.x. Another issue is to build a multipath.conf. The said driver sources are from IBM support and the QLogic drivers provided to Ubuntu installer are from Ubuntu site. It seems that RHEL and SLES would have near out of the box support but that is not an option for our project. Actual questions: - What is the recommended software tool for multipath for Ubuntu Server 12.04? - Is there available pre-made configurations or templates? Does it require disk array / controller specific settings or do a more generic config work? - Do you have expriences on similar setup and like to share the knowledge? I'll provide you with any additional information you might require. Thanks in advance.

  Read the article

• How do I restart a Windows XP upgrade?

  - by Jason

  Is there a registry tweek to tell Windows Setup to start over? It tries to continue where it left off after I reboot. I can get to the Recovery Console. I tried to go from SP2-SP3. It failed, and I couldn't get to Safe Mode. I put in the SP1 disk (I don't have an SP2 boot disk, just the upgrade package.) It ran a couple minutes then gave me the error "the signature for windows xp professional upgrade is invalid" error code 800b0100. I rebooted to Safe Mode. I get to Safe Mode then say "Window XP Setup can't run under Safe Mode" press ok to restart. I put the SP3 disk back in, trying to get the "repair" option I didn't ever see putting in the SP1 disk, and it tried to continue the SP1 install - on the 4th step, and then gave the same signature error above. I need to get it to start over, so I can get to the repair option, to go back to SP2 (or install SP1 then add SP2 to it). Is there a registry tweek to tell Windows Setup to start over?

  Read the article

• Ubuntu Wubi "drive" failure; mount drive in XP?

  - by 618034

  Hi there, I installed the Wubi distribution of Ubuntu on a separate partition (which is silly, since why do I care if Windows can still manage the partition?) a few months back; it was pretty awesome, until Linux hosed. At this point, I can get Ubuntu to boot if I try really hard through grub, but once it does start, the screen is hosed, so no dice. At this point, I'd like to wipe it all and start over, but I need to get some stuff off the "disk". The Wubi install makes this difficult, since the "disk" is a flat file on an NTFS partition. I've done just about everything I can think of — I renamed the virtual disk .iso, mounted it with VirtualCloneDrive, then used whatever magic EXT3 (EXT4?) readers I could dig up on the Internet to parse the mount — but nothing's working. Can you offer any suggestions? The "disk" is currently in D:\ubuntu\disks\root.iso. Many thanks! (I may be high-latency at the moment, apologies if I don't address follow-ups quickly)

  Read the article

• Successful login with iscsiadm on target still doesn't create block device

  - by Halfgaar

  I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

  Read the article

• Trouble cloning a Macbook Pro hard drive

  - by Mirko Froehlich

  I am trying to upgrade the 250GB hard drive in my MacBook Pro (early 2008 model) to a 750GB drive. I have connected the new drive via an external USB enclosure. The drive is recognized fine, I can format it, etc. However, every time I try to clone the drive, I am getting Input/Output errors. Before the clone operation, I have verified both the internal and the external drive using Disk Utility, and they both check out fine. After the clone operation, the external drive shows multiple "Invalid node structure" errors: I have tried two approaches for cloning the drive: Using Disk Utility, by starting from the OSX install DVD Using Carbon Copy Cloner The outcome is the same in both cases. The Carbon Copy Cloner logs show a handful of the following types of errors: rsync: mkstemp "<... an external filename ...>" failed: Input/output error (5) rsync: stat "<... an external filename ...>" failed: Input/output error (5) The actual files affected seem to be different across different runs of the application. Before the last run, I used Disk Utility to (once more) reformat the external drive and explicitly overwrite it with zeros, but this made no difference. I also tried running a surface scan in Tech Tool Pro overnight. It got about 2/3 of the way through before I had to disconnect the drive (had to take my MacBook Pro to work), but so far it didn't report any bad blocks. Assuming it scans the drive in the same order in which blocks would be allocated during actual use, it seems like if bad blocks were to blame for the clone failures, they should have been found already (given that the source drive is only 250GB). As a last attempt, I may try SuperDuper as well, although my understanding is that it uses the same underlying rsync approach as Carbon Copy Cloner, so it's unlikely to perform any better. Are there any other things I should try before I send the drive in for a replacement? Could these problems be caused by my internal drive, even though it works fine and checks out fine in Disk Utility?

  Read the article

• SSD seems dead after wakeup from Windows Sleep, BIOS stalls but doesn't find it anymore

  - by Abel

  The morning, the following scary scenario happened: I woke up my Windows system Typed in my username and got an error (something like "could not load security xxx", but unsure of exact wording) System auto-restarted after cliking OK It didn't boot up anymore to the SSD with Windows 7 OS (I have another disk I can boot to, but that doesn't see the disk either). Obviously, this happened right after I instantiated a backup procedure, which hasn't succeeded either. The BIOS can't find the drive when I connect to SATA. And it can't find the drive when I connect it to SAS. I have a Dell Workstation T7400, most recent BIOS (version A06), version of SAS Host Bus Adapter BIOS (HBA) is MPTBIOS 6.14.10.00 (2007.09.29) from LSI Logic Corp. Other findings: When connecting to SATA, the DELL Logo screen stays really long (5 minutes) and then at the end of POST it says that a drive is not found When connecting to SAS, the SAS HBA initializing phase takes long (2 minutes, against normally 15 seconds) When running Dell Diagnostics, it doesn't finish and gives the error Exception occurred in module MPCACHE.MDM file "IOAPICSP.ASM" line 1645. I contacted Dell. On their advice I tried different slots and different cables to no avail. I use an APIC battery power, spikes in the power are thus unlikely. My conclusion so far: the disk is dead. I need this disk very badly because it contains the last few days of important development of which not all code was checked in the moment this happened. Are there any ways to recover dead SSD drives? The drive is a new X25-M G2 160GB model SSDSA2M160G2GC 2.5" in an extension bay and has been running without issues for 3 months on SAS.

  Read the article

• Degraded RAID-5 array with lvm2 lost superblock and partition table

  - by Fred Phillips

  I have a RAID-5 array of 4x1TB hard disks with one lvm2 partition on Ubuntu Linux 10.04 LTS. One of the disks has failed. I have re-assembled the array without this failed disk but now mdadm --examine claims the array has no superblock and fdisk says it has no partition table. What can I do to recover the data? # mdadm -D /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sat Mar 5 14:43:49 2011 Raid Level : raid5 Array Size : 2930276352 (2794.53 GiB 3000.60 GB) Used Dev Size : 976758784 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Sat Mar 5 15:06:49 2011 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 1 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Name : boba:1 (local to host boba) UUID : 52eb4bc9:c3d8aab5:e0699505:e0e1aa05 Events : 18 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 65 1 active sync /dev/sde1 2 8 49 2 active sync /dev/sdd1 3 0 0 3 removed 4 8 17 - faulty spare /dev/sdb1 # mdadm --examine /dev/md0 mdadm: No md superblock detected on /dev/md0. # fdisk -l /dev/md0 Disk /dev/md0: 3000.6 GB, 3000602984448 bytes 2 heads, 4 sectors/track, 732569088 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1572864 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10] md0 : active raid5 sdb1[4](F) sda1[0] sdd1[2] sde1[1] 2930276352 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_] unused devices: <none>

  Read the article

• What to do with a broken OS X install disc?

  - by slhck

  First things first: I don't appreciate software piracy and I really want to spend money on software that I use and that I work and make money with. I don't want this question closed just because I consider downloading software, I only want honest opinions and alternatives. Here we go: So I have my OS X Snow Leopard Upgrade DVD, but it's horribly scratched and won't boot anymore. It endlessly loads and at some point I have to force pull it out of the disc slot. How can I reset my Mac then? Can I take my original disk to an Apple Store and ask them for a replacement? Will they believe me, even if I don't have the receipt anymore? Would owning the original disk make it okay for me to look somewhere on the internet and download it? I don't even know if that will work without hassles. Could I try to read the disk to an image with some error correction methods? Maybe during boot it can't read some files, but some other program can? Is there any other way of resetting the Mac? Mine's now over 3 years old an I seem to have misplaced my original discs that had 10.4 on it. Or should I just buy a new 10.6 upgrade disk? (Which is not really what I want to do) Answers and opinions would be much appreciated.

  Read the article

• Can I format a Veritas cluster shared volume from windows?

  - by spaghettidba

  We have a Microsoft Failover Cluster with dynamic disks managed by Veritas Storage Foundation. Today the sysadmins added a new disk for SQL Server but the cluster size on the volume was wrong, so I issued a quick format to change it. The disk volume failed, the SQL Server group failed as well and the cluster became unresponsive. After some minutes I managed to fail over to a passive node. The SAN admins say it's my fault because I shouldn't have formatted the disk from the Windows format applet, but I should have used Veritas Enterprise Administrator instead. Can a format operation bring offline a whole cluster group this way? Relevant error messages: From the eventlog: The cluster resource host subsystem (RHS) stopped unexpectedly. An attempt will be made to restart it. This is usually due to a problem in a resource DLL. Please determine which resource DLL is causing the issue and report the problem to the resource vendor. From the cluster.log ERR [RCM] rcm::RcmResControl::DoResourceControl: ERROR_RESOURCE_CALL_TIMED_OUT(5910)' because of 'Control(STORAGE_GET_DISK_INFO_EX) to resource 'NameOfTheDiskGroup' timed out.' Veritas Documentation: Excerpt from Symantec's documentation: Note: Before manually creating the resource, you must format the cluster-shared volume with NTFS using the VEA GUI and mount it on the node where you are trying to create the resource. Does this mean the disk cannot be formatted from Windows? I don't read it that way. For the record, I formatted many disks using the Windows applet in the past and nothing bad happened.

  Read the article

• iMac 20inch (Mid 2007) SL DVD Boot Prohibitory Sign

  - by Caitlann Lloyd

  iMac 20inch (Mid 2007 Build) with Ubuntu 12.0.4 How I got in this situation I had a perfectly healthy Intel iMac running Snow Leopard several months ago. Then I got the dreaded spinning gear and several kernel panics. After getting a little frustrated (failing to find a solution online), I found an old macbook installation disk and used it to access Disk Utility. From here, I erased my entire hard drive leaving me with no OS. I then created a Ubuntu DVD and installed Ubuntu onto the system. Now, on Ubuntu, I wine installed Transmac and burned a Single layer copy (with languages, etc. removed to save space) of Snow Leopard onto a 4.7GB DVD. I tried to boot from it and was met with first the grey apple screen and a spinning cog before the grey apple shortly turned into the infamous prohibitory sign. Note: I met this problem previously when using Disk Utility to create a bootable USB of Snow Leopard, hence I severely doubt it has anything to do with the DVD created. Resources at my disposal 1 x iMac running Ubuntu 6 x 4.7GB DVDs 1 x USB Stick 12GB 1 x Windows 7 Laptop Resources I do not have Firewire cables Access to a prebuilt retail disk (Misplaced) Access to another Mac Apple Warranty I would be hugely grateful if someone was able to tell me how to install Snow Leopard again.

  Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >