Search Results

Search found 9667 results on 387 pages for 'hardware monitoring'.

Page 99/387 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

  • Scanner Dayly Duty Cycle

    - by Juanp
    I'm comfused with the concept of 'Daily Duty Cycle'. For example if I have a scanner that the spec is: PPM (pages per minute): 90 and DDC (Daily Duty Cycle): 800. and I am interested in scanning ONLY 10hours continuously, what would it be the best choice: 90 * 60 * 10 = 54.000 or (800 / 24) * 10 = 333 It is very different results. what would it be the best option?

    Read the article

  • Can I create a virtual network interface to connect to a real network device?

    - by michelemarcon
    I have a networked windows pc with 2 network interfaces. The first connects to a lan with ip address 10.1.. The second connects to another lan with ip address 10.2.. Maybe it's a dumb question, however is it possible to virtualize the second network interface, so that the pc can connect to the 2 lans? If necessary, I may switch to linux or paravirtualization. CLARIFICATION: I want to send DHCP broadcast packets on the second lan, but not on the first lan. I want to do it with one single physical network interface. At the moment, I'm not using any virtualization software.

    Read the article

  • Computer only booting after POWER ON/OFF 10 times or more?

    - by Jan Gressmann
    Hi fellow geeks, recently my computer started to behave like an old car and won't start up anymore unless I flip the power switch repeatedly. What happens when I power it on: CPU fans spins briefly and very slowly, then it stops Same with GPU fan No BIOS beeps or HDD activity Screen stays black After turning it on and off for like 10 times, it'll eventually boot like normal and run smooth without any problems what-so-ever. But I'm worried it might eventually die completely. Anyone know the most common cause of this? Maybe I should just leave the computer powered on? :)

    Read the article

  • Is it normal for a SAS drive to have a few bad blocks, or should I replace my drive ASAP?

    - by Nate
    I have a drive—part of a RAID 1 mirror—that has two bad blocks. Adaptec Storage Manger e-mailed me when it detected the blocks. It shows 4 medium errors for that drive, but state is still “optimal”. This is my first time using Adaptec RAID controllers. I don’t know if an occasional bad block is normal, or if I should immediately replace that drive. Update: The drive failed later the same day! The disk subsystem is: Adaptec 6405 with ZMM (2) Seagate near-line SAS drives (ST31000424SS) The other drive hasn’t reported any bad blocks yet. I am running a consistency check.

    Read the article

  • Computer powering off after 10 mins or so

    - by Jack
    I have no OS installed, and I am trying to use a linux boot disc. However it is not a linux problem....if I just leave the computer on at the no operating system found message, it still turns off. I thought maybe it was overheating, but I am 90% sure that is not the problem. What else could cause this?

    Read the article

  • Is there way to enable 4 GB RAM in 32-bit Windows OS?

    - by Wahid Bitar
    I upgraded my PC to 4 GB RAM and I get only 3 GB. Windows 7 32-Bit consider that I've 4 GB RAM but didn't use more than 3 GB. Someone told me that MS Windows 32-bit doesn't support RAM larger than 3 GB. So please is there any way to make my OS "Windows 7 32-Bit" support more than 3 GB RAM ? *`Note: I can't move to 64-bit because I've many program doesn't work with a 64-bit OS. Edit:: I tried what Mr. Wonsungi advised me but whenever I check this option: Enable support for 4 GB of RAM I get the following error: 'Cannot access to the registry key HKEY_CLASSES_ROOT\CLSID\{E88DCCE0-11d1-A9F0-00AA0060FA31}.' There is no "CLSID" in my registry, I don't know why!.

    Read the article

  • How cpu writes data to dynamic RAM

    - by Krit
    Hello, I would like to know what kind of electrical signals does a cpu send to a dynamic RAM when it wants to write one bit (a 1 or 0). Is it simply that cpu sends just a single electric pulse, and if that electric pulse's voltage is higher than a certain level, it charges the capacitor to a voltage level that is "1" and if it is at a lower voltage band, it charges capacitor to level that it is "0"?

    Read the article

  • Shuttle FB51 mobo does not boot with external USB drive attached [closed]

    - by user127236
    I am repurposing an old Alienware desktop as a home media server. The PC is based on the Shuttle FB51 motherboard. The BIOS is a Phoenix Version 6.00 PG, release date 12/16/2002. I have loaded Ubuntu 12.04 LTS on the internal hard drive. I am using a Western Digital WD Elements 1.5 TB USB 2.0 Desktop External Hard Drive for media storage. When the external drive is plugged in and the PC is powered on, it freezes very early in the BIOS self-test, even before it begins the memory test. If I unplug the drive, the self-test proceeds without further problems. I can plug the USB drive back in when the self-test is complete, and Ubuntu will boot and find the external drive normally. I've tried several changes to the BIOS setup without finding a cure for the boot issue. Any assistance gratefully accepted. JGB

    Read the article

  • How long until the chirping stops or what can I do to make it stop?

    - by MadBurn
    I know computers, I have been fixing them and building them for over a decade... but I don't know the exact electronics of them. My personal desktop PC is making an irregular, but constant, extremely high pitched chirping noise. I know this could be my hard drive, but I've heard that noise before and I believe this is a capacitor or part of the electronics. This noise is right at the edge of my hearing and I can feel it more than I can hear it. After a while, it starts to give me a headache and makes me physically sick. How long will this last? Is there anything I can do to fix it (short of replacing the entire motherboard)?

    Read the article

  • Windows Server 2008 R2 Maximum Processor Limit Confusion

    - by Stevoni
    As I was looking through the Windows Server 2008 R2 specifications, I saw that the maximum supported processors is 64 sockets for Datacenter addition. This puts the maximum number or cores at 256 (if all sockets are quad cores), which I think it's just silly, but whatever. And now the questions: How does one set something like that up? (Obviously not for me, but humor me) Are there multiple dual socket motherboards running in a giant case with a ton of memory? How does the OS see all of the CPUs if they're on different boards? What would be a real world example of a need to have 64 sockets attached to one operating system vs 32 2 socket servers?

    Read the article

  • my computer makes vibrating sounds

    - by Nrew
    I don't know why but every morning when I turn on the computer, it makes a vibrating sound. Like its case is attached to a vibrator. But when I turn it off and turn on again using the power button(still at os choices) the sound is gone. Why is my computer creating the sound?

    Read the article

  • New harddrives failing within weeks.

    - by Jason Kealey
    I've experienced 8 hard disk failures in 3 months and have tried many things to solve the issue permanently but I have failed. I would like to know if you have any advice for me. System was running Win XP on an Asus P5W-DH Deluxe. I have setup a RAID-1 array. I started out with 2 x 500 GB 7200RPM Western Digital drives. One died. I took it out to RMA it. On the same day, the router was fried. Assumed a power surge occurred; connected an older UPS to protect the system. Once I got my hands on an identical disk, I installed it. The RAID array was rebuilt. A few days later, the other one died. Assumed the rebuild caused it to fail. Took it out for RMA. Before the other one arrived, the remaining one died. I then discovered I could re-enable them using the Intel Matrix Storage Manager. I re-enabled both and the system seemed fine for a week, until both died again. I got two new 1.5 TB 7200RPM Seagate drives and re-installed Windows 7. Also replaced the UPS and power supply. They both died again. The voltage on the plug is stable between 120 and 122V as per the UPS. None of the other devices have had any problems (monitors, etc.). At this point, I see two options: a) electrical issue in the house that was, for some reason, not blocked by the UPS. b) something else inside the system causing surges? motherboard? onboard raid controller? Failures happen fairly quickly, between 2 and 14 days after I fix the previous issue. I just gotten a new computer (Core i7) to replace it. If it is stable, I can determine that b) was the problem. If it fries its hard drive again, I can determine that it is an electrical issue in the house. Do you have any other thoughts? Any tools I can run on the drives that failed to get more information about the original SMART event history?

    Read the article

  • Configuring a monitor's contrast/brightess/colours/etc

    - by DMA57361
    I have recently bought myself a new monitor, now I'd had my previous screen well over 5 years now so I'm looking at this one thinking the picture doesn't quite look right (not bad, just different). Rather than just wait until I'm used to the new picture I'd rather get it fine tuned, then get used to it - so I can reap the maximum benefit. So, can you please suggest reliable ways of configuring an LCD monitor's brightness/contrast/colour/etc to provide the optimum possibly quality image?

    Read the article

  • How can I get multiple video cards to work on linux?

    - by user17943
    I installed fedora 12. I have 2 ATI cards that I used to use on windows to run 4 monitors. A recurring problem has been to get them detected in linux. Only my secondary card is picked up linux. When I manage the displays it detects the 2 monitors connected that card. What are the specific steps I should take to get the second card detected? Supposedly there is a tool system-config-xfree. I don't have it, yum can't find it. Also I heard it has something to do with editing some xorg.conf file or something to that effect. I have absolutely no idea how to find the "bus id" of my card, or lookup the horizontal refresh rates, etc.. I would probably have no problem following the documentation & editing the file if I knew a good way to find these values. Someone also suggested installing linux twice and saving the xorg.conf it generates each time (with different card each time) and then merging the two by hand. That is like killing a fly with a hammer though, when I do this again and again in the future It'd be nice to not have to take twice as long. Thanks

    Read the article

  • PC has a mind of it's own.

    - by ULTRA_POROV
    When I put my PC into standby, sometimes it randomly awakes, scaring me and waking me up. What could be causing this. No it is not my mouse moving, it can only be powered back on by the power button. It's really strange.

    Read the article

  • Proper approach to debug PC startup problems (POST)

    - by saurabhj
    My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

    Read the article

  • Shopping for a very compact and powerful workstation [closed]

    - by qdot
    I'm on the market for something small, size of an Mac Mini, could be heavier, that packs a lot of compute power - goal is to have a fast, known development machine at customer's site, but still easier to fly with than desktop-replacement laptops. If Mac Mini came with a quad-core i7, it would be my likely choice. Any other manufacturers to look at? Or perhaps a Mini can be upgraded beyond official specs?

    Read the article

  • Hp pavilion dv7 power button

    - by Danny B
    My power button is non responsive I am getting LED for charging. I've taken it apart before to change the dc jack and it was fine and a few months later it just powered off. I try to power back on and is goes to start up then shuts off. I just took it apart and came to find the ribbon cable connecting the power button/speakers cover is barely hanging on do I have to replace the whole thing or is there a way to replace the ribbon cable?

    Read the article

  • HDD not detected whenever first power on (detected at BIOS level)

    - by Alvin Lim
    I am using Asus P8H61-M LX Motherboard with latest version of BIOS: 4401 One SATA-3 Western Digital Black Series 1.5TB is attached to SATA port 0 A Samsung 22x DVDRW SATA drive attached to SATA Port 1. ps/2 Logitech mouse and keyboard. CPU is i3 with DDR3 8Gb RAM. no other devices are installed. My problem is that when I turn on the computer, the WD HDD is not detected. ie cannot be booted. I have to press ctrl+alt+del in order to get it detected. I'd used the WD data lifeguard software to scan the HDD, the smart status is OK, the surface scan does not show any error at all. Where did I do wrong? Any advice is greatly appreciated.

    Read the article

  • Server drives: 2.5" SCSI less reliable than 3.5" ?

    - by Bill
    Just had an HP 2.5" SAS 10k drive fail on a RAID5 array after about 2.5 years. It made me wonder if this was a fluke or an indication that 2.5" drives are less reliable than 3.5" SAS drives. I've had many 3.5" SAS drives running for many years without any issues (knock on wood). I would think that smaller drives would generate less heat and therefore be more reliable, but couldn't find any evidence of this. I realize all drives will eventually fail and that it's a crap shoot with any particular model, but was hoping someone could point out some related studies or comment on the SCSI drive sizes they've found to be most reliable in servers. Thanks.

    Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >