Search Results

Search found 28 results on 2 pages for 'qlogic'.

Page 1/2 | 1 2  | Next Page >

• Solaris Fibre Channel target - Configure QLogic QLA2340

  - by growse

  I'm currently trying to set up a small storage system as a fibre channel target. This is for testing, so I'm currently using Solaris (Nexenta) and a QLogic QLA2340 HBA. For some reason, the qlc and qlt drivers don't support the QLA2340, so I'm using the qla2300 driver from QLogic's website. I've also got the scli utility installed for configuration. The HBA is detected by the system. That said, it's not clear how I get from this point to a point where I have a ZFS volume being exposed as an FC target. I was originally following this guide (http://www.youtube.com/watch?v=yzEBd3l7Qn4) but it seems that without the qlc/qlt drivers, Sun's configuration tools won't work. Does that also imply that COMSTAR also won't work? What's the best way to expose an FC target with this setup? Most of the options I'm seeing in scli complain that the port state is LinkDown (it is, I've not plugged anything in yet). Do I have to have my FC client plugged up and working before I can configure the target? Apologies for the slight vagueness of the question, but I'm not overly familiar with the terminology.

  Read the article

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• HP Upgrades SAN Storage, OEMs QLogic Fibre Channel Switches

  HP unveils new offerings for iSCSI and Fibre Channel storage networking environments.

  Read the article

• MultiPath configuration on RHEL5 and Clariion CX-300

  - by Kamil Z

  I have problem with discovering my FC-connected CX-300 storage. Frankly speaking I'm complete novice in FibreChannel, so step by step explanation would be appreciated. My configuration consist of two IBM HS20 blades with RHEL5.4 on board and 2x Qlogic ISP2422-based 4Gb Fibre Channel HBAs on each blade. As a FC switch there are two Brocades built in BladeCenter Chassis, and finally there is EMC Clariion CX-300. CX300, and Brocade switches should be configured properly, because they were working fine with previous configuration, which main defference was RHEL3 instead RHEL5.4 Below there is my output from several usefull commands: #lspci | grep Fibre 06:01.0 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) 06:01.1 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) #lsmod | grep qla qla2xxx 1084741 0 scsi_transport_fc 37577 1 qla2xxx scsi_mod 141717 10 scsi_dh,qla2xxx,sg,scsi_transport_fc,usb_storage,libata,mptspi,mptscsih,scsi_transport_spi,sd_mod #cat /proc/scsi/scsi Attached Devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: LSILOGIC Model: 1030 IM IM Rev: 1000 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 I'd followed instructions from this site (editing /etc/multipath.conf), but i failed after multipath -ll - the output was empty. Do you have any suggestions about discovering FC Connected LUNs in such configuration?

  Read the article

• Oracle Linux Partner Pavilion Spotlight - Part IV

  - by Ted Davis

  Welcome to the final Oracle Linux Partner Pavilion Spotlight Part IV.  Two days left till the Big Show. You are gearing up. We are gearing up. You can feel the excitement.  We can feel the excitement. This. Will. Be. The. Best. Show. EVER. See you at the Partner Pavilion (Moscone south # 1033) at Oracle OpenWorld. - Oracle Linux / Oracle VM Team HP and Oracle are pleased to announce another Oracle Validated Configuration based on the ProLiant DL980 server. Many choose to deploy Oracle workloads on the ProLiant DL980 based on the cost/performance ratio they achieve running Oracle Linux Unbreakable Enterprise Kernel. You can be confident that Oracle Validated Configurations based on ProLiant servers will help you achieve your most demanding performance goals. QLogic The QLogic-Oracle partnership spans over 20 years resulting in the most comprehensive line of Oracle Linux I/O adapter technology. Interface options include Ethernet, Fibre-Channel, and FCoE. Host side connectivity is offered in both low profile PCIe and Express Module PCIe form factors. QLogic software drives are jointly qualified and “in-box” with Oracle Linux 5.x, 6,x and Oracle VM enabling simplified installation and management while simultaneously taking risk out of the solution. Bringing innovations such as NPIV, T10-PI, and intelligent caching adapter technology to the Oracle Linux environment further strengthens the QLogic advantage. A big thank you to all of our Oracle Linux Partner Pavilion participants. We - they- look forward to meeting you next week at Oracle OpenWorld. If you've missed our three previous Partner Spotlight's - here are the links: Part I, Part II, Part III. 

  Read the article

• 8Gb Fiber Channcel HBA vs. 10 Gb SPF+ Converged HBA

  - by Hossein Aarabi

  I am putting a Dell server together, more specifically R720. I have to select the correct Host Bus Adapter. This HBA on R710 will connect to a storage device. I am confused between these two: QLogic 2562, Dual Port 8Gb Optical Fiber Channel HBA (price $2,045) QLogic 8262, Dual Port 10Gb SFP+, Converged Network Adapter (price $1,618) I thought since the QLogic 2562 is a fiber channel and is more expensive then it is faster in terms of IOPS. But, it is a 8Gb as opposed to 10 Gb of SFP+. My questions: Which one is better (IOPS performance, etc.)? Why should I choose one over another?

  Read the article

• EMC, NetApp Strike Storage Networking Deals

  QLogic and EMC partner on Fibre Channel switches as Emulex notches an FCoE win with NetApp.

  Read the article

• Oracle TimesTen In-Memory Database Performance on SPARC T4-2

  - by Brian

  The Oracle TimesTen In-Memory Database is optimized to run on Oracle's SPARC T4 processor platforms running Oracle Solaris 11 providing unsurpassed scalability, performance, upgradability, protection of investment and return on investment. The following demonstrate the value of combining Oracle TimesTen In-Memory Database with SPARC T4 servers and Oracle Solaris 11: On a Mobile Call Processing test, the 2-socket SPARC T4-2 server outperforms: Oracle's SPARC Enterprise M4000 server (4 x 2.66 GHz SPARC64 VII+) by 34%. Oracle's SPARC T3-4 (4 x 1.65 GHz SPARC T3) by 2.7x, or 5.4x per processor. Utilizing the TimesTen Performance Throughput Benchmark (TPTBM), the SPARC T4-2 server protects investments with: 2.1x the overall performance of a 4-socket SPARC Enterprise M4000 server in read-only mode and 1.5x the performance in update-only testing. This is 4.2x more performance per processor than the SPARC64 VII+ 2.66 GHz based system. 10x more performance per processor than the SPARC T2+ 1.4 GHz server. 1.6x better performance per processor than the SPARC T3 1.65 GHz based server. In replication testing, the two socket SPARC T4-2 server is over 3x faster than the performance of a four socket SPARC Enterprise T5440 server in both asynchronous replication environment and the highly available 2-Safe replication. This testing emphasizes parallel replication between systems. Performance Landscape Mobile Call Processing Test Performance System Processor Sockets/Cores/Threads Tps SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 218,400 M4000 SPARC64 VII+, 2.66 GHz 4 16 32 162,900 SPARC T3-4 SPARC T3, 1.65 GHz 4 64 512 80,400 TimesTen Performance Throughput Benchmark (TPTBM) Read-Only System Processor Sockets/Cores/Threads Tps SPARC T3-4 SPARC T3, 1.65 GHz 4 64 512 7.9M SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 6.5M M4000 SPARC64 VII+, 2.66 GHz 4 16 32 3.1M T5440 SPARC T2+, 1.4 GHz 4 32 256 3.1M TimesTen Performance Throughput Benchmark (TPTBM) Update-Only System Processor Sockets/Cores/Threads Tps SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 547,800 M4000 SPARC64 VII+, 2.66 GHz 4 16 32 363,800 SPARC T3-4 SPARC T3, 1.65 GHz 4 64 512 240,500 TimesTen Replication Tests System Processor Sockets/Cores/Threads Asynchronous 2-Safe SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 38,024 13,701 SPARC T5440 SPARC T2+, 1.4 GHz 4 32 256 11,621 4,615 Configuration Summary Hardware Configurations: SPARC T4-2 server 2 x SPARC T4 processors, 2.85 GHz 256 GB memory 1 x 8 Gbs FC Qlogic HBA 1 x 6 Gbs SAS HBA 4 x 300 GB internal disks Sun Storage F5100 Flash Array (40 x 24 GB flash modules) 1 x Sun Fire X4275 server configured as COMSTAR head SPARC T3-4 server 4 x SPARC T3 processors, 1.6 GHz 512 GB memory 1 x 8 Gbs FC Qlogic HBA 8 x 146 GB internal disks 1 x Sun Fire X4275 server configured as COMSTAR head SPARC Enterprise M4000 server 4 x SPARC64 VII+ processors, 2.66 GHz 128 GB memory 1 x 8 Gbs FC Qlogic HBA 1 x 6 Gbs SAS HBA 2 x 146 GB internal disks Sun Storage F5100 Flash Array (40 x 24 GB flash modules) 1 x Sun Fire X4275 server configured as COMSTAR head Software Configuration: Oracle Solaris 11 11/11 Oracle TimesTen 11.2.2.4 Benchmark Descriptions TimesTen Performance Throughput BenchMark (TPTBM) is shipped with TimesTen and measures the total throughput of the system. The workload can test read-only, update-only, delete and insert operations as required. Mobile Call Processing is a customer-based workload for processing calls made by mobile phone subscribers. The workload has a mixture of read-only, update, and insert-only transactions. The peak throughput performance is measured from multiple concurrent processes executing the transactions until a peak performance is reached via saturation of the available resources. Parallel Replication tests using both asynchronous and 2-Safe replication methods. For asynchronous replication, transactions are processed in batches to maximize the throughput capabilities of the replication server and network. In 2-Safe replication, also known as no data-loss or high availability, transactions are replicated between servers immediately emphasizing low latency. For both environments, performance is measured in the number of parallel replication servers and the maximum transactions-per-second for all concurrent processes. See Also SPARC T4-2 Server oracle.com OTN Oracle TimesTen In-Memory Database oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 Enterprise Edition oracle.com OTN Disclosure Statement Copyright 2012, Oracle and/or its affiliates. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Results as of 1 October 2012.

  Read the article

• Link rate between EMC DAE and HBA

  - by Johan Christensson

  I have a EMC DAE (KTN-STL4) drive cage directly connecconnected to a HP Proliant server using a QLogic QLE2560 HBA. I'm using copper cable between the HBA card and the DAE. On the controller card in the DAE there is a label that states "4Gb". I'm guessing that this means 4Gbit/s. But if I set the HBA card to "Auto speed" it negotiate 2Gbit/s, and if I hard set it to 4Gbit/s I end up with no link. Why is this? Isn't the DAE controller card capebel of link speed higher then 2Gbit/s or is it the copper cable that limits the speed, or is it the interface used between the DAE and Qlogic HBA that is the problem? I have been browsing for HSSDC-FC converters and they always seems to på rated at ~2Gbit/s. If this is the limit, why does it say 4Gb on the controller cards in the DAE?

  Read the article

• VISIT ORACLE LINUX PAVILION @ORACLE OPENWORLD

  - by Zeynep Koch

  Back by popular demand, Oracle will again host the Oracle Linux Pavilionat Oracle OpenWorld from October 1-3. The pavilion will be located in the Exhibition Hall at Moscone South, Booth 1033, next to the Oracle DEMOgrounds and Oracle Linux demopods. At the pavilion a select group of ISVs, IHVs, and SIs will showcase their products that have been Oracle Linux- and/or Oracle VM-certified. These certified products enable customer applications to run faster, thereby saving money.Partners exhibiting their solutions in the Oracle Linux Pavilion include: BeyondTrust: context-aware security intelligence for dynamic IT infrastructures such as cloud, mobile, and virtual technologies Centrify: control, secure, and audit access to cross-platform systems, mobile devices, and applications Data Intensity: cloud services and application management Fujitsu: technology platforms, private cloud, services, ubiquitous and device solutions HP: converged cloud, converged infrastructure, application transformation, and information optimization LSI: intelligent solid-state storage solutions for breakthrough database acceleration Mellanox: InfiniBand and Ethernet end-to-end server and storage interconnect solutions and services for data centers Micro Focus: mainframe solutions, application modernization and development tools, software quality tools NetApp: storage and data management QLogic: high performance networking Teleran: BI and data warehouse management solutions for Oracle Exadata Database Machine and Oracle Database Be sure to pick up your free Oracle Linux and Oracle VM DVD Kit if you visit one of these partners. And speaking of free, be sure to stop by for some cool treats, courtesy of sponsor QLogic: Smoothie Bar on Monday, October 1 from 2:30 p.m. - 5:30p.m. Ice Cream Social on Wednesday, October 3 from 1:00 p.m. - 2:00 p.m. We look forward to seeing you at the pavilion.

  Read the article

• Kernel Error during upgrade or update commands

  - by Ashesh

  I am getting these errors during sudo apt-get update and upgrade... I tried all possible options no success. I recently upgraded to 13.04 and had problems with Broadcom WiFi. Fixed tat issues using the clean script... but looks like it did not install the Kernel properly.. Here is the o/p of the few scripts I ran: ashesh@ashesh-HPdv4:~$ sudo dpkg -r bcmwl-kernel-source (Reading database ... 175338 files and directories currently installed.) Removing bcmwl-kernel-source ... Removing all DKMS Modules Done. update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-25-generic cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/mtd/mtd.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/mtd/mtd.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/sfc/sfc.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/sfc/sfc.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/mellanox/mlx4/mlx4_core.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/mellanox/mlx4/mlx4_core.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/broadcom/bnx2x/bnx2x.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/broadcom/bnx2x/bnx2x.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/broadcom/cnic.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/broadcom/cnic.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/qlogic/netxen/netxen_nic.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/qlogic/netxen/netxen_nic.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/brocade/bna/bna.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/net/ethernet/brocade/bna/bna.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/scsi/libfc/libfc.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/scsi/libfc/libfc.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/scsi/advansys.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/scsi/advansys.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/scsi/be2iscsi/be2iscsi.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/scsi/be2iscsi/be2iscsi.ko’: Input/output error cp: reading ‘/lib/modules/3.8.0-25-generic/kernel/drivers/scsi/bnx2i/bnx2i.ko’: Input/output error cp: failed to extend ‘/tmp/mkinitramfs_8gjKwQ//lib/modules/3.8.0-25-generic/kernel/drivers/scsi/bnx2i/bnx2i.ko’: Input/output error Bus error (core dumped) depmod: ../libkmod/libkmod-elf.c:207: elf_get_mem: Assertion `offset < elf->size' failed. Aborted (core dumped) I am not a techie but I need your support to resolve this without re-installation from scratch....

  Read the article

• Debian and Multipath IO problem

  - by tearman

  Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

  Read the article

• How to get multipath working for Ubuntu Server 12.04

  - by mlampi

  I'm working on a project which aims to make use of Ubuntu servers running on enterprise class hardware. In our case that means IBM HS23E blade servers, QLogic 4GB fibre channel extension cards and quite old IBM DS4500 disk array with two controllers. At the moment we have fibre channel as only boot option and Ubuntu Server 12.04 installed just fine and is able to boot without multipath. I'm not a linux professional myself but in our team we have people who will understand the technical stuff. Don't let my post confuse :) The current situation is that we have only one fibre channel connection to a single disk array controller. Real life case would be of course quite different. At minimum we should have two fibre channel ports connected to two different switches and two different controllers. However, we have no idea how to set up multipath tool. Is the DM-MPIO the right software? At minimum we should be able to boot when multiple connections are available and achieve fault tolerance when any of them should be down. Since the disk array is not the latest hardware, I managed to find RDAC driver sources only for 2.6.x kernel. And we have 3.2.x. Another issue is to build a multipath.conf. The said driver sources are from IBM support and the QLogic drivers provided to Ubuntu installer are from Ubuntu site. It seems that RHEL and SLES would have near out of the box support but that is not an option for our project. Actual questions: - What is the recommended software tool for multipath for Ubuntu Server 12.04? - Is there available pre-made configurations or templates? Does it require disk array / controller specific settings or do a more generic config work? - Do you have expriences on similar setup and like to share the knowledge? I'll provide you with any additional information you might require. Thanks in advance.

  Read the article

• Slow browsing through IE on Windows Server 2012

  - by Volodymyr

  We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

  Read the article

• ORACLE OPENWORLD - DAY 3 LINUX SESSIONS and ICE CREAM SOCIAL

  - by Zeynep Koch

  It had been two days of amazing sessions but we have more to come.  Day 3 will bring following sessions for Oracle Linux fans: Wed, October 3rd: Hands On Lab: Oracle Linux Package Management, 10:15am, Marriot Salon, 14/15 YB level Hands On Lab: Oracle Linux Storage Management, 12:45pm, Marriot Salon, 14/15 YB level Why Switch to Oracle Linux, 3:30pm, Moscone South #270 We also have a great Ice Cream Social to cool you down in this weather. Visit our Oracle Linux Pavilion, Moscone South #1033 between 1-2pm to see Partners that support Oracle Linux and Oracle VM and grab your ticket for an ice cream sponsored by QLogic. We look forward to seeing you in these great events.

  Read the article

• Oracle Expands Sun Blade Portfolio for Cloud and Highly Virtualized Environments

  - by Ferhat Hatay

  Oracle announced the expansion of Sun Blade Portfolio for cloud and highly virtualized environments that deliver powerful performance and simplified management as tightly integrated systems.  Along with the SPARC T3-1B blade server, Oracle VM blade cluster reference configuration and Oracle's optimized solution for Oracle WebLogic Suite, Oracle introduced the dual-node Sun Blade X6275 M2 server module with some impressive benchmark results.   Benchmarks on the Sun Blade X6275 M2 server module demonstrate the outstanding performance characteristics critical for running varied commercial applications used in cloud and highly virtualized environments.  These include best-in-class SPEC CPU2006 results with the Intel Xeon processor 5600 series, six Fluent world records and 1.8 times the price-performance of the IBM Power 755 running NAMD, a prominent bio-informatics workload.   Benchmarks for Sun Blade X6275 M2 server module  SPEC CPU2006  The Sun Blade X6275 M2 server module demonstrated best in class SPECint_rate2006 results for all published results using the Intel Xeon processor 5600 series, with a result of 679.  This result is 97% better than the HP BL460c G7 blade, 80% better than the IBM HS22V blade, and 79% better than the Dell M710 blade.  This result demonstrates the density advantage of the new Oracle's server module for space-constrained data centers.     Sun Blade X6275M2 (2 Nodes, Intel Xeon X5670 2.93GHz) - 679 SPECint_rate2006; HP ProLiant BL460c G7 (2.93 GHz, Intel Xeon X5670) - 347 SPECint_rate2006; IBM BladeCenter HS22V (Intel Xeon X5680)  - 377 SPECint_rate2006; Dell PowerEdge M710 (Intel Xeon X5680, 3.33 GHz) - 380 SPECint_rate2006.  SPEC, SPECint, SPECfp reg tm of Standard Performance Evaluation Corporation. Results from www.spec.org as of 11/24/2010 and this report.    For more specifics about these results, please go to see http://blogs.sun.com/BestPerf   Fluent The Sun Fire X6275 M2 server module produced world-record results on each of the six standard cases in the current "FLUENT 12" benchmark test suite at 8-, 12-, 24-, 32-, 64- and 96-core configurations. These results beat the most recent QLogic score with IBM DX 360 M series platforms and QLogic "Truescale" interconnects.  Results on sedan_4m test case on the Sun Blade X6275 M2 server module are 23% better than the HP C7000 system, and 20% better than the IBM DX 360 M2; Dell has not posted a result for this test case.  Results can be found at the FLUENT website.   ANSYS's FLUENT software solves fluid flow problems, and is based on a numerical technique called computational fluid dynamics (CFD), which is used in the automotive, aerospace, and consumer products industries. The FLUENT 12 benchmark test suite consists of seven models that are well suited for multi-node clustered environments and representative of modern engineering CFD clusters. Vendors benchmark their systems with the principal objective of providing comparative performance information for FLUENT software that, among other things, depends on compilers, optimization, interconnect, and the performance characteristics of the hardware.   FLUENT application performance is representative of other commercial applications that require memory and CPU resources to be available in a scalable cluster-ready format.  FLUENT benchmark has six conventional test cases (eddy_417k, turbo_500k, aircraft_2m, sedan_4m, truck_14m, truck_poly_14m) at various core counts.   All information on the FLUENT website (http://www.fluent.com) is Copyrighted1995-2010 by ANSYS Inc. Results as of November 24, 2010. For more specifics about these results, please go to see http://blogs.sun.com/BestPerf   NAMD Results on the Sun Blade X6275 M2 server module running NAMD (a parallel molecular dynamics code designed for high-performance simulation of large biomolecular systems) show up to a 1.8X better price/performance than IBM's Power 7-based system.  For space-constrained environments, the ultra-dense Sun Blade X6275 M2 server module provides a 1.7X better price/performance per rack unit than IBM's system.     IBM Power 755 4-way Cluster (16U). Total price for cluster: $324,212. See IBM United States Hardware Announcement 110-008, dated February 9, 2010, pp. 4, 21 and 39-46.  Sun Blade X6275 M2 8-Blade Cluster (10U). Total price for cluster:  $193,939. Price/performance and performance/RU comparisons based on f1ATPase molecule test results. Sun Blade X6275 M2 cluster: $3,568/step/sec, 5.435 step/sec/RU. IBM Power 755 cluster: $6,355/step/sec, 3.189 step/sec/U. See http://www-03.ibm.com/systems/power/hardware/reports/system_perf.html. See http://www.ks.uiuc.edu/Research/namd/performance.html for more information, results as of 11/24/10.   For more specifics about these results, please go to see http://blogs.sun.com/BestPerf   Reverse Time Migration The Reverse Time Migration is heavily used in geophysical imaging and modeling for Oil & Gas Exploration.  The Sun Blade X6275 M2 server module showed up to a 40% performance improvement over the previous generation server module with super-linear scalability to 16 nodes for the 9-Point Stencil used in this Reverse Time Migration computational kernel.  The balanced combination of Oracle's Sun Storage 7410 system with the Sun Blade X6275 M2 server module cluster showed linear scalability for the total application throughput, including the I/O and MPI communication, to produce a final 3-D seismic depth imaged cube for interpretation. The final image write time from the Sun Blade X6275 M2 server module nodes to Oracle's Sun Storage 7410 system achieved 10GbE line speed of 1.25 GBytes/second or better performance. Between subsequent runs, the effects of I/O buffer caching on the Sun Blade X6275 M2 server module nodes and write optimized caching on the Sun Storage 7410 system gave up to 1.8 GBytes/second effective write performance. The performance results and characterization of this Reverse Time Migration benchmark could serve as a useful measure for many other I/O intensive commercial applications. 3D VTI Reverse Time Migration Seismic Depth Imaging, see http://blogs.sun.com/BestPerf/entry/3d_vti_reverse_time_migration for more information, results as of 11/14/2010.                            

  Read the article

• Fiber Channel Loop vs Point to Point

  - by RandomInsano

  So, I'm playing with a couple of QLogic QLA2340s connected directly together. I've got options here to either have them act as a loop, or in point to point mode. What's the difference if I'm only going to have two machines connected together? Is point-to-point more efficient? The firmware has an option to prefer loop, then fall back to p2p. Anyone have any idea if there are performance benefits or drawbacks? It's pretty hard to find that information.

  Read the article

• Getting Partial / No Redundancy on VM's created on latest datastore

  - by Germano

  Hi, First some background. I'm in the process of upgrading my ESX servers from 3.5 to vSphere 4 and so far I have setup the new vCenter Server. Before I start the upgrade of the ESX, I needed more storage so I created 3 datastores from available space on my Equallogic PS6000 which has been connected for a while so as far as connectivity, nothing has changed. but now here's my problem, I get a "Partial / No Redundancy" on any VM that I create in any of these new datastores. I can create VM's on any of the older datstores on LUN's from exactly the same Equallogic and it works fine, but not the new ones. Keep in mind that these new datastores are the only ones that were created under the new vCenter, so I believe it must have something to do with it. Is anyone aware of any issues about creating datastored using the new vCenter but on a 3.5 ESX host? ISCSI with QLogic QLE406x Thanks in advance for nay help. Germano

  Read the article

• Why does eth0 show an IP if I'm booting into runlevel 1?

  - by banjer

  I'm having some issues with networking on a new Linux server I'm building. The OS is SLES 11. When booting into runlevel 1, I see that eth0 is showing an IP. Physically, there is a network cable plugged into the card associated with eth1, and then there is a network cable plugged into a QLogic iSCSI card (eth4, not shown). I've been troubleshooting this for awhile, and it seems like eth0 is somehow getting assigned an IP, even though it isn't configured in Linux or even plugged into the network for that matter. Thoughts? ifconfig -a Here is the ifconfig output (Sorry, I need more rep before I can post images on SF...)

  Read the article

• It's an Oracle Linux Wrap: Oracle Openworld 2012

  - by Zeynep Koch

  Are you still recovering from an amazing Oracle OpenWorld experience? 50,000 attendees had access to thousands of sessions, demos, hands-on-labs, networking opportunities, music concerts, and loads of fun. For the Oracle Linux team, this was a week full of many insightful sessions and customer interactions. In case you were unable to attend Oracle OpenWorld or missed some of content presented, here's a compilation of key session presentations, keynotes, and videos.Go to the Oracle OpenWorld content catalog and access all the session presentations. Oracle Openworld Keynote by Edward Screven Oracle's commitment to Open Source by Edward Screven Oracle Linux Interview with Wim Coekaerts Making the most of mainline kernel by Wim Coekaerts Why DTrace and Ksplice have made Oracle Linux 6 popular by W.Coekaerts How partnership between Oracle Linux and Oracle Partners benefits Sysadmins by Michele Resta Hugepages=Huge Performance on Oracle Linux by Greg Marsden Benefits of Kpslice in your Linux Environment by Tim Hill Oracle Linux, Ksplice and MySQL by Lenz Grimmer We also hosted a successful Oracle Linux Pavilion with 11 of our key partners - Beyond Trust, Centrify, Data Intensity, Fujitsu, HP, LSI, Mellanox, Micro Focus, NetApp, QLogic and Teleran showcased their solutions for Oracle Linux and Oracle VM. Here are some videos from the Oracle Linux Pavilion. Centrify covers Oracle Linux solution they offer at Oracle Linux PavilionMellanox talk about their solution at Oracle Linux Pavilion Eric Pan covers Micro Focus products at Oracle Linux Pavilion There's also collection of the keynotes and executive sessions as on-demand videos posted  here . We hope you find this information useful and look forward to seeing at Oracle OpenWorld 2013! ORACLE LINUX TEAM

  Read the article

• Oracle Linux Pavilion is Back for Oracle OpenWorld

  - by Oracle OpenWorld Blog Team

  By Zeynep Koch Back by popular demand, Oracle will again host the Oracle Linux Pavilion at Oracle OpenWorld from October 1-3. The pavilion will be located in the Exhibition Hall at Moscone South, Booth 1033, next to the Oracle DEMOgrounds and Oracle Linux demopods. At the pavilion a select group of ISVs, IHVs, and SIs will showcase their products that have been Oracle Linux- and/or Oracle VM-certified. These certified products enable customer applications to run faster, thereby saving money.Partners exhibiting their solutions in the Oracle Linux Pavilion include: BeyondTrust: context-aware security intelligence for dynamic IT infrastructures such as cloud, mobile, and virtual technologies Centrify: control, secure, and audit access to cross-platform systems, mobile devices, and applications Data Intensity: cloud services and application management Fujitsu: technology platforms, private cloud, services, ubiquitous and device solutions HP: converged cloud, converged infrastructure, application transformation, and information optimization LSI: intelligent solid-state storage solutions for breakthrough database acceleration Mellanox: InfiniBand and Ethernet end-to-end server and storage interconnect solutions and services for data centers Micro Focus: mainframe solutions, application modernization and development tools, software quality tools NetApp: storage and data management QLogic: high performance networking Teleran: BI and data warehouse management solutions for Oracle Exadata Database Machine and Oracle Database Be sure to pick up your free Oracle Linux and Oracle VM DVD Kit if you visit one of these partners. We look forward to seeing you at the pavilion.

  Read the article

• Direct IO enhancements in OVM Server for SPARC 2.2(a.k.a LDoms2.2)

  - by user12611315

  The Direct I/O feature has been available for LDoms customers since LDoms2.0. Apart from the latest SR-IOV feature in LDoms2.2, it is worth noting a few enhancements to the Direct I/O feature. These are: Support for Metis-Q and Metis-E cards. These cards are highly requested for support and are worth mentioning because they are the only combo cards containing both FibreChannel and Ethernet in the same card. With this support, a customer can have both SAN storage and network access with just one card and one PCIe slot assigned to a logical domain. This reduces cost and helps when there are less number of slots in a given platform. The following are the part numbers for these cards. I have tried to put the platforms on which each card is supported, but this information can get quickly outdated. The accurate information can be found at the Support Document.  Card Name  Part Number  Platforms Metis-Q: StorageTek Dual 8Gb Fibre Channel Dual GbE ExpressModule HBA, QLogic SG-XPCIEFCGBE-Q8-N  SPARC T3-4, T4-4 Metis-E: StorageTek Dual 8Gb Fibre Chanel Dual GbE ExpressModule HBA, Emulex SG-XPCIEFCGBE-E8-N SPARC T3-4, T4-4  Additional cards added to the portfolio of supported cards. This is mainly Powerville based Ethernet cards, the part numbers for these cards as below:  Part Number  Description  7100477 Sun Quad Port GbE PCI Express 2.0 Low Profile Adapter, UTP  7100481 Sun Dual Port GbE PCI Express 2.0 Low Profile Adapter, MMF  7100483 Sun Quad Port GbE PCI Express 2.0 ExpressModule, UTP  7110486 Sun Quad Port GbE PCI Express 2.0 ExpressModule, MMF    Note:  Direct IO feature has a hard dependency on the Root domain(PCIe bus owner, here Primary domain). That is, rebooting the Root domain for any reason may impact the logical domains having PCIe slots assigned with Direct IO feature. So rebooting a root domain need to be carefully managed. Also apply the failure-policy settings as described in the admin guide and release notes to deal with unexpected cases.

  Read the article

• The Oracle Enterprise Linux Software and Hardware Ecosystem

  - by sergio.leunissen

  It's been nearly four years since we launched the Unbreakable Linux support program and with it the free Oracle Enterprise Linux software. Since then, we've built up an extensive ecosystem of hardware and software partners. Oracle works directly with these vendors to ensure joint customers can run Oracle Enterprise Linux. As Oracle Enterprise Linux is fully--both source and binary--compatible with Red Hat Enterprise Linux (RHEL), there is minimal work involved for software and hardware vendors to test their products with it. We develop our software on Oracle Enterprise Linux and perform full certification testing on Oracle Enterprise Linux as well. Due to the compatibility between Oracle Enterprise Linux and RHEL, Oracle also certifies its software for use on RHEL, without any additional testing. Oracle Enterprise Linux tracks RHEL by publishing freely downloadable installation media on edelivery.oracle.com/linux and updates, bug fixes and security errata on Unbreakable Linux Network (ULN). At the same time, Oracle's Linux kernel team is shaping the future of enterprise Linux distributions by developing technologies and features that matter to customers who deploy Linux in the data center, including file systems, memory management, high performance computing, data integrity and virtualization. All this work is contributed to the Linux and Xen communities. The list below is a sample of the partners who have certified their products with Oracle Enterprise Linux. If you're interested in certifying your software or hardware with Oracle Enterprise Linux, please contact us via [email protected] Chip Manufacturers Intel, Intel Enabled Server Acceleration Alliance AMD Server vendors Cisco Unified Computing System Dawning Dell Egenera Fujitsu HP Huawei IBM NEC Sun/Oracle Storage Systems, Volume Management and File Systems 3Par Compellent EMC VPLEX FalconStor Fusion-io Hitachi Data Systems HP Storage Array Systems Lustre Network Appliance OCFS2 PillarData Symantec Veritas Storage Foundation Networking: Switches, Host Bus Adapters (HBAs), Converged Network Adapters (CNAs), InfiniBand Brocade Emulex Mellanox QLogic Voltaire SOA and Middleware ActiveState ActivePerl, ActivePython Tibco Zend Backup, Recovery & Replication Arkeia Network Backup Suite BakBone NetVault CommVault Simpana 8 EMC Networker, Replication Manager FalconStor Continuous Data Protector HP Data Protector NetApp Snapmanager Quest LiteSpeed Engine Steeleye Data Replication, Disaster Recovery Symantec NetBackup, Veritas Volume Replicator, Symantec Backup Exec Zmanda Amanda Enterprise Data Center Automation BMC CA Unicenter HP Server Automation (formerly Opsware), System Management Homepage Oracle Enterprise Manager Ops Center Quest Vizioncore vFoglight Pro TeamQuest Manager Clustering & High Availability FUJITSU x10sure NEC Express Cluster X Steeleye Lifekeeper Symantec Cluster Server Univa UniCluster Virtualization Platforms and Cloud Providers Amazon EC2 Citrix XenServer Rackspace Cloud VirtualBox VMWare ESX Security Management ArcSight: Enterprise Security Manager, Logger CA Access Control Centrify Suite Ecora Auditor FoxT Manager Likewise: Unix Account Management Lumension Endpoint Management and Security Suite QualysGuard Suite Quest Privilege Manager McAfee Application Control, Change ControlIntegrity Monitor, Integrity Control, PCI Pro Solidcore S3 Symantec Enterprise Security Manager (ESM) Tripwire Trusted Computer Solutions

  Read the article

• Understanding Linux SCSI queue depths

  - by Troels Arvin

  I'm experimenting with the effects of different SCSI queue depth values on a Dell server running CentOS Linux 5.4 (x86_64). The server has two QLogic QLE2560 FC HBAs connected via multipathing to a storage system. The storage system has allocated two LUNs to the server, each connected through four paths in an active-active-active-active round-robin configuration. All in all, the two LUNs exist as eight /dev/sdX devices, represented by two devices in /dev/mpath. I currently adjust the queue depth values in /etc/modprobe.conf and check the result (after rebooting) by looking in the seventh column of /proc/scsi/sg/devices. Two questions related to that: Is there a way to adjust queue depths without rebooting or unloading the qla2xxx kernel module? E.g., can I echo a new queue depth value into some /proc or /sys-like file to update the queue depth? If I set the queue depth to 128, is that 128 in total for all devices handled by the qla2xxx module?, or 128 for each HBA? (256 in total), or 128 for each of the eight /dev/sdX devices (1024 in toal)?, or 128 for each of the two /dev/mpath/... devices (256 in total)? This is important for me to know so that my server doesn't flood the storage system, affecting other servers connected to it.

  Read the article

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

1 2  | Next Page >