Search Results

Search found 10 results on 1 pages for 'rv082'.

Page 1/1 | 1 

• Connect ADSL modem SMC7904WBRA-N to CISCO RV082

  - by Cy.

  I have a SMC7904WBRA-N ADSL modem/router that connects to the internet with a static IP given by the provider. I've received a RV082 to create a VPN connection which is having problems to connect to the remote VPN Server. After many tries we deduced that the SMC7904WBRA-N is being problematic with the NAT and I have been suggested to put the SMC router into the appropriate DSL bridging mode so the RV082 gets direct access to internet with the static IP. Can you give me any hints on how could this be done? Which mode is that?

  Read the article

• SNMP counter issues with cisco RV082

  - by Chance

  Does anyone else poll this router with SNMP? We are using firmware version: 2.0.0.19-tz We are having problems with the traffic counters, some of them appear to be implemented as 16 bit counter instead of 32 bit counters. The reason this is causing problems is that they roll over (at 65,000) to 0 in less than our minute polling cycle, really skewing our metrics. The counter for the Lan (interface 2) seems to be functioning properly, however interfaces 3 and 4 (WAN and DMZ / WAN2) rollover at 65000. Tue May 11 08:38:31 EDT 2010 IF-MIB::ifInOctets.1 = Counter32: 137634 IF-MIB::ifInOctets.2 = Counter32: 1865677943 IF-MIB::ifInOctets.3 = Counter32: 12450 IF-MIB::ifInOctets.4 = Counter32: 49354 Look at counter IF-MIB::ifInOctets.4 5 seconds later: Tue May 11 08:38:36 EDT 2010 IF-MIB::ifInOctets.1 = Counter32: 137634 IF-MIB::ifInOctets.2 = Counter32: 1865836207 IF-MIB::ifInOctets.3 = Counter32: 13167 IF-MIB::ifInOctets.4 = Counter32: 12900 Any suggestions? Seems like a bug to me, however I just wanted to make sure I wasn't crazy.. Thanks!

  Read the article

• VPN Device behind router/firewall

  - by David Steven

  ROUTER A: Peplink 310 serving as the gateway/router/firewall at one location. ROUTER B: Linksys RV082 serving as the gateway/router/firewall at another location. I want to VPN these two locations together. The Peplink has a PPTP server and has proprietary site-to-site vpn if you had another peplink device. The Linksys has an IPsec vpn server. VPN A: I also have another spare linksys rv082. I'm trying to setup the other rv082 (VPN A) behind the peplink (ROUTER A) and get VPN A to talk to ROUTER B. I setup VPN A with a lan ip address and plugged one of it's LAN ports into the LAN. I was able to get to it's web interface fine. On ROUTER A I one-to-one nat mapped one of our public ip's to the LAN IP for VPN A. I opened TCP 50-51 and UDP 500 to VPN A. I configured the VPN settings on VPN A to connect to ROUTER B. I did the opposite for ROUTER B. But the vpn doesn't connect. Then I tried pluging VPN A's wan port into the lan, and gave it another LAN IP. I thought perpahs VPN A didn't want to send VPN traffic out over the LAN and wanted do send it over it's WAN. The vpn still doesn't connect. It what I'm trying to do even possible?

  Read the article

• VPN - Cisco 2800 Series Router and Cisco ASA

  - by NickToyota

  What I currently have: Windows 2003/2008 servers supporting a 150 user environment. Linksys RV082 Router (HQ) and RV042 (satellite) routers Site to Site VPN Tunneling to 5 satellite (< 10 user) offices What I need: End-user VPN allowing myself and users to connect remotely to my network I need to replace our current routers and have been recommended the 2811 Router. Can this router alone be enough to get what I need (VPN tunnelling for users and site to site VPN) or will I require purchasing an additional ASA appliance?

  Read the article

• How to bridge multiple wireless access points (and internet entry points) into one network

  - by amccormack

  I have two DSL lines coming in to wireless access points and then running to a RV082 Gateway/Bridge. The gateway then runs to a switch, which runs to multiple PCs and a Printer (See picture below). Normally, I would set up the wireless access points behind the gateway, but they are also the modems for the dsl. I have found that I can not print to the network printer if I am connected to the wireless network, but only if I am connected to the wired network. How can I configure the Gateway and APs (Routers) so that the PCs and Printer are all on the same internal network? I have tried turning DHCP off or redirect on the APs and redirect them to the Gateway. However, neither of these worked. Furthermore, I tried pinging the Gateway from the AP but got no response.

  Read the article

• Blocked connections passing through firewall. What is wrong?

  - by Kiranu

  In our company we have a small business router (Cisco RV082) on which we are using its standard configuration (block all incoming traffic). We also have an SMTP relay configured (using WS2008R2) so that our internal applications can send email through google apps (which requires authentication). The thing is that the server was being used to send spam. We fixed the problem by only allowing the server to relay email from our internal IP address range (10.0.0.0/16). My concern is that there was a way by which external IPs connected to the network and that underlying problem has not been fixed, but I cannot imagine how these machines connected. Any thoughts?

  Read the article

• Proper Network Infastructure Setup DMZ, VPN, Routing Hardware Question

  - by NickToyota

  Greetings Server Fault Universe, So here's a quick background. Two weeks ago I started a new position as the systems administrator for an expanding health services company of just over 100 persons. The individual I was replacing left the company with little to no notice. Basically, I have inherited a network of one main HQ (where I am situated) which has existed for over 10 years, with five smaller offices (less than 20 persons). I am trying to make sense of the current setup. The network at the HQ includes: Linksys RV082 Router providing internet access for employees and site to site VPN connecting the smaller offices (using an RV042 each). We have both cable and dsl lines connected to balance traffic (however this does not work at all and is not my main concern right now). Cisco Ironport appliance. This is the main gateway for our incoming and outgoing emails. This also has an external IP and internal IP. Lotus domino in and out email servers connected to the mentioned Cisco gateway. These also have an external IP and internal IP. Two windows 2003 and 2008 boxes running as domain controllers with DNS of course. These also have both an external IP and internal IP. Website and web mail servers also on both external and internal IPs. I am still confused as why there are so many servers connected directly to the internet. I am seriously looking to redesign this setup with proper security practices in mind (my highest concern) and am in need of a proper firewall setup for the external/internal servers along with a VPN solution about 50 employees. Budget is not a concern as I have been given some flexibility to purchase necessary solutions. I have been told Cisco ASA appliance may help. Does anyone out in the Server Fault Universe have some recommendations? Thank you all in advance.

  Read the article

• RRAS with DHCP when the IP pool is on a different subnet

  - by John B

  I run a small business network and the last couple of days I have been setting up some equipment to add VPN capabilities to our network. I've got the following set up: Windows 2008 R2 with RRAS - 172.22.200.50 Cisco RV082 router - 172.22.100.1 / 172.22.200.1 The Cisco router only support DHCP on a single class C network; 172.22.100.0/24. On the Cisco router I have set up an additional subnet; 172.22.200.0/24. The DHCP range is 172.22.100.200-254 When a PPTP connection comes in to the router, it is forwarded to my RRAS at 172.22.200.50. If I configure RRAS to assign IPs from a static pool on the 172.22.200.0/24 subnet everything works fine except the DNS suffix / search domain. However, if I set RRAS to use DHCP I am no longer able to contact any devices on the network. The IP I receive is on a different subnet (172.22.100.0/24). Is it possible to still use DHCP as the method of ip assignment in RRAS, even when the IP adresses assigned are in a different subnet? If yes, what piece of configuration am I missing to fix the VPN connection issues mentioned in the paragraph above. The reason I want RRAS with DHCP to work is because from what I have understood, this is the "only" way to hand out a DNS suffix to VPN clients. Any help on this matter is greatly appreciated!

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• Strange network issue (ZIP file fails CRC test over VPN)

  - by Joe Schmoe

  We have a server in the office running Windows Server 2003 Our office is connected to our datacenter via hardware VPN (Linksys RV082 router in the office to CISCO router in the datacenter). There is a job that runs on the server in the office that does following: ZIP certain files from the server using 7Zip, copy ZIP file to a network share in the office and verify ZIP integrity, copy ZIP file to a network share in the data center and verify ZIP integrity. Problem is - verifying ZIP integrity for the file in the data center always fails. However, if I run 7Zip on the server in data center that exposes that share ZIP file verifies just fine, so it is not actually corrupted during copy operation. Additionally, I tried running ZIP on other computers in the office to verify ZIP file on datacenter file share and it verifies OK. I tried plugging server to the same network port where my workstation is connected using different cable (my workstation doesn't exhibit this problem) and ZIP verification still fails. So the problem is local to that specific server. On network adapter properties for the server in question there is no "Advanced" tab where one can usually configure a lot of network settings. Network card driver is up to date (Windows Update doesn't find anything newer and Lenovo website doesn't have any drivers for Windows 2003 for this computer model). Is there any other way to configure network setting via command line? What settings could be relevant to this problem?

  Read the article

1