Search Results

Search found 28 results on 2 pages for 'vmotion'.

Page 1/2 | 1 2  | Next Page >

  • Virtual NIC on VM couldn't ping externally after Vmotion

    - by ToreTrygg
    Today I vmotioned 5 MS SQL 2005 servers over to a new DRS Cluster. All SQL servers use the "Production_LAN" network and a single virtual NIC of type "VMXNET 3". The first 4 SQL VM (Windows 2003 Standard or Enterprise x32 bit) vmotioned over without a hitch. The last SQL VM I vmotioned (Windows 2003 Standard x64 bit R2) vmotioned over without error, but I upon completion, I could no longer ping the VM. I went into the VM and could not even ping the gateway, however I could ping the loopback. This SQL server is extremely busy in comparison with the previous 4 VM's. I restarted the server and it came back up with the virtual nic working just fine. The build of both servers (vmotioner and vmotionee) is ESX 4.0.0 175625 - So, pre-update 1. Should I suspect the network switch/VM for possibly not updating the mac table on the switch? Anybody else ever have this issue or know what may have caused it? Thank you!

    Read the article

  • Loss of feature set with VMware EVC

    - by Peter
    If I have two machines both 3rd Generation AMD Opteron, one Shanghai & one Istanbul and I can vMotion between them. Does it buy me anything to enable EVC at the 3rd Generation AMD level? Will I lose any CPU features? My thoughts are, I can enable EVC 3rd Generation with running VMs and I can't enable 2nd Generation EVC with running VMs. I figure there won't be a lose in any features because if there was a reduction in feature set then I couldn't enable EVC with running VMs.

    Read the article

  • EMC ESRS stops working when it is VMotioned

    - by makerofthings7
    EMC is on site and told me: The ESRS SAN monitoring solution will cease to function if that host is VMotioned In case anyone doesn't know, the ESRS is a dial home solution that works over IP. An EMC SecureID is required to add or modify the list of devices that are monitored. The ESRS software is installed on the customer premises. Question If ESRS truly fails to work, as the EMC engineer stated, and based on our customer experience, what is it within VMWare that is exposed to the virtualized host that allows this behavior to happen?

    Read the article

  • VMware networking - PortChannel or not?

    - by dunxd
    My ESX hosts each have 8 NICS. I have set up 2 NICs for our iSCSI SAN - each is connected to a different SAN switch. 2 NICs are set up for vMotion and Service Console - these are each connected to a different core switch (ports are trunked with VLANs dedicated to vMotion and Management) I now have four ports left over. Currently we have these set up each going into our default VLAN. Two NICs are connected to one core-switch and two are connected to the other. We decided to aggregate the connections to each switch - so they are teamed at the vswitch end, and port channelled at the physical switch end. I am now reading that port channelling these connections is not particularly useful, perhaps even over complicating things. Is there a particular problem with using port channels for VMware? What method provides the best balance between redundancy and performance?

    Read the article

  • VLAN ID 4095 for guest VLAN tagging

    - by user121282
    Just want to know if it's true that if you use the VLAN ID 4095 for guest VLAN tagging, then vMotion will not work correctly as there is nowhere to pass back the reverse arp to? So, the problem we have noticed is when we have vmotioned VM's that are tagged on our trunk network, you cannot ping them from anywhere between 30-300 seconds. The hosts don't know which VLAN the guest is on. Is this right and also the correct behaviour? Thanks

    Read the article

  • HP DL160 vs DL360 for virtualization

    - by Chris
    Hi, We're planning to consolidate our infrastructure (a dozen servers). We'll buy two or three identical new servers who will be setup as a XenServer pool. Load balancing and HA tools will monitor the pool and vMotion VMs in case of failure/overload. I know that the DL100 series of HP servers is cheaper than the DL300 serie (in every sense of the word). As we don't need local storage (we have a SAN) and can live with a temporary down server (provided that Xen Server HA tools work as advertized), what are the downsides going with the DL100 serie ? Thanks, Chris

    Read the article

  • What kind of storage do people actually use for VMware ESX servers?

    - by Dirk Paessler
    VMware and many network evangelists try to tell you that sophisticated (=expensive) fiber SANs are the "only" storage option for VMware ESX and ESXi servers. Well, yes, of course. Using a SAN is fast, reliable and makes vMotion possible. Great. But: Can all ESX/ESXi users really afford SANs? My theory is that less than 20% of all VMware ESX installations on this planet actually use fiber or iSCS SANs. Most of these installation will be in larger companies who can afford this. I would predict that most VMware installations use "attached storage" (vmdks are stored on disks inside the server). Most of them run in SMEs and there are so many of them! We run two ESX 3.5 servers with attached storage and two ESX 4 servers with an iSCS san. And the "real live difference" between both is barely notable :-) Do you know of any official statistics for this question? What do you use as your storage medium?

    Read the article

  • VMware Virtual vCenter and High Availability

    - by rufo
    To continue with this question: Should be Vmware vCenter server high available? According to the response there even if vCenter is down HA will continue to work. So, if my vCenter is a VM, using the express sql edition in the same VM, and that VM is hosted in the same cluster it manages (and the cluster is setup for HA): Am I correct to assume that if the host that hosts the vCenter goes down HA will vmotion the vCenter VM to another host and it will continue to function? BTW: my environment is small, two ESXi 5.0 hosts, with about 50 VMs, using iSCSI shared storaged for everything.

    Read the article

  • LUNS access issue in ESX4 Cluster server

    - by rmustafa
    HI, I've created volumes in equallogic in PS 6000 XV(having 2 member which is in 1 pool), checked & those volumes can be easily detected my ISCSI software in windows. But the problem with ESX , not able to see the assigned disk on ESX server, I can explain what I've done: 1.Created Cluster with enabled HA & DRS 2.Added 3 ESX4 HOST 3.Added VMkernel & configured in all 3 ESX4, enabled vmotion & FT on the same adapter. 4.went to iSCSI storage adapter properties, enabled iSCSI 5.Trying to discover the available storage with the controller IP on dynamic discovery, but not able to see the assigned storage Note: the same volume is accessed to windows that means there is no issue from storage , am I right ???? Note: I wanted to mount the same volume in all 3 ESX host. Please suggest .... Thanks & Regards, Rashid Mustafa

    Read the article

  • Brocade 200E Switch - Fibre Channel

    - by Arthor
    What I have: Fujitsu-Siemens PRIMERGY BX600 Brocade 200E (16 port, 4gbit fibre). My question: Imagine a QNAP with a fiber 10GBIT card connected to the Brocade 200E (16 port, 4gbit fibre). Would this work; would the card drop down to 4GBIT? Are 10GBIT fiber cards backwards completable. Update. I have the specs of my server now.... Fujitsu-Siemens PRIMERGY BX600 S3 Blade Ecosystem Blade Chassis comprising; 2 x A3C40073243 Blade Management modules 2 x A3C40089238 GBE Switch Blade SB9F 30/12 2 x A3C40085736 4Gb 10 port pass through blades 1 x A3C40083767 Digital KVM Modules 2 x A3C40073245 Fan enclosures + cooling fans 4 x A3C40073262 Power Supplies My Goals and Objectives To have a blade system in place for 8 blades for video rendering, the other 2 for database and scripts etc The system will be built on VMWARE ESXi 5 Use ISCSI on the QNAP to support HA and vmotion if needed Users to access the qnap for video editing QANAP has 12 drive (2 x (6 HDD in RAID 10)

    Read the article

  • Does Citrix XenServer have storage Migration

    - by Entity_Razer
    I'm trying to find out. I can't seem to find a defenitive yes / no answers so I thought I'd ask the ServerFault community this simple question: Does XenServer (in any version) support Storage migration such as VMWare's Storage VMotion capability, or Hyper-V's storage migration ? I'm trying to do a comparative study of all platforms but I can't find a website (preff. Citrix supported or any other "legit" source) where it say's a defenitive yes or no. Anyone able to answer this one for me ? Cheers !

    Read the article

  • ESXi disaster recovery plan

    - by Marlin
    I have a Vmware infrastructure where I am using the free version of Esxi 5 . I cannot as a result use vmotion and the other cool features that come with a paid ESXI. I am using snapshots for the backups but they are stored on local hard drive. I need a better backup scenario where I can recover in the event of a harddrive failure. I tried openfiler but could not get it right. What backup method can I try given my situation?

    Read the article

  • High Availability Clustering and Virtualization

    - by tmcallaghan
    I'm trying to understand how the various virtualization vendors (specifically Amazon EC2, but also VMware and Xen) enable software vendors to provide a real HA solution in the environment where the servers are virtualized. Specifically, if I'm running any HA application (exchange, databases, etc) I need to ensure that my redundant virtual "servers" aren't located on the same physical server. Using in-house virtualization solutions (VMware, Xen, etc) I can provision accordingly as well as check the virtual - physical arrangement. I could, however, accidentally "vmotion" to the same physical hardware. With EC2, I don't even have the ability at provision time to select different physical servers. Since their Cluster Compute Instances are 1 virtual server per physical server it seems to be the only way to guarantee I don't have a false sense of redundancy. Any ideas or thoughts would be helpful. What are others doing about this problem? If the vendors provided an API where I could get something as simple as a unique physical system identifier I could at least know if I'm going to have an issue. -Tim

    Read the article

  • vSwitch configuration with 12 uplinks

    - by Joshua
    I have been doing a lot of research on vSwitch configurations, but I think I am more confused now after all of the reading that I have done. So here is my situation 3 ESX Hosts (12 nics each), 1 iSCSI SAN, 2 Force 10 switches. Should I create individual vSwitches for MGMT, vMotion, VM, and SCSI traffic? or do I need to group anything together in the same vSwitch? I am going to have 4 vLANS total, one for each of those items, do I need to do any trunking on the physical switch or just assign the correct vLAN to each physical switch port?

    Read the article

  • Does Citrix XenServer have storage Migration [closed]

    - by Entity_Razer
    I'm trying to find out. I can't seem to find a defenitive yes / no answers so I thought I'd ask the ServerFault community this simple question: Does XenServer (in any version) support Storage migration such as VMWare's Storage VMotion capability, or Hyper-V's storage migration ? I'm trying to do a comparative study of all platforms but I can't find a website (preff. Citrix supported or any other "legit" source) where it say's a defenitive yes or no. Anyone able to answer this one for me ? Cheers !

    Read the article

  • ArchBeat Link-o-Rama for 2012-09-25

    - by Bob Rhubart
    Oracle 11gR2 RAC on Software Defined Network (SDN) | Gilbert Stan "The SDN [software defined network] idea is to separate the control plane and the data plane in networking and to virtualize networking the same way we have virtualized servers," explains Gil Standen. "This is an idea whose time has come because VMs and vmotion have created all kinds of problems with how to tell networking equipment that a VM has moved and to preserve connectivity to VPN end points, preserve IP, etc." H/T to Oracle ACE Director Tim Hall for the recommendation. ServerSent-Events on WebLogic Server | Steve Buttons "The HTML5 ServerSent-Event model provides a mechanism to allow browser clients to establish a uni-directional communication path to a server, where the server is then able to push messages to the browser at any point in time," explains Steve "Buttso" Buttons. Focus on Architects and Architecture This handy guide for sessions and other activities at Oracle OpenWorld 2012 focuses on IT architecture in all its many facets and permutations. Operating System Set-up for WebLogic Server | Rene van Wijk Oracle ACE Rene van Wijk shows you how to set-up an operating system for WebLogic Server. "We will use VMware as our virtualization platform and use CentOS as the operating system," says van Wijk. "We end the post by showing how the operating system can be tuned when running a Java process such as WebLogic Server." Free eBook: Oracle SOA Suite - In the Customer's Words If you find yourself in the position of having to sell the idea of Service-oriented Architecture to business stakeholders this free e-book may come in very handy. Check out "Oracle SOA Suite: In the Customer's Words. (Registration / Oracle.com login required.) Thought for the Day "The first rule of any technology used in a business is that automation applied to an efficient operation will magnify the efficiency. The second is that automation applied to an inefficient operation will magnify the inefficiency." — Bill Gates Source: BrainyQuote.com

    Read the article

  • vmdk Recovery after migration from 3.5 to 4 and fallback tentative.

    - by olgirard
    Hy, I've tryed to migrate some VM from my 3.5i environment to a brand new vSphere 4.0 U1. The two platforms are running simultaneously, sharing the same SAN. I Migrate my VM by stopping it, unregistering in vcenter (esx ver. 3.5, i call it esx3), register in vSphere (esx ver. 4, i call it esx4), and migrate upgrade virtual hardware before powering it up (First mistake). vMotion was enabled on esx4, seem to be a second mistake. After a day or so, i encountred problems joigning the esx server (esx4) and decided to unregister my server for esx4 and fallback to esx3. esx3 refused to boot, i supposed this was due to virtual hardware in Version 7 so i recreated a new VM pointing to the vmdk of the old VM. Everithing seemed fine until i log into the server and discover that i was running on the original disk ith every snapshots ignored even those created on esx3. I tried to reboot VM on esx4 but VM doesn't power up because "The parent virtual disk has been modified since the child was created". I've got a copy of a later state of the drive but generated between two snapshots (ovf generated with canverter standalone) as a backup. Do i have a chance to recover at least some files on the virtual drive or (as i tink) all is played, i've done enought mistakes for this time. Thanks for your help.

    Read the article

  • Network Misconfiguration when adding first host to new vSphere cluster

    - by dunxd
    I am building a new vSphere cluster from scratch. I have installed ESXi on the first host, and built a vCenter server on a VM residing on that host (storage is on the local hard drive, although we have iSCSI targets which I can reach from the host). The cluster is configured for HA. When I try and add the host to the cluster, I get an error at the point where HA is configured - Cannot complete the . I have stripped the network configuration of the host down to the most basic - a single NIC attached to a single vSwitch - this is running the VMKernel Port on VLAN 8 - that is our Management VLAN. The vCenter server will have a network address on this VLAN, so I also set the initial Virtual Machine Port Group to this VLAN, and connected the vCenter server NIC to this port group. I understand I can't connect the vCenter server to the VMkernel port group, but shouldn't I be able to connect the vCenter server to a Port Group in the same VLAN? If not, do I need to create a VLAN specifically for VMKernel Port Group? I plan to set up another port group for vMotion with a dedicated and isolated VLAN (i.e. VLAN isn't routed) so this wouldn't allow vCenter to communicate. Does anyone have any suggestions, or other ideas for what might be causing the problem. I've read through the documentation, but it isn't giving me any pointers, and the error message isn't helping me beyond telling me something is wrong with my network config.

    Read the article

  • iSCSI performance questions

    - by RyanLambert
    Hi everyone, apologies for the long-winded post in advance... Attempting to troubleshoot some iSCSI sluggishness on a brand new vSphere deployment (still in test). Layout is as such: 3 VSphere hosts, each with 2x 10GB NICs plugged into a pair of Nexus 5020s with a 10gig back-to-back between them. NICs are port-channeled in an active/active redundant fashion (using vPC-mac pinning for those of you familiar with N1KV) Both NICs carry service console, vmotion, iSCSI, and guest traffic. iSCSI is on a single subnet/single VLAN that is not routed through our IP network (strictly layer2) Had this been a 1gig deployment, we probably would have split the iSCSI traffic off onto separate NICs, but the price/port gets rather ridiculous when you start throwing 4+ NICs to a server in a 10gigabit infrastructure, and I'm not really convinced it's necessary. Open to dialogue/tech facts re: this, though. At this point even a single VM guest will boot slowly to iSCSI storage (EMC CX4 on the same Nexus 5020 10gig switches), and restores of VMs from iSCSI take about twice as long as we'd expect them to. Our server folks mentioned that if we split the iSCSI off onto its own NIC, performance seems significantly better. From a network perspective, I've run through the variables I can think of (port configuration errors, MTU problems, congestion etc.) and I'm coming up dry. There really is no other traffic on these hosts other than the very specific test being performed at the time. Important thing to note is that guest traffic works just fine... it seems storage is the only thing affected by whatever gremlin exists. Concluding that we're not 'overutilizing' the network infrastructure since we're doing hardly anything, I'm just looking for some helpful tips/ideas we can use to resolve this... preferably without hurling extra 10gig NICs that are going to sit around 10% utilization while we've got 70+% left on our others.

    Read the article

  • VMWare vSphere 5: 4 pNICs for iSCSI vs. 2 pNICs

    - by gravyface
    New SAN for me, never used before: it's an IBM DS3512, dual controller with a quad 1GbE NIC per controller that a client bought and needs help setting up. Hosts (x2) have 8 pNICs and while I usually reserve 2 pNICs for iSCSI per host (and 2 for VM, 2 for management, 2 for vMotion, staggered across adapters), these extra ports on the SAN have me wondering if storage I/O would be significantly improved with 2 additional NICs per host, or if the limitations of the vmkernel/initiator would prevent the additional multipaths from ever being realized. I'm not seeing alot of 4 pNIC iSCSI implementations per host; 2 is the de facto standard from what I've read/seen online. I could and probably will do some I/O testing, but just wondering if there's a "wall" that someone else has discovered long ago (i.e. before 10GbE) that makes a 4 NIC iSCSI per host setup somewhat pointless. Just to clarify: I'm not looking for a how-to, but an explanation (link to paper, VMWare recommendation, benchmark, etc.) as to why 2-NIC configurations are the norm vs. 4-NIC iSCSI configurations. i.e. storage vendor limitations, VMKernel/initiator limitations, etc.

    Read the article

  • OTN ArchBeat Top 10 for September 2012

    - by Bob Rhubart
    The results are in... Listed below are the Top 10 most popular items shared via the OTN ArchBeat Facebook Page for the month of September 2012. The Real Architects of Los Angeles - OTN Architect Day - Oct 25 No gossip. No drama. No hair pulling. Just a full day of technical sessions and peer interaction focused on using Oracle technologies in today's cloud and SOA architectures. The event is free, but seating is limited, so register now. Thursday October 25, 2012. 8:00 a.m. – 5:00 p.m. Sofitel Los Angeles, 8555 Beverly Boulevard, Los Angeles, CA 90048. Oracle Fusion Middleware Security: Attaching OWSM policies to JRF-based web services clients "OWSM (Oracle Web Services Manager) is Oracle's recommended method for securing SOAP web services," says Oracle Fusion Middleware A-Team member Andre Correa. "It provides agents that encapsulate the necessary logic to interact with the underlying software stack on both service and client sides. Such agents have their behavior driven by policies. OWSM ships with a bunch of policies that are adequate to most common real world scenarios." His detailed post shows how to make it happen. Oracle 11gR2 RAC on Software Defined Network (SDN) (OpenvSwitch, Floodlight, Beacon) | Gilbert Stan "The SDN [software defined network] idea is to separate the control plane and the data plane in networking and to virtualize networking the same way we have virtualized servers," explains Gil Standen. "This is an idea whose time has come because VMs and vmotion have created all kinds of problems with how to tell networking equipment that a VM has moved and to preserve connectivity to VPN end points, preserve IP, etc." H/T to Oracle ACE Director Tim Hall for the recommendation. Process Oracle OER Events using a simple Web Service | Bob Webster Bob Webster's post "provides an example of a simple web service that processes Oracle Enterprise Repository (OER) Events. The service receives events from OER and utilizes the OER REX API to implement simple OER automations for selected event types." Understanding Oracle BI 11g Security vs Legacy Oracle BI 10g | Christian Screen "After conducting a large amount of Oracle BI 10g to Oracle BI 11g upgrades and after writing the Oracle BI 11g book,"says Oracle ACE Christian Screen, "I still continually get asked one of the most basic questions regarding security in Oracle BI 11g; How does it compare to Oracle BI 10g? The trail of questions typically goes on to what are the differences? And, how do we leverage our current Oracle BI 10g security table schema in Oracle BI 11g?" OIM-OAM-OAAM integration using TAP – Request Flow you must understand!! | Atul Kumar Atul Kumar's post addresses "key points and request flow that you must understand" when integrating three Oracle Identity Management product Oracle Identity Management, Oracle Access Management, and Oracle Adaptive Access Manager. Adding a runtime LOV for a taskflow parameter in WebCenter | Yannick Ongena Oracle ACE Yannick Ongena illustrates how to customize the parameters tab for a taskflow in WebCenter. Tips on Migrating from AquaLogic .NET Accelerator to WebCenter WSRP Producer for .NET | Scott Nelson "It has been a very winding path and this blog entry is intended to share both the lessons learned and relevant approaches that led to those learnings," says Scott Nelson. "Like most journeys of discovery, it was not a direct path, and there are notes to let you know when it is practical to skip a section if you are in a hurry to get from here to there." 15 Lessons from 15 Years as a Software Architect | Ingo Rammer In this presentation from the GOTO Conference in Copenhagen, Ingo Rammer shares 15 tips regarding people, complexity and technology that he learned doing software architecture for 15 years. WebCenter Content (WCC) Trace Sections | ECM Architect ECM Architect Kevin Smith shares a detailed technical post covering WebCenter Content (WCC) Trace Sections. Thought for the Day "Eventually everything connects - people, ideas, objects. The quality of the connections is the key to quality per se." — Charles Eames (June 17, 1907 – August 21, 1978) Source: SoftwareQuotes.com

    Read the article

  • SQL Server Licensing in a VMware vSphere Cluster

    - by Helvick
    If I have SQL Server 2008 instances running in virtual machines on a VMware vSphere cluster with vMotion\DRS enabled so that the VM's can (potentially) run on any one of the physical servers in the cluster what precisely are the license requirements? For example assume that I have 4 physical ESX Hosts with dual physical CPU's and 3 separate single vCPU Virtual Machines running SQL Server 2008 running in that cluster. How many SQL Standard Processor licenses would I need? Is it 3 (one per VM) or 12 (one per VM on each physical host) or something else? How many SQL Enterprise Processor licenses would I need? Is it 3 (one per VM) or 8 (one for each physical CPU in the cluster) or, again, something else? The range in the list prices for these options goes from $17k to $200k so getting it right is quite important. Bonus question: If I choose the Server+CAL licensing model do I need to buy multiple Server instance licenses for each of the ESX hosts (so 12 copies of the SQL Server Standard server license so that there are enough licenses on each host to run all VM's) or again can I just license the VM and what difference would using Enterprise per server licensing make? Edited to Add Having spent some time reading the SQL 2008 Licensing Guide (63 Pages! Includes Maps!*) I've come across this: • Under the Server/CAL model, you may run unlimited instances of SQL Server 2008 Enterprise within the server farm, and move those instances freely, as long as those instances are not running on more servers than the number of licenses assigned to the server farm. • Under the Per Processor model, you effectively count the greatest number of physical processors that may support running instances of SQL Server 2008 Enterprise at any one time across the server farm and assign that number of Processor licenses And earlier: ..For SQL Server, these rule changes apply to SQL Server 2008 Enterprise only. By my reading this means that for my 3 VM's I only need 3 SQL 2008 Enterprise Processor Licenses or one copy of Server Enterprise + CALs for the cluster. By implication it means that I have to license all processors if I choose SQL 2008 Standard Processor licensing or that I have to buy a copy of SQL Server 2008 Standard for each ESX host if I choose to use CALs. *There is a map to demonstrate that a Server Farm cannot extend across an area broader than 3 timezones unless it's in the European Free Trade Area, I wasn't expecting that when I started reading it.

    Read the article

1 2  | Next Page >