Search Results

Search found 7992 results on 320 pages for 'hp power protector'.

Page 10/320 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Generic socket 940 CPU fan for HP XW9300 interchangeable with HP part number 411454-001

    - by ConcernedOfTunbridgeWells
    Hi, I'm trying to find a generic Socket 940 CPU fan that will fit the air duct in an XW9300. Note that two different CPU fan mounting schemes have been used on this machine. One has two grommets in the motherboard that the CPU fan screws into and the other has a plastic collar and base plate. The form factor I'm looking for is the former (see the picture below). Two HP part numbers for fans in this form factor are 411454-001 (shown below) and 416055-001. Note that the dimensions are important as the machine has an air duct that fits over the fan. Can anyone tell me the manufacturer and model of an equivalent generic part? Better yet, do you know somewhere (preferrably in the UK) from which such an item can be obtained?

    Read the article

  • How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

    - by Dave B.
    I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

    Read the article

  • gnome-power-manager is running while trying to log in. How to get rid of it?

    - by koushik
    After booting into the ubuntu login screen and clicking on my user name and entering the password, I get a dialog stating that gnome-power-manager is still running. The dialog presents 2 buttons, 1 to Cancel and other to Logout Anyway. This issue happens about 50% of the time and I don't remember doing anything related to power management recently. Also, even if I don't choose any option in the dialog it goes away after about 30s. This is happening on a desktop machine as well as a laptop. On the laptop I have configured power management for myself (not for gdm) whereas in desktop I have not configured power management for any user. This is only an annoyance but still I would like to fix it, especially on my desktop where I am interested in getting it auto-login ASAP into my userid. Any ideas why this could be happenning?

    Read the article

  • Ubuntu + Raid on HP proliant DL 160 G6

    - by Adam Matan
    Hi, I'm, trying to install Ubuntu 8.04 Server on an HP Proliant DL160 G6. The HP hardware is certified by Ubuntu for the 9.04 version, which I can't install due to company policy. The problem is that Ubuntu would not recognize the RAID 1+0 disk configured by the BIOS. The raid creates one ~470GB disk from two 500GB physical disks. Any ideas? Adam

    Read the article

  • Proliant Support Pack and Ubuntu on older HP Proliants

    - by snl
    We have a couple of oldish HP Proliant servers -- one DL385 G1 and one DL360 G5, to be exact -- that we'd like to upgrade from CentOS 5 to Ubuntu LucidLynx. The problem is that HP doesn't offer Ubuntu Proliant Support Packs for these particular models. Would you upgrade regardless, skipping the PSPs altogether? Are there alternative hardware monitoring tools that would match the functionality of the PSPs? Is there a hack to install the PSP RPMs on an Ubuntu system?

    Read the article

  • HP blade server: How many connection can be made between HP new gen 8 blades and an interconnect

    - by Dave T
    I am building a virtualized network on an HP C3000 with 460c Gen 8 blades and 2 HP L3 switch interconnects. I was advised to by a 1Gb 4-port 366M Mezzanine Adapter. That provides me 6 ethernet connections to each blade. I have been told that you can only make 2 connections to from each blade to each interconnect, but since I have to interconnectes and 6 ports I hope someone can tell me if I can make 3 connections from each server to each interconnect. I looking for the actual - thanks Dave

    Read the article

  • HP Proliant Servers - WMI query for system health

    - by Mike McClelland
    Hi, I want to query lots of HP servers to determine their overall health. I don't want to use any packages, or even SNMP - I want to query the server health from WMI and understand if a box is Green/Amber/Red - just like the HP Management Home Page. This MUST be possible - but I can't find any documentation... Oh yes, and the servers are running Windows Server 2003/8. Help!! Mike

    Read the article

  • NDMP NAS for HP EVA4400 SAN

    - by Sergei
    We use EMC Celerra filer for our EMC array and it supports NDMP.n remote site we have EVA4400 HP SAN and it seems that our only option for NAS is Windows Storage Option. What if we want to use NDMP?Surely HP should have something that match Celerra?

    Read the article

  • No video output and no status light on HP Proliant Microserver

    - by tombull89
    I have an issue with a "N40L" HP Proliant Microserver. When the server is powered on the power light turns green but the machine's status light (the HP logo on the front) stays off and there is no video output through th onboard VGA. The system fan kicks in and if connected to a network the link light shows activity. I have no extra boards (iLO card, graphics card) only 4GB PNY non-standard stick of RAM.

    Read the article

  • Windows 7 power management in Boot Camp mode

    - by qntmfred
    I have a Macbook Pro with Windows 7 installed in Boot Camp. I have serious problems with the power management and not sure why. I have the default Balanced power plan selected. Many times when I close the laptop and leave it for more than just a few minutes, when I open it back up, it does not awake immediately. I end up having to press the power button to get it to wake up. Sometimes this causes it to wake up in Windows mode, sometimes it reboots completely, sometimes the battery has been drained and Windows has to restart. Is this a common problem? Can I fix it?

    Read the article

  • What is the best position for power unit?

    - by guest86
    I would like to buy new computer case. Last time I bought a computer was in 2008 and many things have changed up to day. Many new computer cases have power unit placed down, on bottom. I'm thinking about buying some of those cases, but i'm not sure about something - if power unit is placed on the bottom it can't take away hot air from the case and pump it out right? All my PC parts are silent - CPU (E8200, placed below 12cm Nochtua fan of power unit) has heat-pipe cooler with Nochtua fan spinning at only 800rpms, GPU has cooler powered by 7V instead 12 and that's why i don't want to HAVE TO place another fan to pump out hot air instead of PU placed on top. That might make some noise. So i ask someone more experienced: if i buy some computer case with PU placed down, do i HAVE TO place some fan to pump out hot air?

    Read the article

  • Windows 7 USB power lose after a few seconds / minutes

    - by Stefan Dunn
    My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

    Read the article

  • Connecting mother board, power supply, and tower

    - by JordanD
    I am working on putting together a desktop for the first time and and ran into a problem, I am not sure how to connect the fans that came in my tower, my power supply, and connect them all to the mother board. Tower Mobo Power Supply There are 3 fans in the tower, each have 3 pin male and female connector that come connected, and 4 pin (larger?) male and female connector which are hanging. How would I go about connecting The fans together then to the power supply and mobo so it is easiest control (or suggest me a smart / better option). Pictures are from fans on HAF 922 Tower. Thanks

    Read the article

  • How to disable power to USB ports when laptop is in sleep mode

    - by Greg
    I have a Windows7 laptop with two external 2.5" HDDs and a cooling pad connected through USB ports. When I put the laptop to sleep, these devices are still powered on - the fan in the cooling pad is still spinning, the drives are still spinning. I want to set it all up so that they power down when in sleep. I tried setting the Allow the computer to turn off this device to save power option in the USB Root Hubs' Properties in Device Manager and enabling USB selective suspend in power options - it didn't work. As it's a laptop, BIOS options are extremely locked down, so I can't even see anything relevant to sleep in there. Is it even possible to do this?

    Read the article

  • Computer randomly shuts down with a fading alarm power button and CD drive

    - by Shad
    I am currently experiencing something very very odd. Having build my PC myself, I have never had any issues (or anything heat related). A few moments ago my computer shut down very randomly and everything goes blank, when I looked down on my case's power button it was fading on and off in such way I've had never seen before. I noticed the CD drive all of a sudden also started blinking randomly. What do you guys think this problem is related to? It is definitely not a overheating issue and I am pretty sure my 600 watt power supply didn't blow because right now I am able to turn it on and boot up the PC but 20 seconds later it shuts down (sometimes doesn't shut down for 2 minutes). I have no idea what this is... My specs are (built by myself): i5 3570k (unoverclocked) GTX 560ti Asrock Z77 Pro4-M motherboard 8GB Vengeance RAM 600W Corsair power supply 500GB of Seagate HD Case: Corsair Carbide 300R

    Read the article

  • Is the 4-pin PSU connector required? (Trying to connect a PSU to a mini case.)

    - by Geeks On Hugs
    I am trying to build a computer, placing an ASUS P8H67-I DELUXE in a custom retro C64 case. The case is an extra small form factor which can accomodate the Mini ITX board, but requires an external power supply, similar to the power-bricks that laptops use. I am looking at different power supplies and like these, but cannot figure out whether/how to power this system because they provide a 24-pin connector, but the motherboard has a 4-pin connector as well. Is the 4-pin connector optional or is it required? If it is required, how can I provide power for this system?

    Read the article

  • Dell Latitude E6400 power button and wireless not working or only working intermittently

    - by Droid
    The power button on the laptop stopped working randomly as of a day or two ago. I can only power the laptop on if its attached to a docking station, on which I can use the power button to turn on/off the laptop. Today the wireless card stopped working (the wifi light does not turn on, even after I turn on the wireless switch). What is the problem and how can I fix it? The laptop is about 1 year old. I have not dropped it, but do carry it around a good amount, including docking it/undocking it frequently.

    Read the article

  • HP Pavilion dv6000 QuickPlay power on

    - by user22559
    Hello I have a question for HP Pavilion dv6000 owners. If your laptop is powered down, and you press the QuickPlay button or the DVD button (NOT the power button), does the laptop start up? More info: I am asking this because I have got a hold of a broken HP dv6000. If I power it up, the power light lights up, and then the laptop powers down. It seems to be because of a broken motherboard. But the laptop does the same thing if you press the QuickPlay or DVD buttons, and I want to know if that's supposed to happen, or if it's something else that is wrong.

    Read the article

  • PC doesn't power up anymore

    - by Andrew
    I will tell you the story behind the problem. The computer needed to be reinstalled, it has 2 HDDs so I had to un-plug one to see which is which, to save as much data as possible. After unplugging the first one, it booted with the reinstallation CD, it wasn't the HDD I was looking for so I turned it off and unplugged the other one. After unplugging and turning on, right after booting test, the HDD was turned off, only the CPU fan was working. Turned it off with the power supply's button help, holding the power button didn't do it. And now it doesn't want to turn on anymore. I tried with another test power supply but the result is the same, doesn't want to turn on. Any idea?

    Read the article

  • Computer has power but won't boot

    - by John Isaacks
    When I power on my computer it will not boot. It will not even go into bios or anything. It is as if it is not powering on at all, however the decorative casing lights turn on and the PC is making noise (like from the fans). I am reluctant to think it is the power supply since some part are getting power. I do not know what it is though? For the couple days leading up to this, the computer would make a loud noise and the screen would stop displaying anything. I had to reboot to get it to work again. Now nothing happens when I boot, except the case lights come on and it sounds like some fans are coming on. Any ideas?

    Read the article

  • HP P212 hangs on Initializing

    - by user927586
    I'm in trouble... Server: HP Microserver N36L Storage: HP P212/256 with BBWC Drives: 4 WD 2 Tb While expanding the RAID 5 array from 3 to 4 drives, the server rebooted itself. Expansion was at 76%. Now at boot the P212 seems to hang on initializing. After some time screen resets and the server boots, but in the os (Windows Server 2008R2) the P212 has errors (error code 10) and it's not seen by the HP ACU. Whats' going on? It's trying to complete the expansion? It's trying to make all over the expansion? It's simply stuck? What should I do? I NEED the data on the array! PS In the server BIOS, on the hd boot priority, the server still reports the array logical drive... maybe it's a good sign... PPS I'm not at the server physical location, so I cannot tell if the drives in the array are being accessed (that would be the case if the controller it's redoing/completing the expansion process) or not right now. Bye Dario

    Read the article

  • Problem setting up HP PhotoSmart C4783

    - by ProfKaos
    I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >