Search Results

Search found 7992 results on 320 pages for 'hp power protector'.

Page 17/320 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Hp Procurve Switch : port filtered

  - by user117140

  My HP Procurve switch is blocking port 22 and I dont know how to unblock it.Please let me know From the server, see port 22 is blocked [root@server ~]#nmap -p22,80,443 10.247.172.70 Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-04-16 14:12 IST mass_dns: warning: Unable to determine any DNS servers. Reverse DNS is disabled. Try using --system-dns or specify valid servers with --dns_servers Interesting ports on 10.247.172.70: PORT STATE SERVICE 22/tcp filtered ssh ------------------> see 80/tcp filtered http 443/tcp filtered https This is blocked on cisco switch but I dont have any clue how this is done. I know that vlan is configured on switch. vlan 54 ip ospf 10.247.172.65 area 0.0.0.10 vrrp vrid 54 owner virtual-ip-address 10.247.172.65 255.255.255.192 priority 255 enable exit exit Please let me know how to unblock ssh port 22 access on this switch?

  Read the article

• Ubuntu/Linux version recommendation for HP dv6 3122TX?

  - by sanjayav

  I purchased a HP dv6 3122TX recently and after installing Ubuntu 10.10 64 bit I ran into multiple issues like, The wireless driver is not supported by Uubntu. (1) [The driver is RaLink RT3090 ] The ethernet stopped working sometimes for no reason [The driver is Realtek RTL8111/8168B ] "Corrupted low memory at ..." issue which is described as a kernel bug in Ubuntu support forums. (It started to take me to a terminal instead of the GUI and couldn't start x server after that) As I'm not an expert Ubuntu user I got fed up of all these issue and got back to Windows 7. But I need an Ubuntu installation up and running for my development work. What are your suggestions about a reasonable Ubuntu version that I should try? Or a different Linux variation? Should I stick to a 32-bit version? It'd be great anyone can give some advice on this issue.

  Read the article

• Suitable companion monitors for HP LP3065 30" primary monitor

  - by Bittercoder

  I have an HP LP3065 30" monitor - now I want to add a couple of companion screens to either side of it - I've heard to people suggesting 21" monitors in portrait mode - but it seems difficult to find a suitable panel these day, as 22" wide-screen monitors have become common, and I can't seem to find anything with a suitable 1600 pixel width. Can anyone recommend a suitable monitor, and suggest what criteria are best for picking a suitable monitor - what's important to consider - I'm thinking things like: Exact resolution match? Viewing angle? Small/thin bezel?

  Read the article

• HP Photosmart C5280 black ink not printing properly

  - by Andreas Strandfelt

  I just got a used HP Photosmart C5280 from my father in law. There is a problem with the black ink, though. Sometimes, it doesn't print and when it does, it's not really black. An example can be seen at the following link, where I created three black boxes on a Word page and printed. The outcome is somewhat blueish: Other tests with black text only come out as blank pages. I have tried using the print head cleaning utility from the menu of the printer as well as doing the cleaning myself with alcohol. Nothing has worked. Any ideas before I throw out the black cartridge?

  Read the article

• Installing Chrome OS on HP Pavilion

  - by Lenny K

  Trying to install Chrome OS on HP Pavillion tx1000. I changed the BIOS to boot from USB before hard drive, and created a bootable USB drive (SanDisk Cruzer 4GB). No matter how many ways I try to make the USB drive, the laptop hangs on the startup screen, and trying to open the Boot Order Options freezes on "Fixed disk 0: ...". On the other hand, without the USB plugged in, the computer continues, and displays "Initialized Mouse", and then onto the Boot Order Options. If you let it boot normally from the beginning, it starts up fine into Windows Vista. I am using Hexxeh's Chrome OS build. Here are the different methods I've tried for making the Bootable USB Drive: Hexxeh's Image Creator (for Mac) Making the USB device bootable (using these directions). I wrote the image using Win32DiskImager. Writing the image using Win32DiskImager (without making it bootable).

  Read the article

• HP DL380 G5 Predictive failure of a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• HP EX485 Media Server Keeps Powering Down & Restarting Automatically

  - by AWoo

  HP Home Media Server EX485 approx 3 years old. Unit suddenly powers itself off and restarts automatically as if the power button was pressed. Server restarts up OK for a few minutes and the cycle repeats itself again & again. Reseated all drives, check fans in chassis and they are OK (turning). Can login to server to see logs before it powers itself down again. Suggestions any help is appreciated on resolving this problem. Thanks.

  Read the article

• High IO latency on ESXi 4.1 on HP DL580 G7

  - by teddydestodes

  at my Company we were experiencing some weird spikes on IO latency on one of our ESXi instances. we've spend 24h figuring out whats wrong and no clue so far. after giving up we put all the disks into a different server (HP DL380 G7) with much less RAM and only one 6(HT) cores (from 12 on the DL 580) which run fine for about 2 hours. I dont know the specs for the DL380 but both servers have a Smart Array P410i with BBWC (the DL 580 has 1GB) Is it possible that one(or all) of the disks is failing without actually failing?

  Read the article

• HP 120 printer network install con windows 7 home

  - by Fusca

  I have a HP-1210 printer connected to a win 7 ultimate edt, this one, the printer-host, is logged to a domain. I also have a Windows 7 home edition (not logged into the domain) and I want to install the hp1210 printer. Other printers in the network (connected to the domain) are currently connected to the printer. In the Win 7 Home I ran the HP1210 installer but it doesn't find the printer over the network. Is this because this win7home is not connected to the domain? Is there any way to manually specify the printer path?

  Read the article

• HP DL380 Losing Drive Array

  - by jidl

  I have an HP Proliant DG380 G7 dropping one of it's arrays every hour, on the hour, for 2-5 minutes. The OS is SBS 2011 Standard, the servers runs Exchange, DC, files & Trend WFBS 8. I can watch the D Drive disappear for the duration of the problem - then it just comes back up and all is well again. There is no loss of network connectivity, although the mapped drives also disappear. We thought it might be to do with Sharepoint / VSS writers failing but it looks as though this is a symptom rather than cause. It survives a reboot. Any ideas as to what could be running on a regular schedule like this?

  Read the article

• How to change the default behavior of overrifing when GCC -fstack-protector-all is set?

  - by Vicente Botet Escriba

  I would like to use the GCC -fstack-protector-all option on release mode. The main issue is that when there is an override a code is built. I would like to plug something that will just dump the stack and let the program continue. Is there a way to do that?

  Read the article

• How to change the default behavior of overwriting when GCC -fstack-protector-all is set?

  - by Vicente Botet Escriba

  I would like to use the GCC -fstack-protector-all option on release mode. The main issue is that when there is an override a code is built. I would like to plug something that will just dump the stack and let the program continue. Is there a way to do that?

  Read the article

• HP OfficeJet 5600 w/ Dlink DPR1260 not printing except from Notepad

  - by joelarson

  I have an OfficeJet5600 attached to a Dlink DPR1260 wireless print router. It has worked great for a long time. Today we had a power outage and the thing was inaccessible. I reset the DPR1260 and reinstalled drivers and soforth. I can now print from Notepad, but not from any Office programs, IE, or Chrome. I have toggled on and off many settings such as spooling/not spooling, etc. Nothing has helped. Any ideas? I have Windows Vista.

  Read the article

• Why did my power supply fry itself?

  - by ULTRA_POROV

  I am in europe. There was a switch on my psu that could switch the voltage between 230v and 130v (not 100% sure). In europe we use 230. I switched the psu to 110 and turned it on. Several sparks and a power failiure resulted, the psu was fried. Can someone explain why this happened. I was assuming that because the system was using 230 and the psu only draws 130 it would be safe cause it's less. I guess i was wrong. Can someone explain me the physics behind this.

  Read the article

• HP ProLiant Smart Array "lock up" code 0x11

  - by ewwhite

  I've a ProLiant DL580 G7 server that experienced a storage subsystem failure during production. The system appeared available and responded to pings, but all I/O access stalled (the system load must have been 100+). The ASR did not trigger at the specified watchdog timeout. I had to force a reboot from the ILO. During POST, I received the following error: A controller failure event occurred prior to this power-up. (Previous lock up code = 0x11) I haven't pulled the ADU report yet, but I'm curious as to what this error actually means. I was not responsible for the the installation, but can see that the firmware is very old. But if there's anything else I should know about the error, I'd like to know for the post-mortem report. edit - I should add that the server had 95 days of uptime prior to the lock up.

  Read the article

• How low-power can a home server get?

  - by Halik

  I've got quite simple question actually. How green, low-power and efficient x86 home server can I build using consumer parts with rather constrained budget. After looking through some Google hits I've found out that system based on dual-core atom, some modest mITX board (gigabit lan, integrated audio and gfx etc), one RAM module and one 'green' WD HDD, powered by picoITX PSU uses about 30W at idle up to 40 at load. Can you get lower (or how much lower) then that? Maybe some VIA nano chips, or single core atom? My home server would take care of some back-upping mixed with little ftp/http traffic.

  Read the article

• Laptop touchpad works incorrect when on power supply

  - by Ikke

  My original laptop adapter broke down, so I've baught a new one. It's a no-brand adapter from a dutch internet shop. The power of the new adapter is slightly more than the old adapter, but in my opinion that shouldn't be a problem. The laptop is a Toshiba Sattelite L40-15B. When the old adapter broke down due to short circuit, this laptop was connected. When the adapter is unplugged, the touchpad works correctly and smoothly. But as soon as it is connected, the cursor moves jumpy, and response badly. Does anyone know where this problem comes from, and if there's a solution?

  Read the article

• New power supply and now HDDs are not recognized

  - by Michael

  So I upgraded to a new X4 ULTRA power supply that was recommended to me by a local TigerDirect store. After installing it along with a new liquid cooling system, I booted it up and it automatically fried my CD Drive. After that I noticed that the OS wouldn't start and figured out that none of the 4 HDDs in my computer were being recognized by the BIOS. I feel them spool at a steady pace and have tried new cables and connections but to no avail. I triple checked all of the connections and cables and have no idea what is wrong. This isn't the first time I changed a PS or CPU cooling system but I am at a dead end. Any ideas, aside from buying a USB HDD reader and seeing if they are all fried? Also, this is a stock Gateway mobo with the mobo USB connections already dead. Could the new PS have fried the SATA connections??

  Read the article

• Can a power loss break an hard disk?

  - by dag729

  Today I was working when all of a sudden a power loss (in the entire house) occurs. I tried to reboot the machine but it states that there's an "Ebios error"; tried with an Ubuntu 9.04 live cd and while booting it states that there are various I/O errors on the first partition (the one with the boot sector). Now I managed to backup all of my data (using the live cd aforementioned) but I don't know if it'll worth the hassle of a reinstallation (and if it could do something useful) or if the only thing to do is to drop the hard disk as far as possible... Thanks in advance.

  Read the article

• Dell XPS M1330 - power cable pulled by accident and now it won't turn on

  - by jim

  I have a similar problem to what has been posted on this site about when I plug in my Laptop adapter the green light comes on as expected; but, when I plug it into the laptop it goes out. In my case, I know it's not the adapter because I have 2 and they both experience the same issue. I'm quite certain the problem is a short in the laptop. I was using the laptop today and the power cord was pulled out by accident and now i'm into this predicament. How or what do I check on the laptop to isolate the problem? Thanks!

  Read the article

• Re-cased my computer now the power plug keeps shorting

  - by dunc

  I've just re-cased my computer. I got the new case free and thought I'd be able to swap everything over myself but apparently I've done something wrong. I'm OK with components generally but wasn't totally confident about doing this. So, my question is, when setting up a new PC or moving old components into a new case, what could I have done which causes the power cable plug to short/fuse when I plug it in?. Is this likely to be an issue with the cables from my PSU, or could it be the internal case connectors? What steps would you take to diagnose the problem? I'd rather not start again if I don't have to...! Thanks in advance,

  Read the article

• Power outage, Server 2K3 remains on "applying computer settings"

  - by syuroff

  My reward for clicking the "test" button in the APC UPS software was that it completely cut the power to my SQL server. The server promptly rebooted, the SQL service is running (verified by the app on another server that queries it), but the GUI has remained on "applying computer settings" for 20 minutes and counting, and it forbids RDC connections. Since SQL is up, it is fulfilling its key role, but it's obviously not right. What step to take next? Wait longer? Hardware is a Dell Poweredge 2850, internal RAID10.

  Read the article

• How to fix Asus Eee PC 900 startup issues after failure?

  - by EBrown

  My Asus Eee PC 900 shows no signs of life. I push the power button and get no response from anything. No lights, no power, no boot-up screen. It has been like this since I received it from a friend. I asked her what happened and she said that smoke came from the keyboard, it shut down and hasnt turned on since. I have tried removing and cleaning the RAM, the computer charger still connects and works, but the battery receives no charge and the computer won't power on. Any ideas as to what is going on?

  Read the article

• Turn on PC power remotely through the Internet?

  - by W.N.

  I use SVN for my work at home and office, but I usually forget to commit the changes before shutdown. Therefore, I wish I could turn on my home/office PC at office/home. I already have TeamViewer installed on both PCs, so it will be okay as soon as the power is turned on. I have read many articles about this, I found both my PC and office computers support Wake-on-LAN. However, I don't know much about other config. And I need to turn on my computers through the Internet, not on LAN. My office Internet connection has static IP, however, my home Internet connection has dynamic IP, it changes as soon as I reset the modem, but it is not a big problem, I rarely turn the Internet modem off. And I don't have privilege to config office Internet connection, but I have Administration privilege on both PCs. Please give me details steps to turn on my office PC from home, and turn on my home PC from office.

  Read the article

• can power supply affect I/O

  - by user101289

  I have a dev server machine running Ubuntu 12.04. For a long while it's been throwing intermittent errors where it would suddenly tell me "File system is read only" or drop into a GRUB error console on boot. I've done disk checks, bad blocks, etc. and no real problems with the main SATA drive were detected. Finally the drive would not be detected at all-- but neither would other drives I plugged in (via SATA). I plugged the supposedly "bad" drive into another server and it worked fine, no issues, for days-- so I assumed the motherboard had a bad SATA controller, and replaced the motherboard with an identical model. I replaced the drive into the original machine with the new motherboard, rebooted-- and the same issues-- I/O errors, failure to read the drive at all, dropping into GRUB, etc. I'm wondering if there could be some other issue with this machine, that's not related to the drive-- possibly power supply? Thanks for ideas

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >