Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 10/778 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Ubuntu 12.10 no network and no graphics

    - by khasiKoMasu
    I recently upgraded Ubuntu 12.04 to 12.10 only to find out that it won't connect to any network, neither wired nor wireless and the graphics is messed up too as in a low screen resolution. For 12.04, my system was running perfectly. I don't know why upgrade messed it up so bad. Reinstalling the OS is an issue because I have set up a lot of development environments that I cannot afford to set it up again. Some of the outputs: lspci -nn | grep 0200 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) nm-tool NetworkManager Tool State: disconnected cat /etc/network/interfaces auto lo iface lo inet loopback sudo cat /var/log/syslog | grep etwork | tail -n20 Nov 2 13:50:22 Cobalt NetworkManager[978]: SCPlugin-Ifupdown: (-1240454760) ... get_connections (managed=false): return empty list. Nov 2 13:50:22 Cobalt NetworkManager[978]: Ifupdown: get unmanaged devices count: 0 Nov 2 13:50:22 Cobalt bluetoothd[1016]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> modem-manager is now available Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> monitoring kernel firmware directory '/lib/firmware'. Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiFi enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WWAN enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiMAX enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> Networking is enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt kernel: [ 28.688167] type=1400 audit(1351882222.452:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1046 comm="apparmor_parser" Nov 2 13:50:22 Cobalt bluetoothd[1062]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1118]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1237]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) ps aux | grep -i network root 978 0.0 0.1 23732 4808 ? Ssl 13:50 0:00 NetworkManager sudo modprobe -r forcedeth FATAL: Module forcedeth not found

    Read the article

  • Printer server drivers for Samsung ML printer series

    - by drpcken
    I have a Printer Server running server 2008. I'm trying to setup some Samsung ML printers on it (ML-3050, 2150 and 2570 printers). The print server is server 2008 and all my clients are Windows 7 x86. I just never know which drivers to get for the server. On the site they have Universal, PCL5 and PCL6, PostScript, and SPL drivers. From what I've read PS is the best right? I just have problems getting them installed on the server and having clients connect. Which driver type is the best?

    Read the article

  • samsung CLP-310N password recovery

    - by alumb
    I have a Samsung CLP-310N printer and I'm trying to get the Administrator password. Is there a default password? Any way to reset the printer to defaults? Anyone run into this problem before? (I tried Network Settings -- Reset -- Factory Defaults, but that requires a password)

    Read the article

  • How to install a Lexmark z600 series printer?

    - by Uri Herrera
    It has been a headache trying to install this printer. All the tutorials I found are for older versions of Ubuntu, and none of them work. How can I install this printer? Edit: HOWTO: Install PITA Lexmark Z600 Z615 and Dell Photo Printer 720 Setup Lexmark Z600 and X series printer on Ubuntu (i tried this one, only that it was translated to spanish, but it was the same instructions) HOWTO: Lexmark Printers I always get an error when extracting the converted tars with all of the tuts, invalid argument or the file doesn't exist. Looks like, i was missing some ia32 libs .. and that caused the errors with the tar files, anyways i still can't print now i get this, cups-insecure-filter How to install Lezmark Z600 series printer Here, the OP offers 2 debs, i installed them on a 32 bit Ubuntu install, now the printer gets recognized but still can't print, 'cause i'm missing a filter, "rastertoz600".

    Read the article

  • How to install a Lexmark z600 series printer?

    - by Uri Herrera
    It has been a headache trying to install this printer. All the tutorials I found are for older versions of Ubuntu, and none of them work. How can I install this printer? Edit: HOWTO: Install PITA Lexmark Z600 Z615 and Dell Photo Printer 720 Setup Lexmark Z600 and X series printer on Ubuntu (i tried this one, only that it was translated to spanish, but it was the same instructions) HOWTO: Lexmark Printers I always get an error when extracting the converted tars with all of the tuts, invalid argument or the file doesn't exist. Looks like, i was missing some ia32 libs .. and that caused the errors with the tar files, anyways i still can't print now i get this, cups-insecure-filter How to install Lezmark Z600 series printer Here, the OP offers 2 debs, i installed them on a 32 bit Ubuntu install, now the printer gets recognized but still can't print, 'cause i'm missing a filter, "rastertoz600".

    Read the article

  • I can not print on Windows 7 shared printer

    - by lrichard
    For a while I can not print from my Ubuntu 12.04 64 bit pc on a Windows 7 shared printer. Before that everything was ok. The printer is HP LaserJet 1100. The error message is: "File "/usr/lib/cups/backend/smb" not available: No such file or directory" I have tried to reinstall the samba, I have configured the workgroup properly. I have tried to reinstall the printer on the Ubuntu machine with the proper address, or with lpd (I have read somewhere). If I restart the printer on the cups web interface ("Resume Printer") the problem seems to be solved, but not. (The printer seems to be idle, and if I want to print, I still get the error message.) I have checked the share rights on the Windows 7 pc, and I think it is ok.

    Read the article

  • Virtualbox share guest (windows xp) printer to host(linux)

    - by M0E-lnx
    I have a weird situation. I own a printer that has 0 support in linux, but of course, it works in windows. So I have installed VirtualBox 3.1.2 with guest additions to provide access to my usb devices. I have successfully setup the printer and the guest os can print fine. Now, the question is: Is there any way to make this printer accessible to the host OS? I noticed that the guest OS takes an ip address of 10.0.2.15, but when I try to ping that address from the linux host, it goes nowhere. No response. Has anyone here done this before? can anyone think of a way to do this?

    Read the article

  • Is it necessary to add an HP printer to CUPS using the hplip URI?

    - by JPbuntu
    I recently setup a CUPS print server (Ubuntu server 12.04) and I having trouble with performance of a HP Color LaserJet Printer CP3505n. The printer pauses for about a second between printing each page, which is annoying when there is a lot of printing to be done. This doesn't happen when the printer is installed directly to a Windows client. In an attempt to fix this I have setup the printer a couple different ways. I decided not to do a Samba share since this wiki said IPP is preferred. First Method Added to HP LaserJet to CUPS as a Discovered Network Printer, and selected HP Color LaserJet cp3505 hpijs pcl3, 3.12.2 (en) driver. I did not use a hplip URI. Second Method (hplip URI) I thought adding hplip to the mix might improve the performance, so I added the printer like this: Ran hp-setup -m 192.168.2.60, prompted to select driver Selected HP Color LaserJet cp3505 hpijs pcl3, 3.12.2 (en) Used hplip to generate a URI: hp-makeuri 192.168.2.60 Then added the printer to CUPS as a Local Printer: HP Printer (HPLIP), and entered: hp:/net/HP_Color_LaserJet_CP3505?ip=192.168.2.60. Either method I use I am able to share the printer on the network by adding a printer as http://192.168.2.2:631/printers/HP_LASER-TERRAC. Does it make a difference which way the printer is added cups? If so, and I install the printer with the hp URI, can I still change the driver using the CUPS web interface? I have been trying out different drivers to try and improve performance, and the cups interface is the easiest way to change them. Thanks in advance.

    Read the article

  • Application losing Printer within Terminal Services for remote users

    - by Richard
    Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

    Read the article

  • Application losing Printer within Terminal Services for remote users

    - by Richard
    Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

    Read the article

  • Trouble with HP printer

    - by reyjavikvi
    I have a HP Photosmart C3180 (it's a printer/scanner). For some reason, it recently stopped working. The power light is blinking (I think all the other lights are one, but don't remember, I'm not there right now), and the only way to turn it off is to unplug it. It won't print anything, and when you put a page in the tray it sucks it in without printing anything on it and stops when the paper is on its way out (Again, I don't remember how we managed to get it out, sorry). This printer is hooked up to a computer running XP, but it doesn't work either when printing from the network. Weirdly, the scanner works fine. Do you have any ideas on what could be the problem? Could it be a driver problem? By the way, sorry if the question lacks a bit of detail. I don't know much about printers, and I don't have it here so I can't remember exactly all the details. If needed I can update the question tonight or tomorrow.

    Read the article

  • Linux drivers for laser printer Konica Minolta Magicolor 4750DN

    - by user51166
    I would like to install the konica minolta magicolor 4750DN in Linux (debian 64 bits, I know it's not really supported but that's not the issue right now) but all the manual says is "put the CD rom in and copy the drivers and PPD file". However I did not get the CD ! On their "fantastic" internet site (...) there are only available drivers for Windows and Mac OSX. I tried to extract the ppd file from the .dmg file for MacOSX 10.7 but, if the PPD file works, a compiled file (only mac compiled, MACH 4 architectures says the "file" command) does not (obviously "cannot execute binary file", since I'm trying to run a Mac file on Linux). Is there anybody who has the same printer that could lend me the Linux drivers on the CD ROM ? Couldn't find them anywhere on the internet. Any way to execute a Mach (or BSD) binary file on Linux (I don't think is possible, although some "emulators" may exist). Thank you very much. I buyed this printer even because it was advertised as "Linux compatible", only to get this bad surprise. I would be grateful if you could help me solve this problem.

    Read the article

  • Virtual PC network connection setting issue

    - by George2
    Hello everyone, I am using Virtual PC 2007 on Windows Vista Enterprise x86. My confusion is about the network setting for guest OS. In the network setting, I can set the network adaptor of guest OS to one of my physical network adaptors of my host OS (I have tested that it works for guest OS to use the physical network adaptor of host OS to access external network). But in this way, 1. since both host OS and guest OS will use the same physical network adaptor, will there be any conflicts (e.g. same H/W serves two OS)? 2. will guest OS share a part of network bandwidth of the host OS of the physical network adaptor? 3. What means NAT setting in guest OS network connection adaptor? thanks in advance, George

    Read the article

  • How to factory reset an EPSON Stylus Photo 1290 printer?

    - by Harry Wood
    How do I do factory reset on an EPSON Stylus Photo 1290 printer? The printer is refusing to work. It seems to be in some error state. I've tried re-installing drivers etc, but the printer itself seems to run some diagnostic routine when I switch it on, but will not do anything else. It will not move the carousel ready for me to change the printer cartridge or any other Is there'e some sequence of button presses on the printer to do a factory reset? The printer has three buttons on the front, plus a yellow button when the hood is open (as shown in this photo)

    Read the article

  • Building a Mac/PC Network in a Dorm with Network Restrictions

    - by user70340
    I have been a Windows XP user for the last few years, but I recently bought a 15'' MacBook Pro for research purposes. I would like to set up a no-hassle Mac/PC Network at home so that I can access the internet on both computers and hardware between computers (i.e. a harddrive, or a mouse/keyboard with Synergy). Unfortunately, I live in a dorm with silly network restrictions so a solution is not straightforward. In particular: The dorm has a wired and wireless network, both which provide an internet connection. The wired network provides way faster internet (download speeds of 15 MB/s vs. 2 MB/s on wireless), so I would like to somehow exploit this, at least on my PC for Bittorrent :) Multiple devices can connect to the wireless network, but cannot "see" each other on the network (so software like Synergy would not work). Only 1 MAC address can connect to the wired network at a time. Ideally I would just connect a wireless router to the wired network and then have both the Mac and the PC on that, but the 1 MAC address restriction will not allow the both computer to access the internet simultaneously. I cannot think of a way to bypass this restriction (though I'm not network savvy), so I am planning to create a private no-internet network to allow the devices to see each other and share hardware. Here are some thoughts. I would appreciate any feedback at all! If I build a private wireless network: (first choice) I will use a wireless router that is not connected to the internet. My PC and Mac will be connected to each other wirelessly. I can then connect the PC to the internet via a wired network, but then the Mac will not have internet access as its wireless card is already in use. In this case, could I stream internet access from the PC to the Mac via the wireless network? Or could I buy a USB wireless card for the Mac so that it can connect to both my private network and the dorm network? If I build a private wired network: (second choice) Then both the PC and the Mac will connect to the internet wirelessly, which means I cannot take advantage of the faster download speeds.

    Read the article

  • Use Network-Manager to Connect to a wifi Access Point on the command-line

    - by Stefano Palazzo
    I'd like to connect to a wireless access point from the command-line. ideally, I'd only need the name of the AP. But the hardware-address would work as well. I know I can use nmcli to connect to a managed network connection, but in my case, the access point may not be configured for Network-Manager yet (See the difference between the output of nm-tool and nmcli con). Example output of nmcli: Auto pwln 3a3d62b1-bbdf-4f76-b4d2-c211fd5cfb03 802-11-wireless [...] Wired Network aa586921-accf-4932-98c4-c873c310f08e 802-3-ethernet [...] Cisco-UDP Uni 7f94847b-04dc-40b7-9955-5246fb77cc65 vpn [...] T-mobile (D1) 867f345a-cbbf-4bd4-b883-a5e5ae0932f0 gsm [...] Example output of nm-tool: State: connected - Device: eth1 [Auto pwln] ---------------------------------------------------- [...] Wireless Access Points (* = current AP) *pwln: Infra, [...], Freq 2472 MHz, Rate 54 Mb/s, Strength 80 WPA WPA2 WLAN: Infra, [...], Freq 2422 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 [...] How do I connect to an access point that may or may not be known to NM? Extra: Finding out if the connection needs a pass-phrase, and submitting it on the command-line as well would be great too (that is to say It'd be nice if network-manager wouldn't pop open any keyring dialogues or errors on the gui)

    Read the article

  • Can't connect to hidden network with BCM4313

    - by poomerang
    The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

    Read the article

  • "Enable Wireless" option is disabled in network settings

    - by silenTK
    I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

    Read the article

  • Ubuntu 12.04 on Vm Player showing Wired Network Instead of Wireless Network

    - by Fak365
    I am new to Ubuntu, recently I installed ubuntu 12.04 in Vm Player (Virtual Machine) on my Dell laptop having windows 7 ultimate 32 bit for just to check the security of my wireless network and want to crack the WiFi (WPA-PSK) password but in ubuntu it does not show the wireless network it shows the 2 arrow sign as i have not connect the ethernet cable to my laptop and connected through WiFi on my main OS (windows 7) but it shows the wired network and internet is working but it does not show wifi connection. On windows 7 WiFi is connected and showing the WiFi connection and working correctly.But my main motive is to crack the WiFi password as it can't detect WiFi network so what to do? Please Help.!!thanks My Laptop Specification : Laptop : Dell Latitude D620 OS : Windows 7 Ultimate 32 bit Processor : Core Duo 2 T7200 @ 2Ghz Ram : 2 GB WiFi card : Intel Pro/Wireless 3945 ABG Virtual Machine : Vm Player V 5.0.1 If Need to Install Drivers Please Give Me Full Information how to install and which driver I should install. Thanks In Advance.

    Read the article

  • Print raw data to a thermal-printer using c#

    - by blauesocke
    Hi, I'm trying to print out raw ascii data to a thermal printer. I do this by using this code example: http://support.microsoft.com/kb/322091 but my printer prints always only one character and this not until I press the form feed button. If I print something with notepad the printer will do a form feed automatically but without printing any text. The printer is connected via usb over a lpt2usb adapter and Windows 7 uses the "Generic - Generic / Text Only" driver. Anyone knows what is going wrong? How is it possible to print some words and do some form feeds? Are there some control characters I have to send? And if yes: How do I send them? Thanks!

    Read the article

  • Cannot turn on "Network Discovery and File Sharing" when Windows Firewall is enabled

    - by Cheeso
    I have a problem similar to this one. Windows Firewall prevents File and Printer sharing from working and Why does File and Printer Sharing keep turning off in Windows 7? I cannot turn on Network Discovery. This is Windows 7 Home Premium, x64. It's a Dell XPS 1340 and Windows came installed from the OEM. This used to work. Now it doesn't. I don't know what has changed. In windows Explorer, the UI looks like this: When I click the yellow panel that says "Click to change...", the panel disappears, then immediately reappears, with exactly the same text. If I go through the control panel "Network and Sharing Center" thing, the UI looks like this: If I tick the box to "turn on network discovery", the "Save Changes" button becomes enabled. If I then click that button, the dialog box just closes, with no message or confirmation. Re-opening the same dialog box shows that Network Discovery has not been turned on. If I turn off Windows Firewall, I can then turn on Network Discovery via either method. The machine is connected to a wireless home network, via a router. The network is marked as "Home Network" in the Network and Sharing Center, which I think corresponds to the "Private" profile in Windows Firewall Advanced Settings app. (Confirm?) The PC is not part of a domain, and has never been part of a domain. The machine is not bridging any networks. There is a regular 100baseT connector but I have the network adapter for that disabled in Windows. Something else that seems odd. Within Windows Firewall Advanced Settings, there are no predefined rules available. If I click the "New Rule...." Action on the action pane, the "Predefined" option is greyed out. like this: In order to attempt to allow the network discovery protocols through on the private network, I hand-coded a bunch of rules, intending to allow the necessary UPnP and WDP protocols supporting network discovery. I copied them from a working Windows 7 Ultimate PC, running on the same network. This did not work. Even with the hand-coded rules, I still cannot turn on Network Discovery. I looked on the interwebs, and the only solution that appears to work is a re-install of Windows. Seriously? If I try netsh advfirewall firewall set rule group="Network Discovery" new enable=Yes ...it says "No rules match the specified criteria" EDIT: by the way, these services are running. DNS Client Function Discovery Resource Publication SSDP Discovery UPnP Device Host in any case, since it works with no firewall, I would assume all necessary services are present and running. The issue is a firewall thing, but I don't know how to diagnose further, or fix it. Q1: Is there a way to definitively insure the correct holes are punched through the Windows Firewall to allow Network Discovery to function? Q2: Should I expect the "predefined" firewall rules to be greyed out? Q3: Why did this change?

    Read the article

  • Generic Text Only printer driver mangles control codes

    - by Terry
    If an escape character (or most other characters < 0x20) is sent to the generic / text only printer it gets printed as a period. Using the code in the WinDDK is it possible to 'correct' this behaviour so that it passes it through unmodified? The general scenario for this is that some application ('user app') outputs a document to a windows printer. My application requires this data in plain text form and so what I do is run a generic / text only printer that talks to a virtual com port. This generally works fine except where the 'user app' outputs binary data to the print queue without using the correct mechanism (which seems to work fine on some printer drivers, such as the Epson POS ones, but not the generic / text only one). I've tried changing the print processor selection without success and also tried looking at the gtt files to see if I could readily map in these characters as though they were printable, but the minidriver tool won't let me do that. Any suggestions?

    Read the article

  • How to resume CUPS printer from command line

    - by stach81
    Hello I have printer in CUPS that due driver problems (hp 1010) form time to time goes into pause. I would like to write a shell script that will be once per hour resuming printer in cups. But I have no idea after googling for couple of minutes how to resume printer from shell command line. Regards Stan

    Read the article

  • Writing a Virtual Printer in .NET

    - by David Osborn
    I'm looking to create a virtual printer that passes data to my .NET application. I want to then create an installer that installs both the printer and the .NET application. It would we really nice to be able to write it all in C#, but I have a feeling that this will require a printer driver to be written is unmanaged code. Does anyone know of a fairly clean tutorial or example of how to do this?

    Read the article

  • Printer Page Size Problem

    - by mRt
    I am trying to set a custom paper size by doing: Printer.Height = 2160 Printer.Width = 11900 But it doesn't seen to have any effect. After setting this up, i ask for that values and it returns the default ones. And this: Printer.PaperSize = 256 Returns an error... Any ideas??

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >