Search Results

Search found 232 results on 10 pages for 'recurring'.

Page 10/10 | < Previous Page | 6 7 8 9 10 

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Cisco 800 series won't forward port

  - by sam

  Hello ServerFault, I am trying to forward port 444 from my cisco router to my Web Server (192.168.0.2). As far as I can tell, my port forwarding is configured correctly, yet no traffic will pass through on port 444. Here is my config: ! version 12.3 service config no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug uptime service timestamps log uptime service password-encryption no service dhcp ! hostname QUESTMOUNT ! logging buffered 16386 informational logging rate-limit 100 except warnings no logging console no logging monitor enable secret 5 -removed- ! username administrator secret 5 -removed- username manager secret 5 -removed- clock timezone NZST 12 clock summer-time NZDT recurring 1 Sun Oct 2:00 3 Sun Mar 3:00 aaa new-model ! ! aaa authentication login default local aaa authentication login userlist local aaa authentication ppp default local aaa authorization network grouplist local aaa session-id common ip subnet-zero no ip source-route no ip domain lookup ip domain name quest.local ! ! no ip bootp server ip inspect name firewall tcp ip inspect name firewall udp ip inspect name firewall cuseeme ip inspect name firewall h323 ip inspect name firewall rcmd ip inspect name firewall realaudio ip inspect name firewall streamworks ip inspect name firewall vdolive ip inspect name firewall sqlnet ip inspect name firewall tftp ip inspect name firewall ftp ip inspect name firewall icmp ip inspect name firewall sip ip inspect name firewall fragment maximum 256 timeout 1 ip inspect name firewall netshow ip inspect name firewall rtsp ip inspect name firewall skinny ip inspect name firewall http ip audit notify log ip audit po max-events 100 ip audit name intrusion info list 3 action alarm ip audit name intrusion attack list 3 action alarm drop reset no ftp-server write-enable ! ! ! ! crypto isakmp policy 1 authentication pre-share ! crypto isakmp policy 2 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group staff key 0 qS;,sc:q<skro1^, domain quest.local pool vpnclients acl 106 ! ! crypto ipsec transform-set tr-null-sha esp-null esp-sha-hmac crypto ipsec transform-set tr-des-md5 esp-des esp-md5-hmac crypto ipsec transform-set tr-des-sha esp-des esp-sha-hmac crypto ipsec transform-set tr-3des-sha esp-3des esp-sha-hmac ! crypto dynamic-map vpnusers 1 description Client to Site VPN Users set transform-set tr-des-md5 ! ! crypto map cm-cryptomap client authentication list userlist crypto map cm-cryptomap isakmp authorization list grouplist crypto map cm-cryptomap client configuration address respond crypto map cm-cryptomap 65000 ipsec-isakmp dynamic vpnusers ! ! ! ! interface Ethernet0 ip address 192.168.0.254 255.255.255.0 ip access-group 102 in ip nat inside hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! interface Dialer0 bandwidth 640 ip address negotiated ip access-group 101 in no ip redirects no ip unreachables ip nat outside ip inspect firewall out ip audit intrusion in encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username -removed- password 7 -removed- ppp ipcp dns request crypto map cm-cryptomap ! ip local pool vpnclients 192.168.99.1 192.168.99.254 ip nat inside source list 105 interface Dialer0 overload ip nat inside source static tcp 192.168.0.2 444 interface Dialer0 444 ip nat inside source static tcp 192.168.0.51 9000 interface Dialer0 9000 ip nat inside source static udp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 25 interface Dialer0 25 ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ip http server no ip http secure-server ! ip access-list logging interval 10 logging 192.168.0.2 access-list 1 remark The local LAN. access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.0.0 access-list 2 remark Where management can be done from. access-list 2 permit 192.168.0.0 0.0.0.255 access-list 3 remark Traffic not to check for intrustion detection. access-list 3 deny 192.168.99.0 0.0.0.255 access-list 3 permit any access-list 101 remark Traffic allowed to enter the router from the Internet access-list 101 permit ip 192.168.99.0 0.0.0.255 192.168.0.0 0.0.0.255 access-list 101 deny ip 0.0.0.0 0.255.255.255 any access-list 101 deny ip 10.0.0.0 0.255.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 169.254.0.0 0.0.255.255 any access-list 101 deny ip 172.16.0.0 0.15.255.255 any access-list 101 deny ip 192.0.2.0 0.0.0.255 any access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 198.18.0.0 0.1.255.255 any access-list 101 deny ip 224.0.0.0 0.15.255.255 any access-list 101 deny ip any host 255.255.255.255 access-list 101 permit tcp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit tcp host 120.136.2.22 any eq 1433 access-list 101 permit tcp host 123.100.90.58 any eq 1433 access-list 101 permit udp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit udp host 120.136.2.22 any eq 1433 access-list 101 permit udp host 123.100.90.58 any eq 1433 access-list 101 permit tcp any any eq 444 access-list 101 permit tcp any any eq 9000 access-list 101 permit tcp any any eq smtp access-list 101 permit udp any any eq non500-isakmp access-list 101 permit udp any any eq isakmp access-list 101 permit esp any any access-list 101 permit tcp any any eq 1723 access-list 101 permit gre any any access-list 101 permit tcp any any eq 22 access-list 101 permit tcp any any eq telnet access-list 102 remark Traffic allowed to enter the router from the Ethernet access-list 102 permit ip any host 192.168.0.254 access-list 102 deny ip any host 192.168.0.255 access-list 102 deny udp any any eq tftp log access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 102 deny ip any 0.0.0.0 0.255.255.255 log access-list 102 deny ip any 10.0.0.0 0.255.255.255 log access-list 102 deny ip any 127.0.0.0 0.255.255.255 log access-list 102 deny ip any 169.254.0.0 0.0.255.255 log access-list 102 deny ip any 172.16.0.0 0.15.255.255 log access-list 102 deny ip any 192.0.2.0 0.0.0.255 log access-list 102 deny ip any 192.168.0.0 0.0.255.255 log access-list 102 deny ip any 198.18.0.0 0.1.255.255 log access-list 102 deny udp any any eq 135 log access-list 102 deny tcp any any eq 135 log access-list 102 deny udp any any eq netbios-ns log access-list 102 deny udp any any eq netbios-dgm log access-list 102 deny tcp any any eq 445 log access-list 102 permit ip 192.168.0.0 0.0.0.255 any access-list 102 permit ip any host 255.255.255.255 access-list 102 deny ip any any log access-list 105 remark Traffic to NAT access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 106 remark User to Site VPN Clients access-list 106 permit ip 192.168.0.0 0.0.0.255 any dialer-list 1 protocol ip permit ! line con 0 no modem enable line aux 0 line vty 0 4 access-class 2 in transport input telnet ssh transport output none ! scheduler max-task-time 5000 ! end any ideas? :)

  Read the article

• Cisco ASA: Allowing and Denying VPN Access based on membership to an AD group

  - by milkandtang

  I have a Cisco ASA 5505 connecting to an Active Directory server for VPN authentication. Usually we'd restrict this to a particular OU, but in this case users which need access are spread across multiple OUs. So, I'd like to use a group to specify which users have remote access. I've created the group and added the users, but I'm having trouble figuring out how to deny users which aren't in that group. Right now, if someone connects they get assigned the correct group policy "companynamera" if they are in that group, so the LDAP mapping is working. However, users who are not in that group still authenticate fine, and their group policy becomes the LDAP path of their first group, i.e. CN=Domain Users,CN=Users,DC=example,DC=com, and then are still allowed access. How do I add a filter so that I can map everything that isn't "companynamera" to no access? Config I'm using (with some stuff such as ACLs and mappings removed, since they are just noise here): gateway# show run : Saved : ASA Version 8.2(1) ! hostname gateway domain-name corp.company-name.com enable password gDZcqZ.aUC9ML0jK encrypted passwd gDZcqZ.aUC9ML0jK encrypted names name 192.168.0.2 dc5 description FTP Server name 192.168.0.5 dc2 description Everything server name 192.168.0.6 dc4 description File Server name 192.168.0.7 ts1 description Light Use Terminal Server name 192.168.0.8 ts2 description Heavy Use Terminal Server name 4.4.4.82 primary-frontier name 5.5.5.26 primary-eschelon name 172.21.18.5 dmz1 description Kerio Mail Server and FTP Server name 4.4.4.84 ts-frontier name 4.4.4.85 vpn-frontier name 5.5.5.28 ts-eschelon name 5.5.5.29 vpn-eschelon name 5.5.5.27 email-eschelon name 4.4.4.83 guest-frontier name 4.4.4.86 email-frontier dns-guard ! interface Vlan1 nameif inside security-level 100 ip address 192.168.0.254 255.255.255.0 ! interface Vlan2 description Frontier FiOS nameif outside security-level 0 ip address primary-frontier 255.255.255.0 ! interface Vlan3 description Eschelon T1 nameif backup security-level 0 ip address primary-eschelon 255.255.255.248 ! interface Vlan4 nameif dmz security-level 50 ip address 172.21.18.254 255.255.255.0 ! interface Vlan5 nameif guest security-level 25 ip address 172.21.19.254 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport access vlan 3 ! interface Ethernet0/2 switchport access vlan 4 ! interface Ethernet0/3 switchport access vlan 5 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS name-server dc2 domain-name corp.company-name.com same-security-traffic permit intra-interface access-list companyname_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0 access-list companyname_splitTunnelAcl standard permit 172.21.18.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.20.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.18.0 255.255.255.0 access-list bypassingnat_dmz extended permit ip 172.21.18.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 12288 logging buffered warnings logging asdm notifications mtu inside 1500 mtu outside 1500 mtu backup 1500 mtu dmz 1500 mtu guest 1500 ip local pool VPNpool 172.21.20.50-172.21.20.59 mask 255.255.255.0 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 email-frontier global (outside) 3 guest-frontier global (backup) 1 interface global (dmz) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 dc5 255.255.255.255 nat (inside) 1 192.168.0.0 255.255.255.0 nat (dmz) 0 access-list bypassingnat_dmz nat (dmz) 2 dmz1 255.255.255.255 nat (dmz) 1 172.21.18.0 255.255.255.0 access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 4.4.4.1 1 track 1 route backup 0.0.0.0 0.0.0.0 5.5.5.25 254 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 ldap attribute-map RemoteAccessMap map-name memberOf IETF-Radius-Class map-value memberOf CN=RemoteAccess,CN=Users,DC=corp,DC=company-name,DC=com companynamera dynamic-access-policy-record DfltAccessPolicy aaa-server ActiveDirectory protocol ldap aaa-server ActiveDirectory (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft aaa-server ADRemoteAccess protocol ldap aaa-server ADRemoteAccess (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft ldap-attribute-map RemoteAccessMap aaa authentication enable console LOCAL aaa authentication ssh console LOCAL http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sla monitor 123 type echo protocol ipIcmpEcho 4.4.4.1 interface outside num-packets 3 frequency 10 sla monitor schedule 123 life forever start-time now crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 ! track 1 rtr 123 reachability telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 management-access inside dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy companynamera internal group-policy companynamera attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com group-policy companyname internal group-policy companyname attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com username admin password IhpSqtN210ZsNaH. encrypted privilege 15 tunnel-group companyname type remote-access tunnel-group companyname general-attributes address-pool VPNpool authentication-server-group ActiveDirectory LOCAL default-group-policy companyname tunnel-group companyname ipsec-attributes pre-shared-key * tunnel-group companynamera type remote-access tunnel-group companynamera general-attributes address-pool VPNpool authentication-server-group ADRemoteAccess LOCAL default-group-policy companynamera tunnel-group companynamera ipsec-attributes pre-shared-key * ! class-map type inspect ftp match-all ftp-inspection-map class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect ftp ftp-inspection-map parameters class ftp-inspection-map policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns migrated_dns_map_1 inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect ils inspect netbios inspect rsh inspect rtsp inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp inspect icmp inspect icmp error inspect esmtp inspect pptp ! service-policy global_policy global prompt hostname context Cryptochecksum:487525494a81c8176046fec475d17efe : end gateway# Thanks so much!

  Read the article

• Trying to configure HWIC-3G-HSPA

  - by user1174838

  I'm trying to configure a couple of Cisco 1941 routes. The are both identical routers. Each as a HWIC-1T (Smart Serial interface) and a HWIC-3G-HSPA 3G interface. These routers are to be sent to remote sites. We have connectivity to one of the sites but if remote site A gors down we lose connectivity to remote site B. The HWIC-1T is the primary WAN interface using frame relay joining the two remote sites We want the HWIC-3G-HSPA to be usable for direct connectivity from head office to remote site B, and also the HWIC-3G-HSPA is do be used for comms between the remote sites when the frame relay is down (happens quite a bit). I initialy tried to do dynamic routing using EIGRP however in my lab setup of laptop - 1941 - 1941 - laptop, I was unable to get end to end connectivity. I later settled on static routing and have got end to end connectivity but only over frame relay, not the HWIC-3G-HSPA. The sanitized running config for remote site A: version 15.1 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service udp-small-servers service tcp-small-servers ! hostname remoteA ! boot-start-marker boot-end-marker ! ! logging buffered 51200 warnings enable secret 5 censored ! no aaa new-model clock timezone wst 8 0 ! no ipv6 cef ip source-route ip cef ! ip domain name yourdomain.com multilink bundle-name authenticated ! chat-script gsm "" "ATDT*98*1#" TIMEOUT 30 "CONNECT" ! username admin privilege 15 secret 5 censored ! controller Cellular 0/1 ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.2.5 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 ip address 10.1.1.2 255.255.255.252 encapsulation frame-relay cdp enable frame-relay interface-dlci 16 frame-relay lmi-type ansi ! interface Cellular0/1/0 ip address negotiated encapsulation ppp dialer in-band dialer idle-timeout 2147483 dialer string gsm dialer-group 1 async mode interactive ppp chap hostname censored ppp chap password 7 censored cdp enable ! interface Cellular0/1/1 no ip address encapsulation ppp ! interface Dialer0 no ip address ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Serial0/0/0 210 permanent ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 220 permanent ip route 172.31.2.0 255.255.255.0 Cellular0/1/0 permanent ip route 192.168.3.0 255.255.255.0 10.1.1.1 permanent ip route 192.168.3.0 255.255.255.0 Cellular0/1/0 210 permanent ! access-list 1 permit any dialer-list 1 protocol ip list 1 ! control-plane ! line con 0 logging synchronous login local line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line 0/1/0 exec-timeout 0 0 script dialer gsm login modem InOut no exec transport input all rxspeed 7200000 txspeed 5760000 line 0/1/1 no exec rxspeed 7200000 txspeed 5760000 line vty 0 4 access-class 23 in privilege level 15 password 7 censored login local transport input all line vty 5 15 access-class 23 in privilege level 15 password 7 censored login local transport input all line vty 16 1370 password 7 censored login transport input all ! scheduler allocate 20000 1000 end The sanitized running config for remote site B: version 15.1 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service udp-small-servers service tcp-small-servers ! hostname remoteB ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings enable secret 5 censored ! no aaa new-model clock timezone wst 8 0 ! no ipv6 cef ip source-route ip cef ! no ip domain lookup ip domain name yourdomain.com multilink bundle-name authenticated ! chat-script gsm "" "ATDT*98*1#" TIMEOUT 30 "CONNECT" username admin privilege 15 secret 5 censored ! controller Cellular 0/1 ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.3.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 ip address 10.1.1.1 255.255.255.252 encapsulation frame-relay clock rate 2000000 cdp enable frame-relay interface-dlci 16 frame-relay lmi-type ansi frame-relay intf-type dce ! interface Cellular0/1/0 ip address negotiated encapsulation ppp dialer in-band dialer idle-timeout 2147483 dialer string gsm dialer-group 1 async mode interactive ppp chap hostname censored ppp chap password 7 censored ppp ipcp dns request cdp enable ! interface Cellular0/1/1 no ip address encapsulation ppp ! interface Dialer0 no ip address ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Serial0/0/0 210 permanent ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 220 permanent ip route 172.31.2.0 255.255.255.0 Cellular0/1/0 permanent ip route 192.168.2.0 255.255.255.0 10.1.1.2 permanent ip route 192.168.2.0 255.255.255.0 Cellular0/1/0 210 permanent ! kron occurrence PING in 1 recurring policy-list ICMP ! access-list 1 permit any dialer-list 1 protocol ip list 1 ! control-plane ! line con 0 logging synchronous login local line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line 0/1/0 exec-timeout 0 0 script dialer gsm login modem InOut no exec transport input all rxspeed 7200000 txspeed 5760000 line 0/1/1 no exec rxspeed 7200000 txspeed 5760000 line vty 0 4 access-class 23 in privilege level 15 password 7 censored login transport input all line vty 5 15 access-class 23 in privilege level 15 password 7 censored login transport input all line vty 16 1370 password 7 censored login transport input all ! scheduler allocate 20000 1000 end The last problem I'm having is the 3G interfaces go down after only a few minutes of inactivity. I've tried using kron to ping the local HWIC-3G-HSPA interface (cellular 0/1/0) every minute but that hasn't been successful. Manually pinging the IP assigned (by the telco) to ce0/1/0 does bring the interface up. Any ideas? Thanks

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Class member functions instantiated by traits [policies, actually]

  - by Jive Dadson

  I am reluctant to say I can't figure this out, but I can't figure this out. I've googled and searched Stack Overflow, and come up empty. The abstract, and possibly overly vague form of the question is, how can I use the traits-pattern to instantiate member functions? [Update: I used the wrong term here. It should be "policies" rather than "traits." Traits describe existing classes. Policies prescribe synthetic classes.] The question came up while modernizing a set of multivariate function optimizers that I wrote more than 10 years ago. The optimizers all operate by selecting a straight-line path through the parameter space away from the current best point (the "update"), then finding a better point on that line (the "line search"), then testing for the "done" condition, and if not done, iterating. There are different methods for doing the update, the line-search, and conceivably for the done test, and other things. Mix and match. Different update formulae require different state-variable data. For example, the LMQN update requires a vector, and the BFGS update requires a matrix. If evaluating gradients is cheap, the line-search should do so. If not, it should use function evaluations only. Some methods require more accurate line-searches than others. Those are just some examples. The original version instantiates several of the combinations by means of virtual functions. Some traits are selected by setting mode bits that are tested at runtime. Yuck. It would be trivial to define the traits with #define's and the member functions with #ifdef's and macros. But that's so twenty years ago. It bugs me that I cannot figure out a whiz-bang modern way. If there were only one trait that varied, I could use the curiously recurring template pattern. But I see no way to extend that to arbitrary combinations of traits. I tried doing it using boost::enable_if, etc.. The specialized state information was easy. I managed to get the functions done, but only by resorting to non-friend external functions that have the this-pointer as a parameter. I never even figured out how to make the functions friends, much less member functions. The compiler (VC++ 2008) always complained that things didn't match. I would yell, "SFINAE, you moron!" but the moron is probably me. Perhaps tag-dispatch is the key. I haven't gotten very deeply into that. Surely it's possible, right? If so, what is best practice? UPDATE: Here's another try at explaining it. I want the user to be able to fill out an order (manifest) for a custom optimizer, something like ordering off of a Chinese menu - one from column A, one from column B, etc.. Waiter, from column A (updaters), I'll have the BFGS update with Cholesky-decompositon sauce. From column B (line-searchers), I'll have the cubic interpolation line-search with an eta of 0.4 and a rho of 1e-4, please. Etc... UPDATE: Okay, okay. Here's the playing-around that I've done. I offer it reluctantly, because I suspect it's a completely wrong-headed approach. It runs okay under vc++ 2008. #include <boost/utility.hpp> #include <boost/type_traits/integral_constant.hpp> namespace dj { struct CBFGS { void bar() {printf("CBFGS::bar %d\n", data);} CBFGS(): data(1234){} int data; }; template<class T> struct is_CBFGS: boost::false_type{}; template<> struct is_CBFGS<CBFGS>: boost::true_type{}; struct LMQN {LMQN(): data(54.321){} void bar() {printf("LMQN::bar %lf\n", data);} double data; }; template<class T> struct is_LMQN: boost::false_type{}; template<> struct is_LMQN<LMQN> : boost::true_type{}; // "Order form" struct default_optimizer_traits { typedef CBFGS update_type; // Selection from column A - updaters }; template<class traits> class Optimizer; template<class traits> void foo(typename boost::enable_if<is_LMQN<typename traits::update_type>, Optimizer<traits> >::type& self) { printf(" LMQN %lf\n", self.data); } template<class traits> void foo(typename boost::enable_if<is_CBFGS<typename traits::update_type>, Optimizer<traits> >::type& self) { printf("CBFGS %d\n", self.data); } template<class traits = default_optimizer_traits> class Optimizer{ friend typename traits::update_type; //friend void dj::foo<traits>(typename Optimizer<traits> & self); // How? public: //void foo(void); // How??? void foo() { dj::foo<traits>(*this); } void bar() { data.bar(); } //protected: // How? typedef typename traits::update_type update_type; update_type data; }; } // namespace dj int main() { dj::Optimizer<> opt; opt.foo(); opt.bar(); std::getchar(); return 0; }

  Read the article

< Previous Page | 6 7 8 9 10