Search Results

Search found 12333 results on 494 pages for 'memory leaks'.

Page 102/494 | < Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

• What is Peformance Monitor telling me when my page faults / second are high?

  - by David Robison

  I have a Windows 7 x64 computer that is having performance issues. After some investigation, I have discovered that the page faults / second on it, as reported by Performance Monitor, are really high. Everything else seems to be normal. Resource Monitor reports no hard faults and lots of available memory. Is this a potential cause for problems, or is it a red herring? If it is something that could be causing problems, what should I do next to figure out what is causing it? Here is a screen shot of the Performance Monitor. Notice that the average page faults / second is 75,887. On another computer that does not have problems, this number is closer to 3,000. Here is a screen shot of the Resource Monitor, sorted by hard faults / second, which is currently 0 for all processes.

  Read the article

• Only some motherboards can support faster RAM?

  - by Wesley

  This is a question relating to one of my builds. Here are the specs: ECS P4VXASD2+ V5.0 motherboard Intel P4 Northwood 2.8 GHz (533 MHz FSB, 512 KB L2) 2x 1GB PC3200 DDR RAM Maxtor 300GB IDE HDD 16 MB NVIDIA TNT2 Pro AGP OKIA 300W ATX PSU Gigabyte 52x CD-ROM The issue right now is that I'm trying to install Windows XP from the CD drive but the computer randomly restarts partway through installation. My other build was BSODing due to RAM latency errors. This ECS board manual states that memory modules "up to 333 MHz" (i.e. PC2700) is supported. However, I am running PC3200 modules, which is clearly faster than PC2700. Would this be causing the computer from randomly restarting? EDIT 1: I also wanted to mention that my Emachines T2482 is actually running 2x 512MB PC3200 DDR RAM when it should only be supporting PC1600 and PC2100 DDR RAM. Yet there are no issues with it.

  Read the article

• Hypertransport sync flood error

  - by Carl B

  What is it? And what causes it? Is it only for uncorrectable DIMM Errors(Troubleshooting DIMM errors)? When an UCE occurs, the memory controller causes an immediate reboot of the system. During reboot, the BIOS checks the Machine Check registers and determines that the previous reboot was due to an UCE, then reports this in POST after the memtest stage: A Hypertransport Sync Flood occurred on last boot 3 BIOS reports this event in the service processor’s system event log (SEL) as shown in the sample IPMItool output There are what seems to be some suggested answers to include Bad Caps Bios verisons (happens in one version not the other) Graphics card issues Lack of power to the CPU The list of possible generators seems to target everything but the computer case. System Specs: Windows Home Premium 64 Motherboard - MSI790FX-GD70 (MS7577) / Bios v 1.9 (American Megatrensa Inc) Ram - Patriot G Series ‘Sector 5’ Edition 4GB DDR3 1600 CPU - AMD Phenom II X2 555 Black Edition Callisto 3.2GHz Socket AM3 80W (Note: unlocked 2 cores CPU Z ids it as phenom II x4 B55) Graphics - 2 x Radeon 5750 in crossfire PSU - ABS 900w HDDs - 2 Seagate 1.5 TB Sata SSD - 1 OCZ 120 GB Vertex Plus R2

  Read the article

• Memeory Leak in Windows Page file when calling a shell command

  - by Arno

  I have an issue on our Windows 2003 x64 Build Server when invoking shell commands from a script. Each call causes a "memory leak" in the page file so it grows quite rapidly until it reaches the maximum and the machine stops working. I can reproduce the problem very nicely by running a perl script like for ($count=1; $count<5000; $count++) { system "echo huhu"; } It is independent of he scripting language as the same happens with lua: for i=1,5000 do os.execute("echo huhu") end I found somebody describing the same issue with php at http://www.issociate.de/board/post/454835/Memory_leak_occurs_when_exec%28%29_function_is_used_on_Windows_platform.html His solution: Firewall/Virus Scanner does not apply, neither are running on the machine. We can also reproduce the issue on other Developer Machines running XP 64, but not on XP 32 Bit. The guilty guy for the allocation is C:\WINDOWS\System32\svchost.exe -k netsvcs which runs all the basic Windows services. Does anybody know the issue and how to resolve it ?

  Read the article

• Why is my Asus P5PL2-E using 640MB of RAM (out of 4GB) ? [closed]

  - by Tom

  Possible Duplicate: Windows XP and RAM 3.5GB+ I've recently installed 4GB of RAM on my server, which is running Windows XP SP2 32-bit and My Computer showed that only 3.37GB were installed. After digging Google for a bit, I couldn't find anything helpful, but I do remember reading a post in a forum regarding the motherboard using 640MB of RAM. Digging in my own BIOS, I've also found that my motherboard has also reserved that amount for its self. Why does my motherboard reserve this memory and how can I tune it down to say 128MB?

  Read the article

• Tuning OpenVZ Containers to work better with Java?

  - by Daniel

  I have a 8 GB RAM Server (Dedicated) and currently have KVM Virtual Machines running on there (successfully) however i'm considering moving to OpenVZ as KVM seems a bit overkill with a lot of overhead for what i use it for. In the past i have used OpenVZ Containers, hosted by myself and from other providers and Java doesn't seem to work well with them.. One example is that if i give a container 2 GB RAM ( No burst) (with or without vswap doesn't matter) a java instance can only be tuned to use at very most 1500 MB of that RAM (-Xmx, -Xms). Ideally, i wish to be able to create "Mini" containers with about 256MB, 512MB, 768 RAM and run some java instances in them. My question is: I'm trying to find an ideal way to tune a OpenVZ container configuration to work better with Java memory. Please, don't suggest anything related to Java settings, i'm looking for OpenVZ specific answers.. Though i welcome any suggestion if you feel it may help me. Much Appreciated, Daniel

  Read the article

• Making the most of dual channel DDR2: how do I arrange the sticks?

  - by andrz_001

  I've searched online, but I can't find anything definitive that will put me at ease. I turn to superuser. This is how I have the RAM sticks arranged now: To make the most of the RAM and the dual channel capability, it occurred to me that perhaps I have the sticks arranged incorrectly. Should I move the stick in the DDR2_2 slot one over--to the adjacent, red slot? I appreciate any suggestions. (BTW, can something in BIOS tell me whether I'm running at "optimal" memory speeds??) edit: I'm running Windows XP SP3, 32-bit. Thanks.

  Read the article

• PC with 2 RAMs of different frequencies (1GB 533MHz + 2GB 667MHz) showing only 2GB RAM

  - by srinivas

  I have 6 years old PC with 1.25GB (1GB + 256MB) of DDR2 533MHz RAM. As computer has become very slow and memory usage reaching its limits most of the times, i decided to upgrade RAM. But unfortunately, im not finding retailers selling DDR2 533Mhz RAM near my area. Since I was not sure mixing up RAMs of different frequencies, i searched in web. Most results said they can be mixed but computer would run at lower frequency of the 2 RAMs. So I bought 2GB DDR2 667Mhz RAM expecting my pc to have 3GB RAM running at 533 MHz. But computer properties page shows only 2GB RAM. BIOS settings too show the slot with 2GB 667MHz as ACTIVE and other slot with 1GB 533MHz as "NOT INSTALLED". When I removed 2GB RAM, they computer shows only 1GB RAM. So for some reason, 1GB RAM is not getting detected/used. What is the problem here? thanks in advance.

  Read the article

• Apache freezing, How to detect which virtual host is getting hit?

  - by mr-euro

  I have a production server that in the last 24 hours has been hard rebooted 4 times due to freezes. Ping is fine but all other services time-out (Apache, SSHd, etc). I have now diagnosed it to Apache running out of memory due to an exorbitant amount of child processes forking suddenly within seconds of starting Apache. Stopping Apache just after rebooting keeps the server stable again. My two questions are: Is there a way to detect which of the vhosts is being suddenly hammered without looking into each vhost's access log one by one? Is there a way to quickly enable/disable vhosts without commenting (#) them all out in httpd.conf?

  Read the article

• What are the best possible ways to benchmark RAM (no-ECC) under linux / arm?

  - by moul

  I want to test integrity and global performances of no-ECC memory chips on a custom board Are there some tools that run under linux so I can monitor system and global temperature in the same time ? Are there some no-ECC specific tests to do in general ? EDIT 1: I already know how to monitor temperature (I use a special platform feature /sys/devices/platform/......../temp1_input). For now : wazoox : it works but I've to code my own tests Jason Huntley : ramspeed : does not work on arm stream benchmark : it works and is very fast, so I'll look if it's accurate and complete memtest : I'll try later, since it does not run directly from linux stress for fedora : I'll try later too, it's too problematic for me to install fedora now I found this distribution : http://www.stresslinux.org/sl/ I'll continue to check tools that run directly under linux without too big dependencies, after I'll maybe give a try to solutions like stresslinux, memtest, stress for fedora. Thanks for you answers, I'll continue to investigate

  Read the article

• Chipset GPU causes a massive slowdown

  - by zyboxenterprises

  My AMD Radeon HD 7700 recently broke (fan stopped working and GPU overheated), and now I'm running on internal chipset graphics, and it causes a massive slowdown of the whole PC. I've changed the graphics memory from 32MB (minimum) to 256MB (highest), and it hasn't made any difference whatsoever. I'm using Windows Aero, and disabling it should have made a small difference, but it didn't; the whole PC is still slow. I know that it's not the computer build, because I built it myself, and it was a lot faster when it had the AMD Radeon HD 7700 in it, which is the reason why I believe it's the internal chipset graphics that are causing the problem. Is this behavior normal? I don't have the cash right now to go out and buy a new dedicated GPU. I'm using an ASRock N68C-GS FX motherboard with an AMD FX 4100 (overclocked to 4.3GHZ), with 4GB RAM. The overclock was an attempt to resolve this issue, and it isn't related to this issue that the integrated graphics is causing a slowdown.

  Read the article

• Apache conf for high trafic CMS with backend users?

  - by Annan

  I'm in the situation where a website is going to have a high number of web users and a few backend webmasters. Webmasters will upload images (+other high mem tasks) and this bumps up the memory allocation of the httpd child processes to 100-150mb. In order to stop swapping I'm currently setting MaxClients in httpd.conf to 20. However this lowers maximum simultaneous requests. Will this be a problem when the website goes live? What is the best configuration? Info: Drupal 6, PHP 5, Apache 2.2 (Prefork atm) I'm thinking about Worker MPM, two apache instances or low MaxRequestsPerChild.

  Read the article

• Is a computer's DRAM size not as important once we get a Solid State Drive?

  - by Jian Lin

  I am thinking of getting a Dell X11 netbook, and it can go up to 8GB of DRAM, together with a 256GB Solid State Drive. So in that case, it can handle quite a bit of Virtual PC running Linux, and Win XP, etc. But is the 8GB of RAM not so important any more? Won't 2GB or 4GB be quite good if a Solid State Drive is used? I think the most worrying thing is that the memory is not enough and the less often used data is swapped to the pagefile on hard disk and it will become really slow, but with an SSD drive, the problem is a lot less of a concern? Is there a comparison as to, if DRAM speed is n, then SSD drive speed is how many n and hard disk speed is how many n just as a ball park comparison?

  Read the article

• Need help upgrading MacBookPro3,1 RAM to 4GB.

  - by Fantomas

  My questions are: 1) Where to buy it and what to buy? I have heard that this RAM is generic enough and it does not have to come from Apple. 2) Can I reuse my existing stick(s)? Would I have a single 2GB module, or 2 x 1GB modules? 3) If I have 2GB already, is it a good idea to have one old stick and one new one? Which one is better placed at the top and which one at the bottom? Let me know what questions you have. My computer's info: Hardware Overview: Model Name: MacBook Pro Model Identifier: MacBookPro3,1 Processor Name: Intel Core 2 Duo Processor Speed: 2.4 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache: 4 MB Memory: 2 GB Bus Speed: 800 MHz Boot ROM Version: MBP31.0070.B07 SMC Version (system): 1.16f11

  Read the article

• Add entire 300 GB filesystem to Git Annex repository?

  - by Ryan Lester

  By default, I get an error that I have too many open files from the process. If I lift the limit manually, I get an error that I'm out of memory. For whatever reason, it seems that Git Annex in its current state is not optimised for this sort of task (adding thousands of files to a repository at once). As a possible solution, my next thought was to do something like: cd / find . -type d | git annex add --$NONRECURSIVELY find . -type f | git annex add # Need to add parent directories of each file first or adding files fails The problem with this solution is that there doesn't seem from the documentation to be a way to non-recursively add a directory in Git Annex. Is there something I'm missing or a workaround for this? If my proposed solution is a dead end, are there other ways that people have solved this problem?

  Read the article

• The cache is getting at full level so fast

  - by CompilingCyborg

  Please, the memory and the cache are getting to the full level quite quickly under my linux mint 9 - isadora system. I used Ubuntu and Debian before, and it was not causing this issue at all. At the current time i typing the following command frequently to empty the cache "echo 3 /proc/sys/vm/drop_caches". Please any way around this? or do you know what's going wrong? | I am only programming on this machine; no graphics, no games nothing. Thanks in advance for your help!

  Read the article

• memtest incorrectly recognizes my RAM

  - by Brendan Abel

  I recently built a computer and randomly got a couple blue screens. I've run memtest and one of the memory sticks consistently throws memtest errors, while the other does not. The odd part is, memtest lists the following settings for my RAM: RAM: 535 MHz DDR 107 / CAS 2.5-1-3-1 DDR1 128 bits But my RAM is DDR3 1600? Memtest also lists my cpu as AMD K8, even though it's K10. I've probably going to RMA the ram stick, but I just wanted to see if anyone had any insight into the weird memtest stats.

  Read the article

• How does one go about fixing a pixelation issue?

  - by Tyler

  I've been having a lot of trouble with pixelation and also in-game display driver crashes. At first I thought the problem may have been my graphics card (Sapphire 5750) but I have RMA'd it three times and I'm still having trouble. So what I think it might be is my PSU, its 650Watt but its made by Azza so it was cheap and not made by a necessarily good company. Or maybe it could be the CPU (AMD Phenom Black Edition 3.4Ghz) It runs hot (60C) but it passes Everest's test. Someone told me it could be the memory (8GB DDR3) but I don't really see how RAM has anything to do with my problem. So what are some of you suggestions? Here is a video a made awhile ago of what is happening. http://www.metacafe.com/watch/4392213/ati_radeon_5750/ That was just a stress test most games tend to just freeze and crash or lock my system up.

  Read the article

• How to diagnose RAM?

  - by x-man

  I have a java process that is aborted after a while with SIGSEGV. It started to happen after I upgraded the server with more RAM. Having tested on different JVMs I suspect it might be a hardware problem. But no problem was detected by memtest86. So, what else can I do to detect the source of the problem is? Should I take the RAM modules one by one to detect the faulty module? The server is running on 64bit OpenSuse11.3. The memory is not an ECC one it seems. I have a kit of this (3*4GB * 2 = 24GB): http://www.kingston.com/datasheets/KHX1600C9S3K2_8GX.pdf

  Read the article

• My laptop suppose to have 6 GB ram but it's only 2 GB installed

  - by monablo

  My laptop is supposed to have 6 GB ram but it only detects 2 GB of it, so I don't know what to do. I searched the web for answer and what i get that there's 2 possible problem: 1- That 4 GB ram card is broken and not working 2- or the 2 ram card have a different path so the windows chose the path of the smaller ram card which would be the 2 GB ram I don't know what is the path in first place so I really don't know what to do. How would I troubleshoot, and work out why the 4 GB stick is not being detected? My laptop's specifications are as follows: Windows 7 Home premium 64- bit Operating system processor : intel (R) core(TM) i7 CPU Q740 @1.73 GHz 1.73GHz installed memory(RAM) : 2.00 GB (but it suppose to be 6 GB -_- ) My laptop is Dell and it's Model N5010

  Read the article

• I keep getting blue screen - Windows 7 x64 (maybe ram?)

  - by Lostman

  I have +- 5yrs old pc runnig windows 7 and I've been getting blue screen recently. I had win 8 and I got a lof of erros with ram memory, so I reinstalled back to Win 7. (I have 2x 2 GB RAM) To make a better image of my errors - I get them while writing email, installing nvidia driver, sound driver, running RAM test. I got a log of my last error, could anyone tell me what is it? Should I get new RAM memories? The last log I got: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 1029 Additional information about the problem: BCCode: 1a BCP1: 0000000000000403 BCP2: FFFFF680004FAEA0 BCP3: 380000007594A867 BCP4: FFFF6680004FAEA0 OS Version: 6_1_7600 Service Pack: 0_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\062513-16156-01.dmp C:\Users\Boss\AppData\Local\Temp\WER-32156-0.sysdata.xml Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt MemTest86+ Error:

  Read the article

• Real RAM latency

  - by user32569

  Hi, very quick question. When I look for RAM timing, I got 2 different explanations on what is CAS latency. First states, its the time after command to read has been issued from CPU and data are send to data bus. Second says its time betwen column in memory layout has been activated. So, where is the truth? I mean, when I want to know total RAM latenci, in case 1, ot would be just CAS times one clock time. In second case, it would be CAS+other things like RAstoCAS and so times one clock time. Thanks.

  Read the article

• RAM Part Numbers - Meaning?

  - by 1Up

  I hope this is the appropriate stackexchange to post this question. EDIT: I'm attempting to replace faulty ram and am trying to understand the meanings of the label to make correct decision. I have a 2gb stick of ram which appears to have gone bad. It is a SAMSUNG Top line: 2GB 1Rx8 PC3-10600U-9-10-A0 The part number: M378B5773CH0-CH9 1051 Doing a number of searches, I end up here: http://www.reusetek.com/samsung-m378b5773ch0-ch9-1110-4gb-2x2gb-1rx8-pc310600u-09-10-a0-ddr3-desktop-memory/ M378B5773CH0-CH9 1110 Notice there is a difference: 1051 OR 1110 What is the meaning of the part number, and the last 4 digits? Is this a significant difference, and one that affects the machine?

  Read the article

• Which has a faster data transfer rate? WIFI (tablet or cell phone, not LTE) or MicroSD (Class 10)?

  - by techaddict

  Which of the two methods of dta transfer trasfers data at a faster rate for smartphones and tablets? Standard WIFI, or MicroSD Cards? I wonder if it would be actually faster to access data on external storage then it would be to have the MicroSD card in my smartphone or tablet. Currently I have a class 10 32GB MicroSD card in my cell phone. I am looking to get the new Google Nexus tablet but it does not offer expandable internal storage. I wonder if that's really a detriment; because if WIFI is faster than MicroSD, then it would matter almost none at all that you couldn't expand the storage internally. If the case is that WIFI is faster, and people caught onto this, then people could save a lot of money on lower memory ipads/iphones/ipods, tablets, and smartphones!

  Read the article

• PC3200 RAM in Older Computer?

  - by skaz

  Hello all, I am inheriting a Dell Dimension 8200, but it needs RAM to get up and running. I have PC3200 sticks lying around, but I am not sure how to go about figuring out if the RAM is compatible, as RAM has always confused me. Here is the Dell Dimension 8200 Tech Specs: http://support.dell.com/support/edocs/systems/dim8200/specs.htm For RAM, it says: Memory type PC800 (non-ECC) I don't know if that is just the kind that comes with it, and I can put in PC3200 (I think, if it worked, this would run at the lower rating? Is that true?), or if that means only PC800 is compatible. Any help would be appreciated.

  Read the article

< Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >