Search Results

Search found 2772 results on 111 pages for 'hour'.

Page 104/111 | < Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >

  • PC: Quick Freeze, then BSOD, then forced reboot, then freezes again

    - by cr0z3r
    Lately I have been experiencing a weird issue. My PC will hang for a second and then BSOD - it stays there, so I have to reboot. Once Windows starts again and I'm logged in, after 1-10min it freezes again, this time without BSOD. RECAP: 1 second freeze BSOD, hangs there I have to force-reboot Once PC rebooted, I log back into Windows second freeze between a 1-10min range, no BSOD (alternatively, I get a freeze with a constant sound/noise, no BSOD) I contacted my PC provider, who told me my graphics-card might be flawed (Quadro 4000), so I used a Quadro 2000 that they lend me. The issue still occurred. The issue now seemed to belong to a flawed RAM module. Following my provider's steps, I removed all but the first from the left column and kept using my PC for a week or so without any issues. I then added the bottom-right module, and so on, until all modules were back inside - I had no problems. Now it seemed that a simple take-out-put-back-in of the RAM modules had fixed the issue. However, after a few months, the issue was back. I redid all the RAM-swapping I had done before, and concluded that the lower-right module was flawed. My provider changed it for another, and everything was great until now. My PC froze again for barely a second, hanged on a BSOD, I rebooted it, logged-in to Windows to get a freeze (without BSOD or reboot) 40 seconds later. Something worth noting, is that every time I reboot after the BSOD, it is something within Chrome that freezes my PC (e.g. this time I clicked the "restore" button as Chrome mentioned it had exited unexpectedly - from the previous freeze obviously - and it instantly froze). Finally, the Event Viewer lists 2 critical events in the past hour as "ID: 41, Type: Kernel-Power". PC-Specs: http://i.imgur.com/VZpbr.jpg Previous Dump-files: https://dl.dropbox.com/u/716600/DumpFiles_08_2012.zip I would like to thank anybody in advance for your help. You're great. UPDATE 1: I realized that I did not mention an awkward fact about this issue. After I have gotten the 1-sec freeze followed by a BSOD, after I rebooted because the BSOD hanged, and after I logged back in to get another (this time, eternal) freeze and rebooted once again, the PC does not boot back up. The power-light is on, but my monitor says "no signal", as if the PC wouldn't really be turned on. This truly seems a like a power-related issue, doesn't it? UPDATE 2: I just got a freeze, but without BSOD. My screen froze (while on Chrome, which is starting to seem suspicious to me) with an ongoing sound/noise. I had to force-reboot my PC. I would say this is a graphics-card issue, but this issue also happened when I was using the Quadro 2000 from my provider. UPDATE 3: I just got a BSOD while trying to render something (quite heavy, actually) in 3ds Max 2012. I left the BSOD "running", as it said it was writing dump files to disk. However, the percentage number stayed at 0, so after 15 minutes I force-rebooted. I then used the software WhoCrashed (thank you Dave) which reported the following from the C:\Windows\Memory.dmp file: On Thu 22.11.2012 22:13:45 GMT your computer crashed crash dump file: C:\Windows\memory.dmp uptime: 01:05:27 This was probably caused by the following module: Unknown () Bugcheck code: 0x124 (0x0, 0xFFFFFA80275AC028, 0xF200001F, 0x100B2) Error: WHEA_UNCORRECTABLE_ERROR Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA). This is likely to be caused by a hardware problem problem. This problem might be caused by a thermal issue. A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: Unknown . Google query: Unknown WHEA_UNCORRECTABLE_ERROR

    Read the article

  • cron.daily not running at the time it should?

    - by Mariano Martinez Peck
    My /etc/cron.daily scripts seem to be executing far later from what I understand they should. I am in Ubuntu and anacron is installed. If I do a sudo cat /var/log/syslog | grep cron I get something like: Aug 23 01:17:01 mymachine CRON[25171]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 02:17:01 mymachine CRON[25588]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:17:01 mymachine CRON[26026]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:25:01 mymachine CRON[30320]: (root) CMD (test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily )) Aug 23 04:17:01 mymachine CRON[26363]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 05:17:01 mymachine CRON[26770]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 06:17:01 mymachine CRON[27168]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:17:01 mymachine CRON[27547]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:30:01 mymachine CRON[2249]: (root) CMD (start -q anacron || :) Aug 23 07:30:02 mymachine anacron[2252]: Anacron 2.3 started on 2014-08-23 Aug 23 07:30:02 mymachine anacron[2252]: Will run job `cron.daily' in 5 min. Aug 23 07:30:02 mymachine anacron[2252]: Jobs will be executed sequentially Aug 23 07:35:02 mymachine anacron[2252]: Job `cron.daily' started As you can see, at 3:25 it tried to do something. But the cron.daily execution started really at 7:35. My /etc/crontab is: # /etc/crontab: system-wide crontab # Unlike any other crontab you don't have to run the `crontab' # command to install the new version when you edit this file # and files in /etc/cron.d. These files also have username fields, # that none of the other crontabs do. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 3 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) # From what I understand, daily scripts are indeed for 3:25. My /etc/anacrontab is: # /etc/anacrontab: configuration file for anacron # See anacron(8) and anacrontab(5) for details. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HOME=/root LOGNAME=root # These replace cron's entries 1 5 cron.daily run-parts --report /etc/cron.daily 7 10 cron.weekly run-parts --report /etc/cron.weekly @monthly 15 cron.monthly run-parts --report /etc/cron.monthly So...does someone know why my cron started to do something at 3:25 but then really start the jobs at 7:35? Also..as you can see in the log, hourly jobs are being executed at correct time: hour and 17 minutes, which is exactly what I have in /etc/crontab Finally, from the logs, it seems my daily jobs are being actually run by anacron rather than cron? So cron finds nothing to run (at 3:25) and then anacron runs the jobs at 7:35? If true, how can I fix this? Thanks in advance,

    Read the article

  • rdiff-backup is taking longer and longer every time it runs

    - by Jakobud
    I've been running rdiff-backup for the past week or so, every night at 4am. It started out not taking that long, but its taking longer and longer and longer every time its runs every night. In some cases there are quite a few new and changed files and in other cases, not so much. It started out taking < 10 minutes, and after a week its taking over 4.5 hrs to run. Take a look at my session stats below: StartTime 1268046002.00 (Mon Mar 8 04:00:02 2010) EndTime 1268046373.50 (Mon Mar 8 04:06:13 2010) ElapsedTime 371.50 (6 minutes 11.50 seconds) SourceFiles 213928 SourceFileSize 277271282225 (258 GB) MirrorFiles 213914 MirrorFileSize 276693097638 (258 GB) NewFiles 16 NewFileSize 578209911 (551 MB) DeletedFiles 2 DeletedFileSize 2598 (2.54 KB) ChangedFiles 27 ChangedSourceSize 5195150 (4.95 MB) ChangedMirrorSize 5217876 (4.98 MB) IncrementFiles 0 IncrementFileSize 0 (0 bytes) TotalDestinationSizeChange 578184587 (551 MB) Errors 0 StartTime 1268132402.00 (Tue Mar 9 04:00:02 2010) EndTime 1268134341.29 (Tue Mar 9 04:32:21 2010) ElapsedTime 1939.29 (32 minutes 19.29 seconds) SourceFiles 213963 SourceFileSize 307959842562 (287 GB) MirrorFiles 213928 MirrorFileSize 277271282225 (258 GB) NewFiles 37 NewFileSize 31265005547 (29.1 GB) DeletedFiles 2 DeletedFileSize 576511960 (550 MB) ChangedFiles 25 ChangedSourceSize 5243761 (5.00 MB) ChangedMirrorSize 5177011 (4.94 MB) IncrementFiles 65 IncrementFileSize 577266412 (551 MB) TotalDestinationSizeChange 31265826749 (29.1 GB) Errors 0 StartTime 1268218802.00 (Wed Mar 10 04:00:02 2010) EndTime 1268225230.15 (Wed Mar 10 05:47:10 2010) ElapsedTime 6428.15 (1 hour 47 minutes 8.15 seconds) SourceFiles 213971 SourceFileSize 307960643843 (287 GB) MirrorFiles 213963 MirrorFileSize 307959842562 (287 GB) NewFiles 9 NewFileSize 694087 (678 KB) DeletedFiles 1 DeletedFileSize 894 (894 bytes) ChangedFiles 38 ChangedSourceSize 30656167797 (28.6 GB) ChangedMirrorSize 30656059709 (28.6 GB) IncrementFiles 48 IncrementFileSize 289278151 (276 MB) TotalDestinationSizeChange 290079432 (277 MB) Errors 0 StartTime 1268305202.00 (Thu Mar 11 04:00:02 2010) EndTime 1268312788.15 (Thu Mar 11 06:06:28 2010) ElapsedTime 7586.15 (2 hours 6 minutes 26.15 seconds) SourceFiles 213971 SourceFileSize 307960643779 (287 GB) MirrorFiles 213971 MirrorFileSize 307960643843 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 15 ChangedSourceSize 30650824127 (28.5 GB) ChangedMirrorSize 30650824191 (28.5 GB) IncrementFiles 16 IncrementFileSize 689437042 (657 MB) TotalDestinationSizeChange 689436978 (657 MB) Errors 0 StartTime 1268391601.00 (Fri Mar 12 04:00:01 2010) EndTime 1268400145.85 (Fri Mar 12 06:22:25 2010) ElapsedTime 8544.85 (2 hours 22 minutes 24.85 seconds) SourceFiles 213974 SourceFileSize 307960784445 (287 GB) MirrorFiles 213971 MirrorFileSize 307960643779 (287 GB) NewFiles 5 NewFileSize 269587 (263 KB) DeletedFiles 2 DeletedFileSize 128921 (126 KB) ChangedFiles 16 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 26 IncrementFileSize 818279963 (780 MB) TotalDestinationSizeChange 818420629 (781 MB) Errors 0 StartTime 1268478002.00 (Sat Mar 13 04:00:02 2010) EndTime 1268488740.33 (Sat Mar 13 06:59:00 2010) ElapsedTime 10738.33 (2 hours 58 minutes 58.33 seconds) SourceFiles 213974 SourceFileSize 307960784238 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784445 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 16 ChangedSourceSize 30650823920 (28.5 GB) ChangedMirrorSize 30650824127 (28.5 GB) IncrementFiles 19 IncrementFileSize 1041846015 (994 MB) TotalDestinationSizeChange 1041845808 (994 MB) Errors 0 StartTime 1268560803.00 (Sun Mar 14 04:00:03 2010) EndTime 1268573194.82 (Sun Mar 14 07:26:34 2010) ElapsedTime 12391.82 (3 hours 26 minutes 31.82 seconds) SourceFiles 213974 SourceFileSize 307960784238 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784238 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 14 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 15 IncrementFileSize 1116911810 (1.04 GB) TotalDestinationSizeChange 1116911810 (1.04 GB) Errors 0 StartTime 1268647203.00 (Mon Mar 15 04:00:03 2010) EndTime 1268662364.88 (Mon Mar 15 08:12:44 2010) ElapsedTime 15161.88 (4 hours 12 minutes 41.88 seconds) SourceFiles 214010 SourceFileSize 307963430178 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784238 (287 GB) NewFiles 37 NewFileSize 2684172 (2.56 MB) DeletedFiles 1 DeletedFileSize 5348 (5.22 KB) ChangedFiles 32 ChangedSourceSize 30656134913 (28.6 GB) ChangedMirrorSize 30656167797 (28.6 GB) IncrementFiles 71 IncrementFileSize 1316460362 (1.23 GB) TotalDestinationSizeChange 1319106302 (1.23 GB) Errors 0 StartTime 1268733603.00 (Tue Mar 16 04:00:03 2010) EndTime 1268750396.76 (Tue Mar 16 08:39:56 2010) ElapsedTime 16793.76 (4 hours 39 minutes 53.76 seconds) SourceFiles 214010 SourceFileSize 307963430156 (287 GB) MirrorFiles 214010 MirrorFileSize 307963430178 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 15 ChangedSourceSize 30650823898 (28.5 GB) ChangedMirrorSize 30650823920 (28.5 GB) IncrementFiles 16 IncrementFileSize 936032413 (893 MB) TotalDestinationSizeChange 936032391 (893 MB) Errors 0 StartTime 1268820002.00 (Wed Mar 17 04:00:02 2010) EndTime 1268834619.90 (Wed Mar 17 08:03:39 2010) ElapsedTime 14617.90 (4 hours 3 minutes 37.90 seconds) SourceFiles 214010 SourceFileSize 307963430156 (287 GB) MirrorFiles 214010 MirrorFileSize 307963430156 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 14 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 15 IncrementFileSize 1289272860 (1.20 GB) TotalDestinationSizeChange 1289272860 (1.20 GB) Errors 0 Is this common behavior? It's only about 300gigs of data total. One important thing to note though, rdiff-backup is backup up stuff over to a USB2 external drive. Maybe thats why its so slow?

    Read the article

  • How to transfer data between two networks efficiently

    - by Tono Nam
    I would like to transfer files between two places over the internet. Right now I have a VPN and I am able to browse, download and transfer files. So my question is not really how to transfer the files; Instead, I would like to use the most efficient approach because the two places constantly share a lot of data. The reason why I want to get rid of the VPN is because it is two slow. Having high upload speed is very expensive/impossible in residential places so I would like to use a different approach. I was thinking about using programs such as http://www.dropbox.com . The problem with Dropbox is that the free version comes with only 2 GB of storage. I think the deals they offer are OK and I might be willing to pay to get that increase in speed. But I am concerned with the speed of transferring data. Dropbox will upload the file to their server then send it from the server to the other location. I would like it to be even faster. Anyway I was thinking why not create a program myself. This is the algorithm that I was thinking of. Let me know if it sounds too crazy. (Remember my goal is to transfer files as fast as possible) Things that I will use in this algorithm: Server on the internet called S (Has fast download and upload speed. I pay to host a website and some services in there. I want to take advantage of it.) Client A at location 1 Client B at location 2 So lets say at location 1, 20 large files are created and need to be transferred to location 2. Client A compresses the files with the highest compression ratio possible. Client A starts sending data via UDP to client B. Because I am using UDP I will include the sequence number on each packet. Have server S help speed up things. For example every time a packet is lost we can use Server S to inform client A that it needs to resend a packet. Anyways I think this approach will increase the transfer rate. I do not know if it is possible to start sending data while it is being compressed. Or if it is possible to start decompressing data even if we are not done receiving the whole file. Maybe it will be faster to start sending the files right away without compressing. If I knew that I will always be sending large text files then I will obviously use the compression. I need this as a general algorithm. So I guess my question is could I increase performance by using UDP instead of TCP and by using an extra server to keep track of lost packets? And how should I compress files before sending? Compressing a 1 GB file with the highest compression ratio takes about 1 hour! I would like to take advantage of that time by sending it as it is being compressed.

    Read the article

  • How to transfer data between two netowks efficiently

    - by Tono Nam
    I will like to transfer files between two places over the internet. Right now I have a VPN and I am able to browse, download and transfer files. So my question is not really how to transfer the files; Instead, I will like to use the most efficient approach because the two places constantly share a lot of data. The reason why I want to get rid of the vpn is because it is two slow. Having high upload speed is very expensive/impossible on residential places so I will like to use a different approach. I was thinking about using programs such as http://www.dropbox.com . The problem with dropbox is it only enables 2 GB of storage in order for it to be free. I think the deals they offer are ok and I might be willing to pay to get that increase in speed. But I am concerned with the speed of transferring data. Dropbox will upload the file to their server then send it from the server to the other location. I will like it even faster lol. Anyways I was thinking why not create a program my self. This is the algorithm that I was thinking let me know if it sounds to crazy. (remember my goal is to transfer files as fastest as possible) Things that I will use in this algorithm: Server on the internet called S ( has fast download and upload speed. I pay to host a website and some services in there. I want to take advantage of it) Client A on location 1 Client B on location 2 So lets say on location 1 20 large files are created and need to be transferred to location 2. Client A compresses the files with the highest compression ratio possible. Client A starts sending data via UDP to client B. Because I am using UDP I will include the sequence number on each package. Have server S help speed up things. For example every time a package is lost we can use Server S to inform client A that it needs to resend a package. Anyways I think this approach will increase the transfer rate. I do not know if it is possible to start sending data meanwhile it is being compressed. Also if it is possible to start decompressing data even if we are not done receiving all the info. Maybe it will be faster to start sending the files right away without compressing. If I knew that I will always be sending large text files then I will obviously use the compression. I need this as a general algorithm. So i guess my question is should using UDP over TCP could increase performance by using an extra server to keep track of lost packages? and How should I compress files before sending? compressing a 1 GB file with the highest compression ration takes about 1 hour! I will like to take advantage of that time by sending it meanwhile it is compressed.

    Read the article

  • How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

    - by cagenut
    Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

    Read the article

  • phpmyadmin login redirect fails with custom ssl port

    - by baraboom
    The server is running Ubuntu 10.10, Apache 2.2.16, PHP 5.3.3-1ubuntu9.3, phpMyAdmin 3.3.7deb5build0.10.10.1. Since this same server is also running Zimbra on port 443, I've configured apache to serve SSL on port 81. So far, I have one CMS script running on this virtual host successfully. However, when I access /phpmyadmin (set up with the default alias) on my custom ssl port and submit the login form, I am redirected to http://vhost.domain.com:81/index.php?TOKEN=foo (note the http:// instead of the https:// that the login url was using). This generates an Error 400 Bad Request complaining about "speaking plain HTTP to an SSL-enabled server port." I can then manually change the http:// to https:// in the URL and use phpmyadmin as expected. I was annoyed enough to spend an hour trying to fix it and now even more annoyed that I cannot figure it out. I've tried various things, including: Adding $cfg['PmaAbsoluteUri'] = 'https://vhost.domain.com:81/phpmyadmin/'; to the /usr/share/phpmyadmin/config.inc.php file but this did not correct the problem (even though /usr/share/phpmyadmin/libraries/auth/cookie.auth.lib.php looks like it should honor it and use it as the redirect). Adding $cfg['ForceSSL'] = 1; to the same config.inc.php but then apache spirals into an infinite redirect. Adding a rewrite rule to the vhost-ssl conf file in apache but I was unable to figure out the condition to use when http:// was present along with the correct ssl port of :81. Lots of googling. Here are the relevant Apache configuration pieces: /etc/apache2/ports.conf <IfModule mod_ssl.c> NameVirtualHost *:81 Listen 81 </IfModule> /etc/apache2/sites-enabled/vhost-nonssl <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost.domain.com DocumentRoot /home/xxx/sites/vhost/html RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_HOST}:81%{REQUEST_URI} </Virtualhost> /etc/apache2/sites-enabled/vhost-ssl <VirtualHost *:81> ServerAdmin webmaster@localhost ServerName vhost.domain.com DocumentRoot /home/xxx/sites/vhost/html <Directory /> Options FollowSymLinks AllowOverride None AuthType Basic AuthName "Restricted Vhost" AuthUserFile /home/xxx/sites/vhost/.users Require valid-user </Directory> <Directory /home/xxx/sites/vhost/html/> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> /etc/apache2/conf.d/phpmyadmin.conf Alias /phpmyadmin /usr/share/phpmyadmin (The rest of the default .conf truncated.) Everything in the apache config seems to work ok - the rewrite from non-ssl to ssl, the http authentication, the problem only happens when I am submitting the login form for phpmyadmin from https://vhost.domain.com:81/index.php. Other configs: The phpmyadmin config is completely default and the php.ini has only had some minor changes to memory and timeout limits. These seem to work fine, as mentioned, another php script runs with no problem and phpmyadmin works great once I manually enter in the correct schema after login. I'm looking for either a bandaid I can add to save me the trouble of manually entering in the https:// after login, a real fix that will make phpmyadmin behave as I think it should or some greater understanding of why my desired config is not possible.

    Read the article

  • IP Micro-outages, telephone micro-outages, and CATV micro-outages

    - by Michael Graff
    This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

    Read the article

  • iPhone doesn't save password for Cisco IPsec VPN using racoon daemon

    - by dsx
    On my Debian server I had set up racoon daemon (1:0.8.0-14) for Cisco IPSec VPN using certificates for authentication. My racoon.conf is like following: log info; path certificate "/etc/racoon/certs"; listen { isakmp $SERVER_IP_HERE [500]; isakmp_natt $SERVER_IP_HERE [4500]; } timer { natt_keepalive 10 sec; } remote anonymous { lifetime time 24 hours; proposal_check obey; passive on; exchange_mode aggressive,main; my_identifier asn1dn; peers_identifier asn1dn; verify_identifier on; certificate_type x509 "cert_name.crt" "key_name.key"; ca_type x509 "ca.crt"; mode_cfg on; verify_cert on; ike_frag on; generate_policy on; nat_traversal on; dpd_delay 20; proposal { encryption_algorithm aes; hash_algorithm sha1; authentication_method xauth_rsa_server; dh_group modp1024; } } mode_cfg { conf_source local; auth_source system; auth_throttle 3; save_passwd on; dns4 8.8.8.8; network4 $SOME_LAN_SUBNET; netmask4 255.255.255.0; pool_size 128; } sainfo anonymous { pfs_group 2; lifetime time 24 hour; encryption_algorithm aes; authentication_algorithm hmac_sha1; compression_algorithm deflate; } I'm not using PSK authentication here. Using iPhone configuration utility I had uploaded all required certificates to iPhone and set up VPN on demand. Everything works just fine except one thing: iPhone refuses to save VPN password regardless of save_passwd on; in racoon configuration file. As opposed to iPhone behaviour, Mac OS X 10.8.2 have no problems saving password. I had examined iPhone log file and found following: racoon[151] <Notice>: >>>>> phase change status = phase 1 established configd[50] <Notice>: IPSec Network Configuration started. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = $SUBNET_IP_HERE. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0. configd[50] <Notice>: IPSec Network Configuration: SAVE-PASSWORD = 0. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-DNS = 8.8.8.8. configd[50] <Notice>: IPSec Network Configuration: BANNER = . configd[50] <Notice>: IPSec Network Configuration: DEF-DOMAIN = . configd[50] <Notice>: IPSec Network Configuration: DEFAULT-ROUTE = local-address $SUBNET_IP_HERE/32. configd[50] <Notice>: IPSec Phase2 starting. configd[50] <Notice>: IPSec Network Configuration established. configd[50] <Notice>: IPSec Phase1 established. Please note IPSec Network Configuration message containing SAVE-PASSWORD = 0.. Is it a bug in racoon daemon on server, or iPhone (iOS version is 6.0.1 (10A523)) or it is me missing something? How to make iPhone remember IPSec VPN password?

    Read the article

  • Slow disk transfer rate

    - by Nooklez
    I have problem with slow disk transfer rate. It's static files server for our website. I was making backup of data and noticed that tar is very slow. So I did hdparm -t and... hdparm -t /dev/sda3 /dev/sda3: Timing buffered disk reads: 6 MB in 4.70 seconds = 1.28 MB/sec It's low traffic hour now on our site, so huge I/O traffic is not a reason (iotop show less than 1 MB/s). It's RAID10 setup (2x2 SATA drives). Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-10 OK - - 64K 1396.96 W ON VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 698.63 GB SATA 0 - WDC WD7500AADS-00M2 p1 OK u0 698.63 GB SATA 1 - WDC WD7500AADS-00M2 p2 OK u0 698.63 GB SATA 2 - WDC WD7500AADS-00M2 p3 OK u0 698.63 GB SATA 3 - WDC WD7500AADS-00M2 We have recently changed almost all components of server (excluding 3ware controller + disks). And I think problems started since then. Can it be configuration problem or hardware? EDIT: I found something like that in dmesg [166843.625843] irq 16: nobody cared (try booting with the "irqpoll" option) [166843.625846] Pid: 0, comm: swapper Not tainted 3.1.5-gentoo #3 [166843.625847] Call Trace: [166843.625848] <IRQ> [<ffffffff810859d5>] __report_bad_irq+0x35/0xc1 [166843.625856] [<ffffffff81085cec>] note_interrupt+0x165/0x1e1 [166843.625859] [<ffffffff8108445f>] handle_irq_event_percpu+0x16f/0x187 [166843.625861] [<ffffffff810844a9>] handle_irq_event+0x32/0x51 [166843.625863] [<ffffffff8108640b>] handle_fasteoi_irq+0x75/0x99 [166843.625866] [<ffffffff810039d7>] handle_irq+0x83/0x8b [166843.625868] [<ffffffff810036ad>] do_IRQ+0x48/0xa0 [166843.625871] [<ffffffff8155082b>] common_interrupt+0x6b/0x6b [166843.625872] <EOI> [<ffffffff812981e8>] ? acpi_safe_halt+0x22/0x35 [166843.625877] [<ffffffff812981e2>] ? acpi_safe_halt+0x1c/0x35 [166843.625879] [<ffffffff81298216>] acpi_idle_do_entry+0x1b/0x2b [166843.625881] [<ffffffff81298276>] acpi_idle_enter_c1+0x50/0x99 [166843.625884] [<ffffffff813b792a>] cpuidle_idle_call+0xed/0x171 [166843.625886] [<ffffffff81001257>] cpu_idle+0x55/0x81 [166843.625888] [<ffffffff81532a69>] rest_init+0x6d/0x6f [166843.625891] [<ffffffff81aa1aca>] start_kernel+0x329/0x334 [166843.625893] [<ffffffff81aa12a6>] x86_64_start_reservations+0xb6/0xba [166843.625894] [<ffffffff81aa139c>] x86_64_start_kernel+0xf2/0xf9 [166843.625896] handlers: [166843.625898] [<ffffffff812dc8de>] twl_interrupt [166843.625900] Disabling IRQ #16 It's related to problem? EDIT #2: Based on feedback in comments, here is more informations. cat /proc/interrupts 16: 390813 0 0 0 IO-APIC-fasteoi 3w-sas Controller model: [ 1.095350] 3ware Storage Controller device driver for Linux v1.26.02.003. [ 1.095467] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. [ 1.095641] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. [ 1.095787] 3w-sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.095881] 3w-sas 0000:01:00.0: setting latency timer to 64 [ 1.910801] 3w-sas: scsi0: Found an LSI 3ware 9750-4i Controller at 0xfe560000, IRQ: 16. [ 2.216537] 3w-sas: scsi0: Firmware FH9X 5.08.00.008, BIOS BE9X 5.07.00.011, Phys: 8. [ 2.216836] scsi 0:0:0:0: Direct-Access LSI 9750-4i DISK 5.08 PQ: 0 ANSI: 5 And motherboard: description: Motherboard product: P8H67-M vendor: ASUSTeK Computer INC.

    Read the article

  • Intermittent lockups, unable to diagnose in over a year

    - by Magsol
    Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

    Read the article

  • Load average is have been high over some period

    - by user111196
    We have a dedicated MySQL server and below is the a snapshot of the top. The load average has been staying at nearly 100 for an hour plus ready. top - 20:54:28 up 7:31, 2 users, load average: 83.08, 96.88, 106.23 Tasks: 278 total, 2 running, 274 sleeping, 2 stopped, 0 zombie Cpu0 : 18.8%us, 10.2%sy, 0.0%ni, 70.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 51.2%us, 4.3%sy, 0.0%ni, 44.2%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu2 : 9.0%us, 10.3%sy, 0.0%ni, 80.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 18.8%us, 7.4%sy, 0.0%ni, 73.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 7.8%us, 8.8%sy, 0.0%ni, 83.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 10.3%us, 8.4%sy, 0.0%ni, 81.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 6.2%us, 7.5%sy, 0.0%ni, 86.2%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 6.2%us, 6.2%sy, 0.0%ni, 87.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu8 : 8.8%us, 10.4%sy, 0.0%ni, 80.5%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu9 : 63.7%us, 4.6%sy, 0.0%ni, 12.2%id, 0.0%wa, 4.3%hi, 15.2%si, 0.0%st Cpu10 : 9.2%us, 10.2%sy, 0.0%ni, 80.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu11 : 17.3%us, 5.9%sy, 0.0%ni, 76.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu12 : 8.0%us, 8.7%sy, 0.0%ni, 83.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu13 : 10.9%us, 7.4%sy, 0.0%ni, 81.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu14 : 6.2%us, 6.9%sy, 0.0%ni, 86.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu15 : 4.8%us, 6.1%sy, 0.0%ni, 89.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 33009800k total, 23174396k used, 9835404k free, 120604k buffers Swap: 35061752k total, 0k used, 35061752k free, 16459540k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3341 mysql 20 0 14.3g 4.6g 4240 S 417.8 14.5 1673:51 mysqld 24406 root 20 0 15008 1292 876 R 0.3 0.0 0:00.19 top 1 root 20 0 4080 852 608 S 0.0 0.0 0:01.92 init 2 root 15 -5 0 0 0 S 0.0 0.0 0:00.00 kthreadd 3 root RT -5 0 0 0 S 0.0 0.0 0:00.32 migration/0 4 root 15 -5 0 0 0 S 0.0 0.0 0:00.29 ksoftirqd/0 5 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 6 root RT -5 0 0 0 S 0.0 0.0 0:03.21 migration/1 7 root 15 -5 0 0 0 S 0.0 0.0 0:00.07 ksoftirqd/1 8 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 9 root RT -5 0 0 0 S 0.0 0.0 0:00.17 migration/2 10 root 15 -5 0 0 0 S 0.0 0.0 0:00.03 ksoftirqd/2 11 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/2 12 root RT -5 0 0 0 S 0.0 0.0 0:00.32 migration/3 13 root 15 -5 0 0 0 S 0.0 0.0 0:00.02 ksoftirqd/3 14 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/3 15 root RT -5 0 0 0 S 0.0 0.0 0:00.10 migration/4 16 root 15 -5 0 0 0 S 0.0 0.0 0:00.04 ksoftirqd/4 17 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/4 18 root RT -5 0 0 0 S 0.0 0.0 0:00.35 migration/5 We have also tried to run this command. What else command can help us diagnose the exact problem of this high load? netstat -nat |grep 3306 | awk '{print $6}' | sort | uniq -c | sort -n 1 LISTEN 1 SYN_RECV 410 ESTABLISHED 964 TIME_WAIT Output of vmstat 1: ---------------memory--------------- --swap-- --io-- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 0 0 12978936 30944 15172360 0 0 259 3 184 265 6 6 77 12 0

    Read the article

  • .AVI Files randomly cease to open, other strange errors too

    - by Ben Franchuk
    I Recently (a couple weeks ago) downloaded the complete series of Seinfeld, all in varying file type. I Watched them in sequence according to season and to airing date, and all was well. All of the files played fine with my media player of choice ("BS Player"), and once I had finished, I went onto watch some other TV I had previously downloaded (The U.S. Series of "The Office"), and after then, some other film and then some music, over the following weeks (keep in mind all of these files are all on the same Hard Drive). Later then, More recently, I Went back to watching Seinfeld. The episodes played well as they did before- with the exclusion of a few in Season 7. I Have not tested all of the episodes in the season, but upon inspection, the majority of them are experiencing this problem; the problem being simply that they don't open! BS Player says that the files are either damaged or that the codecs to play the files are not on my computer-- however I am certain that the files DO have the codecs, and I am pretty sure that they are NOT DAMAGED either. I Have played the files with other players (such as VLC, Media Player Classic, and Windows Media Player), too, only to the same result; of them not opening. Seemingly the only way that I can differentiate between a damaged file and a non-damaged file are the way that the icon shows in Windows Explorer. For example, the below image is how explorer shows the information of a file that is non-damaged... ...and below is how a damaged file appears... The most disturbing and confusing part of this, though, is the last episode in the season- It opens, but not as a video- Instead, as a 1 Hour, 16 Minute, and 35 Second Audio file! The file plays a song for the first 4 or so minutes, and then is pretty much silent (except for some extremely quiet noise) until the last minute or so, when a random array of chopped up sounds and beeping noises play. I Do not recognise the song at the beginning of the file, but by the sounds of it, it is a song by the artist "Mr. Oizo," who's complete works I downloaded a couple weeks before now; and a bit before then I had finished downloading season 9 (not affected by these problems) of Seinfeld. I'd also like to note that the file I told of earlier (which played audio instead of video) reads as the same size as the other files in the season (around 175 MB) and also opens as a video clip. I Have NEVER experienced any of these problems in the past, and they seem to be only effecting the one season of my downloaded TV. The problems have not arisen with any of the other files on my Hard Drive, or any of the files downloaded around the time or after the time of which I downloaded season 7 of Seinfeld- or at least to my noticing. I Use the hard drive these files are located on almost every day, so could that be the cause of these problems? Is this a sign that my HDD is soon going to die? If it helps, the HDD is a Western Digital MyBook 1.5 TB 7500 RPM. It is connected to the computer via U.S.B. 2.0. EDIT! I noticed that this problem is now occurring with Season 9 of Seinfeld- and, presumably, other files on the drive I have yet to check. Please, If you have ANY IDEA AT ALL on what may be causing this or how to fix it, do tell me!

    Read the article

  • shinken/nagios discriminative between warning alert and critical alert

    - by SWdream
    i using shinken for my monitoring system. Now, i have a problem when i configure shinken notification. My purpose is to discriminative between notification for warning state and critical state of check service: with warning state: + time to send alert from 8h = 18 h everyday, via email and sms + notification_interval is 60 minutes (Re-notify about service problems every hour) with critical state: + time to send alert : all time (24 x 7), via email and sms + notification_interval is 30 minutes Please show me how to solve my problem! I have tried the following: i configured: + contact templates: define contact{ name warning-contact ; The name of this contact template register 0 ; DONT REGISTER THIS DEFINITION - ITS NOT A REAL CONTACT, JUST A TEMPLATE! host_notifications_enabled 1 define contact{ service_notifications_enabled 1 email shinken@localhost can_submit_commands 1 notificationways email_warning, sms_warning } define contact{ name critical-contact ; The name of this contact template register 0 ; DONT REGISTER THIS DEFINITION - ITS NOT A REAL CONTACT, JUST A TEMPLATE! host_notifications_enabled 1 service_notifications_enabled 1 email shinken@localhost can_submit_commands 1 notificationways email_critical, sms_critical } + time poriod templates: define timeperiod{ timeperiod_name warning alias Normal Work Hours monday 08:00-18:00 tuesday 08:00-18:00 wednesday 08:00-18:00 thursday 08:00-18:00 friday 08:00-18:00 saturday 08:00-18:00 sunday 08:00-18:00 #exclude 24x7 } define timeperiod{ timeperiod_name 24x7 alias 24_Hours_A_Day,_7_Days_A_Week sunday 00:00-24:00 monday 00:00-24:00 tuesday 00:00-24:00 wednesday 00:00-24:00 thursday 00:00-24:00 friday 00:00-24:00 saturday 00:00-24:00 #exclude workhours } + notification way templates: define notificationway{ notificationway_name email_warning service_notification_period warning host_notification_period warning service_notification_options w host_notification_options d,u,r,f,s notification_interval 60 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-email ; send service notifications via email host_notification_commands notify-host-by-email ; send host notifications via email } define notificationway{ notificationway_name email_critical service_notification_period 24x7 host_notification_period 24x7 service_notification_options c,r host_notification_options d,u,r,f,s notification_interval 30 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-email ; send service notifications via email host_notification_commands notify-host-by-email ; send host notifications via email } define notificationway{ notificationway_name sms_warning service_notification_period warning host_notification_period warning service_notification_options w host_notification_options d,u,r,f,s notification_interval 60 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-sms ; send service notifications via sms host_notification_commands notify-host-by-sms ; send host notifications via sms } define notificationway{ notificationway_name sms_critical service_notification_period 24x7 host_notification_period 24x7 service_notification_options c,r host_notification_options d,u,r,f,s notification_interval 30 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-sms ; send service notifications via sms host_notification_commands notify-host-by-sms ; send host notifications via sms } + my contacts define contact{ use warning-contact contact_name thanhwarn email xxxx pager xxxx ; contact phone number } define contact{ use critical-contact contact_name thanhcritical email xxxxx pager 01689xxxx ; contact phone number } + and define service: define service{ use generic-service service_description check_ram host_name graphite contacts thanhcritical, thanhwarn check_command check_nrpe!check_ram } but my shinken system don't send alert. i don't understand this. please show me where I went wrong! thanks all!

    Read the article

  • VPS 512 MB RAM with WordPressMU comes to consumes lots of memory

    - by CAPitalZ
    I have googled for days and gathered all optimization suggestions and tried. My sites are not getting any high hits. May be like 100 hits per day [all my sites combined]. Here are my specs I have 512 MB RAM VPS with burstable 1024 MB. Centos 5 32-bit & cPanel/WHM Apache 2.2 MySQL 5.0 PHP 5.3.2 Here is my Configs I have 2 WordPressMU production sites, and 1 test site my.cnf # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/lib/mysql/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking skip-bdb skip-innodb key_buffer = 16M max_allowed_packet = 1M table_cache = 64 sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M #CAPitalZ thread_cache_size=8 thread_concurrency=4 #query_cache_type=1 #query_cache_limit=1M query_cache_size=16M concurrent_insert=2 low_priority_updates=1 max_connections=50 tmp_table_size=16M max_heap_table_size=16M join_buffer_size=1M interactive_timeout=25 wait_timeout=1000 #connect_timout=10 not able to restart mysql max_connect_errors=10 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # skip-networking # Disable Federated by default skip-federated # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 [mysqld_safe] open_files_limit=8192 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [myisamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout httpd.conf I have unselected many modules and recompiled using EasyApache in WHM. Only have the following modules built Deflate Expires Fileprotect Imagemap MPM Prefork Version [default] EAccelerator for PHP Bcmath Calendar CurlSSL [I'm using Curl. But I don't have any https sites] Expat GD [for image cropping] Gettext Imap Mbregex [default] Mbstring [need both Mbregex and Mbstring for utf-8] Mysql of the system MySQL "Improved" extension. Sockets TTF (FreeType) [I'm using custom font] Zlib Under Global Configuration I only have FollowSymLinks enabled I Have TraceEnable, ServerSignature, FileETag OFF ServerTokens ProductOnly DirectoryIndex Priority has index.php as the first one I have removed Clamd [Clam Anti-virus] SpamAssasin is Off Under Tweak Settings Default catch-all/default address behavior for new accounts. This is set to "fail" All stats programs turned off I have eAccelerator installed and checked in phpinfo and its working [Pre VirtualHost Include under WHM] Timeout 20 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 3 MinSpareServers 1 MaxSpareServers 3 StartServers 1 ServerLimit 50 MaxClients 50 MaxRequestsPerChild 4000 ExtendedStatus Off #ServerType standalone this throws error HostnameLookups Off <Directory "/"> AllowOverride None </Directory> My sites will take ages to load and WHM/CPanel will not even load. adadaa.com/ http://adadaa.net/ kadais.ca/ My average memory consumption is like 1000 MB! [yes always bursting] The process that consumes most CPU and also most memory is mysql But I also get like 15 httpd processes [when its bursting] I already got warning from cpuwatchcheck saying "While processing, the cpu has been maxed out for more than a 6 hour period. The current load/uptime line on the server at the time of this email is 07:00:37 up 11:30, 0 users, load average: 14.64, 16.79, 20.07" I don't know, I have tried switching these config values many different times, but nothing seems to work. Please show some light... Thanks

    Read the article

  • volume group disappeared after xfs_check run

    - by John P
    EDIT** I have a volume group consisting of 5 RAID1 devices grouped together into a lvm and formatted with xfs. The 5th RAID device lost its RAID config (cat /proc/mdstat does not show anything). The two drives are still present (sdj and sdk), but they have no partitions. The LVM appeared to be happily using sdj up until recently. (doing a pvscan showed the first 4 RAID1 devices + /dev/sdj) I removed the LVM from the fstab, rebooted, then ran xfs_check on the LV. It ran for about half an hour, then stopped with an error. I tried rebooting again, and this time when it came up, the logical volume was no longer there. It is now looking for /dev/md5, which is gone (though it had been using /dev/sdj earlier). /dev/sdj was having read errors, but after replacing the SATA cable, those went away, so the drive appears to be fine for now. Can I modify the /etc/lvm/backup/dedvol, change the device to /dev/sdj and do a vgcfgrestore? I could try doing a pvcreate --uuid KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ /dev/sdj to make it recognize it, but I'm afraid that would erase the data on the drive UPDATE: just changing the pv to point to /dev/sdj did not work vgcfgrestore --file /etc/lvm/backup/dedvol dedvol Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Cannot restore Volume Group dedvol with 1 PVs marked as missing. Restore failed. pvscan /dev/sdj: read failed after 0 of 4096 at 0: Input/output error Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. PV /dev/sdd2 VG VolGroup00 lvm2 [74.41 GB / 0 free] PV /dev/md2 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md3 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md0 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md4 VG dedvol lvm2 [931.51 GB / 0 free] PV unknown device VG dedvol lvm2 [1.82 TB / 63.05 GB free] Total: 6 [5.53 TB] / in use: 6 [5.53 TB] / in no VG: 0 [0 ] vgscan Reading all physical volumes. This may take a while... /dev/sdj: read failed after 0 of 4096 at 0: Input/output error /dev/sdj: read failed after 0 of 4096 at 2000398843904: Input/output error Found volume group "VolGroup00" using metadata type lvm2 Found volume group "dedvol" using metadata type lvm2 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 5 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 5 Act PV 5 VG Size 5.46 TB PE Size 4.00 MB Total PE 1430796 Alloc PE / Size 1414656 / 5.40 TB Free PE / Size 16140 / 63.05 GB VG UUID o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246 dedvol { id = "o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246" seqno = 10 status = ["RESIZEABLE", "READ", "WRITE"] flags = [] extent_size = 8192 # 4 Megabytes max_lv = 0 max_pv = 0 physical_volumes { pv0 { id = "Msiee7-Zovu-VSJ3-Y2hR-uBVd-6PaT-Ho9v95" device = "/dev/md2" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv1 { id = "ZittCN-0x6L-cOsW-v1v4-atVN-fEWF-e3lqUe" device = "/dev/md3" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv2 { id = "NRNo0w-kgGr-dUxA-mWnl-bU5v-Wld0-XeKVLD" device = "/dev/md0" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv3 { id = "2EfLFr-JcRe-MusW-mfAs-WCct-u4iV-W0pmG3" device = "/dev/md4" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv4 { id = "KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ" device = "/dev/md5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 3907028992 # 1.81935 Terabytes pe_start = 384 pe_count = 476932 # 1.81935 Terabytes } }

    Read the article

  • I am starting to think that Prevx.com isnt a legit site...but heres my long-winded question

    - by cop1152
    I apologize in advance for the long-winded post. I posted it all because I believe its informative and may be useful. Also, I posted my question at the end. Moments ago I was RDC to a file server in my home (from inside my home). I had opened Firefox and Googled for a manufacturers website. Immediately after clicking the link, Firefox abruptly closed. This seemed odd to me to so I checked the running processes and discovered d.exe, e.exe, and f.exe running. I Googled these processes on a different machine and found them belonging to a key-logger/screen-capturer/trojan called defender.exe, which according to the Prevx lives in c:\documents and settings\user\local settings\temp. (Prevx link http://www.prevx.com/filenames/147352809685142526-X1/DEFENDER32.EXE.html) Simultaneously, an obviously-spoofed Windows Firewall popup appeared on the server asking me to click ‘yes’ to update Windows Firewall. At this time I ended all rogue processes, emptied the temp folder, removed defender.exe from startup, and checked my registry and a few other locations. Before deleting Defender.exe I noted that it was created moments ago, just before Firefox crashed. I believe that I was ‘almost’ infected with this malware. I believe that it needed me to click the phony popup in order to complete infection because it wasn’t allowed to execute processes from the temp folder. After cleaning the machine, I restarted it and have been monitoring it for over an hour. I am debating on whether or not to restore the Windows partition (a separate physical drive from the data) or to just watch it for awhle. I should mention that, because of the specs on this machine, I do not run antivirus software, but I know it well and inspect it regularly. It is a very old Compaq with a 400mhz processer and 512mb of ram. I have a static IP and the server is in the DMZ running an FTP client and some HTTP server software. All files transferred to and stored on this machine are scanned for malware before transferring. Usually the machine only runs 19 processes and performs pretty well for its intended purpose. I posted the story so that you could be aware of a possible new piece of malware and how it acts, but I also have a question or two. First, over the last few months I have noticed that PREVX is listed at the top of most of my Google searches when researching malware, especially for new or obscure malware…and they always want you to purchase something. I don’t think they are one of the top AV companies, so it seems odd that they are always the top Google result. Does anyone have any experience with any of their products? Also, what sites do you rely on for malware researching? Recently, I have found it difficult to find good info because of HijackThis-logs and other deadend info cluttering up my searches. And lastly, besides antivirus, third-party firewall, etc, what settings would you use to lock down a machine to make it more secure in instances where a stubborn admin like myself refuses to run AV? Thanks.

    Read the article

  • How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

    - by cagenut
    Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only The hell you are: [root@localhost ~]# mount -o remount,rw /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

    Read the article

  • "The server closed the connection without sending any data"

    - by Toby
    Server setup The problem Diagnostic information What I've tried Specific Help needed 1. I have the following server setup: Debian Squeeze Linux 2.6.32-5-amd64 Apache2-mpm-prefork 2.2.16-6+squeeze10 PHP 5.3.3-7+squeeze14 This server is protected with the Suhosin Patch 0.9.9.1 Max Requests Per Child: 0 - Keep Alive: on - Max Per Connection: 100 Timeouts Connection: 300 - Keep-Alive: 15 Loaded Modules core mod_log_config mod_logio prefork http_core mod_so mod_alias mod_auth_basic mod_auth_digest mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_cgi mod_deflate mod_dir mod_env mod_mime mod_negotiation mod_php5 mod_reqtimeout mod_rewrite mod_setenvif mod_ssl mod_status Wordpress 3.4.2 (Upgrading to 3.5 soon :) 2. The problem When I restart the server (sudo shutdown -r now), going to any website page results in the following error from the web browser (in this case, Google Chrome, but other browsers also show the same error). This error can also occur an hour or so after all is working ok, seemingly randomly, which is my biggest concern as it means my server is not reliable: No data received Unable to load the web page because the server sent no data. Here are some suggestions: Reload this web page later. Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data. 3. Diagnostic information The apache error log contains the folowing entries: [Fri Dec 14 22:23:27 2012] [notice] child pid 1955 exit signal Floating point exception (8) [Fri Dec 14 22:23:27 2012] [notice] child pid 1956 exit signal Floating point exception (8) [Fri Dec 14 22:23:29 2012] [notice] child pid 1957 exit signal Floating point exception (8) [Fri Dec 14 22:23:30 2012] [notice] child pid 1958 exit signal Floating point exception (8) [Fri Dec 14 22:23:32 2012] [notice] child pid 1959 exit signal Floating point exception (8) [Fri Dec 14 22:23:32 2012] [notice] child pid 1960 exit signal Floating point exception (8) [Fri Dec 14 22:23:34 2012] [notice] child pid 1961 exit signal Floating point exception (8) [Fri Dec 14 22:23:34 2012] [notice] child pid 1962 exit signal Floating point exception (8) 4. What I've tried a) I can 'fix' the website temporarily by resetting the server twice (resetting it once does not work) using the following commands. NB: the 'reload' option does not work, I have to use restart twice. However, the error can reoccur sometime later. sudo /etc/init.d/apache2 restart sudo /etc/init.d/apache2 restart b) I have tried disabling suhosin by uninstalling php5-suhosin, but a php info page still shows "This server is protected with the Suhosin Patch 0.9.9.1". I have tried putting Suhosin into simulation mode by creating a file /etc/php5/apache2/conf.d/suhosin.ini containing: [suhosin] suhosin.simulation = On The php info page shows the suhosin.ini file in the list of "Additional .ini files parsed" but the php info page still shows "This server is protected with the Suhosin Patch 0.9.9.1" c) Increasing the PHP memory limit In /etc/php5/apache2/ : ; Maximum amount of memory a script may consume (128MB) ; http://php.net/memory-limit memory_limit = 512M d) Disabling all Wordpress plugins, and going back to the default theme. 5. Specific help needed I would very much like help in debugging what is going on here. I am not sure how to determine what processes are in the Apache error log which are exiting "[notice] child pid 1955 exit signal Floating point exception (8)", or what is causing them to exit. And whether suhosin is part of the problem (and how to disable it if it is). Thank you in advance for any advice or tips you can offer in helping me debug this.

    Read the article

  • Exchange 2003 mail non-delivery (NDR), spam activity? events 7002 & 7004

    - by HighTechGeek
    Windows Server 2003 Small Business Server SP2 Exchange Version 6.5 (Build 7638.2: Service Pack 2) This network has been neglected and has been having email problems for years and was on many blacklists. I was called in after the server eventually crashed... I got the server back up and running, but email problems persist. Outgoing mail delivery is sporadic. Sometimes the mail goes through, sometimes a delayed delivery report is generated after a day or more, and sometimes it seems to go through, but the recipient never receives it. Not sure if spammers are successfully using the server as a relay (see event entries below after turning on maximum SMTP logging)... User PCs infected with viruses and server was blacklisted on many sites (I used mxtoolbox.com) I have cleaned all the PCs and changed all passwords (including administrator) I have requested removal from all of the blacklists - most have removed the listing, some take more time. I have setup rDNS pointer records with the ISP (Comcast) - that was one reason for some of the blacklistings. I have tested that it's not an open relay using telnet as described here: www.amset.info/exchange/smtp-openrelay.asp I followed the advise of a Spamhaus & Microsoft article to enable maximum SMTP logging. http://www.spamhaus.org/faq/answers.lasso?section=isp%20spam%20issues#320 which directed me to Microsoft KB article 895853, specifically, the part 2/3 down titled: "If mail relay occurs from an account on an Exchange computer that is not configured as an open relay" . The Application Event Log is filling with this type of activity (Event ID 7002, 7002 & 3018 errors): Event Type: Error Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7004 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol error log for virtual server ID 1, connection #621. The remote host "212.52.84.180", responded to the SMTP command "rcpt" with "550 #5.1.0 Address rejected [email protected] ". The full command sent was "RCPT TO: ". This will probably cause the connection to fail. and this: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #620. The remote host "212.52.84.170", responded to the SMTP command "rcpt" with "452 Too many recipients received this hour ". The full command sent was "RCPT TO: ". This may cause the connection to fail. or a variant of: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 8:39:21 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #661. The remote host "82.57.200.133", responded to the SMTP command "rcpt" with "421 Service not available - too busy ". The full command sent was "RCPT TO: ". This may cause the connection to fail. also Event Type: Error Event Source: MSExchangeTransport Event Category: NDR Event ID: 3018 Date: 1/18/2011 Time: 9:49:37 AM User: N/A Computer: SERVER Description: A non-delivery report with a status code of 5.4.0 was generated for recipient rfc822;[email protected] (Message-ID ). Causes: This message indicates a DNS problem or an IP address configuration problem Solution: Check the DNS using nslookup or dnsq. Verify the IP address is in IPv4 literal format. Data: 0000: ef 02 04 c0 ï..À Any guidance and/or suggestions and/or tests to perform would be greatly appreciated.

    Read the article

  • CodePlex Daily Summary for Friday, February 19, 2010

    CodePlex Daily Summary for Friday, February 19, 2010New ProjectsApplication Management Library: Application Management makes your application life easier. It will automatic do memory management, handle and log unhandled exceptions, profiling y...Audio Service - Play Wave Files From Windows Service: This is a windows service that Check a registry key, when the key is updated with a new wave file path the service plays the wave file.Aviamodels: 3d drawing AviamodelsControl of payment proofs program for Greek citizens: This is a program that is used for Greek citizens who want to keep track of their payment proofs.Cover Creator: Cover Creator gives you the possibility to create and print CD covers. Content of CD is taken from http://www.freedb.org/ or can be added/modyfied ...DevBoard: DevBoard is a webbased scrum tool that helps developers/team get a clear overview of the project progress. It's developed in C# and silverlight.Flex AdventureWorks: The is mostly a skunk-works application to help me get acclimated to CodePlex. The long term goal is to integrate a Flex UI with the AdventureWor...GRE Wordlist: An intuitive and customizable word list for GRE aspirants. Developed in Java using a word list similar to Barron's.Indexer: A desktop file Index and Search tool which allows you to choose a list of folders to index, and then search on later. It is based on Lucene.net an...Project Management Office (PMO) for SharePoint: Sample web part for the Code Mastery event in Boston, February 11, 2010.Restart SQL Audit Policy and Job: Resolve SQL 2008 Audit Network Connectivity Issue.Rounded Corners / DIV Container: The RoundedDiv round corners container is a skin-able, CSS compliant UI control. Select which corners should be rounded, collapse and expand the c...Silverlight Google Search Application: The Silverlight Google Search Application uses Google Search API and behaves like Internet Search Application with option to preview desired page i...Weather Forecast Control: MyWeather forecast control pulls up to date weather forecast information from The Weather Channel for your website.New ReleasesApplication Management Library: ApplicationManagement v1.0: First ReleaseAudio Service - Play Wave Files From Windows Service: Audio Service v1.0: This is a working version of the Audio Service. Please use as you need to.AutoMapper: 1.0.1 for Silverlight 3.0 Alpha: AutoMapper for Silverlight 3.0. Features not supported: IDataReader mapping IListSource mapping All other features are supported.Buzz Dot Net: Buzz Dot Net v.1.10219: Buzz Dot Net Library (Parser & Objects) + WPF Example (using MVVM & Threading)Canvas VSDOC Intellisense: V 1.0.0.0a: This release contains two JavaScript files: canvas-utils.js (can be referenced in both runtime and development environment) canvas-vsdoc.js (must ...Control of payment proofs program for Greek citizens: Payment Proofs: source codeCourier: Beta 2: Added Rx Framework support and re-factored how message registration and un-registration works Blog post explaining the updates and re-factoring c...Cover Creator: Initial release: This is initial stable release. For now only in Polish language.Employee Scheduler: Employee Scheduler 2.2: Small Bug found. Small total hour calculation bug. See http://employeescheduler.codeplex.com/WorkItem/View.aspx?WorkItemId=6059 Extract the files...EnhSim: Release v1.9.7.1: Release v1.9.7.1Implemented Dislodged Foreign Object trinket Whispering Fanged Skull now also procs off Flame shock dots You can toggle bloodlust o...Extend SmallBasic: Teaching Extensions v.007: added SimpleSquareTest added Tortoise.Approve() for virtual proctor how to use virtual proctor: change the path in the proctor.txt file (located i...FolderSize: FolderSize.Win32.1.0.1.0: FolderSize.Win32.1.0.1.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...GLB Virtual Player Builder: v0.4.0 Beta: Allows for user to import and use archetypes for building players. The archetypes are contained in the file "archetypes.xml". This file is editab...Google Map WebPart from SharePoint List: GMap Stable Release: GMap Stable ReleaseHenge3D Physics Library for XNA: Henge3D Source (2010-02 R2): Fixed a build error related to an assembly attribute in XBOX 360 builds. Tweaked the controls in the sample when targeting the 360. Reduced the...Indexer: Beta Release 1: Just the initial/rough cut.NukeCS: NukeCS 5.2.3 Source Code: update version to 5.2.3ODOS: ODOS STABLE 1.5.0: Thank you for your patience while we develop this version. Not that much has been added, though. Just doing some sub-conscious stuff to make life...PoshBoard: PoshBoard 3.0 Beta 1: Welcome to the first beta release of PoshBoard 3.0 ! IMPORTANT WARNING : this release is absolutly not feature complete and is error-prone. Okay, ...Restart SQL Audit Policy and Job: Restart SQL 2008 Audit Policy and Job: This folder contains three pieces of source code: Server Audit Status (Started).xml - Import this on-schedule policy into your server's Policy-Ba...SAL- Self Artificial Learning: Artificial Learning 2AQV Working Proof Of Concept: This is the Simulation proof of concept version that comes after the 1aq version. AQ stands for Anwering Questions.SharePoint 2010 Word Automation: SP 2010 Word Automation - Workflow Actions 1.1: This release includes two new custom workflow activities for SharePoint designer Convert Folder Convert Library More information about these new...SharePoint Outlook Connector: Version 1.0.1.1: Exception Logging has been improved.Sharpy: Sharpy 1.2 Alpha: This is the third Sharpy release. A change has been made to allow overriding the master page from the controller. The release contains the single ...Silverlight Google Search Application: SL Google Search App Alpha: This is just a first alpha version of the application, as it looks like when I uploaded it to CodePlex. The application works, requires Silverlight...Starter Kit Mytrip.Mvc.Entity: Mytrip.Mvc.Entity 1.0 RC: EF Membership UserManager FileManager Localization Captcha ClientValidation Theme CrossBrowser VS 2010 RC MVC 2 RC db MSSQL2008thinktecture WSCF.blue: WSCF.blue V1 Update (1.0.6): This release is an update for WSCF.blue V1. Below are the bug fixes made since the V1.0.5 release: The data contract type filter was not including...TS3QueryLib.Net: TS3QueryLib.Net Version 0.18.13.0: Changelog Added overloads to all methods of QueryRunenr class handling permission tasks to allow passing of permission name instead of permissionid...Umbraco CMS: Umbraco 4.1 Beta 2: This is the second beta of Umbraco 4.1. Umbraco 4.1 is more advanced than ever, yet faster, lighter and simpler to use than ever. We, on behalf of...VCC: Latest build, v2.1.30218.0: Automatic drop of latest buildZack's Fiasco - Code Generated DAL: v1.2.4: Enhancements: SQL Server CRUD Stored Procedures added option for USE <db> added option to create or not create INSERT sprocs added option to cr...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)Image Resizer Powertoy Clone for WindowsASP.NETMicrosoft SQL Server Community & SamplesDotNetNuke® Community EditionMost Active ProjectsRawrSharpyDinnerNow.netBlogEngine.NETjQuery Library for SharePoint Web ServicesNB_Store - Free DotNetNuke Ecommerce Catalog Modulepatterns & practices – Enterprise LibraryPHPExcelFacebook Developer ToolkitFluent Ribbon Control Suite

    Read the article

  • Oracle Enterprise Manager 11g Application Management Suite for Oracle E-Business Suite Now Available

    - by chung.wu
    Oracle Enterprise Manager 11g Application Management Suite for Oracle E-Business Suite is now available. The management suite combines features that were available in the standalone Application Management Pack for Oracle E-Business Suite and Application Change Management Pack for Oracle E-Business Suite with Oracle's market leading real user monitoring and configuration management capabilities to provide the most complete solution for managing E-Business Suite applications. The features that were available in the standalone management packs are now packaged into Oracle E-Business Suite Plug-in 4.0, which is now fully certified with Oracle Enterprise Manager 11g Grid Control. This latest plug-in extends Grid Control with E-Business Suite specific management capabilities and features enhanced change management support. In addition, this latest release of Application Management Suite for Oracle E-Business Suite also includes numerous real user monitoring improvements. General Enhancements This new release of Application Management Suite for Oracle E-Business Suite offers the following key capabilities: Oracle Enterprise Manager 11g Grid Control Support: All components of the management suite are certified with Oracle Enterprise Manager 11g Grid Control. Built-in Diagnostic Ability: This release has numerous major enhancements that provide the necessary intelligence to determine if the product has been installed and configured correctly. There are diagnostics for Discovery, Cloning, and User Monitoring that will validate if the appropriate patches, privileges, setups, and profile options have been configured. This feature improves the setup and configuration time to be up and operational. Lifecycle Automation Enhancements Application Management Suite for Oracle E-Business Suite provides a centralized view to monitor and orchestrate changes (both functional and technical) across multiple Oracle E-Business Suite systems. In this latest release, it provides even more control and flexibility in managing Oracle E-Business Suite changes.Change Management: Built-in Diagnostic Ability: This latest release has numerous major enhancements that provide the necessary intelligence to determine if the product has been installed and configured correctly. There are diagnostics for Customization Manager, Patch Manager, and Setup Manager that will validate if the appropriate patches, privileges, setups, and profile options have been configured. Enhancing the setup time and configuration time to be up and operational. Customization Manager: Multi-Node Custom Application Registration: This feature automates the process of registering and validating custom products/applications on every node in a multi-node EBS system. Public/Private File Source Mappings and E-Business Suite Mappings: File Source Mappings & E-Business Suite Mappings can be created and marked as public or private. Only the creator/owner can define/edit his/her own mappings. Users can use public mappings, but cannot edit or change settings. Test Checkout Command for Versions: This feature allows you to test/verify checkout commands at the version level within the File Source Mapping page. Prerequisite Patch Validation: You can specify prerequisite patches for Customization packages and for Release 12 Oracle E-Business Suite packages. Destination Path Population: You can now automatically populate the Destination Path for common file types during package construction. OAF File Type Support: Ability to package Oracle Application Framework (OAF) customizations and deploy them across multiple Oracle E-Business Suite instances. Extended PLL Support: Ability to distinguish between different types of PLLs (that is, Report and Forms PLL files). Providing better granularity when managing PLL objects. Enhanced Standard Checker: Provides greater and more comprehensive list of coding standards that are verified during the package build process (for example, File Driver exceptions, Java checks, XML checks, SQL checks, etc.) HTML Package Readme: The package Readme is in HTML format and includes the file listing. Advanced Package Search Capabilities: The ability to utilize more criteria within the advanced search package (that is, Public, Last Updated by, Files Source Mapping, and E-Business Suite Mapping). Enhanced Package Build Notifications: More detailed information on the results of a package build process. Better, more detailed troubleshooting guidance in the event of build failures. Patch Manager:Staged Patches: Ability to run Patch Manager with no external internet access. Customer can download Oracle E-Business Suite patches into a shared location for Patch Manager to access and apply. Supports highly secured production environments that prohibit external internet connections. Support for Superseded Patches: Automatic check for superseded patches. Allows users to easily add superseded patches into the Patch Run. More comprehensive and correct Patch Runs. Removes many manual and laborious tasks, frees up Apps DBAs for higher value-added tasks. Automatic Primary Node Identification: Users can now specify which is the "primary node" (that is, which node hosts the Shared APPL_TOP) during the Patch Run interview process, available for Release 12 only. Setup Manager:Preview Extract Results: Ability to execute an extract in "proof mode", and examine the query results, to determine accuracy. Used in conjunction with the "where" clause in Advanced Filtering. This feature can provide better and more accurate fine tuning of extracts. Use Uploaded Extracts in New Projects: Ability to incorporate uploaded extracts in new projects via new LOV fields in package construction. Leverages the Setup Manager repository to access extracts that have been uploaded. Allows customer to reuse uploaded extracts to provision new instances. Re-use Existing (that is, historical) Extracts in New Projects: Ability to incorporate existing extracts in new projects via new LOV fields in package construction. Leverages the Setup Manager repository to access point-in-time extracts (snapshots) of configuration data. Allows customer to reuse existing extracts to provision new instances. Allows comparative historical reporting of identical APIs, executed at different times. Support for BR100 formats: Setup Manager can now automatically produce reports in the BR100 format. Native support for industry standard formats. Concurrent Manager API Support: General Foundation now provides an API for management of "Concurrent Manager" configuration data. Ability to migrate Concurrent Managers from one instance to another. Complete the setup once and never again; no need to redefine the Concurrent Managers. User Experience Management Enhancements Application Management Suite for Oracle E-Business Suite includes comprehensive capabilities for user experience management, supporting both real user and synthetic transaction based user monitoring techniques. This latest release of the management suite include numerous improvements in real user monitoring support. KPI Reporting: Configurable decimal precision for reporting of KPI and SLA values. By default, this is two decimal places. KPI numerator and denominator information. It is now possible to view KPI numerator and denominator information, and to have it available for export. Content Messages Processing: The application content message facility has been extended to distinguish between notifications and errors. In addition, it is now possible to specify matching rules that can be used to refine a selected content message specification. Note this is only available for XPath-based (not literal) message contents. Data Export: The Enriched data export facility has been significantly enhanced to provide improved performance and accessibility. Data is no longer stored within XML-based files, but is now stored within the Reporter database. However, it is possible to configure an alternative database for its storage. Access to the export data is through SQL. With this enhancement, it is now more easy than ever to use tools such as Oracle Business Intelligence Enterprise Edition to analyze correlated data collected from real user monitoring and business data sources. SNMP Traps for System Events: Previously, the SNMP notification facility was only available for KPI alerting. It has now been extended to support the generation of SNMP traps for system events, to provide external health monitoring of the RUEI system processes. Performance Improvements: Enhanced dashboard performance. The dashboard facility has been enhanced to support the parallel loading of items. In the case of dashboards containing large numbers of items, this can result in a significant performance improvement. Initial period selection within Data Browser and reports. The User Preferences facility has been extended to allow you to specify the initial period selection when first entering the Data Browser or reports facility. The default is the last hour. Performance improvement when querying the all sessions group. Technical Prerequisites, Download and Installation Instructions The Linux version of the plug-in is available for immediate download from Oracle Technology Network or Oracle eDelivery. For specific information regarding technical prerequisites, product download and installation, please refer to My Oracle Support note 1224313.1. The following certifications are in progress: * Oracle Solaris on SPARC (64-bit) (9, 10) * HP-UX Itanium (11.23, 11.31) * HP-UX PA-RISC (64-bit) (11.23, 11.31) * IBM AIX on Power Systems (64-bit) (5.3, 6.1)

    Read the article

  • Install Ubuntu Netbook Edition with Wubi Installer

    - by Matthew Guay
    Ubuntu is one of the most popular versions of Linux, and their Netbook Remix edition is especially attractive for netbook owners.  Here we’ll look at how you can easily try out Ubuntu on your netbook without a CD/DVD drive. Netbooks, along with the growing number of thin, full powered laptops, lack a CD/DVD drive.  Installing software isn’t much of a problem since most programs, whether free or for-pay, are available for download.  Operating systems, however, are usually installed from a disk.  You can easily install Windows 7 from a flash drive with our tutorial, but installing Ubuntu from a USB flash drive is more complicated.  However, using Wubi, a Windows installer for Ubuntu, you can easily install it directly on your netbook and even uninstall it with only a few clicks. Getting Started Download and run the Wubi installer for Ubuntu (link below).  In the installer, select the drive you where you wish to install Ubuntu, the size of the installation (this is the amount dedicated to Ubuntu; under 20Gb should be fine), language, username, and desired password.  Also, from the Desktop environment menu, select Ubuntu Netbook to install the netbook edition.  Click Install when your settings are correct. Wubi will automatically download the selected version of Ubuntu and install it on your computer. Windows Firewall may ask if you want to unblock Wubi; select your network and click Allow access. The download will take around an hour on broadband, depending on your internet connection speed.  Once the download is completed, it will automatically install to your computer.  If you’d prefer to have everything downloaded before you start the install, download the ISO of Ubuntu Netbook edition (link below) and save it in the same folder as Wubi. Then, when you run Wubi, select the netbook edition as before and click Install.  Wubi will verify that your download is valid, and will then proceed to install from the downloaded ISO.  This install will only take about 10 minutes. Once the install is finished you will be asked to reboot your computer.  Save anything else you’re working on, and then reboot to finish setting up Ubuntu on your netbook. When your computer reboots, select Ubuntu at the boot screen.  Wubi leaves the default OS as Windows 7, so if you don’t select anything it will boot into Windows 7 after a few seconds. Ubuntu will automatically finish the install when you boot into it the first time.  This took about 12 minutes in our test. When the setup is finished, your netbook will reboot one more time.  Remember again to select Ubuntu at the boot screen.  You’ll then see a second boot screen; press your Enter key to select the default.   Ubuntu only took less than a minute to boot in our test.  When you see the login screen, select your name and enter your password you setup in Wubi.  Now you’re ready to start exploring Ubuntu Netbook Remix. Using Ubuntu Netbook Remix Ubuntu Netbook Remix offers a simple, full-screen interface to take the best advantage of netbooks’ small screens.  Pre-installed applications are displayed in the application launcher, and are organized by category.  Click once to open an application. The first screen on the application launcher shows your favorite programs.  If you’d like to add another application to the favorites pane, click the plus sign beside its icon. Your files from Windows are still accessible from Ubuntu Netbook Remix.  From the home screen, select Files & Folders on the left menu, and then click the icon that says something like 100GB Filesystem under the Volumes section. Now you’ll be able to see all of your files from Windows.  Your user files such as documents, music, and pictures should be located in Documents and Settings in a folder with your user name. You can also easily install a variety of free applications via the Software Installer. Connecting to the internet is also easy, as Ubuntu Netbook Remix automatically recognized the WiFi adaptor on our test netbook, a Samsung N150.  To connect to a wireless network, click the wireless icon on the top right of the screen and select the network’s name from the list. And, if you’d like to customize your screen, right-click on the application launcher and select Change desktop background. Choose a background picture you’d like. Now you’ll see it through your application launcher.  Nice! Most applications are opened full-screen.  You can close them by clicking the x on the right of the program’s name. You can also switch to other applications from their icons on the top left.  Open the home screen by clicking the Ubuntu logo in the far left. Changing Boot Options By default, Wubi will leave Windows as the default operating system, and will give you 10 seconds at boot to choose to boot into Ubuntu.  To change this, boot into Windows and enter Advanced system settings in your start menu search. In this dialog, click Settings under Startup and Recovery. From this dialog, you can select the default operating system and the time to display list of operating systems.  You can enter a lower number to make the boot screen appear for less time. And if you’d rather make Ubuntu the default operating system, select it from the drop-down list.   Uninstalling Ubuntu Netbook Remix If you decide you don’t want to keep Ubuntu Netbook Remix on your computer, you can uninstall it just like you uninstall any normal application.  Boot your computer into Windows, open Control Panel, click Uninstall a Program, and enter ubuntu in the search box.  Select it, and click Uninstall. Click Uninstall at the prompt.  Ubuntu uninstalls very quickly, and removes the entry from the bootloader as well, so your computer is just like it was before you installed it.   Conclusion Ubuntu Netbook Remix offers an attractive Linux interface for netbooks.  We enjoyed trying it out, and found it much more user-friendly than most Linux distros.  And with the Wubi installer, you can install it risk-free and try it out on your netbook.  Or, if you’d like to try out another alternate netbook operating system, check out our article on Jolicloud, another new OS for netbooks. Links Download Wubi Installer for Windows Download Ubuntu Netbook Edition Similar Articles Productive Geek Tips Easily Install Ubuntu Linux with Windows Using the Wubi InstallerInstall VMware Tools on Ubuntu Edgy EftHow to install Spotify in Ubuntu 9.10 using WineInstalling PHP5 and Apache on UbuntuInstalling PHP4 and Apache on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Explorer++ is a Worthy Windows Explorer Alternative Error Goblin Explains Windows Error Codes Twelve must-have Google Chrome plugins Cool Looking Skins for Windows Media Player 12 Move the Mouse Pointer With Your Face Movement Using eViacam Boot Windows Faster With Boot Performance Diagnostics

    Read the article

  • Twitter traffic might not be what it seems

    - by Piet
    Are you using bit.ly stats to measure interest in the links you post on twitter? I’ve been hearing for a while about people claiming to get the majority of their traffic originating from twitter these days. Now, I’ve been playing with the twitter ruby gem recently, doing various experiments which I’ll not go into detail here because they could be regarded as spamming… if I’d conduct them on a large scale, that is. It’s scary to see people actually engaging with @replies crafted with some regular expressions and eliza-like trickery on status updates found using the twitter api. I’m wondering how Twitter is going to contain the coming spam-flood. When posting links I used bit.ly as url shortener, since this one seems to be the de-facto standard on twitter. A nice thing about bit.ly is that it shows some basic stats about the redirects it performs for your shortened links. To my surprise, most links posted almost immediately resulted in several visitors. Now, seeing that I was posting the links together with some information concerning what the link is about, I concluded that the people who were actually clicking the links should be very targeted visitors. This felt a bit like free adwords, and I suddenly started to understand why everyone was raving about getting traffic from twitter. How wrong I was! (and I think several 1000 online marketers with me) On the destination site I used a traffic logging solution that works by including a little javascript snippet in your pages. It seemed that somehow all visitors disappeared after the bit.ly redirect and before getting to the site, because I was hardly seeing any visitors there. So I started investigating what was happening: by looking at the logfiles of the destination site, and by making my own ’shortened’ urls by doing redirects using a very short domain name I own. This way, I could check the apache access_log before the redirects. Most user agents turned out to be bots without a doubt. Here’s an excerpt of user-agents awk’ed from apache’s access_log for a time period of about one hour, right after posting some links: AideRSS 2.0 (postrank.com) Java/1.6.0_13 Java/1.6.0_14 libwww-perl/5.816 MLBot (www.metadatalabs.com/mlbot) Mozilla/4.0 (compatible;MSIE 5.01; Windows -NT 5.0 - real-url.org) Mozilla/5.0 (compatible; Twitturls; +http://twitturls.com) Mozilla/5.0 (compatible; Viralheat Bot/1.0; +http://www.viralheat.com/) Mozilla/5.0 (Danger hiptop 4.6; U; rv:1.7.12) Gecko/20050920 Mozilla/5.0 (X11; U; Linux i686; en-us; rv:1.9.0.2) Gecko/2008092313 Ubuntu/9.04 (jaunty) Firefox/3.5 OpenCalaisSemanticProxy PycURL/7.18.2 PycURL/7.19.3 Python-urllib/1.17 Twingly Recon twitmatic Twitturly / v0.6 Wget/1.10.2 (Red Hat modified) Wget/1.11.1 (Red Hat modified) Of the few user-agents that seem ‘real’ at first, half are originating from an ip-address used by Amazon EC2. And I doubt people are setting op proxies on there. Oh yeah, Googlebot (the real deal, from a legit google owned address) is sucking up posted links like fresh oysters. I guess google is trying to make sure in advance to never be beaten by twitter in the ‘realtime search’ department. Actually, I think it’d be almost stupid NOT to post any new pages/posts/websites on Twitter, it must be one of the fastest ways to get a Googlebot visit. Same experiment with a real, established twitter account Now, because I was posting the url’s either as ’status’ messages or directed @people, on a test-account with hardly any (human) followers, I checked again using the twitter accounts from a commercial site I’m involved with. These accounts all have between 500 and 1000 targeted (I think) followers. I checked the destination access_logs and also added ‘my’ redirect after the bit.ly redirect: same results, although seemingly a bit higher real visitor/bot ratio. Btw: one of these account was ‘punished’ with a 1 week lock recently because the same (1 one!) status update was sent that was sent right before using another account. They got an email explaining the lock because the account didn’t act according to their TOS. I can’t find anything in their TOS about it, can you? I don’t think Twitter is on the right track punishing a legit account, knowing the trickery I had been doing with it’s api went totally unpunished. I might be wrong though, I often am. On the other hand: this commercial site reported targeted traffic and actual signups from visitors coming from Twitter. The ones that are really real visitors are also very targeted. I’m just not sure if the amount of work involved could hold up against an adwords campaign. Reposting the same link over and over again helps On thing I noticed: It helps to keep on reposting the same links with regular intervals. I guess most people only look at their first page when checking out recent posts of the ones they’re following, or don’t look too far back when performing a search. Now, this probably isn’t according to the twitter TOS. Actually, it might be spamming but no-one is obligated to follow anyone else of course. This way, I was getting more real visitors and less bots. To my surprise (when my programmer’s hat is on) there were still repeated visits from the same bots coming from the same ip-addresses. Did they expect to find something else when visiting for a 2nd or 3rd time? (actually,this gave me an idea: you can’t change a link once it’s posted, but you can change where it redirects to) Most bots were smart enough not to follow the same link again though. Are you successful in getting real visitors from Twitter? Are you only relying on bit.ly to provide traffic stats?

    Read the article

  • 2 Days of Share &amp; Point

    - by Mark Rackley
    Groovy man… SharePoint Saturday Ozarks is back for 2010, bigger and better than before. Join us for a far out time and learn more about SharePoint in one day than you could in a year from the man… Yes! SharePoint Saturday Ozarks is back! SharePoint Saturday Ozarks is the largest SharePoint conference in Arkansas, Southern Missouri, and the very north east tip of Oklahoma. Last year we had a great turn out with 20 speakers, 5 MVPs, and attendees coming from Arkansas, Texas, Oklahoma, Missouri, Kansas, Nebraska, Indiana, Ohio, Alabama, Michigan, and Washington. Hey Man… what’s SharePoint Saturday anyway? Sounds like a conspiracy man… Not to worry, SharePoint Saturday is not an arm of the government bent on mind control or any attempt what-so-ever to bring you down man. SharePoint Saturday is grass roots effort started by Michael Lotter (http://www.sharepointsaturday.org/pages/about.aspx). It is a FREE one day event where the best SharePoint speakers gather to present their love, hatred, and frustrations of SharePoint to those lucky individuals who attend. Lessons are learned, contacts are made, prizes are won, food is eaten, assorted beverages are consumed until wee hours of the morning. SharePoint Saturday started with just a few sporadic one day events here and there. However, over the past year SharePoint Saturday has exploded and it’s hard to find a weekend where there is NOT a SharePoint Saturday event happing in some corner of the globe. There are even occasions where there are two SharePoint Saturdays on the same day! Many people are pleasantly surprised at the caliber of speakers at these SharePoint Saturday events. For the most part, these speakers are more eloquent, practiced, and practical than those speakers you find at the major multi-day conferences. These guys aren’t even paid to speak.. they do it out of love man… SharePoint Saturday Ozarks 2009 Alumni We had a star studded cast last year with many returning this year! Just check out the fun that they had… John Ferringer – Admin rockstar… I can still sense the awesomeness   SharePoint poster children Mike Watson & Laura Rogers     Lori Gowin spreading the SharePoint Love Eric Shupps is a little bit country and a little bit rock and roll       Cathy Dew, Sean McDonough, and JD Wade relaxing between gigs Actually, you can see real photos from last year’s SharePoint Saturday ozarks here:  picasaweb.google.com/mrackley/SharePointSaturdayOzarks#    What’s new for SharePoint Saturday Ozarks 2010 SharePoint Saturday Ozarks 2010 will totally blow your mind man. We’re getting the band back to together with many returning speakers and few new faces. Joel Oleson will be speaking this year, maybe he’ll grace us with his song stylings. Sadly, once again, Andrew Connell will not be able to attend SharePoint Saturday Ozarks, however he did feel the need to show his support in his own way. Prizes this year currently include books, software, a Zune HD, and much more! Wait Man… You said 2 days? I thought it was a one day event? Correct you are my herbal smelling friend… SharePoint Saturday Ozarks 2010 will spread the love an additional day this year. The first day will be all about the SharePoint love, on day 2 we will be taking a leisurely float down the Buffalo National River for those interested in a truly unique experience (no banjos allowed please).   Here are the details: WHAT 4 – 5 hour float down the Buffalo National River WHEN & WHERE Sunday June 13th. We will be leaving at 10am from the Parking Lot of: Gordon’s Motel & Canoe Rental Old Highway 7 Jasper, AR 72641 (870) 446-5252 Jasper is about 30 minutes south of Harrison, AR on Highway 7 South. You are responsible for bumming a ride to/from Gordon’s Motel, but they will be shuttling us to/from the river and providing canoes and a boxed lunch. WHAT ELSE? The float trip is dependent on the weather of course, we won’t be floating down the river in a thunderstorm, however I planned SPS Ozarks around a time of year ideal for floating. We aren’t talking class 5 rapids here, you don’t need any real skill, but you need to be okay with possibly tipping your canoe over once or twice. You can bring your own assorted beverages with you, but glass containers are not allowed on the river. I suggest a small cooler with extra snacks and drinks. Also bring clothing you can get wet in (these SharePoint people can get ornery). HOW DO I SIGN UP? When you register for SharePoint Saturday Ozarks, you will have the option to also sign up for the float trip. Seats are limited though! If you do not intend to go, please do not take someone else’s place.  The cost for the float trip will be about $35 dollars per person (which you are responsible for unless we find a sponsor). The price includes shuttle to/from river, canoe, life jackets, paddles, and boxed lunch. Far out man… how do I register??? You can register for SharePoint Saturday Ozarks by going to http://spsozarks.eventbrite.com/ We are limited to 200 people for the conference and 50 people for the float trip, so register today before we are sold out. Lodging for SharePoint Saturday Ozarks will once again take place at the Hotel Seville: Annex Suites are available for $103.20 This is So Groovy.. How can I help? I’m glad you asked! We are still looking for a few sponsors and one or two more speakers. If you are interested please let me know!  You can find out more information at http://www.sharepointsaturday.org/ozarks Hey… wait a minute…. what exactly IS SharePoint man??? Come to SharePoint Saturday Ozarks and find out!!  See you guys there!

    Read the article

< Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >