Search Results

Search found 2489 results on 100 pages for 'hp laserjet'.

Page 11/100 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

  • HP Pavilion tx2000 - Wifi adapter no longer works after moving from 12.04 to a 12.10 clean install

    - by Marek L.
    I have a HP Pavilion tx2000 that I have been running Ubuntu 12.04 on for a couple of months without any problems (wifi worked great) until yesterday when my hard drive failed. I replaced the hard drive and decided to install Ubuntu 12.10. Unlike 12.04, the wifi did not work after the installation finished and all the updates where installed (over Ethernet). The network drop down in the top right didn't even show a wireless option. I Googled about for a bit and found some solutions that seemed like they might work. Unfortunately they did not. Here is what I tried: sudo apt-get remove bcmwl-kernel-source sudo apt-get install b43-fwcutter sudo apt-get install firmware-b43-lpphy-installer Restart the computer. And the wifi still didn't work. At which point I panicked a bit and tried to undo the previous commands by running: sudo apt-get remove b43-fwcutter firmware-b43-lpphy-installer sudo apt-get install bcmwl-kernel-source Restart the computer. The wifi still doesn't work. This is where I stopped because I have no idea what I am doing and don't want to mess something up. The network drop down still doesn't show a wireless option and the hardware wifi switch on the laptop is amber (it turns blue when the wifi is on). Using the hardware switch does not change the color. Output from: sudo lspci ... 08:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01) ... Output from: sudo lshw -class network *-network UNCLAIMED description: Network controller product: BCM4322 802.11a/b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1100000-d1103fff ... Output from: sudo rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes UPDATE: After writing up this question tried the following command: sudo rfkill unblock all At first it didn't do anything but after running it about four times, sudo rfkill list all now returns: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no But the network menu still does not have a wireless option and the hardware switch still glows amber. Pushing the hardware switch turns the hard block back on and I have to run sudo rfkill unblock all multiple times again to turn it off. Any help is appreciated! Update 2: Full output from sudo lspci -nn: 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604] 00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] 00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration [1022:1300] (rev 40) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Address Map [1022:1301] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller [1022:1302] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control [1022:1303] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Link Control [1022:1304] 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] [1002:9612] 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)

    Read the article

  • Unable to retrieve information form HP-UX pst_status object

    - by bogertron
    I am attempting to get process information by using the HP-UX C/C++ library. After scouring the internet, I have discovered that HP-UX has the pstat.h header file which allows programmers to retrieve the process information. After attempting to understand code from the internet hp website, I attempted to create a little test sample to comprehend what the code does. I attempted to use example 3, however, I ran into several issues. The first issue came when I attempted to execute the following line of code: (void)printf("pid is %d, command is %s\n", pst[i].pst_pid, pst[i].pst_ucomm); When I attempted to print the string, I hit a memory fault. So I decided to attempt to see what the string is and came up with the following: #include <sys/param.h> #include <sys/pstat.h> #include <sys/unistd.h> #include <string.h> int main(int argc, char** argv) { #define BURST ((size_t)10) struct pst_status pst[BURST]; int i, count; int idx = 0; /* index within the context */ int index = 0; /* loop until count == 0, will occur all have been returned */ while ((count=pstat_getproc(pst, sizeof(pst[0]),BURST,idx))>0) { index = 0; printf("index: %d", index); /* got count (max of BURST) this time. process them */ while (pst[i].pst_ucomm[index] != '\0') { printf("%c", pst[i].pst_ucomm[index]); index++; } printf("\n"); for (i = 0; i < count; i++) { printf("pid is %d, command is \n", pst[i].pst_pid); } /* * now go back and do it again, using the next index after * the current 'burst' */ idx = pst[count-1].pst_idx + 1; } if (count == -1) perror("pstat_getproc()"); #undef BURST } Unfortunately, what happens is that I get the first process printed, then pid is 2, command is pid is 2, command is pid is 2, command is... I know that I must be doing something foolish since my C/C++ skills are not that great, but I cannot figure out what the issue is since the code is largely copied from the hp website. So here's the question(s) for clarity: 1. Why can't printf("%s", pst[i].pst_ucomm); handle strings? 2. Why can't I iterate over the processes in the system? Any help is greatly appreciated.

    Read the article

  • Access Officejet Pro L7590 memory card reader

    - by luri
    I can't manage to access my printer's memory card reader in Nautilus. I can just access it with hp-unload. Here's a sample output from this command: lubuntu@L-X6:~$ hp-unload hp:/net/Officejet_Pro_L7500?zc=HP065193 HP Linux Imaging and Printing System (ver. 3.10.6) Photo Card Access Utility ver. 3.3 Copyright (c) 2001-9 Hewlett-Packard Development Company, LP This software comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to distribute it under certain conditions. See COPYING file for more details. Using device: hp:/net/Officejet_Pro_L7500?zc=HP065193 |error: Photo card write failed (Card may be write protected) / Photocard on device hp:/net/Officejet_Pro_L7500?zc=HP065193 mounted DO NOT REMOVE PHOTO CARD UNTIL YOU EXIT THIS PROGRAM warning: Photo card is write protected. Type 'help' for a list of commands. Type 'exit' to quit. pcard: / > ls \ Name Size Type dcim/ directory eos_digi.tal 0 B unknown/unknown 1 files, 0 B pcard: / > cd dcim |pcard: /dcim > ls | Name Size Type . directory .. directory 100eos5d/ directory 267canon/ directory 270canon/ directory 271canon/ directory 272canon/ directory 0 files, 0 B pcard: /dcim > cd 272canon -pcard: /dcim/272canon > ls \ Name Size Type . directory .. directory _mg_7201.jpg 3.1 MB image/jpeg ...........(some more files)................. _mg_7281.jpg 2.5 MB image/jpeg _mg_7282.jpg 2.5 MB image/jpeg 82 files, 241.6 MB (253377883) How can I acess it from nautilus or mount it as a filesystem? Note that this is similar to this other question: Can't get HP Officejet 6500 card reader to work. but actually there seemed to be no supported device here, while in my case I manage to access the memory card from hp-unload.

    Read the article

  • HP ACU shows parity initialization failed (with screenshot)

    - by lbanz
    I put in a new drive due to a hard drive failure. When the rebuild got to 100%, the controller fails and I need to reboot the server to bring it online. I had to do this about three times and it eventually finished rebuilding. But I found that it says parity initialization status failed. I've left it for a few hours but it didn't seem to reinitialize. Then I ran the insight online diagnostic tools and it reported the disk that I put in reached read/write error threshold. So I'm beginning to think that the brand new disk I put in is faulty. Before I put in the disk, the parity initialization was at a finished state. Should I replace the new disk I put in? I'm very worried as I think the parity is broken. Or is there a way to kick start the initialization process?

    Read the article

  • HP 6350b Laptop is my battery really dead or is it a software problem

    - by Datapimp23
    I installed windows 7 and noticed that the battery status was "plugged in, not charging". I tried unplugging the battery, uninstalling the microsoft ACPI compliant Control Method, updating bios,windows. All to no avail. at first I tought it was related to windows 7 because it's a brand new laptop. But I also tested with a knoppix live cd, and there the output of acpi -V is this Battery 0: Unknown, 0% What else can I test to figure out what's going on.

    Read the article

  • Laptop choice for development: MacBook Pro 17 vs Dell Studio XPS 16 vs HP Envy 15

    - by Shalan
    Hey! First things first - let me state that I am not intending to play games on this - I have narrowed down to these 3 purely based on specs and its individual brand reliability in the market. I intend to primarily use: Visual Studio 2008 Pro a lot (develop and deploy on Windows platforms) SQL Server 2005 Oracle 10g Adobe Photoshop CS4 Microsoft Expression Studio Google Sketchup I currently use a desktop PC (Core2Duo 2.66Ghz with 3GB DDRII memory) running Vista Business 32-bit - and I have to admit that, especially for Visual Studio, its quite sluggish to a point where it affects productivity. Furthermore, I intend to only use the notebook on a table - with a cooled surface, like granite :) - so I would appreciate people's input with regard to heat issues. Im aware that the Dell's primary exhaust gets blocked by the lid when open, but some reviews don't seem to place extraordinary emphasis on heat issues resulting from this. My options for the Dell/Alienware: Core i7 720QM 4GB DDRIII memory ATI mobility 3670 (512) 128GB Solid State Drive 16-inch Full HD RGB-LED LCD display (1080p) 3-year next-business-day support My configuration for the Apple MBP: Core2Duo 2.8Ghz (Im assuming the T9600) 4GB DDRIII memory 128GB Solid State Drive standard 1 year support The one advantage I think of with the MBP is that I can have the addition of OSX (though Im unsure what I would use it for, but purely to play around with a much-boasted-about OS) What are your thoughts on this, especially regarding build-quality, heat, performance and battery-life? Much thanks! ~shalan

    Read the article

  • HP Pavilion dv6000 graphics issue

    - by Tony
    A few days ago my laptop seized up on me while I was playing a game. When I restarted the computer, it sent me back to 640x480 resolution with 16 colors (clearly a graphical issue). In device manager, it shows an error, stating "Windows has stopped this device because it has reported problems. (Code 43)" regarding the video card. Upon removing and re-installing the drivers using both Windows Update and my own searching through nvidia's site, it's given me zero results. For kicks, I ran my antivirus (you never know!) and registry cleaner to see if anything would turn up. The antivirus found nothing, but CCleaner found 27 registry errors all dealing with my video card. What could be the cause of this, and what course of action would you recommend in this situation? Thanks in advance for the help! OS: Windows 7 Professional GPU: nvidia GeForce 8400M GS

    Read the article

  • HP ProCurve Port Mode Configuration Question

    - by SvrGuy
    We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

    Read the article

  • HP DL380 RAID5 Mistake

    - by Eddy
    I had drives fail in both logical drives on a server. When I replaced failed 146GB drive in Raid 5 array with four (4) 146GB drives. On reboot the Smart Array controller asked if I wanted to accept data loss. Guess mistake to choose yes. Can't seem to find a way to get system to repair RAID5 but it seems to want to just create a new partition. Is there anyway I can go back and get the system to restore the data from other three drives now that I said accept data loss?

    Read the article

  • HP DL580 G5 Hyper-V networking problem

    - by mr-perfect
    Hi I have installed the hyper-v role on a DL580 G5 cluster. The host operating system is a server 2008 x64 patched to the maximum. Everything has gone fine, but if I install a guest operating system, actually a windows server 2008 x64 I can't reach the network from it. It send many packets, but don't received any, so I can't ping the external network as well. I have installed the latest drivers to the server and unintalled the network configuration utility from the physical server, but no luck. I added a legacy adapter to the guest binded to the same phisycal adapter on the host machine but it can't help Any idea welcome...

    Read the article

  • HP OfficeJet 5600 w/ Dlink DPR1260 not printing except from Notepad

    - by joelarson
    I have an OfficeJet5600 attached to a Dlink DPR1260 wireless print router. It has worked great for a long time. Today we had a power outage and the thing was inaccessible. I reset the DPR1260 and reinstalled drivers and soforth. I can now print from Notepad, but not from any Office programs, IE, or Chrome. I have toggled on and off many settings such as spooling/not spooling, etc. Nothing has helped. Any ideas? I have Windows Vista.

    Read the article

  • HP Pavilion DV6 doesn't recognize wireless networks

    - by Mike N.
    Okay so about a few weeks after I got my laptop the wifi would connect and disconnect, off and on. And every time I troubleshoot it, a message comes up saying there's a network cable not properly plugged in or broken... It's been doing this for about a year and I usually just tap the bottom of the laptop or something and the wifi connects again but now it refuses to turn back on, how do I fix this?

    Read the article

  • HP ProLiant Smart Array "lock up" code 0x11

    - by ewwhite
    I've a ProLiant DL580 G7 server that experienced a storage subsystem failure during production. The system appeared available and responded to pings, but all I/O access stalled (the system load must have been 100+). The ASR did not trigger at the specified watchdog timeout. I had to force a reboot from the ILO. During POST, I received the following error: A controller failure event occurred prior to this power-up. (Previous lock up code = 0x11) I haven't pulled the ADU report yet, but I'm curious as to what this error actually means. I was not responsible for the the installation, but can see that the firmware is very old. But if there's anything else I should know about the error, I'd like to know for the post-mortem report. edit - I should add that the server had 95 days of uptime prior to the lock up.

    Read the article

  • HP ProCurve Port Mode Configuration Question Mark 2

    - by SvrGuy
    We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. From the CLI when I try to set 1000-full I get the following error: Value 1000-full is not applicable to port 39 (or whatever port I try) The exact commands I have entered are: config interface 39 speed-duplex 1000-full BTW: speed-duplex auto-1000 works ( I also tried full-1000 and that did not work either) How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

    Read the article

  • Extend RAID 1 (HP SmartArray P410i) running Linux

    - by Oliver
    I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

    Read the article

  • HP Mini 210 -> Touchpad doesn't work on Ubuntu

    - by iftrue
    Specifically, I can neither click nor right-click by using the the touch pad. The touch pad has buttons built-into it, which is why it probably doesn't work by default. If you followed my previous post, I switched to ubuntu to get wireless working on this netbook (which it does, yay), but now I can't right click. Lovely. Any suggesions? I installed gsynaptics and enabled SHMConfig, but that didn't do any good.

    Read the article

  • HP ProLiant DL320e G8 v2 - USB2.0 during POST

    - by user3513346
    Initially my USB2.0 ports were working during POST (and boot). However, now they appear not to be. I first noticed this when I could not access the RBSU by pressing F9 during POST. Then found that I couldn't boot from USB either (I was able to do both of these initially). When performing the boot via iLo remote console I can access all of the setups (i.e., all of the F(X)'s) and can boot virtual media from a 'removable drive'. Keyboard works fine once the OS is booted. Not really sure what to try here. Any advice would be greatly appreciated. Thanks. Nick.

    Read the article

  • Sparing level on HP EVA 4000

    - by Samuel
    One of the disks of our EVA4000 died today. This diskgroup (all volumes vraid5 with sparing level 1 and almost no space left for more volumes, 1TiB drives) is being rebuilt with "spare space" right now, and it will take at least 15 hours to do the leveling/rebuilding. We can't get a new disk until Friday. So, the question is, what would happen if another disk dies before the leveling completes? Would we lose data? And after that, how many aditional disks could die before losing data? 1 or 2? In "usual" RAID, we would be vulnerable to data loss while the rebuild takes place, but in this case the space reserved for sparing is two times the size of the bigger disk, so at the very least the effect should be the same of having two spares. Thanks in advance. Update: I have found some interesting threads about this question but still can't answer to this question, so I'm starting a bounty. http://blog.thestoragearchitect.com/2008/10/27/understanding-eva/ http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&url=http%3A%2F%2Fwww.experts-exchange.com%2FStorage%2FStorage_Technology%2FQ_25548177.html (Expert Exchange question from google).

    Read the article

  • How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

    - by vm370
    as you can see from my question, I have a VLAN configuration problem with a ProCurve3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different VLAN or the Default VLAN. I always get the message "config failed", which is not very helpful. When I try to do it over telnet, the router somehow partially crashes and somehow the utilization on all ports is at 100% and I can barely use the web ui. After a reboot everything is fine again, but the configuration was not changed... The traffic after this partial crash looks like a broadcast storm, however there are definitely no loops in the segment. I also updated to the latest stable firmware, but the problem persists. Thanks a lot in advance Br vm370

    Read the article

  • hp DL380 G4 won't boot with disk plugged into front USB

    - by Kev
    We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the BIOS (which is current, BTW) and never boot, even though the USB disks are not "bootable" per se. Our old drives did not exhibit this behaviour (so I don't think it's this type of issue that I've read about other servers.) The old drives were USB 2.0, but this shouldn't make a difference, AFAICT--the specs say all of the G4's USB ports are the same, 2.0, anyway, so I'm not sure how one port would handle a USB 3.0 device better than another. If we plug the new drives in one of the back slots, it boots fine. What's the cause? My concern is that the front USB port, and possibly the motherboard, might be starting to die. (We are experiencing other strange issues with them, or were initially, like intermittent file permissions errors despite wide-open ACL on these local drives, but some serverfault users have me convinced they may be coincidental software/security related issues.)

    Read the article

  • HP Media Smart remote access

    - by Coov
    I just purchased this box for home backups for my pc's and mac's. Everything works great accept for the remote access part. I can RD into the machine locally but I can't get to it from outside of my network. I've enabled port forwarding on my router but it doesn't seem to matter. I checked with Qwest and they don't block these ports so I'm at a loss. I do have Vonage in front of my router but I've taken it out and it didn't make a difference. I suspect I've made an error with my router setup. I'm a programmer and I'm playing in the world of the unknown here. I'm lost. Any suggestions?

    Read the article

  • HP Officejet 7410 AIO: Scanning/copying output is a solid black field

    - by William
    I recently tried to breathe some life back into an old Officejet 7410 for my parents. The printing is fine, but the scanning and the copying respectively produce images and copies that are mostly solid black, except for the first inch or so from the top of the original page. At first I thought this was a bulb problem, so I replaced it. Unfortunately, the problematic behavior is still there. I've tried resetting to factory defaults. Still no improvement. I don't think this is related to my OS or drivers, since the copying is also affected even when the connected computer is powered off. So... my question(s): What is the cause of this bad behavior? Given that, can my Officejet be repaired? If so, how? Thanks in advance.

    Read the article

  • Hp pavilion dv7 power button

    - by Danny B
    My power button is non responsive I am getting LED for charging. I've taken it apart before to change the dc jack and it was fine and a few months later it just powered off. I try to power back on and is goes to start up then shuts off. I just took it apart and came to find the ribbon cable connecting the power button/speakers cover is barely hanging on do I have to replace the whole thing or is there a way to replace the ribbon cable?

    Read the article

  • HP PAVILION NOTEBOOK PC DV6880 Blue Screen

    - by NaV
    Environment : Win-Vista 64 BIT Graphics Processor / Vendor NVIDIA GeForce 8400M GS Video Memory 256 MB Total Available Graphics Memory 1535 MB What happens is, i can use the laptop in "basic theme" ONLY, the moment i enable any aero theme, the screen tears up, discoloration appears & then laptop freezes. Sometimes its reboot itself with Blue Screen shows up the gfx card error. Any way around, highly appreciated.

    Read the article

  • Live cd and usb install failure blank screen when trying to install on an HP Pavilion dv6

    - by Ajian
    I recently bought a new computer, and have been trying to install linux on it, 11.10 x64. It is a HP pavilion dv6-6117dx. 2.4GHz/1.5GHz VISION A8 Technology from AMD with AMD Quad-Core A8-3500M Accelerated Processor AMD Radeon HD 6620G Discrete-Class Graphics I am pretty sure i picked a unsupported graphics card or something. I have tried booting from usb as well, but the screen becomes blank after rebooting.

    Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >