Search Results

Search found 11478 results on 460 pages for 'disk partition'.

Page 110/460 | < Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >

• Thunderbird gives " Not enough disk space " alert, after trying to download more emails ( Win 7, 64 bit )

  - by James C

  So, today I have installed Mozilla Thunderbird 24.2.0 on my Windows 7 (64 bit) machine. It was downloading emails, until it hit an error. An alert showed up saying : "There is not enough disk space to download new messages. Try deleting old mail, emptying the Trash folder, and compacting your mail folders, and then try again." Now, disk space is not a problem, there is enough free space left ( almost 50 % of the drive ). How to stop the alert and continue downloading ?

  Read the article

• which drive do I mount

  - by Crash893

  I have a system hdd then two raid1 hard drives I see that sda1 is the system drive but when i do a fdisk -l I get the following results so which of the following do i need to mount to get the "raid" drive and not the individual hdd? root@Mxxxx-PDC:/etc/samba# fdisk -l Disk /dev/sda: 251.0 GB, 251000193024 bytes 255 heads, 63 sectors/track, 30515 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000762dc Device Boot Start End Blocks Id System /dev/sda1 * 1 30328 243609628+ 83 Linux /dev/sda2 30329 30515 1502077+ 5 Extended /dev/sda5 30329 30515 1502046 82 Linux swap / Solaris Disk /dev/sdb: 400.0 GB, 400088457216 bytes 255 heads, 63 sectors/track, 48641 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 48641 390708801 83 Linux Disk /dev/sdc: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0009f4b2 Device Boot Start End Blocks Id System /dev/sdc1 * 1 255 2048256 fd Linux raid autodetect /dev/sdc2 256 30401 242147745 fd Linux raid autodetect Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000b7f4c Device Boot Start End Blocks Id System /dev/sdd1 * 1 255 2048256 fd Linux raid autodetect /dev/sdd2 256 30401 242147745 fd Linux raid autodetect

  Read the article

• How can I connect to my Airport Extreme Shared Disk using Windows?

  - by matt ryan

  I have a shared disk attached to my Airport Extreme, which I can connect to remotely in OS X through the finder via command - k, and entering in the proper address: afp://test.dyndns.org:1111 1111 being the port I've reserved for the disk in the AE port mapping. This is such a great feature, but I don't always have access to a Mac. My question is how can I connect to this drive via Windows XP? Please note, that the shared drive is a Drobo FS and formatted to handle both Windows and Mac OS. I've tried mapping a network drive via My Computer - Tools - Map Network Drive and entering: \\test.dyndns.org:1111\Drobo-Name I've also tried Start - Run and entering the same, both with and without the port #.

  Read the article

• What do I need to connect a hard disk to my laptop via non powered eSata?

  - by Ludo

  Hi there. I'm looking at getting a hard disk for my laptop (OCZ Vertex 2 SSD) which I would like to connect via eSata. My laptop has an eSata port, but it's not powered (Thinkpad T410). I presume this means I need more than just an eSata to eSata cable as it needs power, so does this mean I need a caddy for the hard disk as well which will provide power to the drive, or do I need one of them eSata cables that has a USB attachment too? I don't think the drive will come with a power supply. I realise this seems simple but I can't find an obvious answer online. Thanks for any assistance! Ludo.

  Read the article

• machine crash when connecting to external harddisk

  - by Gnot

  i recently had a problem with my laptop. when i booted up the machine, i would get a SMART failure error message and when i pressed F1 to continue, it would take a very long time to boot and it would come back to the same error message again. thinking that my hard disk was dying, i bought a new hard disk and installed on my laptop and so now my laptop is alright. however i need to recover data from that old hard disk, so i bought an external hard disk case and placed the old hard disk onto the case and connected to my laptop with USB. the first few times when i connected, i could see the files from the old hard disk and managed to copy some files over although it took extremely long to transfer. but now whenever i connect to the old hard disk, after a few minutes, my laptop will crash and re-boot. do you think my old hard disk is dead beyond repair? or you can offer some help here? any assistance would be appreciated!

  Read the article

• USB sector 0 not fount Kingston USB DT100 G2

  - by java

  Windows constantly asks me "Foramt Disk". when i go to command prompt and type format H: /fs:ntfs or format H: /fs:fat32 response: Cannot determine the number of sectors on this volume. if the benefit DISKPART detail disk Kingston DT 100 G2 USB Device Disk ID: 00000000 Type : USB Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : UNAVAILABLE Current Read-only State : No Read-only : No Boot Disk : No Pagefile Disk : No Hibernation File Disk : No Crashdump Disk : No Clustered Disk : No DISKPART detail volume Read-only : No Hidden : No No Default Drive Letter: No Shadow Copy : No Offline : No BitLocker Encrypted : No Installable : No Volume Capacity : 0 B Volume Free Space : 0 B what the problem?

  Read the article

• How do I access files inside a Wubi virtual ext4 Ubuntu partition from within Windows?

  - by aalaap

  I just installed Ubuntu 10.04 using Wubi on a PC that has Windows XP and Windows 7 installed. I was working in it for a while and everything is just fine. However, when I booted back into Windows 7, I couldn't figure out a way to access the files I had created or downloaded into the Ubuntu partition. They're in a virtual disk called root.disk in my C:\ubuntu\disks. Is there a way I can mount this vhd into Windows or at least browse the contents and extract what I need?

  Read the article

• In CentOS 4.3 Webmin 1.3000 bandwidth monitoring is eating disk space. How to delete those files?

  - by Silkograph

  I maintain Linux server being used for Mail, Squid and DNS service. Recently I observed that something was eating server disk space. But at last, today I caught the culprit which was consuming the disk by storing large number of files. On this server, Webmin 1.300 is installed. We use Squid proxy and Sarg to monitor Internet access. I always manually clear Sarg generated files under /var/www/html/squid for last few years. But I never realized that Webmin is also storing some kind of bandwidth log files in its' directory structure. I have noticed that under /etc/webmin/bandwidth/hours it has stored more thousands of files since year 2007 totaling about 17 GB. We have used 40 GB HDD for this server machine. My question is how can I delete those (/etc/webmin/bandwidth/hours) files safely?

  Read the article

• How can I retrieve data from a Western Digital Passport External Disk which is not getting recognized but getting shown as healthy in Device manager

  - by Rabimba Karanjai

  When I plug in this external harddisk It is not getting shown in the My Computer. But it gets shown perfectly well in the Device Manager When I go into the Computer Administrative panel and into the disk manager it asks me to initialize the disk Now when I try to initialize it, regardless of the method I try it shows me an error "Incorrect Function" As you can see windows tells me it is working properly. Is there anyway I can retrieve data from this?/access it? I have googled and it seems to be a frequent problem with WD drives. Anyone has any solutions on how I can get the data back?

  Read the article

• How is the 137GB limit counted in Virtual PC (two systems on one disk)?

  - by Nux

  I have a dual boot (Win7, XP) physical machine on my old computer which I want to virtualize and move to my new one. So I've uninstalled everything that I can and run shrink from RescueCD (used GParted). Now I have two about 80GiB partitions with a gap between them, so still this seem to be above the given limit. Still the resulting VHD (made with Disk2vhd) is much below the limit (about 110GiB) and both partitions are below the limit. So my question is - is it failing due to the limitations of disk size for VPC or is failing simply because it's a dual boot system. Or maybe it would work if I would move partitions to be close to each other (the gap between them is about 171GB and the whole physical disk is 1TB)?

  Read the article

• After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports.

  - by sin

  I have a big problem! After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports. I have to install windows in other PC which has usb 2.0port only! so I made usb booting disk using usb 3.0 in 3.0 port. but after that it never worked except in 3.0 ... and I could't restore my usb. I alredy fomated in cmd and others in usb3.0 port! but there is no change. and I couldn't find it in usb 2.0 port. plz help me.

  Read the article

• How do I get a USB hard-disk adaper to work with a PCMCIA USB card?

  - by Carl

  I have a PCMCIA (Cardbus) 32bit USB 2.0 2-port card. If I plug my MP3 player in it works fine. I have a USB adapter for a hard disk drive. When I plug that into the PCMCIA USB slot the light on that hard disk flashed between red and green - it should stay green. "USB Mass Storage device" is added in the Device Manager, but no drive letter appears in My Computer. The installing device icon down by the clock never goes away. (Windows XP SP3.)

  Read the article

• Laptop crashes when connecting to external harddisk

  - by Gnot

  I recently had a problem with my laptop. when I booted up the machine, I would get a SMART failure error message and when I pressed F1 to continue, it would take a very long time to boot and it would come back to the same error message again. Thinking that my hard disk was dying, I bought a new hard disk and installed on my laptop and so now my laptop is alright. However I need to recover data from that old hard disk, so I bought an external hard disk case and placed the old hard disk onto the case and connected to my laptop with USB. The first few times when I connected, I could see the files from the old hard disk and managed to copy some files over although it took extremely long to transfer. But now whenever I connect to the old hard disk, after a few minutes, my laptop will crash and re-boot. Do you think my old hard disk is dead beyond repair? Or you can offer some help here? Any assistance would be appreciated!

  Read the article

• How to move partition with Users to a new SATA controller?

  - by Al Kepp

  Our current situation: X79 chipset. Windows 7 installed on SATA SSD running on Marvell controller. C:\Users contains just Public and computer-name folders, all the other users are created in E:\Users. That partition is on two HDD's running on an Intel RAID controller. (The motherboard has got two SATA/RAID onboard controllers.) The goal is: Without reinstallation, I want to move SSD to a standard SATA controller. Then I want to get rid of RAID1, and move one HDD to the same internal Intel SATA controller and the current E:\Users move to that new place. I want it to stay as E:\users, but I need to reinstall the HDD to let it work in SATA mode without RAID. So I face several problems. I am sure all are solvable with free software utilities, but I don't know how exactly to do it. I can see the particular problems: I have got all users at E:\Users. When I turn off that E:\ disk, I won't be able to login to Windows. I need at least one admin account to be placed back at C:\users. The current C: runs on standard 120 GB SSD, but it is connected to a Marvell SATA/RAID controller. I am affraid the Windows won't let me put it to Intel SATA controller due to hardware/licence check, and I won't be able to use standard W7 recovery disk either, because there probably isn't marvel SATA/RAID driver on it. I haven't tried anything yet, because I am affraid I can end up with computer not working at all. (I want to move it to a standard ICH10 Intel SATA controller to let us have no problems in future with it. I think it is not very safe when we use any nonstandard hardware to boot the computer.) I need to somehow backup current E:\ disk and restore it to a new E:. I hope this will be the easy part (as long as the admin account will reside on C:). The E: RAID array is very large, but it is almost empty (less than 100 GB of data.) So I can make the partition smaller so it can easily fit to a single SATA HDD.

  Read the article

• Fedora 14 - Error 5 - No space on Disk - After installation.

  - by amitahire

  I am new to Fedora, am still figure my way through it. I was going about tweaking it and preparing it to my needs, While installing through yum I dont have much other than the fact that I have to search for the packages. But when I open "Add/remove software" of Fedora. I am greeted with " No space left on the disk" and when I seek for more details it says " Disk Error :[errno 5] Input/output error" I did some research and I saw that it usually occurs during installation, but here I have successfully installed it. Can someone help me with it? Later on I even had notification of the same warning. And mind you I got loads of free space. Thanks for the help

  Read the article

• How to reduce Fedora's disk size in VMware player.

  - by user428862

  I'm new to Fedora 14, vmware player. After getting Fedora up and running in VMware player. The disk size was 2.7 GB. After three hours of working with it, the disk size has bloated to 4.3 GB. I havent added software to account for the near doubling in size. How do I reduce the size back to 2.7GB range or lower. Im new to Fedora and superuser controls. Im removing more software than adding software. Is this a VMWARE problem or Fedora problem?

  Read the article

• Why Virtualbox VDI doubles the space of the VM hard disk?

  - by logoff

  I have one Xubuntu 12.10 64 bit Virtualbox VM on a Windows 7 64 bit host. It has one dynamic allocated hard disk with VDI format with maximum capacity of 20GB. If I use a command df -h in the VM I get that 5.3GB are in use in th main partition. I have only 2 partitions, one for the ext4 hard disk and another with 512MB of swap. I have no snapshots. The VDI file of this VM has 10.7GB. It is normal this difference of space? It is caused because the VDI format?

  Read the article

• Laptop HDD not mounting.

  - by D3X

  I have a laptop with broken (shorted out) motherboard and a 640 GB HDD. I want to recover my data from the hard disk. Every time I connect the hard disk using an external casing, it is being detected in the disk management service but not visible in my computer, nor accessible through command prompt. The Hard Disk is functioning as I can feel the hard disk rotor working properly when connected using the casing. Also the LED on the hard disk is blinking, the data is there but i am unable to access the data. Someone please suggest me ways of using the hard-disk as a slave disk using casing.

  Read the article

• RAID 0 disk failure, how to recover the RAID?

  - by user7985

  Situation is this. A PC with 2 hard disks, in an RAID 0 Array. The electronics on one of the disks has failed. I can not find the same board for the disk (I've tried this, removed board from the OK disk, and the second, the damaged one, works fine). I've made an image with "dd" on linux on a new hard drive (same size, not same model) and now I get "Offline member" in the RAID config screen. Will I succeed to recover the data which is stored on the drives, any help, any experience with this kind of problem. And surly, I know it was stupid to put the disks in RAID 0 and store data on them :(

  Read the article

• How to save your Linux state (suspend to disk) periodically to recover from crashes?

  - by WoLpH

  One in a while my laptop crashes/dies because of a bad/empty battery, crappy wifi driver or whatever other reason. For a while I've wondered if it's possible to force Linux to periodically save the state (like vmware snapshots) to disk so you can restore from that with possibly slightly outdated work but at least with all of your apps open in the same state you've left them. I don't really see the point in having to boot everything from cratch constantly, although KDE saves your state on logout, that doesn't happen periodically (by default) either. It would make it much nicer to recover from your crashes if your ram was written to disk periodically. Anyone know if there's a system call to do this without also shutting down the machine? Even a manual button to save the entire state would be nice.

  Read the article

• format/build raid 5 with one 4k drive, three 512b

  - by skidawgz

  I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

  Read the article

• I can't install Ubuntu on my Dell Inspiron 15R at all

  - by Kieran Rimmer

  I'm attempting to install Ubuntu 12.04LTS, 64 bit onto a Dell Inspiron 15R laptop. I've shrunk down one of the windows partitions and even used gparted to format the vacant space as ext4. However, the install disk simply does not present any options when it comes to the partitioning step. What I get is a non-responsive blank table As well as the above, I've changed the BIOS settings so that USB emulation is disabled (as per Can't install on Dell Inspiron 15R), and changed the SATA Operation setting to all three possible options. Anyway, the install CD will bring up the trial version of ubuntu, and if I open terminal and type sudo fdisk -l, I get this: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xb4fd9215 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/sda2 * 81920 29044735 14481408 7 HPFS/NTFS/exFAT /dev/sda3 29044736 1005142015 488048640 7 HPFS/NTFS/exFAT /dev/sda4 1005154920 1953520064 474182572+ 83 Linux Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb4fd923d Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive If I type 'sudo parted -l', I get: Model: ATA WDC WD10JPVT-75A (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 41.1MB 41.1MB primary fat16 diag 2 41.9MB 14.9GB 14.8GB primary ntfs boot 3 14.9GB 515GB 500GB primary ntfs 4 515GB 1000GB 486GB primary ext4 Model: ATA SAMSUNG SSD PM83 (scsi) Disk /dev/sdb: 32.0GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 8589MB 8588MB primary Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: Can't have a partition outside the disk! I've also tried a Kubuntu 12.04 and Linuxmint install disks, wityh the same problem. I'm completely lost here. Cheers, Kieran

  Read the article

• Windows 7 disappeared in list of Grub while loading

  - by Riyad A.

  Installed Ubuntu 12.04 alongside the Windows 7 two weeks ago. Initially haven't any issues with that. day ago installed updates on Ubuntu and after restarting the system found the absence of Win7 in Grub list. Before the HDD has been partitioned on two volumes Disk C and Work Disk(don't remember the name). When doing the fdisk -l: Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xa93031e0 Device Boot Start End Blocks Id System /dev/sda1 * 2048 408833842 204415897+ 7 HPFS/NTFS/exFAT /dev/sda2 488386560 976773119 244193280 7 HPFS/NTFS/exFAT /dev/sda3 408834046 488386559 39776257 5 Extended Partition 3 does not start on physical sector boundary. /dev/sda5 408834048 484421631 37793792 83 Linux /dev/sda6 484423680 488386559 1981440 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes 49 heads, 48 sectors/track, 3292 cylinders, total 7744512 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/mmcblk0p1 8192 7744511 3868160 b W95 FAT32 When sudo mount /dev/sda ~/1 -o offset [488386560*512] - opens and mounts WORK disk. Need help: how to See and mount disk C. how to see and adjust the Grub to appear both systems in Grub menu when loading?

  Read the article

• how to make a partition which is in ext-2 , a writable disk?

  - by mekasperasky

  i have debian system in which i have mounted the OS on a ext-3 system . I have got a partition of 60 gb , which is formatted to ext-2 partition . Even if I mount , i cant write anything into it . How can i change that ? How can I make the disk writable?

  Read the article

• How to update the hard disk device drivers for a ghosted hard drive image so it can run on different hardware: Ultra ATA > SATA

  - by rism

  I've ghosted a Winxp machine from one laptop with Ultra ATA drive, and would like to set it up on another laptop as a multiboot option on another hard driver with a SATA drive. I can install the partition fine but if i make it active and try to boot it it blue screens. The blue screen is so fast i cant even read it, other than to make out it's saying "something", im picking probably hard drive as it goes through POST fine. So basically i would like to boot into my Win7 OS, and then somehow manipulate the XP partition to use updated drivers for the new hard drive/laptop so that i can then at least boot into the XP OS on the new machine and update all the other drivers in safe mode or whatever to get it to run. I assume someone is going to tell me to just do a fresh install, but that kinda defeats the purpose of ghosting at this point. There is a significant amount of personalisation, development setup on the XP machine that i would like to just transfer as is. As it stands ive invested minmal time in getting it to run, just a ghost and recovery and then a blue screen boot or two, so its still well worth it to me, time wise to try this way. Thanks.

  Read the article

< Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >