Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 111/1617 | < Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >

• Connected to Access Point but no internet connection?

  - by ReaZem

  I am trying to use my school's WPA Enterprise network to access the internet with my Three-OS laptop. I currently have Windows7, Ubuntu11.10 and Backtrack5 installed. I can use my home's WPA2 network without any issues with the 3 OS. I can successfully connect to my school's network with the 3 OS but I can only browse the internet with windows7. Ubuntu network-manager and Backtrack WICD both say that I am connected to the Acces Point but I cannot browse the internet. I have tried uninstalling network-manager and installing WICD but it did not solve the problem. Every time I connect to the Access Point, I am able to browse the internet for about 10 seconds. I have tried disabling IPV6 I have tried changing DNS.

  Read the article

• Wired connection not working

  - by YokoBlac

  I am using a Acer Aspire One. Here is the Ubuntu Wiki Page about my computer. I have a working wireless connection however when I plug a cat5 (Ethernet) cable in the lights flicker on the computer, but then nothing happens. Output of iconfig: eth0 Link encap:Ethernet HWaddr 00:1e:68:96:1a:6b inet6 addr: fe80::21e:68ff:fe96:1a6b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2622 (2.6 KB) TX bytes:936 (936.0 B) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) wlan0 Link encap:Ethernet HWaddr 00:22:68:92:7f:36 inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:68ff:fe92:7f36/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5702 errors:0 dropped:0 overruns:0 frame:0 TX packets:5284 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4117327 (4.1 MB) TX bytes:936709 (936.7 KB) Any understanding of this output is greatly appreciated.

  Read the article

• Connect to wifi ubuntu 14.04 (new ubuntu user)

  - by user289168

  I have recently changed my operating system from windows 8 to ubuntu 14.04, when trying to connect to the network via wifi the system just keeps asking for my password over and over without connecting. The connectivity through an Ethernet cable is perfectly fine however and my wifi worked fine through windows 8, I have very little ubuntu knowledge so i apologise if the right information is not shown in this question. Just wondering if there was any known problems or if anyone has seen this before? Thanks in advance for any help, Tom

  Read the article

• Flikering line on top of display

  - by jaskaran

  I just bought a new Dell Inspiron pre-installed with Ubuntu 11.10. All was fine until I updated the OS. Since then, I have this flickering line at the top of my screen and it won't go after rebooting or changing the screen resolution. It gets really annoying. I don't know which update did this. I tried reinstalling the image from Dell, and it worked fine until I applied the updates. I tried to take a screen shot but it does not show. The line seems to be outside the desktop area. Help please... Thanks!

  Read the article

• Techniques to prevent non-official clients in network gaming?

  - by UpTheCreek

  In multi-player network games, what techniques exist to try to ensure that users are connecting with the official client application, and not some hacked client app? I realise there is probably no sure-fire way to do this, but rather I'm interested in techniques that can be employed to mitigate the problem. I'm especially interested in any techniques that can be used for web based games, but I imagine most can be applied generally. Thank you!

  Read the article

• How to set up dual wired and wireless connections?

  - by Col

  My laptop has both wireless and a wired connection capabilities. Can I connect to a router A using wireless and a separate router B using wired ethernet at the same time without having to switch back and forth? Thanks for replying so quickly. I wish to connect to two separate networks. The wireless connection is to router A which is connected to broadband internet. The wired connection is to router B which I wish to share files and a printer on 1 or 2 other desktops also using wired connections on B and maybe using synergy to have only one keyboard and mouse for 2 desktops. The wireless laptop is the only one required to have internet access.

  Read the article

• Having trouble installing Bradcom STA driver

  - by user192881

  I just installed Ubuntu and love it so much, its so fast now. But I have a problem connecting to the internet. I checked and saw I have to install the driver Broadcom STA wireless driver but every time I do try to install it it says: Sorry, installation of this driver failed. Please have a look at the log files for details: /var/log/jockey.log I went to the terminal and copy and pasted the log file name. and when I did it, it said I have no permission to access this file. I checked on the forums that I have to be on a wired connection. So I plugged my laptop into my router and I got internet then tried to install the driver again. And it was loading then when it got to the end the same message popped up. Also I have one of those little USB router things you plug into the computer and it gives you internet I have been using that but its to slow. So I want to use the one in my computer but cant. Also I tried the command: sudo modprobe wl and when i type that command in it says: FATAL: Module wl not found Also I'm using Ubuntu 12.04

  Read the article

• ssh login information

  - by bob

  As the admin of my machine, I want users to be able to log into my computer with ssh, but I'm looking for a graphical way to be notified that a user is connected at the moment. If multiple users are connected, I want a list of connected users, their location, name, etc. This could be in the form of a forceCommand and 'alert' command when someone logs in, plus a icon saying how many people are connected right now in the notification bar, with the option to click on it to have more information about these users. Is there such a tool available in ubuntu, and if not, how to do it (I'm guessing it's not that difficult and could be done with under ten bash command lines) ?

  Read the article

• Client Side Prediction

  - by user13842

  I have a question regarding Client Side prediction. Ive tried to search topics about my specific problem but couldn't find anything which really answered my problem. Most tutorials and explanations assume that the Client sends messages like "Move my player up by 1 Position", but what if i send messages like "Set my player's velocity to x"? Since it's hard to explain with text, i made a graphic explaining my problem. The main problem is, that the player sets his own velocity, due to Client Side Prediction, earlier than the Server. So if 2 different velocities overlap, the Server would get out of sync. How can i tackle that problem? Thanks a lot. Graphic: http://img27.imageshack.us/img27/6083/clientpred.png (Ignore the 5.5cm)

  Read the article

• how to congest a link using iperf

  - by navaz

  I have setup like below. Switch1-------------------- Switch2 | | | | | | | | | | | | PC1 PC2 PC3 PC4 I have a video traffic is flowing between PC1 and PC4. I have configured PC2 as iperf server. ( iperf -s ) and PC3 as client . (iperf -c 10.10.10.2 -P 20 -t 10000) where 10.10.10.2 is PC2 IP. now I am seeing most of the traffic in a link (switch1---switch2) is iperf. (TCP). I have observed from the logs that 1 out of 300 packet is UDP. Still I am not seeing any difference in the quality of video streaming in PC4. It looks similar compared to the case with no iperf. I am checking QOS, I have tried many options with iperf, couldnt succeed. I want to diminish the quality of video streaming in PC4. Could you please tell me what options can be used along with iperf to do it. Bandwidth between Switch1---switch2 is 1Gbits/sec. Thanks in advance

  Read the article

• How to run just one application over ethernet while others on wifi

  - by db42

  I normally connect my laptop via wifi. However, I would like to use synergy to share my workplace desktop machine with my laptop. But the problem is that my desktop machine doesn't have wireless support. So, I have no other options except using ethernet to connect them. My first question is - Is it possible to use ethernet for synergy and keep using wifi for all other application. If the answer is yes, can somebody please guide me how to achieve this. Thanks,

  Read the article

• Cannot find other computers on the network

  - by RDNY

  I have several issues trying to connect to my network. This is not the problem connecting to the Internet through the same router. All my computers are running Windows 7, Vista and XP Pro. I can't see them and they can't see me either. I've already install Ubuntu Studio 11.10 three times and still not showing the network icon at all. I'm new to UBUNTU and LINUX in general. I can't find my group name either.

  Read the article

• C#/.NET Command Line Argument Parser Reloaded

  Easy to use yet powerful command line argument parser, which also creates usage and parameter information for the user.

  Read the article

• Internet (HTTP) is not working on Sony Viao

  - by vijay

  I switched my sony viao laptop from XP to ubuntu 10.04 recently. I have it connected through router at home. The internet was working fine with XP. With ubuntu, i am not able to connect to interenet. I am able to update using apt, and i am able to ping too. It seems like there is a DNS issue, when i try to goto sites from firefox, it doesn't work. I tried disabling the ipv6 in firefox config, it doesn't work. My router is on 192.168.2.1 instead of 192.168.1.1 any ideas on what config i might need to change to make this work? or could this be a drive issue?

  Read the article

• How to get wireless and wired network working again on my Dell Inspiron 1501?

  - by Angelo Daul

  My wireless doesn't work with Ubuntu 12.04.(it worked with 10.04 LTS) I have a Dell Inspiron 1501. I followed the steps posted below:(from a similar tag, but...) sudo apt-get install --reinstall bcmwl-kernel-source broadcom-sta-common broadcom-sta-source echo "blacklist brcmsmac" | sudo tee -a /etc/modprobe.d/blacklist.conf echo "blacklist bcma" | sudo tee -a /etc/modprobe.d/blacklist.conf ....and now i have no Network device on my PC(wired or wireless) I can use wired conection if i start my laptop with a"previsious version of Linux"...2.26.43... I am a beginner in Linux These are my hardware: 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [ 14e4:4311] (rev 01) 08:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [ 14e4:170c] (rev 02)

  Read the article

• eth0 not working on startup

  - by user4106

  Hi to all, This might sound strange but, working with my Lubuntu 10.04 i've experienced troubles when connecting to my eth0 newtwork. After some googling, i've found out that by writting in the CLI the following command: mii-tool eth0 -F 10baseT-FD and activating the eth0 in the toolbar (by clicking "activate eth0") everything works just fine. Well, up to now, i did not have any problem, because every time i turned on the computer i had to do this, but it was very little effort.But now, i would like to use the machine as a file server, accesing it by ssh, without monitor or keyboard. So, i won't be able to make this actions, and can't do this at startup because mii-tool needs root permissions. So, the question is: Do you know what does that command do, and how can id make that change permanent? Or do you know any other solution for my problem? I hope i was clear! If not, tell me and i'll try to be as clearer as possible. Thanks in advance!

  Read the article

• Please help with samba, can't access files from other computer

  - by user254074

  Maybe I am missing something but all I want to do is be able to access and transfer files from one folder on my main computer to my htpc. Both computers are running Ubuntu 14.04. I followed the instructions on this video but I am not sure if I need to do something on the HTPC to access my Movie folder. I went into nautilus then Browse Network Windows Network Workgroup but I get an error and it won't let me access it. Is there something I am doing wrong?

  Read the article

• Why hamachi time-outs after 5 minutes or so?

  - by Vik89

  I installed hamachi and hamachi-gui on my girlfriend's pc and on my girlfriend's netbook. After 5 minutes or so (even if I keep using it during that time) it loses the connection, I mean I have to 'go offline' and then 'go online' again for it to see my ip again. If I don't and I ping my IP, it says 'Host unreachable'. If I connect with my Mac from the office the problem doesn't exist, so I wouldn't say it is a problem of my hamachi (server) installation, I'm tempted to say it is a problem of my girlfriend's connection, since it happens from her home, and we haven't tried yet to connect from another home with her setup. What would you say? I followed these instructions http://ubuntuforums.org/showthread.php?t=135036

  Read the article

• I can not print on Windows 7 shared printer

  - by lrichard

  For a while I can not print from my Ubuntu 12.04 64 bit pc on a Windows 7 shared printer. Before that everything was ok. The printer is HP LaserJet 1100. The error message is: "File "/usr/lib/cups/backend/smb" not available: No such file or directory" I have tried to reinstall the samba, I have configured the workgroup properly. I have tried to reinstall the printer on the Ubuntu machine with the proper address, or with lpd (I have read somewhere). If I restart the printer on the cups web interface ("Resume Printer") the problem seems to be solved, but not. (The printer seems to be idle, and if I want to print, I still get the error message.) I have checked the share rights on the Windows 7 pc, and I think it is ok.

  Read the article

• How to join a Windows Domain an Map NEtwork Drives on Ubuntu Partition

  - by AgainstClint

  I just installed the current build for Ubuntu on a partition for my work computer. I am a novice when it comes to Linux/Ubuntu, which is why I installed it along side windows. I want to learn how to operate and use Ubuntu much more than I do now, so I figured installing it and trying to do day to day functions here would be a "Thrown into the pool with sharks" way to do it, and I like that way. I did however have a few questions: We are on a Domain in Windows, is there any way to join that domain using the Ubuntu partition? We Also have 16 mapped network drives. I don't actually need ALL of them mapped for Ubuntu, but is there a way to Map at least one of them to see/use here in Ubuntu. Outlook Corporate email, how can I sign in/use it while...well, you get the idea. As I said earlier, I am VERY new to Ubuntu, i've only played around with it a bit at home and never at the office. If you could simplify it down for me a bit, that would be great.

  Read the article

• Network doesn't work after upgrading to 13.10

  - by Inkbug

  I upgraded from 13.04 to 13.10, and a number of things stopped working. Most importantly, I don't have internet access anymore. When I go to the network settings, I receive the following error: The system network services are not compatible with this version. The only settings that show up in the network settings are the proxy settings. I tried sudo service network-manager start and sudo service network-manager restart, but it told me the service was already running. In addition, the menu bar is missing all of the indicators (such as keyboard layout, sound, network, clock, and the gear icon). Is this related or a separate issue?

  Read the article

• MAC filtering after DHCP

  - by user1655161

  How to manage filtering by MAC in Ubuntu? Scenario: Ubuntu DHCP is configured and working (network 192.168.1.0) a) Laptop 1 is set in configuration on Ubuntu as static IP Laptop 1 is configured for automatic IP and when is connected to server everything works. I'm taking laptop 2 which is configured as static IP 192.168.1.10 and his configuration is not set in Ubuntu dhcpd.conf After laptop 2 is connected internet working. It is possible to do MAC filtering which disallow to connect PCs with address IP set as static but MAC address is not configured in Ubuntu (something like: intruder in network)?

  Read the article

• How To Setup Domain Name for SchoolTool Local Server

  - by zeroseven0183

  I am currently testing SchoolTool 2.0 and I would like to do some things: This application is installed on a virtual machine running Ubuntu Server 11.10 bridged to our home network. The site is accessible through IP address. What I would like to do is setup a local domain, say schooltool.ourhomedomain.com. I thought my sister would appreciate it more if it were not via IP address. If there's anymore information needed, let me know. Thanks in advance!

  Read the article

• lshw not showing network

  - by triunenature

  Output: {User}@{Computer}:~$ sudo lshw -class network {User}@{Computer}:~$ Another Test: {User}@{Computer}:~$ lspci 00:00.0 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: NVIDIA Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: NVIDIA Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a2) 00:02.0 USB controller: NVIDIA Corporation MCP61 USB 1.1 Controller (rev a3) 00:02.1 USB controller: NVIDIA Corporation MCP61 USB 2.0 Controller (rev a3) 00:04.0 PCI bridge: NVIDIA Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: NVIDIA Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: NVIDIA Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: NVIDIA Corporation MCP61 Ethernet (rev a2) <<---- Network Card???? 00:08.0 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2) 00:08.1 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 FireWire (IEEE 1394): LSI Corporation FW322/323 (rev 70) 02:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9500 GT] (rev a1) If you look at 00:07.0 I believe that is the network card. However lshw doesnt show it. I mainly need information on network speed 10MBpS/100MBsP/1000MBpS Though knowing why my system isn't working would be nice.

  Read the article

• How to make my proxy settings change depending on the network I connect to?

  - by Little Jawa

  My company's corporate network requires me to set a network proxy to access the net, but when I am anywhere else, I don't need it. The proxy settings in Ubuntu (System - Preferences - Proxy server) allowed me to create "locations" that I can manually select. Then I have a "default" location (with no proxy) and a "work" location (with my company's proxy in it). Is there a way to make Ubuntu automatically select the "work" location based on the connection I'm using? I thought I could use the IP subnet (very specific) to detect where I am, but I have no idea how to set it up... Edit: I really need to have the proxy settings set at the system level. All my network connections (IMAP, SMTP, chat, etc) need to go through the proxy. Not only the web browser.

  Read the article

< Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >