Search Results

Search found 13936 results on 558 pages for 'safe mode'.

Page 112/558 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

  • How to start Ubuntu with no working video card?

    - by ViliusK
    I have a laptop with broken video card. It has two operating systems installed - Windows 7 and Ubuntu 10.10 Desktop Edition. It has GRUB to manage which operating system to boot up. Windows is default OS. And Windows fails to boot up without video card. I'm checking with ping to the ports which are shown as used by DHCP in my router. Normal boot of Ubuntu also fails and it restarts after a while. But when I choose (blindly, but checking HDD indicator and by counting button presses when GRUB menu appears) to boot second option of Ubuntu (rescue mode) it starts and I can ping it. But when I try to connect to it through SSH, I'm getting "connection refused" error from putty. I've took out HDD from my laptop already and inserted it to WD Passport case so now I can connect it to other computer to edit configuration files. How can I check if SSH server is working? How to enable it in rescue mode? Or better, how to disable video card to be required while booting Ubuntu in normal mode?

    Read the article

  • External Full HD monitor and Virtual Desktop Size

    - by Stefan
    I have two FullHD monitors attached to my ATI graphics card [2]. The resolution of both of them is detected properly without any modifications to /etc/X11/xorg.conf. I can run both of them in clone mode. However, when I try to run them next to each other, I got the following error: The selected configuration for displays could not be applied. If tried to fix this according to [1]. My xorg.conf now looks like this: Section "Module" Load "glx" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" # The 1088 is the smallest multiple of 32 >= 1088 # see manpages Virtual 1920 1088 EndSubSection EndSection This does not seem to be parsed properly. After restarting X, I cannot set resolutions beyond 1600 or so any more. /var/log/Xorg.0.log gives: [ 15.676] (II) fglrx(0): Not using mode "1920x1080" (width too large for virtual size) [ 15.676] (II) fglrx(0): Not using mode "1680x1050" (width too large for virtual size) Are my modifications syntactically incorrect? According to the man page, it should be fine. Any ideas? OS: Ubuntu 11.10 64bit [1] http://askubuntu.com/a/75546/5023 [2] 01:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5700 Series]

    Read the article

  • Can't install Ubuntu in Windows 8

    - by user171635
    I’ve been trying to install Ubuntu 13.04 64-bit edition on an ASUS (K53Z) laptop. I have Windows 8 64-bit installed in a non UEFI mode (I think since it starts-up with the Windows logo and I don’t have the UEFI settings). This laptop had installed Windows 7 and when I upgraded it I didn’t knew about the UEFI advantages. I tried several times to install Ubuntu from a USB device and it loads the logo and then I can’t go further in the installation. I thought it was the version of Ubuntu and tried to install Fedora (even if I personally prefer Ubuntu). I had the same problem: Fedora’s logo appears and it gets stuck. I tried also to boot from different USB devices and didn’t work either. My Bios has EFI options to boot but they were not enabled. So I tried to enable them to boot the USB in UEFI mode. A menu shows up with the options of install Ubuntu and try Ubuntu. If I click the Install or try option, I get a black screen and I can’t go further with the install (which I think is normal since I don’t have Windows 8 in EFI mode). My hypothesis is that the Bios isn’t letting Ubuntu write or read from my SSD, because the activity LED in the USB memory is on when it’s loading the installation files. Once the files are ready and the Ubuntu logo is loaded I don’t see a LED activity on neither the SSD or the USB. Thanks If I missed data you can ask me.

    Read the article

  • Extended display - nightmare

    - by user206343
    I have been struggling for quite a while, and I hope one of you can shed some lights on my issue. I am using Xubuntu 13.10 (Ubuntu 12.04LTS behaves the same way, higher version wouldn't install, LinuxMint didn't install, Fedora didn't install). I am trying to set extend display for two dell monitors 1900x1200. It works great when in mirror mode, but I just cannot extend the display. Either one monitor goes to sleep and the other is unresponsive, or both work but are unusable. This is a link to the picture of my monitors in mirror mode This is link showing what happens after I try to extend the desktop I get the same results if I use aRandr or the built in configuration utility. I have an ATI Radeon X300 card. I cannot use proprietary Catalyst drivers (I would have to use the legacy ones, which would force me into using much older version of the OS). Extension is possible with Windows. I am hoping someone can come up with tweaks that would allow me to run an extended desktop. I truly love Xubuntu (and Ubuntu, unfortunately, Unity is a bit too heavy for my old PC, and I have to run in 2D mode, so 12.04 is as high as I can go). I have tried everything I could find online, but nothing worked thus far. I believe some configuration or something I am missing might work. Please, if you have any idea, do not hesitate. Thanks guys.

    Read the article

  • Creating STA COM compatible ASP.NET Applications

    - by Rick Strahl
    When building ASP.NET applications that interface with old school COM objects like those created with VB6 or Visual FoxPro (MTDLL), it's extremely important that the threads that are serving requests use Single Threaded Apartment Threading. STA is a COM built-in technology that allows essentially single threaded components to operate reliably in a multi-threaded environment. STA's guarantee that COM objects instantiated on a specific thread stay on that specific thread and any access to a COM object from another thread automatically marshals that thread to the STA thread. The end effect is that you can have multiple threads, but a COM object instance lives on a fixed never changing thread. ASP.NET by default uses MTA (multi-threaded apartment) threads which are truly free spinning threads that pay no heed to COM object marshaling. This is vastly more efficient than STA threading which has a bit of overhead in determining whether it's OK to run code on a given thread or whether some sort of thread/COM marshaling needs to occur. MTA COM components can be very efficient, but STA COM components in a multi-threaded environment always tend to have a fair amount of overhead. It's amazing how much COM Interop I still see today so while it seems really old school to be talking about this topic, it's actually quite apropos for me as I have many customers using legacy COM systems that need to interface with other .NET applications. In this post I'm consolidating some of the hacks I've used to integrate with various ASP.NET technologies when using STA COM Components. STA in ASP.NET Support for STA threading in the ASP.NET framework is fairly limited. Specifically only the original ASP.NET WebForms technology supports STA threading directly via its STA Page Handler implementation or what you might know as ASPCOMPAT mode. For WebForms running STA components is as easy as specifying the ASPCOMPAT attribute in the @Page tag:<%@ Page Language="C#" AspCompat="true" %> which runs the page in STA mode. Removing it runs in MTA mode. Simple. Unfortunately all other ASP.NET technologies built on top of the core ASP.NET engine do not support STA natively. So if you want to use STA COM components in MVC or with class ASMX Web Services, there's no automatic way like the ASPCOMPAT keyword available. So what happens when you run an STA COM component in an MTA application? In low volume environments - nothing much will happen. The COM objects will appear to work just fine as there are no simultaneous thread interactions and the COM component will happily run on a single thread or multiple single threads one at a time. So for testing running components in MTA environments may appear to work just fine. However as load increases and threads get re-used by ASP.NET COM objects will end up getting created on multiple different threads. This can result in crashes or hangs, or data corruption in the STA components which store their state in thread local storage on the STA thread. If threads overlap this global store can easily get corrupted which in turn causes problems. STA ensures that any COM object instance loaded always stays on the same thread it was instantiated on. What about COM+? COM+ is supposed to address the problem of STA in MTA applications by providing an abstraction with it's own thread pool manager for COM objects. It steps in to the COM instantiation pipeline and hands out COM instances from its own internally maintained STA Thread pool. This guarantees that the COM instantiation threads are STA threads if using STA components. COM+ works, but in my experience the technology is very, very slow for STA components. It adds a ton of overhead and reduces COM performance noticably in load tests in IIS. COM+ can make sense in some situations but for Web apps with STA components it falls short. In addition there's also the need to ensure that COM+ is set up and configured on the target machine and the fact that components have to be registered in COM+. COM+ also keeps components up at all times, so if a component needs to be replaced the COM+ package needs to be unloaded (same is true for IIS hosted components but it's more common to manage that). COM+ is an option for well established components, but native STA support tends to provide better performance and more consistent usability, IMHO. STA for non supporting ASP.NET Technologies As mentioned above only WebForms supports STA natively. However, by utilizing the WebForms ASP.NET Page handler internally it's actually possible to trick various other ASP.NET technologies and let them work with STA components. This is ugly but I've used each of these in various applications and I've had minimal problems making them work with FoxPro STA COM components which is about as dififcult as it gets for COM Interop in .NET. In this post I summarize several STA workarounds that enable you to use STA threading with these ASP.NET Technologies: ASMX Web Services ASP.NET MVC WCF Web Services ASP.NET Web API ASMX Web Services I start with classic ASP.NET ASMX Web Services because it's the easiest mechanism that allows for STA modification. It also clearly demonstrates how the WebForms STA Page Handler is the key technology to enable the various other solutions to create STA components. Essentially the way this works is to override the WebForms Page class and hijack it's init functionality for processing requests. Here's what this looks like for Web Services:namespace FoxProAspNet { public class WebServiceStaHandler : System.Web.UI.Page, IHttpAsyncHandler { protected override void OnInit(EventArgs e) { IHttpHandler handler = new WebServiceHandlerFactory().GetHandler( this.Context, this.Context.Request.HttpMethod, this.Context.Request.FilePath, this.Context.Request.PhysicalPath); handler.ProcessRequest(this.Context); this.Context.ApplicationInstance.CompleteRequest(); } public IAsyncResult BeginProcessRequest( HttpContext context, AsyncCallback cb, object extraData) { return this.AspCompatBeginProcessRequest(context, cb, extraData); } public void EndProcessRequest(IAsyncResult result) { this.AspCompatEndProcessRequest(result); } } public class AspCompatWebServiceStaHandlerWithSessionState : WebServiceStaHandler, IRequiresSessionState { } } This class overrides the ASP.NET WebForms Page class which has a little known AspCompatBeginProcessRequest() and AspCompatEndProcessRequest() method that is responsible for providing the WebForms ASPCOMPAT functionality. These methods handle routing requests to STA threads. Note there are two classes - one that includes session state and one that does not. If you plan on using ASP.NET Session state use the latter class, otherwise stick to the former. This maps to the EnableSessionState page setting in WebForms. This class simply hooks into this functionality by overriding the BeginProcessRequest and EndProcessRequest methods and always forcing it into the AspCompat methods. The way this works is that BeginProcessRequest() fires first to set up the threads and starts intializing the handler. As part of that process the OnInit() method is fired which is now already running on an STA thread. The code then creates an instance of the actual WebService handler factory and calls its ProcessRequest method to start executing which generates the Web Service result. Immediately after ProcessRequest the request is stopped with Application.CompletRequest() which ensures that the rest of the Page handler logic doesn't fire. This means that even though the fairly heavy Page class is overridden here, it doesn't end up executing any of its internal processing which makes this code fairly efficient. In a nutshell, we're highjacking the Page HttpHandler and forcing it to process the WebService process handler in the context of the AspCompat handler behavior. Hooking up the Handler Because the above is an HttpHandler implementation you need to hook up the custom handler and replace the standard ASMX handler. To do this you need to modify the web.config file (here for IIS 7 and IIS Express): <configuration> <system.webServer> <handlers> <remove name="WebServiceHandlerFactory-Integrated-4.0" /> <add name="Asmx STA Web Service Handler" path="*.asmx" verb="*" type="FoxProAspNet.WebServiceStaHandler" precondition="integrated"/> </handlers> </system.webServer> </configuration> (Note: The name for the WebServiceHandlerFactory-Integrated-4.0 might be slightly different depending on your server version. Check the IIS Handler configuration in the IIS Management Console for the exact name or simply remove the handler from the list there which will propagate to your web.config). For IIS 5 & 6 (Windows XP/2003) or the Visual Studio Web Server use:<configuration> <system.web> <httpHandlers> <remove path="*.asmx" verb="*" /> <add path="*.asmx" verb="*" type="FoxProAspNet.WebServiceStaHandler" /> </httpHandlers> </system.web></configuration> To test, create a new ASMX Web Service and create a method like this: [WebService(Namespace = "http://foxaspnet.org/")] [WebServiceBinding(ConformsTo = WsiProfiles.BasicProfile1_1)] public class FoxWebService : System.Web.Services.WebService { [WebMethod] public string HelloWorld() { return "Hello World. Threading mode is: " + System.Threading.Thread.CurrentThread.GetApartmentState(); } } Run this before you put in the web.config configuration changes and you should get: Hello World. Threading mode is: MTA Then put the handler mapping into Web.config and you should see: Hello World. Threading mode is: STA And you're on your way to using STA COM components. It's a hack but it works well! I've used this with several high volume Web Service installations with various customers and it's been fast and reliable. ASP.NET MVC ASP.NET MVC has quickly become the most popular ASP.NET technology, replacing WebForms for creating HTML output. MVC is more complex to get started with, but once you understand the basic structure of how requests flow through the MVC pipeline it's easy to use and amazingly flexible in manipulating HTML requests. In addition, MVC has great support for non-HTML output sources like JSON and XML, making it an excellent choice for AJAX requests without any additional tools. Unlike WebForms ASP.NET MVC doesn't support STA threads natively and so some trickery is needed to make it work with STA threads as well. MVC gets its handler implementation through custom route handlers using ASP.NET's built in routing semantics. To work in an STA handler requires working in the Page Handler as part of the Route Handler implementation. As with the Web Service handler the first step is to create a custom HttpHandler that can instantiate an MVC request pipeline properly:public class MvcStaThreadHttpAsyncHandler : Page, IHttpAsyncHandler, IRequiresSessionState { private RequestContext _requestContext; public MvcStaThreadHttpAsyncHandler(RequestContext requestContext) { if (requestContext == null) throw new ArgumentNullException("requestContext"); _requestContext = requestContext; } public IAsyncResult BeginProcessRequest(HttpContext context, AsyncCallback cb, object extraData) { return this.AspCompatBeginProcessRequest(context, cb, extraData); } protected override void OnInit(EventArgs e) { var controllerName = _requestContext.RouteData.GetRequiredString("controller"); var controllerFactory = ControllerBuilder.Current.GetControllerFactory(); var controller = controllerFactory.CreateController(_requestContext, controllerName); if (controller == null) throw new InvalidOperationException("Could not find controller: " + controllerName); try { controller.Execute(_requestContext); } finally { controllerFactory.ReleaseController(controller); } this.Context.ApplicationInstance.CompleteRequest(); } public void EndProcessRequest(IAsyncResult result) { this.AspCompatEndProcessRequest(result); } public override void ProcessRequest(HttpContext httpContext) { throw new NotSupportedException("STAThreadRouteHandler does not support ProcessRequest called (only BeginProcessRequest)"); } } This handler code figures out which controller to load and then executes the controller. MVC internally provides the information needed to route to the appropriate method and pass the right parameters. Like the Web Service handler the logic occurs in the OnInit() and performs all the processing in that part of the request. Next, we need a RouteHandler that can actually pick up this handler. Unlike the Web Service handler where we simply registered the handler, MVC requires a RouteHandler to pick up the handler. RouteHandlers look at the URL's path and based on that decide on what handler to invoke. The route handler is pretty simple - all it does is load our custom handler: public class MvcStaThreadRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { if (requestContext == null) throw new ArgumentNullException("requestContext"); return new MvcStaThreadHttpAsyncHandler(requestContext); } } At this point you can instantiate this route handler and force STA requests to MVC by specifying a route. The following sets up the ASP.NET Default Route:Route mvcRoute = new Route("{controller}/{action}/{id}", new RouteValueDictionary( new { controller = "Home", action = "Index", id = UrlParameter.Optional }), new MvcStaThreadRouteHandler()); RouteTable.Routes.Add(mvcRoute);   To make this code a little easier to work with and mimic the behavior of the routes.MapRoute() functionality extension method that MVC provides, here is an extension method for MapMvcStaRoute(): public static class RouteCollectionExtensions { public static void MapMvcStaRoute(this RouteCollection routeTable, string name, string url, object defaults = null) { Route mvcRoute = new Route(url, new RouteValueDictionary(defaults), new MvcStaThreadRouteHandler()); RouteTable.Routes.Add(mvcRoute); } } With this the syntax to add  route becomes a little easier and matches the MapRoute() method:RouteTable.Routes.MapMvcStaRoute( name: "Default", url: "{controller}/{action}/{id}", defaults: new { controller = "Home", action = "Index", id = UrlParameter.Optional } ); The nice thing about this route handler, STA Handler and extension method is that it's fully self contained. You can put all three into a single class file and stick it into your Web app, and then simply call MapMvcStaRoute() and it just works. Easy! To see whether this works create an MVC controller like this: public class ThreadTestController : Controller { public string ThreadingMode() { return Thread.CurrentThread.GetApartmentState().ToString(); } } Try this test both with only the MapRoute() hookup in the RouteConfiguration in which case you should get MTA as the value. Then change the MapRoute() call to MapMvcStaRoute() leaving all the parameters the same and re-run the request. You now should see STA as the result. You're on your way using STA COM components reliably in ASP.NET MVC. WCF Web Services running through IIS WCF Web Services provide a more robust and wider range of services for Web Services. You can use WCF over HTTP, TCP, and Pipes, and WCF services support WS* secure services. There are many features in WCF that go way beyond what ASMX can do. But it's also a bit more complex than ASMX. As a basic rule if you need to serve straight SOAP Services over HTTP I 'd recommend sticking with the simpler ASMX services especially if COM is involved. If you need WS* support or want to serve data over non-HTTP protocols then WCF makes more sense. WCF is not my forte but I found a solution from Scott Seely on his blog that describes the progress and that seems to work well. I'm copying his code below so this STA information is all in one place and quickly explain. Scott's code basically works by creating a custom OperationBehavior which can be specified via an [STAOperation] attribute on every method. Using his attribute you end up with a class (or Interface if you separate the contract and class) that looks like this: [ServiceContract] public class WcfService { [OperationContract] public string HelloWorldMta() { return Thread.CurrentThread.GetApartmentState().ToString(); } // Make sure you use this custom STAOperationBehavior // attribute to force STA operation of service methods [STAOperationBehavior] [OperationContract] public string HelloWorldSta() { return Thread.CurrentThread.GetApartmentState().ToString(); } } Pretty straight forward. The latter method returns STA while the former returns MTA. To make STA work every method needs to be marked up. The implementation consists of the attribute and OperationInvoker implementation. Here are the two classes required to make this work from Scott's post:public class STAOperationBehaviorAttribute : Attribute, IOperationBehavior { public void AddBindingParameters(OperationDescription operationDescription, System.ServiceModel.Channels.BindingParameterCollection bindingParameters) { } public void ApplyClientBehavior(OperationDescription operationDescription, System.ServiceModel.Dispatcher.ClientOperation clientOperation) { // If this is applied on the client, well, it just doesn’t make sense. // Don’t throw in case this attribute was applied on the contract // instead of the implementation. } public void ApplyDispatchBehavior(OperationDescription operationDescription, System.ServiceModel.Dispatcher.DispatchOperation dispatchOperation) { // Change the IOperationInvoker for this operation. dispatchOperation.Invoker = new STAOperationInvoker(dispatchOperation.Invoker); } public void Validate(OperationDescription operationDescription) { if (operationDescription.SyncMethod == null) { throw new InvalidOperationException("The STAOperationBehaviorAttribute " + "only works for synchronous method invocations."); } } } public class STAOperationInvoker : IOperationInvoker { IOperationInvoker _innerInvoker; public STAOperationInvoker(IOperationInvoker invoker) { _innerInvoker = invoker; } public object[] AllocateInputs() { return _innerInvoker.AllocateInputs(); } public object Invoke(object instance, object[] inputs, out object[] outputs) { // Create a new, STA thread object[] staOutputs = null; object retval = null; Thread thread = new Thread( delegate() { retval = _innerInvoker.Invoke(instance, inputs, out staOutputs); }); thread.SetApartmentState(ApartmentState.STA); thread.Start(); thread.Join(); outputs = staOutputs; return retval; } public IAsyncResult InvokeBegin(object instance, object[] inputs, AsyncCallback callback, object state) { // We don’t handle async… throw new NotImplementedException(); } public object InvokeEnd(object instance, out object[] outputs, IAsyncResult result) { // We don’t handle async… throw new NotImplementedException(); } public bool IsSynchronous { get { return true; } } } The key in this setup is the Invoker and the Invoke method which creates a new thread and then fires the request on this new thread. Because this approach creates a new thread for every request it's not super efficient. There's a bunch of overhead involved in creating the thread and throwing it away after each thread, but it'll work for low volume requests and insure each thread runs in STA mode. If better performance is required it would be useful to create a custom thread manager that can pool a number of STA threads and hand off threads as needed rather than creating new threads on every request. If your Web Service needs are simple and you need only to serve standard SOAP 1.x requests, I would recommend sticking with ASMX services. It's easier to set up and work with and for STA component use it'll be significantly better performing since ASP.NET manages the STA thread pool for you rather than firing new threads for each request. One nice thing about Scotts code is though that it works in any WCF environment including self hosting. It has no dependency on ASP.NET or WebForms for that matter. STA - If you must STA components are a  pain in the ass and thankfully there isn't too much stuff out there anymore that requires it. But when you need it and you need to access STA functionality from .NET at least there are a few options available to make it happen. Each of these solutions is a bit hacky, but they work - I've used all of them in production with good results with FoxPro components. I hope compiling all of these in one place here makes it STA consumption a little bit easier. I feel your pain :-) Resources Download STA Handler Code Examples Scott Seely's original STA WCF OperationBehavior Article© Rick Strahl, West Wind Technologies, 2005-2012Posted in FoxPro   ASP.NET  .NET  COM   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • why OAuth request_token using openid4java is missing in the google's response?

    - by user454322
    I have succeed using openID and OAuth separately, but I can't make them work together. Am I doing something incorrect: String userSuppliedString = "https://www.google.com/accounts/o8/id"; ConsumerManager manager = new ConsumerManager(); String returnToUrl = "http://example.com:8080/isr-calendar-test-1.0-SNAPSHOT/GAuthorize"; List<DiscoveryInformation> discoveries = manager.discover(userSuppliedString); DiscoveryInformation discovered = manager.associate(discoveries); AuthRequest authReq = manager.authenticate(discovered, returnToUrl); session.put("openID-discoveries", discovered); FetchRequest fetch = FetchRequest.createFetchRequest(); fetch.addAttribute("email","http://schema.openid.net/contact/email",true); fetch.addAttribute("oauth", "http://specs.openid.net/extensions/oauth/1.0",true); fetch.addAttribute("consumer","example.com" ,true); fetch.addAttribute("scope","http://www.google.com/calendar/feeds/" ,true); authReq.addExtension(fetch); destinationUrl = authReq.getDestinationUrl(true); then destinationUrl is https://www.google.com/accounts/o8/ud?openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.claimed_id=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0%2Fidentifier_select&openid.identity=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0%2Fidentifier_select&openid.return_to=http%3A%2F%2Fexample.com%3A8080%2FgoogleTest%2Fauthorize&openid.realm=http%3A%2F%2Fexample.com%3A8080%2FgoogleTest%2Fauthorize&openid.assoc_handle=AMlYA9WVkS_oVNWtczp3zr3sS8lxR4DlnDS0fe-zMIhmepQsByLqvGnc8qeJwypiRQAuQvdw&openid.mode=checkid_setup&openid.ns.ext1=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ext1.mode=fetch_request&openid.ext1.type.email=http%3A%2F%2Fschema.openid.net%2Fcontact%2Femail&openid.ext1.type.oauth=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Foauth%2F1.0&openid.ext1.type.consumer=example.com&openid.ext1.type.scope=http%3A%2F%2Fwww.google.com%2Fcalendar%2Ffeeds%2F&openid.ext1.required=email%2Coauth%2Cconsumer%2Cscope" but in the response from google request_token is missing http://example.com:8080/googleTest/authorize?openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fud&openid.response_nonce=2011-11-29T17%3A38%3A39ZEU2iBVXr_zQG5Q&openid.return_to=http%3A%2F%2Fexample.com%3A8080%2FgoogleTest%2Fauthorize&openid.assoc_handle=AMlYA9WVkS_oVNWtczp3zr3sS8lxR4DlnDS0fe-zMIhmepQsByLqvGnc8qeJwypiRQAuQvdw&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle%2Cns.ext1%2Cext1.mode%2Cext1.type.email%2Cext1.value.email&openid.sig=5jUnS1jT16hIDCAjv%2BwAL1jopo6YHgfZ3nUUgFpeXlw%3D&openid.identity=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fid%3Fid%3DAItOawk8YPjBcnQrqXW8tzK3aFVop63E7q-JrCE&openid.claimed_id=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fid%3Fid%3DAItOawk8YPjBcnQrqXW8tzK3aFVop63E7q-JrCE&openid.ns.ext1=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ext1.mode=fetch_response&openid.ext1.type.email=http%3A%2F%2Fschema.openid.net%2Fcontact%2Femail&openid.ext1.value.email=boxiencosi%40gmail.com why?

    Read the article

  • Django & google openid authentication with socialauth

    - by Zayatzz
    Hello I am trying to use django-socialauth (http://github.com/uswaretech/Django-Socialauth) for authenticating users for my django project. This is firs time working with openid and i've had to figure out how exactly this open id works. I have more or less understood it, by now, but there are few things that elude me. The authentication process starts when the request is put together in in django-socialauth.openid_consumer.views.begin. I can see that the outgoing authentication request is more or less something like this: https://www.google.com/accounts/o8/ud?openid.assoc_handle=AOQobUckRThPUj3K1byG280Aze-dnfc9Iu6AEYaBwvHE11G0zy8kY8GZ& openid.ax.if_available=fname& openid.ax.mode=fetch_request& openid.ax.required=email& openid.ax.type.email=http://axschema.org/contact/email& openid.ax.type.fname=http://example.com/schema/fullname& openid.claimed_id=http://specs.openid.net/auth/2.0/identifier_select& openid.identity=http://specs.openid.net/auth/2.0/identifier_select& openid.mode=checkid_setup&openid.ns=http://specs.openid.net/auth/2.0& openid.ns.ax=http://openid.net/srv/ax/1.0& openid.ns.sreg=http://openid.net/extensions/sreg/1.1& openid.realm=http://localhost/& openid.return_to=http://localhost/social/gmail_login/complete/?janrain_nonce=2010-03-20T11%3A19%3A44ZPZCjNc&openid.sreg.optional=postcode,country,nickname,email This is lot like 2nd example here: http://code.google.com/apis/accounts/docs/OpenID.html#Samples The problem is, that the request, i get back, is nothing like the corresponding example from code.google.com (look at the 3rd example in example responses. Response dict i get is like this: { 'openid.op_endpoint': 'https://www.google.com/accounts/o8/ud', 'openid.sig': 'QWMa4x4ruMUvSCfLwKV6CZRuo0E=', 'openid.ext1.type.email': 'http://axschema.org/contact/email', 'openid.return_to': 'http://localhost/social/gmail_login/complete/?janrain_nonce=2010-03-20T17%3A54%3A06ZHV4cqh', 'janrain_nonce': '2010-03-20T17:54:06ZHV4cqh', 'openid.response_nonce': '2010-03-20T17:54:06ZdC5mMu9M_6O4pw', 'openid.claimed_id': 'https://www.google.com/accounts/o8/id?id=AItOghawkFz0aNzk91vaQWhD-DxRJo6sS09RwM3SE', 'openid.mode': 'id_res', 'openid.ns.ext1': 'http://openid.net/srv/ax/1.0', 'openid.signed': 'op_endpoint,claimed_id,identity,return_to,response_nonce,assoc_handle,ns.ext1,ext1.mode,ext1.type.email,ext1.value.email', 'openid.ext1.value.email': '[email protected]', 'openid.assoc_handle': 'AOQobUfssTJ2IxRlxrIvU4Xg8HHQKKTEuqwGxvwwuPR5rNvag0elGlYL', 'openid.ns': 'http://specs.openid.net/auth/2.0', 'openid.identity': 'https://www.google.com/accounts/o8/id?id=AItOawkghgfhf1FkvaQWhD-DxRJo6sS09RwMKjASE', 'openid.ext1.mode': 'fetch_response'} The socialauth itself has been built to accept my email address this way: elif request.openid and request.openid.ax: email = request.openid.ax.get('email') And obviously this fails. Why i am asking all this is, that perhaps i am doing something wrong and my outgoing request is wrong? Or am i doing all correctly and should change the socialaouth module to accept info in a new way and then commit the change? Alan

    Read the article

  • Django & google openid authentication (openid.ax) with socialauth

    - by Zayatzz
    Hello I am trying to use django-socialauth (http://github.com/uswaretech/Django-Socialauth) for authenticating users for my django project. This is firs time working with openid and i've had to figure out how exactly this open id works. I have more or less understood it, by now, but there are few things that elude me. The authentication process starts when the request is put together in in django-socialauth.openid_consumer.views.begin. I can see that the outgoing authentication request is more or less something like this: https://www.google.com/accounts/o8/ud?openid.assoc_handle=AOQobUckRThPUj3K1byG280Aze-dnfc9Iu6AEYaBwvHE11G0zy8kY8GZ& openid.ax.if_available=fname& openid.ax.mode=fetch_request& openid.ax.required=email& openid.ax.type.email=http://axschema.org/contact/email& openid.ax.type.fname=http://example.com/schema/fullname& openid.claimed_id=http://specs.openid.net/auth/2.0/identifier_select& openid.identity=http://specs.openid.net/auth/2.0/identifier_select& openid.mode=checkid_setup&openid.ns=http://specs.openid.net/auth/2.0& openid.ns.ax=http://openid.net/srv/ax/1.0& openid.ns.sreg=http://openid.net/extensions/sreg/1.1& openid.realm=http://localhost/& openid.return_to=http://localhost/social/gmail_login/complete/?janrain_nonce=2010-03-20T11%3A19%3A44ZPZCjNc&openid.sreg.optional=postcode,country,nickname,email This is lot like 2nd example here: http://code.google.com/apis/accounts/docs/OpenID.html#Samples The problem is, that the request, i get back, is nothing like the corresponding example from code.google.com (look at the 3rd example in example responses. Response dict i get is like this: { 'openid.op_endpoint': 'https://www.google.com/accounts/o8/ud', 'openid.sig': 'QWMa4x4ruMUvSCfLwKV6CZRuo0E=', 'openid.ext1.type.email': 'http://axschema.org/contact/email', 'openid.return_to': 'http://localhost/social/gmail_login/complete/?janrain_nonce=2010-03-20T17%3A54%3A06ZHV4cqh', 'janrain_nonce': '2010-03-20T17:54:06ZHV4cqh', 'openid.response_nonce': '2010-03-20T17:54:06ZdC5mMu9M_6O4pw', 'openid.claimed_id': 'https://www.google.com/accounts/o8/id?id=AItOghawkFz0aNzk91vaQWhD-DxRJo6sS09RwM3SE', 'openid.mode': 'id_res', 'openid.ns.ext1': 'http://openid.net/srv/ax/1.0', 'openid.signed': 'op_endpoint,claimed_id,identity,return_to,response_nonce,assoc_handle,ns.ext1,ext1.mode,ext1.type.email,ext1.value.email', 'openid.ext1.value.email': '[email protected]', 'openid.assoc_handle': 'AOQobUfssTJ2IxRlxrIvU4Xg8HHQKKTEuqwGxvwwuPR5rNvag0elGlYL', 'openid.ns': 'http://specs.openid.net/auth/2.0', 'openid.identity': 'https://www.google.com/accounts/o8/id?id=AItOawkghgfhf1FkvaQWhD-DxRJo6sS09RwMKjASE', 'openid.ext1.mode': 'fetch_response'} The socialauth itself has been built to accept my email address this way: elif request.openid and request.openid.ax: email = request.openid.ax.get('email') And obviously this fails. Why i am asking all this is, that perhaps i am doing something wrong and my outgoing request is wrong? Or am i doing all correctly and should change the socialaouth module to accept info in a new way and then commit the change? Alan

    Read the article

  • How can I keep the cpu temp low?

    - by Newton
    I have an HP pavilion dv7, I'm using ubuntu 12.04 so the overheating problem with sandybridge cpu is a lot better. However my laptop is still becoming too hot to keep on my legs. The problem is that the fan wait too much before starting, so the medium temp is too hight. When I'm using windows 7 the laptop is room-temperature cold, I've absolutely no problem. On windows the fan is always spinning very low & very silently so the heat is continuously removed, without reaching an unconfortable temp. How can I force the computer to act like that also on ubuntu? PS The bios can't let me control this kind of thing, and this is my experience with lm-sensors and fancontrol al@notebook:~$ sudo sensors-detect [sudo] password for al: # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: Hewlett-Packard HP Pavilion dv7 Notebook PC (laptop) # Board: Hewlett-Packard 1800 This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Module cpuid loaded successfully. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... Yes Found unknown chip with ID 0x8518 Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel Cougar Point (PCH) Module i2c-i801 loaded successfully. Module i2c-dev loaded successfully. Next adapter: i915 gmbus disabled (i2c-0) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus ssc (i2c-1) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOB (i2c-2) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus vga (i2c-3) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOA (i2c-4) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus panel (i2c-5) Do you want to scan it? (YES/no/selectively): y Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... No Probing for `EDID EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Next adapter: i915 GPIOC (i2c-6) Do you want to scan it? (YES/no/selectively): y Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... No Probing for `EDID EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Next adapter: i915 gmbus dpc (i2c-7) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOD (i2c-8) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus dpb (i2c-9) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOE (i2c-10) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus reserved (i2c-11) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus dpd (i2c-12) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOF (i2c-13) Do you want to scan it? (YES/no/selectively): y Next adapter: DPDDC-B (i2c-14) Do you want to scan it? (YES/no/selectively): y Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)y Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service module-init-tools start' to load them. Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK al@notebook:~$ sudo /etc/init.d/module-init-tools restart Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service module-init-tools restart Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the stop(8) and then start(8) utilities, e.g. stop module-init-tools ; start module-init-tools. The restart(8) utility is also available. module-init-tools stop/waiting al@notebook:~$ sudo service module-init-tools restart stop: Unknown instance: module-init-tools stop/waiting al@notebook:~$ sudo service module-init-tools start module-init-tools stop/waiting al@notebook:~$ sudo pwmconfig # pwmconfig revision 5857 (2010-08-22) This program will search your sensors for pulse width modulation (pwm) controls, and test each one to see if it controls a fan on your motherboard. Note that many motherboards do not have pwm circuitry installed, even if your sensor chip supports pwm. We will attempt to briefly stop each fan using the pwm controls. The program will attempt to restore each fan to full speed after testing. However, it is ** very important ** that you physically verify that the fans have been to full speed after the program has completed. /usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed Is my case too desperate?

    Read the article

  • Why is Oracle using a skip scan for this query?

    - by Jason Baker
    Here's the tkprof output for a query that's running extremely slowly (WARNING: it's long :-) ): SELECT mbr_comment_idn, mbr_crt_dt, mbr_data_source, mbr_dol_bl_rmo_ind, mbr_dxcg_ctl_member, mbr_employment_start_dt, mbr_employment_term_dt, mbr_entity_active, mbr_ethnicity_idn, mbr_general_health_status_code, mbr_hand_dominant_code, mbr_hgt_feet, mbr_hgt_inches, mbr_highest_edu_level, mbr_insd_addr_idn, mbr_insd_alt_id, mbr_insd_name, mbr_insd_ssn_tin, mbr_is_smoker, mbr_is_vip, mbr_lmbr_first_name, mbr_lmbr_last_name, mbr_marital_status_cd, mbr_mbr_birth_dt, mbr_mbr_death_dt, mbr_mbr_expired, mbr_mbr_first_name, mbr_mbr_gender_cd, mbr_mbr_idn, mbr_mbr_ins_type, mbr_mbr_isreadonly, mbr_mbr_last_name, mbr_mbr_middle_name, mbr_mbr_name, mbr_mbr_status_idn, mbr_mpi_id, mbr_preferred_am_pm, mbr_preferred_time, mbr_prv_innetwork, mbr_rep_addr_idn, mbr_rep_name, mbr_rp_mbr_id, mbr_same_mbr_ins, mbr_special_needs_cd, mbr_timezone, mbr_upd_dt, mbr_user_idn, mbr_wgt, mbr_work_status_idn FROM (SELECT /*+ FIRST_ROWS(1) */ mbr_comment_idn, mbr_crt_dt, mbr_data_source, mbr_dol_bl_rmo_ind, mbr_dxcg_ctl_member, mbr_employment_start_dt, mbr_employment_term_dt, mbr_entity_active, mbr_ethnicity_idn, mbr_general_health_status_code, mbr_hand_dominant_code, mbr_hgt_feet, mbr_hgt_inches, mbr_highest_edu_level, mbr_insd_addr_idn, mbr_insd_alt_id, mbr_insd_name, mbr_insd_ssn_tin, mbr_is_smoker, mbr_is_vip, mbr_lmbr_first_name, mbr_lmbr_last_name, mbr_marital_status_cd, mbr_mbr_birth_dt, mbr_mbr_death_dt, mbr_mbr_expired, mbr_mbr_first_name, mbr_mbr_gender_cd, mbr_mbr_idn, mbr_mbr_ins_type, mbr_mbr_isreadonly, mbr_mbr_last_name, mbr_mbr_middle_name, mbr_mbr_name, mbr_mbr_status_idn, mbr_mpi_id, mbr_preferred_am_pm, mbr_preferred_time, mbr_prv_innetwork, mbr_rep_addr_idn, mbr_rep_name, mbr_rp_mbr_id, mbr_same_mbr_ins, mbr_special_needs_cd, mbr_timezone, mbr_upd_dt, mbr_user_idn, mbr_wgt, mbr_work_status_idn, ROWNUM AS ora_rn FROM (SELECT mbr.comment_idn AS mbr_comment_idn, mbr.crt_dt AS mbr_crt_dt, mbr.data_source AS mbr_data_source, mbr.dol_bl_rmo_ind AS mbr_dol_bl_rmo_ind, mbr.dxcg_ctl_member AS mbr_dxcg_ctl_member, mbr.employment_start_dt AS mbr_employment_start_dt, mbr.employment_term_dt AS mbr_employment_term_dt, mbr.entity_active AS mbr_entity_active, mbr.ethnicity_idn AS mbr_ethnicity_idn, mbr.general_health_status_code AS mbr_general_health_status_code, mbr.hand_dominant_code AS mbr_hand_dominant_code, mbr.hgt_feet AS mbr_hgt_feet, mbr.hgt_inches AS mbr_hgt_inches, mbr.highest_edu_level AS mbr_highest_edu_level, mbr.insd_addr_idn AS mbr_insd_addr_idn, mbr.insd_alt_id AS mbr_insd_alt_id, mbr.insd_name AS mbr_insd_name, mbr.insd_ssn_tin AS mbr_insd_ssn_tin, mbr.is_smoker AS mbr_is_smoker, mbr.is_vip AS mbr_is_vip, mbr.lmbr_first_name AS mbr_lmbr_first_name, mbr.lmbr_last_name AS mbr_lmbr_last_name, mbr.marital_status_cd AS mbr_marital_status_cd, mbr.mbr_birth_dt AS mbr_mbr_birth_dt, mbr.mbr_death_dt AS mbr_mbr_death_dt, mbr.mbr_expired AS mbr_mbr_expired, mbr.mbr_first_name AS mbr_mbr_first_name, mbr.mbr_gender_cd AS mbr_mbr_gender_cd, mbr.mbr_idn AS mbr_mbr_idn, mbr.mbr_ins_type AS mbr_mbr_ins_type, mbr.mbr_isreadonly AS mbr_mbr_isreadonly, mbr.mbr_last_name AS mbr_mbr_last_name, mbr.mbr_middle_name AS mbr_mbr_middle_name, mbr.mbr_name AS mbr_mbr_name, mbr.mbr_status_idn AS mbr_mbr_status_idn, mbr.mpi_id AS mbr_mpi_id, mbr.preferred_am_pm AS mbr_preferred_am_pm, mbr.preferred_time AS mbr_preferred_time, mbr.prv_innetwork AS mbr_prv_innetwork, mbr.rep_addr_idn AS mbr_rep_addr_idn, mbr.rep_name AS mbr_rep_name, mbr.rp_mbr_id AS mbr_rp_mbr_id, mbr.same_mbr_ins AS mbr_same_mbr_ins, mbr.special_needs_cd AS mbr_special_needs_cd, mbr.timezone AS mbr_timezone, mbr.upd_dt AS mbr_upd_dt, mbr.user_idn AS mbr_user_idn, mbr.wgt AS mbr_wgt, mbr.work_status_idn AS mbr_work_status_idn FROM mbr JOIN mbr_identfn ON mbr.mbr_idn = mbr_identfn.mbr_idn WHERE mbr_identfn.mbr_idn = mbr.mbr_idn AND mbr_identfn.identfd_type = :identfd_type_1 AND mbr_identfn.identfd_number = :identfd_number_1 AND mbr_identfn.entity_active = :entity_active_1) WHERE ROWNUM <= :ROWNUM_1) WHERE ora_rn > :ora_rn_1 call count cpu elapsed disk query current rows ------- ------ -------- ---------- ---------- ---------- ---------- ---------- Parse 9936 0.46 0.49 0 0 0 0 Execute 9936 0.60 0.59 0 0 0 0 Fetch 9936 329.87 404.00 0 136966922 0 0 ------- ------ -------- ---------- ---------- ---------- ---------- ---------- total 29808 330.94 405.09 0 136966922 0 0 Misses in library cache during parse: 0 Optimizer mode: FIRST_ROWS Parsing user id: 36 (JIVA_DEV) Rows Row Source Operation ------- --------------------------------------------------- 0 VIEW (cr=102 pr=0 pw=0 time=2180 us) 0 COUNT STOPKEY (cr=102 pr=0 pw=0 time=2163 us) 0 NESTED LOOPS (cr=102 pr=0 pw=0 time=2152 us) 0 INDEX SKIP SCAN IDX_MBR_IDENTFN (cr=102 pr=0 pw=0 time=2140 us)(object id 341053) 0 TABLE ACCESS BY INDEX ROWID MBR (cr=0 pr=0 pw=0 time=0 us) 0 INDEX UNIQUE SCAN PK_CLAIMANT (cr=0 pr=0 pw=0 time=0 us)(object id 334044) Rows Execution Plan ------- --------------------------------------------------- 0 SELECT STATEMENT MODE: HINT: FIRST_ROWS 0 VIEW 0 COUNT (STOPKEY) 0 NESTED LOOPS 0 INDEX MODE: ANALYZED (SKIP SCAN) OF 'IDX_MBR_IDENTFN' (INDEX (UNIQUE)) 0 TABLE ACCESS MODE: ANALYZED (BY INDEX ROWID) OF 'MBR' (TABLE) 0 INDEX MODE: ANALYZED (UNIQUE SCAN) OF 'PK_CLAIMANT' (INDEX (UNIQUE)) ******************************************************************************** Based on my reading of Oracle's documentation of skip scans, a skip scan is most useful when the first column of an index has a low number of unique values. The thing is that the first index of this column is a unique primary key. So am I correct in assuming that a skip scan is the wrong thing to do here? Also, what kind of scan should it be doing? Should I do some more hinting for this query? EDIT: I should also point out that the query's where clause uses the columns in IDX_MBR_IDENTFN and no columns other than what's in that index. So as far as I can tell, I'm not skipping any columns.

    Read the article

  • Dell Studio 1737 Overheating

    - by Sean
    I am using a Dell Studio 1737 laptop. I have been running Linux and have ran Windows recently for a very long time. I upgraded to the 10.10 distribution and since that distro, it seems that for some reason all Linuxes want to push my laptop to extremes. I have recently upgraded to Ubuntu 12.04 since I heart that it contains kernel fixes for overheating issues. 12.04 will actually eventually cool the system, but that is after the fans run to the point it sounds like a jet aircraft taking off and the laptop makes my hands sweat. In trying to combat the heat problems I have done the following: I installed the propriatery driver for my ATI Mobility HD 3600. I have tried both the one in the Additional Drivers and also tried ATI's latest greatest version. If I don't install this my laptop will overheat and shut off in minutes. Both seem to perform similarly, but the heat problem remains. I have tried limiting the CPU by installing the CPUFreq Indicator. This does help keep the machine from shutting off, but the heat is still uncomfortable to be around the machine. I usually run in power saver mode or run the cpu at 1.6 GHZ just to error on safety. I ran sensors-detect and here are the results: sean@sean-Studio-1737:~$ sudo sensors-detect # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: Dell Inc. Studio 1737 (laptop) # Board: Dell Inc. 0F237N This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Module cpuid loaded successfully. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... Yes Found `ITE IT8512E/F/G Super IO' (but not activated) Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel ICH9 Module i2c-i801 loaded successfully. Module i2c-dev loaded successfully. Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)y Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service module-init-tools start' to load them. Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK sean@sean-Studio-1737:~$ sudo service module-init-tools start module-init-tools stop/waiting I also tried installing i8k but that didn't work since it didn't seem to be able to communicate with the hardware (probably for different kind of device). Also I ran acpi -V and here are the results: Battery 0: Full, 100% Battery 0: design capacity 613 mAh, last full capacity 260 mAh = 42% Adapter 0: on-line Thermal 0: ok, 49.0 degrees C Thermal 0: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 1: ok, 48.0 degrees C Thermal 1: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 2: ok, 51.0 degrees C Thermal 2: trip point 0 switches to mode critical at temperature 100.0 degrees C Cooling 0: LCD 0 of 15 Cooling 1: Processor 0 of 10 Cooling 2: Processor 0 of 10 I have hit a wall and don't know what to do now. Any advice is appreciated.

    Read the article

  • Can I someone point to me what I did wrong? Trying to map VB to Java using JNA to access the library

    - by henry
    Original Working VB_Code Private Declare Function ConnectReader Lib "rfidhid.dll" () As Integer Private Declare Function DisconnectReader Lib "rfidhid.dll" () As Integer Private Declare Function SetAntenna Lib "rfidhid.dll" (ByVal mode As Integer) As Integer Private Declare Function Inventory Lib "rfidhid.dll" (ByRef tagdata As Byte, ByVal mode As Integer, ByRef taglen As Integer) As Integer Private Sub Form1_Load(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles MyBase.Load Dim desc As String desc = "1. Click ""Connect"" to talk to reader." & vbCr & vbCr desc &= "2. Click ""RF On"" to wake up the TAG." & vbCr & vbCr desc &= "3. Click ""Read Tag"" to get tag PCEPC." lblDesc.Text = desc End Sub Private Sub cmdConnect_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles cmdConnect.Click If cmdConnect.Text = "Connect" Then If ConnectReader() Then cmdConnect.Text = "Disconnect" Else MsgBox("Unable to connect to RFID Reader. Please check reader connection.") End If Else If DisconnectReader() Then cmdConnect.Text = "Connect" End If End If End Sub Private Sub cmdRF_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles cmdRF.Click If cmdRF.Text = "RF On" Then If SetAntenna(&HFF) Then cmdRF.Text = "RF Off" End If Else If SetAntenna(&H0) Then cmdRF.Text = "RF On" End If End If End Sub Private Sub cmdReadTag_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles cmdReadTag.Click Dim tagdata(64) As Byte Dim taglen As Integer, cnt As Integer Dim pcepc As String pcepc = "" If Inventory(tagdata(0), 1, taglen) Then For cnt = 0 To taglen - 1 pcepc &= tagdata(cnt).ToString("X2") Next txtPCEPC.Text = pcepc Else txtPCEPC.Text = "ReadError" End If End Sub Java Code (Simplified) import com.sun.jna.Library; import com.sun.jna.Native; public class HelloWorld { public interface MyLibrary extends Library { public int ConnectReader(); public int SetAntenna (int mode); public int Inventory (byte tagdata, int mode, int taglen); } public static void main(String[] args) { MyLibrary lib = (MyLibrary) Native.loadLibrary("rfidhid", MyLibrary.class); System.out.println(lib.ConnectReader()); System.out.println(lib.SetAntenna(255)); byte[] tagdata = new byte[64]; int taglen = 0; int cnt; String pcepc; pcepc = ""; if (lib.Inventory(tagdata[0], 1, taglen) == 1) { for (cnt = 0; cnt < taglen; cnt++) pcepc += String.valueOf(tagdata[cnt]); } } } The error happens when lib.Inventory is run. lib.Inventory is used to get the tag from the RFID reader. If there is no tag, no error. The error code An unexpected error has been detected by Java Runtime Environment: EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x0b1d41ab, pid=5744, tid=4584 Java VM: Java HotSpot(TM) Client VM (11.2-b01 mixed mode windows-x86) Problematic frame: C [rfidhid.dll+0x141ab] An error report file with more information is saved as: C:\eclipse\workspace\FelmiReader\hs_err_pid5744.log

    Read the article

  • Real tortoises keep it slow and steady. How about the backups?

    - by Maria Zakourdaev
      … Four tortoises were playing in the backyard when they decided they needed hibiscus flower snacks. They pooled their money and sent the smallest tortoise out to fetch the snacks. Two days passed and there was no sign of the tortoise. "You know, she is taking a lot of time", said one of the tortoises. A little voice from just out side the fence said, "If you are going to talk that way about me I won't go." Is it too much to request from the quite expensive 3rd party backup tool to be a way faster than the SQL server native backup? Or at least save a respectable amount of storage by producing a really smaller backup files?  By saying “really smaller”, I mean at least getting a file in half size. After Googling the internet in an attempt to understand what other “sql people” are using for database backups, I see that most people are using one of three tools which are the main players in SQL backup area:  LiteSpeed by Quest SQL Backup by Red Gate SQL Safe by Idera The feedbacks about those tools are truly emotional and happy. However, while reading the forums and blogs I have wondered, is it possible that many are accustomed to using the above tools since SQL 2000 and 2005.  This can easily be understood due to the fact that a 300GB database backup for instance, using regular a SQL 2005 backup statement would have run for about 3 hours and have produced ~150GB file (depending on the content, of course).  Then you take a 3rd party tool which performs the same backup in 30 minutes resulting in a 30GB file leaving you speechless, you run to management persuading them to buy it due to the fact that it is definitely worth the price. In addition to the increased speed and disk space savings you would also get backup file encryption and virtual restore -  features that are still missing from the SQL server. But in case you, as well as me, don’t need these additional features and only want a tool that performs a full backup MUCH faster AND produces a far smaller backup file (like the gain you observed back in SQL 2005 days) you will be quite disappointed. SQL Server backup compression feature has totally changed the market picture. Medium size database. Take a look at the table below, check out how my SQL server 2008 R2 compares to other tools when backing up a 300GB database. It appears that when talking about the backup speed, SQL 2008 R2 compresses and performs backup in similar overall times as all three other tools. 3rd party tools maximum compression level takes twice longer. Backup file gain is not that impressive, except the highest compression levels but the price that you pay is very high cpu load and much longer time. Only SQL Safe by Idera was quite fast with it’s maximum compression level but most of the run time have used 95% cpu on the server. Note that I have used two types of destination storage, SATA 11 disks and FC 53 disks and, obviously, on faster storage have got my backup ready in half time. Looking at the above results, should we spend money, bother with another layer of complexity and software middle-man for the medium sized databases? I’m definitely not going to do so.  Very large database As a next phase of this benchmark, I have moved to a 6 terabyte database which was actually my main backup target. Note, how multiple files usage enables the SQL Server backup operation to use parallel I/O and remarkably increases it’s speed, especially when the backup device is heavily striped. SQL Server supports a maximum of 64 backup devices for a single backup operation but the most speed is gained when using one file per CPU, in the case above 8 files for a 2 Quad CPU server. The impact of additional files is minimal.  However, SQLsafe doesn’t show any speed improvement between 4 files and 8 files. Of course, with such huge databases every half percent of the compression transforms into the noticeable numbers. Saving almost 470GB of space may turn the backup tool into quite valuable purchase. Still, the backup speed and high CPU are the variables that should be taken into the consideration. As for us, the backup speed is more critical than the storage and we cannot allow a production server to sustain 95% cpu for such a long time. Bottomline, 3rd party backup tool developers, we are waiting for some breakthrough release. There are a few unanswered questions, like the restore speed comparison between different tools and the impact of multiple backup files on restore operation. Stay tuned for the next benchmarks.    Benchmark server: SQL Server 2008 R2 sp1 2 Quad CPU Database location: NetApp FC 15K Aggregate 53 discs Backup statements: No matter how good that UI is, we need to run the backup tasks from inside of SQL Server Agent to make sure they are covered by our monitoring systems. I have used extended stored procedures (command line execution also is an option, I haven’t noticed any impact on the backup performance). SQL backup LiteSpeed SQL Backup SQL safe backup database <DBNAME> to disk= '\\<networkpath>\par1.bak' , disk= '\\<networkpath>\par2.bak', disk= '\\<networkpath>\par3.bak' with format, compression EXECUTE master.dbo.xp_backup_database @database = N'<DBName>', @backupname= N'<DBName> full backup', @desc = N'Test', @compressionlevel=8, @filename= N'\\<networkpath>\par1.bak', @filename= N'\\<networkpath>\par2.bak', @filename= N'\\<networkpath>\par3.bak', @init = 1 EXECUTE master.dbo.sqlbackup '-SQL "BACKUP DATABASE <DBNAME> TO DISK= ''\\<networkpath>\par1.sqb'', DISK= ''\\<networkpath>\par2.sqb'', DISK= ''\\<networkpath>\par3.sqb'' WITH DISKRETRYINTERVAL = 30, DISKRETRYCOUNT = 10, COMPRESSION = 4, INIT"' EXECUTE master.dbo.xp_ss_backup @database = 'UCMSDB', @filename = '\\<networkpath>\par1.bak', @backuptype = 'Full', @compressionlevel = 4, @backupfile = '\\<networkpath>\par2.bak', @backupfile = '\\<networkpath>\par3.bak' If you still insist on using 3rd party tools for the backups in your production environment with maximum compression level, you will definitely need to consider limiting cpu usage which will increase the backup operation time even more: RedGate : use THREADPRIORITY option ( values 0 – 6 ) LiteSpeed : use  @throttle ( percentage, like 70%) SQL safe :  the only thing I have found was @Threads option.   Yours, Maria

    Read the article

  • &lt;%: %&gt;, HtmlEncode, IHtmlString and MvcHtmlString

    - by Shaun
    One of my colleague and friend, Robin is playing and struggling with the ASP.NET MVC 2 on a project these days while I’m struggling with a annoying client. Since it’s his first time to use ASP.NET MVC he was meetings with a lot of problem and I was very happy to share my experience to him. Yesterday he asked me when he attempted to insert a <br /> element into his page he found that the page was rendered like this which is bad. He found his <br /> was shown as a part of the string rather than creating a new line. After checked a bit in his code I found that it’s because he utilized a new ASP.NET markup supported in .NET 4.0 – “<%: %>”. If you have been using ASP.NET MVC 1 or in .NET 3.5 world it would be very common that using <%= %> to show something on the page from the backend code. But when you do it you must ensure that the string that are going to be displayed should be Html-safe, which means all the Html markups must be encoded. Otherwise this might cause an XSS (cross-site scripting) problem. So that you’d better use the code like this below to display anything on the page. In .NET 4.0 Microsoft introduced a new markup to solve this problem which is <%: %>. It will encode the content automatically so that you will no need to check and verify your code manually for the XSS issue mentioned below. But this also means that it will encode all things, include the Html element you want to be rendered. So I changed his code like this and it worked well. After helped him solved this problem and finished a spreadsheet for my boring project I considered a bit more on the <%: %>. Since it will encode all thing why it renders correctly when we use “<%: Html.TextBox(“name”) %>” to show a text box? As you know the Html.TextBox will render a “<input name="name" id="name" type="text"/>” element on the page. If <%: %> will encode everything it should not display a text box. So I dig into the source code of the MVC and found some comments in the class MvcHtmlString. 1: // In ASP.NET 4, a new syntax <%: %> is being introduced in WebForms pages, where <%: expression %> is equivalent to 2: // <%= HttpUtility.HtmlEncode(expression) %>. The intent of this is to reduce common causes of XSS vulnerabilities 3: // in WebForms pages (WebForms views in the case of MVC). This involves the addition of an interface 4: // System.Web.IHtmlString and a static method overload System.Web.HttpUtility::HtmlEncode(object). The interface 5: // definition is roughly: 6: // public interface IHtmlString { 7: // string ToHtmlString(); 8: // } 9: // And the HtmlEncode(object) logic is roughly: 10: // - If the input argument is an IHtmlString, return argument.ToHtmlString(), 11: // - Otherwise, return HtmlEncode(Convert.ToString(argument)). 12: // 13: // Unfortunately this has the effect that calling <%: Html.SomeHelper() %> in an MVC application running on .NET 4 14: // will end up encoding output that is already HTML-safe. As a result, we're changing out HTML helpers to return 15: // MvcHtmlString where appropriate. <%= Html.SomeHelper() %> will continue to work in both .NET 3.5 and .NET 4, but 16: // changing the return types to MvcHtmlString has the added benefit that <%: Html.SomeHelper() %> will also work 17: // properly in .NET 4 rather than resulting in a double-encoded output. MVC developers in .NET 4 will then be able 18: // to use the <%: %> syntax almost everywhere instead of having to remember where to use <%= %> and where to use 19: // <%: %>. This should help developers craft more secure web applications by default. 20: // 21: // To create an MvcHtmlString, use the static Create() method instead of calling the protected constructor. The comment said the encoding rule of the <%: %> would be: If the type of the content is IHtmlString it will NOT encode since the IHtmlString indicates that it’s Html-safe. Otherwise it will use HtmlEncode to encode the content. If we check the return type of the Html.TextBox method we will find that it’s MvcHtmlString, which was implemented the IHtmlString interface dynamically. That is the reason why the “<input name="name" id="name" type="text"/>” was not encoded by <%: %>. So if we want to tell ASP.NET MVC, or I should say the ASP.NET runtime that the content is Html-safe and no need, or should not be encoded we can convert the content into IHtmlString. So another resolution would be like this. Also we can create an extension method as well for better developing experience. 1: using System; 2: using System.Collections.Generic; 3: using System.Linq; 4: using System.Web; 5: using System.Web.Mvc; 6:  7: namespace ShaunXu.Blogs.IHtmlStringIssue 8: { 9: public static class Helpers 10: { 11: public static MvcHtmlString IsHtmlSafe(this string content) 12: { 13: return MvcHtmlString.Create(content); 14: } 15: } 16: } Then the view would be like this. And the page rendered correctly.         Summary In this post I explained a bit about the new markup in .NET 4.0 – <%: %> and its usage. I also explained a bit about how to control the page content, whether it should be encoded or not. We can see the ASP.NET MVC gives us more points to control the web pages.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

    Read the article

  • Hive metadata permission issue

    - by Chandramohan
    We are getting this error on Hive, while creating a DB / table hive> CREATE TABLE pokes (foo INT, bar STRING); FAILED: Error in metadata: javax.jdo.JDOFatalDataStoreException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. NestedThrowables: org.apache.commons.dbcp.SQLNestedException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. FAILED: Execution Error, return code 1 from org.apache.hadoop.hive.ql.exec.DDLTask Hive log : org.apache.commons.dbcp.SQLNestedException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. at org.datanucleus.jdo.NucleusJDOHelper.getJDOExceptionForNucleusException(NucleusJDOHelper.java:298) at org.datanucleus.jdo.JDOPersistenceManagerFactory.freezeConfiguration(JDOPersistenceManagerFactory.java:601) at org.datanucleus.jdo.JDOPersistenceManagerFactory.createPersistenceManagerFactory(JDOPersistenceManagerFactory.java:286) at org.datanucleus.jdo.JDOPersistenceManagerFactory.getPersistenceManagerFactory(JDOPersistenceManagerFactory.java:182) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at javax.jdo.JDOHelper$16.run(JDOHelper.java:1958) at java.security.AccessController.doPrivileged(Native Method) at javax.jdo.JDOHelper.invoke(JDOHelper.java:1953) at javax.jdo.JDOHelper.invokeGetPersistenceManagerFactoryOnImplementation(JDOHelper.java:1159) at javax.jdo.JDOHelper.getPersistenceManagerFactory(JDOHelper.java:803) at javax.jdo.JDOHelper.getPersistenceManagerFactory(JDOHelper.java:698) at org.apache.hadoop.hive.metastore.ObjectStore.getPMF(ObjectStore.java:234) at org.apache.hadoop.hive.metastore.ObjectStore.getPersistenceManager(ObjectStore.java:261) at org.apache.hadoop.hive.metastore.ObjectStore.initialize(ObjectStore.java:196) at org.apache.hadoop.hive.metastore.ObjectStore.setConf(ObjectStore.java:171) at org.apache.hadoop.util.ReflectionUtils.setConf(ReflectionUtils.java:62) at org.apache.hadoop.util.ReflectionUtils.newInstance(ReflectionUtils.java:117) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.getMS(HiveMetaStore.java:354) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.executeWithRetry(HiveMetaStore.java:306) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.createDefaultDB(HiveMetaStore.java:451) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.init(HiveMetaStore.java:232) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.<init>(HiveMetaStore.java:197) at org.apache.hadoop.hive.metastore.HiveMetaStoreClient.<init>(HiveMetaStoreClient.java:108) at org.apache.hadoop.hive.ql.metadata.Hive.createMetaStoreClient(Hive.java:1868) at org.apache.hadoop.hive.ql.metadata.Hive.getMSC(Hive.java:1878) at org.apache.hadoop.hive.ql.metadata.Hive.createTable(Hive.java:470) ... 15 more Caused by: org.apache.commons.dbcp.SQLNestedException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. at org.apache.commons.dbcp.PoolingDataSource.getConnection(PoolingDataSource.java:114) at org.datanucleus.store.rdbms.ConnectionFactoryImpl$ManagedConnectionImpl.getConnection(ConnectionFactoryImpl.java:521) at org.datanucleus.store.rdbms.RDBMSStoreManager.<init>(RDBMSStoreManager.java:290) at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at org.datanucleus.plugin.NonManagedPluginRegistry.createExecutableExtension(NonManagedPluginRegistry.java:588) at org.datanucleus.plugin.PluginManager.createExecutableExtension(PluginManager.java:300) at org.datanucleus.ObjectManagerFactoryImpl.initialiseStoreManager(ObjectManagerFactoryImpl.java:161) at org.datanucleus.jdo.JDOPersistenceManagerFactory.freezeConfiguration(JDOPersistenceManagerFactory.java:583) ... 42 more Caused by: java.util.NoSuchElementException: Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. at org.apache.commons.pool.impl.GenericObjectPool.borrowObject(GenericObjectPool.java:1191) at org.apache.commons.dbcp.PoolingDataSource.getConnection(PoolingDataSource.java:106) ... 52 more 2011-08-11 18:02:36,964 ERROR ql.Driver (SessionState.java:printError(343)) - FAILED: Execution Error, return code 1 from org.apache.hadoop.hive.ql.exec.DDLTask

    Read the article

  • proftpd, dynamic IP, and filezilla: port troubles

    - by Yami
    The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

    Read the article

  • Xen kernel can't see 2 disks of 6 of 1TB, does it have a limitation?

    - by PartySoft
    Linux gentoo-xen 2.6.18-xen-r12 #3 SMP Tue Oct 5 09:28:53 PDT 2010 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux I have 6 disks of 1 TB and i can't see all of them only 4, can anyone give me an ideea what can i do ? Filesystem Size Used Avail Use% Mounted on rootfs 886G 4.4G 836G 1% / /dev/sda3 886G 4.4G 836G 1% / rc-svcdir 1.0M 44K 980K 5% /lib64/rc/init.d shm 7.9G 0 7.9G 0% /dev/shm /dev/sdb1 917G 200M 871G 1% /home2 /dev/sdc1 917G 200M 871G 1% /home3 /dev/sdd1 917G 200M 871G 1% /home4 The hardware is Dual xeon E5506 processors on a supermicro X8DTL mobo 4.346585] ata3.00: ATA-8, max UDMA/133, 1953525168 sectors: LBA48 NCQ (depth 0/32) [ 4.346588] ata3.00: ata3: dev 0 multi count 16 [ 4.352861] ata3.00: configured for UDMA/133 [ 4.352867] scsi3 : ata_piix [ 4.352875] PM: Adding info for No Bus:host3 [ 4.510584] ata4.00: ATA-8, max UDMA/133, 1953525168 sectors: LBA48 NCQ (depth 0/32) [ 4.510587] ata4.00: ata4: dev 0 multi count 16 [ 4.516848] ata4.00: configured for UDMA/133 [ 4.516861] PM: Adding info for No Bus:target2:0:0 [ 4.516905] Vendor: ATA Model: SAMSUNG HD103SJ Rev: 1AJ1 [ 4.516910] Type: Direct-Access ANSI SCSI revision: 05 [ 4.516920] PM: Adding info for scsi:2:0:0:0 [ 4.517452] SCSI device sde: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.517460] sde: Write Protect is off [ 4.517461] sde: Mode Sense: 00 3a 00 00 [ 4.517478] SCSI device sde: drive cache: write back [ 4.517514] SCSI device sde: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.517521] sde: Write Protect is off [ 4.517522] sde: Mode Sense: 00 3a 00 00 [ 4.517532] SCSI device sde: drive cache: write back [ 4.517534] sde: sde1 [ 4.524551] sd 2:0:0:0: Attached scsi disk sde [ 4.524855] sd 2:0:0:0: Attached scsi generic sg4 type 0 [ 4.524874] PM: Adding info for No Bus:target3:0:0 [ 4.524928] Vendor: ATA Model: SAMSUNG HD103SJ Rev: 1AJ1 [ 4.524933] Type: Direct-Access ANSI SCSI revision: 05 [ 4.524946] PM: Adding info for scsi:3:0:0:0 [ 4.525216] SCSI device sdf: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.525227] sdf: Write Protect is off [ 4.525228] sdf: Mode Sense: 00 3a 00 00 [ 4.525242] SCSI device sdf: drive cache: write back [ 4.525280] SCSI device sdf: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.525286] sdf: Write Protect is off [ 4.525289] sdf: Mode Sense: 00 3a 00 00 [ 4.525301] SCSI device sdf: drive cache: write back [ 4.525302] sdf: sdf1 [ 4.532691] sd 3:0:0:0: Attached scsi disk sdf [ 4.533010] sd 3:0:0:0: Attached scsi generic sg5 type 0 [ 4.977669] scsi: <fdomain> Detection failed (no card) [ 5.030479] GDT-HA: Storage RAID Controller Driver. Version: 3.05 [ 5.030635] GDT-HA: Found 0 PCI Storage RAID Controllers [ 5.372350] Fusion MPT base driver 3.04.01 [ 5.372358] Copyright (c) 1999-2005 LSI Logic Corporation [ 5.579176] Fusion MPT SPI Host driver 3.04.01 [ 5.881777] ieee1394: Initialized config rom entry `ip1394' [ 6.166745] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 6.166748] ieee1394: sbp2: Try serialize_io=0 for better performance [ 6.428866] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [ 6.428872] md: bitmap version 4.39 [ 6.431518] md: raid0 personality registered for level 0 [ 6.495979] md: raid1 personality registered for level 1 [ 6.570270] raid5: automatically using best checksumming function: generic_sse [ 6.575523] generic_sse: 6608.000 MB/sec [ 6.575526] raid5: using function: generic_sse (6608.000 MB/sec) [ 6.596226] raid6: int64x1 1835 MB/s [ 6.613231] raid6: int64x2 1773 MB/s [ 6.630256] raid6: int64x4 1675 MB/s [ 6.647296] raid6: int64x8 1027 MB/s [ 6.664267] raid6: sse2x1 3578 MB/s [ 6.681268] raid6: sse2x2 4207 MB/s [ 6.698280] raid6: sse2x4 4625 MB/s [ 6.698281] raid6: using algorithm sse2x4 (4625 MB/s) [ 6.698285] md: raid6 personality registered for level 6 [ 6.698286] md: raid5 personality registered for level 5 [ 6.698288] md: raid4 personality registered for level 4 [ 6.781090] md: raid10 personality registered for level 10 [ 7.007043] Intel(R) PRO/1000 Network Driver - version 7.1.9-k4 [ 7.007046] Copyright (c) 1999-2006 Intel Corporation. [ 9.229465] kjournald starting. Commit interval 5 seconds [ 9.229476] EXT3-fs: mounted filesystem with ordered data mode.

    Read the article

  • Uncovering Compiler Errors in ASP.NET MVC Views

    - by Ben Griswold
    ASPX and ASCX files are compiled on the fly when they are requested on the web server. This means it’s possible that you aren’t catching compile errors associated with your views when you build your ASP.NET MVC project in Visual Studio.  Unless you’re willing to click through your entire application, rendering each view looking for errors, you application is left a little vulnerable to user issues.  Fortunately, there’s a work around.  Open up your MVC project file in notepad or within the Visual Studio IDE by unloading the project and then editing the .csproj file (both actions are available by right-clicking on the Project Node in Solution Explorer.)  Notice the MvcBuildViews option.  It’s probably set to false.  Flip the value to true and you’ll magically start compiling your views when you build your application. <MvcBuildViews>false</MvcBuildViews> Taking this action will slow down your builds a bit, but if you’re a hack like me, it’ll probably save your day in the long run. Now you’re probably thinking, “Neat trick – how’s it work?”  Scroll down toward the bottom of your csproj file and you will notice the AfterBuild target triggers the AspNetCompiler action if the MvcBuildViews option is set to true.  <Target Name="AfterBuild" Condition="'$(MvcBuildViews)'=='true'">   <AspNetCompiler VirtualPath="temp"                   PhysicalPath="$(ProjectDir)\..\$(ProjectName)" /> </Target> Great. One more thing. Let’s say you don’t want to slow down all of your builds, but you absolutely want to know if there are any compiler issues with your views before you commit your code to version control or deploy or whatever.  Here’s what you can do – change the AfterBuild condition to run if your configuration is set to Release mode.  <Target Name="AfterBuild" Condition="'$(Configuration)'=='Release'">   <!– Always pre-compile ASPX and ASCX in release mode –>   <AspNetCompiler VirtualPath="temp"                   PhysicalPath="$(ProjectDir)\..\$(ProjectName)" /> </Target> Now your debug mode builds will continue to be as fast as ever and you can quickly validate your views by building in release mode when you so choose.  There’s one little catch – this setup won’t consider the MvcBuildViews option whatsoever! So if you decide to go with this configuration, you might want to add a comment near the MvcBuildViews option letting other developers know they can change the MvcBuildViews option as much as they’d like but it’s not going to affect the AfterBuild action.  Or don’t include the comment and let your team members figure it out for themselves…

    Read the article

  • Install GIMP 2.7.1 on Lucid Lynx using PPA

    - by Vivek
    GIMP lovers are going to be disappointed to hear that GIMP is going away in the next release of much awaited Ubuntu 10.04. Today we take a look at installing in on Lucid Lynx using PPA. The reason for getting rid of it as cited by the GIMP developers, is that GIMP is too professional a software to be included in regular desktop version of Ubuntu. And it takes up too much of space on the disk. Also, the fact that it’s too complicated for regular users. If you can’t live without it…let’s see how to install GIMP 2.7.1 on Lucid Lynx (Currently in Alpha). The new version of GIMP supports single window mode and we will also see how to enable this feature as well. First we need to add the official GIMP 2.7.1 PPA in the software sources of Ubuntu 10.04, by opening the terminal window and typing the following command: sudo sh -c “echo ‘deb http://ppa.launchpad.net/matthaeus123/mrw-gimp-svn/ubuntu lucid main’ >> /etc/apt/sources.list” Now that we have added the PPA we need to add the GPG key, so type the following in your Terminal window. sudo apt-key adv –recv-keys –keyserver keyserver.ubuntu.com 405A15CB Next up we have to update the software repository… sudo apt-get update All that is left is to install GIMP 2.7.1 by typing in the following… sudo apt-get install gimp Click ‘Y’ (for yes) to install GIMP Once GIMP is installed you can start it by going to Applications > Graphics > GNU Image Manipulation Program. You now have your favorite GIMP on your favorite Ubuntu 10.04. As you can see in the image below, GIMP still comes with default 3 windows, which could clog up your lower panel In Ubuntu 10.04. However, now you can run GIMP in single window mode by going to Windows > Single-Window mode. That’s all! Now you have your GIMP running in single window mode with less of hassle to manage 3 windows. It’s unfortunate that GIMP will not be included, but by following these instructions, you’ll be able to enjoy using it in Ubuntu 10.04. Similar Articles Productive Geek Tips Show the List of Installed Packages on Ubuntu or DebianHow to Install Windows Applications on Linux Using CrossoverInstall VMware Tools on Ubuntu Edgy EftInstall Adobe PDF Reader on Ubuntu EdgyInstall MySQL Server 4.1 on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Stretch popurls.com with a Stylish Script (Firefox) OldTvShows.org – Find episodes of Hitchcock, Soaps, Game Shows and more Download Microsoft Office Help tab The Growth of Citibank Quickly Switch between Tabs in IE Windows Media Player 12: Tweak Video & Sound with Playback Enhancements

    Read the article

  • IPS Facets and Info files

    - by mkupfer
    One of the unusual things about IPS is its "facet" feature. For example, if you're a developer using the foo library, you don't install a libfoo-dev package to get the header files. Intead, you install the libfoo package, and your facet.devel setting controls whether you get header files. I was reminded of this recently when I tried to look at some documentation for Emacs Org mode. I was surprised when Emacs's Info browser said it couldn't find the top-level Info directory. I poked around in /usr/share but couldn't find any info files. $ ls -l /usr/share/info ls: cannot access /usr/share/info: No such file or directory Was I was missing a package? $ pkg list -a | egrep "info|emacs" editor/gnu-emacs 23.1-0.175.0.0.0.2.537 i-- editor/gnu-emacs/gnu-emacs-gtk 23.1-0.175.0.0.0.2.537 i-- editor/gnu-emacs/gnu-emacs-lisp 23.1-0.175.0.0.0.2.537 --- editor/gnu-emacs/gnu-emacs-no-x11 23.1-0.175.0.0.0.2.537 --- editor/gnu-emacs/gnu-emacs-x11 23.1-0.175.0.0.0.2.537 i-- system/data/terminfo 0.5.11-0.175.0.0.0.2.1 i-- system/data/terminfo/terminfo-core 0.5.11-0.175.0.0.0.2.1 i-- text/texinfo 4.7-0.175.0.0.0.2.537 i-- x11/diagnostic/x11-info-clients 7.6-0.175.0.0.0.0.1215 i-- $ Hmm. I didn't have the gnu-emacs-lisp package. That seemed an unlikely place to stick the Info files, and pkg(1) confirmed that the info files were not there: $ pkg contents -r gnu-emacs-lisp | grep info usr/share/emacs/23.1/lisp/info-look.el.gz usr/share/emacs/23.1/lisp/info-xref.el.gz usr/share/emacs/23.1/lisp/info.el.gz usr/share/emacs/23.1/lisp/informat.el.gz usr/share/emacs/23.1/lisp/org/org-info.el.gz usr/share/emacs/23.1/lisp/org/org-jsinfo.el.gz usr/share/emacs/23.1/lisp/pcvs-info.el.gz usr/share/emacs/23.1/lisp/textmodes/makeinfo.el.gz usr/share/emacs/23.1/lisp/textmodes/texinfo.el.gz $ Well, if I have what look like the right packages but don't have the right files, the next thing to check are the facets. The first check is whether there is a facet associated with the Info files: $ pkg contents -m gnu-emacs | grep usr/share/info dir facet.doc.info=true group=bin mode=0755 owner=root path=usr/share/info file [...] chash=[...] facet.doc.info=true group=bin mode=0444 owner=root path=usr/share/info/mh-e-1 [...] file [...] chash=[...] facet.doc.info=true group=bin mode=0444 owner=root path=usr/share/info/mh-e-2 [...] [...] Yes, they're associated with facet.doc.info. Now let's look at the facet settings on my desktop: $ pkg facet FACETS VALUE facet.locale.en* True facet.locale* False facet.doc.man True facet.doc* False $ Oops. I've got man pages and various English documentation files, but not the Info files. Let's fix that: # pkg change-facet facet.doc.info=True Packages to update: 970 Variants/Facets to change: 1 Create boot environment: No Create backup boot environment: Yes Services to change: 1 DOWNLOAD PKGS FILES XFER (MB) Completed 970/970 181/181 9.2/9.2 PHASE ACTIONS Install Phase 226/226 PHASE ITEMS Image State Update Phase 2/2 PHASE ITEMS Reading Existing Index 8/8 Indexing Packages 970/970 # Now we have the info files: $ ls -F /usr/share/info a2ps.info dir@ flex.info groff-2 regex.info aalib.info dired-x flex.info-1 groff-3 remember ...

    Read the article

  • Secret Agent Man

    - by Bil Simser
    Just a quick one this morning as we all get started in the week. Something that comes into play (sometimes in a big way) is the user agent string your browser gives off. So for example using the User-Agent field in the request header, you can determine what browser the user is running and act accordingly.Internet Explorer 9 modified the UA string slightly so just in case you're looking for it here are the user agent strings for IE9 (in various modes):Internet Explorer 9 Mode: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0)Internet Explorer 8 Mode: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MS-RTC LM 8; InfoPath.3; .NET4.0C; .NET4.0E; Zune 4.7)Internet Explorer 7 Mode: Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MS-RTC LM 8; InfoPath.3; .NET4.0C; .NET4.0E; Zune 4.7)Internet Explorer 9 (Compatibility Mode): Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/5.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MS-RTC LM 8; InfoPath.3; .NET4.0C; .NET4.0E; Zune 4.7)A couple of things to note here:This was from a 64-bit Windows 7 client so that might account for the WOW64 in the agent string (I don't have a 32-bit client to test from)Various applications and platforms add to the UA string just like they do in previous IE releases. So for example you can see I have various .NET versions installed as well as Zune. You can take advantage of this by querying the UA string for compatibilities and present options accordingly to the end user.As applications will continue to add and modify this string you'll want to query the string for parts not the entire string. For example if you want to detect if you're coming from IE running  on a Windows Phone 7 just look for "iemobile" in the user agent stringHappy hacking!

    Read the article

  • Use Twitter in Windows Media Center with TwitterMCE

    - by DigitalGeekery
    Are you a Media Center user who just can’t get enough Twitter? If so, you may want to check out the TwitterMCE plugin for Windows Media Center. Download and install TwitterMCE application. (See download link below) When you start Windows Media Center, you’ll find the TwitterMCE icon listed in the Extras. When you open the plug-in you’ll be prompted for a Paypal donation and have to wait out the 15 second timer. Next, you’ll need to log in to your Twitter account. Enter your Twitter account username and password. You can do this with the keyboard or by entering letters and numbers with a Media Center remote. When you are finished, select the Login button.   You’ll be prompted to select Standard or Video Mode. Standard displays items in a more vertical fashion. Video displays them horizontally and one at a time, and also allows you to watch Live TV, a movie, or video at the same time. Reading Your Tweets Clicking on Home allows you to read the latest Twitter messages from your friends. You can access the previous 20 tweets. Scroll up and down to see additional messages in Standard mode, ro right and left in Video mode. Click on the individual Twitter messages to get more information, such as which friend sent the tweet. Create a Tweet To Create a Tweet directly from Media Center, select the Update button. Type out your message using your keyboard or your remote and the on-screen keyboard. When you are finished, select Update to send your Twitter message. A few moments later your new tweet will appear.   To send a tweet while you are watching TV or a video, log in to the TwitterMCE app, choose the Video mode, and select Update.   Enter your tweet with the remote or keyboard. Select Update to send the tweet.   You can also view Mentions, Friends, and Followers selecting the appropriate button.   Scroll through your list of friends to read their latest tweets.   The TwitterMCE plugin works will Windows Vista Premium, Ultimate, and Windows 7. It might not completely replace your favorite Twitter App, but it will allow you to send all the tweets you want without having to take your eyes off your favorite TV programs. Download TwitterMCE Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)Schedule Updates for Windows Media CenterIntegrate Hulu Desktop and Windows Media Center in Windows 7Add Color Coding to Windows 7 Media Center Program GuideIntegrate Boxee with Media Center in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Get Your Delicious Bookmarks In Firefox’s Awesome Bar Manage Photos Across Different Social Sites With Dropico Test Drive Windows 7 Online Download Wallpapers From National Geographic Site Spyware Blaster v4.3 Yes, it’s Patch Tuesday

    Read the article

  • Use your iPhone or iPod Touch as a Boxee Remote

    - by DigitalGeekery
    Are you a Boxee user looking for a remote control solution? Well, you might not need to look any further than your pocket. The free Boxee Remote App turns your iPhone or iPod Touch into a a simple and easy-to-use Boxee remote. The Boxee Remote App works over WiFi, so there is no need for to buy or install additional hardware on your PC. Plus, you don’t even need to be within the line of sight for it to work. Using the Boxee Remote App Download the free Boxee Remote App from the App Store and install it on your iPhone or iPod Touch. See download link below. Next, make sure you have Boxee running on your PC. Select the Boxee icon to open the App.   The first time you log in you’ll be greeted by an introduction screen that will explain the two modes. Click Continue. When opened in “Button” mode, you’ll be presented with 4 directional buttons, an “OK” button, and a back arrow button that works like the Esc key does in Boxee. Button mode performs just as a normal remote. Touching the directional buttons moves your on screen selection right, left, up, and down. Tap the OK button to open or select an item. To enter “Gesture” mode, tap the Gesture button along the top of the Screen. Gesture mode works similar to a touch pad or trackball on a laptop. You drag the Boxee icon with your thumb or finger across the screen to move around within Boxee. The icon will turn red while being dragged or touched. Simply tap the icon to select.   The Settings button allows you to manually add or delete a host computer, or adjust the sensitivity of the controls.     If you need to enter text, such as enter logon credentials for an App, the on screen keyboard will pop up. While watching a video you’ll have on-screen Stop and Pause buttons along with a volume slider.   The Boxee Remote App is simple and easy to use. As long as you can connect via WiFi, you can use it to control any instance of Boxee running on any computer on your network. Download the Boxee Remote App Similar Articles Productive Geek Tips Why Wait? Amazing New Add-on Turns Your iPhone into an iPad! [Comic]Getting Started with BoxeeIntegrate Boxee with Media Center in Windows 7Watch Netflix Instant Movies in BoxeeWin a Free iPod Touch in the How-To Geek Facebook Giveaway! TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows SyncToy syncs Files and Folders across Computers on a Network (or partitions on the same drive) If it were only this easy Classic Cinema Online offers 100’s of OnDemand Movies OutSync will Sync Photos of your Friends on Facebook and Outlook

    Read the article

  • Rotating text using CSS

    - by Renso
    Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Goal: Rotating text using css only. How: Surprisingly IE supports this feature rather well. You could use property filters in IE, but since this is only supported on IE browsers, I would not recommend it. CSS3, still in proposal state, has a "writing-mode" property for doing this. It has been part of IE's browser engine since IE5.5. Now that it is part of the CSS3 draft specification, would be the best way to implement this going forward. Webkit based browsers; Firefox 3.5+, Opera 11 and IE9 implement this feature differently by utilizing the transform property. Without using third-party JavaScript or CSS properties, we can use the CSS3 "writing-mode" property, supported from IE5.5 up to IE8, the latter adding addition formatting options through -ms extensions. <style type="text/css"> .rightToLeft{ writing-mode: tb-rl; } </style> <p class="rightToLeft">This is my text</p> This will rotate the text 90 degrees, starting from the right to the left. Here are all the options: ·         lr-tb – Default value, left to right, top to bottom ·         rl-tb – Right to left, top to bottom ·         tb-rl – Vertically; top to bottom, right to left ·         bt-rl – Vertically; bottom to top, right to left ·         tb-lr – Available in IE8+: -ms-writing-mode; top to bottom, left to right ·         bt-lr – Bottom to top, left to right ·         lr-bt – Left to right, bottom to top What about Firefox, Safari, etc.? The following techniques need to be used on Webkit browsers like Firefox, Opera 11, Google Chrome and IE9. These browsers require their proprietary vendor extensions: -moz-, -webkit-, -o- and -ms-. -webkit-transform: rotate(90deg);    -moz-transform: rotate(90deg); -ms-transform: rotate(90deg); -o-transform: rotate(90deg); transform: rotate(90deg);

    Read the article

  • Rotating WebLogic Server logs to avoid large files using WLST.

    - by adejuanc
    By default, when WebLogic Server instances are started in development mode, the server automatically renames (rotates) its local server log file as SERVER_NAME.log.n.  For the remainder of the server session, log messages accumulate in SERVER_NAME.log until the file grows to a size of 500 kilobytes.Each time the server log file reaches this size, the server renames the log file and creates a new SERVER_NAME.log to store new messages. By default, the rotated log files are numbered in order of creation filenamennnnn, where filename is the name configured for the log file. You can configure a server instance to include a time and date stamp in the file name of rotated log files; for example, server-name-%yyyy%-%mm%-%dd%-%hh%-%mm%.log.By default, when server instances are started in production mode, the server rotates its server log file whenever the file grows to 5000 kilobytes in size. It does not rotate the local server log file when the server is started. For more information about changing the mode in which a server starts, see Change to production mode in the Administration Console Online Help.You can change these default settings for log file rotation. For example, you can change the file size at which the server rotates the log file or you can configure a server to rotate log files based on a time interval. You can also specify the maximum number of rotated files that can accumulate. After the number of log files reaches this number, subsequent file rotations delete the oldest log file and create a new log file with the latest suffix.  Note: WebLogic Server sets a threshold size limit of 500 MB before it forces a hard rotation to prevent excessive log file growth. To Rotate via WLST : #invoke WLSTC:\>java weblogic.WLST#connect WLST to an Administration Serverawls:/offline> connect('username','password')#navigate to the ServerRuntime MBean hierarchywls:/mydomain/serverConfig> serverRuntime()wls:/mydomain/serverRuntime>ls()#navigate to the server LogRuntimeMBeanwls:/mydomain/serverRuntime> cd('LogRuntime/myserver')wls:/mydomain/serverRuntime/LogRuntime/myserver> ls()-r-- Name myserver-r-- Type LogRuntime-r-x forceLogRotation java.lang.Void :#force the immediate rotation of the server log filewls:/mydomain/serverRuntime/LogRuntime/myserver> cmo.forceLogRotation()wls:/mydomain/serverRuntime/LogRuntime/myserver> The server immediately rotates the file and prints the following message: <Mar 2, 2012 3:23:01 PM EST> <Info> <Log Management> <BEA-170017> <The log file C:\diablodomain\servers\myserver\logs\myserver.log will be rotated. Reopen the log file if tailing has stopped. This can happen on some platforms like Windows.><Mar 2, 2012 3:23:01 PM EST> <Info> <Log Management> <BEA-170018> <The log file has been rotated to C:\diablodomain\servers\myserver\logs\myserver.log00001. Log messages will continue to be logged in C:\diablodomain\servers\myserver\logs\myserver.log.> To specify the Location of the archived Log Files The following command specifies the directory location for the archived log files using the -Dweblogic.log.LogFileRotationDir Java startup option: java -Dweblogic.log.LogFileRotationDir=c:\foo-Dweblogic.management.username=installadministrator-Dweblogic.management.password=installadministrator weblogic.Server For more information read the following documentation ; Using the WebLogic Scripting Tool http://download.oracle.com/docs/cd/E13222_01/wls/docs103/config_scripting/using_WLST.html Configuring WebLogic Logging Services http://download.oracle.com/docs/cd/E12840_01/wls/docs103/logging/config_logs.html

    Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >