Search Results

Search found 18749 results on 750 pages for 'komodo edit'.

Page 114/750 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

  • No Outbound Internet on Windows Home Server

    - by Kyle B.
    Could someone provide some steps for me to check my internet connection on my Windows Home Server? It seems to have intermittent connectivity issues and I am unsure of how to diagnose the problem because it is a headless (no monitor, no keyboard) machine so the only way to get to the device is via remote desktop (which works fine). When connected to the machine, it doesn't pull up any microsoft.com sites and some other sites it does pull up (i.e. gmail.com) and some it doesn't (stackoverflow.com). To make matters more complicated, it has worked intermittently in the past for reasons unknown. Are there tools I can use to properly diagnose the reason for the connection failure? I can ping 127.0.0.1 just fine, I have internet working on my other router-connected machines, so I'm not sure why this one would fail. Any suggestions would be much appreciated and up-voted :) ** edit - thanks for suggestions guys, I'm going to try these tonight and will update my post. ** edit #2 - I hoping this is a more permanant fix, but I have both changed my port on the router as well as restarted the router at the same time. The internet (for the moment) appears to be working. I will be sure to try everything we have discussed should this problem persist. Thanks, Kyle

    Read the article

  • Windows Server 2003 DHCP not handing out IPs

    - by SnOrfus
    I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

    Read the article

  • VLAN with trunk to avoid broadcast storm in a network with redundant paths

    - by liv2hak
    I have 6 Juniper switches (EX - 2200) connected to each other as shown in the network topology. I have two PC's that I am using PC1 - (used for configuring the 6 switches via minicom) PC2 - to monitor the traffic between the switches via the Ports that are marked with arrows in the diagram. STEP 1: I create a new vlan On Switch 3 (SW3) that includes Port 12 and Port 22. I also assign l3-interface to the vlan (vlan_2) with ip address - 192.168.1.7. Now I plug-in Port 0 of Switch 3 on PC2. Now I try pinging 192.168.1.7 from PC2 (192.168.1.10) I want to know what will happen? My postulation is that I will not be able to ping SW3 from PC2.This is because SW3 (Port 12 and Port 22) is a part of a vlan_2 and vlan_2 logically breaks up broadcast domains and so 192.168.1.7 will not be reachable from 192.168.1.10. Now I have an l3-interface on SW1 with IP 192.168.1.1 using default vlan( vlan-id 0). Similarly I have enabled IP on SW2 - 192.168.1.2 SW3 - 192.168.1.3 SW4 - 192.168.1.4 SW5 - 192.168.1.5 SW6 - 192.168.1.6 all using default vlan. I create VLAN2 with the following configuration SW3 - Port 12,Port 22. SW6 - Port 14 I create VLAN3 with the following configuration SW3 - Port 0 SW6 - Port 0 I also configure a VLAN trunk between SW3 and SW6 using the following commands. edit interfaces ge-0/0/12 set unit 0 family ethernet-switching port-mode trunk edit interfaces ge-0/0/12 set unit 0 family ethernet-switching vlan members all There is a redundant path in the network as the loop between SW3 and SW6 is closed.There is no broadcast storm in the network? What is the reason for this? I have not enabled STP or RSTP.still there is no broadcast storm.what is the reason for this. (Please ignore the CISCO symbol on the switches in the diagram.All swithes are Junper EX 22-00.)

    Read the article

  • org-sort multi: date/time (?d ?t) | priority (?p) | title (?a)

    - by lawlist
    Is anyone aware of an org-sort function / modification that can refile / organize a group of TODO so that it sorts them by three (3) criteria: first sort by due date, second sort by priority, and third sort by by title of the task? EDIT: I believe that org-sort by deadline (?d) has a bug that cannot properly handle undated tasks. I am working on a workaround (i.e., moving the undated todo to a different heading before the deadline (?d) sort occurs), but perhaps the best thing to do would be to try and fix the original sorting function. Development of the workaround can be found in this thread (i.e., moving the undated tasks to a different heading in one fell swoop): How to automate org-refile for multiple todo EDIT: Apparently, the following code (ancient history) that I found on the internet was eventually modified and included as a part of org-sort-entries. Unfortunately, undated todo are not properly sorted when sorting by deadline -- i.e., they are mixed in with the dated todo. ;; multiple sort (defun org-sort-multi (&rest sort-types) "Multiple sorts on a certain level of an outline tree, or plain list items. SORT-TYPES is a list where each entry is either a character or a cons pair (BOOL . CHAR), where BOOL is whether or not to sort case-sensitively, and CHAR is one of the characters defined in `org-sort-entries-or-items'. Entries are applied in back to front order. Example: To sort first by TODO status, then by priority, then by date, then alphabetically (case-sensitive) use the following call: (org-sort-multi '(?d ?p ?t (t . ?a)))" (interactive) (dolist (x (nreverse sort-types)) (when (char-valid-p x) (setq x (cons nil x))) (condition-case nil (org-sort-entries (car x) (cdr x)) (error nil)))) ;; sort current level (defun lawlist-sort (&rest sort-types) "Sort the current org level. SORT-TYPES is a list where each entry is either a character or a cons pair (BOOL . CHAR), where BOOL is whether or not to sort case-sensitively, and CHAR is one of the characters defined in `org-sort-entries-or-items'. Entries are applied in back to front order. Defaults to \"?o ?p\" which is sorted by TODO status, then by priority" (interactive) (when (equal mode-name "Org") (let ((sort-types (or sort-types (if (or (org-entry-get nil "TODO") (org-entry-get nil "PRIORITY")) '(?d ?t ?p) ;; date, time, priority '((nil . ?a)))))) (save-excursion (outline-up-heading 1) (let ((start (point)) end) (while (and (not (bobp)) (not (eobp)) (<= (point) start)) (condition-case nil (outline-forward-same-level 1) (error (outline-up-heading 1)))) (unless (> (point) start) (goto-char (point-max))) (setq end (point)) (goto-char start) (apply 'org-sort-multi sort-types) (goto-char end) (when (eobp) (forward-line -1)) (when (looking-at "^\\s-*$") ;; (delete-line) ) (goto-char start) ;; (dotimes (x ) (org-cycle)) ))))) EDIT: Here is a more modern version of multi-sort, which is likely based upon further development of the above-code: (defun org-sort-all () (interactive) (save-excursion (goto-char (point-min)) (while (re-search-forward "^\* " nil t) (goto-char (match-beginning 0)) (condition-case err (progn (org-sort-entries t ?a) (org-sort-entries t ?p) (org-sort-entries t ?o) (forward-line)) (error nil))) (goto-char (point-min)) (while (re-search-forward "\* PROJECT " nil t) (goto-char (line-beginning-position)) (ignore-errors (org-sort-entries t ?a) (org-sort-entries t ?p) (org-sort-entries t ?o)) (forward-line)))) EDIT: The best option will be to fix sorting of deadlines (?d) so that undated todo are moved to the bottom of the outline, instead of mixed in with the dated todo. Here is an excerpt from the current org.el included within Emacs Trunk (as of July 1, 2013): (defun org-sort (with-case) "Call `org-sort-entries', `org-table-sort-lines' or `org-sort-list'. Optional argument WITH-CASE means sort case-sensitively." (interactive "P") (cond ((org-at-table-p) (org-call-with-arg 'org-table-sort-lines with-case)) ((org-at-item-p) (org-call-with-arg 'org-sort-list with-case)) (t (org-call-with-arg 'org-sort-entries with-case)))) (defun org-sort-remove-invisible (s) (remove-text-properties 0 (length s) org-rm-props s) (while (string-match org-bracket-link-regexp s) (setq s (replace-match (if (match-end 2) (match-string 3 s) (match-string 1 s)) t t s))) s) (defvar org-priority-regexp) ; defined later in the file (defvar org-after-sorting-entries-or-items-hook nil "Hook that is run after a bunch of entries or items have been sorted. When children are sorted, the cursor is in the parent line when this hook gets called. When a region or a plain list is sorted, the cursor will be in the first entry of the sorted region/list.") (defun org-sort-entries (&optional with-case sorting-type getkey-func compare-func property) "Sort entries on a certain level of an outline tree. If there is an active region, the entries in the region are sorted. Else, if the cursor is before the first entry, sort the top-level items. Else, the children of the entry at point are sorted. Sorting can be alphabetically, numerically, by date/time as given by a time stamp, by a property or by priority. The command prompts for the sorting type unless it has been given to the function through the SORTING-TYPE argument, which needs to be a character, \(?n ?N ?a ?A ?t ?T ?s ?S ?d ?D ?p ?P ?o ?O ?r ?R ?f ?F). Here is the precise meaning of each character: n Numerically, by converting the beginning of the entry/item to a number. a Alphabetically, ignoring the TODO keyword and the priority, if any. o By order of TODO keywords. t By date/time, either the first active time stamp in the entry, or, if none exist, by the first inactive one. s By the scheduled date/time. d By deadline date/time. c By creation time, which is assumed to be the first inactive time stamp at the beginning of a line. p By priority according to the cookie. r By the value of a property. Capital letters will reverse the sort order. If the SORTING-TYPE is ?f or ?F, then GETKEY-FUNC specifies a function to be called with point at the beginning of the record. It must return either a string or a number that should serve as the sorting key for that record. Comparing entries ignores case by default. However, with an optional argument WITH-CASE, the sorting considers case as well." (interactive "P") (let ((case-func (if with-case 'identity 'downcase)) (cmstr ;; The clock marker is lost when using `sort-subr', let's ;; store the clocking string. (when (equal (marker-buffer org-clock-marker) (current-buffer)) (save-excursion (goto-char org-clock-marker) (looking-back "^.*") (match-string-no-properties 0)))) start beg end stars re re2 txt what tmp) ;; Find beginning and end of region to sort (cond ((org-region-active-p) ;; we will sort the region (setq end (region-end) what "region") (goto-char (region-beginning)) (if (not (org-at-heading-p)) (outline-next-heading)) (setq start (point))) ((or (org-at-heading-p) (condition-case nil (progn (org-back-to-heading) t) (error nil))) ;; we will sort the children of the current headline (org-back-to-heading) (setq start (point) end (progn (org-end-of-subtree t t) (or (bolp) (insert "\n")) (org-back-over-empty-lines) (point)) what "children") (goto-char start) (show-subtree) (outline-next-heading)) (t ;; we will sort the top-level entries in this file (goto-char (point-min)) (or (org-at-heading-p) (outline-next-heading)) (setq start (point)) (goto-char (point-max)) (beginning-of-line 1) (when (looking-at ".*?\\S-") ;; File ends in a non-white line (end-of-line 1) (insert "\n")) (setq end (point-max)) (setq what "top-level") (goto-char start) (show-all))) (setq beg (point)) (if (>= beg end) (error "Nothing to sort")) (looking-at "\\(\\*+\\)") (setq stars (match-string 1) re (concat "^" (regexp-quote stars) " +") re2 (concat "^" (regexp-quote (substring stars 0 -1)) "[ \t\n]") txt (buffer-substring beg end)) (if (not (equal (substring txt -1) "\n")) (setq txt (concat txt "\n"))) (if (and (not (equal stars "*")) (string-match re2 txt)) (error "Region to sort contains a level above the first entry")) (unless sorting-type (message "Sort %s: [a]lpha [n]umeric [p]riority p[r]operty todo[o]rder [f]unc [t]ime [s]cheduled [d]eadline [c]reated A/N/P/R/O/F/T/S/D/C means reversed:" what) (setq sorting-type (read-char-exclusive)) (and (= (downcase sorting-type) ?f) (setq getkey-func (org-icompleting-read "Sort using function: " obarray 'fboundp t nil nil)) (setq getkey-func (intern getkey-func))) (and (= (downcase sorting-type) ?r) (setq property (org-icompleting-read "Property: " (mapcar 'list (org-buffer-property-keys t)) nil t)))) (message "Sorting entries...") (save-restriction (narrow-to-region start end) (let ((dcst (downcase sorting-type)) (case-fold-search nil) (now (current-time))) (sort-subr (/= dcst sorting-type) ;; This function moves to the beginning character of the "record" to ;; be sorted. (lambda nil (if (re-search-forward re nil t) (goto-char (match-beginning 0)) (goto-char (point-max)))) ;; This function moves to the last character of the "record" being ;; sorted. (lambda nil (save-match-data (condition-case nil (outline-forward-same-level 1) (error (goto-char (point-max)))))) ;; This function returns the value that gets sorted against. (lambda nil (cond ((= dcst ?n) (if (looking-at org-complex-heading-regexp) (string-to-number (match-string 4)) nil)) ((= dcst ?a) (if (looking-at org-complex-heading-regexp) (funcall case-func (match-string 4)) nil)) ((= dcst ?t) (let ((end (save-excursion (outline-next-heading) (point)))) (if (or (re-search-forward org-ts-regexp end t) (re-search-forward org-ts-regexp-both end t)) (org-time-string-to-seconds (match-string 0)) (org-float-time now)))) ((= dcst ?c) (let ((end (save-excursion (outline-next-heading) (point)))) (if (re-search-forward (concat "^[ \t]*\\[" org-ts-regexp1 "\\]") end t) (org-time-string-to-seconds (match-string 0)) (org-float-time now)))) ((= dcst ?s) (let ((end (save-excursion (outline-next-heading) (point)))) (if (re-search-forward org-scheduled-time-regexp end t) (org-time-string-to-seconds (match-string 1)) (org-float-time now)))) ((= dcst ?d) (let ((end (save-excursion (outline-next-heading) (point)))) (if (re-search-forward org-deadline-time-regexp end t) (org-time-string-to-seconds (match-string 1)) (org-float-time now)))) ((= dcst ?p) (if (re-search-forward org-priority-regexp (point-at-eol) t) (string-to-char (match-string 2)) org-default-priority)) ((= dcst ?r) (or (org-entry-get nil property) "")) ((= dcst ?o) (if (looking-at org-complex-heading-regexp) (- 9999 (length (member (match-string 2) org-todo-keywords-1))))) ((= dcst ?f) (if getkey-func (progn (setq tmp (funcall getkey-func)) (if (stringp tmp) (setq tmp (funcall case-func tmp))) tmp) (error "Invalid key function `%s'" getkey-func))) (t (error "Invalid sorting type `%c'" sorting-type)))) nil (cond ((= dcst ?a) 'string<) ((= dcst ?f) compare-func) ((member dcst '(?p ?t ?s ?d ?c)) '<))))) (run-hooks 'org-after-sorting-entries-or-items-hook) ;; Reset the clock marker if needed (when cmstr (save-excursion (goto-char start) (search-forward cmstr nil t) (move-marker org-clock-marker (point)))) (message "Sorting entries...done"))) (defun org-do-sort (table what &optional with-case sorting-type) "Sort TABLE of WHAT according to SORTING-TYPE. The user will be prompted for the SORTING-TYPE if the call to this function does not specify it. WHAT is only for the prompt, to indicate what is being sorted. The sorting key will be extracted from the car of the elements of the table. If WITH-CASE is non-nil, the sorting will be case-sensitive." (unless sorting-type (message "Sort %s: [a]lphabetic, [n]umeric, [t]ime. A/N/T means reversed:" what) (setq sorting-type (read-char-exclusive))) (let ((dcst (downcase sorting-type)) extractfun comparefun) ;; Define the appropriate functions (cond ((= dcst ?n) (setq extractfun 'string-to-number comparefun (if (= dcst sorting-type) '< '>))) ((= dcst ?a) (setq extractfun (if with-case (lambda(x) (org-sort-remove-invisible x)) (lambda(x) (downcase (org-sort-remove-invisible x)))) comparefun (if (= dcst sorting-type) 'string< (lambda (a b) (and (not (string< a b)) (not (string= a b))))))) ((= dcst ?t) (setq extractfun (lambda (x) (if (or (string-match org-ts-regexp x) (string-match org-ts-regexp-both x)) (org-float-time (org-time-string-to-time (match-string 0 x))) 0)) comparefun (if (= dcst sorting-type) '< '>))) (t (error "Invalid sorting type `%c'" sorting-type))) (sort (mapcar (lambda (x) (cons (funcall extractfun (car x)) (cdr x))) table) (lambda (a b) (funcall comparefun (car a) (car b))))))

    Read the article

  • How to create an MST for silent install using Orca?

    - by Sanarothe
    Hi. I'm trying to deploy 7zip via GPO; I assigned the original MSI, but the package installation simply doesn't take place. What I've gathered is that I need to create an MST. In the spirit of trying to learn as much as possible about it, I've opted to use Orca rather than a third-party automagic tool, but I'm at a loss as to which fields to edit. So far the only change that I've made is to give the license accepted checkbox a value of "1" instead of pointing to another key that, still, just gave it a value of "1." So, to give this some structure, How does (Or what criteria should I consider) creating a MST make the install noninteractive/silent? Do you have to manually reconfigure the MSI to simply not perform the GUI aspects? Or do I have to execute the program in silent mode after defining the variables the the installer requests? (Though, of course, it seems that would defeat the purpose of the MST) How do I determine which fields I need to edit? I've loaded the installer and it takes three inputs: License acceptance, feature set and installation location. I want all of the default values: I'm just trying to deploy it at all, not customize the installation. I BELIEVE that I should be messing with some values in the Registry table, but I really don't know. If I'm not asking the right questions, can someone point me to a THOROUGH resource or documentation for this process? I've already gone over the technet articles on basic Orca use and deployment, but I couldn't really find anything on creating MST that didn't involve a third party program in which one runs a 'dummy' installer to get the before and after snapshots. Thank you very much, Cameron UPDATE: After spending the day troubleshooting, I finally got my server to send out 7zip, but not until I had also assigned firefox. Not sure why it didn't want to send out 7zip by itself, but I also had some domain naming problems. Thanks for the input (GPResult helped enormously.)

    Read the article

  • Windows file locks allowing multiple users to write to open file over network

    - by JPbuntu
    I have 6 windows computers (xp,vista,7) that need to access a samba share (Ubuntu 12.04). I am trying to make it so only one client can open a file at a given time. I thought this was pretty standard behavior of file locks, but I can't get it to work. The way it is right now a file can be open by two users, and changed and saved by either one of them. The last file saved overwrites what ever changes the other user made. At first I thought this was a Samba configuration problem, but I get this behavior even between two windows machines. So far I have only tested: Windows Xp Windows Vista Windows XP Samba << Windows Vista and both give the same behavior. When I tested the Samba configuration, I had set strict locking = yes and get errors logged like this: close_remove_share_mode: Could not get share mode lock for file _prod/part_number_list_COPY.xlsx Eventually all of the files are going to be moved onto the Samba share, so that is the configuration I am most concerned about fixing. Any ideas? Thanks in advance. EDIT: I tested an excel file again, and it is now working properly in both above mentioned cases, I am also no longer getting the above mentioned error. I don't know what happened, perhaps a restart fixed it? (also works with strict locking = no) Although I still need to find a solution for the CAD/CAM files we use, the software is Vector and it does not seem to be using file locks. Is there any software that I can use to manage these files, so two people can't open/edit them at a time? Maybe a windows application that forces file locks? Or a dirt simple version control system? (the only ones I have seen at are too complicated for our needs).

    Read the article

  • DNS configuration issues. Clients inside network unable to resolve DNS server's name

    - by hydroparadise
    Setup the DNS service on Ubuntu 12.04 64 and all apears to be well except that my dhcp clients do not recognize my DNS servers hostname. When doing a nslookup on one of my Windows clients, I get C:\Users\chad>nslookup Default Server: UnKnown Address: 192.168.1.2 Where I would expect the FQDN in the spot where UnKnown is seen. The DNS server know's itself pretty well, but I think only because I have an entry in the /etc/hosts file to resolve. There's so many places to look I don't even know where to begin. Are there any logs I can look at? Something. Places I've looked at and configured: /etc/bind/zones/domain.com.db /etc/bind/zones/rev.1.168.192.in-addr.arpa /etc/bind/named.conf.local EDIT: '/etc/bind/zones/rev.1.168.192.in-addr.arpa' @ IN SOA dns-serv1.mydomain.com [email protected]. ( 2006081401; 28800; 604800; 604800; 86400 ) IN NS dns-serv1.mydomain.com. 2 IN PTR dns-serv1 2 IN PTR mydomain.com EDIT 2: '/etc/bind/named.conf.local' zone "mydomain.com" { type master; file "/etc/bind/zones/mydomain.com.db"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.0.168.192.in-addr.arpa"; };

    Read the article

  • How do I use a self encrypting drive?

    - by Unique_Key
    I recently purchased a Micron RealSSD c400 self encrypting drive, and I am having a few issues when trying to get it recognized by my laptop (HP Elitebook 8440p running Windows 7 x64; also tried on a custom-built desktop). When I try to initialize the drive from disk management, I get a CRC error; also, when attempting to partition it from Windows setup, the program can't create the partitions. I also tried with UBCD, nothing. I assume this is due to drive security, but I haven't been able to find much information about this online; do I need a management software or something? I'm completely stumped here. EDIT As requested, when I try partitioning the device from Windows setup I get a 0x80300024 error; when I try initializing it from disk management, I get a "Data error (cyclic redundancy check)" message, and the event log shows the following under System: Source: VDS Basic Provider, message: unexpected failure. error code 490@01010004 (2x) Source: Virtual Disk Service, message: VDS fails to write boot code on a disk during clean operation. Error code: 80070001@02070008 (1x) Source: Disk, message: The device \Device\Harddisk2\DR2 has a bad block (2x) The security logs show nothing related. Also, when attempting to configure it from UBCD (utility: HDAT2), I get an error along the lines of "can't edit partition information" or something to that tune.

    Read the article

  • Restoring open software after a restart event in windows

    - by Doltknuckle
    I find that at the end of a long day, I sometimes have a large number of programs running. All which I will need to use tomorrow. Normally, this isn't an issue, I can simply lock the machine and come back tomorrow. My problem arrises when windows update launches in the middle of the night and force restarts my computer. That in turns closes all my open software. I of course save everything regularly so I don't loose anything, but I waste time reopening all of those resources whenever there is a restart. [EDIT] I should clarify that I still want to be able to restart my computer when an update comes down. Preventing the restart only delays the problem until later. I should have been more specific in that I want to be able to recover my working environment after a restart for any reason. Things like scheduled maintence, power loss, updates, and software installs. [EDIT] I can't simply have them setup to launch at startup becasuse those files change from week to week. So I need something that monitors what I have open, and gives me the option to "recover" those software sessions when I log back in. Anyone have any suggestions on what I can do? I'd even be willing to purchase software to do this for me if that is the only option. Thanks

    Read the article

  • Fedora, ssh and sudo

    - by Ricky Robinson
    I have to run a script remotely on several Fedora machines through ssh. Since the script requires root priviliges, I do: $ ssh me@remost_host "sudo touch test_sudo" #just a simple example sudo: no tty present and no askpass program specified The remote machines are configured in such a way that the password for sudo is never asked for. For the above error, the most common fix is to allocate a pseudo-terminal with the -t option in ssh: $ ssh -t me@remost_host "sudo touch test_sudo" sudo: no tty present and no askpass program specified Let's try to force this allocation with -t -t: $ ssh -t -t me@remost_host "sudo touch test_sudo" sudo: no tty present and no askpass program specified Nope, it doesn't work. In /etc/sudoers of course I have this line: #Defaults requiretty ... but I can't manually change it on tens of remote machines. Am I missing something here? Is there an easy fix? EDIT: Here is the sudoers file of a host where ssh me@host "sudo stat ." works. Here is the sudoers file of a host where it doesn't work. EDIT 2: Running tty on a host where it works: $ ssh me@host_ok tty not a tty $ ssh -t me@host_ok tty /dev/pts/12 Connection to host_ok closed. $ ssh -t -t me@host_ok tty /dev/pts/12 Connection to host_ok closed. Now on a host where it doesn't work: $ ssh me@host_ko tty not a tty $ ssh -t me@host_ko tty not a tty Connection to host_ko closed. $ ssh -t -t me@host_ko tty not a tty Connection to host_ko closed.

    Read the article

  • How to wire 20 computers and 20 phones and 1 server into LAN?

    - by John Smith
    I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

    Read the article

  • backupexec 12.5 not following symlinks on linux agent

    - by Peter Carrero
    Ok, we are at a loss here trying to backup a linux box to a backupexec server... we got a backupexec 12.5 server and a "backupexec for windows servers linux agent" (sigh) running on one of our linux boxes. When a backup runs, we get exceptions reported for our symbolic links. it says something like: BACKUP- \\<servername>\[ROOT] File \\<servername>\[ROOT]/<foldername>/<symlink> is in the backup selection list but was not found. Looking at the selection list, the symlink shows as a 1k file on BUE. Tools-Options-Backup has Backup files and directories by following symbolic links/junction points selected. These same checkboxes are selected on the Job Setup-Job Properties-Edit Template-Advanced Additionally, all the checkboxes are checkeced on Tools-Options-Linux, Unix, and Macintosh and on the Job Set-Job Properties-Edit Template-Linux, Unix, and Macintosh. These checkboxes read: "Preserve change time", "Follow local mount points", "Follow remote mount points", "Backup contents of soft-linked directories" and "Lock remote files", but apparently changing those options produce the same result. Any help on how to get BUE to make a proper backup would be greatly appreciated. Thanks.

    Read the article

  • Windows Server 2003 DHCP not handing out IPs

    - by SnOrfus
    I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

    Read the article

  • mysql mass insert data

    - by user12145
    Edit: I realized that if I construct a large query in memory, the speed has increased almost 10 times of magnitude "insert ignore into xxx(col1, col2) values('a',1), values('b',1), values('c',1)..." Edit: since I have an index on the first column, the insert time creeps up as I insert more. Can I delay the index until the end? Original: I'm using the following to batch insert 10 million rows into mysql db(not all at once, since they don't all fit into memory), it's too slow(taking many hours). should I use load file to improve performance? I would have to create a second file to store all the 10 million rows, then load that into db. are there better ways? PreparedStatement st=con.prepareStatement("insert ignore into xxx (col1, col2) "+ " values (?, 1)"); Iterator d=data.iterator(); while(d.hasNext()){ st.clearParameters(); st.setString(1, (d.next()).toLowerCase()); st.addBatch(); } int[]updateCounts=st.executeBatch();

    Read the article

  • AMD FX8350 CPU - CoolerMaster Silencio 650 Case - New Water Cooling System

    - by fat_mike
    Lately after a use of 6 months of my AMD FX8350 CPU I'm experiencing high temperatures and loud noise coming from the CPU fan(I set that in order to keep it cooler). I decided to replace the stock fan with a water cooling system in order to keep my CPU quite and cool and add one or two more case fans too. Here is my case's airflow diagram: http://www.coolermaster.com/microsite/silencio_650/Airflow.html My configuration now is: 2x120mm intake front(stock with case) 1x120mm exhaust rear(stock with case) 1 CPU stock I'm planning to buy Corsair Hydro Series H100i(www.corsair.com/en-us/hydro-series-h100i-extreme-performance-liquid-cpu-cooler) and place the radiator in the front of my case(intake) and add an 120mm bottom intake and/or an 140mm top exhaust fan. My CPU lies near the top of the MO. Is it a good practice to have a water-cooling system that takes air in? As you can see here the front of the case is made of aluminum. Can the fresh air go in? Does it even fit? If not, is it wiser to get Corsair Hydro Series H80i (www.corsair.com/en-us/hydro-series-h80i-high-performance-liquid-cpu-cooler) and place the radiator on top of my case(exhaust) and keep the front 2x120mm stock and add one more as intake on bottom. If you have any other idea let me know. Thank you. EDIT: The CPU fan running ~3000rpm and temp is around 40~43C on idle and save energy. When temp is going over 55C when running multiple programs and servers on localhost(tomcat, wamp) rpm is around 5500 and loud! I'm running Win8.1 CPU not overclocked PS: Due to my reputation i couldn't post the links that was necessary. I will edit ASAP.

    Read the article

  • Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

    - by leladax
    EDIT: (Was: Laptop automatic shutdown after 2 seconds) If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?] Previous question (before EDIT. Sorry, but someone thought it productive to lock the other one as duplicate): I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

    Read the article

  • How to create VirtualHost in Ubuntu 12.10

    - by Mifas
    I had followed many articles to 'How to create VirtualHost in Ubuntu'. This is what have I done Installed Apache sudo apt-get install lamp-server^ phpmyadmin I created folder called site1.com in /var/www/ Then I have created the file in /etc/apache2/sites-available/site1.com Then added the following code to that site1.com file <VirtualHost *:80> ServerName www.site1.com ServerAdmin [email protected] ServerAlias site1.com DocumentRoot /var/www/site1.com # Other directives here <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site1.com/> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny Allow from all </Directory> </VirtualHost> Then after that I edit the host file added the following line of code 127.0.0.1 site1.com Edit Also I enable the site1.com via sudo a2ensite site1.com Then i restart the apache serivice. (Even i restarted the pc) When I go to the site1.com, It will say The connection has timed out Error Message. But I can browse via localhost/site1.com. I have been trying since last two days. No solution. And followed many articles and videos.

    Read the article

  • Querying a CSV file

    - by sheepsimulator
    Does anyone know of a simple tool that will open up a CSV file and let you do basic, SQLesque queries on it? Like a graphical tool of sorts, one that is easy to use. I know I could write a small script to do an import of the CSV into a SQLite database, but since I imagine someone else thought of this before me, I just wanted to inquire if one existed. What's prompting this question is I am getting frustrated with Excel's limited filtering capabilities. Perhaps some other data visualization manipulation tool would provide similar functionality. Free or OSS is preferred, but I'm open to any suggestions. EDIT: I really would prefer some clear tutorials on how to do the below instead of just "make your sheet an ODBC entry" or "write programs using ODBC files", or more ideas on apps to use. Note: I cannot use MS Access. Yet another EDIT: I'm still open for solutions using SQLite. My platform is a semi-ancient Win2k laptop, with a P4 on it. It's quite slow, so a resource-light solution is ideal and would likely get the win.

    Read the article

  • 24TB RAID 6 configuration

    - by Phil
    I am in charge of a new website in a niche industry that stores lots of data (10+ TB per client, growing to 2 or 3 clients soon). We are considering ordering about $5000 worth of 3TB drives (10 in a RAID 6 configuration and 10 for backup), which will give us approximately 24 TB of production storage. The data will be written once and remain unmodified for the lifetime of the website, so we only need to do a backup one time. I understand basic RAID theory, however I am not experienced with it. My question is, does this sound like a good configuration? What potential problems could this setup cause? Also, what is the best way to do a one-time backup? Have two RAID 6 arrays, one for offsite backup and one for production? Or should I backup the RAID 6 production array to a JBOD? EDIT: The data server is running Windows 2008 Server x64. EDIT 2: To reduce rebuild time, what would you think about using two RAID 5's instead of one RAID 6?

    Read the article

  • How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

    - by McCoy
    Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

    Read the article

  • Dropbox failing to update?

    - by Mick
    I have two PC's at home. One XP the other Windows 7-64bit. I have a word document that I edit on either PC - to enable this I have the file stored in a Dropbox folder. This usually works fine - but sometimes I find that the file does not get updated on my windows7 PC. I.e. I edit the file on my Windows XP machine, then go to my Windows 7 PC and see that there is a previous, old, datestamp on the file and sure enough if I open up the file to have a look, I see that the latest edits are not included. If I right-click on the file and select "Browse on Dropbox website" I see that the latest file is correctly there. Surely there must be some option to say please update this file - but can find no such thing. Has something gone wrong? I should point out that my wireless internet connection is a little intermittent - could this have caused some glitch? By the way I do not leave the old file open in word on my Windows-7 PC as I can well imagine that would cause trouble. Also I should mention that the icon on the document has the little green tick on it showing that Dropbox is not in the process of doing a transfer. Also the Dropbox icon in my system tray also has the green tick - so Dropbox is not busy transferring some other file(s). If I hover the mouse over the Dropbox icon I get the tooltip "All files up to date".

    Read the article

  • how to remove an entry from system tray?

    - by altvali
    I've searched for an answer to this one and I haven't found one yet. How do i remove a single item from Windows' System tray? I'm targeting Windows XP. Edit: This is not about preventing items from starting up. I want the program to keep running, I just need another script/program to remove the first one's entry from system tray. Second Edit: One approach that I can think of is to try to hide the intended app by modifying registry keys. On several test machines I've found some registry entries that match the System tray information at HKEY_USERS\something-that-looks-like S-1-5-21-682003330-1563985344-725345543-1003\Software\Microsoft\Windows\CurrentVersion\Explorer\TrayNotify with BalloonTip, IconStream and PastIconsStream containing systray information. The important one is IconStream. On other machines, these are found at hkey_classes_root/local/setting/software/microsoft/windows/currentversion/TrayNotify I'm quite sure there's no danger in changing those specific registries, but I don't know how to write code for that. Can anyone help me with the code and with confirming if this has the desired effect of hiding the systray icon for an active program?

    Read the article

  • Apache2 process stuck at 100% cpu, CLOSE_WAIT socket lingering

    - by mmazing
    I've troubleshooted the heck out of this today, and I can't seem to find any information on how to determine what is happening exactly. Basically, on my development server, another developer is causing CLOSE_WAIT connections that eat up one or more apache2 processes for several hours if I don't restart apache2. strace on any of the processes yields no information, only that it was able to attach. mod_proxy is not enabled. KeepAlive is on, KeepAliveTimeout is 15 seconds, MaxKeepAliveRequests is 100. From what I've been reading, this may or may not be an apache issue at all, just that that's how CLOSE_WAIT works (the server is waiting for a FIN packet to close the connection). I just can't believe that a server would be crippled so easily by not receiving a packet from a remote host telling it to close the connection. Especially without any intervention for well over an hour. Any tips? I'm about to pull my hair out. Edit : Also, there are no unusual entries in any apache log files. Edit 2: lsof -i shows only a single CLOSE_WAIT per hanging process. (That's what has been bothering me about this, as most other discussions talk about many CLOSE_WAIT connections, while I only have one per process.) The nature of the code that is running (php) doesn't really lend itself to closing open connections and whatnot. I can run the same code that he is executing with the same session data, and not result in a hanging process.

    Read the article

  • hadoop: port appears open locally but not remotelly

    - by miguel
    I am new to linux and hadoop and I am having the same issue as in this question. I think I understand what is causing it but I don't know how to solve it (Don't know what they mean by "Edit the Hadoop server's configuration file so that it includes its NIC's address."). The other post that they link says that the configuration files should refer to the machine's externally accessible host name. I think I got this right as every hadoop configuration file refers to "master" and the etc/hosts file lists the master by its private IP address. How can I solve this? Edit: I have 5 nodes: master, slavec, slaved, slavee and slavef all running debian. This is the hosts file in master: 127.0.0.1 master 10.0.1.201 slavec 10.0.1.202 slaved 10.0.1.203 slavee 10.0.1.204 slavef this is the hosts file in slavec (it looks similar in the other slaves): 10.0.1.200 master 127.0.0.1 slavec 10.0.1.202 slaved 10.0.1.203 slavee 10.0.1.204 slavef the masters file in master: master the slaves file in master: master slavec slaved slavee slavef the masters and slaves file in slavex has only one line: slavex

    Read the article

  • Share Point ACL on OSX Lion Server - Posix group always takes over ACLs

    - by Ben
    Trying to configure a share point on a Lion Server machine. The directory is created by the local server admin (serveradmin) and has rwxr-x--- given to it. The serveradmin user belongs to the local staff group so serveradmin readwrite staff group read Others none We have an OD group for all the employees (Workers) . Using the Server tool we've given Full Control to the share point: Workers Full Control serveradmin readwrite staff group read Others none We would assume that Workers could then do what they want on the share but that doesn't seem to be the case. It appears the POSIX permissions take over the ACL permissions for Worker. If I change the staff permission to readwrite then the Workers can create a file or folder in the share point. I would think the ACL should take over but it doesn't, posix always win, rendering ACL useless. Furthermore if I leave the readwrite permission for staff and take Write permission away for the Workers group then the posix group still wins. Essentially the Workers ACL does absolutely nothing. There are reports of similar problems in this Apple forum thread: https://discussions.apple.com/thread/3722901 The directory nesting fix suggested there doesn't work for us. Has anyone had similar issues and know how to fix this? Edit: in Workgroup Manager the employees user are set to primary group staff and given the additional OD group Workers. Changing their primary group doesn't help, it only shifts the problem onto Others taking over rights (logically) Edit 2: Ok, this is interesting, adding OD Users to the share's ACL works totally fine

    Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >