Search Results

Search found 16218 results on 649 pages for 'compiler errors'.

Page 115/649 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

• Network is not working anymore - Ubuntu 12.04

  - by Jonathan

  Network is not working anymore - Ubuntu 12.04 Hello, I have a problem with my network connection. I have been using the same laptop with Ubuntu and the same connection for more than a year, and suddenly yesterday the connection stopped working (both wireless and wired). I've tested with another computer and the connection is fine (both wireless and wired). I've been reading similar posts but I haven't found a solution yet. I tried a few commands that I'm posting here (my system is in spanish, so I have traslated it to english, maybe the terms are not accurate): grep -i eth /var/log/syslog | tail Jun 3 18:45:40 vanesa-pc NetworkManager[3584]: (eth0): now managed Jun 3 18:45:40 vanesa-pc NetworkManager[3584]: (eth0): device state change: unmanaged - unavailable (reason 'managed') [10 20 2] Jun 3 18:45:40 vanesa-pc NetworkManager[3584]: (eth0): bringing up device. Jun 3 18:45:40 vanesa-pc NetworkManager[3584]: (eth0): preparing device. Jun 3 18:45:40 vanesa-pc kernel: [ 7351.845743] forcedeth 0000:00:0a.0: irq 41 for MSI/MSI-X Jun 3 18:45:40 vanesa-pc kernel: [ 7351.845984] forcedeth 0000:00:0a.0: eth0: no link during initialization Jun 3 18:45:40 vanesa-pc kernel: [ 7351.847103] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 3 18:45:40 vanesa-pc NetworkManager[3584]: (eth0): deactivating device (reason 'managed') [2] Jun 3 18:45:40 vanesa-pc NetworkManager[3584]: Added default wired connection 'Wired connection 1' for /sys/devices/pci0000:00/0000:00:0a.0/net/eth0 Jun 3 18:45:40 vanesa-pc kernel: [ 7351.848817] ADDRCONF(NETDEV_UP): eth0: link is not ready ifconfig -a eth0 Link encap:Ethernet addressHW 00:1b:24:fc:a8:d1 ACTIVE BROADCAST MULTICAST MTU:1500 Metric:1 Packages RX:0 errors:16 lost:0 overruns:0 frame:16 Packages TX:123 errors:0 lost:0 overruns:0 carrier:0 colissions:0 length.tailTX:1000 Bytes RX:0 (0.0 B) TX bytes:26335 (26.3 KB) Interruption:41 Base address: 0x2000 lo Link encap:Local loop Inet address:127.0.0.1 Mask:255.0.0.0 Inet6 address: ::1/128 Scope:Host ACTIVE LOOP WORKING MTU:16436 Metrics:1 Packages RX:1550 errors:0 lost:0 overruns:0 frame:0 Packages TX:1550 errors:0 lost:0 overruns:0 carrier:0 colissions:0 long.tailTX:0 Bytes RX:125312 (125.3 KB) TX bytes:125312 (125.3 KB) iwconfig lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network *-network description: Ethernet interface product: MCP67 Ethernet manufacturer: NVIDIA Corporation Physical id: a bus information: pci@0000:00:0a.0 logical name: eth0 version: a2 series: 00:1b:24:fc:a8:d1 capacity: 100Mbit/s width: 32 bits clock: 66MHz capacities: pm msi ht bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=forcedeth driverversion=0.64 latency=0 link=no maxlatency=20 mingnt=1 multicast=yes port=MII resources: irq:41 memoria:f6288000-f6288fff ioport:30f8(size=8) memoria:f6289c00-f6289cff memoria:f6289800-f628980f lsmod Module Size Used by usbhid 41906 0 hid 77367 1 usbhid rfcomm 38139 0 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 bluetooth 158438 10 rfcomm,bnep binfmt_misc 17292 1 joydev 17393 0 hp_wmi 13652 0 sparse_keymap 13658 1 hp_wmi nouveau 708198 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197692 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau psmouse 87213 0 mxm_wmi 12859 1 nouveau serio_raw 13027 0 k8temp 12905 0 i2c_nforce2 12906 0 wmi 18744 2 hp_wmi,mxm_wmi video 19068 1 nouveau mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp forcedeth 58096 0 Let me know if I can give you more information. Thank you very much in advance, Jonathan

  Read the article

• Error Using 32 vs. 64 bit SharePoint 2007 DLLs with PowerShell

  - by Brian Jackett

  Next time you fire up PowerShell to work with the SharePoint API make sure you launch the proper bit version of PowerShell.  Last week I had an interesting error that led to this blog post.  Travel back in time a little bit with me to see where this 32 vs. 64 bit debate started. History     Ever since the first pre-beta bits of Office 2010 landed in my lap I have been questioning whether it’s better to run 32 or 64 bit applications on a 64 bit host operating system.  In relation to Office 2010 I heard a number of arguments for 32 bit including this link from the Office 2010 Engineering team.  Given my typical usage scenarios 32 bit seemed the way to go since I wasn’t a “super RAM hungry” Excel user or the like. The Problem     Since I had chosen 32 bit Office 2010, I tried to stick with 32 bit version of other programs that I run assuming the same benefits and rules applied to other applications.  This is where I was wrong.  Last week I was attempting to use 32 bit PowerShell ISE (Integrated Scripting Environment) on a 64 bit WSS 3.0 server.  When trying to reference the 64 bit SharePoint DLLs I got the following errors about not being able to find the web application.     I have run into these errors when I have hosts file issues or improper permissions to the farm / site collection but these were not the case.  After taking a quick spin around the interwebs I ran across the below forum post comment and another MSDN forum reply that explained the error.  Turns out that sometimes it’s not possible to run 32 bit applications against a 64 bit OS / farm / assembly / etc. …the problem could also be because your SharePoint is 64-Bit but your app is running in 32-bit mode     I quickly exited 32 bit PowerShell ISE and ran the same code under 64 bit PowerShell ISE.  All errors were gone and the script ran successfully.   Conclusion     The rules of 32 vs. 64 bit interoperability do not always apply evenly across all applications and scenarios.  In my case I wasn’t able to run 32 bit PowerShell against 64 bit SharePoint DLLs.  I’m updating all of my links and shortcuts to use 64 bit PowerShell where appropriate.  I’m quite surprised it has taken me this long to run into this error, but sometimes blind luck is all that keeps you from running into errors.  Lesson learned and hopefully this can benefit you as well.  Happy SharePointing all!         -Frog Out   Links http://blogs.technet.com/b/office2010/archive/2010/02/23/understanding-64-bit-office.aspx http://social.msdn.microsoft.com/Forums/en-US/sharepointdevelopment/thread/a732cb83-c2ef-4133-b04e-86477b72bbe3/ http://stackoverflow.com/questions/266255/filenotfoundexception-with-the-spsite-constructor-whats-the-problem

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• Source of (programmer) inefficiency

  - by Daniel

  I am interested to gain a better insight about the possible reasons of personal inefficiency as programmers (and only in programming) due to – simply - our own errors (because we are humans – well, almost all of us). I am not interested in how much we are productive or in how many adjustements the customer asks for when the work is done, but where and how each of us spend that part of its time in tasks that are unproductive and there is no one to blame except ourselves. Excluding ego - feeding and / or self – gratification, what I am trying to get (for all of us) is: what are the common issues eating our time; insight on reasons for that issues; identify simple way for us, personally (not delegating actions to other or our organizations), to correct our own problems. Please, do not think in academic terms but aim at the opportunity to compare our daily experiences and understand what are and how we try to fix our personal deficiencies. If you are interested to respond to this post, please: integrate the list if you see something important (or obvious) missing; highlight or name honestly your first issue tellng the way you try to address and solve your issue acting on yourself and yourself only in a sort of "continuous quality improving" My criteria for accepting the answer is: choose the best solution (feasibility and utility) to fix one (or more) of the problems of the list. Of course, selecting an error is not a vote on our skills: maybe we are hyper professional programmers and we lose ten minutes only every year or we are terribly inefficient, losing a couple of days a week: reasons for inefficiency could be really the same - but in a different scale. A possible list: Plain error in the names (variables, functions). Inability to see the obvious in your code. Misreading. Lack of concentration. Trying to use a technology you have not mastered. Errors with data types. Time required to understand your previous code or your documentation. Trying to do something more than requested because you enjoy it Using solutions more complicated than required because you enjoy it. Plain logical errors. Errors due to your fault in communications. Distraction My first personal issue: "Trying to use a technology you do not master." I have to use daily several technologies and I often need to spend significant time correcting code because my assumptions were plainly wrong. Reasons for this: production needs put high pressure and make difficult to find the time to learn. I try to address this reading technical books - as many as I can - even if this actually consumes a lot of time.

  Read the article

• Tips On Using The Service Contracts Import Program

  - by LuciaC

  Prior to release 12.1 there was no supported way to import contracts into the EBS Service Contracts application - there were no public APIs nor contract load programs provided.  From release 12.1 onwards the 'Service Contracts Import Program' is provided to load service contracts into the application. The Service Contracts Import functionality is explained in How to Use the Service Contracts Import Program - Scope and Limitations (Doc ID 1057242.1).  This note includes an attached document which explains the program architecture, shows the Entity Relationship Diagram and details the interface table definitions. The Import program takes data from the interface tables listed below and populates the contracts schema tables:  OKS_USAGE_COUNTERS_INTERFACE OKS_SALES_CREDITS_INTERFACEOKS_NOTES_INTERFACEOKS_LINES_INTERFACEOKS_HEADERS_INTERFACEOKS_COVERED_LEVELS_INTERFACEThese interface tables must be loaded via a custom load program.The Service Contracts Import concurrent request is then submitted to create contracts from this legacy data. The parameters to run the Import program are:  Parameter Description  Mode Validate only, Import  Batch Number Batch_Id (unique id populated into the OKS_HEADERS_INTERFACE table)  Number of Workers Number of workers required (these are spawned as separate sub-requests)  Commit size Represents number of successfully processed contracts commited to database The program spawns sub-requests for the import worker(s) and the 'Service Contracts Import Report'.  The data is validated prior to import and into the Contracts tables and will report errors in the Service Contracts Import Report program output file (Import Execution Report).  Troubleshooting tips are provided in R12.1 - Common Service Contract Import Errors (Doc ID 762545.1); this document lists some, but not all, import errors.  The document will be updated over time.  Additional help is given in Debugging Tip for Service Contracts Import Errors (Doc ID 971426.1).After you successfully import contracts, you can purge the records from the interface tables by running the Service Contracts Import Purge concurrent program. Note that there is no supported way to mass delete data from the Contracts schema tables once they are populated, so data loaded by the Import program must be fully tested and verified before the program is run to load data into a Production system.A Service Contracts Import Test program has been provided which will take an existing contract in the application and load the interface tables using the data from that contract.  This can be used as an example for guidance on how to load the interface tables.  The Test program functionality is explained in How to Use the Service Contracts Test Import Program Provided in Release 12.1 (Doc ID 761209.1).  Note that the Test program has some limitations which do not apply to the full Import program and is not a supported program, it is simply a testing tool.  

  Read the article

• Default Parameters vs Method Overloading

  - by João Angelo

  With default parameters introduced in C# 4.0 one might be tempted to abandon the old approach of providing method overloads to simulate default parameters. However, you must take in consideration that both techniques are not interchangeable since they show different behaviors in certain scenarios. For me the most relevant difference is that default parameters are a compile time feature while method overloading is a runtime feature. To illustrate these concepts let’s take a look at a complete, although a bit long, example. What you need to retain from the example is that static method Foo uses method overloading while static method Bar uses C# 4.0 default parameters. static void CreateCallerAssembly(string name) { // Caller class - Invokes Example.Foo() and Example.Bar() string callerCode = String.Concat( "using System;", "public class Caller", "{", " public void Print()", " {", " Console.WriteLine(Example.Foo());", " Console.WriteLine(Example.Bar());", " }", "}"); var parameters = new CompilerParameters(new[] { "system.dll", "Common.dll" }, name); new CSharpCodeProvider().CompileAssemblyFromSource(parameters, callerCode); } static void Main() { // Example class - Foo uses overloading while Bar uses C# 4.0 default parameters string exampleCode = String.Concat( "using System;", "public class Example", "{{", " public static string Foo() {{ return Foo(\"{0}\"); }}", " public static string Foo(string key) {{ return \"FOO-\" + key; }}", " public static string Bar(string key = \"{0}\") {{ return \"BAR-\" + key; }}", "}}"); var compiler = new CSharpCodeProvider(); var parameters = new CompilerParameters(new[] { "system.dll" }, "Common.dll"); // Build Common.dll with default value of "V1" compiler.CompileAssemblyFromSource(parameters, String.Format(exampleCode, "V1")); // Caller1 built against Common.dll that uses a default of "V1" CreateCallerAssembly("Caller1.dll"); // Rebuild Common.dll with default value of "V2" compiler.CompileAssemblyFromSource(parameters, String.Format(exampleCode, "V2")); // Caller2 built against Common.dll that uses a default of "V2" CreateCallerAssembly("Caller2.dll"); dynamic caller1 = Assembly.LoadFrom("Caller1.dll").CreateInstance("Caller"); dynamic caller2 = Assembly.LoadFrom("Caller2.dll").CreateInstance("Caller"); Console.WriteLine("Caller1.dll:"); caller1.Print(); Console.WriteLine("Caller2.dll:"); caller2.Print(); } And if you run this code you will get the following output: // Caller1.dll: // FOO-V2 // BAR-V1 // Caller2.dll: // FOO-V2 // BAR-V2 You see that even though Caller1.dll runs against the current Common.dll assembly where method Bar defines a default value of “V2″ the output show us the default value defined at the time Caller1.dll compiled against the first version of Common.dll. This happens because the compiler will copy the current default value to each method call, much in the same way a constant value (const keyword) is copied to a calling assembly and changes to it’s value will only be reflected if you rebuild the calling assembly again. The use of default parameters is also discouraged by Microsoft in public API’s as stated in (CA1026: Default parameters should not be used) code analysis rule.

  Read the article

• Ubuntu systematically losing wired connection

  - by Lukasz Baczynski

  I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

  Read the article

• Multiple vulnerabilities in Wireshark

  - by chandan

  CVE DescriptionCVSSv2 Base ScoreComponentProduct and Resolution CVE-2012-1593 Denial of Service (DoS) vulnerability 3.3 Wireshark Solaris 11 11/11 SRU 8.5 CVE-2012-1594 Improper Control of Generation of Code ('Code Injection') vulnerability 3.3 CVE-2012-1595 Resource Management Errors vulnerability 4.3 CVE-2012-1596 Resource Management Errors vulnerability 5.0 This notification describes vulnerabilities fixed in third-party components that are included in Sun's product distribution.Information about vulnerabilities affecting Oracle Sun products can be found on Oracle Critical Patch Updates and Security Alerts page.

  Read the article

• Ubuntu Server Cannot Route to the Internet

  - by ejes

  I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• Error on installing SVN extension with pecl

  - by thedp

  Hello, I'm trying to install the following PHP extension: http://php.net/manual/en/book.svn.php But when I do pecl install svn-beta I receive an error message that it can't locate the svn_client.h file. I searched the net but couldn't find any useful reference to this error. Thank you for your help. Installation result: root@myUbuntu:/home/thedp# pecl install svn-beta downloading svn-0.5.1.tgz ... Starting to download svn-0.5.1.tgz (23,563 bytes) .....done: 23,563 bytes 4 source files, building running: phpize Configuring for: PHP Api Version: 20041225 Zend Module Api No: 20060613 Zend Extension Api No: 220060519 1. Please provide the prefix of Subversion installation : autodetect 1-1, 'all', 'abort', or Enter to continue: 1. Please provide the prefix of the APR installation used with Subversion : autodetect 1-1, 'all', 'abort', or Enter to continue: building in /var/tmp/pear-build-root/svn-0.5.1 running: /tmp/pear/temp/svn/configure --with-svn --with-svn-apr checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for a sed that does not truncate output... /bin/sed checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking whether gcc and cc understand -c and -o together... yes checking for system library directory... lib checking if compiler supports -R... no checking if compiler supports -Wl,-rpath,... yes checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking target system type... i686-pc-linux-gnu checking for PHP prefix... /usr checking for PHP includes... -I/usr/include/php5 -I/usr/include/php5/main -I/usr/include/php5/TSRM -I/usr/include/php5/Zend -I/usr/include/php5/ext -I/usr/include/php5/ext/date/lib -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 checking for PHP extension directory... /usr/lib/php5/20060613+lfs checking for PHP installed headers prefix... /usr/include/php5 checking for re2c... no configure: WARNING: You will need re2c 0.12.0 or later if you want to regenerate PHP parsers. checking for gawk... no checking for nawk... nawk checking if nawk is broken... no checking for svn support... yes, shared checking for specifying the location of apr for svn... yes, shared checking for svn includes... configure: error: failed to find svn_client.h ERROR: `/tmp/pear/temp/svn/configure --with-svn --with-svn-apr' failed

  Read the article

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

• Managing Data Growth in SQL Server

  'Help, my database ate my disk drives!'. Many DBAs spend most of their time dealing with variations of the problem of database processes consuming too much disk space. This happens because of errors such as incorrect configurations for recovery models, data growth for large objects and queries that overtax TempDB resources. Rodney describes, with some feeling, the errors that can lead to this sort of crisis for the working DBA, and their solution.

  Read the article

• Multiple Resource Management Error vulnerabilities in libexpat

  - by chandan

  CVE DescriptionCVSSv2 Base ScoreComponentProduct and Resolution CVE-2012-0876 Resource Management Errors vulnerability 4.3 libexpat Solaris 10 SPARC: 137147-07 X86: 137148-07 Solaris 11 11/11 SRU 11.4 CVE-2012-1148 Resource Management Errors vulnerability 5.0 This notification describes vulnerabilities fixed in third-party components that are included in Oracle's product distributions.Information about vulnerabilities affecting Oracle products can be found on Oracle Critical Patch Updates and Security Alerts page.

  Read the article

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• Dell PowerEdge R720 - Corrupted RAID

  - by BT643

  Apologies in advance for the lengthy question. We have a Dell PowerEdge R720 server with: 2 x 136GB SAS drives in RAID 1 for the OS (Ubuntu Server 12.04) 6 x 3TB SATA drives in RAID 5 for data A few days ago we were getting errors when trying to access files on the large RAID 5 partition. We rebooted the server and got a message about the raid controller has found a foriegn config. We've had this before, and just needed to use Dell's RAID configuration utility to import foreign config on the RAID. Last time this worked, but this time, it started doing a disk check then we got this: FSCK has returned the following: "/dev/sdb1 inode 364738 has a bad extended attribute block 7 /dev/sdb1 unexpected inconsistency run fsck manually (i.e without -a or -p options) MOUNTALL fsck /ourdatapartition [1019] terminated with status 4 MOUNTALL filesystem has errors /ourdatapartition errors where found while checking the disk drive for /ourdatapartition Press F to fix errors, I to Ignore or M for Manual Recovery" We pressed F to try and fix the errors, but it eventually errored with: Inode 275841084, i_blocks is 167080, should be 0. Fix? yes Inode 275841141 has an invalid extend node (blk 2206761006, lblk 0) Clear? yes Inode 275841141, i_blocks is 227872, should be 0. Fix? yes Inode 275842303 has an invalid extend node (blk 2206760975, lblk 0) Clear? yes .... Error storing directory block information (inode=275906766, block=0, num=2699516178): Memory allocation failed /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** e2fsck: aborted /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** mountall: fsck /ourdatapartition [1286] terminated with status 9 mountall: Unrecoverable fsck error: /ourdatapartition We noticed one of the drive lights was not lit at all, and thought this may have failed and be the problem. We replaced the drive with a spare, and tried "F" to repair it again, but we keep just getting the same error as above. In the RAID configuration utility, all drives show as "online" and "optimal". We do have this data on another replicated server, so we're not worried about "recovering" anything, we just want to get the system back online asap. The server has 64 or 32GB memory, can't remember off the top of my head, but either way, with a 14TB RAID, I think it may still not be enough. Thanks EDIT - I checked the memory usage while fsck was running as suggested and after 2 or 3 minutes, it looked like this, using up nearly all of our servers memory: When it failed after 5 minutes or so with the error in my post, the memory immediately freed up again:

  Read the article

• Read-only filesystem

  - by János Harsányi

  I've resized a partition (ext4) from a Live CD with GParted, and after reboot it says that the file system is read-only. I've rebooted again from the CD and checked it with GParted with no errors. How could I find out why does it re-mount the file system in read-only mode? edit: It starts normally, but after some time, the "/" mount point gets remounted with read only settings, so I think it does have errors eventually. Is there any other way to repair it?

  Read the article

• Multiple Denial of Service (DoS) vulnerabilities in Apache Tomcat

  - by chandan

  CVE DescriptionCVSSv2 Base ScoreComponentProduct and Resolution CVE-2011-4858 Resource Management Errors vulnerability 5.0 Apache Tomcat Solaris 11 11/11 SRU 4 Solaris 10 SPARC: 122911-29 X86: 122912-29 Solaris 9 Contact Support CVE-2012-0022 Numeric Errors vulnerability 5.0 This notification describes vulnerabilities fixed in third-party components that are included in Sun's product distribution.Information about vulnerabilities affecting Oracle Sun products can be found on Oracle Critical Patch Updates and Security Alerts page.

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

• Tax Deducted At Source (TDS) for India Localizations

  - by LuciaC

  Do you have questions about TDS (Tax deducted at source) for India Localizations or want to know the latest information about this functionality? See Doc ID 1546099.1 TDS Tax Deduction at Source for India - Master Troubleshooting Guide. The document includes sections with the following information: Documentation and Setup of Tax Deduction at Source – this section contains a presentation with the configuration steps for the TDS feature Resolving errors – this section contains recommended patches and documents with solutions for specific errors Frequently asked questions  – See also our new FAQ Doc ID 1549522.1 for frequently asked questions about TDS.

  Read the article

• problem after login in wordpress site

  - by pankaj sharma

  I have installed WordPress first installation on Apache server Its opening fine but when i logged in with my user id and password http://examplesite.com/wp-login.php It is showing blank in Firefox and in IE page not open with no errors. I cleared all my browsers cache history still not able to open the page after login. There is no errors logs generated. wordpress version3.4.2 php 5.3.3 mysql 5.1.6

  Read the article

• Multiple Vulnerabilities in libpng

  - by chandan

  CVE DescriptionCVSSv2 Base ScoreComponentProduct and Resolution CVE-2010-0205 Resource Management Errors vulnerability 7.8 libpng Solaris 8 SPARC: 114816-04 X86: 114817-04 Solaris 9 SPARC: 139382-03 X86: 139383-03 Solaris 10 SPARC: 137080-05 X86: 137081-05 Solaris 11 Express snv_151a CVE-2010-1205 Buffer Overflow vulnerability 7.5 CVE-2010-2249 Resource Management Errors vulnerability 5.0 This notification describes vulnerabilities fixed in third-party components that are included in Sun's product distribution.Information about vulnerabilities affecting Oracle Sun products can be found on Oracle Critical Patch Updates and Security Alerts page.

  Read the article

• fdisk shows overlapping partitions

  - by Campa

  At every boot to start Ubuntu, a partition gets re-mounted more than 1 times, sometimes causing very long boots. Example below: > dmesg ... [ 21.472020] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro ... [ 42.021537] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 ... I suspect there is a problem of overlapping partitions here, regarding sda4 and sda5: > sudo fdisk -l Device Boot Start End Blocks Id System /dev/sda1 63 610469 305203+ de Dell Utility /dev/sda2 612352 32069631 15728640 7 HPFS/NTFS/exFAT /dev/sda3 * 32069632 238979788 103455078+ 7 HPFS/NTFS/exFAT /dev/sda4 238983166 625141759 193079297 5 Extended /dev/sda5 238983168 612630527 186823680 83 Linux /dev/sda6 612632576 625141759 6254592 82 Linux swap / Solaris Further details: > more /etc/fstab ... # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=b33be99b-5c9e-449e-ad48-be608aeff001 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=7c9071cc-b77b-40da-9f80-6b8a9a220cb1 none swap sw and > mount /dev/sda5 on / type ext4 (rw,errors=remount-ro,commit=0) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/piero/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=piero) I am Running Ubuntu Oneiric + LXDE on Dell Studio XPS machine 64-bit, dual booting with Windows 7. A months ago, I resized the Ubuntu partition and maybe I messed up something by doing that. Do you have any idea, why this long booting is happening?

  Read the article

• ClearTrace for SQL Server 2012

  - by Bill Graziano

  I’ve updated the beta for ClearTrace that support SQL Server 2012.  This requires SQL Server 2012 to be installed on the computer where ClearTrace is running.  It will read traces from SQL Server 2008 R2, SQL Server 2008 and SQL Server 2005. It includes some minor improvements in performance and handling large SQL statements. It should also give better errors. If you do find any of those errors, please report them in the support forum.

  Read the article

• Opscenter repair service times out. ERROR: Requested range intersects a local range [...]

  - by jlemire-zs

  My production cluster had the repair service enabled since april 16th with the default 9 days time to completion and repairs would complete properly. However, since may 22nd, it is being disabled automatically by Opscenter: From /var/log/opscenter/opscenterd.log: [...] 2014-06-03 21:13:47-0400 [zs_prod] ERROR: Repair task (<Node 10.1.0.22='6417880425364517165'>, (-4019838962446882275L, -4006140687792135587L), set(['zs_logging', 'OpsCenter'])) timed out after 3600 seconds. 2014-06-03 22:16:44-0400 [zs_prod] ERROR: Repair task (<Node 10.1.0.22='6417880425364517165'>, (-4006140687792135587L, -4006140687792135586L), set(['zs_logging', 'OpsCenter'])) timed out after 3600 seconds. 2014-06-03 22:16:44-0400 [zs_prod] ERROR: More than 100 errors during repair service, shutting down repair service 2014-06-03 22:16:44-0400 [zs_prod] INFO: Stopping repair service [...] From /var/log/opscenter/repair_service/zs_prod.log: [...] 2014-06-03 22:16:44-0400 [zs_prod] ERROR: Repair task (<Node 10.1.0.22='6417880425364517165'>, (-4006140687792135587L, -4006140687792135586L), set(['zs_logging', 'OpsCenter'])) timed out after 3600 seconds. 2014-06-03 22:16:44-0400 [zs_prod] ERROR: Task (<Node 10.1.0.22='6417880425364517165'>, (-4006140687792135587L, -4006140687792135586L), set(['zs_logging', 'OpsCenter'])) has failed 1 times. 2014-06-03 22:16:44-0400 [zs_prod] ERROR: 101 errors have ocurred out of 100 allowed. 2014-06-03 22:16:44-0400 [zs_prod] ERROR: More than 100 errors during repair service, shutting down repair service 2014-06-03 22:16:44-0400 [zs_prod] INFO: Stopping repair service On the nodes on which the repair fails, from /var/log/cassandra/system.log: ERROR [RMI TCP Connection(93502)-10.1.0.22] 2014-06-03 20:12:28,858 StorageService.java (line 2560) Repair session failed: java.lang.IllegalArgumentException: Requested range intersects a local range but is not fully contained in one; this would lead to i mprecise repair at org.apache.cassandra.service.ActiveRepairService.getNeighbors(ActiveRepairService.java:164) at org.apache.cassandra.repair.RepairSession.<init>(RepairSession.java:128) at org.apache.cassandra.repair.RepairSession.<init>(RepairSession.java:117) at org.apache.cassandra.service.ActiveRepairService.submitRepairSession(ActiveRepairService.java:97) at org.apache.cassandra.service.StorageService.forceKeyspaceRepair(StorageService.java:2620) at org.apache.cassandra.service.StorageService$5.runMayThrow(StorageService.java:2556) at org.apache.cassandra.utils.WrappedRunnable.run(WrappedRunnable.java:28) These errors, which only occurs if the repair service is running, are the only errors these nodes experience. Outside of the repair task, the Cassandra cluster works perfectly. I am running Opscenter 4.1.2 with a 6 nodes DSE 4.0.2 cluster installed on linux virtual machines. The nodes run a vanilla installation of Ubuntu Server 12.04 64-bit and DSE was installed and secured according to the provided installation documentation. I have been experiencing that problem on my development cluster for a while too (with DSE 4.0.0, 4.0.1 and 4.0.2), but I thought this was because of some configuration error on my part. The problem has appeared spontaneously at some point too. The Cassandra cluster has been working very smoothly with a good write throughput. It is very stable and has enough resources to work with. We did not notice any problems with the applications that depend on it.

  Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >