Search Results

Search found 3249 results on 130 pages for 'packet loss'.

Page 116/130 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

• Why can I view my site over a 3G connection but not through my wifi?

  - by Jonathan

  So, I am sitting in my office with four computers on the same network and internet connection. Two of the computers can visit this particular website. Two of the computer get a message "Google Chrome could not find". I have tried FF and IE also with the same problem. I can view the site 90% of the time on two of the working computers although the site seems slow and sometimes I also get the same errors as the other two computers. I have flushed the DNS, reset the router, tested the site on other peoples computers with success. Is this likely to be a site issue, an ISP issue, a hosting issue? Any advice is greatly appreciated. Here is the ping from the working machine: C:\Users\Jon>ping www.balihaicruises.com Pinging www.balihaicruises.com [208.113.173.102] with 32 bytes of data: Reply from 208.113.173.102: bytes=32 time=331ms TTL=47 Reply from 208.113.173.102: bytes=32 time=327ms TTL=47 Reply from 208.113.173.102: bytes=32 time=326ms TTL=47 Reply from 208.113.173.102: bytes=32 time=329ms TTL=47 Ping statistics for 208.113.173.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 326ms, Maximum = 331ms, Average = 328ms Traceroute: Tracing route to www.balihaicruises.com [208.113.173.102] over a maximum of 30 hops: 1 1 ms 17 ms 3 ms 192.168.1.1 2 42 ms 37 ms 36 ms 180.254.224.1 3 39 ms 47 ms 40 ms 180.252.1.69 4 36 ms 616 ms 57 ms 61.94.115.221 5 84 ms 76 ms 80 ms 180.240.191.98 6 73 ms 80 ms 72 ms 180.240.191.97 7 157 ms 143 ms 116 ms 180.240.190.82 8 115 ms 113 ms 120 ms ae1-123.hkg11.ip4.tinet.net [183.182.80.93] 9 331 ms 332 ms 335 ms xe-3-2-1.was14.ip4.tinet.net [89.149.184.30] 10 327 ms 330 ms 331 ms internap-gw.ip4.tinet.net [77.67.69.254] 11 437 ms 415 ms 350 ms border10.pc2-bbnet2.wdc002.pnap.net [216.52.127.73] 12 322 ms 823 ms 398 ms dreamhost-2.border10.wdc002.pnap.net [216.52.125.74] 13 328 ms 336 ms 326 ms ip-208-113-156-4.dreamhost.com [208.113.156.4] 14 326 ms 328 ms 336 ms ip-208-113-156-14.dreamhost.com [208.113.156.14] 15 327 ms 331 ms 333 ms apache2-udder.crisp.dreamhost.com [208.113.173.102] And then for the machine that doesn't work: C:\Users\Microsoft>ping www.balihaicruises.com Ping request could not find host www.balihaicruises.com. Please check the name and try again. C:\Users\Microsoft>tracert www.balihaicruises.com Unable to resolve target system name www.balihaicruises.com.

  Read the article

• No exception, no error, still i dont recieve the json object from my http post

  - by user2978538

  My source code: final Thread t = new Thread() { public void run() { Looper.prepare(); HttpClient client = new DefaultHttpClient(); HttpConnectionParams.setConnectionTimeout(client.getParams(), 10000); HttpResponse response; JSONObject obj = new JSONObject(); try { HttpPost post = new HttpPost("http://pc.dyndns-office.com/mobile.asp"); obj.put("Model", ReadIn1); obj.put("Product", ReadIn2); obj.put("Manufacturer", ReadIn3); obj.put("RELEASE", ReadIn4); obj.put("SERIAL", ReadIn5); obj.put("ID", ReadIn6); obj.put("ANDROID_ID", ReadIn7); obj.put("Language", ReadIn8); obj.put("BOARD", ReadIn9); obj.put("BOOTLOADER", ReadIn10); obj.put("BRAND", ReadIn11); obj.put("CPU_API", ReadIn12); obj.put("DISPLAY", ReadIn13); obj.put("FINGERPRINT", ReadIn14); obj.put("HARDWARE", ReadIn15); obj.put("UUID", ReadIn16); StringEntity se = new StringEntity(obj.toString()); se.setContentType(new BasicHeader(HTTP.CONTENT_TYPE, "application/json")); post.setEntity(se); post.setHeader("host", "http://pc.dyndns-office.com/mobile.asp"); response = client.execute(post); if (response != null) { InputStream in = response.getEntity().getContent(); } } catch (Exception e) { e.printStackTrace(); } Looper.loop(); } }; t.start(); } } i want to send an Json object to a Website. As far as I can see, I set the header, but still I get this exception, can someone help me? (I'm using Android-Studio) __ Edit: i don't get any exceptions anymore, but still i do not receive the json packet. When i manually call the website i get a log file entry. Does anyone know, what's wrong? Edit2: When i debug i get as response "HTTP/1.1 400 bad request" i'm sure its not an permission problem. Any ideas?

  Read the article

• How could I let Skydrive desktop sync to MicroSD in Windows 8 tablet?

  - by peSHIr

  I have a Samsung Slate 7 tablet with (now) Windows 8 on it. This machine has a 64 Gb SSD and I have a 64 Gb MicroSD card in it. I also have a Skydrive on my main Microsoft ID that contains about 45 Gb of content. With Windows and some development stuff installed, my Skydrive will not fit on the main drive of the tablet. (Besides, my idea was to keep data on the memory card anyway, to make it easier to repave the machine without data loss if need be.) My problem should now be clear: I want to install the Skydrive desktop app to sync my Skydrive to the MicroSD card. This is not possible, as Skydrive does not allow syncing files to removable drives. I have tried a number of things already, but none of them worked: Use the mklink command line tool to create a directory link/junction from a folder name on SSD to a folder on the MicroSD and then try to install Skydrive sync to the SSD link folder. Skydrive however still recognizes this as something it does not want to sync onto. The various different filter drivers mentioned on Agnipulse (including the Hitachi one) that should make windows see some or all of the removable drives in the system as fixed drives do not seem work on (64-bit) Windows 8: they either can't be installed, do nothing and/or cause Windows 8 to go into Automatic Repair mode when rebooting. The Lexar BootIt app seems to be meant to flip the relevant bit in the on-board drive controller of supported USB pen drives, but I tried it anyway. Of course it did nothing to how the MicroSD card was seen. I have now run out of ideas, it seems, and I was wondering if anyone here has a solution to let Windows 8 see the MicroSD memory card in my tablet as a fixed drive instead of removable drive, or some other way of getting the Skydrive desktop to sync my Skydrive data to that MicroSD card. And to be complete: this is not a duplicate question of this or this as those ask about getting USB drives multiple partitions to work on Windows XP. This question is specific about getting desktop Skydrive to sync to MicroSD card in Windows 8, which seems to be a question I have not seen on superuser so far.

  Read the article

• BOM in a PHP page auto generated by Wordpress

  - by Paolo63

  I admin two different blogs. They are both wordpress 2.8.6 (so they have exactly the same source code, plugins apart) but they are located on two different hosting platform (hostmonster.com and aruba.it). To explain my problem I've dumped with SmartSniff a session with each one of the sites. Here is the dump from hostmonster: GET /blog/paolo/ HTTP/1.1 Host: www.e-venturi.com Accept-Encoding: identity Accept-Language: en-us Accept: text/html, text/plain, text/xml, image/gif, image/x-xbitmap, image/x-icon,image/jpeg, image/pjpeg, application/vnd.ms-powerpoint, application/vnd.ms-excel, application/msword, */* User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.0;) HTTP/1.1 200 OK Date: Sat, 28 Nov 2009 23:47:38 GMT Server: Apache/2.2.14 (Unix) mod_ssl/2.2.14 OpenSSL/0.9.8l DAV/2 mod_auth_passthrough/2.1 FrontPage/5.0.2.2635 X-Powered-By: PHP/5.2.11 X-Pingback: http://www.e-venturi.com/blog/paolo/xmlrpc.php Vary: Accept-Encoding Transfer-Encoding: chunked Content-Type: text/html; charset=UTF-8 a6 <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> and now from aruba: GET /blog/ HTTP/1.1 Host: www.cubanite.net Accept-Encoding: identity Accept-Language: en-us Accept: text/html, text/plain, text/xml, image/gif, image/x-xbitmap, image/x-icon,image/jpeg, image/pjpeg, application/vnd.ms-powerpoint, application/vnd.ms-excel, application/msword, */* User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.0;) HTTP/1.1 200 OK Date: Sat, 28 Nov 2009 23:49:19 GMT Server: Apache/2.2 X-Pingback: http://www.cubanite.net/blog/xmlrpc.php Vary: Accept-Encoding Transfer-Encoding: chunked Content-Type: text/html; charset=UTF-8 100b ...<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> (note: a6 and 100b are the packet size reported by SmartSniff) Ok, the big difference are the three dots in front of the <!DOCTYPE in aruba. They are the UTF-8 BOM (0xef 0xbb 0xbf). Being the same PHP source on both the servers, why does it appears only on one server ? The content is generated so the post author can't deliberately insert a BOM and I've verified the template to be BOM free too. Naturally there are different PHP and Apache versions on the servers... what can I check or set to diagnose and resolve the problem ? By the way I don't want the BOM. Many thanks in advance.

  Read the article

• Given a trace of packets, how would you group them into flows?

  - by zxcvbnm

  I've tried it these ways so far: 1) Make a hash with the source IP/port and destination IP/port as keys. Each position in the hash is a list of packets. The hash is then saved in a file, with each flow separated by some special characters/line. Problem: Not enough memory for large traces. 2) Make a hash with the same key as above, but only keep in memory the file handles. Each packet is then put into the hash[key] that points to the right file. Problems: Too many flows/files (~200k) and it might run out of memory as well. 3) Hash the source IP/port and destination IP/port, then put the info inside a file. The difference between 2 and 3 is that here the files are opened and closed for each operation, so I don't have to worry about running out of memory because I opened too many at the same time. Problems: WAY too slow, same number of files as 2 so also impractical. 4) Make a hash of the source IP/port pairs and then iterate over the whole trace for each flow. Take the packets that are part of that flow and place them into the output file. Problem: Suppose I have a 60 MB trace that has 200k flows. This way, I would process, say, a 60 MB file 200k times. Maybe removing the packets as I iterate would make it not so painful, but so far I'm not sure this would be a good solution. 5) Split them by IP source/destination and then create a single file for each one, separating the flows by special characters. Still too many files (+50k). Right now I'm using Ruby to do it, which might've been a bad idea, I guess. Currently I've filtered the traces with tshark so that they only have relevant info, so I can't really make them any smaller. I thought about loading everything in memory as described in 1) using C#/Java/C++, but I was wondering if there wouldn't be a better approach here, especially since I might also run out of memory later on even with a more efficient language if I have to use larger traces. In summary, the problem I'm facing is that I either have too many files or that I run out of memory. I've also tried searching for some tool to filter the info, but I don't think there is one. The ones I've found only return some statistics and wouldn't scan for every flow as I need.

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• Ubuntu with KVM guest VM and broken bridges

  - by MadPsy

  I have an Ubuntu box with a KVM guest VM running. They use bridging so the guest VM attaches to the physical network of its host. The guest VM has 2 NICs in 2 different bridges. First NIC of the VM is tap5 and is in bridge br0 br0 8000.46720f5c572e no eth0.500 tap5 Second NIC of the VM is tap2 and is in bridge br100 br100 8000.76ad2fc96661 no eth0.100 eth0.101 eth0.103 eth0.104 eth0.105 tap2 On the host, br0 has an IP and br100 does not 21: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 46:72:0f:5c:57:2e brd ff:ff:ff:ff:ff:ff inet 192.168.100.4/24 brd 192.168.10.255 scope global br0 inet6 fe80::d6ae:52ff:febe:777/64 scope link valid_lft forever preferred_lft forever On the guest, its eth0 and eth1 interfaces both have IP addresses 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:da brd ff:ff:ff:ff:ff:ff inet 192.168.100.6/24 brd 192.168.100.255 scope global eth0 inet6 fe80::23e:61ff:fefb:7ada/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:ea brd ff:ff:ff:ff:ff:ff inet 172.16.50.129/25 brd 172.16.50.255 scope global eth1 inet6 fe80::23e:61ff:fefb:7aea/64 scope link valid_lft forever preferred_lft forever On the guest VM, a tcpdump of its eth1 interface (tap2) shows traffic from its eth0 interface (tap5), as if the 2 bridges are themselves bridged. This means any interface on br100 is now bridged across to br0 - which is completely broken. root@chillispot:~# tcpdump -c 1 -n -v -i eth1 net 192.168.100.0/24 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 16:31:24.175583 IP (tos 0x0, ttl 64, id 48054, offset 0, flags [DF], proto TCP (6), length 148) 192.168.100.6.22 > 192.168.100.4.59505: Flags [P.], cksum 0x6c2b (correct), seq 1056321648:1056321744, ack 398642983, win 1700, options [nop,nop,TS val 197473436 ecr 200655363], length 96 What could be bridging the 2 bridges, except the guest VM (which is a stock Ubuntu install)? I am at a complete loss! Thanks.

  Read the article

• How to configure the framesize using AudioUnit.framework on iOS

  - by Piperoman

  I have an audio app i need to capture mic samples to encode into mp3 with ffmpeg First configure the audio: /** * We need to specifie our format on which we want to work. * We use Linear PCM cause its uncompressed and we work on raw data. * for more informations check. * * We want 16 bits, 2 bytes (short bytes) per packet/frames at 8khz */ AudioStreamBasicDescription audioFormat; audioFormat.mSampleRate = SAMPLE_RATE; audioFormat.mFormatID = kAudioFormatLinearPCM; audioFormat.mFormatFlags = kAudioFormatFlagIsPacked | kAudioFormatFlagIsSignedInteger; audioFormat.mFramesPerPacket = 1; audioFormat.mChannelsPerFrame = 1; audioFormat.mBitsPerChannel = audioFormat.mChannelsPerFrame*sizeof(SInt16)*8; audioFormat.mBytesPerPacket = audioFormat.mChannelsPerFrame*sizeof(SInt16); audioFormat.mBytesPerFrame = audioFormat.mChannelsPerFrame*sizeof(SInt16); The recording callback is: static OSStatus recordingCallback(void *inRefCon, AudioUnitRenderActionFlags *ioActionFlags, const AudioTimeStamp *inTimeStamp, UInt32 inBusNumber, UInt32 inNumberFrames, AudioBufferList *ioData) { NSLog(@"Log record: %lu", inBusNumber); NSLog(@"Log record: %lu", inNumberFrames); NSLog(@"Log record: %lu", (UInt32)inTimeStamp); // the data gets rendered here AudioBuffer buffer; // a variable where we check the status OSStatus status; /** This is the reference to the object who owns the callback. */ AudioProcessor *audioProcessor = (__bridge AudioProcessor*) inRefCon; /** on this point we define the number of channels, which is mono for the iphone. the number of frames is usally 512 or 1024. */ buffer.mDataByteSize = inNumberFrames * sizeof(SInt16); // sample size buffer.mNumberChannels = 1; // one channel buffer.mData = malloc( inNumberFrames * sizeof(SInt16) ); // buffer size // we put our buffer into a bufferlist array for rendering AudioBufferList bufferList; bufferList.mNumberBuffers = 1; bufferList.mBuffers[0] = buffer; // render input and check for error status = AudioUnitRender([audioProcessor audioUnit], ioActionFlags, inTimeStamp, inBusNumber, inNumberFrames, &bufferList); [audioProcessor hasError:status:__FILE__:__LINE__]; // process the bufferlist in the audio processor [audioProcessor processBuffer:&bufferList]; // clean up the buffer free(bufferList.mBuffers[0].mData); //NSLog(@"RECORD"); return noErr; } With data: inBusNumber = 1 inNumberFrames = 1024 inTimeStamp = 80444304 // All the time same inTimeStamp, this is strange However, the framesize that i need to encode mp3 is 1152. How can i configure it? If i do buffering, that implies a delay, but i would like to avoid this because is a real time app. If i use this configuration, each buffer i get trash trailing samples, 1152 - 1024 = 128 bad samples. All samples are SInt16.

  Read the article

• Intel RST accidentally selected wrong drive as system drive -- how to fix?

  - by Sean Killeen

  Question / TL;DR If Intel RST has marked a drive other than my RAID set as the system drive, how can I get it so that the RAID set is now seen as the system drive, and catch it up to my drive now? What Happened NOTE: Some perhaps unwise decisions are ahead. This is as best as I can recall the order of things. I had a 2x1TB RAID1 config. I bought the drives around the same time, and they started to die around the same time. I replaced 1st drive with a 2 TB drive before the other one's SMART errors got more serious. I waited for the RAID to replicate, then replaced the 2nd drive with a manufacturer's replacement. I got a second manufacturer's drive replacement and used it as a spare. so I now I had a 1TB/2TB drive in a RAID1 and another 1TB as a spare. The 1TB drive in the replacement set was bad from the manufacturer. Rather than mess with their refurbished stuff, I bought another 2 TB drive an upped the config to a 2x2TB RAID1 with the other, functioning manufacturer's drive as a spare. I made the mistake of trying to bring the other drive online to clean it out and the signatue clash killed my machine. When the machine rebooted, that drive was marked as the system drive. So, I have a 2x2TB RAID1 that is apparently offline, and 1 spare 1 TB refurbished drive that everything is being run from. Not a great idea. Options I'm considering Bring the 2x2TB drive back online, and then unplug the spare until I can format it in another system. This would involve some data loss, but the more I think about it, I actually think I haven't modified any data that isn't backed up or synced somewhere (go me!) Anything that isn't is likely trivial, enough that I'm willing to take the risk. One downside here is that if the 2 TB doesn't have data on it for some reason, I could be screwed trying to put the other drive back in, no? Try to somehow get the RAID1 updated with the data from the current system drive. Option 3?

  Read the article

• IIS httpTracing setting has no effect

  - by digahill

  I'm trying to troubleshoot some performance issues we are having on a specific ASP.NET page with Microsoft's Perfecto Tool on IIS 7.5. Perfecto uses the ETW hooks build in to IIS to report on specific HTTP request, and is working quite well. However, I only want IIS to emit traces for one specific page, say "Default.aspx" in my TestApp Web Application. Following the instructions on the httpTracing man page, I should be able to add the traceUrls element to my root web.config file for TestApp. This doesn't seem to affect tracing whatsoever when I do so. For example, I've used the following settings in the web.config file and every request that hits the IIS server is sending tracing messages that are in turn picked up by Perfecto. (In the System.WebServer section) <httpTracing> <traceUrls> <add value="/Default.aspx" /> </traceUrls> </httpTracing> I then found that the applicationHost.config file on the server had an empty element. I tried removing this element, as well as the httpTracing element in the web.config. After a machine reboot, I was still getting tracing messages! My understanding is that the presense of the httpTracing element is what controlls whether ETW tracing is on or not. I ensured there was no reference to httpTracing in the machine.config, too. At a loss, I decided to remove the IIS Tracing feature with Server Manager. After a reboot, I no longer got ETW tracing. I then reinstalled IIS Tracing feature with Server Manager. As expected, the httpTracing element reappeared in the applicationhost.config file. Tracing messages began sending again for all sites and pages. I then tried to use the traceUrls element at the applicationhost.config level. This also didn't filter out and traces. I must be misunderstanting something key with how httpTracing works. There aren't many resources on the web to help me, either. Can anyone tell me if what I'm trying should work? Has anyone else had success filtering tracing message per page with traceUrls? I should note that I also tried changing with the following setting in applicationhost.config to "allow". It didn't seem to help. <section name="httpTracing" overrideModeDefault="Allow" />

  Read the article

• Poor performance of single processor 32bit Windows XP xompared SMP in VBA+Excel

  - by Adam Ryczkowski

  Welcome! On many computers I experienced poor performance of 32 bit guests running on 64 bit Linux host (I used only the Debian family). At last I managed to collect benchmark data. I made the benchmark by running custom VBA macro, (which we use in our company) that generates 284 pages long Word document full of Excel Pie charts, tables and comments. The macro is run as a single task (excluding the standard services) on a set of identically configured Windows XP 32-bit systems. I measured the time (in sec.) needed to perform the test. The computer (i.e. my notebook Asus P53E) supports both VT-d extensions and native Windows XP. It has 2-core processor, each core is hyperthreaded, so in total we have 4 mostly independent execution units. I use the latest VirtualBox 4.2 and VMWare Workstation 9.0 for Linux, installed together on the same host (running Mint 13 Maya) but never run simultaneously. The results (in column Time) are no less accurate than ± 10% Here are the results (sorry for the format, but I couldn't find out a better solution for tables in SO): +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ | Host software | # processor | Windows kernel | IO APIC | VT-x/AMD-V | 2D Video Accel | Time | +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 1 | 0 | 1139 | | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 1 | 1 | 1050 | | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 0 | 1 | 1644 | | VirtualBox | 4 | ACPI Multiprocessor PC | 1 | 1 | 1 | 6809 | | VMWare | 1 | ACPI Uniprocessor PC | | 1 | 1 | 1175 | | VMWare | 4 | ACPI Multiprocessor PC | | 1 | 1 | 3412 | | Native | 4 | ACPI Multiprocessor PC | | | | 1693 | | Native | 1 | Advanced Configuration and Power Interface (ACPI) PC | | | | 1170 | +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ Here are the striking conclusions: Although I've read in the VirtualBox fora about abysmal performance with 32-bit guest on 64-bit host, VMWare also has problems compared to native run, still being twice faster(!) than VBox. Although VBA is inherently single-threaded, the Excel calculations, which take much more than a half of total computation time, supposedly aren't. So one would expect some speed gain when running on 2+ cores ("+" for hyperthreading). What we see is a speed loss. And quite big one too. For the VirtualBox the VT-d extension isn't a big deal. Can anyone shed some light on why the singlethreaded Windows kernel is so much faster than the SMP one?

  Read the article

• Problem with tcp server when converting to service

  - by djerry

  Hello lads, I'm working on monitoring some object (cdr-packets). I'm setting up a tcp-server and am listening on port 50043 for the packages. The program as a console application is working just fine, my server is working like it should and i'm receiving the packets. When i try to use it as a service, i cannot seem to get a client connected to my server. Is there something i need to change to deploy this as a service? Code below is from my application: this is my service class where i start protected override void OnStart(string[] args) { server = new TcpServer(); server.StartServer(); } this is the constructor of TcpServer public TcpServer() { try { _server = new TcpListener(IPAddress.Any, 50043); } catch (Exception) { _server = null; } } this is the method i call after initialising the class public void StartServer() { if (_server != null) { // Create a ArrayList for storing SocketListeners before starting the server. _socketListenersList = new ArrayList(); // Start the Server and start the thread to listen client requests. _server.Start(); _serverThread = new Thread(new ThreadStart(ServerThreadStart)); _serverThread.Start(); // Create a low priority thread that checks and deletes client // SocktConnection objcts that are marked for deletion. _purgingThread = new Thread(new ThreadStart(PurgingThreadStart)); _purgingThread.Priority = ThreadPriority.Lowest; _purgingThread.Start(); } } this is the thread that keep checking if any client tries to connect private void ServerThreadStart() { // Client Socket variable; Socket clientSocket = null; TcpSocketListener socketListener = null; while (!_stopServer) { try { // Wait for any client requests and if there is any request from any //client accept it (Wait indefinitely). clientSocket = _server.AcceptSocket(); // Create a SocketListener object for the client. socketListener = new TcpSocketListener(clientSocket); // Add the socket listener to an array list in a thread safe fashon. lock (_socketListenersList) { _socketListenersList.Add(socketListener); } // Start a communicating with the client in a different thread. socketListener.StartSocketListener(); } catch (SocketException se) { _stopServer = true; } } } when for the first time a packet waits to be read, and i get to "clientSocket = _server.AcceptSocket();", it throws an exception (service, not very good debugable) Does anyone recognize this problem or can help me? Thanks in advance

  Read the article

• WiFi signal is lost every 3 minutes

  - by Software Monkey

  For several weeks now my Android phone has been losing it's WiFi signal momentarily, typically at about 3 minute intervals (about 3 minutes, 1.5 seconds) and occasionally at some longer interval that always seems to be just over 3 minutes. This causes an interruption of several seconds while the WiFi connection is re-established and typically fails any kind of download/streaming that is happening, makes web sites "unreachable" and generally makes the phone unusable as a data device due to the frequency. The signal remains down for about a second, but the phone takes a few more seconds to reconnect to the router. This happens regardless of proximity to the router, which otherwise show a very strong signal - usually -40 to -30 dBm or better in the same room, nowhere less than 060 dBm anywhere in the house. Changing channels does not help (I've tried 1, 4, 8 and 9). Nor does turning off the router's guest access. Nor does turning off the 5.0 GHz band. Monitoring the signal on my phone with WiFi analyzer, shows all WiFi signals on all channels drop to nothing when the WiFi connection is lost (there are two other networks on different channels which are strong enough to be relevant, with about 6 others constantly fading in and out). WiFi analyzer shows 3 separate signals for my router, the main 2.4 GHz, the guest 2.4 GHz and the 5.0 GHz. Using WiFi Analyzer on my wife's phone side-by-side shows no change in signal when my phone drops, nor does her phone drop. Monitoring the signal using our laptop, side-by-side likewise shows no signal loss and likewise the laptop does not lose it's WiFi connection. But, at work, the phone seems to not exhibit the same behavior, or, if it does, it's very occasional. Monitoring it all day at work I only saw the signal drop 3 or 4 times. The signal strength of the various networks there is comparatively weak. AT&T were super helpful: "Sorry, we can't help you with WiFi problems. You could try doing a factory reset on your phone". </sarcasm The router is relatively new, but has been working fine with this phone since last Dec. Phone : Motorola Atrix (about 8 months old). Router : Belkin N750 DB (F9K1103 v1 (01C)). Router Firmware: 1.00.46 (2011/10/28 6:37:11). Security : WPA/WPA2-Personal (PSK)

  Read the article

• unable to access a NAT'ed IP via a VPN on Windows 7

  - by crmpicco

  I connect to a range of servers hosted by one provider via a VPN. I can connect to the VPN fine, however when I then go and try and connect to the server(s) it fails. A NAT'ed IP address that has worked up until today, has stopped working either via SSH/SFTP. As you can see below, if I try and ping the IP then it responds with Destination host unreachable, but, for some reason it says the reply is from 192.168.0.8? If it enter this IP address in my browser, I get nothing. Where is this IP coming from and is there any good reason why I cannot access the IP I am trying to ping? C:\Users\crmpicco>ping 172.26.100.x Pinging 172.26.100.x with 32 bytes of data: Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Ping statistics for 172.26.100.x: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), I have the VPN remote host address of 80.75.67.x, which shows me as being connected. But i'm unsure if there is a config issue at the server side or my end that has caused this issue? I have had some recent Win7 (automatic) updates, but it's hard to tell if that's caused this problem. This is my output from arp: C:\Users\cmorton>arp -a Interface: 192.168.0.8 --- 0xe Internet Address Physical Address Type 192.168.0.1 00-18-4d-b9-68-5e dynami 192.168.0.6 00-f4-b9-68-0c-9a dynami 192.168.0.7 08-00-27-f2-9f-d6 dynami 192.168.0.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.251 01-00-5e-00-00-fb static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 192.168.56.1 --- 0x15 Internet Address Physical Address Type 192.168.56.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.251 01-00-5e-00-00-fb static 224.0.0.252 01-00-5e-00-00-fc static 255.255.255.255 ff-ff-ff-ff-ff-ff static

  Read the article

• Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

  - by John C

  I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

  Read the article

• Nginx fastcgi problems with django

  - by wizard

  I'm deploying my first django app. I'm familiar with nginx and fastcgi from deploying php-fpm. I can't get python to recognize the urls. I'm also at a loss on how to debug this further. I'd welcome solutions to this problem and tips on debugging fastcgi problems. Currently I get a 404 page regardless of the url and for some reason a double slash For http://www.site.com/admin/ Page not found (404) Request Method: GET Request URL: http://www.site.com/admin// My urls.py from the debug output - which work in the dev server. Using the URLconf defined in ahrlty.urls, Django tried these URL patterns, in this order: ^listings/ ^admin/ ^accounts/login/$ ^accounts/logout/$ my nginx config server { listen 80; server_name beta.ahrlty.com; access_log /home/ahrlty/ahrlty/logs/access.log; error_log /home/ahrlty/ahrlty/logs/error.log; location /static/ { alias /home/ahrlty/ahrlty/ahrlty/static/; break; } location /media/ { alias /usr/lib/python2.6/dist-packages/django/contrib/admin/media/; break; } location / { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:8001; break; } } and my fastcgi_params fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param PATH_INFO $fastcgi_script_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; And lastly I'm running fastcgi from the commandline with django's manage.py. python manage.py runfcgi method=threaded host=127.0.0.1 port=8080 pidfile=mysite.pid minspare=4 maxspare=30 daemonize=false I'm having a hard time debugging this one. Does anything jump out at anybody?

  Read the article

• What the best way to achieve RPO of zero and lowest possible RTO (less than 15 minutes) with SQL 2008 R2?

  - by Adrian Hope-Bailie

  We are running a payments (EFT transaction processing) application which is processing high volumes of transactions 24/7 and are currently investigating a better way of doing DB replication to our disaster recovery site. Our current and previous strategies have included using both DoubleTake and Redgate to replicate data to a warm stand-by. DoubleTake is the supported solution from the payments software vendor however their (DoubleTake's) support in South Africa is very poor. We had a few issues and simply couldn't ever resolve them so we had to give up on DoubleTake. We have been using Redgate to manually read the data from the primary site (via queries) and write to the DR site but this is: A bad solution Getting the software vendor hot and bothered whenever we have support issues as it has a tendency to interfere with the payment application which is very DB intensive. We recently upgraded the whole system to run on SQL 2008 R2 Enterprise which means we should probably be looking at using some of the built-in replication features. The server has 2 fairly large databases with a mixture of tables containing highly volatile transactional data and pretty static configuration data. Replication would be done over a WAN link to a separate physical site and needs to achieve the following objectives. RPO: Zero loss - This is transactional data with financial impact so we can't lose anything. RTO: Tending to zero - The business depends on our ability to process transactions every minute we are down we are losing money I have looked at a few of the other questions/answers but none meet our case exactly: SQL Server 2008 failover strategy - Log shipping or replication? How to achieve the following RTO & RPO with logshipping only using SQL Server? What is the best of two approaches to achieve DB Replication? My current thinking is that we should use mirroring but I am concerned that for RPO:0 we will need to do delayed commits and this could impact the performance of the primary DB which is not an option. Our current DR process is to: Stop incoming traffic to the primary site and allow all in-flight transaction to complete. Allow the replication to DR to complete. Change network routing to route to DR site. Start all applications and services on the secondary site (Ideally we can change this to a warmer stand-by whereby the applications are already running but not processing any transactions). In other words the DR database needs to, as quickly as possible, catch up with primary and be ready for processing as the new primary. We would then need to be able to reverse this when we are ready to switch back. Is there a better option than mirroring (should we be doing log-shipping too) and can anyone suggest other considerations that we should keep in mind?

  Read the article

• SQL Server database filled the hard drive and freeing up space isn't possible

  - by Jon

  I have a database in SQL Server 2008 on a 1Tb hard drive and it filled the drive, there is only 4Kb free. The MDF file is 323Gb and the LDF is 653Gb. The hard disk this DB is on has no other files on it other than the MDF and LDF so it's impossible to free up any space on the drive. The main hard disk is smaller but there is enough room to transfer the MDF to that drive, in case that helps. This server is overseas at a customer site and it's not possible at the moment to add more disk space to the server. It's also not possible to delete any records because the DB is in a failed mode (due to no disk space) and it doesn't respond to most commands. The Db is currently in full recovery mode which is why the LDF file is so large. This DB really doesn't need to be in full recovery so going forward we plan on switching it to simple mode which will save us a lot of space. I also don't care about losing the LDF file, but I need all of the data. I've spent a lot of time looking for a way out of this problem but everything I've found first involves either freeing up disk space or adding more disk space, neither of which is an option at this time. I'm stuck and any help would be greatly appreciated. I get the following log when trying to switch the DB to online mode. Msg 945, Level 14, State 2, Line 3 Database 'DBNAME' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. Msg 5069, Level 16, State 1, Line 3 ALTER DATABASE statement failed. Msg 1101, Level 17, State 12, Line 3 Could not allocate a new page for database 'DBNAME' because of insufficient disk space in filegroup 'DEFAULT'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. I've found the following solutions but none work due to having no disk space on that drive, and since the DB is in a failed state I can't run most commmands. - DBCC SHRINKFILE - can't be run because doing a 'use DBNAME' fails - Detaching the DB and then changing the location of the MDF/LDF files, this fails because the DB is in an offline mode so you can't run detach. I'm at a loss about what else to try. Thanks.

  Read the article

• How can I send multiple types of objects across Protobuf?

  - by cyclotis04

  I'm implementing a client-server application, and am looking into various ways to serialize and transmit data. I began working with Xml Serializers, which worked rather well, but generate data slowly, and make large objects, especially when they need to be sent over the net. So I started looking into Protobuf, and protobuf-net. My problem lies in the fact that protobuf doesn't sent type information with it. With Xml Serializers, I was able to build a wrapper which would send and receive any various (serializable) object over the same stream, since object serialized into Xml contain the type name of the object. ObjectSocket socket = new ObjectSocket(); socket.AddTypeHandler(typeof(string)); // Tells the socket the types socket.AddTypeHandler(typeof(int)); // of objects we will want socket.AddTypeHandler(typeof(bool)); // to send and receive. socket.AddTypeHandler(typeof(Person)); // When it gets data, it looks for socket.AddTypeHandler(typeof(Address)); // these types in the Xml, then uses // the appropriate serializer. socket.Connect(_host, _port); socket.Send(new Person() { ... }); socket.Send(new Address() { ... }); ... Object o = socket.Read(); Type oType = o.GetType(); if (oType == typeof(Person)) HandlePerson(o as Person); else if (oType == typeof(Address)) HandleAddress(o as Address); ... I've considered a few solutions to this, including creating a master "state" type class, which is the only type of object sent over my socket. This moves away from the functionality I've worked out with Xml Serializers, though, so I'd like to avoid that direction. The second option would be to wrap protobuf objects in some type of wrapper, which defines the type of object. (This wrapper would also include information such as packet ID, and destination.) It seems silly to use protobuf-net to serialize an object, then stick that stream between Xml tags, but I've considered it. Is there an easy way to get this functionality out of protobuf or protobuf-net? I've come up with a third solution, and posted it below, but if you have a better one, please post it too!

  Read the article

• Can't find windows 2000 domain after PDC Change

  - by Mark A Kruger

  This is a windows 2000 domain issue. I had an old win2000 PDC that was beginning to fail. So, trying to be pre-emptive, I installed a new BDC, then "demoted" the old PDC and took it off the network. Now it appears that no member server can "find" the domain anymore. No logins work (for services or a RDP or anything). What I've tried (based on googling): Verified sysvol is shared on all servers. Used nslookup to verify that DC's are being found. netdiag /fix meta data cleanup routines. verified no firewall issues (port 389 etc) seizing all roles to new PDC (I did that as part of the original promotion). LMHOST file and Netbios settings. At the moment it seems like I can get the DC's returned but cannot contact them. I'm at a loss. My latest attempt was to remove a member server from the domain and try to "re-add" it. When I do that I get this message: The query was for the SRV record for _ldap._tcp.dc._msdcs.cfwebtools.com The following domain controllers were identified by the query: db-dev1.cfwebtools.com file-prod1.cfwebtools.com cfwt-pdc2.cfwebtools.com However no domain controllers could be contacted. It then goes on to ask if I've checked my A record and made sure they are running. Is there a way to force this domain to be seen? I also shared sysvol (or double checked it) and restarted the dfsr service. More information. I got looking at sysvol and found it was not shared on 2 of these servers. Only one of them (db-dev1) has a "good" or at least "populated" sys vol store. So I tried doing a "d2" recovery of my PDC against that good sysvol. But it never synchs - or at least it does not seem to synch. I'm guessing if I could get sysvol and netlogin to kick in and replicate that would fix my issue. I think these DC's aren't responding because they are waiting for replication which is broken somehow. Would taking down all the DC's except for db-dev1 fix the issue - at least temporarily? I know I can't just copy the sysvol stuff over to the other 2 can I?

  Read the article

• waiting for 2 different events in a single thread

  - by João Portela

  component A (in C++) - is blocked waiting for alarm signals (not relevant) and IO signals (1 udp socket). has one handler for each of these. component B (java) - has to receive the same information the component A udp socket receives. periodicaly gives instructions that should be sent through component A udp socket. How to join both components? it is strongly desirable that: the changes to attach component B to component A are minimal (its not my code and it is not very pleasent to mess with). the time taken by the new operations (usually communicating with component B) interfere very little with the usual processing time of component A - this means that if the operations are going to take a "some" time I would rather use a thread or something to do them. note: since component A receives udp packets more frequently that it has component B instructions to forward, if necessary, it can only forward the instructions (when available) from the IO handler. my initial ideia was to develop a component C (in C++) that would sit inside the component A code (is this called an adapter?) that when instanciated starts the java process and makes the necessary connections (that not so little overhead in the initialization is not a problem). It would have 2 stacks, one for the data to give component B (lets call it Bstack) and for the data to give component A (lets call it Astack). It would sit on its thread (lets call it new-thread) waiting for data to be available in Bstack to send it over udp, and listen on the udp socket to put data on the Astack. This means that the changes to component A are only: when it receives a new UDP packet put it on the Bstack, and if there is something on the Astack sent it over its UDP socket (I decided for this because this socket would only be used in the main thread). One of the problems is that I don't know how to wait for both of these events at the same time using only one thread. so my questions are: Do I really need to use the main thread to send the data over component A socket or can I do it from the new-thread? (I think the answer is no, but I'm not sure about race conditions on sockets) how to I wait for both events? boost::condition_variable or something similar seems the solution in the case of the stack and boost::asio::io_service io_service.run() seems like the thing to use for the socket. Is there any other alternative solution for this problem that I'm not aware of? Thanks for reading this long text but I really wanted you to understand the problem.

  Read the article

• Apache returns 403 Forbidden for alternative port vhost

  - by Wesley

  I'm having an issue getting vhosts to work on Apache 2.2, Debian 6. I have two VirtualHosts, one on port 80 and one on port 8888. The port 80 one has been created automatically by DirectAdmin, the 8888 is a custom one. It's configuration is as follows. <VirtualHost *:8888 > DocumentRoot /home/user/public_html/development ServerName www.myserver.nl ServerAlias myserver.nl <Directory "/home/user/public_html/development"> Options +Indexes +FollowSymLinks +MultiViews AllowOverride All Order Allow,deny Allow from all </Directory> </VirtualHost> Of course I also have a NameVirtualHost *:8888 The port 80 DocumentRoot is /home/user/public_html/production, which is perfectly accessible and works like a charm. The port 8888 docroot of /home/user/public_html/development is 403 forbidden though. I have compared the permissions for both folders. They seem fine to me. drwxr-xr-x 2 root root 4096 Aug 17 16:14 development drwxr-xr-x 4 root root 4096 Aug 18 04:29 production Also, the index.php file which is supposed to display when accessing through port 8888, located in /development/: -rwxr-xr-x 1 root root 41 Aug 17 16:14 index.html I have looked at my error_log and found many of the following entries, only being added to the log file when accessing through port 8888. [Sat Aug 18 04:35:09 2012] [error] [client 27.32.156.232] Symbolic link not allowed or link target not accessible: /home/user/public_html /home/user/public_html is a symbolic link that refers to /home/user/domains/mydomain/public_html. The symbolic link has the following permissions: lrwxrwxrwx 1 admin admin 29 Aug 17 15:56 public_html -> ./domains/mydomain/public_html I'm at a loss. It seems that everything is readable or executable. I've set the Directory to FollowSymLinks in the httpd.conf file, but that doesn't seem to make a difference. If I change that directory tag to <Directory "/home/admin/public_html"> (so it has FollowSymLinks on that as well) it still does not work. Any help is greatly appreciated. If I need to post more information, let me know. I'm pretty much a beginner at this stuff. .. .. UPDATE: I ended up changing the configuration to directly go to the actual path of the files, avoiding the public_html symlink altogether. That worked. Thanks for the suggestions folks. DocumentRoot /home/user/domains/mydomain/public_html/development instead of DocumentRoot /home/user/public_html/development

  Read the article

• L-Soft LISTSERV TCPGUI Interface for PHP Creation

  - by poolnoodl

  I'm trying to use LISTSERV's "API" in PHP. L-Soft calls this TCPGUI, and essentially, you can request data like over Telnet. To do this, I'm using PHP's TCP socket functions. I've seen this done in other languages but can't quite convert it to PHP. I can connect, I can change set ASCII or BINARY mode. But I can never quite craft the header packet the way I need to authenticate, so I'm thinking I'm messing up my conversion. C: http://www.lsoft.com/manuals/16.0/htmlhelp/advanced%20topics/TCPGUI.html#2334328 $origin = '[email protected]'; $pwd = 'password'; $host = "example.com"; $port = 2306; $email = "[email protected]"; $list = "mailinglist"; $command = "Query $list FOR $email"; $fp = stream_socket_client("tcp://$host:$port", $errno, $errstr, 30); $cmd = $command . " PW=" . $pwd; $len = strlen($cmd); $orglen = strlen($origin); $n = $len + $orglen + 1; $headerPacket[0] = "1"; $headerPacket[1] = "B"; $headerPacket[2] = "\r"; $headerPacket[3] = "\n"; $headerPacket[4] = ord($n / 256); $headerPacket[5] = ord($n + 255); $headerPacket[6] = ord($orglen); for ($i = 0; $i < $orglen; $i++) { $headerPacket[$i + 7] = ord($origin[$i]); } for ($i = 0; $i < $len; $i++) { $cmdPacket[$i] = ord($cmd[$i]); } fwrite($fp, implode($headerPacket)); while (!feof($fp)) { echo fgets($fp, 1024); } Any thoughts on where I'm going wrong? I'd much appreciate it if anyone could point me toward some code to do this, days of googling and searching here on SO has only lead me to examples in other languages. Of course, if you know C (or Java or Perl as linked below in my comment to bypass the spam filter), PHP, and socket programming fairly well, you could probably rewrite the whole of the code in an hour, maybe a few minutes. You'd have my eternal thanks for that.

  Read the article

• Nginx fastcgi problems with django (double slashes in url?)

  - by wizard

  I'm deploying my first django app. I'm familiar with nginx and fastcgi from deploying php-fpm. I can't get python to recognize the urls. I'm also at a loss on how to debug this further. I'd welcome solutions to this problem and tips on debugging fastcgi problems. Currently I get a 404 page regardless of the url and for some reason a double slash For http://www.site.com/admin/ Page not found (404) Request Method: GET Request URL: http://www.site.com/admin// My urls.py from the debug output - which work in the dev server. Using the URLconf defined in ahrlty.urls, Django tried these URL patterns, in this order: ^listings/ ^admin/ ^accounts/login/$ ^accounts/logout/$ my nginx config server { listen 80; server_name beta.ahrlty.com; access_log /home/ahrlty/ahrlty/logs/access.log; error_log /home/ahrlty/ahrlty/logs/error.log; location /static/ { alias /home/ahrlty/ahrlty/ahrlty/static/; break; } location /media/ { alias /usr/lib/python2.6/dist-packages/django/contrib/admin/media/; break; } location / { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:8001; break; } } and my fastcgi_params fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param PATH_INFO $fastcgi_script_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; And lastly I'm running fastcgi from the commandline with django's manage.py. python manage.py runfcgi method=threaded host=127.0.0.1 port=8080 pidfile=mysite.pid minspare=4 maxspare=30 daemonize=false I'm having a hard time debugging this one. Does anything jump out at anybody? Notes nginx version: nginx/0.7.62 Django svn trunk rev 13013

  Read the article

• Can I use one virtualbox disk for multiple machines?

  - by mxp

  I'm not sure what search term to use and skimming through the VirtualBox manual didn't help me either, so I ask my two questions here... My setup is this: PC with dual boot into Windows 7 and a Debian operating system (both 64bit). I've created a virtual machine (Kubuntu, 64bit) under Windows and put it's VDI file on a SMB share of my NAS. Then I created a VM under linux using the same settings for memory etc and assigned the existing VDI file to it. My idea was that I could use that virtual machine from Windows and Linux as well. (1) Is this generally something that should work without problems? I noticed that snapshots get me into trouble because they appear to be not visible from the other operating system: The snapshots I took after installing the guest system are not visible under Linux. That's why I shut down the VM after usage and not save its state while it's running. My current problem is this: I have used the VM under Windows first, then under Linux. Now it will only start on Linux. When trying this on Windows the guest OS detects some kind of hard disk error and fails to boot because it cannot mount its drive. Obviously the virtual hard disk won't fail so it must have something to do with me using it under Linux. (2) How can I fix that? Update: It also looks like any changes I made in the VM under Linux have been reset by trying to boot it under Windows. Looks like it's back to the latest snapshot. I'm confused... Update The answer to my first question can be found below. In short: It works, as long as you don't use snapshots. The answer to my second question is this: Under Windows set the VM back to the latest snapshot and then discard the snapshot so it gets merged. There should be no snapshots left at the end. If you have multiple snapshots, discard the earliest ones first (Snapshot 1, then 2, 3, ...). I'm not sure what happens if you start at the end (.., 3, 2, 1). This of course leads to some data loss since you revert all changes since the last snapshot. But at least the VM is usable again.

  Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >