Search Results

Search found 4376 results on 176 pages for 'drivers'.

Page 118/176 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Computer bluescreen-ing with 0x7A and 0xF4 errors

  - by lcarpenter

  Hiya, This computer is locking up for around 5-30 seconds before throwing Blue Screen of Death's with 0x7A and occasionally 0xF4 errors. The log files don't really show anything informative, and Windows Update doesn't show any new drivers for the HDD. Upon restart, it shows a "A disk error has occurred /n Press Ctrl+Alt+Del to continue", and to fix this I go into WinRE via the pendrive and run "bootsect /nt60 C: /force /mbr" and that seems to fix it so it boots. And then the cycle repeats. If you want any more information please ask. Thanks, Luke Carpenter

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• connecting to bsnl wll, with huawei fixed wireless modem with connected to usb port on linux mint.

  - by Rakesh

  On windows, when I plugged in the usb connector, to the device was recognized as a mass storage device and installed all the drivers, to my computer, then the device, automatically restarted and started behaving like a modem, I'm writing this post, using the same modem, through windows... On linux mint (debian kernel, similar to ubuntu 8.10), the device is recognized as a mass storage device, some times, but, has no programs, useful for linux... When I use the modem on windows and restart the computer and login to linux, the device shows up as "not yet configured" in the terminal command "lsusb"... I googled a lot for solutions, tried many things, atlast, configured it and run the command "wvdial". But, get the error, that the modem is not responding, at last ! :'( Please help me out... Many more people are facing this problem, as I could discover, when I googled for it. this is the website address of huawei, the company of my modem... "www.huawei.com" Specification: model: ETS1220 FEQ: 800M Thank you.

  Read the article

• Triple ghost animated cursor

  - by R G A

  Since installing the driver for Intuos 4 Graphics tablet, animated cursors display as a triple ghost cursor. I cannot find any reference to this problem elsewhere. System specifications: new Dell XPS, Windows 7, ATI Mobility Radeon HD 4670. Graphics tablet and graphics software are virtually useless since the cursor hotspot is nearly impossible to identify. All drivers and software are current. Any thoughts? Vendors deny any knowledge or responsibility. Removing the Intuos driver does not fix this.

  Read the article

• windows 7 issues with local domain name

  - by Phill

  Until recently my operating system was XP where for the purpose of development and testing of php and zen cart I set up xampp that included apache http server and mercury mail server I also made changes to C:\Windows\System32\drivers\etc\hosts as follows: 127.0.0.1 www.zen.com # For browser access 127.0.0.1 mail.mercury.com # For email access 127.0.0.1 mercury.com # For mercury mail server This allowed the use of www.zen.com in the address bar of my browser rather than 'localhost' and mail.mercury.com to access email via thunderbird. All was well. Then I installed windows7, I made all the mods and again everything appeared to run as expected.Then I turned off my wireless modem causing all working local connections to fail. Localhost in the address bar still works but not www.zen.com and thunderbird 'cannot find mail.mercury.com' Is there some way to overcome what ever is causing this.

  Read the article

• Torrentflux broke after upgrade

  - by parker.sikand

  A working torrentflux setup seems to have gone broken after upgrading PHP to 5.3 and Postrgres to 9.2beta3 on a FreeBSD 8.2 server. The login screen will show up fine, but after clicking the login button, I get an error : Fatal error: Call to undefined function pg_escape_string() in \ /usr/home/parker/tf/html/inc/lib/adodb/drivers/adodb-postgres64.inc.php \ on line 241 Seems to be an error with PHP and the pgsql php package. The phppgsql package itself is not totally broken because I'm using it to host database driven apps on this server. This is the first and only error I'm seeing from it. How might I go about fixing this problem?

  Read the article

• Windows 8 can't open any modern UI app

  - by Joyal

  I just upgraded my machine with Windows 7 Pro x64, to Windows 8 Pro x64, with the Windows 8 Upgrade Assistant. Everything went great, but none of the Modern UI Apps open, and they do not show any error messages or warnings, they just close right away I opened them. I tried to open Skydrive, Windows Store, Photo App,Music App, Bing, Videos , Finances and all the available Modern UI apps on my screen My screen resolution is 1080p, so it is not a resolution issue, I'm using a Windows account , but i switched to Local account but didn't solved the issue. I ran Windows Update and updated my nVidia video drivers. I also tried an app called "Metro App Troubleshooter" without luck

  Read the article

• Looking for a software to keep track of backup media

  - by Tarnschaf

  Hi, I am looking for a software that allows me to enter my used backup media (e.g. DVD1, DVD2) my backed-up assets in high-level (such as "family-photos from 2003", "laptop drivers") details of the assets ("Ninas Birthday 2003") where the backup media is currently stored when the media has been burned (to re-burn in case of media degeneration) Of course it should be possible to navigate from media to assets and backwards. I also thought about marking assets as "deprecated". If all assets on a media are deprecated, the program should tell me so I don't have to keep it any more. Does anybody know a program with this feature-set or will I have to start my own in say Access?

  Read the article

• Is proprietary vendor software required to use a wireless printer?

  - by sajee

  On Windows Vista, other than the driver, one can use a regular printer w/o any extra software, either plugged in via USB or over the network. I don't have to install extra software from the printer vendor to use the basic printer functionality. Is the same true for wireless printers? I need to install the HP 6000 wireless printer, and I hate installing vendor software other than the required drivers. So I'm wondering whether I need to install HP software on every PC that wants to use this printer? I haven't had a chance to read the manual but I'm hoping I don't have to. Can folks that have experience with wireless printers comment on whether vendor software, other than the printer driver, is required to use a wireless printer?

  Read the article

• DVD Drive can read a DVD title and file contents (very slowly) but not play DVDs

  - by Daisetsu

  I've been able to watch DVDs in the past on this computer when it was running XP. I recently upgraded to windows 7 and haven't watched a DVD since then. I put a DVD in and it took quite a long time but windows finally found the disk title, and I was able to explore directories (saw folder like VIDEO_TS). The problem is when I try to have video players play the DVD I just get an error in VLC. It wouldn't tell me the exact error (said to check the log and I don't know where that is). Do I have to install some special drivers/certs in windows 7 to play video?

  Read the article

• Windows 7 Stopped Using hosts file for DNS Resolution

  - by AJ

  I am running Windows 7 Home Premium 64-bit. Starting today, I noticed that DNS resolution is not reading my %SYSTEMROOT%\System32\drivers\etc\hosts file. I say this because I added two new entries to the file and when I run 'nslookup' on the command line, they don't resolve. Further, just trying to resolve 'localhost' results in my primary DNS server being queried. I've read several threads that suggest that the file might have been corrupted and to move it aside and create a new one. I've done that, and no improvement. Is there some sort of registry key that controls the sequence of resources used for DNS resolution (similar to nsswitch.conf on UNIX)? What else could be causing this? Thanks in advance.

  Read the article

• My Logitech G35 headphones aren't very loud on Linux (fedora 14) why?

  - by DarkMantis

  I have recently purchased a set of G35 headphones. They seem to be very loud when I use them on Windows, but when I try and use them on Fedora 14, they are very quiet and I can't seem to make them louder. I have obviously checked the sound settings in Gnome, and they are all up full. I have got ALSA-mixer installed but seems to make no difference. There doesn't seem to be any specific drivers for these headphones for Linux. Anyone know how to make them go a bit louder?

  Read the article

• dell u2410 3dMark Benchmark distortion problems

  - by Scanningcrew

  Ive been doing burn in testing for a new system I have put together and I am running into some video distortion problems with running the 3DMark benchmark tools (Both 06 and Vantage). The graphics will be fine, then sometimes during a test switch the screen will light up with thin horizontal ranibow lines (Something that looks very "glitchy") If i turn the monitor off and back on it clears up. All the tests "pass" and my system gets good marks but it concerns me if I might have problems with games (The screen returns to normal if I dont resest monitor and just let tests pass). I want to return a problem component now before its too late if it is something with the new hardware. Also, I am monitoring temp with thermal laser gun and the card itself is not going above 65c. Any ideas? System: Asrock x58 Xtreme - Last BIOS (1.80) EVGA Geforce GTX 285 w/ latest nvidia drivers (Connect via DVI1) Dell U2410(Set to 59hz refresh 1900x1202 -although I believe benchmarks run 1200x1024) Windows 7 Ultimate 64 12Gb DDR3 1600 RAM

  Read the article

• add printer on windows 7 with vbscript and wmi

  - by Jessica

  I have a problem where I can't add a printer on my Windows 7 machine, because it fails with "The printer driver is unknown" (error code 1797) using WMI/VBScript. The thing is that the printer driver already exists on the PC. I've used AddPrinterConnection to connect to the remote printer queue, and the drivers get installed. I've confirmed they exist by a) Enumerating Win32_PrinterDriver with WBEMTEST utility which shows the driver, and also in the Printer Management MMC snap-in. Is there some other scriptable way I can get this to work? I'm adding a local TCP/IP port, pointing my new printer object instance to use that port and the driver from using AddPrinterConnection, and giving it a name, but it refuses to work...

  Read the article

• bad printer isolation on print server or better way?

  - by Joseph

  I have noticed that when a printer or driver screws up on a Windows server it usually locks up or kills the print spooler and everyone can't print until it is fixed. Usually we have to put the troublesome printer on another server so when it fails, it doesn't take the whole group with it. That is assuming we ever figure out which printer is the problem. Is there a way to have it so that one bad apple doesn't ruin the bunch? Even if it is another form of printer serving, that would work as long as it's not hard for the user to find a printer and install drivers.

  Read the article

• Third party biometric software.

  - by Iszi

  Most of us with fingerprint readers and such devices probably use the software provided by the vendor, to enable biometric OS login or single sign-on functionality. However, I've recently wondered if there is any third-party software that will do the same thing? This would be similar to how you don't need the manufacturer's software to use a scanner, printer, or webcam - you just use their drivers and your choice of software. Is there anything like this for fingerprint readers or other biometric devices? Free or Open Source projects are preferred, but I'd be interested in learning about any existing solutions regardless. I personally am particularly interested in Windows-compatible software, but I'll leave the query open for any OS.

  Read the article

• Recover data from hard disk

  - by Hitesh Solanki

  Hi I have formatted my c: drive and window xp is installed successfully,but I cannot able to access d: drive. when I am trying to double click on the d: drive,following message is displayed: "the disk in drive D: is not formatted, do you want to format it now ? " When I am trying to access from command prompt,the following message is displayed: "The volume does not contain a recognized file system. Please make sure that all required file system drivers are loaded and that the volume is not corrupted." So please help me.... Thanks in advance....

  Read the article

• Old PCI Video Card and PCI-Express ATI Radeon HD 4200 Pro Living Together

  - by Adam Driscoll

  I have two video cards installed in a Dell Optiplex 745. The PCI card is from 2001 and I was hoping to be able to install it, allowing me to have 3 monitors. The Radeon is already running two itself. The problem is that when I boot the box with default BIOS settings the PCI card displays video to the single display but not the other two. In device manager I can see that both video cards are visible with drivers loaded correctly but underneath monitors I only have a single Generic PnP monitor from the VGA connection to the PCI card. If I switch the BIOS setting to force PCI-E I get the Radeon to display to the two other monitors. When I check device manager with this configuration I see that the PCI card displays an error saying the driver could not be started. Any ideas?

  Read the article

• How to diagnose repeated freezing of windows 7 (comes back alive in few seconds)

  - by Akash Kava

  I installed Windows 7 in a 3 year old machine, it installed successfully, took all drivers and running great, but what happens is every 5-6 minutes it freezes for few seconds... 30 seconds to 1 minute and then comes back alive. I checked Event Viewer, nothing matching the frozen timeline. I would appriciate any help on how to detect causing service/hardware. After it comes alive, everything runs normal, I did run task manager and checked cpu usage, at time it freezes just before and after that no task took more cpu or memory, it was like idle machine. No external usb drives or no devices, on board intel desktop board with SATA HDD, SATA hdd running in absolute good mode.

  Read the article

• Vista: Improving troubleshoot approach skills

  - by Chau

  I'm not a Windows SuperUser, but neither just the regular user. I don't mind browsing the Registry, using Process Explorer, reading the Event logs, (un)installing new drivers and so on, but all this only makes me solve some problems. I tend though to run into problems where these tools aren't enough. Which tools should I learn about to improve my troubleshooting skills in Windows? Currently I'm using Windows Vista x64 (not moved to 7 yet), facing audio/video stuttering problems and I think this is a good place to improve my troubleshooting skills. I know this post is similar to this question, but my machine is only hanging occationally. Specs: Intel Q6600 Stock speed ASUS P5QD Turbo 4GB ram NVIDIA GTS-8800 640 HDA Xplosion 7.1 Seasonic 430W Windows Vista Business x64

  Read the article

• HP LasterJet P2035 not mapping on remote desktop

  - by Matthew Pomar

  I am connecting from a Windows 7 Pro laptop to a remote 64bit Windows 2008 R2 server via Remote Desktop. My local laptop has a networked HP LaserJet P2035 printer set as the default printer. When I connect to the server, the local (networked) HP printer does not get mapped on the server. I've installed the 64bit drivers from HP for the printer and was able to create a test printer on the server itself using the correct driver (HP LaserJet P2035) priting to a file. I've also checked the Printer under Local Resources tab on my Remote Desktop client. Does anyone know where else I should check to get my local printer to make to my remote desktop session?

  Read the article

• Jerky animation on window open/close

  - by Jan Zich

  Today, I received and installed Windows 7, and one of the first (slightly) annoying things I noticed is a visible jerk when opening of closing new windows. When I minimize or maximize already running window, the animation is smooth from beginning to end, but when I start a new program, it seems that just at the end of the animation Windows thinks for a fraction of a second. It is a bit distracting; especially since Windows 7 seems to be overall more responsive than Windows Vista. Does anybody has the same experience? Could it, for instance, a 64bit version specific issue (just in case)? I upgraded Vidia drivers, and even though my video card is not capable running latest games, it should be able to handle this (since it was OK in Vista, and since it does not look like a video issue).

  Read the article

• Customized windows xp installation

  - by user23950

  How to create a customized version of an xp installation cd. I want a hand's off installation that will install all the themes, drivers , and applications I need without my intervention. How can I do that. I tried to make use of this software called Nlite. But when I tested the iso file using virtual box. The virtual box said that there's a certain file that cannot be copied. And by the way, before I customized the original iso image of windows xp sp3, it doesn't have the file copying problem that I mentioned above.

  Read the article

• Visio 2010 Reverse Engineer Oracle

  - by digitall

  I have used Visio 2007 in the past to reverse engineer Oracle databases to get a flow scheme. I believe all Office 2007 products were x86 as well which is where I suspect my issue currently lies. I have since upgraded to Visio 2010 x64 and when I go to reverse engineer something from Oracle it shows up under Installed Visio Drivers but I can't seem to create a data source using it. My assumption here is it is because Oracle doesn't play nicely with x64 and with Visio being compiled as x64 I don't even get the option to use it. Has anyone done this with Visio 2010 x64 and Oracle yet? Or are there other tools you would recommend to reverse engineer and get a model such as the one generated by Visio?

  Read the article

• Scan And Fix a RAW drive

  - by Claus Jørgensen

  Hi Basically I got the same problem as described in this thread. When I plug my HTC Hero Android Phone with USB into my Windows 7 computer I get a "Do you want to Scan and Fix" message. However, if I click "Scan and Fix", the USB instantly unplug itself, so that's no good. I've tried updating drivers from HTC with no luck. I've also tried running chkdisk from command-line with the message that it can't be used in RAW drives. This is really really annoying, and the SD card works just fine if I ignore the message, so I just want a way to disable/hide this message permanently. If anyone have some ideas how this can be done, please let me know. Thanks.

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >