Search Results

Search found 503 results on 21 pages for 'cables'.

Page 12/21 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• Cannot use second display with 12.04 and Intel 2000/3000

  - by Carolyn Marenger

  I am unable to get anything to display on my second monitor, or even get the system to recognize that there is a second screen. I am running Ubuntu 12.04 on a Gigabyte GA-H61M-S2PV, revision 2.0 box. The integrated chipset is an Intel 2000/3000, and there are both a D-Dub and a DVI-D display ports on the MB. This is the first operating system I have installed on this system. I have a second monitor plugged into the DVI-D port via a DVI-D to D-Sub adapter. I cannot verify that the motherboard or adapter were/are working, short of installing windows to test the theory. When I go into the "System Settings - Displays" control window, it shows one display. I have rebooted with the second monitor attached, and I have perused the BIOS settings in case it might have been disabled. So far, I have had no indication that the second monitor is recognized, not even a flicker at power on. If I swap monitors and cables between the DVI-D and D-Dub ports, the other monitor lights up, so I know the monitor and video cable are not the issue. Any suggestions would be appreciated. Thanks, Carolyn

  Read the article

• PC is randomly shutting off

  - by Bobby

  I have a PC which is randomly shutting off (the hard way, like someone pulled the plug). It's no heat problem, because this can happen after 2 minutes of operation or after 4 hours and I checked the temperature. It's also no problem of the operation system, because it will also do that while in BIOS. If it happens once, you can be sure that it will happen within the next hour another two or three times, and then it works again for over a week or even longer. Possible causes I've thought about so far are: Voltage Fluctuation Loose contact (already replugged all cables within the PC, no luck) Faulty PSU Maybe someone has more ideas to this? P.s.: I don't have the hardware specs with me right now, I'll post them as soon as I get them.

  Read the article

• Wrong screen resolution with HDMI output to HDTV

  - by bruno077

  I own an HDTV with a native resolution of 1360x768. Sometimes I plug in my laptop to watch movies, and I used to do it with a VGA cable. I've had no problem setting the laptop to the TV native resolution with the VGA cable (1360x768). Having acquired an HDMI cable recently, I can't go past 1280x720, and if I do, the TV displays "invalid format". At 1280x720, the image is viewable but not centered, so for example I can't see the windows taskbar or titlebars. I've tried both cables (VGA and HDMI) with the same settings: Laptop's display turned off and trying to set the Tv's native resolution. What could I try to fix this issue? Could it be a faulty cable? (I'm using a Thinkpad with Windows 7) EDIT: My graphics adapter appears listed as Mobile Intel(R) 4 Series Express Chipset Family (Searching for my laptop's model yields Intel GMA 4500MHD as the graphic card) I'm downloading a driver update from Intel's website. I'll report my progress when I check its behavior tomorrow.

  Read the article

• Why are applications slowing down on the computer's second monitor?

  - by ChristianLinnell

  Here's an interesting one. Problem I have a user on Windows XP who is running a web application inside IE8. She has two monitors plugged in via DVI cables. When she is working the the browser on her primary monitor, everything is fine, but when she drags the window over to the second monitor, the web applications functionality grinds to a halt. It's not just web apps either - many applications exhibit the problem. What I've tried Switching the two monitors in the OS. It's obviously not the monitor's fault. Confirmed that it's the app slowing down, and not the graphical rendering. The application in question actually locks up. The mouse is unaffected, and I can drag other windows on top of the problematic application. Any ideas?

  Read the article

• How to programmatically control slave computer on BIOS level?

  - by PovilasSid

  I want to run some test on hardware level. My goal is to create or find a way to control one computer from another down to BIOS settings changing. For example: Master computer sends a signal for slave to restart and opens BIOS settings dialog. Master computer sends a signal to slave to change BIOS parameters and then restart. Then slave fully boots up master starts up some software on slave. Then software finishes operations cycle continues till certain conditions are met. I know that I am looking for a complex thing but mainly what I need are correct keywords because now I am being flooded by BIOS configurations tutorials. Main concerns: Is it possible without using any custom tailer chip? How can master monitor salve`s hardware activity? How to let master handled more than one slave? How what connections are needed to create this kind of setup? (cables)

  Read the article

• Has anyone had luck getting an external hard drive working with a PCMCIA USB card?

  - by Carl

  I would like to know if anyone has had any success in getting and external 2.5" IDE hard drive in an external case (w/USB cable) working when plugged into a PCMCIA USB card. My hard drive doesn't work when plugged into my HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My MP3 player will work fine when plugged into it. I tried plugging in both of the USB cables that are one one end (Y cable), and it doesn't make a difference. I read the problem may be insufficient power.

  Read the article

• print job doesn't go to print queue

  - by flatsguide

  I have two printers hooked up to my intel imac. I am having a printing error. It seems that whenever i try to print (a simple text doc) I am unable to get the print job to go to print queue with one of my printers. I have a HP c7280 and a HP c3100. I am able to get one working properly, but the other doesn't seem to allow it to go to the print queue. I have switched usb cables (with the printer that I know works) and both printers are recognized by the computer in the printer preferences pane. I've tried reseting the printer system in the printer setup utility.. reloaded the drivers from HP.. etc. If anyone has a suggestion or could point me to a little help i'd be VERY grateful Best Regards.. B

  Read the article

• Do most front and rear USB connections deliver the same power and performance?

  - by Bratch

  I was reading this Three Monitors For Every User and there were some comments about rear USB ports being able to deliver more power than front USB ports because they are directly connected to the motherboard and closer to the power supply (by circuit board runs). Even though the front USB ports may have connectors farther from the power supply, and there are cables from the motherboard to the front ports, I think that the difference in power would be negligible (unless the case is over 5 meters long). Anyone know for sure if they are the same or different? Note that I'm not talking about an older case where the front might have been USB 1.1 and the rear USB 2.0. A modern case would have USB 2.0 on all ports. And of course using a powered hub would deliver plenty of power.

  Read the article

• DVI to VGA adapter only working in one output

  - by Tom Jenkinson

  I have a AMD Radeon HD 6800 Series graphics card which has 2 DVI outputs. I tried to set it up with 2 monitors which both have vga connectors on the end and used 2 dvi to vga adapters like these. http://www.tvcables.co.uk/images/items/vga-to-dvi.jpg For some reason nothing would reach the monitor, it would remain in standby, if it was plugged into the second output. I tried all the different combinations of cables, adapters and the 2 monitors but whichever monitor that was plugged into the second output wouldn't work. I then randomly decided to plug a different monitor into the second output which has a dvi connector on the end so there was no need for an adapter and plugged it in and it worked! Does anyone know why the second output on the graphics card won't work with a dvi to vga adapter (and the first output will)? I'm really confused! Thanks

  Read the article

• Trying to turn an WD Mybook 1TB to slave drive in PC

  - by Steph W

  Yes I realise that most external Hard Drives would not be transitioned into internal sitting Hard Drives, but unfortunately we broke the miniUSB connection that transfers the data from external Hard Drive to laptop. What we are TRYING to do now, is get the WD MyBook 1TB to funtion alongside (preferably as SLAVE) to my currently exsisting Desktop Hard Drive. both are SATA drives. We have the SATA power, and Data cables, and these are in place (but - somehow NOT working) - Help please - I am not computer illeterate, just don't know how to switch this so it works. How do I turn one into master, and the newer one (that was external) into the slave drive?

  Read the article

• Cable installed - now my hub has no connection the router/modem - what do I need to buy?

  - by bcmcfc

  My previous setup was as follows: [modem/router]------[switch]+------ [pc1] +------ [pc2] I've just moved and had cable installed and I no longer have the option of running a lengthy LAN cable from the router to the switch to provide network and internet access to the two PCs. The cable company provided 2 wireless N USB adapters. What do I need to buy to plug into where in order to restore the network to its previous state? PC1 dual boots Windows 7 and Ubuntu 12. PC2 runs Debian 6. Edit: USB adapters - Netgear WNDA3200 Switch - TP-Link TL-SF1008D 8 port Ethernet switch Cabling - various patch cables cat5e rj45 Modem/Router - pretty standard cable company job - wireless Intention is something like- [modem/router] --wifi-- [some-new-hardware or perhaps to pc1] ----[switch]---[pc1/2]

  Read the article

• Transferring analog media (VHS casettes, vinyl records) to PC

  - by Javier Badia

  I have some VHSs and vinyl records which I'd like to convert to DVDs and CDs, respectively. I have a couple of questions about how to hook the devices up to the computer. I've seen some RCA-to-USB cables on the Internet like this one. Will those work for connecting the VCR to the computer? And what program would I use to take that and save it as a video file? Can I connect the phonograph directly to the Line In port in my PC or do I need some amplifier or something in the middle? I'm using Windows 7 x64, if it matters.

  Read the article

• How to troubleshoot latency between 2 linux hosts

  - by Jimm

  The latency between 2 linux hosts is about .23ms. They are connected by one switch. Ping & Wireshark confirm the latency number. But, i dont have any visibility into what is causing this latency. How can i know if the latency is due to NIC on host A or B or the switch or the cables? UPDATE: The .23 ms latency is bad for my existing application, which sends messages at very high frequency and i am trying to see if it can be brought down to .1ms

  Read the article

• How to get external 2.5 inch HD enclosure get recognised

  - by fireBand

  I am completely out of ideas. I have 2.5inch HDD from my old laptop, I have tried with 2 different HDD enclosures but my desktop does not recognize it. Not even showing in the disk management or BIOS. The HDD works fine if I use in a 3.5 inch enclosure with external power. I have tried 3 different Y USB cables. I have also got a 7 port self powered 2A USB hub. I have updated my chipset drivers as well. The problem is with my desktop , the enclosures work fine with my new laptop. Anything else that I should try? Thanks in advance.

  Read the article

• print job doesn't go to print queue

  - by flatsguide

  I have two printers hooked up to my intel imac. I am having a printing error. It seems that whenever i try to print (a simple text doc) I am unable to get the print job to go to print queue with one of my printers. I have a HP c7280 and a HP c3100. I am able to get one working properly, but the other doesn't seem to allow it to go to the print queue. I have switched usb cables (with the printer that I know works) and both printers are recognized by the computer in the printer preferences pane. I've tried reseting the printer system in the printer setup utility.. reloaded the drivers from HP.. etc. If anyone has a suggestion or could point me to a little help i'd be VERY grateful Best Regards.. B

  Read the article

• Lost Page Write I/O Errors on CentOS LVM setup

  - by Gregg Leventhal

  I have a CentOS 6 box with LVM setup and one of the PVs is a USB disk (I know). One of them is getting the error: Oct 30 10:57:07 alpha01 kernel: lost page write due to I/O error on dm-3 Oct 30 10:57:07 alpha01 kernel: Buffer I/O error on device dm-3, logical block 4 Which is causing problems with all of the LVs on it. pvs shows the PV as unknown device. I can ls to the logical volumes and they show up in lvdisplay, but first I get a bunch of IO errors. I made sure the cables are secure between the USB drive. What should I do to get this back up and running for the meanwhile? Should I unmount each LV and run an fsck.ext4 on each one like fsck.ext4 -y /dev/vg1/lv_logvolname ?

  Read the article

• "Input not Supported" on external monitor

  - by Shalan

  when it rains, it pours! Im helping a friend with his Dell Inspiron 1520. The hdd crashed and and top of that, the screen is cracked. I've replaced the hdd (SATA-5400), but the lcd replacement is only comin in a months time. I've tried to: hook the laptop up to an Acer 18.5" lcd monitor via VGA, boot up into Windows 7 installer, get to the Step-1 screen, Switch to external display (Function-F8) ...and get the "Input not supported" message on the Acer lcd. I know that this is a resolution problem, but cant for the life of me figure out how to solve this. I've also tried, hooking it up to my TV via Composite cables (got a VGA-Composite adaptor). Please could someone advise me what to do? -Thank u!

  Read the article

• Cascading KVM switches

  - by einpoklum

  I have a not-so-small number of computers (say, 5) which I want to access with a single keyboard, USB and monitor. I can get an 8-port KVM switch, which is a pretty expensive piece of hardware; however, in theory, I should be able to cascade KVM switches: Have one 4-port KVM switch between 2 other KVMs (a 2-port and a 4-port). Is this doable (with typical off-the-shelf switches and cables)? Has anyone had experience doing this? Note: I'm interested in USB-only for the keyboard and mouse, and either VGA or DVI for the display. Audio and PS/2 connections are irrelevant for me..

  Read the article

• How to test Laptop NIC's throughput using a router and PC - without be bounded?

  - by 0x90

  My setup includes: Cisco router An i-7 PC running windows A laptop with high speed wifi nic, which I want to check its throughput. I would like to run an FTP server on the PC. hook the router over cables to the PC. I would like to have the PC create its own subnet accessible via the cisco router that would be hooked directly to the PC's nic. From the laptop I want to connect via wifi to the PC's wireless router and connect to the ftp server on the PC. is it possible? how do i connect the router to the PC nic and make it broadcast a subnet via wifi for my laptop to connect to? how do i configure an FTP server to operate only on this subnet?

  Read the article

• Wired card not connecting after trying to connect

  - by Mike

  I have an Ubuntu 12.10 PC. When I plug in my internet cable it starts connecting and after a minute it says it can't connect. I tried different cables but nothing works. Wlan works. I think it's the network driver but I don't know how to install/update it. Here's the ifconfig info (if it helps): eth0 Link encap:Ethernet HWaddr 00:01:6c:39:2a:8d inet6 addr: fe80::201:6cff:fe39:2a8d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2011 errors:0 dropped:362 overruns:0 frame:0 TX packets:586 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:175452 (175.4 KB) TX bytes:147211 (147.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9779 errors:0 dropped:0 overruns:0 frame:0 TX packets:9779 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8460080 (8.4 MB) TX bytes:8460080 (8.4 MB) wlan0 Link encap:Ethernet HWaddr 08:10:74:35:99:9d inet6 addr: fe80::a10:74ff:fe35:999d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1790 errors:0 dropped:0 overruns:0 frame:0 TX packets:3250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:401664 (401.6 KB) TX bytes:2898773 (2.8 MB)

  Read the article

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Autoplay for USB drive keeps popping up

  - by Adam Haile

  I have a Seagate external 2TB USB drive that when I leave it plugged in, the Autoplay dialog asking what to do with the drive pops up about once every 30-60 minutes. No matter how many times I tell it to go away, it keeps coming back. I have tried multiple power supplies, USB cables, and all the USB ports on my machine...but it keeps doing the same thing. Also, this does not happen with the same drive on a different computer. Could this be some power or configuration setting that is causing this? I'm running Windows 7 x64 (the computer it works on is x86)

  Read the article

• Frequent connection drops when playing online games (StarCraft 2, Battlefield 3) and behind NAT - how to diagnose? [migrated]

  - by Moshev

  I am having some trouble with (I suspect) my wireless router. It's connected to the internet with a regular lan cable and has a static, public IP address. Our two home PCs connect to the router with regular lan cables, plus there's a laptop which connects over wifi. diagram: Internet | | <- isp-supplied cat5 ethernet cable | D-Link D300 ...wifi... laptop / \ / <- cable -> \ PC1 PC2 The PCs and laptop are behind NAT and share the router's public IP. The router is a D-Link D300. PC1 is used for online gaming and I'm experiencing frequent "connection dropped" errors when playing Battlefield 3, StarCraft 2 and the Diablo 3 beta; but not with TeamFortress 2 or the Tribes Ascend beta. The issue goes away when I remove the router and connect PC1 directly to the ISP's cable. I have also tried disconnecting PC2 and the laptop, leaving PC1 as the only machine connected to the router - doesn't help. How can I diagnose what precisely the issue is?

  Read the article

• How is fire spread in server rooms and datacenters?

  - by sharptooth

  Every now and then I read that a severe fire has happened in some datacenter, lots of equipment has been damaged and customers have gone offline. Now I wonder what is there to support and spread fire? I mean walls in a server room usually have little or no finish. Racks are made of metal. Almost all units have metal cases. Cables have (or at least should have) insulation of materials that don't spread fire. What is spreading fire in a server room or datacenter?

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >