Search Results

Search found 2344 results on 94 pages for 'ethernet'.

Page 12/94 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• Connect devices plugged into Raspberry Pi ethernet to WiFi network

  - by Tom

  I'm just starting out on a mission to learn more about networking and I've followed a tutorial (http://raspberrypihq.com/how-to-turn-a-raspberry-pi-into-a-wifi-router/) to turn my Raspberry Pi into a wifi router. That worked really well so I modified it slightly so that I can use a tethered iphone for the internet connection - I just switched all "eth0" references to "eth1" (the iphone interface) and added a script to set everything up when the phone is plugged in. This setup has freed up the Pi's ethernet port so I'd like to try and take this a step further and allow devices plugged into it to connect to the network. If possible, I'd like to try adding a switch so I can connect multiple devices. I've tried fiddling around with nat & iptables with no luck so my question is, how can I connect devices on eth0 to my wlan network?

  Read the article

• FreeBSD: Samba performance over GBit-Ethernet

  - by Axel Gneiting

  I'm using a FreeBSD NAS with RAID-Z. I can read ~300MB/s from the ZFS disks to /dev/null on the box, but only get about 50MB/s over GBit-Ethernet with SMB to Windows 7 (Samba 3.5.6). Both systems have Intel-PCIe-NICs and are connected directly. Samba is configured to use AIO and I already tried to tune TCP/IP: kern.ipc.maxsockbuf=16777216 net.inet.tcp.sendspace=1048576 net.inet.tcp.recvspace=1048576 net.inet.tcp.sendbuf_max=8388608 net.inet.tcp.recvbuf_max=8388608 net.inet.tcp.delayed_ack=0 Any ideas what's causing the bottleneck? I think the link should handle 100 MB/s easily.

  Read the article

• Automatically wake up notebooks not on the ethernet

  - by gletscher

  I am looking for an automated backup system and I like bacula. I have 3 Notebooks and a Desktop computer that need regular backup. Now I don't want to let them run all night just to do the backuping, so I was thinking I could use wake-on-lan to have bacula wake up the machines, then do the backups, and shut them down afterswards. While this may work with devices on the ethernet, it won't work with the Notebooks on the wifi. So is it possible to have the Notebooks schedules to automatically wake up from suspend or shutdown ? Or is it possible to interject a shutdown command if it is after a certain hour and call the bacula director to start the backup now? I'm new to controlling the linux system using scripts, so any hints on how and where to start are greatly appreciated. Thanks alot for your help, input and ideas.

  Read the article

• how to run an AFS file server on a specific ethernet card (in Debian)

  - by listboss

  I have a linux box running Debian server with minimal number of packages (so no GUI for network management). The box has two ethernet cards, one of which (eth0) is connected to a Mac OSX computer using a cross-cable. I can bring up eth0 and assign a static ip (10.10.11.16) to it. This way I can ssh to the box through the cross-cable. This is what I run on Linux box: ifconfig eth0 10.10.11.16 netmask 255.255.255.0 up I also installed/started a file server (AFS) on Debian. So far, the file server can only be accessed through eth1 which is exposed to my home LAN and www. My goal is to set up the file server so that it's only visible through eth0. Is this possible? and if yes, how can I do it?

  Read the article

• Connecting office to data center via Metro-ethernet

  - by Eric

  I am installing a metro ethernet link from my office to my data center. The office will have a cisco 3750 with several vlans. The data center end will have a more complicated set up. The metro e from the office will connect to a 2960, which will have two other 2960s with a few vlans and a 2811 router connected to it for connectivity to our other environments and the internet. I am looking at implementing this by connecting the office 3750 and the data center 2960 with a dot1q trunk and doing all routing at the 2811. I will configure subinterfaces for gateways for each of the vlans on the 2811. I work for a small company and don't have much of a budget for an ideal architecture. I can post a simple diagram if needed for clarification. Is there anything I am missing here? I feel like I am forgetting something very basic and want to make sure I eliminate any boneheaded mistakes.

  Read the article

• Ethernet port sleeping on PS3 running linux

  - by Doug

  My lab has a PS3 running Ubuntu Linux 9.04 Server Edition. After a period of a few hours with no use, the Ethernet connection (eth0) seems to go to sleep, causing the connection to be lost. Pinging or trying to SSH into the machine results in no response. The fix I've been using is to access the machine locally and restart it (trying to bring eth0 down then up doesn't seem to correct it). I've tried setting up an hourly cron job that runs on the PS3 and pings another machine just to create network activity, but this doesn't seem to solve the problem either. Update: The solution was to run the above cron job much more frequently: every 10 minutes works.

  Read the article

• Why is my ethernet interface in promiscuous mode

  - by nhed

  I read that seeing a flag of M in netstat -i is the way to tell which of your interfaces is in promiscuous mode I run it and I see that eth1 is in promiscuous mode $ netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth1 1500 0 1770161198 0 0 0 57446481 0 0 0 BMRU lo 16436 0 97501566 0 0 0 97501566 0 0 0 LRU This seems to be the case on all the machines I checked (All Centos6.0, both virtual and physical), any idea why ethernet devices would be in such a mode unless someone was running any pcap based app (sudo lsof | grep pcap shows nothing)? I did not see any mention of promiscuous in any of the config files (sudo grep -r promis /etc) Any ideas what puts the interface into that mode and why? p.s. most of the posts I see seem to be security related, this is not that

  Read the article

• Encryption over gigabit carrier ethernet

  - by Roy

  I would like to encrypt traffic between two data centres. Communication between the sites is provided as a standard provider bridge (s-vlan/802.1ad), so that our local vlan tags (c-vlan/802.1q) are preserved on the trunk. The communication traverse several layer 2 hops in the provider network. Border switches on both sides are Catalyst 3750-X with the MACSec service module, but I assume MACSec is out of the question, as I don't see any way to ensure L2 equality between the switches over a trunk, although it may be possible over a provider bridge. MPLS (using EoMPLS) would certainly allow this option, but is not available in this case. Either way, equipment can always be replaced to accommodate technology and topology choices. How do I go about finding viable technology options that can provide layer 2 point-to-point encryption over ethernet carrier networks?

  Read the article

• bat file to disable ethernet adaptor and then reenable it after windows log in

  - by jaslr

  When I log into Windows 7 I need to wait 10 seconds and then disable the Local Area Connection (ethernet adaptor) and then reenable it. I have looked through the suggested answer: Enable/disable wireless interface in a bat file but that seems irrelevant as it just toggles the current state. From what I can tell I need to include: netsh interface set interface "Local Area Connection" DISABLED netsh interface set interface "Local Area Connection" ENABLED but I'm unsure of the wait time or how I can have this start after Windows has successfully logged in. What's the best approach here?

  Read the article

• Creating a network adapter - how hard is it?

  - by Vilx-

  I'm interested in building a little (commercial) device on top of Arduino. I want it to be able to interface with network. Network as in standard Ethernet, Cat5, RJ-45, etc. I know that there is an Ethernet Shield, but it costs even more than the Arduino itself, and it's pretty big. Naturally, I want my device to be as small and as cheap as possible. So I'm thinking about recreating an Ethernet module myself. The problem is - I haven't got any experience with Ethernet, nor do I have a good idea where to start looking. Thus I can't even say if my ideas are feasible. Ultimately I would like the device to have three ports - one for incoming signal, two for outgoing, so the device is essentially a little switch where it is plugged in itself as well. The switching capabilities need not be very fast - the volume of data will be low. 10Mbit is more than enough, can be even slower. If that is not possible, a single port for controlling the device itself will also do. Another possibility I'm considering is power line communications - sending information through power lines. That's another area I've no experience with. What hardware should I be looking at, and where can I find information about the necessary software? So - can anyone tell me if these ideas are feasible, and if yes - where should I start looking?

  Read the article

• Failover or load balancing configuration on Apple Xserve and Mac OS X Server Snow Leopard (10.6)

  - by Alasdair Allan

  I'm currently installing a number of Apple Xserve boxes running Mac OS X Server (10.6). After poking and prodding for a while I can't find any obvious way, or documentation telling me how, to set up the 2 ethernet ports in a failover or load-balancing configuration. There seems to be an obvious way to do link aggregation, but not failover or load-balancing? What's the default configuration if I enable both ports with the same (manually configured) IP address?

  Read the article

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• Daisy-chaining network switches with multiple cables

  - by user72153

  This might just be the dumbest question you'll ever read, but I digress. Say I have two 100Mbps Ethernet switches with 2 computers on each, connected together by a single cable. This way, the two PCs on each switch share the 100Mbps bandwidth with the others. If I added another cable between the 2 switches, would there be 200Mbps throughput available between the switches? Or am I completely off my rocker? Thanks for the help.

  Read the article

• How do I wire a crossover cable to connect two devices together?

  - by Axxmasterr

  I need to make a ethernet crossover cable to connect two devices together. Anyone know the process to make one from scratch?

  Read the article

• Linksys by Cisco EZXS55W EtherFast 10/100 5-Port Workgroup Switch

  - by studiohack

  I'm looking into buying a switch to expand the one ethernet port on one level. I'm considering "Linksys by Cisco EZXS55W EtherFast 10/100 5-Port Workgroup Switch" from Amazon, but I'm not sure what the 'Etherfast' and the 'Workgroup Switch' parts mean? Will it work like a regular switch, or is it different? Thanks!

  Read the article

• Can I use an Apple AirPort Express as a wireless-to-wired bridge?

  - by Chris

  I have a wireless network using an Apple AirPort Extreme. That device is set up in my office and hooked up to the cable modem. I have a TV in another room which can accept a wired internet connection (not wireless enabled). Can I use an Apple AirPort Express's ethernet jack to create a wireless-to-wired bridge? If not, what device would I use to do the same thing?

  Read the article

• Computer sending data while turned of

  - by Nicklas Ansman

  I have a some what strange problem (which could have and easy and obvious solution for all I know). My problem is that when I've booted ubuntu (now 10.4 but same problem with 9.10) and turns it off it starts sending a HUGE amount of data via the ethernet cable, so much in fact that my router can't handle it and stops responding. As far as I can tell the computer is completely turned off with no fans spinning. I can add that if I boot windows I do not have this problem, just when exiting ubuntu. There are two "fixes" for my problem: Pull the ethernet cable until the next boot Turn off power to the PSU and wait for the capacitors to unload Is there anyone who knows what could be going on? I'd be happy to post some logs or conf-files. Currently I'm using the ethernet port on my motherboard which is a Asus P6T Deluxe V2 with an updated version of the BIOS (maybe not the latest but since it only happens when I've been in ubuntu I don't wanna mess with the BIOS too much). Regards Nicklas

  Read the article

• Cisco sg100-08 connections

  - by Terix

  I have multiple computers, some have a 10/100 ethernet adapter while others have a 10/100/1000 ones. If I connect them together with the Cisco sg100-08 switch, do I keep the 1Gbit speed where possible (between two devices at 1Gbit speed) or the whole lan slows down to 100mbit? I checked Cisco website but I couldn't find this kind of information, nor I was able to register to the Cisco support to ask this question (the registration form does not work)

  Read the article

• How to configure LAN controller to run at 1Gbps connectivity?

  - by Metro Smurf

  I have a few computers connected through a Gigabit router which show 1Gbps connections. However, one of the computers only shows 100Mbps connectivity even though it is capable of 1Gbps. I am not seeing an errors in the event viewer. Computer Specs Windows XP SP3 x86 A8N-SLI Premium MoBo Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller Driver: Marvell v11.24.3.3 (2/15/2010) Networking Specs Netgear RangeMax Premium Wireless-N Gigabit Router (WNR3500) CAT6 wiring Question: How can I configure the above computer to run at 1Gbps connectivity like the others?

  Read the article

• Two network cards latency

  - by Ross W

  I'm trying to setup a network architecture where one network is a low-latency low-bandwidth tcp control system (GBit), the other is a high-bandwidth udp (maybe tcp) network that could get saturated (GBit). If I have two NICs inside a server running Linux. What happens to the low-bandwidth/low-latency network when the high-bandwidth gets saturated. Does each Ethernet card get the same amount of priority inside the kernel or would the low-latency network suffer from the high-bandwidth being saturated?

  Read the article

• printing parallel over ethernet cable

  - by Crudler

  I have a bit of an interesting challenge :) I have a machine with a parallel printer output, i want it to be able to print instead to a printer in a different room and i know that parallel isnt great over big distances. i found this: http://www.amazon.com/over-Cat5-Extension-Cable-Adapter/dp/B002WJ9S6Y%3FSubscriptionId%3DAKIAINHICTCYYZGJWT4Q%26tag%3Dusbprintercables.net-20%26linkCode%3Dxm2%26camp%3D2025%26creative%3D165953%26creativeASIN%3DB002WJ9S6Y which will let me connect over cat5, but its usb to cat 5. my machine can only output on parallel (its not a computer) so what i was thinking of getting is a parallel(f) to usb and usb to parallel (M) for either side i.e. machine - parallel - usb - cat5 - usb - parallel -printer just seems a bit messy :) suggestions? another thing i would like to try is to get rid of the old school parallel printer and instead use a network based multi function. would this be possible? i.e. machine - parallel -usb - cat5 - ethernet print server - network printer this might be rougher because the machine cannot "know" that we are using a network printer. it can ONLY print to LPT1 Thanks!

  Read the article

• Weirdly high ping on direct ethernet connection?

  - by Antriel

  I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

  Read the article

• What is the fall off of subsecond throughput on Ethernet Network Interfaces

  - by Kyle Brandt

  On a network interface, speeds are given in term of data over time, in particular, they are bits per second. However, in the uber-fast world of computing -- a second is kind of a really long time. So for example, given a linear falloff. A 1 GBit per second interface would do 500MBit per half second, 250Mbit per quarter second etc. I imagine at certain units of time, this is no longer linear. Perhaps this is set by ethernet frequencies, system clock speeds, interrupt timers etc. I am sure this varies depending on the system -- but does anyone have more information or whitepapers on this? One of the main reasons I am curious is to understand output drops on interfaces. Even if the speed per second is much lower than the interface can handle -- perhaps there are spikes that cause drops for only small numbers of milliseconds. Perhaps various coalescing would hide this effect -- or perhaps increase it on the receiving interface? Do queues make a difference here? Example: So given if this is linear down to the MS we would have 1Mbit/MS, and if Wireshark isn't distorting what I see, should I see drops when I have a spike beyond 1Mbit?

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Fedora 17 transparent Ethernet Bridge not forwarding IP traffic

  - by mcdoomington

  I am running on Fedora 17 with the latest ebtables and have been trying to setup a transparent bridge - using the following script, I send a ping through the bridged host and only see the requests on the bridge (among other traffic from eth0), BUT, arps and arp replies are making it through. My host is setup - Client 192.168.1.10 <-- eth0 -- eth2 192.168.1.20 Ethernet script: #!/bin/sh brctl addbr br0; brctl stp br0 on; brctl addif br0 eth0; brctl addif br0 eth2; (ifdown eth0 1>/dev/null 2>&1;); (ifdown eth2 1>/dev/null 2>&1;); ifconfig eth0 0.0.0.0 up; ifconfig eth2 0.0.0.0 up; echo "1" > /proc/sys/net/ipv4/ip_forward; ebtables -P INPUT DROP ebtables -P FORWARD DROP ebtables -P OUTPUT DROP ebtables -A FORWARD -p ipv4 -j ACCEPT ebtables -A FORWARD -p arp -j ACCEPT Any assistance would be great!

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >