Search Results

Search found 6497 results on 260 pages for 'usb appliance'.

Page 124/260 | < Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >

  • How do I unmount a charging device in Linux?

    - by PeanutsMonkey
    I have a mobile device attached via USB to a Linux box and wish to unmount it. I ran the command fdisk -l however it does not list a mount point. I then ran the command lsusb which yielded the screenshot below. I then proceeded to search the /dev/disk/by-id directory and was found the following file The file is a symbolic link to what appears to be /dev/sdc Questions Why does it not appear when I run the command fdisk -l? How do I unmount it properly without simply yanking the USB cord from the USB port?

    Read the article

  • iMac boot from linux partition on external drive

    - by user74757
    I have the following "setup:" iMac (no internal drive/dead) --------- (Firewire) ------- [[MAC OS X]] | | | | (USB) | | | | [[MISC STORAGE PARTITION] [MISC STORAGE PARTITION] [EXT2 UBUNTU PARTITION]] I routinely use the firewire drive to boot MAC OS X. However, I would like to boot from the linux partition of the USB drive. This linux partition had linux installed on it from a live cd, and during that process, I told the installer to install GRUB on the usb drive (which happened to be /dev/sdd). My question is, how do I get this disk to show up during the iMac option-boot? Currently, only the firewire MAC OS X option shows up. I have read about rEFIT, but that appears to install it to the Mac OS X disk (would that still work?)... Also mentioned was installing rEFIT to the internal EFI system partition, but I don't know if that is wise.

    Read the article

  • How to charge an iPhone on a Windows PC without Installing iTunes

    - by Martin Hollingsworth
    I want to be able to charge my iPhone on my work computer, which is running Windows Server 2008 SP1 64-Bit. When I plug the iPhone in with the USB cable, it will not charge. Windows attempts to locate a driver for the device but only comes up with a generic Camera device and even if I allow that to be installed, the iPhone still does not charge. I have checked the computer's BIOS settings and did not find anything relating to power on the USB devices. I also tried this on ports at the back of the computer in addition to those on the front. The PC is a Dell Optiplex 780. As far as I can tell USB devices do not charge unless Windows has installed an appropriate driver. Since it is a work computer I do not want to install iTunes which does include a driver. I have a workaround that I will post as an answer for reference.

    Read the article

  • I believe I need a wireless access point, but can I do it with a wifi router?

    - by Flotsam N. Jetsam
    My needs are simple, I think: I have a laptop upstairs with a usb wifi that I use to connect to my neighbor's wifi which I share (with their knowledge). I have a laser printer downstairs that my wife doesn't wants to stay down there (big, bulky and ugly), but that we both need to print stuff off. It has wired networking and I have wired hub and router down there. The usb wifi on the laptop has absolutley the best reception I've ever seen or heard of. I cannot get onto the neighbor's net with the thing downstairs though--sortof in the ground. What do I need downstairs to give printer access to my laptop wirelessly? One thing I can't do in this solution is have a computer on downstairs, so I would think that would eliminate a usb solution.

    Read the article

  • PS/2 mouse works with Windows 7 32-bit but not recognised by 64-bit, What to do?

    - by Bogan
    Our USB mouse was stolen and a PS/2 OK_520 Mouse that works OK on my Medion PC, running Windows 7 32-bit, if plugged in before booting, is not recognised by Windows 7 64-bit on a Dell INSPIRONone_19T with a 19" Touch Screen. (It is a communal computer available to all residents.) A USB mouse works OK and the Update Driver option reports: 'driver is up to date'. Without the USB Mouse, Device Manager/Mice shows only the Touch Screen as a Mouse. The Add New Hardware option searches but shows nothing and the Troubleshooter says ' device possibly not recognised, alterations made to system, try again.' but it is still not recognised after repeated re-boots. The BIOS does not seem to have any option to enable a PS/2 Mouse. The Mouse is very old so maybe it is not 64-bit compatible, or there is no 64-bit driver for one, but how to get one if the device is not recognised?

    Read the article

  • How is it possible for SSD's drives to have such a good latency?

    - by tigrou
    First time i read some information about SSD's, i was surprised to learn they internally use NAND flash chips. This kind of memory is generally slow (low bandwidth) and have high latency while SSD's are just the opposite. But here is how it works : SSD drives increase their bandwidth by using several NAND flash chips in parallel. In other words, they do some data striping (aka RAID0) across several chips (done by the controller). What i don't understand is how SSD's drives have such a low latency, whereas they are using NAND chips? (or at least lot better than what a typical single NAND chip would do) EDIT: I think under-estimate NAND chip capabilities. USB drives, while powered by NAND's are mostly limited by USB protocol (which have a pretty high latency) and the USB controller. That explain their poor performance in some cases.

    Read the article

  • How to install Windows on a laptop with no CDROM drive?

    - by Jason Kester
    I have an old Thinkpad X60 that I'd like to wipe clean and rebuild. Seeing as this machine doesn't have an optical drive, what's the easiest way of installing Windows XP? I have an external USB hard drive available. Would it be possible to run the install from that instead? Otherwise, what options do I have? Edit: assuming we're using a USB mass storage device... Is there a BIOS setting that I would need to change, or will it configure itself automatically? Would the USB drive need to be configured in any special manner, or would simply having a copy of the Windows CD files in a directory there be sufficient? Since the first couple answers that came in were basically "yes", I guess I didn't phrase my question correctly. I'm asking for detailed instructions on how to do this, not just a sanity check that I'm headed in the right direction. Thanks!

    Read the article

  • What are my options for booting OSX 10.6 when my DVD drive is broken?

    - by Kev
    I'm about to completely re-pave my Mac Mini but the DVD drive has died on me which means I can't boot from the installation media. I know I can boot from a USB stick but I don't have one available, what are my options given the following hardware at hand? Netgear ReadyNAS Duo NAS (NIC or USB only, no Firewire) USB HDD (no Firewire) I've ripped an ISO of the installation disk, can I somehow get the Mini to boot from this image using one of the above? If I decide not to re-pave but just upgrade, can the Mac be upgraded just using an OSX 10.6 ISO image on its disk?

    Read the article

  • Clone drive in Windows

    - by ERJ
    I have two 2 TB external USB hard drives, call them HD1 and HD2. HD1 is USB 2, HD2 is USB 3. Each drive contains exactly one NTFS partition. I want to clone HD1 to HD2, because it's newer and much, much faster. What's the best way to do this? I don't want to do a copy-and-paste, I want to clone the whole partition. The new drive is actually a few bytes larger, so this should be possible? I don't have a second drive that can hold the image, so it would have to clone directly to the other disk (not to a file). How can I accomplish this on Windows 7? I know about Clonezilla but I would prefer not to have to boot from a CD or anything, as I don't have the capability to do that right now. I want to know if there's a way to do this while running Windows.

    Read the article

  • What do I need to get so I can upgrade my Thinkpad x61 Tablet hard drive?

    - by user36118
    My Thinkpad X61 Tablet is running out of space, and I would like to give it a bigger drive. I would like to clone the old drive to a bigger new drive. What do I need to get to accomplish this? The fewer things to get, the better, of course. The easier, the better. My system: Thinkpad X61 Tablet. XP w/ the latest SP. I am OK with XP, and don't want to reinstall it. No optical drive. USB 2.0 connectors (Bootable, I think). Things I have: USB 2.0 external drive housing. USB flash stick (2GB).

    Read the article

  • Mount remote drive by port forwarding

    - by Anushka
    I have a windows 7 computer at home and a remote windows XP machine with an external USB drive attached to it. I would like to be able to copy files to and from home/the remote USB drive. The problem is that the only way of contacting the work computer is by first sshing into a different remote linux machine as there is a firewall that prevents direct internet connection. I can see two possible solutions but I don't know how to do them. Set up winscp using ssh port forwarding via the linux box so that I can copy to and from the two windows machines. I assume that I would need to run an ssh server on the XP machine as well to do this? Mounting the remote USB drive on the remote windows machine from the home XP machine via ssh port forwarding again via the linux box. Does anyone know how to do either solution?

    Read the article

  • KDE Device Notifier and mounted volumes ownership and permissions

    - by nunomaltez
    Hi, When I plug an USB pen to my PC and mount the device using KDE's Device Notifier, the mounted device is owned by my user, who has write permissions. However, when I connect a USB harddisk and mount a partition in the same way, the mounted device is owned by root, and since the owner is the only one with write permissions I can't write to the disk. How do I configure the device notifier's actions to mount the HD with my user as owner, just like it mounts the USB pen? I'm using Fedora 9.

    Read the article

  • Why do I have inconsistent network issues with my laptop's wireless?

    - by Jason
    I'm having trouble with my laptop Internet connection. It's patchy at best and resets or freezes a lot. The signal strength is also random. I thought it might be a driver issue but now I don't know. Three other computers using the same wireless network run well. I've switched out wireless routers so I don't think it's the router. I thought it might be the laptop's internal wireless card but I just bought an external USB network card and I'm still having problems. Specs Lenovo T-60p Windows 7 Ultimate Edition Patches/drivers are up to date I only use one of the below at a time, disabling the other: Intel PRO/Wireless 3945ABG v. 13.3.0.137 (Internal wireless) Medialink Wireless-N USB 2.0 Adapter (USB wireless) Any ideas on what might be the problem?

    Read the article

  • UVC device Logitech WebCam 9000 pro

    - by Pavel
    There is such a good webcam in universe that acts as a "USB Video Class" (UVC - video USB standart interface) - the logitech webcam 9000. UVC offer unified interface allowing to control it or grab a picture from it by any UVC-driver. You need one universal driver and you support all the UVC devices (webcams, video-cameras, video-grabbing-cards etc). For example, in linux - if you have UVC driver - you don't need to think about specific webcam driver for UVC webcam. UVC has unified way that webcam transmit its awailable resolutions and other capabilities, so i see 1600x1200 resolution without any problem. I wonder if windows 7 has UVC. I mean "universal UVC" (-; It says "USB Video Class", but doesn't give resolutions larger than 640x480 and webcam's controls, like 'sharpness', 'focus' and other as linux's driver does...

    Read the article

  • Will readyboost speed up a secondary partion or harddrive?

    - by Sebastian
    I'm building a new computer and plan on using a few spare USB sticks with readyboost to cache disk writes. I'll be running Windows 7 Enterprise SP1 x64 I have a single 2 TB disk, and plan to make a partition for windows (100 GB) and use the rest for data. I know Readyboost will work nicely for the C drive, but am unable to find any information on whether it will accelerate a second drive or partition. Just to clarify, I'm NOT trying to use the harddrive instead of the usb sticks. I'm trying to speed up the second partition using the USB sticks So, will readyboost work for a secondary partion or harddrive?

    Read the article

  • TV Card Problem

    - by MladenB
    I have DVB-T card (CE9500B1) and it doesn't work. I've tried everything I knew (but I don't know much). It doesn't show any problem, but shows "No Signal". I used another TV card USB, found channels, put mine card again, and again nothing. I don't think it's broken, when I put USB in my laptop, it recognizes it. Also, these little lights on USB are never turned on. OS is Win 7. Help, please.

    Read the article

  • Reset disk does not work for different model of computer

    - by dato
    I've created a reset USB disk on my HP computer, with Windows 7 Ultimate 32-bit, and it works fine. However, it does not work for Acer computers (notebooks too), so what is the problem here? I've have created it for the same user named user, and the password is exactly the same as well. Is it possible to show the language bar with a keyboard shortcut at the logon screen in Windows 7? I know I can do it through Control Panel, but I can't log into the system. When I click Reset Passwword, it shows me my USB flash drive and says that the password hint is on this USB drive. Then I click Next and type the new passwword, then confirm this new password, but an error dialog is shown. It says that an error occured when trying to change the password for this user-

    Read the article

  • how to disable to automatic wireless interface up in ubuntu? [closed]

    - by Surjya Narayana Padhi
    On my laptop I have a built in wireless card and I got one external connected via usb. By ifconfig command I saw both the cards connects to internet and gets IP. eth1 - the interface my laptop has in-built wlan1 - I have connected externally via usb. Now I applied "sudo ifconfig eth1 down" so that i can use only wlan1. But this eth1 goes down for sometime and then come up again automatically. So I am not able to test my externally usb connected wifi adapter. Can anyone suggest me way to disable eth1 interface?

    Read the article

  • Western Digital Caviar SE16 not recognized

    - by NStorm
    Before I start, I have been looking at quite a few websites and I still have not found an answer to my problem. I have been building my own computer recently and I have just received the hard drive (WD Caviar SE16 WD5000AAKS) I was planning to put in my computer. After connecting the SATA power cable (99.99999% sure it is connected correctly) and the SATA cable to my motherboard (ASUS M5A78L-M/USB3) I booted my computer into a Linux Mint 13 XFCE 64-bit live USB expecting to see a hard drive when I came to install. Sadly when I checked the only hard drive that was showing was /dev/sda which was my USB with the Linux files on it. I also checked gparted and no hard drive other than my USB was showing up there either. Lastly I checked my BIOS and no matter what SATA port I connected the HDD to it wouldn't show up there either. Does anyone have any advice? Some images of my set-up which could help are bellow: Thanks in advance, Nick

    Read the article

  • "wrong fs type, bad option, bad superblock" error while mounting FAT Drives

    - by cshubhamrao
    I am unable to mount any fat32 or fat16 formatted usb disks under Ubuntu 13.10. The thing here to note is that it is happening only with fat formatted Disks. ntfs, ext formatted external usb disks work well (I tried formatting the same with ext4 and it worked) While mounting via nautilus: Error while mounting from terminal: root@shubham-pc:~# mount -t vfat /dev/sdc1 /media/shubham/n mount: wrong fs type, bad option, bad superblock on /dev/sdc1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so As suggested by the error: Output from dmesg | tail root@shubham-pc:~# dmesg | tail [ 3545.482598] scsi8 : usb-storage 1-1:1.0 [ 3546.481530] scsi 8:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5 [ 3546.482373] sd 8:0:0:0: Attached scsi generic sg3 type 0 [ 3546.483758] sd 8:0:0:0: [sdc] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 3546.485254] sd 8:0:0:0: [sdc] Write Protect is off [ 3546.485262] sd 8:0:0:0: [sdc] Mode Sense: 43 00 00 00 [ 3546.488314] sd 8:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3546.499820] sdc: sdc1 [ 3546.503388] sd 8:0:0:0: [sdc] Attached SCSI removable disk [ 3547.273396] FAT-fs (sdc1): IO charset iso8859-1 not found Output from fsck.vfat: root@shubham-pc:~# fsck.vfat /dev/sdc1 dosfsck 3.0.16, 01 Mar 2013, FAT32, LFN /dev/sdc1: 1 files, 1/1949978 clusters All normal Tried re-creating the whole partition table and then formatting as fat32 but to no avail so the possibility of corrupted drive is ruled out. Tried the same with around 4 Disks or so and all have the same things

    Read the article

  • How do I refresh Disk Utility?

    - by detly
    I do a lot of live system building, which eventually involves imaging a USB drive with the built binary image: dd if=binary.img of=/dev/sdX sync ...where /dev/sdX is a USB drive. As part of my workflow, I like to have Ubuntu's Disk Utility open so I can verify the drive letter and unmount anything that gets mounted automatically. I also use it to create extra partitions for persistence. The trouble is, after writing the image to the device — and even after the sync operation — Disk Utility doesn't show the new partition. It just shows free space. GParted sees it and fdisk sees it. Even after closing and opening Disk Utility, it still shows only free space. If I click "Safe Removal" and physically unplug and replug the USB drive, Disk Utility will then see the partition. Why do I need to remove and re-insert the drive for Disk Utility to see the partitions on it? Can I force Disk Utility to update its information without needing to do this? (using Disk Utility 3.0.2 under Ubuntu 11.10.)

    Read the article

  • Why is my Internet connection randomly dropping?

    - by Jeanno
    Ever since I have installed 12.04 (clean install not an upgrade), i have been having a drop in the Internet connection. The drop in the connection can be anything from 15 seconds to about 3 mins, and then the connection comes back. This behaviour happens while I am actively browsing the Internet, or if I wake up the computer and open Firefox (sometimes I have connection and sometimes I don't) . Please note that when the internet connection is on, it is not slow (as speedtest.net results show) In the beginning, I thought it was a problem with the driver r8169 for my RTL8111/8168B Ethernet card, so I downloaded the r8168 from Realtek website, followed the detailed instructions (blacklisted r8169, changed the file to '.bsh' ...), but still the same problem persisted. So I switched to a wireless connection, and I got the same problem with internet connection dropping randomly. Any ideas? Thanks in advance Output from 'lspci -v' Code: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f8000000-fa0fffff Prefetchable memory behind bridge: 00000000d0000000-00000000dbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f4000000-f60fffff Prefetchable memory behind bridge: 00000000c0000000-00000000cbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at f6108000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f6107000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f6100000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fa400000-fa4fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Prefetchable memory behind bridge: 00000000dc100000-00000000dc1fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fa300000-fa3fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa200000-fa2fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f6106000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation P67 Express Chipset Family LPC Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel modules: iTCO_wdt 00:1f.2 RAID bus controller: Intel Corporation 82801 SATA Controller [RAID mode] (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 42 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at f6105000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: Dell Device 04a7 Flags: medium devsel, IRQ 5 Memory at f6104000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at f8000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=128M] Memory at d8000000 (64-bit, prefetchable) [size=32M] I/O ports at e000 [size=128] Expansion ROM at fa000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fa080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 02:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f4000000 (32-bit, non-prefetchable) [size=32M] Memory at c0000000 (64-bit, prefetchable) [size=128M] Memory at c8000000 (64-bit, prefetchable) [size=64M] I/O ports at d000 [size=128] Expansion ROM at f6000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f6080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 03:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fa400000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 51 I/O ports at c000 [size=256] Memory at dc104000 (64-bit, prefetchable) [size=4K] Memory at dc100000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 03-00-00-00-68-4c-e0-00 Kernel driver in use: r8168 Kernel modules: r8168 05:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) (prog-if 10 [OHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at fa300000 (64-bit, non-prefetchable) [size=2K] I/O ports at b000 [size=256] Capabilities: [50] Power Management version 3 Capabilities: [80] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [98] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [130] Device Serial Number 00-10-dc-ff-ff-cf-56-1a Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 06:00.0 SATA controller: JMicron Technology Corp. JMB362 SATA Controller (rev 10) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 19 I/O ports at a040 [size=8] I/O ports at a030 [size=4] I/O ports at a020 [size=8] I/O ports at a010 [size=4] I/O ports at a000 [size=16] Memory at fa210000 (32-bit, non-prefetchable) [size=512] Capabilities: [8c] Power Management version 3 Capabilities: [50] Express Legacy Endpoint, MSI 00 Kernel driver in use: ahci Note that my wireless card is not showing, I have the Ralink 3390 card (which apparently does not show up on Ubuntu for some reason), however I am able to connect to wireless network and connect to the internet (when it is working)

    Read the article

  • How to set acpi=off for installation?

    - by Johan Helgø
    I'm trying to install Ubuntu 12.04 LTS 64bit from a USB created in Windows using the recommended software from pendrivelinux. The USB is tested on two laptops and works fine. The install does not work on my desktop PC, it either hangs with lots of text on the screen, or it just gives me a screen with garbled colors. Right now it hangs on "[3.925311] Initializing USB Mass Storage driver...", but it hangs on different spots every time I try. I know that acpi=off will fix this. On older versions, there used to be a pink screen with the icon of a keyboard, at that screen I could press ESC, and I would then get a long list of languages, I could choose English, and then I would get options for setting acpi=off, then install without any problems. This new install menu does not have those options. The (now black and white) "Installer boot menu"'s advanced options is blank. There simply are no advanced options. If I go to help, then press F6, I get to a help screen describing the different boot parameters. I see examples of writing "Install acpi=off" However, writing "install acpi=off" it gives an error saying "could not find kernel image: install". How can I install Ubuntu 12.04 with acpi=off? (Oh, btw, nothing happens if I press F6 in the "Installer boot menu")

    Read the article

  • How to Recover that Photo, Picture or File You Deleted Accidentally

    - by The Geek
    Have you ever accidentally deleted a photo on your camera, computer, USB drive, or anywhere else? What you might not know is that you can usually restore those pictures—even from your camera’s memory stick. Windows tries to prevent you from making a big mistake by providing the Recycle Bin, where deleted files hang around for a while—but unfortunately it doesn’t work for external USB drives, USB flash drives, memory sticks, or mapped drives. Luckily there’s another way to recover deleted files. Note: we originally wrote this article a year ago, but we’ve received this question so many times from readers, friends, and families that we’ve polished it up and are republishing it for everybody. So far, everybody has reported success! Latest Features How-To Geek ETC How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin The How-To Geek Video Guide to Using Windows 7 Speech Recognition How To Create Your Own Custom ASCII Art from Any Image How To Process Camera Raw Without Paying for Adobe Photoshop What is the Internet? From the Today Show January 1994 [Historical Video] Take Screenshots and Edit Them in Chrome and Iron Using Aviary Screen Capture Run Android 3.0 on a Hacked Nook Google Art Project Takes You Inside World Famous Museums Emerald Waves and Moody Skies Wallpaper Change Your MAC Address to Avoid Free Internet Restrictions

    Read the article

  • Ubuntu 12.04 taking too much time to boot

    - by adarshdinesh
    Ubuntu 12.04 is taking much time for booting, Here is the system kernel message while booting .It is showing that some anacron was killed ,why ? and how to fix the problem ? [ 2.241047] scsi6 : usb-storage 2-1.6:1.0 [ 2.241501] usbcore: registered new interface driver usb-storage [ 2.241895] USB Mass Storage support registered. [ 3.240670] scsi 6:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 3.241791] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.243083] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 12.568641] Adding 4037904k swap on /dev/sda3. Priority:-1 extents:1 across:4037904k [ 12.615014] udevd[462]: starting version 175 [ 12.651334] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 12.655283] [drm] Initialized drm 1.1.0 20060810 ................... [ 14.118369] init: alsa-restore main process (982) terminated with status 19 [ 14.252595] init: anacron main process (1033) killed by TERM signal [ 14.285763] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 14.285841] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 14.285925] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 14.285991] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 14.615073] init: plymouth-stop pre-start process (1222) terminated with status 1 [ 16.447287] wlan0: authenticate with c0:8a:de:7c:60:e8 (try 1) [ 16.448858] wlan0: authenticated [ 16.453405] wlan0: associate with c0:8a:de:7c:60:e8 (try 1) [ 16.456392] wlan0: RX AssocResp from c0:8a:de:7c:60:e8 (capab=0x431 status=0 aid=2) [ 16.456398] wlan0: associated [ 16.457014] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 16.457017] ieee80211 phy0: brcmsmac: brcms_ops_bss_info_changed: associated [ 16.457019] ieee80211 phy0: changing basic rates failed: -22 [ 16.457021] ieee80211 phy0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 16.457226] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 16.654196] ieee80211 phy0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 17.823565] ieee80211 phy0: wl0: brcms_c_d11hdrs_mac80211: txop exceeded phylen 180/256 dur 1946/1504 [ 18.220865] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 26.881422] wlan0: no IPv6 routers present [ 68.228293] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 73.240133] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 76.574490] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 102.180006] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 103.100984] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 124.171624] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement)

    Read the article

< Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >