Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 124/391 | < Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >

• Configuring Wireless on Cisco 851W

  - by Aequitarum Custos

  Either a powersurge or something caused our router's configuration to get wiped, and our last backup was before the wireless network was setup. We have not been able to reconfigure the wireless since then, so was curious if anyone here would be able to determine what configuration is needed. We are using a Cisco 851W running 12.4(15)T9 We would like to use WPA encryption, and have it on the same network as the rest of the office network. Config file is below: User Access Verification Building configuration... Current configuration : 3857 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service dhcp ! hostname BOB ! boot-start-marker boot-end-marker ! enable secret 5 ********************* ! no aaa new-model ! ! dot11 syslog no ip source-route ! ! ip cef no ip bootp server ip domain name BOB.com ip name-server 61.11.1.1 ip name-server 61.11.1.2 ! ! ! username BOBB privilege 15 password 7 ************************* ! ! archive log config hidekeys ! ! ip tcp synwait-time 10 ! ! ! interface FastEthernet0 no cdp enable ! interface FastEthernet1 no cdp enable ! interface FastEthernet2 no cdp enable ! interface FastEthernet3 no cdp enable ! interface FastEthernet4 description WAN Connection$ETH-WAN$ ip address 61.11.1.14 255.255.254.0 ip nat outside ip virtual-reassembly duplex auto speed auto no cdp enable ! interface Dot11Radio0 no ip address shutdown ! encryption mode ciphers tkip speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.20 ip access-group Guest-ACL in no cdp enable ! interface Vlan1 description Internal Network ip address 192.168.2.60 255.255.255.0 ip nat inside ip nat enable ip virtual-reassembly ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 61.11.2.14 ! ip http server no ip http secure-server ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended Guest-ACL deny ip any 192.0.0.0 0.0.0.255 permit ip any any ! access-list 1 permit 192.0.0.0 0.0.0.255 access-list 100 remark SDM_ACL Category=2 access-list 100 permit ip 192.0.0.0 0.0.0.255 any no cdp run ! control-plane ! !

  Read the article

• Internet connection slower than network connection speed

  - by Mike Pateras

  I've got a computer connected to a wireless router on a different floor. When I look at the network connection, I'm told the signal strength is low, and that I've got a connection of about 26mbps (often higher). However, my internet connection on that machine is very slow. Speedtests show it at about 1-2mbps, and it really shows when loading pages and video. I have fiber optic internet access, and the machine that's connected to the router/modem via cable gets the 20mbps on speed tests, and is extremely fast in every day use. My question is, is the advertised 26mbps+ connection speed perhaps inaccurate, and that my wireless bandwidth is the likely bottleneck here? Or is the signal strength what's key here? And what might I do about this? Power cycling the router helped a bit, a speed test went as high as 6mbps after doing that.

  Read the article

• dialup connection script

  - by BParker

  I've just started working for a company who produce a specialist modem. In the test department they simulate actual use with a bunch of pc's acting as clients connecting over this modem. As such each needs to dial a set of dial-up connections. Each of these has to be created manually, and currently takes quite a while on each machine, so i was hoping to be able to automate the creation process. Back in the early days of the internet i remember getting CD's from ISP's where the dial-up connection was configured automatically, and i was wondering if anyone lknew how to do this, or if they could point me in the direction of a tutorial about it. To be clear, i don't want to automate actually dialing the connection, but i do want to run a script which creates the icons in the networking applet that allows us to dial these connection. Thanks in advance!!!

  Read the article

• How can email possibly be routed to the right place with no to: address?

  - by agent154

  I'm no novice on networking technology, but one thing I don't really know much about in detail is email and headers. How does email work SPECIFICALLY? I'm getting spam in my hotmail inbox when I've made painful attempts to not give out my actual email. I use my own domain name to forward email to my inbox using several aliases. Yet now I'm getting spam with no address in the to: line, or also "undisclosed recipients". Looking at the headers is of no help whatsoever. So from a technical standpoint, I have to wonder... if I send an email to a certain address in my personal domain and it gets forwarded to my hotmail account, how does hotmail know what inbox to dump the message in if that address is not listed in the headers?

  Read the article

• Multicast accross the subnets

  - by Hasan Khan

  My application sends some UDP packets on a multicast address. In our office we have 3 subnets connected via routers. Sitting in my subnet I'm able to ping the IP of the other subnet. Will multicast packets cross my subnet and reach the machines of other subnets? Or router will need some configuration? Or do I have to program a bridge for it? Please note that I do not know anything about Networking. Kindly tell me something that I can ask my network admin to do.

  Read the article

• Wall jacks to patch panel?

  - by rj454me

  OK, I'm by no means a seasoned networking pro and I had no say so in the design of our current server room which is in dire need of an extreme makeover. Basically, in our server room we have 12 wall plates with 4 RJ-45 ports on each - 48 total RJ-45 ports. From these 48 ports is a spaghetti bowl of network cables feeding our servers located in a rack - there is no patch panel currently, just straight from the wall jack to each server. What I was wondering is, is it feasible to mount a 48 port patch panel in our server rack and feed into this patch panel from the wall jacks (of course nicely routing this cable through some new cable trays)? We really don't have the funds to mount the patch panel and have it fed directly from the switches in the telcom closet which is several hundred feet away. Current: Switch (Telcom Closet) - Wall Jacks - Servers Proposed: Switch (Telcom Closet) - Wall Jacks - Patch Panel - Servers

  Read the article

• Hostname problems in CentOS 5.5

  - by spoon16

  I just set up a CentOS 5.5 machine on my local network and attempted to modify the hostname by editing /etc/sysconfig/network file. When I'm logged in locally the change to the hostname is reflected and seems to be working fine. When I open a SSH session via PuTTY from Windows this is what I see at the prompt: [root@? ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes HOSTNAME=mini.local [root@? ~]# sysctl kernel.hostname kernel.hostname = ? [root@? ~]# hostname ? [root@? ~]# hostname -f hostname: Unknown server error A couple of other symptoms that may be helpful in troubleshooting this problem. I can ping the CentOS box from my Windows machine via IP but not hostname. Also, my Netgear router does not display the hostname when I view the "Connected Devices", I do see the mac address and the proper IP listed though. How can I make it so that the hostname is properly propagated throughout my network?

  Read the article

• XP Mode as a server, Win 7 as a client

  - by Spyro

  I have two virtual machines (XP Mode). They are connected to each other by a network setting - Internal Network. It is the only working setting. This is the only way I got two virtual XP to ping each other. Now I want to connect each of them from the application that runs on Windows 7 which is hosting both virtual machines, but I can't do that. The firewall on both XP-Mode machines is disabled. Any other networking setting added as additional adapter on Xp-Mode machine does not allow me to connect from Windows 7. So my question is this - how to enable connection from Windows 7 application to XP mode application (client - server)? Point 2 (pass message) work perfectly because of the "internal network" setting. The problem is point 1 and 3.

  Read the article

• How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

  - by user60813

  Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

  Read the article

• Automatically generated /etc/hosts is wrong

  - by Niels Basjes

  I've created a kickstart script to install CentOS 5.5 (32bit) in a fully automated way. The DNS/DHCP setup correctly gives the system the right hostname in both the forward and reverse lookups. dig node4.mydomain.com. +short 10.10.10.64 dig -x 10.10.10.64 +short node4.mydomain.com. In the state the installed system is right after the installation completed is as follows: cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes GATEWAY=10.10.10.1 HOSTNAME=node4.mydomain.com echo ${HOSTNAME} node4.mydomain.com cat /etc/hosts # Do not remove the following line, or various programs # that require network functionality will fail. 127.0.0.1 localhost.localdomain localhost ::1 localhost6.localdomain6 localhost6 10.10.10.64 node4 My problem is that this automatically generated hosts file is slightly different from the way I want it (or better: the way Hadoop wants it). The last line should look like this: 10.10.10.64 node4.mydomain.com node4 What do I modify where to fix this? Thanks.

  Read the article

• How can I fix my Virtual PC 2007 network configuration

  - by DanJ

  Hi, I have installed Windows Virtual PC 2007 on my Windows 2003 R2 Server. I have installed a virtual Windows XP. I have configured the virtual PC to use Shared Networking (NAT) I have disabled the firewall on the virtual windows XP The problem: I am unable to PING from Windows 2003 (the host) to the Windows XP (virtual) I do have normal traffic from the virtual to the internet Could this problem be related to routing? How I can I fix this network configuration to allow for the following traffic: 1. From Virtual to Internet 2. From Host to Virtual 3. If possible, from Internet to Virtual on pre-defined ports (port forwarding?) Thanks

  Read the article

• ubuntu server 10 - slow and can't remove desktop environment

  - by Alex

  i'm running ubuntu server 10.10 with the desktop environment. simple page requests are taking over 5 seconds even when connecting to the server through our local network. i believe this is partially related to having the desktop environment installed, as the server worked faster (but not as fast as it should considering that it's on the local network), but tasksel fails every time (aptitude failed 100). my knowledge of networking and linux in general is limited. would really appreciate ideas on how i can troubleshoot this problem. oh also, in the system monitor, one of the processors is almost always around 100%. i doubt this is normal too....

  Read the article

• How to enable printer settings over Jetdirect on HP 4100N

  - by zsero

  I have a HP 4100N printer and I am using it over network. Previously I was able to access the printer settings over internet, but now the only thing visible is Device Info and Networking. I can connect to the web server and I can set all the network related settings, but that's not what I want. There should be a supplies, config, print info, etc. page, what are not visible now. Can you tell me what setting should I set to enable this printer config page on the webserver? The printer is a HP 4100N and the network card is J4169A (Jetdirect 610n).

  Read the article

• setting up delegate or smtp forwarding

  - by cotiso

  for work we have a remote dedicated server to run our webservice that also runs our email services, at home(comcast residential internet) i cannot send mail using the dedicated server's SMTP, comcast spits back a error saying i can only use their SMTP server for sending mail at work(comcast business internet) we can use our dedicated server for sending mail with no problem so i set up a box at work to forward smtp traffic, i'm new to all this networking stuff by the way i used delegate to forward smtp traffic, can someone point me in the right direction on how to use this program(delegate) to fix our issue the delegate command i used to test is : delegated -P25 SERVER="smtp://dedicated.server.com:25" PERMIT=":::" -v i also opened up port 25 on the router so it points to my boxes ip are there any other ways to fool comcast into thinking im using my works ip to send mail, my coworkers and i are unable to send mail from home for some time now thanks

  Read the article

• Why would you use EAP-TTLS instead of PEAP?

  - by Ivan Macek

  As I understood EAP-TTLS and PEAP share same level of security when implemented in wireless networks. Both only provide server side authentication via certificate. The drawback of EAP-TTLS can be non native support in Microsoft Windows so every user has to install additional software. The benefit of EAP-TTLS can be support for less secure authentication mechanisms (PAP, CHAP, MS-CHAP) but why would you need them in modern and properly secure wireless system? What are you opinions? Why should I implement EAP-TTLS instead of PEAP? Let's say that I have most Windows users, medium Linux users and least iOS, OSX users.

  Read the article

• cannot access my own computer through My Network Places

  - by vgv8

  My home Windows XP Pro SP3 machine is DHCP client receiving configurations from ISP. Trying to access in WindowsExplorer -My Network Places - Microsoft Windows Network shows Workgroup with a delay of 3 min and then popups messagebox: Microsoft Windows Network Workgroup is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.The list of servers for this workgroup is not currently available OK I am logged-in as local machine Administrator. The internet is accessible (I am writing this post through it) The Firewall is disabled The "Computer Bowser" and all networking services, I could find, are running Control Panel -- Network Connections -- Properties (of connection) --- Internet Protocol (TCP/IP), btn Properties --- --- tab General, btn "Advanced..." -- tab WINS-- rbtn "Enable NetBIOS over TCP/IP" checked Why cannot I access my own PC (and shares on it) through My Network Places What is the possible problem? How to daignose the problem?

  Read the article

• Network access to VM only from host ...

  - by Jamie

  I'm trying to do some testing of Ubuntu 10.04 Beta 2 Server in a VMWare environment. The host is XP, and the VM software is VMPlayer. Problem is, I want to be able to see the VM from the network, not just from the host. I can SSH into the VM from the host, but from any other machine on the network I can't even get the VM to respond to a ping. Going the other way (from the VM out) isn't a problem at all. The VM software did an 'easy installer' so I'm not really sure what was going on with the networking. Suggestions?

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - Setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. My ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• VPN: What should my Gateway remote ID be?

  - by Lynn Owens

  I have a Netgear ProSafe UTM. I set the Gateway local ID to it's WAN IP. But I'm not sure what to put for it's Remote ID. I want to be able to connect to it from a laptop across the internet. I can chose between: Remote IP FQDN Client FQDN Cert DN Frankly I've tried them messing around with them all but I'm just shooting in the dark, and the help desk docs are worthless. Also, Googling around seems to end up with lots of pages not really related to what I want. A lot of pages on configuring Cisco or Windows home networking or privacy advocates.

  Read the article

• Process of carrying out a BER Test

  - by data

  I am subscribed to an ISP supplying a 3meg ADSL line. Lately (for the last 4 weeks) speeds have dropped from the usual average downstream speed of ~250kbps to just 0.14Mbps (according to speedtest.net) and employees are complaining about lack of access to the server. I have been calling customer support and logging calls for the last 3 weeks, but they have been unable to determine the source of the problem other than carrying out a few bitstream tests and checking the DHCP renewal times. I am going to call back and suggest carrying out a BER test. What type of equipment is needed to carry out this test? I have access to a wide range of Cisco networking equipment. Other: We don't need a leased line as there are less than ten employees.

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• VPN within a VM to allow for internet access on the host

  - by David Durrant

  I have a network connection (created under Networks and Sharing) that I use to connect to a customer's site. But when I use this to connect to the site, I loose all access to the public internet, and can only access customer specific items. I want to circumvent this issue by creating a VM and then utilizing the VM to connect to the network location and interact within the customer's domain, while leaving my host machine open to the internet. I'm not extremely familiar with networking, but I have a few basic skills. Please let me know if this is possible and what the correct procedures are. I already have a VM created with VirtualBox, and both the host and guest are running Windows 7 x64. I have created duplicate VPNs already, but can only connect successfully on the host machine.

  Read the article

• Vmware Workstation Development Server on Laptop

  - by Koobz

  I'm running an Ubuntu guest OS on my Windows 7 laptop. Currently, I have it set up for bridged networking. The guest is os is configured for a static ip of 192.168.1.115, which depending on the network I'm connected to, may not be available. When I want to view my development work I hit that up in my web browser. I'm really looking for the following scenario: 1) My guest OS ip address stays constant. 2) I can access my guest os even if I don't have an internet connection, or a lan/router. 3) I can share files with my guest/host. How does one accomplish this using VMware Workstation?

  Read the article

• Where is debian storing its network settings?

  - by user13743

  I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

< Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >