Search Results

Search found 91048 results on 3642 pages for 'dell user'.

Page 13/3642 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• Dell Latitude E6400 power button and wireless not working or only working intermittently

  - by Droid

  The power button on the laptop stopped working randomly as of a day or two ago. I can only power the laptop on if its attached to a docking station, on which I can use the power button to turn on/off the laptop. Today the wireless card stopped working (the wifi light does not turn on, even after I turn on the wireless switch). What is the problem and how can I fix it? The laptop is about 1 year old. I have not dropped it, but do carry it around a good amount, including docking it/undocking it frequently.

  Read the article

• Fetch User's User agent,IP address

  Here i am going to give you example to fetch or to show or to store user's mobile/pc user agent, IP address.

  Read the article

• Dell Inspiron 1525 - internal hard drive not detected

  - by GingerT

  Others have asked about this issue but had intermittent access to their HD, therefore their results did not apply to this situation. I have tried reseating the HD to no effect. I also tried booting from the Internal HD to no effect. Next step get a connector cable and move the data to a different HD, or send in for HD recovery? Any suggestions?

  Read the article

• Dell Vostro Desktop error

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• Dell Vostro Desktop error.

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• Dell Inspiron 1501 battery no longer "recognized"

  - by mwalling

  My parents were on vacation last weekend and franticly called me saying that they couldn't get their Inspiron 1501 to boot anymore without the BIOS whining about the battery. Before this happened, they said the "battery went dead with negligible pre-warning". On bootup, the computer says: WARNING: The battery cannot be identified. This system will be unable to charge this battery. With options to enter the BIOS or continue booting. I got to look at the machine last night. The battery still holds a charge, and will recharge. Windows detects it as a DellPY9617 battery manufactured by "DynaPack". I didn't get the BIOS revision, but the machine's ship date was 7/21/2007. The recommendations I could find on the internet varied from "discharge the battery completely" to "your computer is too old" to "update the BIOS", and wanted a more specific answer before doing something drastic.

  Read the article

• "Cannot open user default database" error with "User Instance=True"

  - by Keith

  I have a desktop application that uses Sql user instancing. This is my connection string: "Data Source=.\SqlExpress; AttachDbFilename=C:\path\file.mdf; Integrated Security=True; User Instance=True; Connect Timeout=100;" My application creates this DB, downloads a load of data into it from a web service and then does a lot of actions with it. The problem comes when I attempt to re-open the connection. I get a SqlException: "Cannot open user default database. Login failed. Login failed for user 'myDomain\myusername'." This error makes no sense in this context - I have no default database. I'm logging in to an instance created just for the current application, running separately from SqlExpress. There's no other way to connect to this DB. If I start the SqlExpress service and connect to the default instance it won't be visible. It only exists for this application. The file on disk is locked by the SqlExpress instance service running under the application. if I stop the app and restart it the connection works first time, but fails on re-opening. If I just stop the app I can delete the .mdf files and begin again, but it still crashes when I re-open the connection. As my app started the instance running as me my current user should have access to every DB in the instance. This doesn't happen for other users of the same code, which suggests that it's a SQL config issue. Does anyone have any idea what causes this and how to work around it?

  Read the article

• Desktop installation fails on Dell Precision T1600 with Nvidia Quadro card?

  - by Masao

  I'm trying to install Ubuntu 12.04 Desktop on a Dell Precision T1600, however, I get a blank screen with only a blinking cursor in the top left hand corner (this is after the grey screen with the small Ubuntu logo at the bottom). If I remove the Nvidia Quadro 2000 card and plug a monitor into the built-in VGA port, then the installation works fine. Also, I've tried an Nvidia Quadro 2000D by PNY, but I get the same problem. Has anyone installed Ubuntu 12.04 Desktop on a Dell Precision workstation?

  Read the article

• Dell Perc 6i with FreeBSD 8.1 errors with mfi0: COMMAND xxxxxxxx TIMEOUT AFTER xxx SECONDS

  - by jDempster

  We've recently bought two Dell PowerEdge R710 servers with Perc 6i controllers and 6x 135GB SAS Drives. We'd done some pretty extensive testing on a Dell PowerEdge R510 server with a Perc 6i and 4x 135GB SAS Drives running FreeBSD 8.1 for it's wonderful ZFS support and mfiutil. We hadn't had any problems with the R510 and had got to a point where we where happy with the performance of ZFS. Since running FreeBSD 8.1 on the R710 we've been getting errors from the RAID controller. mfi0: COMMAND 0xffffff80005d1770 TIMEOUT AFTER 6178 SECONDS This usually brings the system to a stand still. But it doesn't always happen, and performs very well up until it does happen. We've been running the disk as 3 mirrored drives striped in ZFS. So far we've noticed that running the drives with RAID10 on the RAID seems to work without errors (still testing). At first I thought hardware error as we'd been running FreeBSD on the R510 with the same controller without any issues. But both R710 have the same issue. All controllers are running the same firmware.

  Read the article

• Dell Poweredge 2600 RAID Transfer How-to

  - by DCookie

  Help, please! Hardware: Dell Poweredge 2600 PERC 4 SCSI Drives, 1 standalone 3 in a RAID 5 configuration OS: Windows 2000 Server In other words, a fairly old system. Anyway, we are in the process of taking over support for this site. The current tech wants out and is fading from view fast, so we need to solve this problem: The standalone disk (where the OS was) failed. We've replaced the disk, installed the OS, but need to know exactly how to proceed from here. I've never worked with a RAID system before, so I don't want to touch anything without knowing what I'm doing. We are not certain if the site will want us to attempt to recover the array or wait for the old tech to become available. We have replaced the server with a temporary box, and recovered MOST of the data from an online backup service. However, the other tech failed to backup a part of the data and the only copy of it is on this RAID array. Hence, our caution. We have poked minimally around in the boot-up PERC config utility, and it seems to me that that's where we'll need to be to reclaim the array. Another possibility is that there is some Dell software for the RAID controller we need to acquire. Can anyone provide clues as to how to proceed from here? Any help GREATLY appreciated.

  Read the article

• Strange performance issue with Dell R7610 and LSI 2208 RAID controller

  - by GregC

  Connecting controller to any of the three PCIe x16 slots yield choppy read performance around 750 MB/sec Lowly PCIe x4 slot yields steady 1.2 GB/sec read Given same files, same Windows Server 2008 R2 OS, same RAID6 24-disk Seagate ES.2 3TB array on LSI 9286-8e, same Dell R7610 Precision Workstation with A03 BIOS, same W5000 graphics card (no other cards), same settings etc. I see super-low CPU utilization in both cases. SiSoft Sandra reports x8 at 5GT/sec in x16 slot, and x4 at 5GT/sec in x4 slot, as expected. I'd like to be able to rely on the sheer speed of x16 slots. What gives? What can I try? Any ideas? Please assist Cross-posted from http://en.community.dell.com/support-forums/desktop/f/3514/t/19526990.aspx Follow-up information We did some more performance testing with reading from 8 SSDs, connected directly (without an expander chip). This means that both SAS cables were utilized. We saw nearly double performance, but it varied from run to run: {2.0, 1.8, 1.6, and 1.4 GB/sec were observed, then performance jumped back up to 2.0}. The SSD RAID0 tests were conducted in a x16 PCIe slot, all other variables kept the same. It seems to me that we were getting double the performance of HDD-based RAID6 array. Just for reference: maximum possible read burst speed over single channel of SAS 6Gb/sec is 570 MB/sec due to 8b/10b encoding and protocol limitations (SAS cable provides four such channels).

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• Updating Dell PowerEdge firmware on Ubuntu?

  - by Shtééf

  The company I work for recently got hands on a batch of second hand PowerEdge SC1425 machines. We'd like to put these to good use. Our operating system of choice is Ubuntu Server 10.04 64-bit, which installs just peachy on this type of machine. Now I'd like to install the firmware updates from Dell, which are apparently marked as recommended. This includes the updates for the BIOS, the BMC, and possibly some other hardware. I find it incredibly difficult to locate the files on the Dell website, and install any of them on an Ubuntu system: I downloaded the file OM_6.2.0_SUU_A01.iso. I believe I've read that the SUU DVD should be able to update any recent PowerEdge. Is this correct? Is this the latest version? Besides the version number, does A01 have any meaning? Is this image bootable? (At the moment, I just nosed around with a loop device mount.) Running /bin/bash ./suu from the DVD, I get: # /bin/bash ./suu ./suu: line 262: ./java/linux/i386/bin/java: No such file or directory The file exists and is executable, though. But I cannot execute it directly from the shell either.

  Read the article

• Warnings When Undo Isn't Possible

  - by ultan o'broin

  Enjoyed this post Never Use a Warning When you Mean Undo by Aza Raskin. It makes sense never to warn users if an undo option is possible. The examples given are from the web space. Here's the conclusion: Warnings cause us to lose our work, to mistrust our computers, and to blame ourselves. A simple but foolproof design methodology solves the problem: "Never use a warning when you mean undo." And when a user is deleting their work, you always mean undo. However, in enterprise apps you may find that an undo option isn't technically possible or desirable. Objects may be shared, part of a flow elsewhere, or undoing something committed to the database (a rollback I guess) may not be feasible if it becomes locked by another process. Plus, what constitutes user ownership of objects isn't always clear to users. The implications of delete (and other) actions need to be clearly communicated out in advance. Really, warnings are important in the enterprise space. Data has a very high value, and users can perform a wide variety of actions that may risk that data, not always within the application itself (at browser level, for example). That said, throwing warnings all over the place when an undo option is possible is annoying. Instead, treat warnings with respect. When there is no undo option possible, use warning messages to communicate potentially dangerous or irrecoverable actions or the downstream consequences of user actions on the process or task flow. Force the user to respond to a warning message by using a modal dialog with clearly labeled action buttons. Here's a couple of examples. A great article that got me thinking. Let's see more like that. Let's not forget there's more types of messages than just error messages. User assistance and user experience professionals need to understand when best to use confirmation, information, and warning types too!

  Read the article

• NVIDIA Tesla K20C in Dell PowerEdge R720xd --- power cables

  - by CptSupermrkt

  I am trying to put an NVIDIA Tesla K20C into a Dell PowerEdge R720xd. I'm having a bit of trouble understanding the power requirements of the card. First, here is a picture of two pages of the same manual, which seems contradictory to me. One page says only a single connector is required, while the next page says both are required. The entire manual for the card can be found here: http://www.nvidia.com/content/PDF/kepler/Tesla-K20-Active-BD-06499-001-v02.pdf Here is an photo taken of the power connections on the card: And here is a photo of where those connectors need to go, onto the PCI-E riser of the r720xd: Neither the R720xd NOR the GPU came with the necessary cables. And given what appears to be a contradiction in the GPU manual (above), I'm not even sure at this point what we actually need. I have searched high and low online for things like 2x6 pin PCI-E to 8 pin male-to-male and so on, and for the life of me cannot find what we need. In case anyone needs it, the owner's manual of the R720xd can be found here: ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_poweredge/poweredge-r720xd_Owner%27s%20Manual_en-us.pdf The relevant page is page 68, which clearly indicates that the 8-pin female port on the riser card is for a GPU. The bottom line question: exactly what power cables do we need to buy, and where can we find them?

  Read the article

• Provisioning DELL servers using only linux tools

  - by Krist van Besien

  We have taken delivery of a bunch off Dell Poweredge Rack servers. Unfortunately when ordering it was neglegted to ask for dhcp to be enabled in the built in iDRAC controlers... So they are all stuck on the same IP address. Which means that I'll have to go to each of them individually and configure a new IP in the console... In the future I want to avoid that. Now Dell proposes to deliver the next batch with auto discovery enabled. As I understand this means that when the machine wakes up for the first time the iDRAC will request a DHCP address. The DHCP server then supposedly also provides a "provisioning" server, that provides it with a username and password, and a configuration to be applied. This would allow us to for example configure things like RAID automatically. However, I can't seem to find a way to set up such a provisioning server that does not involve setting up a windows machine. I want to use Linux tools exclusively. Is there a way to do this? I want to just rack servers, switch them on, and then do everything remotely. And that using only linux tools?

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• Windows Vista freezes

  - by Kakurady

  Windows Vista (32-bit) would randomly freeze on my computer, usually 15-30 minutes after login but can happen just after login. All applications would stop responding and the hard drive will not make any sound, and after a while, the mouse cursor will also stop moving. I dual-boot Ubuntu, and that still works fine. It started with the computer freezing when loading Team Fortress 2. Alt-Tab and Ctrl-Alt-Del have no effect, and the hard drive does not make any sound. I tried to verify the game data using Steam and that freezes the computer too. So I stupidly reinstalled the game. Now the game doesn't freeze when it starts, but instead the whole computer randomly freezes. This computer is a Dell XPS M1530 with a 320GB (298GiB) drive (WDC WD3200BEVT-7) split 5-ways, with Windows and Linux a partition each, one more for Linux swap space, and another two partitions for Dell diagnostic program and factory image and drivers. There was once where the hard drive would make clicking noises all day, and only stopped when I rebooted the computer. Since then, the BIOS diagnostics would fail the drive (for "self-test log contains previous errors") whenever ran. (The on-disk diagnostics cannot be run because I overwrote the MBR with GRUB.) Naturally, I thought the hard drive could be the problem. CHKDSK found one bad sector, but this seems to have no effect. System File Checker found two protected files with wrong hashes, one is some kind of IE manifest, and the other is a tcpmon.ini. Neither of them can be restored because their back up copy also have wrong hashes. Nothing about system failures in the event viewer. What should I do next?

  Read the article

• Completely remove user account and create another with same name in Windows 7

  - by TeaJay

  Here's my question simply and then the details in case they help to get me an appropriate answer. Question: How can I completely and permanently delete a user account in Windows 7 so that I can create another one with the same user name without the computer name extension added, eg Jane Smith not Jane Smith.computer name? The details: I just did a clean install of Windows 7 Professional 32 bit. (My laptop crashed, I reinstalled Vista and restored backup files but things weren't working so I decided to just get Windows 7 since I had to start over anyway). I used Windows Easy Transfer to save just about everything, even customizing to include a user's appdata from Windows.old which was created when I reinstalled Vista -- not knowing that another windows.old file would be created with the installation of Windows 7. After installing Windows 7, I used Windows Easy Transfer to transfer the user file, appdata, to the new user account which I gave the same name (Jane Smith) in case having a different name would cause problems with reading files or something. Afterwards, I realized that I did not want ALL of that junk. So, I thought no problem, I'll just delete the user account I just created, nothing lost, and create another one this time transferring only the files I wanted (using the customize option in windows easy transfer). I wanted to keep the same user name, e.g. Jane Smith, so after I deleted the user account I checked the files, and I didn't see. It was late so I went to bed and the next morning I created a new user with that same name (Jane Smith). The files looked fine if I remember correctly. Meanwhile, I updated the computer and it restarted a couple times. As I was moving files to the "Jane Smith" user account file, things weren't working as they should. I was actually moving files to the deleted user account and that the current user account was named "Jane Smith.computer name" and that's where the files needed to go. I don't like this. It's too confusing. I want just "Jane Smith". How can I do this without just changing the user name (which doesn't change it in the file path etc)? I want the first one GONE. If I can't do this, is it a problem to create an account with another name and still transfer files to it without path or other problems? I hope this question makes sense and that someone can help me. Thank you in advance!

  Read the article

• A design pattern for data binding an object (with subclasses) to asp.net user control

  - by Rohith Nair

  I have an abstract class called Address and I am deriving three classes ; HomeAddress, Work Address, NextOfKin address. My idea is to bind this to a usercontrol and based on the type of Address it should bind properly to the ASP.NET user control. My idea is the user control doesn't know which address it is going to present and based on the type it will parse accordingly. How can I design such a setup, based on the fact that, the user control can take any type of address and bind accordingly. I know of one method like :- Declare class objects for all the three types (Home,Work,NextOfKin). Declare an enum to hold these types and based on the type of this enum passed to user control, instantiate the appropriate object based on setter injection. As a part of my generic design, I just created a class structure like this :- I know I am missing a lot of pieces in design. Can anybody give me an idea of how to approach this in proper way.

  Read the article

• Run script after switching user account "to the same account"

  - by Peter Sivák

  In Ubuntu, when I click on Switch User Account... and then choose the same account to log in (for example if my name is John Smith, I click on switch user account and then log into the John Smith account again), how can I run a script after that? (I know, that I can run a script after "first" login by putting it in /etc/profile file, but this script is not executed again when I choose switch user account and then immediately log in back to the same account.)

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• Dell R510 can i go from E5620 to X5690

  - by NJinPHX

  I have a Dell R510 used for a SQl server. Can I go from E5620 to X5690? They are both in the same Intel Xeon 5600 series. But the i did not know if a X (Performance) is interchangeable E (Mainstream). If not then the fastest upgrade i can make will be to another E. thx Intel® Xeon® Processor E5620 (Current) http://ark.intel.com/products/47925 Intel® Xeon® Processor X5690 (Proposed Upgrade) http://ark.intel.com/products/52576 Intel® Xeon® Processor E5649 (Fall back Upgrade) (cant post link)

  Read the article

• Dell Poweredge 2650 RAC Issue

  - by Ryanteck

  I just got a second hand Dell Poweredge 2650 and its working fine. I can access the embedded remote access controller via the Racadm.exe tool (Under wine) but the web based version of it (Which I would prefer to use) has an SSL certificate error. I select continue I know there are risks ect and java starts up. It then gives me the error failed to validate certificate the application will not be executed Is there any way to be able to fix this? *Update Full java error output @ http://paste.ubuntu.com/6352862/

  Read the article

• Dirty Cache Dell Equallogic Storage Array

  - by Jermal Smith

  has anyone ever run into a dirty cache issue with a Equallogic SAN. Even after replacement of the controller cards in the Equallogic Storage Array fails offline with a dirty cache. I have listed steps here on my blog to bring the SAN online again, however this is not the best solution as it continues to fail. http://jermsmit.com/dirty-cache-dell-equallogic-storage-array/ If you have any info on this please share. Thanks, Jermal

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >