Search Results

Search found 3988 results on 160 pages for 'collision resolution'.

Page 133/160 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

  • Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

    - by Casey
    I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

    Read the article

  • Cisco 837 not passing UDP traffic properly (was: DNS query problem)

    - by TessellatingHeckler
    We have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch - LAN. It has been fine for years, suddenly DNS resolution stopped working from the LAN to public DNS servers. No changes that I know of, so I can't revert anything. Current behaviour: DNS requests from the LAN using TCP show up in the oubound firewall log, in the Cisco debug log, in the dns-server-firewall, in tcpdump on the DNS server, the answer comes back, it works fine. DNS requests from the LAN using UDP show up in the outbound firewall log, in the Cisco debug log, but does NOT show in the dns-server-firewall, not in tcpdump on the DNS server, times out. DNS requests from the Cisco using UDP show up in the dns-server-firewall and in tcpdump on the DNS server, answer received, works fine. netcat connections to port 53 or a random port by TCP show up in the dns-server-firewall netcat connections to port 53 or a random port by UDP do not show up in the dns-server-firewall Summary: TCP seems fine throughought. UDP works from the Cisco over the ADSL, and it works from the LAN to the Cisco, but it doesn't seem to cross the Cisco 837 properly. Update: confirmed with netcat that any UDP traffic from the LAN is affected, not just traffic to port 53. Update: If I change the firewall's external IP to any other IP in the subnet, this starts working. When I put it back, it stops working. I now suspect it's an ISP issue (does that sound plausible?), and am removing the Cisco config.

    Read the article

  • How do I force Windows 7 to recognize my Projector?

    - by user63564
    I have a new Dell XPS with an NVIDIA GeForce GT 445M and an old (several years) Epson PowerLite Cinema 550 projector. Windows 7 refuses to recognize that the projector is connected under normal conditions (I'll get to the strange condition in a moment). Here are some things that I have already tried: Confirm that the projector continues to work well on my old Windows XP laptop. Confirm that the video cable (HDMI to HDMI) is connected Make sure the Dell laptop is plugged in to wall power at all times Reboot both the computer and the projector Click "Detect" under the "Connect to an External Display" Windows dialog (no reaction) Click "Rigorous Display Detection" under NVIDIA Control Panel (dialog: none found) Checked "Force Television Detection on startup" under "My display is not shown..." in NVIDIA Control Panel (no effect) Here's where it gets weird... My projector has three states: off, standby and on. Standby means the power switch on the back is on, but the projector is effectively off (no picture, no access to menu or controls). When I plug in the HDMI cable while the projector is in standby, Windows detects the projector! It lets me switch to Duplicate, Extend, or Project Only mode, and adjusts the resolution appropriately. A new Generic Plug-n-Play monitor shows up in my device manager. A "Seiko EPSON PJ" display shows up in my NVIDIA control panel. Then if I turn my projector on, Windows no longer recognizes the display. This is true whether I turn the projector on while the HDMI cable is plugged in, or if I unplug the HDMI cable while turning on the projector. Anyone have any ideas, because I'm completely stumped...?

    Read the article

  • How can I calculate power consumption of my PC in Watt?

    - by Jitendra vyas
    How can I calculate power consumption of my PC in Watt, to prove my House owner ( I live on rent) , my PC doesn't consume much power? He blames me for Huge power bills even he too use Fridge, A.C. etc and his son watch the TV all the time. We both share one Power meter so for bill we pay 50%-50% but He is saying I use PC all the time even night i keep on for downloading. I just want to calculate power consumption of my PC then will calculate monthly expense of unit as per my City's per unit price for power. I've Windows: Microsoft Windows XP Professional 5.1.2600 Service Pack 3 Memory (RAM): 960 MB CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1399.0 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Monitors: 1 - 17inch LCD - LG Screen Resolution: 1280 X 768 - 32 bit Network: Network Present Network Adapters: Bluetooth Device (Personal Area Network) #2 | WAN (PPP/SLIP) Interface CD / DVD Drives: I: ELBY CLONEDRIVE COM Ports: COM1 | COM2 | COM7 | COM8 | COM9 | COM10 LPT Ports: LPT1 Mouse: 3 Button Wheel Mouse Present Hard Disks: C: 29.3GB | D: 29.3GB | E: 97.7GB | F: 97.7GB | G: 211.9GB USB Controllers: 5 host controllers. Firewire (1394): 1 host controllers. Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA #2

    Read the article

  • CENTOS 6 - How to install php-mysql when php-common @remi is present?

    - by Multitut
    I am having troubles adding mysql support for my php installation, this installation was made using a ready to use-package that came with our VPS. This is my php.info: http://snake.quetzalcoatech.com/info.php I am trying to install php mysql using: yum install php-mysql And get this output: Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: mirrors.serveraxis.net * extras: mirror.fdcservers.net * updates: bay.uchicago.edu Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php-mysql.x86_64 0:5.3.3-14.el6_3 will be installed --> Processing Dependency: php-common = 5.3.3-14.el6_3 for package: php-mysql-5.3.3-14.el6_3.x86_64 --> Finished Dependency Resolution Error: Package: php-mysql-5.3.3-14.el6_3.x86_64 (updates) Requires: php-common = 5.3.3-14.el6_3 Installed: php-common-5.3.17-2.el6.remi.x86_64 (@remi) php-common = 5.3.17-2.el6.remi Available: php-common-5.3.3-3.el6_2.8.x86_64 (base) php-common = 5.3.3-3.el6_2.8 Available: php-common-5.3.3-14.el6_3.x86_64 (updates) php-common = 5.3.3-14.el6_3 You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest I am a noob using Linux, so could you tell me which command should I use to install a compatible php-mysql module? Thank you so much!

    Read the article

  • Dual VGA monitors with Quadro FX 580?

    - by dentrasi
    I have a machine with a Quadro FX 580 card (DVI and two Displayport). Attached to it are two 19" Acer screens, which are both (annoyingly) VGA. The first one works perfectly, with a DVI-VGA adaptor. The second one doesn't work. It's got a VGA cable, which goes into a VGA-DVI converted, which then goes into a DVI-Displayport converter. Initally, I was getting 'Cable Unplugged' on the screen, and it couldn't be seen by Windows or the nVidia control panel. After swapping the VGA-DVI adaptor (which works perfectly on another machine), Windows can now see the monitor. The nVidia panel sees the model and native resolution, but I get a constant 'No Signal' error. Switching to the other Displayport makes no difference. I suspect that the card is seeing a DVI connection plugged into it (nVididaCP shows the monitor as having a DVI connection), and it only sending out a digital signal because of this. Does anyone know of a solution (other than trying to get a Displayport-VGA adaptor), or of a way to force the card to see it as VGA? Thanks, ~Dentrasi

    Read the article

  • yum error when installing memcached

    - by Jack
    Hi, trying to install memcached with "yum install memcached" and i'm getting all these errors which I have no idea how to solve. Setting up Install Process Resolving Dependencies -- Running transaction check --- Package memcached.x86_64 0:1.4.5-1.el5.rf set to be updated -- Processing Dependency: perl(AnyEvent) for package: memcached -- Processing Dependency: perl(AnyEvent::Socket) for package: memcached -- Processing Dependency: perl(AnyEvent::Handle) for package: memcached -- Processing Dependency: perl(YAML) for package: memcached -- Processing Dependency: perl(Term::ReadKey) for package: memcached -- Processing Dependency: libevent-1.1a.so.1()(64bit) for package: memcached -- Running transaction check --- Package compat-libevent-11a.x86_64 0:3.2.1-1.el5.rf set to be updated --- Package memcached.x86_64 0:1.4.5-1.el5.rf set to be updated -- Processing Dependency: perl(AnyEvent) for package: memcached -- Processing Dependency: perl(AnyEvent::Socket) for package: memcached -- Processing Dependency: perl(AnyEvent::Handle) for package: memcached -- Processing Dependency: perl(YAML) for package: memcached -- Processing Dependency: perl(Term::ReadKey) for package: memcached -- Finished Dependency Resolution memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(AnyEvent::Socket) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(AnyEvent) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(AnyEvent::Handle) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(YAML) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(Term::ReadKey) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) Packages skipped because of dependency problems: compat-libevent-11a-3.2.1-1.el5.rf.x86_64 from rpmforge memcached-1.4.5-1.el5.rf.x86_64 from rpmforge The perl modules that its complaining about are already installed. Any ideas?

    Read the article

  • Dependency issue installing PostGIS on CentOs 6.3

    - by Nyxynyx
    I am new to linux and is trying to install PostGIS2 after successfully installing PostgreSQL 9.1. The machine is running CentOS 6.3 and has cPanel installed. Problem: When I tried installing PostGIS using yum: yum install postgis2_91 postgis2_91-utils, I get the dependency error below. How should I solve this dependency problem and install PostGIS? Thank you so much! --> Finished Dependency Resolution Error: Package: postgis2_91-utils-2.0.1-1.rhel6.i686 (pgdg91) Requires: perl-DBD-Pg Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libdapserver.so.7 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libdap.so.11 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libgeotiff.so.1.2 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libnetcdf.so.6 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libdapclient.so.3 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libhdf5.so.6 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: librx.so.0 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libogdi.so.3 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libcfitsio.so.0 You could try using --skip-broken to work around the problem ** Found 6 pre-existing rpmdb problem(s), 'yum check' output follows: bandmin-1.6.1-5.noarch has missing requires of perl(bandmin.conf) bandmin-1.6.1-5.noarch has missing requires of perl(bmversion.pl) bandmin-1.6.1-5.noarch has missing requires of perl(services.conf) exim-4.77-1.i386 has missing requires of perl(SafeFile) frontpage-2002-SR1.2.i386 has missing requires of libexpat.so.0 sendmail-cf-8.14.4-8.el6.noarch has missing requires of sendmail = ('0', '8.14.4', '8.el6') Update An error still remains: Error: Package: postgis2_91-utils-2.0.1-1.rhel6.i686 (pgdg91) Requires: perl-DBD-Pg You could try using --skip-broken to work around the problem ** Found 6 pre-existing rpmdb problem(s), 'yum check' output follows: bandmin-1.6.1-5.noarch has missing requires of perl(bandmin.conf) bandmin-1.6.1-5.noarch has missing requires of perl(bmversion.pl) bandmin-1.6.1-5.noarch has missing requires of perl(services.conf) exim-4.77-1.i386 has missing requires of perl(SafeFile) frontpage-2002-SR1.2.i386 has missing requires of libexpat.so.0 sendmail-cf-8.14.4-8.el6.noarch has missing requires of sendmail = ('0', '8.14.4', '8.el6')

    Read the article

  • GTX 280 purple snow on bootup, card works without drivers

    - by Brokar
    i have owned a ASUS GTX280 for 3 years now. The card has been great all along but i started having problems 10 days ago. I was playing Diablo 3 for 1 week on max settings no problems, then suddenly my display kept getting some weird purple/colours as soon as i booted and logged into windows. Went into safe mode, updated drivers and it kept crashing. Formatted PC, fresh windows install with new WHQL drivers again same problem. Uninstalled nvidia drivers and pc has been running great for 4 days now, ofcourse i cannot run games but everything works on 1680x1050 resolution and i can browse internet,watch movies and use my PC for everything but gaming. As soon as i install nvidia drivers PC won't boot. I only wanna game a few hours a week (very busy program with school this month so it might be a blessing that i cannot game) and i would love it if i could keep the card. I am looking to upgrde later on when i will have time for gaming but i wonder if i could still use the card somehow with different/new drivers (tried older drivers that came with the card on a CD aswell) tldr: PC works fine with no nvidia drivers (apart from gaming ofc). Once i install WHQL drivers or older ones, cannot even log into windows. Fix?

    Read the article

  • How to setup DNS server behind a VPN

    - by Brian
    I want to host some websites behind a VPN and I need some help with the finer points of the configuration. Thus far I've settled on OpenVPN + Bind9 and I want to configure the domains like this: External DNS mail.example.com www.example.com vpn.example.com I want to be able to connect to the vpn using 'vpn.example.com'. Once connected I then want to be able to resolve anything which is '*.vpn.example.com' with the DNS server sitting behind the VPN. I know that OpenVPN can push DNS servers to clients when they connect. I am having trouble though with the DNS config, both internal and external. I've gone through a few tutorials etc. and tried to reason about it myself but I'm not getting anywhere. So my main question would be does the above configuration make sense? If so, any general pointers or examples would be greatly appreciated. Here's what I've tried so far based on this tutorial (I've redacted my domain with example.com). When I try the tests with dig at the end to check the resolution is working it fails. db.vpn.example.com $TTL 15m vpn.example.com. IN SOA ns.vpn.example.com. [email protected]. ( 2009010910 ;serial 900 ;refresh 900 ;retry 900 ;expire 900 ;minimum TTL ) vpn.example.com. IN NS ns.vpn.example.com. ns IN A 192.168.0.2 test IN A 192.168.0.2

    Read the article

  • Failed to open the Parallels networking module

    - by user49204
    I'm running Parallels Desktop 7 on OSX Lion and encounter the issue in the subject on every time I'm trying to launch Parallels VM. The error message contains a hint to restore to network configuration default which does not help. As been advised by some forums to ran the following script: sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_hypervisor.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_hid_hook.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_usb_connect.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_vnic.kext" The output of: sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext" is: Diagnostics for /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext: Warnings: The booter does not recognize symbolic links; confirm these files/directories aren't needed for startup: /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeDirectory /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeRequirements /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeResources /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeSignature Dependency Resolution Failures: No kexts found for these libraries: com.parallels.kext.prl_hypervisor I've noticed that prl_netbridge is not being loaded (when I'm trying to unload it, I'm notified it is not loaded). Am I doing something wrong? What can be the reason for such behaviour?

    Read the article

  • 550 Forged HELO with postfix on debian lenny

    - by Martin Ahrer
    I'm running postfix on a debian lenny system. sending mail in general works without any problems. however some recipent mail systems return an error and I can't get a clue what is causing the problem. So far I suspect that this is either postfix setup itself or the reverse dns resolution. The mail server is running on a virtual server from my service provider. running the command hostname is returning my.domain however running host <ip-address> is returning some alias from the virtual server system. now i'm not quite sure if that is causing my problem???? The mail system <recipient-mail>: host mx0.recipient.domain[xxx.xxx.xxx.xxx] refused to talk to me: 550 Forged HELO: you are not my.domain Reporting-MTA: dns; my.domain X-Postfix-Queue-ID: 6A1135B08002 X-Postfix-Sender: rfc822; [email protected] Arrival-Date: Tue, 13 Apr 2010 17:50:36 +0200 (CEST) Final-Recipient: rfc822; recipient-mail Action: failed Status: 5.0.0 Remote-MTA: dns; mx0.recipient.domain Diagnostic-Code: smtp; 550 Forged HELO: you are not my.domain

    Read the article

  • Is there a reason to use internal DNS over 8.8.8.8 ?

    - by skylarking
    I've inherited a LAN where there is really no name resolution being done for local resources... i.e. all users enter IP addresses manually to access printers and network shares. There are no LDAP servers or domains either....workstations simply connect to the network without authentication. DHCP is handled via a core switch... And DNS settings are also handed out by this same core switch. Currently, the DNS assignments are as such, and in this order: 10.1.1.50 / old Pentium III Windows 2003 box running DNS service- 128 MB RAM 169.200.x.x / ISP 4.2.2.2. / the well known public one There a couple thousand clients on the LAN....and most of the activity is web browsing ( this is an educational setting ). First of all, the server seems woefully underpowered for this task...yet there is virtually no slowness when web surfing by clients.... How much horsepower should a heavily used DNS server have ? I have also heard using 4.2.2.2 is a bad idea .... since it has been so overused... Finally, wouldn't it make sense to have a robust external DNS server listed first? ( Google's 8.8.8.8 would seem to be a logical candidate )

    Read the article

  • SQL Server 2005 - Linked Visual Foxpro Authorization

    - by John
    Here's the Scenario: We have an existing SQL 2000 Server that has a linked server to a share directory (on another server) containing Visual FoxPro tables; all connections work correctly. Porting the SQL 2000 server to a new SQL 2005 server results in questionable behavior: If you connect to the server, remotely, using Windows Authentication, you receive this error when running a query against the linked server: OLE DB provider "MSDASQL" for linked server "[linked server name]" returned message "[Microsoft][ODBC Visual FoxPro Driver]File 'MyTable.dbf' does not exist.". Msg 7350, Level 16, State 2, Line 2 Cannot get the column information from OLE DB provider "MSDASQL" for linked server "[linked server name]". However, logged in locally, the query works fine. The query also works correctly when logged in remotely, but using a SQL login. The only scenario I receive the error is when connected remotely, using windows authentication. As I mentioned before, this works on the SQL 2000 server, and both the old and new servers are running under the same network account (which has access to the folder the FoxPro files are in). Doing a little searching on the internet it looks like others have run into this situation, but I haven't found a resolution. Has anyone run into this before?

    Read the article

  • Repairing Damage to VMWare Virtual Disk

    - by Lachlan McDonald
    Evening all, I've got a considerable problem I'm hoping to get some resolution on. I had two VMWare 6.5 virtual machines, one running Ubuntu 9.10 and the other Ubuntu 10.04. I used 9.10 as a testing server, so I could install a LAMP environment to prepare some code. Over the months I took a number of snapshots of this VM just in case something went wrong, and did a full copy of the entire VM a month ago. I created the 10.04 VM when Lucid Lynx launched so I could continue development on a fresh install. To get the files over, I simply added the 9.10 virtual disk into the 10.04 VM, grabbed some of the files I needed, and dismounted it. Unknown to me at the time, the changes to the 9.04 virtual disk meant that I could no longer boot it with the 9.10 VM. I'd always get the "The parent virtual disk has been modified since the child was created." error. I decided this was a good time to backup all the critical files, but now whenever I open the 9.04 disk to get the data it isn't in the same state as it was earlier. My question is; is it possible when I'm mounting the virtual disk that I'm not seeing the most recent snapshot, or in my blundering, have I lost the virtual disk. Cheers

    Read the article

  • Centos: installing SVN tells I don't have perl 1.17. I have installed 5.8

    - by Emerson
    I'm trying to install SVN on a CentOS virtual machine. I used the command that the CentOS wiki tells: http://wiki.centos.org/HowTos/Subversion yum install mod_dav_svn subversion It gives me a few errors: --> Finished Dependency Resolution mod_dav_svn-1.4.2-4.el5_3.1.i386 from base has depsolving problems --> Missing Dependency: httpd-mmn = 20051115 is needed by package mod_dav_svn-1.4.2-4.el5_3.1.i386 (base) subversion-1.4.2-4.el5_3.1.i386 from base has depsolving problems --> Missing Dependency: perl(URI) >= 1.17 is needed by package subversion-1.4.2-4.el5_3.1.i386 (base) Error: Missing Dependency: perl(URI) >= 1.17 is needed by package subversion-1.4.2-4.el5_3.1.i386 (base) Error: Missing Dependency: httpd-mmn = 20051115 is needed by package mod_dav_svn-1.4.2-4.el5_3.1.i386 (base) The thing is that I have Perl 5.8 installed: root@server [~]# rpm -q perl perl-5.8.8-32.el5_5.2 I also don't know why it tells httpd-mmn isn't installed. I have apache installed for sure. From what I read here, it seems I would need to recompile apache. www.sitepoint.com /forums/showthread.php?t=485683 Any ideas? Update: I also tried to install subversion via WHM (11.28.35) and it gives me the same error. By the way, WHM it says: CENTOS 5.5 i686 virtuozzo on server

    Read the article

  • Tooltips shadow stuck on desktop

    - by faulty
    I tends to get this problem from time to time. The tooltips with a shadow appearing on top of everything. It's the shadow of the tooltips not disappearing after the tooltips disappear. The last one I had the tooltips was from the wifi connection list at the systray. This problem also happen to me on another computer. Both running Win7 with ATI gpu. I found this similar post Menu command stuck on screen but none of the solution helped. In fact the "Fade or slide tooltips into view" has been unchecked from the beginning. Ending task of "dwm.exe" also doesn't help. So far the only way to resolve this by restarting window. I can't post picture yet, so can't show any screenshot. Edit: Just tested a few more trick which doesn't work. 1. Turn of aero 2. Hibernate 3. Switch main display to external display and switch back. 4. Change resolution

    Read the article

  • How to eliminate overscan on Ubuntu HTPC

    - by Norman Ramsey
    I'm using an Ubuntu box with Nvidia graphics card as an HTPC. My HDTV is a Sony Bravia KDS-R50XBR1; this is a rear-projection unit with many inputs. I am using the HDMI input. I'm using the proprietary Nvidia drivers and they recognize the 1080x1920 resolution just fine. The display is a little fuzzy but at 50 inches it's perfect for movies. My problem is that the TV has three overscan settings, and none of them reduces overscan to zero. When I was using dual-screen this was fine, but I'm moving to where the TV is my only screen, and the Gnome panels are not visible because of the overscan. I'd like to figure out how to eliminate the overscan, without trying to scale my 1080p content down to 920p or something ridiculous like that. Ideally there would be some scurvy trick, perhaps involving the TV service menu, to get rid of the overscan on the TV side. Or I could move the Gnome panels, but I still would be missing the edges of my movies. Suggestions most welcome.

    Read the article

  • Why does ATI 5570 HD video card driver installation cause Windows 7 To Blue Screen?

    - by Mort
    This one is for the hive mind. I have a brand new Dell Optiplex 760 workstation with 4 gigabytes of RAM running Windows 7 Professional (32bit). This is a new box with nothing installed other than what was provided for directly by Dell. I installed a Saphire ATI PCI Express 5570 HD. Upon trying to install the 10.4 Catalyst drivers the system will blue screen. It blue screens during the hardware detection phase of the installation process. I have already performed the following trouble shooting steps: Changed system RAM Installed only 2 gigabytes of RAM Installed different versions of Catalyst drivers (10.4 - 9.12) Tried to install video only component of driver (vs entire Catalyst suite) Made sure Windows 7 was fully updated Flashed mother board BIOS to current version Removed and re-seated video card Contacted ATI Support (We all know how this went......) Verified supply outputting properly The blue screen error (via Windows BugCheck entry in event log) is a 0x000000CA and refers to a plug and play error most likely caused by a bad driver. The problem is that the driver installation process never gets far enough to actually install a driver. The resolution center in Windows provides a solution of installing the 10.4 Catalyst driver to resolve issue (which fails). Looking for some alternate views to resolve.

    Read the article

  • Ubuntu 13.10 on Acer V5-472 with HD 4000

    - by Hyperboreus
    I have an Acer V5-472 with intel HD4000 graphics chipset and a built-in 1366*768 display. I have installed ubuntu 13.10 amd64 in legacy boot mode with an external monitor. Installation showed no problems, I can boot from HDD and log into my system. The internal display doesn't work and I have to use an external monitor. I have tried the following (found in other threads) to no avail: Setting grub option "acpi_backlight=vendor" or "acpi_osi=Linux" or both. Installing the intel HD drivers for Linux from their homepage. Running in circles, screaming and shouting. The internal display lights up (I can change the brightness with Fn-Left and Fn-Right) but that's all. When I boot, I get a purple splash screen and from then only the external monitor works. I read somewhere that this might be a problem with kernel 3.11? Has anybody ubuntu running on an Acer V5-472? Should I change ubuntu version or use 32-bit instead? In general, how can I get the internal display to work? Edit: The settings-display dialogue shows the internal display correctly with supported resolution of 1366.

    Read the article

  • Remote Desktop Session Black after Minimize

    - by TorgoGuy
    PROBLEM: When I minimize a remote desktop session and restore it, the remote desktop screen shows up black. This only happens when connecting to a particular computer. DETAILS: If I start clicking around in the black area, portions of the screen will start redrawing and showing up correctly. For example, if I leave a window open in the remote session and click where that window is located on the remote computer, then that window--and only that window--will redraw, and sometimes a portion of that window won't redraw (usually the toolbar). And to clarify--the window only has to be minimized momentarily, so it doesn't seem to be a timeout issue. Clicking or typing in the remote session still causes the remote computer to respond appropriately. Disconnecting from the session and reconnecting restores the whole screen image, as does clicking all over the place in the black image (causing each section to redraw). CONFIGURATION: This problem only happens for me when connecting to a particular computer (a W2K Server box configured to allow remote administration) and only with certain client computers. I've tried 7 different client computers with various versions of Remote Desktop (the OSes were: Win2K, Server 2003, Server 2008, Windows 7 RC, 3 XP) and two of them exhibit the problem (one is one of the XP boxes and the other is Windows 7). Those same computers can RDP to other computers without problem. RESOLUTION ATTEMPTS: I have tried the following: Disable the LOCAL screen saver as mentioned on Technet Turned off bitmap caching in the client, as mentioned on many forums. Updated to version 6.1 of the remote desktop client Using mRemote (I doubted this would work since it uses MS's code for connecting to RDP servers) Turning off all video acceleration. QUESTION: Any ideas on what is causing this?

    Read the article

  • New monitor connected to HDMI adaptor doesn't show output after booting

    - by Paul
    Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you.

    Read the article

  • Providing access to a Samba server for VPN clients

    - by Kamil Kisiel
    We have some Windows users that connect to our network via VPN from home. They need to be able to connect to our Samba server and access a mapped network drive just as they do as when they are on our LAN. The complication is that VPN clients are placed on a subnet other than our office LAN, and behind a firewall. What's the easiest way for me to allow them to still connect to the network share? The solutions I've currently seen involve setting up a WINS server for name resolution purposes and then tunnelling a bunch of the NetBIOS stuff through the firewall. However that means I'd have to set up the VPN DHCP server to hand out the WINS address, something I'm not even sure is possible on the Cisco hardware we have. I'm thinking there must be an easier way. Should I use an LMHOSTS file? Or just map by IP address? Also, I'm not terribly familiar with Windows networking, so which ports would I need to pass through my firewall in order to get the file sharing through?

    Read the article

  • Centos yum install git-sv

    - by bob
    Running yum install on Centos yum install git-svn is producing the following errors: Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * addons: mirror.eshk.hk * base: centos.01link.hk * epel: mirror.bjtu.edu.cn * extras: mirror.eshk.hk * rpmforge: apt.sw.be * updates: mirror.vpshosting.com.hk Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package git-svn.i386 0:1.7.3.4-1.el5.rf set to be updated --> Processing Dependency: perl(SVN::Core) for package: git-svn --> Processing Dependency: perl(Error) for package: git-svn --> Processing Dependency: perl(Term::ReadKey) for package: git-svn --> Running transaction check ---> Package perl-Error.noarch 1:0.17010-1.el5 set to be updated ---> Package perl-TermReadKey.i386 0:2.30-4.el5 set to be updated ---> Package subversion-perl.i386 0:1.4.2-4.el5_3.1 set to be updated --> Processing Dependency: subversion = 1.4.2-4.el5_3.1 for package: subversion-perl --> Finished Dependency Resolution subversion-perl-1.4.2-4.el5_3.1.i386 from base has depsolving problems --> Missing Dependency: subversion = 1.4.2-4.el5_3.1 is needed by package subversion-perl-1.4.2-4.el5_3.1.i386 (base) Error: Missing Dependency: subversion = 1.4.2-4.el5_3.1 is needed by package subversion-perl-1.4.2-4.el5_3.1.i386 (base) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package.

    Read the article

  • Proper 16:9 video size for non-HD 4:3 video (for youtube/vimeo)

    - by Xeoncross
    Since High Definition video came out on all the online sites it has changed the default aspect ratio of the player from 4:3 to 16:9. This means that for people posting SD video you have to resize some of your videos to get them to fit right. For example, NTSC DVD quality (aka 480i/p) is 720x480 pixels (width x height). However, low-end High Definition (720i/p) is 1280x720. Resolution Chart Anyway, now that the video players are built for HD you will find that uploading standard quality videos will result in videos that are "letter boxed" which means they have extra black bars on the top and bottom (or sides). Correct me if I'm wrong, but in order to get a 720x480 video to fit a box that is designed for HD the best practice would be to crop some of it off so that it fits as 720x404 since: 16/9 = 1.78 (1.7777777777778) 720/405 = 1.78 405x1.78 = 720.9 The same would stand for 640x480 (old TV quality) video that would need to be 640x360 correct? I'm asking because I'm not sure about all this and whether this is the proper way to fix these letter-boxing/display problems.

    Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >