Search Results

Search found 5860 results on 235 pages for '8k of power'.

Page 139/235 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

• S.M.A.R.T - Predictive Failure Count

  - by Bastien974

  I'm monitoring my IBM ServeRAID M5015 controller for RAID status with MegaCLI, I have this on one of the disk : Enclosure Device ID: 252 Slot Number: 6 Enclosure position: 0 Device Id: 14 Sequence Number: 2 Media Error Count: 32 Other Error Count: 0 Predictive Failure Count: 18 Last Predictive Failure Event Seq Number: 8119 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.464 GB [0x22cee000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c50042c319c9 SAS Address(1): 0x0 Connected Port Number: 5(path0) Inquiry Data: IBM-ESXSST9300653SS B6336XN04HC10525B633 IBM FRU/CRU: 81Y9671 FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive: Not Certified Drive Temperature :33 Celsius What does this mean exactly ? I can't find an exact description, is there a way to have more details ? The RAID array has the Optimal state. Media Error Count: 32 Predictive Failure Count: 18 Is there a way through the CLI to power-on the front LED so I physically know which disk I need to replace ?

  Read the article

• Asus z53 laptop overheating problem

  - by Tiberiu Hajas

  hi all, wondering if anyone encountered overheating of asus laptop ? especially the z53 model ? usually the right side of the laptop and vent in the upper corner is blowing hot air when under even minimal load, the CPU temperature can easily get to 65-70C and GPU is even above 80C. I'm using NHC (notebook health control) to set to a higher conservatory power consumption but that helps only a bit, anyone opened up the case ? wondering is require a dust clean ...etc ? I still have some warranty on it. thanks

  Read the article

• How to host a scalable social networking app

  - by christopher-mccann

  I am in the middle of developing a social networking application for a very select user niche which could scale to a few million users. Right now I have always hosted applications on RackSpace Cloud and I have no issues with them at all - always been a really good service and never had any downtime. My question is though does anyone think that cloud computing is not the way to host scalable web apps? Or can anyone with experience of this recommend a better solution. I have always shunned trying to run big servers from my own facilities as I think it seems silly to go to the expense of bringing in big alternative power supplies and all the other necessary precautions when other companies already do this. I looked at managed hosting services but this proved to be a bit too expensive for us at the start and the scalability of it wasnt good enough - it would take a day or two to get a new server provisioned. Therefore I ended up on a cloud platform. If anyone has any recommendations or advice it would be greatly appreciated.

  Read the article

• Use QuickCheck by generating primes

  - by Dan

  Background For fun, I'm trying to write a property for quick-check that can test the basic idea behind cryptography with RSA. Choose two distinct primes, p and q. Let N = p*q e is some number relatively prime to (p-1)(q-1) (in practice, e is usually 3 for fast encoding) d is the modular inverse of e modulo (p-1)(q-1) For all x such that 1 < x < N, it is always true that (x^e)^d = x modulo N In other words, x is the "message", raising it to the eth power mod N is the act of "encoding" the message, and raising the encoded message to the dth power mod N is the act of "decoding" it. (The property is also trivially true for x = 1, a case which is its own encryption) Code Here are the methods I have coded up so far: import Test.QuickCheck -- modular exponentiation modExp :: Integral a => a -> a -> a -> a modExp y z n = modExp' (y `mod` n) z `mod` n where modExp' y z | z == 0 = 1 | even z = modExp (y*y) (z `div` 2) n | odd z = (modExp (y*y) (z `div` 2) n) * y -- relatively prime rPrime :: Integral a => a -> a -> Bool rPrime a b = gcd a b == 1 -- multiplicative inverse (modular) mInverse :: Integral a => a -> a -> a mInverse 1 _ = 1 mInverse x y = (n * y + 1) `div` x where n = x - mInverse (y `mod` x) x -- just a quick way to test for primality n `divides` x = x `mod` n == 0 primes = 2:filter isPrime [3..] isPrime x = null . filter (`divides` x) $ takeWhile (\y -> y*y <= x) primes -- the property prop_rsa (p,q,x) = isPrime p && isPrime q && p /= q && x > 1 && x < n && rPrime e t ==> x == (x `powModN` e) `powModN` d where e = 3 n = p*q t = (p-1)*(q-1) d = mInverse e t a `powModN` b = modExp a b n (Thanks, google and random blog, for the implementation of modular multiplicative inverse) Question The problem should be obvious: there are way too many conditions on the property to make it at all usable. Trying to invoke quickCheck prop_rsa in ghci made my terminal hang. So I've poked around the QuickCheck manual a bit, and it says: Properties may take the form forAll <generator> $ \<pattern> -> <property> How do I make a <generator> for prime numbers? Or with the other constraints, so that quickCheck doesn't have to sift through a bunch of failed conditions? Any other general advice (especially regarding QuickCheck) is welcome.

  Read the article

• What type of SATA cable will I buy?

  - by Mehper C. Palavuzlar

  I've bought a new optical drive. It's a Samsung SH-S223C with SATA connection. Since it is OEM with no box, no cable came with it, so I need two cables now. Since I have an extra SATA power cable, it's OK, but I have to buy the data cable. What type of cable should I buy? If you please give a picture of it besides its type as well, I'll be happy. My motherboard is GigaByte P43-ES3G. TIA.

  Read the article

• Adding extra fan on my setup. please advice on proper Exhaust or Intake of Fan.

  - by Pennf0lio

  Hi, I modify my Computer case so that I can add more computer fan to make my computer cool this summer. I would need your thoughts how I can improve my idea and I'm open to all of your advices. Status: Fan Position (The blue circles are the fan's location) At the side I have to intake blowing fresh air at the motherboard and at the top and back I have Exhaust fan blowing out hot air. The computer fans will be powered by 12v adapter (recycled) so that my power supply wouldn't be overloaded. I need a practical advice, I don't want to spend to much on this. Thanks.

  Read the article

• Logging in to a locked computer

  - by Cpt. Jack

  Just recently I have stumbled across an old family laptop that has been out of use for nearly two years. The OS is Windows Vista Home Premium so I'm not quite as enthused about my find as I originally thought I was going to be. However, when I power up the computer it immediately bring me to a login prompt. No one in the family remembers the password it is set to and I am eager to get into this machine. Does anyone know of a way to work around this issue and get into the computer to be able to find out what was configured and saved on it two years ago. Without re-installing the OS I want to bring it back into commission within the family.

  Read the article

• Mac keeps switching to second graphics card

  - by 1.21 gigawatts

  I have a MacBook Pro and whenever I enter certain apps (video camera app or Photoshop for example, the graphics card switched. I didn't know this was going on at first; just that the screen kept changing colors as I opened or closed different software. Later someone told me that the software was causing the OSX to switch graphics cards. It's annoying. How do I keep one graphics card (the better one) enabled all the time? I don't care about power consumption because it is plugged in all the time (though I'm curious how much difference it makes). I just want one graphics card enabled.

  Read the article

• Recover data from a corrupted virtualbox vmdk file?

  - by Neth

  The power went out while I was doing a build on a VirtualBox machine, when I restarted the vmdk for the disk the vm was using was corrupted, apparently irrecoverably. I have been able to grep the 66GB vmdk file and it finds strings from the code I was working on that hadn't gotten in to subversion yet (yeah, yeah I know). But the strings are either in the shell history or what look to be strings inside object files. Any ideas for finding/recovering the source code? If it helps the vm was Linux, Fedora Core 10 on an ext3 filesystem. The host is an ubuntu 10.04_amd64 and has an ext4 filesystem.

  Read the article

• How do I make webmin secure?

  - by Josiah

  I want to install webmin to make server administration tasks on my Ubuntu 10.4 server easier. However I'm very nervious about having that kind of power accessable over the web. So I want to know how to secure webmin so that it can't be used to comprimise my server. So far here are my ideas, but I still don't feel comfortable: Make webmin accessable from only the localhost (how?) Use SSH tunneling to access the webmin server whenever I need to administrate it Can anyone help me with instructions on making webmin accessable only from the localhost? What other ways can I make webmin secure?

  Read the article

• Laptop VGA Out Stopped Working

  - by Jack7890

  I regularly use an external monitor with my laptop. Today, when I booted up, the external monitor refused to work--it just keeps going into power save mode. I tried a different external monitor and had the same problem, so it must be a problem with the laptop itself. Things I've tried: Going into the Display Settings via the Control Panel (I'm running Vista) and attaching/unattaching/reattaching the external monitor. Turning the computer off, unplugging, plugging it back in, and rebooting Blowing into the VGA out to get rid of any dust Toggling through the Fn+F7 options I'm thinking maybe this is an issue with my video card? If necessary, I'm comfortable opening up my laptop and playing around with things, but I'm not sure what to look for. Does anyone have any suggestions?

  Read the article

• Laptop VGA Output Stopped Working

  - by Jack7890

  I regularly use an external monitor with my laptop. Today, when I booted up, the external monitor refused to work--it just keeps going into power save mode. I tried a different external monitor and had the same problem, so it must be a problem with the laptop itself. Things I've tried: Going into the Display Settings via the Control Panel (I'm running Vista) and attaching/unattaching/reattaching the external monitor. Turning the computer off, unplugging, plugging it back in, and rebooting Blowing into the VGA out to get rid of any dust Toggling through the Fn+F7 options I'm thinking maybe this is an issue with my video card? If necessary, I'm comfortable opening up my laptop and playing around with things, but I'm not sure what to look for. Does anyone have any suggestions?

  Read the article

• Click sound from computer when shut down

  - by user32569

  Hi, I build my new computer yesterday and I noticed, when computer is shut down, I mean the exact time its looses power from PSU, relativelly loud CLICK sound occurs. Please does anyone knows from where? I think MB, SSD, VGA, CPU nor coolers are not cousing this. I would guess maybe Samsung 1TB HDD (maybe when heads go back to LZ) or some hard safety switch or relay in PSU? Or just the MB speaker? (Yes, its actually installed). Do you have any experience with this? Thanks.

  Read the article

• Windows 7 setup can not find hard disk

  - by Akshay Kulkarni

  Previously I had an old Seagate barracuda 160GB HDD which got crashed some days before. Yesterday I bought new Hard Disk Seagate Barracuda 500GB (ST500DM002). I just replaced the 500GB hard disk with 160GB one leaving data and power cable intact and untouched. And ideally this new hard disk should start functioning. I tried to install Windows 7 with DVD the setup says you don't have any hard disks installed on your machine. I rechecked connection tried with Win XP setup but continued receiving same error. Do I need to do some initialization stuff with hard disk before installing setup? If so how to do it. If not then is there any problem with my newly bought hard disk? Thanks In Advance.

  Read the article

• Hypertransport sync flood error

  - by Carl B

  What is it? And what causes it? Is it only for uncorrectable DIMM Errors(Troubleshooting DIMM errors)? When an UCE occurs, the memory controller causes an immediate reboot of the system. During reboot, the BIOS checks the Machine Check registers and determines that the previous reboot was due to an UCE, then reports this in POST after the memtest stage: A Hypertransport Sync Flood occurred on last boot 3 BIOS reports this event in the service processor’s system event log (SEL) as shown in the sample IPMItool output There are what seems to be some suggested answers to include Bad Caps Bios verisons (happens in one version not the other) Graphics card issues Lack of power to the CPU The list of possible generators seems to target everything but the computer case. System Specs: Windows Home Premium 64 Motherboard - MSI790FX-GD70 (MS7577) / Bios v 1.9 (American Megatrensa Inc) Ram - Patriot G Series ‘Sector 5’ Edition 4GB DDR3 1600 CPU - AMD Phenom II X2 555 Black Edition Callisto 3.2GHz Socket AM3 80W (Note: unlocked 2 cores CPU Z ids it as phenom II x4 B55) Graphics - 2 x Radeon 5750 in crossfire PSU - ABS 900w HDDs - 2 Seagate 1.5 TB Sata SSD - 1 OCZ 120 GB Vertex Plus R2

  Read the article

• What is the method to reset the Planar 1910m monitor?

  - by Richard J Foster

  My monitor (a Planar, apparently model number PL1910M) is not working. (It is flashing a green / orange sequence which I believe to be an error code. The sequence, in case it helps consists of orange and green three times quickly followed by a longer orange, then another green followed by a long period where both colors appear to be present). I vaguely recall a co-worker suffering from a similar problem, and our IT department "resetting" the monitor by holding down a certain set of keys as they apply power. Unfortunately, I do not remember what that key sequence was, our IT department is not responding, and the Planar web site is blocked by the content filtering firewall we have in place! What is the sequence to perform the reset? (For bonus geek-credit, what does the code mean... as if it indicates a blown component clearly a reset will not help me. ;-))

  Read the article

• Suggestions for Troubleshooting WIndows 7 lockups

  - by Craig L

  I've got a Dell Latitude E6500 that was working fine under Vista x64. I got one of the new Seagate 500GB Hybrid SSD/HD 2.5 drives and thought.. hmm.. let's try Win 7 x64 on it. Bottom line: It works great for hours and then it will hard lock. I don't mean BSOD (or whatever the Win7 equivalent is). I mean my screen is displaying a static image (if there is a clock displayed, it will be frozen at the time the lockup occurred) and the mouse and keyboard do not work. Control-Alt-Delete will not work. I have to hold down the power button to reboot. The event log records NOTHING at the time the lockup occurs. Obviously something is happening to the system to cause the lockup, but the default Windows 7 x64 doesn't log it. How can I log the things Windows doesn't normally log in Event Viewer ?

  Read the article

• Computer froze up

  - by Arlen Beiler

  Why would my computer freeze up out of the blue? I have Apache Webserver w/php, and MySQL server installed. I am not sure exactly when it happened, but I was doing something on a wordpress site that I have installed, and it just waited and waited and waited. Then, all the folders on it that were open on my other computer closed, as though I had disconnected it. Then the skype account went offline. The computer was totally froze. I thought maybe it was someone on logmein, but disconnecting it from the network didn't do anything. I had to "crash" it (held in the power button till it shutdown). It started up normally then and the logs showed absolutely nothing wrong. And doing the same thing that I did when it froze didn't repeat the freeze. Any ideas, I never had this happen before.

  Read the article

• What does "cpuid level" mean?

  - by ogzylz

  For an example, I put just output from 1 core of a 16 core machine. What does the output mean by "cpuid level" of "6"? Also, what do "bogomips" of "5992.10" and "clflush size" of "64" mean? processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 6 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 8 cpu MHz : 2992.689 cache size : 4096 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 fpu : yes fpu_exception: yes cpuid level : 6 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx cid cx16 xtpr lahf_lm bogomips : 5992.10 clflush size : 64 cache_alignment: 128 address sizes: 40 bits physical, 48 bits virtual power management:

  Read the article

• Repair snapped USB flash drive

  - by Richard Slater

  I have a USB Flash Drive that has had the USB connector snapped away from the circuit board. In the past I have had great sucess with soldering the connector back to the circuit board with 4 solid core wires. Unfortunatly this particular device shows up as "Unknown Device" in device manager and displays 0ma power usage. Giving a closer look at the circuit board it appears that the Data + connector has come away from the PCB. Which would explain why it is not recognised. Is there any practicable way of lifting the data from the device? larger version

  Read the article

• SATA hard disk for laptop on Desktop PC

  - by Lawliet

  I know that this forum is for programming-related questions only, but I'm having this dilemma so here I go. Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) Thanks in advance

  Read the article

• Core Animation performance on iphone

  - by nico

  I'm trying to do some animations using Core Animation on the iphone. I'm using CABasicAnimation on CALayer. It's a straight forward animation from a random place at the top of the screen to the bottom of the screen at random speed, I have 30 elements that doing the same animation continuously until another action happens. But the performance on the iPhone 3G is very sluggish when the animations start. The image is only 8k. Is this the right approach? How should I change so it performs better. // image cached somewhere else. CGImageRef imageRef = [[UIImage imageWithContentsOfFile:[[NSBundle mainBundle] pathForResource:name ofType:@"png"]] CGImage]; - (void)animate:(NSTimer *)timer { int startX = round(radom() % 320); float speed = 1 / round(random() % 100 + 2); CALayer *layer = [CALayer layer]; layer.name = @"layer"; layer.contents = imageRef; // cached image layer.frame = CGRectMake(0, 0, CGImageGetWidth(imageRef), CGImageGetHeight(imageRef)); int width = layer.frame.size.width; int height = layer.frame.size.height; layer.frame = CGRectMake(startX, self.view.frame.origin.y, width, height); [effectLayer addSublayer:layer]; CGPoint start = CGPointMake(startX, 0); CGPoint end = CGPointMake(startX, self.view.frame.size.height); float repeatCount = 1e100; CABasicAnimation *animation = [CABasicAnimation animationWithKeyPath:@"position"]; animation.delegate = self; animation.fromValue = [NSValue valueWithCGPoint:start]; animation.toValue = [NSValue valueWithCGPoint:end]; animation.duration = speed; animation.repeatCount = repeatCount; animation.autoreverses = NO; animation.removedOnCompletion = YES; animation.fillMode = kCAFillModeForwards; [layer addAnimation:animation forKey:@"position"]; } The animations are fired off using a NSTimer. animationTimer = [NSTimer timerWithTimeInterval:0.2 target:self selector:@selector(animate:) userInfo:nil repeats:YES]; [[NSRunLoop currentRunLoop] addTimer:animationTimer forMode:NSDefaultRunLoopMode];

  Read the article

• What is the Best Free Linux Gateway

  - by rockinthesixstring

  I'm looking at moving away from using my DIR-825 as a gateway and moving into a Linux box to do it all for me. I've found IPCop, but I'm looking for something with a little more power. My main goal is basically to be able to point different external domain names to different internal servers. backup.example.com - 192.168.0.5 home.example.com - 192.168.0.1 I host my DNS on my own dedicated server (windows), so I don't know much about doing the gateway thing in my home (my hosting provider does it all for me). Do any of you know of any free Linux Distros that can accomplish what I'm looking for?

  Read the article

• upgrading my computer system for office use

  - by denise ellul

  Presently I have the under-mentioned computer system. What should be changed and upgraded with the following products that I own presently? I am interested in performance issues related to cache memory, bus speed, RAM, CAS latency as well as other considerations. Thanks for your help. Processor (CPU): Intel Celeron Dual Core E3300 2.5 GHz Motherboard: Asus P5QPL-AM G41 Main Memory (RAM): 2 GB Team Elite DDR2 PC8000 Case: Coolermaster RC330 Power Supply Unit: 500W EZ-Cool Standard Storage Device (Hard Drive): 500GB Samsung Video Card: Intel GMA X4500 (On-board) Optical Drive: LG GH22NS50 Sound Card: AC 97 (On – board) Card Reader: Akasa Black TFT Monitor: 19” View Sonic Speakers: Logitech S120 2.0

  Read the article

• Dell U271 monitor DisplayPort suddenly not working

  - by Amir Latif

  My new(ish) Dell U271 took a bit of a knock and it now suddenly doesn't recognise the Macbook plugged into it via DisplayPort - this had been working great for several months up until now. When I "Scan Sources", it doesn't find anything on DisplayPort. However, one suspicious behaviour leads me to think all might not be lost. When the Mac is woken from sleep, this used to kick the monitor in (as an monitor would) and while it no longer does that, the light on the monitor does go from standby orange to blue briefly, then the monitor says it's going into "power save" mode. It seems like it gets some kinda signal. Any ideas on how I can diagnose the problem? I'm trying to find another mac but no one near me has one ...

  Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >