Search Results

Search found 448 results on 18 pages for 'reconnect'.

Page 14/18 | < Previous Page | 10 11 12 13 14 15 16 17 18  | Next Page >

  • Active RDP session over VPN getting disconnected

    - by Wandering Penguin
    I am having seemingly random disconnects of active RDP sessions (I am actively typing or otherwise interacting with the desktop) when connected over the VPN connection. The attempted to reconnect 1/20 pops up and proceeds all the way through 20 then drops. Once the session drops I can open a new session and connect again. This started happening about a week ago, The VPN connection is an IPSec VPN connection from a SonicWall NSA 2400. The NIC drivers are up to date. The VPN client is up to date. The firmware on the SonicWall is up to date (both regular and the early-release versions work the same). I have attempted to connect over three ISPs all with the same behavior. Two different workstations were used to test the VPN connection. The same behavior occurs when connecting to a domain workstation or server. If I am within the firewall I can connect to the same workstations and servers with the disconnect. The VPN connection has "enable fragmented packet handling" and "ignore DF (don't fragment) bit" set. Is there something I am missing in where I am looking for the problem?

    Read the article

  • Application losing Printer within Terminal Services for remote users

    - by Richard
    Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

    Read the article

  • How do I fix libdispatch problem crashing Mac OS X apps?

    - by david-ocallaghan
    In the last day I have started having a lot of brokenness on my Mac (MacBook Air running Mac OS X 10.6.2 with all software updates). Most noticably, iTunes no longer syncs with my iPhone. It fails with a crash dialog reporting "AppleMobileDeviceHelper quit unexpectedly" and an error dialog "iTunes was unable to load dataclass information from SyncServices. Reconnect or try again later." I've attempted the fix at support.apple.com/kb/HT1747 but it failed. I've also been having problems (at first seemingly unrelated) with the horrible Cisco VPN client, which started giving me this error: Error 51: Unable to communicate with the VPN subsystem I followed the steps at www.anders.com/cms/192/CiscoVPN/Error.51:.Unable.to.communicate.with.the.VPN.subsystem which don't seem to work for me, although I can connect if I use the command line with sudo : sudo vpnclient connect MyProfile I had a look in the Console app at the diagnostic messages and I noticed a pattern, that a number of apps were reporting "BUG IN CLIENT OF LIBDISPATCH". The affected programs are: AppleMobileBackup AppleMobileDeviceHelper Safari Webpage Preview Fetcher cvpnd (the Cisco VPN daemon) Of these, only the last is non-Apple software! The common text in the diagnostic messages is: Exception Type: EXC_BAD_INSTRUCTION (SIGILL) Exception Codes: 0x0000000000000001, 0x0000000000000000 Crashed Thread: 1 Dispatch queue: com.apple.libdispatch-manager Application Specific Information: BUG IN CLIENT OF LIBDISPATCH: Do not close random Unix descriptors I'm beginning to wonder if there's a permissions problem, or corruption of an important library, ... I should note that I've rebooted several times and verified the disk permissions and the disk. Any help would be great!

    Read the article

  • Persistent static route stops working after VPN drops and reconnects

    - by user76157
    I've got a VPN between two networks, one home and one office (A and B). Their subnets are: (A) 192.168.1.0 and (B) 192.168.0.0 The two networks have identical ADSL routers. Unfortunately these can only do dial-out VPN. So I've got a Windows 2008 server on Network B acting as a VPN server (ServerB). Network A's router (RouterA) passes through Network B's router and connects via PPTP to ServerB. RouterA is assigned the static IP 192.168.0.40 on Network B. There's a persistent static route on ServerB telling it to use 0.40 for all requests to Network A's subnet, 192.168.1.0. (route -p add 192.168.1.0 mask 255.255.255.0 192.168.0.40). This enables ServerB to ping all machines on A (and those machines to ping ServerB). The VPN connection occasionally drops (I'm not sure why - it's set to remain always on and seems to drop randomly). This wouldn't be too much of a problem, as it reconnects automatically and quickly, except that when it does reconnect, the static route on ServerB no longer works. Route print (on ServerB) shows that the persistent static route still exists. However a tracert to a machine on Network A doesn't use the static route; it tries instead to use ServerB's default gateway (which is RouterB), and fails to find the machine. Deleting and re-adding the static route fixes the problem - a tracert uses the static route. At the moment, a batch file to delete and re-add the static route is scheduled to run every day. But this is clearly far from an ideal solution! I hope that's not too confusing. Any help would be very much appreciated.

    Read the article

  • o2cb thinks ocfs2 cluster is still online, and refuses to shut down

    - by Kendall
    I have a handful of OpenSuSE 11.2 servers that utilize OCFS2 volumes. I've noticed that o2cb can't figure out when the OCFS2 cluster is actually mounted. For example, when I try to shutdown o2cb, after stopping OCSF2, o2cb refuses to shutdown because it thinks OCFS2 is still up! After stopping OCFS2 I try to stop o2cb... hamguy:/dev/disk/by-label # /etc/init.d/o2cb stop Stopping O2CB cluster ocfs2: Failed Unable to stop cluster as heartbeat region still active So I check the status... hamguy:/dev/disk/by-label # /etc/init.d/o2cb status Driver for "configfs": Loaded Filesystem "configfs": Mounted Stack glue driver: Loaded Stack plugin "o2cb": Loaded Driver for "ocfs2_dlmfs": Loaded Filesystem "ocfs2_dlmfs": Mounted Checking O2CB cluster ocfs2: Online Heartbeat dead threshold = 31 Network idle timeout: 30000 Network keepalive delay: 2000 Network reconnect delay: 2000 Checking O2CB heartbeat: Active And double check OCFS2... hamguy:/dev/disk/by-label # /etc/init.d/ocfs2 status Configured OCFS2 mountpoints: /u/conf /u/logs /u/backup /u/client /u/data /u/mdata OCFS2 is clearly down, while o2cb clearly thinks otherwise. The versions of OCFS2 and o2cb are... kendall@hamguy:~> rpm -qa |grep ocfs2 ocfs2console-1.4.1-25.6.x86_64 ocfs2-tools-o2cb-1.4.1-25.6.x86_64 ocfs2-tools-1.4.1-25.6.x86_64 kendall@hamguy:~> rpm -qa |grep o2cb ocfs2-tools-o2cb-1.4.1-25.6.x86_64 What causes this, and is there a way around it? If I try to reboot the machine, it will just sit there forever until your physically power cycle it. That obviously is a bit of a problem. Any insight is appreciated, thank you. Kendall

    Read the article

  • Possible DNS issue?

    - by durilai
    I am having an issue, which I think stems from DNS. I have 2 servers. Server 1 is AD server with DNS, which was automatically configured when installing AD. The second server is a web server that is part of the domain, but it is not AD nor any other role. I can remote desktop in from server 1 using internal IP address, but when I attempt to connect from any other computer it fails, the computer can connect to server 1. I am able to ping both servers, as well as nslookup both using their FQDN. I am also able to telnet to port 3389. Any help is appreciated UPDATE I do not think it is DNS anymore, but not sure what it is. The remote desktop connects and I get to the login prompt, but when I start to enter credentials it disconnects. I then am unable to reconnect. If I wait for about 10 minutes it will allow me to repeat, but with the same results. UGH!!!

    Read the article

  • Application losing Printer within Terminal Services for remote users

    - by Richard
    Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

    Read the article

  • Diagnosing linux issues with ipod syncing in Ubuntu

    - by alexpotato
    Issue: I am currently using Ubuntu 9.10 with a 5th generation Ipod 60 GB Black video classic. In general, it seems that Ubuntu can always detect the usb hd and displays it on my desktop. However, some applications seem to detect the ipod (e.g. Rythymbox and gtkpod do but Banshee does not) and some don't. I narrowed down the banshee issue to a bug that requires Nautilus to be restarted (although it would be nice to not have to do this). Also, Whenever I sync between these applications, it appears that everything is working fine during the sync but when I disconnect the ipod and browse, all of the songs seem to be there but the playlists are not. If I reconnect the ipod, in banshee specifically it sees the space usage as "other". What I am looking for is some way to at least understand what is and is not working OR directions to some where that can help me learn what's going on. I have already tried: -IRC. Either the channel is too general (e.g. #ubuntu) or no one is ever one (e.g. #banshee) -The web. Most of what I've found is too specific to one particular bug or too general. Any thoughts?

    Read the article

  • How to re-join an AD2003 domain with Samba after deleting the machine account?

    - by Guss
    During some troubleshooting I deleted the machine account for a Linux server running samba from our AD 2003 domain. We are using Kerberos for authentication, and after I deleted the machine account I tried to join the domain again using net ads join -U Administrator But I keep getting Kerberos errors like these: [2009/08/18 16:14:36, 0] libads/kerberos.c:ads_kinit_password(228) kerberos_kinit_password [email protected] failed: Client not found in Kerberos database Failed to join domain: Improperly formed account name It appears as if samba remembers that it once had an account with the AD and keeps trying to reconnect to it, but I want to create a new account from scratch. I tried to delete all the .tdb files I could find as well as everything under /var/cache/samba but to no avail - it still behaves the same. I also tried to create the machine account on the AD side, but then I get a similar error when I try to join, about failure to authenticate with the machine account - it looks like samba tries the previous machine account password and I don't know how to reset it, or even if I could figure out what samba uses - how to set it in the AD. Any help would be greatly appreciated, as at this point the only thing I can think about is to reformat and reinstall the machine, and I would really REALLY love to not do that. Thanks in advance.

    Read the article

  • Drive Mapped On Amazon EC2 Instance Startup Disconnected After Logon

    - by jsn
    I am launching an Amazon EC2 instance (Windows Server 2012), and on startup (though User Data field), it runs this powershell script: <powershell> NET CONFIG SERVER /AUTODISCONNECT:-1 # clear all prior connections net use * /delete /y > C:\delLog.txt 2>&1 # mount new drive net use R: \\dbHost\share /user:username pass /persistent:yes > C:\useLog.txt 2>&1 ipconfig /all > C:\ipLog.txt </powershell> When it launches and I connect to it through RDP, it shows in explorer "Diconnected Network Drive (R:). If I double click it, error message displays "R:\ is not accesible. Access id denied". Normally, it would ask me for credentials to reconnect. I need for this drive to be connected through the duration of the instance. delLog.txt contents: You have these remote connections: T: \\dbHost\share Continuing will cancel the connections. The command completed successfully. useLog.txt contents: The command completed successfully. ipLog.txt contents as expected. The net use commands works fine by itself, it connects. Anyone have any idea what could be wrong? There is only one account on these machines - Administrator. It is a samba share to a Linux server on a private network.

    Read the article

  • Coldfusion 9 losing connection to MySQL 5 database server a couple of weeks after the server is started

    - by user1503757
    We get the following Coldfusion error message after our server have been running for a couple of weeks: Error Executing Database Query.Could not create connection to database server. Attempted reconnect 3 times We run Coldfusion Enterprise 9 on a one year old XServer with Snow Leopard and MySQL 5 The server has about ten DSN set up in the Coldfusion Administrator All local, with default advanced settings, and host set to "localhost" The server is not under heavy load. The strange thing is that after a restart of the server, everything works fine. Then after a week or so, some databases will stop working, in the sense that Coldfusion cannot create a connection to them. If I then go to the Coldfusion Administrator and click "Verify all datasources", I will get that only 2 or 3 got verified, the other ones failed, and it is always the same datasources that can't be verified when the server starts to behave like this if I try to verify again, BUT NOT neccessary the same datasources that couldn't be verified the last time the server behaved like this. I know about the setting "max_connections" and we have included a line for that setting in the MySQL config file and set it to 2000, and when we read it by a query it says "2000", so that can't be the problem. Anyone?

    Read the article

  • Replacing stock Core 2 Duo heatsink fan (just the fan really) with a Dell CPU fan

    - by user647345
    My old heatsink fan broke and I'm trying to reconnect its plugs to a new fan. My Dell CPU fan has some custom Dell plug. I snipped the old fan's wire in half and kept the plug on the end of it. I want to connect it to the Dell fan wire to the plug. The motherboard is a P5Q-e, the stock Core 2 Duo fan was .20A and the dell is .70A. Is that going to matter? The wire from the fan has four wires, the wire with the plug has four wires. They share three, of the four colors: red, black, and blue. Dell's fourth wire is white, while the plug's fourth wire is yellow. Is it safe to assume that I just connect the yellow and the white plug together and match the rest up? I don't want to take any risk of damaging anything. It runs fine passively without a fan, but I have speedstep on, so I would like to use this fan and just fasten it to the heatsink with some twist ties and paperclips and call it a day.

    Read the article

  • Internet slowed down because of SQUID Server setup

    - by Ranjith Kumar
    Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

    Read the article

  • Remote Desktop Network Level Authentication Not Supported

    - by Iszi
    I'm running Windows XP Professional SP3 x86, trying to connect to a system with Windows 7 Ultimate SP1 x64. Recently, I updated the Remote Desktop Connection software on the XP system in hopes of using Network Level Authentication (NLA) for my connections to the Windows 7 box. After the update, I connected to the Windows 7 box over RDP and enabled NLA believing that the updated client should support it. After disconnecting and attempting to reconnect, I'm presented with the following error: The remote computer requires Network Level Authentication, which your computer does not support. For assistance, contact your system administrator or technical support. So, I checked the About page in Remote Desktop Connection to make sure the update had applied. This is what I see. Remote Desktop Connection Shell Version 6.1.7600 Control Version 6.1.7600 © 2007 Microsoft Corporation. All rights reserved. Network Level Authentication not supported. Remote Desktop Protocol 7.0 supported. I thought NLA was supposed to be a part of RDP 7.0 clients. Is there a component I'm missing somewhere?

    Read the article

  • Problem IIS 7.0 Locking files durring upload

    - by viscious
    I am running a server 2008 with iis7 and the ftp addon on to iis 7.0 I have the ftp site configured and mostly working Except that about 70% of the time when transferring a file the upload will hang forever. If I disconnect the ftp client and reconnect and try to upload the same file I will get an error on the client saying the file is locked. I have to restart the ftp service to clear the lock. I fired up process explorer and did a search on the file in question and sure enough the ftp service has a lock on the file and it takes around 20 minutes to release the lock on its own (and sometimes longer). This lock stays around even after I disconnect the client. Like I said this only happens about 70% of the time, the other 30% of the time it goes through just fine. Things i have verified. -Not a firewall issue. Server is using passive port range 8000-9000 which is allowed on the firewall. -Not a nat issue, server has a globally rout-able ip address -all recommended/required updates installed I have 5 other servers in a very similar configuration and this is the only one i have problems with.

    Read the article

  • VMWare Host Not Responding - VMs are Disconnected (ESXi 3.5)

    - by EyeonTech
    I have inherited a VMWare environement ESX v3i 3.5. I am not fluent with VMWare ESXi so bare with me. Two days ago, when I opened Virtual Centre, one of the Hosts showed up as Not Responding. The error I am seeing is:----- Unable to acquire licenses because license source is unavailable: The license manager has not been started yet, the wrong port@host or license file is being used, or the port or hostname in the license file has been changed. What I have tried: I have Stopped and Started the license server within the application. When I do this, I am able to disconnect the host in Virtual Centre and reconnect. This brings the host back online, but a few minutes later, the host goes to a not responding state again. I have rebooted the server with the Licensing software installed. While browsing Google, I have not been able to find any steps I feel comfortable performing and I would like the opinion of the VMWare pros. Where are the log files I should be looking at to correctly determine what is going on? Has anyone seen this behaviour and how did you resolve it? Thank you

    Read the article

  • Why do my Xcode default font starts to look ugly after some time, until I restart?

    - by mystify
    I plugged in an external monitor. All resolutions match perfectly. MacBookPro LCD is closed. After restarting Xcode editor fonts look very bad. Only in Xcode. When I restart the mac and DON'T use an external monitor, fonts look all right again. When I attach the monitor and close the LCD of the MacBookPro, fonts look nice. Then I close Xcode and reopen it: Fonts suck. Only way to get fonts look good is to disconnect external monitor and reboot, then reconnect external monitor, close LCD, wait, hit any key and let the external monitor be the only one. Fonts look nice - until I restart Xcode. I think it happens any time Xcode is launched with external monitor attached and ugly fonts survive until reboot. Unplugging external monitor and restarting Xcode doesn't help. It seems like Xcode isn't antialiasing them properly after something happens. Is there a fix for this problem? EDIT: After trying a few more times, it seems it is possible to get fonts to look nice by disconnecting external monitor and reopening xcode. Here are some little snapshots: GOOD FONT: UGLY FONT: You can see how dirty the ugly font looks. It's very hard to read and hurts in the eyes. Believe me. It sucks. Sometimes the little "i" are almost invisible. I make use of the very eye-friendly Dusk style of Xcode (go to preferences and choose that, if you haven't already. A real pleasure for your eyes)

    Read the article

  • Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

    - by Nick
    I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

    Read the article

  • Nexus One WiFi connection problems.

    - by sunocky
    I have two new Nexus One for a research project. For the projects I need to keep a server running on the phone. But soon I found out that both the phones have inconsistent WiFi connection problems at my home. It can connect to my WiFi network, but will drop off in a random time. And in order to reconnect to my WiFi, I may need to reboot my router, or the phone will say "obtaining IP address" and then "Unsuccessful". I also own a G1 with firmware version 1.6, it has no such connection problems. Well, to my surprise, the two Nexus One works fine with connecting to the WiFi network at my work place, which is a WEP type WiFi connection. By the way, it is a WPA type connection at my home. Anyone knows what's the problems with the Nexus One? Any suggestions on what should I do if I want to keep the WiFi connection live all the time at my home? Thanks very much!

    Read the article

  • RDP or SSH connection trough Windows 2008 server VPN hang after a while

    - by xt4fs
    I have been experiencing a very strange issue with our VPN setup on Windows Server 2008. That server is running as a Xen Virtual Machine. We use it for two purposes, permit our mobile workers to connect to another server hosted somewhere else that only allow that ip, and use it to RDP or ssh to many other virtual machine on the same server. The server has no performance issue and still a load of memory free. All other virtual machine has no problem whatsoever. Many of those virtual machine have public IP (web servers) and all their firewall are set to allow only ssh connection or RDP connection from their local interface. When I am connecting directly with either ssh or RDP to one of the other virtual machine everything run without any issues. However, when I am doing so through the VPN after some time the connection just hang, it usually continue after some time (5 or 10 minutes). It seems as more there is network usage more often it happen to a point where it is completely unusable. The worst thing I can do to hang it faster is to actually ping the vpn client IP from the local network, after some time the latency increase until it hang. This happen even if I do RDP to the local ip of the VPN server trough the VPN. The server report no problem and if I disconnect to the vpn and reconnect right away everything is alright. There is nothing wrong in the VPN server log. I have taught at the beginning that it could have been an issue with the Host server so I try to RDP,ssh directly to the guest and I have experience no issue while doing this, so it really seems to be a problem with the VPN server on Windows server 2008. Another very weird thing is it does not seems to be of any issue if you only do Internet (NAT) without trying to connect to any local ips.

    Read the article

  • Some process/service/driver repeatedly presses F5

    - by VitalyB
    Hi everyone, I have the strangest problem that started 2 days ago (Windows7, 64bit). SOMETHING causes my F5 key to be constantly pressed. Rebooting helps, but only for a while, it keeps coming back to that. So far I've tried to disconnect and reconnect the keyboard (physically), however, disconnecting the keyboard doesn't actually do anything. Reconnecting it back again, causes the F5-pressing to stop, but not for very long (seconds/minutes). I'd really like to avoid a binary search for the programs (process closing/keyboard switching/etc) before I can, at the very least, identify the source of the keypress. Is there an application that can show me what is causing a key press? E.g is it the keyboard driver, or some process that executes SendKey repeatedly for reasons unknown. Thanks! P.S FYI, having F5 causes the strangest side effects. Task Manager refreshes very very quickly (as F5 is refresh), the desktop is constantly flickering and all the browsers stop working as they keep trying to refresh. I was lucky to find out what the heck is happening only because I started notepad and saw that current date/time started to appear constantly. If not that, I'd still be wondering.

    Read the article

  • Expired password change through VPN failure

    - by Tim Alexander
    I am setting up some new accounts to be used by some contractors. they are going to connect via VPN to our network. My requirement is to set the password initially and then have them change it the first time they log in. As a result the "User must Change Password" box is checked. Loading up a laptop and testing has yielded poor results. When logging in I get a notification that the password has expired and a box to fill in, which I do. it then appears again so I dutifully fill in the password details again. I am then presented with a "Sending Password...." error box with Error:619 listed as the reason. Trying to reconnect then gives a 691 error that the password is bad. From the firewall, that is the actualy VPN server, I can see RAD_ACCESS_DENIED and from the DC running NPS (acting as a RADIUS server for the firewall with MS-CHAP-v2 enabled with the "User can change password after it has expired" checked) I cannot see a request to change the password. I can only see Event ID 4776, 4625 and 6273 (reason 16). I can log in with out the change password flag fine so I know logins are being authenticated. Really hoping someone might be able to assist in tracking down the lack of password change processin gon the DC.

    Read the article

  • Domain Controller died, now get authentication boxes in IE for SDL Tridion 2009

    - by Rob Stevenson-Leggett
    We had a major network issue where our secondary domain controller (responsible for Win2k3 boxes) died and had to be rebuilt (I beleive this is what happened, I am a developer not network admin). Anyway, I am working remotely via VPN at the moment and since this happened, I am getting an authentication box when trying to access certain areas of SDL Tridion via IE (Tridion 2009 SP1 is IE only) it seems like somewhere my credentials are not being passed correctly or the ones cached on my laptop do not match the ones the Domain Controller has. This only seems to affect Windows 2003 servers. Our IT support thinks that the only way to sort it out is to connect my laptop directly to the network. I am not planned to go to the office for a few weeks at least and this issue means I have to work with Tridion via Remote Desktop. We thought changing the password on my account might work but this didn't help. So basically my question is, is there any way I can reset my credential cache without having to reconnect to the network? Or is it IE that is causing the problem perhaps, since I can RDP to servers and use Tridion 2011 instances in other browsers fine? I am on Windows 7 using SonicWall VPN client.

    Read the article

  • SSH sometimes screws up connection when terminal overflows?

    - by SeveQ
    I've got a problem with SSH on a Debian Lenny based server (it's a vHost within a Xen environment, booted on a Xen kernel). I hope someone can help me with this. The SSH connection seems somehow getting screwed up frequently when the terminal overflows (new lines beyond the bottom of the terminal, usually forcing it to scroll). The connection gets lost but not regularly disconnected. It nearly always happens when I do the following: an existing SSH connection gets disconnected (regularly) I order putty to reestablish the connection login-prompt appears at the very bottom of the putty terminal window I enter my login-name, press the enter key I'm asked for the password, I enter it, press the enter key and BOOM! Nothing more happens. I have to reconnect again. So it is reproducable. I'm not totally sure if the connection crashes before or after I enter the password. Furthermore it also happens when there is much text to be displayed (for example when I compile something or do an ls -l on a directory with many entries). Using 'screen', however, helps to reduces the frequency of occurence but doesn't solve the problem completely. It's occurence is independent from which terminal software I use. I mostly use putty but it also happens with other clients. I certainly hope somebody can help me solving this problem. Thanks in advance! //edit: I've just made a Wireshark trace of the ssh connection and there is nothing, I repeat, nothing different between the working and the failing connection (at least aside from frame numbers, ports and times that obviously can't be equal). This leads me to the assumption that the error has to happen on the server's side.

    Read the article

  • Periodic internet connection drops

    - by sterlingholt
    My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

    Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18  | Next Page >