Search Results

Search found 5122 results on 205 pages for 'max'.

Page 148/205 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

• Fans running very fast on MacBook Pro 8.1 ubuntu 12.04

  - by Tomasz Kacprzak

  I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

  Read the article

• Fans running very fast on MacBook Pro 8.1

  - by Tomasz Kacprzak

  I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

  Read the article

• [EF + Oracle] Inserting Data (Sequences) (2/2)

  - by JTorrecilla

  Prologue In the previous chapter we have see how to create DB records with EF, now we are going to Some Questions about Oracle.   ORACLE One characteristic from SQL Server that differs from Oracle is “Identity”. To all that has not worked with SQL Server, this property, that applies to Integer Columns, lets indicate that there is auto increment columns, by that way it will be filled automatically, without writing it on the insert statement. In EF with SQL Server, the properties whose match with Identity columns, will be filled after invoking SaveChanges method. In Oracle DB, there is no Identity Property, but there is something similar. Sequences Sequences are DB objects, that allow to create auto increment, but there are not related directly to a Table. The syntax is as follows: name, min value, max value and begin value. 1: CREATE SEQUENCE nombre_secuencia 2: INCREMENT BY numero_incremento 3: START WITH numero_por_el_que_empezara 4: MAXVALUE valor_maximo | NOMAXVALUE 5: MINVALUE valor_minimo | NOMINVALUE 6: CYCLE | NOCYCLE 7: ORDER | NOORDER 8:    How to get sequence value? To obtain the next val from the sequence: 1: SELECT nb_secuencia.Nextval 2: From Dual Due to there is no direct way to indicate that a column is related to a sequence, there is several ways to imitate the behavior: Use a Trigger (DB), Use Stored Procedures or Functions(…) or my particularly option. EF model, only, imports Table Objects, Stored Procedures or Functions, but not sequences. By that, I decide to create my own extension Method to invoke Next Val from a sequence: 1: public static class EFSequence 2: { 3: public static int GetNextValue(this ObjectContext contexto, string SequenceName) 4: { 5: string Connection = ConfigurationManager.ConnectionStrings["JTorrecillaEntities2"].ConnectionString; 6: Connection=Connection.Substring(Connection.IndexOf(@"connection string=")+19); 7: Connection = Connection.Remove(Connection.Length - 1, 1); 8: using (IDbConnection con = new Oracle.DataAccess.Client.OracleConnection(Connection)) 9: { 10: using (IDbCommand cmd = con.CreateCommand()) 11: { 12: con.Open(); 13: cmd.CommandText = String.Format("Select {0}.nextval from DUAL", SequenceName); 14: return Convert.ToInt32(cmd.ExecuteScalar()); 15: } 16: } 17:  18: } 19: } This Object Context’s extension method are going to invoke a query with the Sequence indicated by parameter. It takes the connection strings from the App settings, removing the meta data, that was created by VS when generated the EF model. And then, returns the next value from the Sequence. The next value of a Sequence is unique, by that, when some concurrent users are going to create records in the DB using the sequence will not get duplicates. This is my own implementation, I know that it could be several ways to do and better ways. If I find any other way, I promise to post it. To use the example is needed to add a reference to the Oracle (ODP.NET) dll.

  Read the article

• Advice on how to build html5 basic tile game (multi player, cross device)

  - by Eric

  I just read http://buildnewgames.com/real-time-multiplayer/ which explains the fundamentals and bets practices to build a massive real time multiplayer html5 game. My question is however given the “simplicity” of the game I need to build (simple kind of scratch game where you find or not something behind a tile), do I really need complex tools (canvas or node.js for example) ? The game The gamestakes place with a picture of our office as a background (tilemap). For HR purpose, we wish to create the following game fore employees: each day they can come to the website and click on a certain number of tiles (3 max per day) and find behind it motivation advice and interesting facts about the company. The constraints and rules the screen is divided into isometric 2D square tiles. There are basically an image (photograph of our office) number of tiles on the screen game: about 10,000 to much more (with scroll , see below) the players can scroll in 4 directions there are only 2 types of tiles: already open and closed player can open tiles that have not been yet open by other players there is no path for players : any player can click on any tile on the screen at any moment (if it’s not already done by another player) 2 players can’t be on the same tile at the same moment (or if they can, I’ll have to manage to see which one clicked on it first) only one type of player (all with similar roles), no weapon, no internal score… very simple game. no complex physics (collision only occurs if 2 players are on the same tile) The target I need to achieve: cross device, cross browsers high performance reaction (subsecond reactions) average nb of players per hour: up to 10K players per hour (quite high indeed but it’s because we aim at proving our case for the game to our business unit) So what I would like to know: 2D Tiled map: Do I need tiledmapeditor or can I enable me split the screen like here ? should I use canvas or plain html/css could be sufficient for my need? do I need a game engine/framework such as melon.js or crafty./js ? (even if the game play is extremely basic, I do need mouse and touché device support, mouse emulations on touch devices…) or ca I easily/quickly do it without? for my constraints and targets, should I use CPU acceleration ? for my constraints and targets, should I use web workers ? for the database, for a massively real time game should I avoid to put the current locations of player in MySQL as i feel it might slow me down. What kind of DB should I implement ? Thanks for your help !

  Read the article

• PXE boot linux. PXE-E51: No DHCP or proxyDHCP offers were received

  - by athspk

  I am trying to have an ubuntu box (192.168.10.9) acting as a PXE server, but i have trouble getting DHCP to work. The PXE server is connected to a SOHO router (192.168.10.1) acting as a switch. I have disabled the DHCP server on the router. $ dhcpd --version isc-dhcpd-4.2.4 The contents of /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name-servers 192.168.10.1; default-lease-time 3600; max-lease-time 7200; authoritative; log-facility local7; allow booting; allow bootp; subnet 192.168.10.0 netmask 255.255.255.0 { range dynamic-bootp 192.168.10.101 192.168.10.200; option routers 192.168.10.1; option broadcast-address 192.168.10.255; next-server 192.168.10.9; filename "/tftpboot/pxelinux.0"; } The contents of /etc/default/isc-dhcp-server INTERFACES="eth0" When the client boots, it tries to get an IP address from the server but fails with the following Error message: PXE-E51: No DHCP or proxyDHCP offers were received. On Server side, i was tailing /var/log/syslog while the client tries to boot: Dec 4 12:57:10 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:11 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:12 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:12 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:17 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:17 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:25 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:25 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Please advise. Thanks in advance

  Read the article

• ignoring informational payload, type INVALID_COOKIE msgid=00000000

  - by user197279

  I'm configuring a site-to-site vpn between openswan ipsec and cisco asa 5540. After the step, i started ipesc service but the error i'm seeing is: ignoring informational payload, type INVALID_COOKIE msgid=00000000 Nov 5 09:42:30 pluto[11712]: "myVPN" #1: received and ignored informational message Nov 5 09:42:51 pluto[11712]: "myVPN" #1: ignoring informational payload, type INVALID_COOKIE msgid=00000000 Nov 5 09:42:51 pluto[11712]: "myVPN" #1: received and ignored informational message Nov 5 09:43:30 pluto[11712]: "myVPN" #1: max number of retransmissions (2) reached STATE_MAIN_I2 Nov 5 09:43:30 pluto[11712]: "myVPN" #1: starting keying attempt 2 of at most 3 Any advise why I'm getting this error on openswan? Also sudo ipsec whack --status gives: "myVPN": 10.0.xx.0/24===10.0.7x.x[54.209.y.yyy,+S=C]---10.0.xx.x...10.0.70.x---41.22x.4.xx<41.22x.4.xx[+S=C]===41.22y.4.yyy/32; unrouted; eroute owner: #0 000 "myVPN": myip=54.209.zz.zz; hisip=unset; 000 "myVPN": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 3 000 "myVPN": policy: PSK+ENCRYPT+TUNNEL+DONTREKEY+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,32; interface: eth0; 000 "myVPN": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 "myVPN": IKE algorithms wanted: AES_CBC(7)_256-SHA1(2)_000-MODP1024(2); flags=-strict 000 "myVPN": IKE algorithms found: AES_CBC(7)_256-SHA1(2)_160-MODP1024(2) 000 "myVPN": ESP algorithms wanted: AES(12)_256-SHA1(2)_000; flags=-strict 000 "myVPN": ESP algorithms loaded: AES(12)_256-SHA1(2)_160 000 000 #5: "myVPN":500 STATE_MAIN_I2 (sent MI2, expecting MR2); EVENT_RETRANSMIT in 8s; nodpd; idle; import:admin initiate 000 #5: pending Phase 2 for "myVPN" replacing #0 Thanks.

  Read the article

• Juniper EX3300 routing issue

  - by Richard Whitman

  The routing on my Juniper EX3300 does not seem to be working. My ISP's gateway is at xx.xx.xx.xx. And I have the following in the configuration: routing-options { static { route 0.0.0.0/0 { next-hop xx.xx.xx.xx; retain; } } } I can ping to my ISP's gateway from the switch. However, I can NOT ping to any other IP. When I do a traceroute (to Google.com's IP). This is what I get: traceroute to 74.125.224.69 (74.125.224.69), 30 hops max, 40 byte packets traceroute: sendto: No route to host 1 traceroute: wrote 74.125.224.69 40 chars, ret=-1 *traceroute: sendto: No route to host Do I need to enable any protocols? I guess this goes without saying, but I am kind of new to Junos. Update: This is the output from show interfaces terse | match inet: bme0.32768 up up inet 128.0.0.1/2 jsrv.1 up up inet 128.0.0.127/2 vlan.0 up up inet 10.0.1.1/24 vlan.1 up up inet xx.xx.xx.110/30 and this is the output from: show route forwarding-table: Routing table: default.inet Internet: Destination Type RtRef Next hop Type Index NhRef Netif default perm 0 rjct 36 1 0.0.0.0/32 perm 0 dscd 34 1 10.0.1.0/24 intf 0 rslv 1321 1 vlan.0 10.0.1.0/32 dest 0 10.0.1.0 recv 1319 1 vlan.0 10.0.1.1/32 intf 0 10.0.1.1 locl 1320 2 10.0.1.1/32 dest 0 10.0.1.1 locl 1320 2 10.0.1.3/32 dest 1 0:25:90:63:26:53 ucst 1331 2 vlan.0 10.0.1.255/32 dest 0 10.0.1.255 bcst 1318 1 vlan.0

  Read the article

• Nginx unknown limit_req_zone

  - by Kayle

  Nginx currently will not start due to the error mentioned in the title. Here's the actual error I'm getting: $ sudo /etc/init.d/nginx restart Restarting nginx: nginx: [emerg] unknown limit_req_zone "one" in /etc/nginx/sites-enabled/www.myhashimotosthyroiditis.com:15 nginx: configuration file /etc/nginx/nginx.conf test failed And this is immediately following creating the VM in question (www.myhashimotosthyroiditis.com), using a template I found here that was supposedly the "out-of-the-box-for-lazy-people" templates. I'm very new to Nginx and I could not find any helpful information via google or searching here, so I beg my pardon if this is a product of stupidity. Here is the entirety of the VM file: server { listen 80; server_name myhashimotosthyroiditis.com www.myhashimotosthyroiditis.com; root /var/www/myhashimotosthyroiditis; access_log /var/log/nginx/myhashimotosthyroiditis.access.log; error_log /var/log/nginx/myhashimotosthyroiditis.error.log; location / { try_files $uri $uri/ /index.php; } location /search { limit_req zone=one burst=3 nodelay; rewrite ^ /index.php; } fastcgi_intercept_errors off; location ~* \.(?:ico|css|js|gif|jpe?g|png)$ { expires max; add_header Pragma public; add_header Cache-Control "public, must-revalidate, proxy-revalidate"; } include php.conf; # You may want to remove the robots line from drop to use a virtual robots.txt # or create a drop_wp.conf tailored to the needs of the wordpress configuration include drop.conf; }

  Read the article

• Setting up Tomcat6 properly in Ubuntu 10.04

  - by aasukisuki

  We have a Tomcat6 instance running on Ubuntu 10.04LTS. Our test box was just a Windows machine running Tomcat6. Both machines (Linux and Windows) have 1GB of ram. Via the Tomcat configuration tool in windows, I was able to set the min/max/permgen sizes of the JVM. Those were set to 256/512/128 respectively. Now on the Ubuntu box, I've tried setting the JVM options in several different places including: Adding JAVA_OPTS & CATALINA_OPTS in /etc/environment Adding JAVA_OPTS in $CATALINA_HOME/bin/catalina.sh Creating setenv.sh and adding JAVA_OPTS in $CATALINA_HOME/bin Adding JAVA_OPTS directly to /etc/init.d/tomcat6 Un-commenting the JAVA_OPTS and modifying it in /etc/default/tomcat6 Nearly all of those methods did not work, except for modifying /etc/init.d/tomcat6 directly (and possibly the /etc/default/tomcat6 change, but I just did that). However, my understanding is that when you change these settings, only one JVM should be used for the entire tomcat6 instance, and that memory is shared among the applications. On our windows box, tomcat6 is run as a service, and appears to behave this way. However, when I look at htop on the linux box, there are 20+ tomcat6 instances (I have an app that triggers internal jobs every X seconds using chron, so maybe these are threads? Or are they actual instances) all with those memory settings. The app runs fine for a bit, but eventually ends up locking up. I'm guessing each of these apps thinks it has 512m to work with and never GC's and then locks tomcat up completely. What is the proper way to set all of this up?

  Read the article

• DD-WRT: DNSMasq expand-hosts not working

  - by Craig Walker

  I have a Linksys router running DD-WRT (Firmware: DD-WRT v24-sp2 (09/08/09) mini). I have it successfully resolving the DNS names for my DHCP-assigned systems, but only when I fully-qualify those domains. This is despite using the "expand-hosts" DNSMasq additional option, which is supposed to activate this precise function. Here's my dnsmasq.conf: interface=br0 resolv-file=/tmp/resolv.dnsmasq domain=example.com dhcp-leasefile=/tmp/dnsmasq.leases dhcp-lease-max=51 dhcp-option=lan,3,10.77.0.5 dhcp-authoritative dhcp-range=lan,10.77.0.100,10.77.0.149,255.255.0.0,1440m dhcp-host=00:1A:A0:1D:82:5A,astatichostname,10.77.1.40,infinite expand-hosts (FYI: example.com and astatichostname are placeholders for the real-deal names I use. My network uses 10.77.0.0/16; my router is on 10.77.0.5.) Results: > nslookup astatichostname 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 ** server can't find astatichostname: NXDOMAIN > nslookup astatichostname.example.com 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 Name: astatichostname.example.com Address: 10.77.1.40 Is there something else that could be tripping up expand-host in DNSMasq?

  Read the article

• extreme slowness with a remote database in Drupal

  - by ceejayoz

  We're attempting to scale our Drupal installations up and have decided on some dedicated MySQL boxes. Unfortunately, we're running into extreme slowness when we attempt to use the remote DB - page load times go from ~200 milliseconds to 5-10 seconds. Latency between the servers is minimal - a tenth or two of a millisecond. PING 10.37.66.175 (10.37.66.175) 56(84) bytes of data. 64 bytes from 10.37.66.175: icmp_seq=1 ttl=64 time=0.145 ms 64 bytes from 10.37.66.175: icmp_seq=2 ttl=64 time=0.157 ms 64 bytes from 10.37.66.175: icmp_seq=3 ttl=64 time=0.157 ms 64 bytes from 10.37.66.175: icmp_seq=4 ttl=64 time=0.144 ms 64 bytes from 10.37.66.175: icmp_seq=5 ttl=64 time=0.121 ms 64 bytes from 10.37.66.175: icmp_seq=6 ttl=64 time=0.122 ms 64 bytes from 10.37.66.175: icmp_seq=7 ttl=64 time=0.163 ms 64 bytes from 10.37.66.175: icmp_seq=8 ttl=64 time=0.115 ms 64 bytes from 10.37.66.175: icmp_seq=9 ttl=64 time=0.484 ms 64 bytes from 10.37.66.175: icmp_seq=10 ttl=64 time=0.156 ms --- 10.37.66.175 ping statistics --- 10 packets transmitted, 10 received, 0% packet loss, time 8998ms rtt min/avg/max/mdev = 0.115/0.176/0.484/0.104 ms Drupal's devel.module timers show the database queries aren't running any slower on the remote DB - about 150 microseconds whether it's the local or the remote server. Profiling with XHProf shows PHP execution times that aren't out of whack, either. Number of queries doesn't seem to make a difference - we seem the same 5-10 second delay whether a page has 12 queries or 250. Any suggestions about where I should start troubleshooting here? I'm quite confused.

  Read the article

• saslauthd + PostFix producing password verification and authentication errors

  - by Aram Papazian

  So I'm trying to setup PostFix while using SASL (Cyrus variety preferred, I was using dovecot earlier but I'm switching from dovecot to courier so I want to use cyrus instead of dovecot) but I seem to be having issues. Here are the errors I'm receiving: ==> mail.log <== Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: SASL authentication failure: Password verification failed Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: ipname[xx.xx.xx.xx]: SASL PLAIN authentication failed: authentication failure ==> mail.info <== Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: SASL authentication failure: Password verification failed Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: ipname[xx.xx.xx.xx]: SASL PLAIN authentication failed: authentication failure ==> mail.warn <== Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: SASL authentication failure: Password verification failed Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: ipname[xx.xx.xx.xx]: SASL PLAIN authentication failed: authentication failure I tried $testsaslauthd -u xxxx -p xxxx 0: OK "Success." So I know that the password/user I'm using is correct. I'm thinking that most likely I have a setting wrong somewhere, but can't seem to find where. Here is my files. Here is my main.cf for postfix: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname # This is already done in /etc/mailname #myhostname = crazyinsanoman.xxxxx.com smtpd_banner = $myhostname ESMTP $mail_name #biff = no # appending .domain is the MUA's job. #append_dot_mydomain = no readme_directory = /usr/share/doc/postfix # TLS parameters smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # Relay smtp through another server or leave blank to do it yourself #relayhost = smtp.yourisp.com # Network details; Accept connections from anywhere, and only trust this machine mynetworks = 127.0.0.0/8 inet_interfaces = all #mynetworks_style = host #As we will be using virtual domains, these need to be empty local_recipient_maps = mydestination = # how long if undelivered before sending "delayed mail" warning update to sender delay_warning_time = 4h # will it be a permanent error or temporary unknown_local_recipient_reject_code = 450 # how long to keep message on queue before return as failed. # some have 3 days, I have 16 days as I am backup server for some people # whom go on holiday with their server switched off. maximal_queue_lifetime = 7d # max and min time in seconds between retries if connection failed minimal_backoff_time = 1000s maximal_backoff_time = 8000s # how long to wait when servers connect before receiving rest of data smtp_helo_timeout = 60s # how many address can be used in one message. # effective stopper to mass spammers, accidental copy in whole address list # but may restrict intentional mail shots. smtpd_recipient_limit = 16 # how many error before back off. smtpd_soft_error_limit = 3 # how many max errors before blocking it. smtpd_hard_error_limit = 12 # Requirements for the HELO statement smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit # Requirements for the sender details smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit # Requirements for the connecting server smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org # Requirement for the recipient address smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining # require proper helo at connections smtpd_helo_required = yes # waste spammers time before rejecting them smtpd_delay_reject = yes disable_vrfy_command = yes # not sure of the difference of the next two # but they are needed for local aliasing alias_maps = hash:/etc/postfix/aliases alias_database = hash:/etc/postfix/aliases # this specifies where the virtual mailbox folders will be located virtual_mailbox_base = /var/spool/mail/vmail # this is for the mailbox location for each user virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf # and this is for aliases virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf # and this is for domain lookups virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf # this is how to connect to the domains (all virtual, but the option is there) # not used yet # transport_maps = mysql:/etc/postfix/mysql_transport.cf # Setup the uid/gid of the owner of the mail files - static:5000 allows virtual ones virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 inet_protocols=all # Cyrus SASL Support smtpd_sasl_path = smtpd smtpd_sasl_local_domain = xxxxx.com ####################### ## OLD CONFIGURATION ## ####################### #myorigin = /etc/mailname #mydestination = crazyinsanoman.xxxxx.com, localhost, localhost.localdomain #mailbox_size_limit = 0 #recipient_delimiter = + #html_directory = /usr/share/doc/postfix/html message_size_limit = 30720000 #virtual_alias_domains = ##virtual_alias_maps = hash:/etc/postfix/virtual #virtual_mailbox_base = /home/vmail ##luser_relay = webmaster #smtpd_sasl_type = dovecot #smtpd_sasl_path = private/auth smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes #smtpd_sasl_authenticated_header = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination #virtual_create_maildirsize = yes #virtual_maildir_extended = yes #proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $transport_maps $mynetworks $virtual_mailbox_limit_maps #virtual_transport = dovecot #dovecot_destination_recipient_limit = 1 Here is my master.cf: # # Postfix master process configuration file. For details on the format # of the file, see the master(5) manual page (command: "man 5 master"). # # Do not forget to execute "postfix reload" after editing this file. # # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - - - - smtpd submission inet n - - - - smtpd -o smtpd_tls_security_level=encrypt -o smtpd_sasl_auth_enable=yes -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #smtps inet n - - - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - - - - qmqpd pickup fifo n - - 60 1 pickup cleanup unix n - - - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - - 300 1 oqmgr tlsmgr unix - - - 1000? 1 tlsmgr rewrite unix - - - - - trivial-rewrite bounce unix - - - - 0 bounce defer unix - - - - 0 bounce trace unix - - - - 0 bounce verify unix - - - - 1 verify flush unix n - - 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap smtp unix - - - - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - - - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - - - - showq error unix - - - - - error retry unix - - - - - error discard unix - - - - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - - - - lmtp anvil unix - - - - 1 anvil scache unix - - - - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants. # # Many of the following services use the Postfix pipe(8) delivery # agent. See the pipe(8) man page for information about ${recipient} # and other message envelope options. # ==================================================================== # # maildrop. See the Postfix MAILDROP_README file for details. # Also specify in main.cf: maildrop_destination_recipient_limit=1 # maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/bin/maildrop -d ${recipient} # # ==================================================================== # # Recent Cyrus versions can use the existing "lmtp" master.cf entry. # # Specify in cyrus.conf: # lmtp cmd="lmtpd -a" listen="localhost:lmtp" proto=tcp4 # # Specify in main.cf one or more of the following: # mailbox_transport = lmtp:inet:localhost # virtual_transport = lmtp:inet:localhost # # ==================================================================== # # Cyrus 2.1.5 (Amos Gouaux) # Also specify in main.cf: cyrus_destination_recipient_limit=1 # cyrus unix - n n - - pipe user=cyrus argv=/cyrus/bin/deliver -e -r ${sender} -m ${extension} ${user} # # ==================================================================== # Old example of delivery via Cyrus. # #old-cyrus unix - n n - - pipe # flags=R user=cyrus argv=/cyrus/bin/deliver -e -m ${extension} ${user} # # ==================================================================== # # See the Postfix UUCP_README file for configuration details. # uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) # # Other external delivery methods. # ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=bsmtp argv=/usr/lib/bsmtp/bsmtp -t$nexthop -f$sender $recipient scalemail-backend unix - n n - 2 pipe flags=R user=scalemail argv=/usr/lib/scalemail/bin/scalemail-store ${nexthop} ${user} ${extension} mailman unix - n n - - pipe flags=FR user=list argv=/usr/lib/mailman/bin/postfix-to-mailman.py ${nexthop} ${user} #dovecot unix - n n - - pipe # flags=DRhu user=vmail:vmail argv=/usr/lib/dovecot/deliver -d ${recipient} Here is what I'm using for /etc/postfix/sasl/smtpd.conf log_level: 7 pwcheck_method: saslauthd pwcheck_method: auxprop mech_list: PLAIN LOGIN CRAM-MD5 DIGEST-MD5 allow_plaintext: true auxprop_plugin: mysql sql_hostnames: 127.0.0.1 sql_user: xxxxx sql_passwd: xxxxx sql_database: maildb sql_select: select crypt from users where id = '%u' As you can see I'm trying to use mysql as my authentication method. The password in 'users' is set through the 'ENCRYPT()' function. I also followed the methods found in http://www.jimmy.co.at/weblog/?p=52 in order to redo /var/spool/postfix/var/run/saslauthd as that seems to be a lot of people's problems, but that didn't help at all. Also, here is my /etc/default/saslauthd START=yes DESC="SASL Authentication Daemon" NAME="saslauthd" # Which authentication mechanisms should saslauthd use? (default: pam) # # Available options in this Debian package: # getpwent -- use the getpwent() library function # kerberos5 -- use Kerberos 5 # pam -- use PAM # rimap -- use a remote IMAP server # shadow -- use the local shadow password file # sasldb -- use the local sasldb database file # ldap -- use LDAP (configuration is in /etc/saslauthd.conf) # # Only one option may be used at a time. See the saslauthd man page # for more information. # # Example: MECHANISMS="pam" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" I had heard that potentially changing MECHANISM to MECHANISMS="mysql" but obviously that didn't help as is shown by the options listed above and also by trying it out anyway in case the documentation was outdated. So, I'm now at a loss... I have no idea where to go from here or what steps I need to do to get this working =/ Anyone have any ideas? EDIT: Here is the error that is coming from auth.log ... I don't know if this will help at all, but here you go: Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql auxprop plugin using mysql engine Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: begin transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from userPassword user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from cmusaslsecretPLAIN user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: commit transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: begin transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from userPassword user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from cmusaslsecretPLAIN user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: commit transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1'

  Read the article

• Can't get my OpenVpn client to connect

  - by Larry

  Hi Guys, I am trying to setup a test vpn between my home desktop and my laptop. So far I have got the server on the desktop to connect fine but I can not get my laptop to finish the connection. I have tried several different configurations and they all give me the same result. Obviously it has nothing to do with my Client configuration but possibly something on my laptop? Here is the message I get in the log when it stops then times out and restarts. Mon Oct 18 20:10:55 2010 UDPv4 link local: [undef] Mon Oct 18 20:10:55 2010 UDPv4 link remote: 74.190.29.236:1194 Mon Oct 18 20:11:55 2010 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Oct 18 20:11:55 2010 TLS Error: TLS handshake failed here are my configurations server.ovpn port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.1 255.255.255.252 ifconfig-pool-persist ipp.txt push "route 10.0.0.1 255.255.255.0" push "dhcp-option WINS 10.0.0.5" push "dhcp-option DNS 10.0.0.5" push "dhcp-option DOMAIN acme.com.local" keepalive 10 120 comp-lzo max-clients 1 persist-key persist-tun status openvpn-status.log verb 3 LArry.ovpn client proto udp dev tun remote doublel.hopto.org 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client1.crt key client1.key comp-lzo verb 3 dev tun local 206.162.148.9 remote 134.28.54.2 ifconfig 192.168.99.1 192.168.99.2 route 10.0.0.0 255.0.0.0 192.168.99.2 I just need a simple vpn for one user. Am I headed down the right path? Thanks, Larry

  Read the article

• bonding module parameters are not shown in /sys/module/bonding/parameters/

  - by c4f4t0r

  I have a server with Suse 11 sp1 kernel 2.6.32.54-0.3-default, with modinfo bonding i see all parameters, but under /sys/module/bonding/parameters/ not modinfo bonding | grep ^parm parm: max_bonds:Max number of bonded devices (int) parm: num_grat_arp:Number of gratuitous ARP packets to send on failover event (int) parm: num_unsol_na:Number of unsolicited IPv6 Neighbor Advertisements packets to send on failover event (int) parm: miimon:Link check interval in milliseconds (int) parm: updelay:Delay before considering link up, in milliseconds (int) parm: downdelay:Delay before considering link down, in milliseconds (int) parm: use_carrier:Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default) (int) parm: mode:Mode of operation : 0 for balance-rr, 1 for active-backup, 2 for balance-xor, 3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, 6 for balance-alb (charp) parm: primary:Primary network device to use (charp) parm: lacp_rate:LACPDU tx rate to request from 802.3ad partner (slow/fast) (charp) parm: ad_select:803.ad aggregation selection logic: stable (0, default), bandwidth (1), count (2) (charp) parm: xmit_hash_policy:XOR hashing method: 0 for layer 2 (default), 1 for layer 3+4 (charp) parm: arp_interval:arp interval in milliseconds (int) parm: arp_ip_target:arp targets in n.n.n.n form (array of charp) parm: arp_validate:validate src/dst of ARP probes: none (default), active, backup or all (charp) parm: fail_over_mac:For active-backup, do not set all slaves to the same MAC. none (default), active or follow (charp) in /sys/module/bonding/parameters ls -l /sys/module/bonding/parameters/ total 0 -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_grat_arp -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_unsol_na I found some of this parameters under /sys/class/net/bond0/bonding/, but when i try to change one i got the following error echo layer2+3 > /sys/class/net/bond0/bonding/xmit_hash_policy -bash: echo: write error: Operation not permitted

  Read the article

• Amazon Ec2: Problem In Setting up FTP Server

  - by Muntasir

  after setting up My vsFtp Server ON Ec2 i am facing problem , my client is Filezilla and i am getting this error Response: 230 Login successful. Command: OPTS UTF8 ON Response: 200 Always in UTF8 mode. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" Command: TYPE I Response: 200 Switching to Binary mode. Command: PASV Response: 500 OOPS: invalid pasv_address Command: PORT 10,130,8,44,240,50 Response: 500 OOPS: priv_sock_get_cmd Error: Failed to retrieve directory listing Error: Connection closed by server this is the current setting in my vsftpd.conf #nopriv_user=ftpsecure #async_abor_enable=YES # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # chroot_local_user=YES #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list GNU nano 2.0.6 File: /etc/vsftpd/vsftpd.conf # #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES pasv_enable=YES pasv_min_port=2345 pasv_max_port=2355 listen_port=1024 pasv_address=ec2-xxxxxxx.compute-1.amazonaws.com pasv_promiscuous=YES Note: i have already open those port in security group i mean listen port, min max if someone shows me how to fix this i will be very greatful thanks

  Read the article

• Squid external_acl_type Cannot run process

  - by Alex Rezistorman

  I want to restrict uploading for group of the users via squid. So I've choosen to use external_acl_type but after reload of the squid it returns error. WARNING: Cannot run '/usr/local/etc/squid/lists/newupload.sh' process. Permissions of newupload.sh and squid are the same. newupload.sh is executive. How can I solve this problem? Thnx in advance. newupload.sh #!/bin/sh while read line; do set -- $line length=$1 limit=$2 if [ -z "$length" ] || [ "$length" -le "$2" ]; then echo OK else echo ERR fi done Strings from squid.conf external_acl_type request_body protocol=2.5 %{Content-Lenght} /usr/local/etc/squid/lists/newupload.sh acl request_max_size external request_body 5000 http_access allow users request_max_size Squid version squid -v Squid Cache: Version 3.2.13 configure options: '--with-default-user=squid' '--bindir=/usr/local/sbin' '--sbindir=/usr/local/sbin' '--datadir=/usr/local/etc/squid' '--libexecdir=/usr/local/libexec/squid' '--localstatedir=/var' '--sysconfdir=/usr/local/etc/squid' '--with-logdir=/var/log/squid' '--with-pidfile=/var/run/squid/squid.pid' '--with-swapdir=/var/squid/cache/squid' '--enable-auth' '--enable-build-info' '--enable-loadable-modules' '--enable-removal-policies=lru heap' '--disable-epoll' '--disable-linux-netfilter' '--disable-linux-tproxy' '--disable-translation' '--enable-auth-basic=PAM' '--disable-auth-digest' '--enable-external-acl-helpers= kerberos_ldap_group' '--enable-auth-negotiate=kerberos' '--disable-auth-ntlm' '--without-pthreads' '--enable-storeio=diskd ufs' '--enable-disk-io=AIO Blocking DiskDaemon IpcIo Mmapped' '--enable-log-daemon-helpers=file' '--disable-url-rewrite-helpers' '--disable-ipv6' '--disable-snmp' '--disable-htcp' '--disable-forw-via-db' '--disable-cache-digests' '--disable-wccp' '--disable-wccpv2' '--disable-ident-lookups' '--disable-eui' '--disable-ipfw-transparent' '--disable-pf-transparent' '--disable-ipf-transparent' '--disable-follow-x-forwarded-for' '--disable-ecap' '--disable-icap-client' '--disable-esi' '--enable-kqueue' '--with-large-files' '--enable-cachemgr-hostname=proxy.adir.vbr.ua' '--with-filedescriptors=131072' '--disable-auto-locale' '--prefix=/usr/local' '--mandir=/usr/local/man' '--infodir=/usr/local/info/' '--build=amd64-portbld-freebsd8.3' 'build_alias=amd64-portbld-freebsd8.3' 'CC=cc' 'CFLAGS=-O2 -fno-strict-aliasing -frename-registers -fweb -fforce-addr -fmerge-all-constants -maccumulate-outgoing-args -pipe -march=core2 -I/usr/local/include -DLDAP_DEPRECATED' 'LDFLAGS= -L/usr/local/lib' 'CPPFLAGS=-I/usr/local/include' 'CXX=c++' 'CXXFLAGS=-O2 -fno-strict-aliasing -frename-registers -fweb -fforce-addr -fmerge-all-constants -maccumulate-outgoing-args -pipe -march=core2 -I/usr/local/include -DLDAP_DEPRECATED' 'CPP=cpp' --enable-ltdl-convenience Related post: Restrict uploading for groups in squid http://squid-web-proxy-cache.1019090.n4.nabble.com/flexible-managing-of-request-body-max-size-with-squid-2-5-STABLE12-td1022653.html

  Read the article

• QoS for Cisco Router to Prioritize Voice and Interactive Traffic

  - by TJ Huffington

  I have a Cisco 891W NATing Voice and Data to the internet over a 10mbit/2mbit connection. Voice traffic gets degraded when I upload large files. Pings time out as well. I tried to configure a QoS policy but it's basically not doing anything. Voice traffic still degrades when upload bandwidth gets saturated. Here is my current configruation: class-map match-any QoS-Transactional match protocol ssh match protocol xwindows class-map match-any QoS-Voice match protocol rtp audio class-map match-any QoS-Bulk match protocol secure-nntp match protocol smtp match protocol tftp match protocol ftp class-map match-any QoS-Management match protocol snmp match protocol dns match protocol secure-imap class-map match-any QoS-Inter-Video match protocol rtp video class-map match-any QoS-Voice-Control match access-group name Voice-Control policy-map QoS-Priority-Output class QoS-Voice priority percent 25 set dscp ef class QoS-Inter-Video bandwidth remaining percent 10 set dscp af41 class QoS-Transactional bandwidth remaining percent 25 random-detect dscp-based set dscp af21 class QoS-Bulk bandwidth remaining percent 5 random-detect dscp-based set dscp af11 class QoS-Management bandwidth remaining percent 1 set dscp cs2 class QoS-Voice-Control priority percent 5 set dscp ef class class-default fair-queue interface FastEthernet8 bandwidth 1024 bandwidth receive 20480 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto auto discovery qos crypto map mymap max-reserved-bandwidth 80 service-policy output QoS-Priority-Output crypto map mymap 10 ipsec-isakmp set peer 1.2.3.4 default set transform-set ESP-3DES-SHA match address 110 qos pre-classify ! fa8 is my connection to the internet. Voice traffic goes over a VPN ("mymap") to the SIP server. That's why I specified "qos pre-classify" which I believe is the way to classify traffic over the VPN. However even when I ping a public IP while saturating upload bandwidth, the latency is exceptionally high. Is this configuration correct? Are there any suggestions that might make this work for my setup? Thanks in advance.

  Read the article

• QoS for Cisco Router to Prioritize Voice and Interactive Traffic

  - by TJ Huffington

  I have a Cisco 891W NATing Voice and Data to the internet over a 10mbit/2mbit connection. Voice traffic gets degraded when I upload large files. Pings time out as well. I tried to configure a QoS policy but it's basically not doing anything. Voice traffic still degrades when upload bandwidth gets saturated. Here is my current configruation: class-map match-any QoS-Transactional match protocol ssh match protocol xwindows class-map match-any QoS-Voice match protocol rtp audio class-map match-any QoS-Bulk match protocol secure-nntp match protocol smtp match protocol tftp match protocol ftp class-map match-any QoS-Management match protocol snmp match protocol dns match protocol secure-imap class-map match-any QoS-Inter-Video match protocol rtp video class-map match-any QoS-Voice-Control match access-group name Voice-Control policy-map QoS-Priority-Output class QoS-Voice priority percent 25 set dscp ef class QoS-Inter-Video bandwidth remaining percent 10 set dscp af41 class QoS-Transactional bandwidth remaining percent 25 random-detect dscp-based set dscp af21 class QoS-Bulk bandwidth remaining percent 5 random-detect dscp-based set dscp af11 class QoS-Management bandwidth remaining percent 1 set dscp cs2 class QoS-Voice-Control priority percent 5 set dscp ef class class-default fair-queue interface FastEthernet8 bandwidth 1024 bandwidth receive 20480 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto auto discovery qos crypto map mymap max-reserved-bandwidth 80 service-policy output QoS-Priority-Output crypto map mymap 10 ipsec-isakmp set peer 1.2.3.4 default set transform-set ESP-3DES-SHA match address 110 qos pre-classify ! fa8 is my connection to the internet. Voice traffic goes over a VPN ("mymap") to the SIP server. That's why I specified "qos pre-classify" which I believe is the way to classify traffic over the VPN. However even when I ping a public IP while saturating upload bandwidth, the latency is exceptionally high. Is this configuration correct? Are there any suggestions that might make this work for my setup? Thanks in advance.

  Read the article

• mod_perl loses STDOUT in middle of request

  - by puzzled72

  Hi, I have been having this weird issue where mod_perl seems to lose STDOUT in the middle of the request. So far I have eliminated everything I could think of. You might have seen this bug related to the following errors in error_log : Apache2 IO flush: (103) Apache2::RequestIO::read: (104) Software caused connection abort They are all the same error. It happens when the perl script running under mod_perl loses STDOUT when trying to print the result back to apache. I only notice this error on my servers running the following: (centos5.4) Perl 5.8.8-27 mod_perl 2.0.4-6 httpd 2.2.3-31 kernel-2.6.18-164.15.1 It's not the code This code has been working for months It's not network related The browser gets the error response from apache. It's not time related I get the error 15 or so seconds after I restart httpd It's not idle httpd related I have tried reducing the min/max SpareServers to 1 It's not load related I get the error even if there are only 10 sessions on httpd It's not related to the "fd < PERLIO_MAX_REFCOUNTABLE_FD" perl 5.8.8 bug I recompiled perl-5.8.8 with the patch mentioned here : https://bugzilla.redhat.com/show_bug.cgi?id=559832, same error. It appeared sometime between December 2009 and February 2010 sorry I cannot be more specific Anyone has any idea ? Anything that I have not tested ? Really Puzzled!

  Read the article

• flask, lighttpd with fastcgi can't get it to work

  - by kurojishi

  i'm tring to deploy a simple flask script to a lighttpd server with fastcgi. this is the configuration file for lighttpd builded using the flask documentation http://flask.pocoo.org/docs/deploying/fastcgi/#configuring-lighttpd server.modules = ( "mod_access", "mod_alias", "mod_compress", "mod_redirect", "mod_rewrite", "mod_fastcgi", ) server.document-root = "/var/www" server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) server.errorlog = "/var/log/lighttpd/error.log" server.pid-file = "/var/run/lighttpd.pid" server.username = "www-data" server.groupname = "www-data" index-file.names = ( "index.php", "index.html", "index.htm", "default.htm", " index.lighttpd.html" ) url.access-deny = ( "~", ".inc" ) static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) var.home_dir = "/var/lib/lighttpd" var.socket_dir = home_dir + "sockets/" ## Use ipv6 if available #include_shell "/usr/share/lighttpd/use-ipv6.pl" dir-listing.encoding = "utf-8" server.dir-listing = "enable" compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ( "application/x-javascript", "text/css", "text/html", "text/plain" ) include_shell "/usr/share/lighttpd/create-mime.assign.pl" include_shell "/usr/share/lighttpd/include-conf-enabled.pl" fastcgi.server = ("weibo/callback.fcgi" => (( "socket" => "/tmp/weibocrawler-fcgi.sock", "bin-path" => "/var/www/weibo/callback.fcgi", "check-local" => "disable", "max-procs" => 1 )) ) url.rewrite-once = ( "^(/weibo($|/.*))$" => "$1", "^(/.*)$" => "weibo/callback.fcgi$1" and this is the script i'm tring to run: #!/home/nrl/kuro/weiboenv/bin/python from flup.server.fcgi import WSGIServer from callback import app if __name__ == '__main__': WSGIServer(application, bindAddress='/tmp/weibocrawler-fcgi.sock').run() but i have this error testing the configuration file i get this error: 2013-07-02 17:15:42: (configfile.c.912) source: lighttpd.conf.new line: 52 pos: 1 parser failed somehow near here: weibo/callback.fcgi$1 when i remove the urlrewrite i get these errors in the log even if the daemon start: 2013-07-02 16:25:53: (log.c.166) server started 2013-07-02 16:25:53: (mod_fastcgi.c.1104) the fastcgi-backend fcgi.py failed to start: 2013-07-02 16:25:53: (mod_fastcgi.c.1108) child exited with status 2 fcgi.py 2013-07-02 16:25:53: (mod_fastcgi.c.1111) If you're trying to run your app as a FastCGI backend, make sure you're using the FastCGI-enabled version. If this is PHP on Gentoo, add 'fastcgi' to the USE flags. 2013-07-02 16:25:53: (mod_fastcgi.c.1399) [ERROR]: spawning fcgi failed. 2013-07-02 16:25:53: (server.c.938) Configuration of plugins failed. Going down.

  Read the article

• VMWare ESX, storage over 2TB

  - by Phliplip

  Hi, First of, i'm a webdeveloper and my server experience lies in setting up FreeBSD servers for webserver. I'm working on a project for at photographer, and i'm hired to develop a new online photo ordering system - where user of course can view their photos :) They have a massive need of storage, thus we have bought a HP G6 and 8x1TB SATA HDD. Our plan is to install VMWare ESX 4.0, running multiple virtual machines; FreeBSD 8 for webserver and some windows servers. Allready done that. Then mount one big storage to the BSD, and share it through Samba to the WinServers. The raid is set up with an array of 2x 1TB to handle the VMs. And the rest is setup as 3 2x1TB to handle the photo-data. Thus 2.73TB for photo-data (the raids are 1+0). Now if we add a datastore in the ESX and add the 3 LUNs we can get a datastore of 2.74TB. But i don't se how i can add this datastore direct to the VM. Only the BSD VM needs access to this. Only way is to create a VirtualDisk, with a max of 2TB (8MB blocksize). This is because the datastore where we save the virtualdisk has a maximum filesize of 2TB. Then add it as a harddisk to the BSD VM. In the 'Add Harddisk' pane for the VM, i see an option for Raw Disk Management. I think this is to access the datastore or the raid directly. Only problem is that its greyed out! Can i access the datastorage directly from the BSD? Without creating and adding virtualdisk.

  Read the article

• Ipsec config problem // openswan

  - by user90696

  I try to configure Ipsec on server with openswan as client. But receive error - possible, it's auth error. What I wrote wrong in config ? Thank you for answers. #1: STATE_MAIN_I2: sent MI2, expecting MR2 003 "f-net" #1: received Vendor ID payload [Cisco-Unity] 003 "f-net" #1: received Vendor ID payload [Dead Peer Detection] 003 "f-net" #1: ignoring unknown Vendor ID payload [ca917959574c7d5aed4222a9df367018] 003 "f-net" #1: received Vendor ID payload [XAUTH] 108 "f-net" #1: STATE_MAIN_I3: sent MI3, expecting MR3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 010 "f-net" #1: STATE_MAIN_I3: retransmission; will wait 20s for response 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 010 "f-net" #1: STATE_MAIN_I3: retransmission; will wait 40s for response 031 "f-net" #1: max number of retransmissions (2) reached STATE_MAIN_I3. Possible authentication failure: no acceptable response to our first encrypted message 000 "f-net" #1: starting keying attempt 2 of at most 3, but releasing whack other side - Cisco ASA. parameters for my connection on our Linux server : VPN Gateway 8.*.*.* (Cisco ) Phase 1 Exchange Type Main Mode Identification Type IP Address Local ID 4.*.*.* (our Linux server IP) Remote ID 8.*.*.* (VPN server IP) Authentication PSK Pre Shared Key Diffie-Hellman Key Group DH 5 (1536 bit) or DH 2 (1024 bit) Encryption Algorithm AES 256 HMAC Function SHA-1 Lifetime 86.400 seconds / no volume limit Phase 2 Security Protocol ESP Connection Mode Tunnel Encryption Algorithm AES 256 HMAC Function SHA-1 Lifetime 3600 seconds / 4.608.000 kilobytes DPD / IKE Keepalive 15 seconds PFS off Remote Network 192.168.100.0/24 Local Network 1 10.0.0.0/16 ............... Local Network 5 current openswan config : # config setup klipsdebug=all plutodebug="control parsing" protostack=netkey nat_traversal=no virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn f-net type=tunnel keyexchange=ike authby=secret auth=esp esp=aes256-sha1 keyingtries=3 pfs=no aggrmode=no keylife=3600s ike=aes256-sha1-modp1024 # left=4.*.*.* leftsubnet=10.0.0.0/16 leftid=4.*.*.* leftnexthop=%defaultroute right=8.*.*.* rightsubnet=192.168.100.0/24 rightid=8.*.*.* rightnexthop=%defaultroute auto=add

  Read the article

• Ubuntu/Nvidia lists DVI dual cable as single

  - by Joseph Mastey

  I have an NVidia Quadro FX 880M graphics card, from which I am trying to drive 2 monitors: my internal laptop montior (15.6", 1920x1080, Nvidia driver says it's running via DisplayPort) and an external 27" monitor (Dell U2711, 2560x1440 native resolution, via DVI). I've hooked the dual DVI cable to the dual DVI port on my dock (Dell PR03X) and installed the proprietary NVidia driver, but I cannot seem to get the full 2560x1440 out of the larger 27" external monitor. Looking at the NVidia driver settings, the monitor's connection is reported as a single DVI cable, rather than a dual one, which would explain the reduced resolution. Does anyone have any experience with an issue like this? What can I do to make full use of my new monitor? (Possibly) Relevant Information: There is no DVI port on the laptop itself, but one is provided via the dock. The laptop and dock both provide a DisplayPort jack, but I have been unable to get this working on either w/ the monitor. I did have the nouveau driver installed when I installed the nvidia proprietary driver, but have since removed it (no change in the monitor situation when I removed it). The 27" reports a max resolution of 1680x1050. Thanks, Joe

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

• Problems setting up a VPN: can connect but can't ping anyone

  - by Fernando

  This is my first time setting a VPN. Clients can connect but can't ping other machines. This is certainly a route problem but i can't find the right way to configure it. Here is a sample example of the two LANS i want to connect: So, i want machines from 192.168.1.0/24 being able to connect with 192.168.0.0/24 as if they were on the same network. For the VPN network, i would like to use the 10.0.0.0/24 range. Here is my server.conf: proto udp port 1194 dev tun server 10.0.0.0 255.255.255.0 push "route 192.168.0.0 255.255.255.0 192.168.0.1" push "dhcp-option DNS 192.168.0.1" push "dhcp-option WINS 192.168.0.1" comp-lzo keepalive 10 120 float max-clients 10 persist-key persist-tun log-append /var/log/openvpn.log verb 6 tls-server dh /etc/openvpn/keys/dh1024.pem ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key tls-auth /etc/openvpn/keys/mykey.key 0 status /var/log/openvpn.stats And one of my clients 192.168.1.2: client dev tap proto udp remote my.no-ip.address 1194 route 192.168.1.0 255.0.0.0 192.168.1.1 3 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\test1.crt" key "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\test1.key" tls-auth "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\mykey.key" 1 ns-cert-type server cipher BF-CBC comp-lzo verb 1 What exactly i am doing wrong? All machines can connect to openvpn but the ping doesn't work. At the client log i see the following error: Wed Feb 16 09:43:23 2011 OpenVPN ROUTE: OpenVPN needs a gateway parameter for a --route option and no default was specified by either --route-gateway or --ifconfig options Wed Feb 16 09:43:23 2011 OpenVPN ROUTE: failed to parse/resolve route for host/network: 10.0.0.1 Thanks!

  Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >