Search Results

Search found 22447 results on 898 pages for 'message bus'.

Page 149/898 | < Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >

• Nagios3 gives a warning on HTTP service monitoring

  - by Dez

  Already set up my local net configuration to be monitored by Nagios3. I found a problem that Nagios3 reports a warning in the HTTP monitoring service of a Debian server set at ip 192.168.1.52, that has an individual virtual host and a mass virtual host for application development. I get this status message: HTTP WARNING: HTTP/1.1 404 Not Found I used the Nagios tools to check. servername is the name of the vhost server name I used in the Apache configuration. /usr/lib/nagios/plugins/check_http -H servername -I 192.168.1.52 receiving this status message: HTTP OK HTTP/1.1 200 OK - 37900 bytes in 0.504 seconds |time=0.503946s;;;0.000000 size=37900B;;;0 But when I check like this: /usr/lib/nagios/plugins/check_http -I 192.168.1.52 I get the same status message as the warning, so I assume that I don't have Nagios completely well set up because doesn't recognize the vhosts for that server, how it should be as the check_http service shows. Where should I look to fix that warning?

  Read the article

• dpkg behaving strangely?

  - by Tom Henderson

  When I use apt to get a package, I have been receiving the same error message. Here is an example trying to install wicd (which is already installed): Reading package lists... Building dependency tree... Reading state information... wicd is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 1 not upgraded. 3 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up tex-common (2.06) ... debconf: unable to initialize frontend: Dialog debconf: (Dialog frontend requires a screen at least 13 lines tall and 31 columns wide.) debconf: falling back to frontend: Readline Running mktexlsr. This may take some time... done. No packages found matching texlive-base. dpkg: error processing tex-common (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of texlive-binaries: texlive-binaries depends on tex-common (>= 2.00); however: Package tex-common is not configured yet. dpkg: error processing texlive-binaries (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of dvipng: dvipng depends on texlive-base-bin; however: Package texlive-base-bin is not installed. Package texlive-binaries which provides texlive-base-bin is not configured yet. dpkg: error processing dvipng (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: tex-common texlive-binaries dvipng E: Sub-process /usr/bin/dpkg returned an error code (1) I'm not sure if this is a problem with apt or with dpkg, but it certainly doesn't look good!

  Read the article

• RealTek RTL8188CE WiFi adapter doesn't connect reliably

  - by ken.ganong

  I recently bought a new system76 laptop which came pre-installed with Ubuntu 11.10. I've been having trouble with my wireless connectivity. It seems that my connection with my wireless network keeps going in and out. It is not my network--I have seen the same problem on multiple WiFi networks and at different distances and reported link qualities. OS version: Ubuntu 11.10 oneiric kernel version: 3.0.0-14-generic lspci: lspci -nnk | grep -iA2 net 04:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:9196] Kernel driver in use: rtl8192ce -- 05:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) Subsystem: CLEVO/KAPOK Computer Device [1558:2500] Kernel driver in use: jme iwconfig: iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"peppermintpatty" Mode:Managed Frequency:2.462 GHz Access Point: 98:FC:11:6C:E0:22 Bit Rate=72.2 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Power Management:off Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:1103 Missed beacon:0 lshw: sudo lshw -class network *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 00:1c:7b:a1:95:04 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.0.0-14-generic firmware=N/A ip=192.168.1.106 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:18 ioport:e000(size=256) memory:f7d00000-f7d03fff *-network description: Ethernet interface product: JMC250 PCI Express Gigabit Ethernet Controller vendor: JMicron Technology Corp. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 00:90:f5:c0:42:b3 size: 10Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:56 memory:f7c20000-f7c23fff ioport:d100(size=128) ioport:d000(size=256) memory:f7c10000-f7c1ffff memory:f7c00000-f7c0ffff Any help would be appreciated. The last time I've dealt with wireless issues, the most given solution was NDIS wrapper and I seem sorely out-of-date.

  Read the article

• DriveSafe.ly Reads Your Text Messages Aloud

  - by ETC

  DriveSafe.ly, a free application for Android and BlackBerry phones, reads your text messages, emails, and caller ID notifications aloud so you can stay connected while keeping your eyes on the road. DriveSafe.ly is a feature packed application that reads your text messages, your emails, and the ID from your caller ID aloud. It’s not the only SMS-to-speech application out there but it sports the most featured including rocking a customizable auto-responder (so you can let people know you heard their message and will respond as soon as you’re off the road), the ability to customize the voice and the read-rate, how much information if given (the senders name or just the message or the senders name, subject, and message in the case of emails), and more. Upgrading to the $13.95 a year premium version allows voice-to-txt translation so you can respond verbally to your text messages and emails. Hit up the link below to read more and grab a copy for your Android or BlackBerry phone. DriveSafe.ly [via Addictive Tips] Latest Features How-To Geek ETC Have You Ever Wondered How Your Operating System Got Its Name? Should You Delete Windows 7 Service Pack Backup Files to Save Space? What Can Super Mario Teach Us About Graphics Technology? Windows 7 Service Pack 1 is Released: But Should You Install It? How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions How to Enable User-Specific Wireless Networks in Windows 7 DriveSafe.ly Reads Your Text Messages Aloud The Likability of Angry Birds [Infographic] Dim an Overly Bright Alarm Clock with a Binder Divider Preliminary List of Keyboard Shortcuts for Unity Now Available Bring a Touch of the Wild West to Your Desktop with the Rango Theme for Windows 7 Manage Your Favorite Social Accounts in Chrome and Iron with Seesmic

  Read the article

• Getting codebaseHQ SVN ChangeLog data in your application

  - by saifkhan

  I deploy apps via ClickOnce. After each deployment we have to review the changes made and send out an email to the users with the changes. What I decided now to do is to use CodebaseHQ’s API to access a project’s SVN repository and display the commit notes so some users who download new updates can check what was changed or updated in an app. This saves a heck of a lot of time, especially when your apps are in beta and you are making several changes daily based on feedback. You can read up on their API here Here is a sample on how to access the Repositories API from a windows app Public Sub GetLog() If String.IsNullOrEmpty(_url) Then Exit Sub Dim answer As String = String.Empty Dim myReq As HttpWebRequest = WebRequest.Create(_url) With myReq .Headers.Add("Authorization", String.Format("Basic {0}", Convert.ToBase64String(Encoding.ASCII.GetBytes("username:password")))) .ContentType = "application/xml" .Accept = "application/xml" .Method = "POST" End With Try Using response As HttpWebResponse = myReq.GetResponse() Using sr As New System.IO.StreamReader(response.GetResponseStream()) answer = sr.ReadToEnd() Dim doc As XDocument = XDocument.Parse(answer) Dim commits = From commit In doc.Descendants("commit") _ Select Message = commit.Element("message").Value, _ AuthorName = commit.Element("author-name").Value, _ AuthoredDate = DateTime.Parse(commit.Element("authored-at").Value).Date grdLogData.BeginUpdate() grdLogData.DataSource = commits.ToList() grdLogData.EndUpdate() End Using End Using Catch ex As Exception MsgBox(ex.Message) End Try End Sub

  Read the article

• Email bouces to tell me it was delivered?

  - by flamey

  I get this back after sending an email. It says "Your message was successfully delivered", then why do I even get this? Or this phrase referes to something else? Reporting-MTA: dns; gmmr6.centrum.cz X-Postfix-Queue-ID: CDBBB8016CE1 X-Postfix-Sender: rfc822; [SENDER_EMAIL] Arrival-Date: Sat, 5 Mar 2011 22:04:41 +0100 (CET) Final-Recipient: rfc822; [RECIPIENT_EMAIL] Original-Recipient: rfc822;[RECIPIENT_EMAIL] Action: delivered Status: 2.0.0 Diagnostic-Code: X-Postfix; delivery via maildaemon: OK This is the mail system at host gmmr6.centrum.cz. Your message was successfully delivered to the destination(s) listed below. If the message was delivered to mailbox you will receive no further notifications. Otherwise you may still receive notifications of mail delivery errors from other systems. The mail system <[RECIPIENT_EMAIL]>;: delivery via maildaemon: OK

  Read the article

• What does the `dmesg` error: "composite sync not supported" mean?

  - by M. Tibbits

  Question: I see [ 20.473125] composite sync not supported and several such entries when I run dmesg. What do they mean? Background: I'm trying to debug a problem where my laptop won't suspend. Since acpi seems happy and I can suspend easily from the command line, I've turned to tracking down all boot-up errors/warnings. So I run dmesg | grep not and, amongst other shtuff, I get: 728:[ 17.267120] composite sync not supported 733:[ 18.009061] composite sync not supported 740:[ 18.159289] registered panic notifier 749:[ 18.162500] vga16fb: not registering due to another framebuffer present 757:[ 18.598251] composite sync not supported 776:[ 20.473125] composite sync not supported 777:[ 20.932266] composite sync not supported 778:[ 28.350231] composite sync not supported 779:[ 28.924913] composite sync not supported 780:[ 35.480658] composite sync not supported And the full log for the few lines right around that first appearance (line 728) is listed at the bottom of my post (I'd happily include anything else). Any ideas what could be causing this? I've read several sites: Ubuntuforums #1 IRC Chat #1 One post talks about ??Adobe flash?? causing this error? Some others also suggest that it might be an nvidia related problem, but I've got a Dell Latitude D630 with an integrated Intel graphics -- so nvidia isn't the problem. [ 17.207142] phy0: Selected rate control algorithm 'minstrel' [ 17.207833] Registered led device: b43-phy0::tx [ 17.207849] Registered led device: b43-phy0::rx [ 17.207865] Registered led device: b43-phy0::radio [ 17.207927] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ] [ 17.267120] composite sync not supported [ 17.415795] EXT4-fs (sda2): mounted filesystem with ordered data mode [ 17.602131] [drm] initialized overlay support [ 17.620201] input: DualPoint Stick as /devices/platform/i8042/serio1/input/input7 [ 17.641192] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input8 [ 18.009061] composite sync not supported [ 18.106042] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean. [ 18.108115] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean. [ 18.108941] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean. [ 18.109676] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean. [ 18.110356] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean. [ 18.159286] fb0: inteldrmfb frame buffer device [ 18.159289] registered panic notifier [ 18.160218] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:01/input/input9 [ 18.160286] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no) [ 18.160334] ACPI Warning for \_SB_.PCI0.VID2._DOD: Return Package has no elements (empty) (20090903/nspredef-433) [ 18.160432] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:02/input/input10 [ 18.160491] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) [ 18.160539] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 18.162494] vga16fb: initializing [ 18.162497] vga16fb: mapped to 0xc00a0000 [ 18.162500] vga16fb: not registering due to another framebuffer present [ 18.176091] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 18.176123] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 18.285752] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input11 [ 18.312497] input: HDA Intel Mic at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 18.312586] input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 18.328043] usbcore: registered new interface driver ndiswrapper [ 18.460909] Console: switching to colour frame buffer device 180x56 [ 18.598251] composite sync not supported

  Read the article

• Stable MSN messenger for mac?

  - by Console

  I use Adium in my mac as a client for MSN messenger. (I have also tried the "official" live messenger for mac for a while but it had even worse issues than what I am experiencing with Adium). Everything works fine for the first 5-10 minutes, perhaps until the first automatic "away", then suddenly any message I send is followed by a dozen or so messages saying: "Message could not be sent because a connection error occurred:" and Message may have not been sent because a timeout occurred: If I send a few messages, they usually eventually arrive (all at once) after a long delay. Windows machines on the same network running live messenger work fine. Any ideas why this might be, or suggestions for a client that might work when both Adium and Microsofts own messenger for mac seem to disconnect?

  Read the article

• Delete file then run file at startup

  - by Henry Gibson

  I'm running the music player Foobar2000 through Wine at startup. For some reason when I shutdown Ubuntu the Foobar2000 process is ended abnormally in Wine and when it runs next time I get an annoying "start in safe mode?" message. Not a huge problem, but I'd like it fixed. The safe mode message only appears if a file called "running" is present when Foobar2000 starts (if it isn't deleted when closed properly). So by deleting "running" then starting Foobar2000, the message doesn't appear. I thought it would be easy enough to enter this as a startup command, however it doesn't want to work. The command I am using is rm '/home/henry/.wine/drive_c/users/henry/Application Data/foobar2000/running';'/home/henry/.wine/drive_c/Program Files (x86)/foobar2000/foobar2000.exe' which works fine if I just run it from terminal, the file is deleted then foobar2000 runs. Does anyone know why this isn't working at startup? Also, will this run with a terminal visible? How can I make just the gui appear? Thanks

  Read the article

• NetworkManager broken after upgrade to Kubuntu Saucy

  - by queueoverflow

  I had Kubuntu 13.04 on my ThinkPad X220, and I upgraded to 13.10 and I am not able to connect to a wired or wireless connection. The new network tray icon does not show any entries at all. In the menu of the tray icon, there is an error saying: Require NetworkManager 0.9.8, found . I then tried the following: nmcli con ** (process:3695): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Rejected send message, 3 matched rules; type="method_call", sender=":1.64" (uid=1000 pid=3695 comm="nmcli con ") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination="org.freedesktop.NetworkManager" (uid=0 pid=1116 comm="NetworkManager ") Error: nmcli (0.9.8.0) and NetworkManager (unknown) versions don't match. Force execution using --nocheck, but the results are unpredictable. nmcli dev ** (process:3700): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Rejected send message, 3 matched rules; type="method_call", sender=":1.65" (uid=1000 pid=3700 comm="nmcli dev ") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination="org.freedesktop.NetworkManager" (uid=0 pid=1116 comm="NetworkManager ") Error: nmcli (0.9.8.0) and NetworkManager (unknown) versions don't match. Force execution using --nocheck, but the results are unpredictable. nm-tool ** (process:3705): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Rejected send message, 3 matched rules; type="method_call", sender=":1.66" (uid=1000 pid=3705 comm="nm-tool ") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination="org.freedesktop.NetworkManager" (uid=0 pid=1116 comm="NetworkManager ") NetworkManager Tool State: unknown ** (process:3705): WARNING **: error: could not connect to NetworkManager Running those as root works, however. I was also able to run nmcli con up id DHCP which got my DHCP connection working and giving me internet access. That did not work using a Wifi connection though, and I do need those. How can I get networking back to work without a reinstall?

  Read the article

• Wireless acting weird ubuntu 12.04 LTS

  - by Philip Yeldhos

  I'm kinda new here, so please bear with me. My wireless driver is acting very weird. It shows my router's name, but when it is connecting (after entering the correct password), the icon on the tray is like, refreshing every once in a second, while showing the animation that it is connecting. And after a few seconds, error message come up saying that wireless network is disconnected. I installed the drive through "additional drivers". What info do you need? Somebody please help. philip@philip-HP-Mini-110-3100:~$ sudo iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.472 GHz Access Point: Not-Associated Bit Rate:72 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:11 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. here's what lspci -v gave me: 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Device 1483 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at 52000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-82-ff-ff-3f-e0-2a Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac okay, i removed the driver additional drivers gave me. now, this is what has happened: lsmod gave me: philip@philip-HP-Mini-110-3100:~$ lsmod | grep brc brcmsmac 540875 0 mac80211 436455 1 brcmsmac brcmutil 14675 1 brcmsmac cfg80211 178679 2 brcmsmac,mac80211 crc8 12781 1 brcmsmac cordic 12487 1 brcmsmac and iwconfig gave me: philip@philip-HP-Mini-110-3100:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. and lspci -v gave me: 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Device 1483 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at 52000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• Configuring Touchpad Multi-Tap on Ubuntu 11.10

  - by nunos

  I am having a hard time configuring my notebook's touchpad. I can do everything I can in Windows with the exception of three-finger tap, which doesn't work, and the action of two-finger tap which is giving me the equivalent to a right-mouse click, when I wanted a middle-mouse click. I read on a forum to use this as a guide. The problem is that I can't even find the configuration file /etc/X11/xorg.conf.d/10-synaptics.conf. I tried running pacman -S xf86-input-synaptics but I don't have the pacman program installed. When I try to install it by sudo apt-get install I get a pacman game instead! I know the guide is for archlinux, so maybe that's why it doesn't work with me. I am running Ubuntu 11.10 on an Asus N82JV. Any help on this is appreciated. Here's the output of xinput list: nuno@mozart:~$ xinput list ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? Microsoft Microsoft® Nano Transceiver v2.0 id=12 [slave pointer (2)] ? ? Microsoft Microsoft® Nano Transceiver v2.0 id=13 [slave pointer (2)] ? ? ETPS/2 Elantech Touchpad id=16 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Video Bus id=8 [slave keyboard (3)] ? Sleep Button id=9 [slave keyboard (3)] ? USB2.0 2.0M UVC WebCam id=10 [slave keyboard (3)] ? Microsoft Microsoft® Nano Transceiver v2.0 id=11 [slave keyboard (3)] ? Asus Laptop extra buttons id=14 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=15 [slave keyboard (3)]

  Read the article

• How do I get wireless working on a Dell Inspiron 510m?

  - by user17449

  Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

  Read the article

• Original sender is not correctly identified when spam is forwarded

  - by Stephan Burlot

  I have a forwarding rule with Postfix that forwards all messages to my main email address. When a spam message is sent to one of my emails, it is forwarded but the sender is shown as being the forwarding domain, not the spammer's domain. Real example: mywebsite.com is hosted on Linode. [email protected] sends an email to [email protected] the mail is forwarded to [email protected] my email hosting (anotherwebsite.com) sees it's spam and sends a message to [email protected] and Linode reports a TOS violation. I have modified my postfix settings so I now use RBL, but if a message goes through, it may happen again. How can I prevent this to happen again? Is there some settings to change on Postfix so the original sender is correctly identified? Thanks Stephan EDIT: The steps I did to prevent this to happen again are: Add RBL checking to Postfix Add postgrey to Postfix And finally fix the MX record which was incorrect. I checked with a test email on Spamcop.net and the original sender is correctly identified.

  Read the article

• Design Application to "Actively" Invite Users (pretend they have privileges)

  - by user3086451

  I am designing an application where users message one another privately, and may send messages to any Entity in the database (an Entity may not have a user account yet, it is a professional database). I am not sure how to best design the database and the API to allow messaging unregistered users. The application should remain secure, and data only accessed by those with correct permissions. Messages sent to persons without user accounts serve as an invitation. The invited person should be able to view the message, act on it, and complete the user registration upon receiving an InviteMessage. In simple terms, I have: User misc user fields (email, pw, dateJoined) Entity (large professional dataset): personalDetails... user->User (may be null) UserMessage: sender->User recipient->User dateCreated messageContent, other fields..... InviteMessage: sender->User recipient->Entity expiringUrl inviteeEmail inviteePhone I plan to alert the user when selecting a recipient that is not registered yet, and inform that he may send the message as an invitation by providing email, phone where we can send the invitation. Invitations will have a unique, one-time-use URL, e.g. uuid.uuid4(). When accessed, the invitee will see the InviteMessage and details about completing his/her registration profile. When registration is complete, InviteMessage details to a new instance of UserMessage (to not lose their data), and assign it to the newly created User. The ability to interact with and invite persons who do not yet have accounts is a key feature of the application, and it seems better to separate the invitation from the private, app messages (easier to keep functionality separate, better if data model changes). Is this a reasonable, good design? If not, what would you suggest? Do you have any improvements? Am I correct to choose to create a separate endpoint for creating invitations via the API?

  Read the article

• Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

  - by new_bie

  Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

  Read the article

• Why is Mac OS X 10.6 using /usr/lib to start Apache when I compiled PHP using /opt/local/lib?

  - by Anthony

  PHP 5.3.3 compiled on Mac OS X 10.6 - using /usr/lib when trying to start Apache... rather than /opt/local/lib specified when PHP was configured. Why is it trying to load from /usr/lib when I specified in my configure not to? httpd: Syntax error on line 115 of /private/etc/apache2/httpd.conf: Cannot load /usr/libexec/apache2/libphp5.so into server: dlopen(/usr/libexec/apache2/libphp5.so, 10): Library not loaded: /opt/local/lib/libiconv.2.dylib\n Referenced from: /usr/libexec/apache2/libphp5.so\n Reason: Incompatible library version: libphp5.so requires version 8.0.0 or later, but libiconv.2.dylib provides version 7.0.0 The error message above refers to /opt/local/lib which when I run: otool -LD /opt/local/lib/libiconv.2.dylib Message: /opt/local/lib/libiconv.2.dylib: /opt/local/lib/libiconv.2.dylib (compatibility version 8.0.0, current version 8.0.0) /usr/lib/libSystem.B.dylib (compatibility version 1.0.0, current version 125.0.0) It shows that the version is different than what httpd is erring out as. I have a feeling I need to recompile Apache using newer libraries, but the error message still doesn't make too much sense to me.

  Read the article

• Nautilus crashes after Ubuntu Tweak Package Cleaner

  - by Ka7anax

  Few days ago I started having some problems with nautilus. Basically when I'm trying to get into a folder it crashes. It's not happening all the time, but in 85% it does... Sometimes, after the crash all my desktop icons are also gone. The only thing that I think causes this is Ubuntu Tweak - I'm not sure, but the issues started after I did the Package cleaner from Ubuntu Tweaks... Any ideas? -------- EDIT ---------- First time, after running the command (nautilus --quit; nautilus --no-desktop) 3 times all the system crashed (except the mouse, I could move the mouse). After restart I run it and obtain this: ----- Initializing nautilus-gdu extension Initializing nautilus-dropbox 0.6.7 (nautilus:2966): GConf-CRITICAL **: gconf_value_free: assertion value != NULL' failed (nautilus:2966): GConf-CRITICAL **: gconf_value_free: assertionvalue != NULL' failed Nautilus-Share-Message: Called "net usershare info" but it failed: 'net usershare' returned error 255: net usershare: cannot open usershare directory /var/lib/samba/usershares. Error No such file or directory Please ask your system administrator to enable user sharing. and then this: cristi@cris-laptop:~$ nautilus --quit; nautilus --no-desktop (nautilus:3810): Unique-DBus-WARNING **: Error while sending message: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.

  Read the article

• What does 'http: getaddrinfo*.gaih_getanswer: got type "46"' mean

  - by koffie

  Today I got an e-mail from logcheck informing me that the following system event occurred. http: getaddrinfo*.gaih_getanswer: got type "46" Indeed, the above message occurs 4 times in /var/log/aut.log it occured twice yesterday around 6:46 am. And this morning it also occured twice around the same time. I wonder what this message means and if this message is something to worry about or if should just tell logcheck to ignore it. If it is something to worry about, then any pointers on how to fix the problem are appreciated.

  Read the article

• rEFIt can't sync GPT and MBR after resizing boot camp partition

  - by benwad

  I've been trying to follow the instructions here to increase the size of my boot camp partition: http://plonsdale.wordpress.com/2011/06/24/tech-tip-increasing-the-size-of-a-bootcamp-partition-with-free-tools/ I got as far as step 3 when I booted from the rEFIt CD. I selected the partitioning tool and it gave me the following message: Error: Not Found returned from gptsync.efi Now the Windows boot camp partition doesn't show up when I hold alt when starting my mac. Trying to boot into Windows using the rEFIt CD gives me a message saying no Windows installation is found. I then booted off the Windows 7 install CD and the 'repair' option gave me this message: This version of System Recovery Options is not compatible with the version of Windows you are trying to repair. Try using a recovery disc that is compatible with this version of Windows ...and if I try and go install a fresh version of Windows on this partition using the 'Custom (advanced)' option I get an error about the partition saying: Windows cannot be installed to this disk. The selected disk is of the GPT partition style

  Read the article

• Distributed transactions and queues, ruby, erlang

  - by chrispanda

  I have a problem that involves several machines, message queues, and transactions. So for example a user clicks on a web page, the click sends a message to another machine which adds a payment to the user's account. There may be many thousands of clicks per second. All aspects of the transaction should be fault tolerant. I've never had to deal with anything like this before, but a bit of reading suggests this is a well known problem. So to my questions. Am I correct in assuming that secure way of doing this is with a two phase commit, but the protocol is blocking and so I won't get the required performance? It appears that DBs like redis and message queuing system like Rescue, RabbitMQ etc don't really help me a lot - even if I implement some sort of two phase commit, the data will be lost if redis crashes because it is essentially memory-only. All of this has led me to look at erlang - but before I wade in and start learning a new language, I would really like to understand better if this is worth the effort. Specifically, am I right in thinking that because of its parallel processing capabilities, erlang is a better choice for implementing a blocking protocol like two phase commit, or am I confused?

  Read the article

• Writing my first bash script (line 2: testscript: No such file or directory)

  - by skyeagle

  I am attempting to write my first shell script (I'm running Ubuntu 10.x) This is what my 'script' looks like cd /path/to/directory/cronscripts . testscript I put the following debug statements (after the cd), in the script above to make sure everything was ok: pwd echo `ls -lhrt` and it displayed all the files in the directory. So I dont understand the error message I am getting. I have the following two questions Why am I getting the above error message and how do I fix it? My script seems to run fine without a shebang in the first line - infact when I try either of the following: #!/usr/bin/bash #!/usr/bin/bash env I get the following error message: /usr/bin/bash: bad interpreter: No such file or directory What is the purpose of the shebang statement and why do I get the above error when I try to include it in my script/ how do I fix it, so I can add the shebang (is it necessary? - it seems most script examples have the shebang - but I'm not sure if it is a must, as the script runs without it).

  Read the article

• asus n550jv audio problem: no sound from notebook' speakers

  - by skywalker

  Ubuntu 13.10. The problem is: the internal speakers don't work. I have no problem when I'm using the headphones. There is no hardware issue since in windows 8 everything works perfectly(external subwoofer included). I'm trying to modify /etc/modprobe.d/alsa-base.conf but I can't find the correct model to put into: options snd-hda-intel model= The file HD-Audio-Models.txt doesn't contain the model for ALC668. Some info: :~sudo aplay -l **** List of PLAYBACK Hardware Devices **** card 0: MID [HDA Intel MID], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: MID [HDA Intel MID], device 7: HDMI 1 [HDMI 1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: MID [HDA Intel MID], device 8: HDMI 2 [HDMI 2] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: PCH [HDA Intel PCH], device 0: ALC668 Analog [ALC668 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 :~$ sudo lspci -v | grep -A7 -i "audio" 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) Subsystem: Intel Corporation Device 2010 Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at f7a14000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Kernel driver in use: snd_hda_intel -- 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 04) Subsystem: ASUSTeK Computer Inc. Device 11cd Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f7a10000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel PS info :~$ amixer -c 0 Simple mixer control 'IEC958',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] Simple mixer control 'IEC958',1 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] Simple mixer control 'IEC958',2 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] :~$ pacmd dump-volumes Welcome to PulseAudio! Use "help" for usage information. Sink 0: reference = 0: 76% 1: 76%, real = 0: 76% 1: 76%, soft = 0: 100% 1: 100%, current_hw = 0: 76% 1: 76%, save = yes Input 8: volume = 0: 100% 1: 100%, reference_ratio = 0: 100% 1: 100%, real_ratio = 0: 100% 1: 100%, soft = 0: 100% 1: 100%, volume_factor = 0: 100% 1: 100%, volume_factor_sink = 0: 100% 1: 100%, save = no Source 0: reference = 0: 100% 1: 100%, real = 0: 100% 1: 100%, soft = 0: 100% 1: 100%, current_hw = 0: 100% 1: 100%, save = no Source 1: reference = 0: 16% 1: 16%, real = 0: 16% 1: 16%, soft = 0: 100% 1: 100%, current_hw = 0: 16% 1: 16%, save = yes

  Read the article

• Can't get Wireless RT2x00usb driver to work, and can't blacklist it

  - by TheLQ

  After a two year hiatus to Linux, I try it again out again. And then I run into to driver issues... I have an old Linksys WUSB54G v4 Wireless USB Adapter. In previous versions I had to use a combination of Ndiswrapper and Wicd to hope of getting it working. In 10.10, apparently there are built in drivers for it. Unfortunately they don't work. Fails to connect to my WPA network, fails to connect to my open unencrypted network. Wicd fails at "Obtaining IP address" or when using static IPs fails at verifying connectivity to network. Getting fed up I tried the ndiswrapper approach. Installed and configured, but still not working, even when blacklisting the rt2570 module. So for some debugging I added some lines to my /etc/modprobe.d/blacklist.conf file blacklist rt2570 blacklist prism54usb blacklist rt2x00lib blacklist rt2x00usb Restart and find this: lordquackstar@quackbeast:/etc/modprobe.d$ lsmod | grep rt2 rt2500usb 18049 0 rt2x00usb 9779 1 rt2500usb rt2x00lib 27275 2 rt2500usb,rt2x00usb led_class 2633 1 rt2x00lib mac80211 231541 2 rt2x00usb,rt2x00lib cfg80211 144470 2 rt2x00lib,mac80211 Seems to be ignored... Tried this: lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00usb ERROR: Removing 'rt2x00usb': Resource temporarily unavailable lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00lib ERROR: Removing 'rt2x00lib': Resource temporarily unavailable and couldn't connect. Restarted and was back to the same modules loading. Maybe there's something in the log: lordquackstar@quackbeast:/etc/modprobe.d$ tail -n100000 /var/log/syslog | grep rt2 Dec 13 19:01:15 quackbeast kernel: [ 23.698056] Registered led device: rt2500usb-phy0::radio Dec 13 19:01:15 quackbeast kernel: [ 23.698140] Registered led device: rt2500usb-phy0::quality Dec 13 19:01:15 quackbeast kernel: [ 23.701680] usbcore: registered new interface driver rt2500usb Dec 13 19:01:15 quackbeast NetworkManager[855]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Dec 13 19:17:47 quackbeast kernel: [ 23.521759] Registered led device: rt2500usb-phy0::radio Dec 13 19:17:47 quackbeast kernel: [ 23.521824] Registered led device: rt2500usb-phy0::quality Dec 13 19:17:47 quackbeast kernel: [ 23.524740] usbcore: registered new interface driver rt2500usb Dec 13 19:17:47 quackbeast NetworkManager[798]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Seems to be autoloading. So this means that even if I pull it out, remove the module, and get it working, it still won't work when its plugged in all the time. More info: lordquackstar@quackbeast:/etc/modprobe.d$ sudo lshw -C Network *SNIP* *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:12:17:9b:f3:1e capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=2.6.35-24-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg USB: lordquackstar@quackbeast:/etc/modprobe.d$ lsusb | grep -i rt Bus 001 Device 003: ID 13b1:000d Linksys WUSB54G v4 802.11g Adapter [Ralink RT2500USB] Any suggestions on how to either fix the rt2x00usb driver or permanently block it from loading? Note that I already have ndiswrapper installed

  Read the article

• Bluetooth firmware problem in Ubuntu 13.04

  - by chanzerre

  I have a [Dell Inspiron][1] 15R 5520 laptop. Bluetooth is not working at all. rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no dmesg|grep -i bluetooth gives [ 13.644428] Bluetooth: Core ver 2.16 [ 13.644445] Bluetooth: HCI device and connection manager initialized [ 13.644453] Bluetooth: HCI socket layer initialized [ 13.644455] Bluetooth: L2CAP socket layer initialized [ 13.644461] Bluetooth: SCO socket layer initialized [ 15.861363] Bluetooth: hci0 command 0x1003 tx timeout [ 15.903443] Bluetooth: can't load firmware, may not work correctly [ 17.332535] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.332538] Bluetooth: BNEP filters: protocol multicast [ 17.332544] Bluetooth: BNEP socket layer initialized [ 17.393768] Bluetooth: RFCOMM TTY layer initialized [ 17.393781] Bluetooth: RFCOMM socket layer initialized [ 17.393783] Bluetooth: RFCOMM ver 1.11 hciconfig gives hci0: Type: BR/EDR Bus: USB BD Address: E0:06:E6:D5:DB:46 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:687 acl:0 sco:0 events:56 errors:0 TX bytes:2024 acl:0 sco:0 commands:52 errors:0 I have visited the site http://wireless.kernel.org/en/users/Drivers/b43 and according to it lspci -vnn -d 14e4: gives 08:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) Subsystem: Dell Wireless 1704 802.11n + BT 4.0 [1028:0016] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1500000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: wl So I got my PCI-ID as 14e4:4365 which it says is not supported. The alternative is wl. What should I do? My Wi-Fi is working normally without any problems, but Bluetooth is not working. sudo dpkg -i wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb gives following error (Reading database ... 208543 files and directories currently installed.) Unpacking wireless-bcm43142-dkms (from wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb) ... Setting up wireless-bcm43142-dkms (6.20.55.19-1) ... Loading new wireless-bcm43142-6.20.55.19 DKMS files... Building only for 3.8.0-23-generic Building initial module for 3.8.0-23-generic Traceback (most recent call last): File "/usr/share/apport/package-hooks/dkms_packages.py", line 22, in <module> import apport ImportError: No module named apport Error! Bad return status for module build on kernel: 3.8.0-23-generic (x86_64) Consult /var/lib/dkms/wireless-bcm43142/6.20.55.19/build/make.log for more information.

  Read the article

< Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >