Search Results

Search found 5530 results on 222 pages for 'wifi direct'.

Page 149/222 | < Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >

  • Is encryption really needed for having network security? [closed]

    - by Cawas
    I welcome better key-wording here, both on tags and title. I'm trying to conceive a free, open and secure network environment that would work anywhere, from big enterprises to small home networks of just 1 machine. I think since wireless Access Points are the most, if not only, true weak point of a Local Area Network (let's not consider every other security aspect of having internet) there would be basically two points to consider here: Having an open AP for anyone to use the internet through Leaving the whole LAN also open for guests to be able to easily read (only) files on it, and even a place to drop files on Considering these two aspects, once everything is done properly... What's the most secure option between having that, or having just an encrypted password-protected wifi? Of course "both" would seem "more secure". But it shouldn't actually be anything substantial. I've always had the feeling using any kind of the so called "wireless security" methods is actually a bad design. I'm talking mostly about encrypting and pass-phrasing (which are actually two different concepts), since I won't even consider hiding SSID and mac filtering. I understand it's a natural way of thinking. With cable networking nobody can access the network unless they have access to the physical cable, so you're "secure" in the physical way. In a way, encrypting is for wireless what building walls is for the cables. And giving pass-phrases would be adding a door with a key. So, what do you think?

    Read the article

  • Software Diagnostics Tool recommendations for Debugging a Windows 8 freeze

    - by Stuart
    I've had my HP Pavillion dv6 laptop since last November - and it has had 8GB RAM and a 256GB Crucial M4 SSD installed since the start. I use it for software development and it's had a Windows 8 RTM installation since early September. Yesterday I had to give a presentation at a customer site - so used Powerpoint for the first time since installing Win8... since that point my machine has 'frozen' every 2 hours or so after startup. There doesn't seem to be any easy to see reason behind the freeze - the system just freezes, even if I have left it idle with just a desktop there. My immediate suspicion is that the SSD is the mostly likely cause of the problem. I've looked at some of the questions on here - e.g. How do I troubleshoot hardware issues related to a computer freeze/crash? - but don't really want to start taking my laptop apart. Another suspicion is that this might be related to the WiFi adapter (Broadcom 802.11n) since I have noticed that this doesn't seem to play perfectly with things like Hyper-V in Win8. Can anyone recommend any software diagnostic tools that I can run in order to evaluate the health of the SSD or of other parts of the system? Thanks Stuart P.S. I doubt Powerpoint is the cause of this, but I may use it as an excuse never to use it again... More realistically perhaps something got damaged during travel to the customer site?

    Read the article

  • How do i set up a fully featured small business network?

    - by JoshReedSchramm
    This has the possibility to be a very large question but I recently acquired a few rack mount servers and the hardware necessary to run them. Unfortunately I'm a programmer with very little understanding of how to set up a good working network so I'm hoping someone on here might be able to help. What I want to do is run a domain with a series of subdomains which would all be externally accessible. The setup would live inside my home and my internet connection is your run of the mill cable model (which means a dynamic IP) I want to be able to set up a couple site, specifically: www.mycompany.com (mycompany.com with no subdomain would redirect to this) build.mycompany.com (for my continuous integration server) ruby.mycompany.com (for ruby projects) win.mycompany.com (for windows project) etc. Additionally this is still my home network so our personal machines need to be able to get on via wifi with at least the same security we have now through an out of the box router from best buy. I'm thinking i need a DNS server, DHCP server and one of those would run either no-ip or dyndns to accommodate the dynamic ip. I don't necessarily need mail but it might be helpful to have some sort of mail server i could use for testing, it doesn't need to get out to the greater internet though. So how do i set up this kinda of network? tl;dr Need to know how to set up your standard office style network in my home off my normal consumer level cable modem connection.

    Read the article

  • MINSCN?Cache Fusion Read Consistent

    - by Liu Maclean(???)
    ????? ???Ask Maclean Home ???  RAC ? Past Image PI????, ?????????,???11.2.0.3 2 Node RAC??????????: SQL> select * from v$version; BANNER -------------------------------------------------------------------------------- Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production PL/SQL Release 11.2.0.3.0 - Production CORE 11.2.0.3.0 Production TNS for Linux: Version 11.2.0.3.0 - Production NLSRTL Version 11.2.0.3.0 - Production SQL> select * from global_name; GLOBAL_NAME -------------------------------------------------------------------------------- www.oracledatabase12g.com SQL> drop table test purge; Table dropped. SQL> alter system flush buffer_cache; System altered. SQL> create table test(id number); insert into test values(1); insert into test values(2); commit; /* ???? rowid??TEST????2????????? */ select dbms_rowid.rowid_block_number(rowid),dbms_rowid.rowid_relative_fno(rowid) from test; DBMS_ROWID.ROWID_BLOCK_NUMBER(ROWID) DBMS_ROWID.ROWID_RELATIVE_FNO(ROWID) ------------------------------------ ------------------------------------                                89233                                    1                                89233                                    1 SQL> alter system flush buffer_cache; System altered. Instance 1 Session A ??UPDATE??: SQL> update test set id=id+1 where id=1; 1 row updated. Instance 1 Session B ??x$BH buffer header?? ?? ??Buffer??? SQL> select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0;      STATE CR_SCN_BAS ---------- ----------          1          0          3    1227595 X$BH ??? STATE????Buffer???, ???????: STATE NUMBER KCBBHFREE 0 buffer free KCBBHEXLCUR 1 buffer current (and if DFS locked X) KCBBHSHRCUR 2 buffer current (and if DFS locked S) KCBBHCR 3 buffer consistant read KCBBHREADING 4 Being read KCBBHMRECOVERY 5 media recovery (current & special) KCBBHIRECOVERY 6 Instance recovery (somewhat special) ????????????? : state =1 Xcurrent ? state=2 Scurrent ? state=3 CR ??? Instance 2  ?? ????????????? ,???? gc current block 2 way  ??Current Block ??? Instance 2, ?? Instance 1 ??”Current Block” Convert ? Past Image: Instance 2 Session C SQL> update test set id=id+1 where id=2; 1 row updated. Instance 2 Session D SQL> select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0; STATE CR_SCN_BAS ---------- ---------- 1 0 3 1227641 3 1227638 STATE =1 ?Xcurrent block???? Instance 2 , ??? Instance 1 ??? GC??: Instance 1 Session B SQL> select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0;      STATE CR_SCN_BAS ---------- ----------          3    1227641          3    1227638          8          0          3    1227595 ???????, ??????Instance 1??session A????TEST??SELECT??? ,????? 3? State=3?CR ? ??????1?: Instance 1 session A ?????UPDATE? session SQL> alter session set events '10046 trace name context forever,level 8:10708 trace name context forever,level 103: trace[rac.*] disk high'; Session altered. SQL> select * from test;         ID ----------          2          2 select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0;       STATE CR_SCN_BAS ---------- ----------          3    1227716          3    1227713          8          0 ?????????v$BH ????CR????,?????SELECT??? CR????????,???????? ?????????? ??X$BH?????? , ?????CR??SCN Version???: 1227641?1227638?1227595, ?SELECT?????? 2???SCN version?CR? 1227716? 1227713 ???, Oracle????????? ?????????SELECT??????event 10708? rac.*???TRACE,??????TRACE??: PARSING IN CURSOR #140444679938584 len=337 dep=1 uid=0 oct=3 lid=0 tim=1335698913632292 hv=3345277572 ad='bc0e68c8' sqlid='baj7tjm3q9sn4' SELECT /* OPT_DYN_SAMP */ /*+ ALL_ROWS IGNORE_WHERE_CLAUSE NO_PARALLEL(SAMPLESUB) opt_param('parallel_execution_enabled', 'false') NO_PARALLEL_INDEX(SAMPLESUB) NO_SQL_TUNE */ NVL(SUM(C1),0), NVL(SUM(C2),0) FROM (SELECT /*+ NO_PARALLEL("TEST") FULL("TEST") NO_PARALLEL_INDEX("TEST") */ 1 AS C1, 1 AS C2 FROM "SYS"."TEST" "TEST") SAMPLESUB END OF STMT PARSE #140444679938584:c=1000,e=27630,p=0,cr=0,cu=0,mis=1,r=0,dep=1,og=1,plh=1950795681,tim=1335698913632252 EXEC #140444679938584:c=0,e=44,p=0,cr=0,cu=0,mis=0,r=0,dep=1,og=1,plh=1950795681,tim=1335698913632390 *** 2012-04-29 07:28:33.632 kclscrs: req=0 block=1/89233 *** 2012-04-29 07:28:33.632 kclscrs: bid=1:3:1:0:7:80:1:0:4:0:0:0:1:2:4:1:26:0:0:0:70:1a:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:4:3:2:1:2:0:3f:0:1c:86:2d:4:0:0:0:0:a2:3c:7c:b:70:1a:0:0:0:0:1:0:7a:f8:76:1d:1:2:dc:5:a9:fe:17:75:0:0:0:0:0:0:0:0:0:0:0:0:63:e5:0:0:0:0:0:0:10:0:0:0 2012-04-29 07:28:33.632578 : kjbcrc[0x15c91.1 76896.0][9] 2012-04-29 07:28:33.632616 : GSIPC:GMBQ: buff 0xba1e8f90, queue 0xbb79f278, pool 0x60013fa0, freeq 1, nxt 0xbb79f278, prv 0xbb79f278 2012-04-29 07:28:33.632634 : kjbmscrc(0x15c91.1)seq 0x2 reqid=0x1c(shadow 0xb4bb4458,reqid x1c)mas@2(infosz 200)(direct 1) 2012-04-29 07:28:33.632654 : kjbsentscn[0x0.12bbc1][to 2] 2012-04-29 07:28:33.632669 : GSIPC:SENDM: send msg 0xba1e9000 dest x20001 seq 24026 type 32 tkts xff0000 mlen x17001a0 2012-04-29 07:28:33.633385 : GSIPC:KSXPCB: msg 0xba1e9000 status 30, type 32, dest 2, rcvr 1 *** 2012-04-29 07:28:33.633 kclwcrs: wait=0 tm=689 *** 2012-04-29 07:28:33.633 kclwcrs: got 1 blocks from ksxprcv WAIT #140444679938584: nam='gc cr block 2-way' ela= 689 p1=1 p2=89233 p3=1 obj#=76896 tim=1335698913633418 2012-04-29 07:28:33.633490 : kjbcrcomplete[0x15c91.1 76896.0][0] 2012-04-29 07:28:33.633510 : kjbrcvdscn[0x0.12bbc1][from 2][idx 2012-04-29 07:28:33.633527 : kjbrcvdscn[no bscn <= rscn 0x0.12bbc1][from 2] *** 2012-04-29 07:28:33.633 kclwcrs: req=0 typ=cr(2) wtyp=2hop tm=689 ??TRACE???? ?????????TEST??????, ???????Dynamic Sampling?????,???????TEST?? CR???,???????’gc cr block 2-way’ ??: 2012-04-29 07:28:33.632654 : kjbsentscn[0x0.12bbc1][to 2] 12bbc1= 1227713  ???X$BH????CR???,kjbsentscn[0x0.12bbc1][to 2] ????? ? Instance 2 ???SCN=12bbc1=1227713   DBA=0x15c91.1 76896.0 ?  CR Request(obj#=76896) ??kjbrcvdscn????? [no bscn <= rscn 0x0.12bbc1][from 2] ,??? ??receive? SCN Version =12bbc1 ???Best Version CR Server Arch ??????????????????SELECT??: PARSING IN CURSOR #140444682869592 len=18 dep=0 uid=0 oct=3 lid=0 tim=1335698913635874 hv=1689401402 ad='b1a188f0' sqlid='c99yw1xkb4f1u' select * from test END OF STMT PARSE #140444682869592:c=4999,e=34017,p=0,cr=7,cu=0,mis=1,r=0,dep=0,og=1,plh=1357081020,tim=1335698913635870 EXEC #140444682869592:c=0,e=23,p=0,cr=0,cu=0,mis=0,r=0,dep=0,og=1,plh=1357081020,tim=1335698913635939 WAIT #140444682869592: nam='SQL*Net message to client' ela= 7 driver id=1650815232 #bytes=1 p3=0 obj#=0 tim=1335698913636071 *** 2012-04-29 07:28:33.636 kclscrs: req=0 block=1/89233 *** 2012-04-29 07:28:33.636 kclscrs: bid=1:3:1:0:7:83:1:0:4:0:0:0:1:2:4:1:26:0:0:0:70:1a:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:4:3:2:1:2:0:2:0:1c:86:2d:4:0:0:0:0:a2:3c:7c:b:70:1a:0:0:0:0:1:0:7d:f8:76:1d:1:2:dc:5:a9:fe:17:75:0:0:0:0:0:0:0:0:0:0:0:0:63:e5:0:0:0:0:0:0:10:0:0:0 2012-04-29 07:28:33.636209 : kjbcrc[0x15c91.1 76896.0][9] 2012-04-29 07:28:33.636228 : GSIPC:GMBQ: buff 0xba0e5d50, queue 0xbb79f278, pool 0x60013fa0, freeq 1, nxt 0xbb79f278, prv 0xbb79f278 2012-04-29 07:28:33.636244 : kjbmscrc(0x15c91.1)seq 0x3 reqid=0x1d(shadow 0xb4bb4458,reqid x1d)mas@2(infosz 200)(direct 1) 2012-04-29 07:28:33.636252 : kjbsentscn[0x0.12bbc4][to 2] 2012-04-29 07:28:33.636358 : GSIPC:SENDM: send msg 0xba0e5dc0 dest x20001 seq 24029 type 32 tkts xff0000 mlen x17001a0 2012-04-29 07:28:33.636861 : GSIPC:KSXPCB: msg 0xba0e5dc0 status 30, type 32, dest 2, rcvr 1 *** 2012-04-29 07:28:33.637 kclwcrs: wait=0 tm=865 *** 2012-04-29 07:28:33.637 kclwcrs: got 1 blocks from ksxprcv WAIT #140444682869592: nam='gc cr block 2-way' ela= 865 p1=1 p2=89233 p3=1 obj#=76896 tim=1335698913637294 2012-04-29 07:28:33.637356 : kjbcrcomplete[0x15c91.1 76896.0][0] 2012-04-29 07:28:33.637374 : kjbrcvdscn[0x0.12bbc4][from 2][idx 2012-04-29 07:28:33.637389 : kjbrcvdscn[no bscn <= rscn 0x0.12bbc4][from 2] *** 2012-04-29 07:28:33.637 kclwcrs: req=0 typ=cr(2) wtyp=2hop tm=865 ???, “SELECT * FROM TEST”??????’gc cr block 2-way’??:2012-04-29 07:28:33.637374 : kjbrcvdscn[0x0.12bbc4][from 2][idx 2012-04-29 07:28:33.637389 : kjbrcvdscn[no bscn ??Foreground Process? Remote LMS??got?? SCN=1227716 Version?CR, ??? ?????X$BH ?????scn??? ??????????Instance 1????2?SCN???CR?, ???????????Instance 1 Buffer Cache?? ??SCN Version ???CR ??????? ?????????: SQL> alter system set "_enable_minscn_cr"=false scope=spfile; System altered. SQL> alter system set "_db_block_max_cr_dba"=20 scope=spfile; System altered. SQL> startup force; ORA-32004: obsolete or deprecated parameter(s) specified for RDBMS instance ORACLE instance started. Total System Global Area 1570009088 bytes Fixed Size 2228704 bytes Variable Size 989859360 bytes Database Buffers 570425344 bytes Redo Buffers 7495680 bytes Database mounted. Database opened. ???? “_enable_minscn_cr”=false ? “_db_block_max_cr_dba”=20 ???RAC????, ??????: ?Instance 2 Session C ?update??????? ?????Instance 1 ????? ,????Instance 1?Request CR SQL> update test set id=id+1 where id=2; -- Instance 2 1 row updated. SQL> select * From test; -- Instance 1 ID ---------- 1 2 ??? Instance 1? X$BH?? select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0;  STATE CR_SCN_BAS ---------- ---------- 3 1273080 3 1273071 3 1273041 3 1273039 8 0 SQL> update test set id=id+1 where id=3; 1 row updated. SQL> select * From test; ID ---------- 1 2 SQL> select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0; STATE CR_SCN_BAS ---------- ---------- 3 1273091 3 1273080 3 1273071 3 1273041 3 1273039 8 0 ................... SQL> select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0; STATE CR_SCN_BAS ---------- ---------- 3 1273793 3 1273782 3 1273780 3 1273769 3 1273734 3 1273715 3 1273691 3 1273679 3 1273670 3 1273643 3 1273635 3 1273623 3 1273106 3 1273091 3 1273080 3 1273071 3 1273041 3 1273039 3 1273033 19 rows selected. SQL> select state,cr_scn_bas from x$bh where file#=1 and dbablk=89233 and state!=0; STATE CR_SCN_BAS ---------- ---------- 3 1274993 ????? ???? “_enable_minscn_cr”(enable/disable minscn optimization for CR)=false ? “_db_block_max_cr_dba”=20 (Maximum Allowed Number of CR buffers per dba) 2? ??? ????? Instance 1 ??????????? ?? 19????CR?? “_enable_minscn_cr”?11g??????????,???Oracle????CR????SCN,?Foreground Process Receive????????????(SCN??)?SCN Version CR Block??????CBC?? SCN??????CR? , ?????????Buffer Cache??????? ????SCN Version?CR????,????? ?????????? ?????Snap_Scn ?? SCN?? ?????????Current SCN, ??????CR??????????????????????, ????Buffer Cache? ?????????? CR?????????, ?????? “_db_block_max_cr_dba” ???????, ???????????20 ,??????Buffer Cache?????19????CR?; ???”_db_block_max_cr_dba” ???????6 , ?????Buffer cache????????CR ???????6?? ??”_enable_minscn_cr” ??CR???MINSCN ??????, ?????????CR???????, ????? Foreground Process??????CR Request , ?? Holder Instance LMS ?build?? BEST CR ??, ?????????

    Read the article

  • Wireless driver activation problem in compaq c700 in ubuntu 9.04

    - by Fazil
    I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

    Read the article

  • Website does not resolve in browser but traceroute is successful

    - by Colum
    I am trying to figure out an issue. My internet is working fine, but this one website is not resolving. It works via a proxy, traceroute works: 1 192.168.1.1 (192.168.1.1) 4.205 ms 0.568 ms 0.510 ms 2 * * * 3 67.59.255.13 (67.59.255.13) 10.583 ms 7.949 ms 7.557 ms 4 67.59.255.61 (67.59.255.61) 10.256 ms 9.576 ms 13.083 ms 5 64.15.8.126 (64.15.8.126) 9.943 ms 11.929 ms 11.452 ms 6 64.15.0.217 (64.15.0.217) 14.655 ms 14.092 ms 13.771 ms 7 64.15.0.118 (64.15.0.118) 33.201 ms 34.875 ms 36.544 ms 8 xe-6-0-3.ar1.ord1.us.nlayer.net (69.31.111.169) 34.027 ms 34.957 ms 34.231 ms 9 ae1-30g.cr1.ord1.us.nlayer.net (69.31.111.133) 82.683 ms 35.138 ms 37.592 ms 10 xe-3-0-0.cr2.iad1.us.nlayer.net (69.22.142.26) 41.657 ms 34.063 ms 34.519 ms 11 ae2-30g.ar2.iad1.us.nlayer.net (69.31.31.186) 35.780 ms 36.361 ms 33.968 ms 12 as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 35.086 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.234) 38.031 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 36.833 ms 13 cr1.iad2.inforelay.net (66.231.176.246) 32.595 ms cr2.iad1.inforelay.net (66.231.176.10) 31.771 ms cr1.iad2.inforelay.net (66.231.176.246) 32.622 ms 14 cr1.iad2.inforelay.net (66.231.176.246) 32.956 ms 33.625 ms !X 41.058 ms 15 * cr1.iad2.inforelay.net (66.231.176.246) 35.312 ms !X * 16 * cr1.iad2.inforelay.net (66.231.176.246) 32.814 ms !X * 17 cr1.iad2.inforelay.net (66.231.176.246) 35.459 ms !X * 53.137 ms !X Ping returns this: Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout for icmp_seq 4 Request timeout for icmp_seq 5 Request timeout for icmp_seq 6 But what I can not figure out is why my browsers (Firefox, Safari, Opera) can not resolve the domain. I am on a Wifi connection. What could be the problem? BTW I am on a Mac (10.6.5)

    Read the article

  • Cannot Resolve Host Or Access Website Through Router

    - by Boris_yo
    This is weird. I am on Windows XP with Edimax BR 6204Wg. I have 3 devices - 2 laptops and 1 smartphone. 1st laptop and smartphone are connected through WiFi to router and 2nd laptop is connected through LAN to router. Before firmware upgrade i did not try to access website but after firmware upgrade to latest version: http://www.edimax.eu/en/support_detail.php?pd_id=11&pl1_id=3#02 i had problems resolving host, pinging, tracerting and accessing website. Sometimes ping and tracert work but i cannot access website and sometimes i can access website but ping and tracert do not work. Weird? I downgraded to previous version and no changes. If i can no longer access that website through Internet Explorer, i can access it in Firefox. I tried deleting cookies, clearing cache and that seem not make difference. Switching LAN port did not make difference. When i disconnect router and connect laptop through LAN to internet modem, everything is normal. I tried resetting router, resetting to factory default settings and all did not help. At the moment i can access website on laptop connected through LAN from Firefox and Internet Explorer, but on my smartphone i can access website only with Opera but not with built-in browser and Skyfire. UPDATE: I just could only access with Internet Explorer but not with other browsers on my PC. Minutes later i could access with all browsers. But on smartphone i could only access with Opera and not with other browsers. I am confused. I also determined that sometimes i can access and sometimes can't. What is also weird is that when ping and tracert cannot resolve host, i still am able to access website.

    Read the article

  • Vista laptop 1 connects to network but Vista laptop 2 doesn't

    - by Jaips
    (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

    Read the article

  • OpenVPN with MacOS X Client and same subnets in local and remote net.

    - by Daniel
    I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

    Read the article

  • No headphone or speakers plugged in - Windows 7 issue

    - by Amit Ranjan
    I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

    Read the article

  • Cannot find wireless driver for HP laptop

    - by rodey
    I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

    Read the article

  • Port forwarding + shared connection with Ubuntu

    - by Joey Adams
    Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

    Read the article

  • Tooltips shadow stuck on desktop

    - by faulty
    I tends to get this problem from time to time. The tooltips with a shadow appearing on top of everything. It's the shadow of the tooltips not disappearing after the tooltips disappear. The last one I had the tooltips was from the wifi connection list at the systray. This problem also happen to me on another computer. Both running Win7 with ATI gpu. I found this similar post Menu command stuck on screen but none of the solution helped. In fact the "Fade or slide tooltips into view" has been unchecked from the beginning. Ending task of "dwm.exe" also doesn't help. So far the only way to resolve this by restarting window. I can't post picture yet, so can't show any screenshot. Edit: Just tested a few more trick which doesn't work. Turn of aero Hibernate Switch main display to external display and switch back. Change resolution Edit(heavyd): Here is a screenshot from my machine.

    Read the article

  • Access router set up as a bridge behind another router

    - by Alari Truuts
    I have a problem my ISP is refusing to help me with, even though they put up the whole system. Specifications: There's a Thomson TG784 router through which the internet comes in to the building, Behind that (for some reason) is a Juniper NetScreen 5XT - 105 Firewall/Router? which leads to an AMX nxa-enet24 switch that carries the connections all over the building and a series of Apple AirPorts for wifi. Problem: The first router (Thomson) is required for ipTV (by Elion). The tv or ipTV box has to be connected straight to the Thomson router. My service provider cannot see the Thomson router from their side, but see the Juniper, so we might think the Thomson has been configured as a bridge. I need a way to access the Thomson router and see it's configurations, because currently, when connecting a Samsung tv to that router (with elion app for ipTV viewing) or even a computer, it cannot access the internet and even if it could, it would update the Thomson router software, losing it's configurations which I need to preserve. I'm unable to find out the Thomson routers ip address to connect to it, and when directly conencting with a cat5 cable, it doesn't give me an ip address. Hope someone can show me the correct direction for solving my issue. Thank you all for reading, and I appreciate any help, Alari Truuts

    Read the article

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Cannot Update Adobe Creative Suit

    - by Lynda
    I am attempting to check for updates using the Adobe Application Manager on Windows 8 and I get this error: The update server is not responding. The server might be offline temporarily, or the Internet or firewall settings may be incorrect. I have seen this error before on Windows 7 and remembered that I needed to disable the Microsoft Virtual WiFi Miniport Adapter. I navigated to the correct place but the Miniport Adapter was not there. After a bit of searching across several forums I saw a recommendation to change <logLevel>2</logLevel> to <logLevel>10</logLevel>. I attempted that and again it still did not work. I have also tried disabling my anti-virus protection and disabling Windows Firewall. Neither worked. I am not sure what else to try or do at this point. Are there any other recommendations to solve this issue? Notes: I am running Windows 8 Pro using the Creative Cloud Version of CS6. I check for updates by choosing Help Updates from within any Adobe Application I originally posted this question on the Adobe Forums and received no help there.

    Read the article

  • Why can't I update Adobe Creative Suite?

    - by Lynda
    I am attempting to check for updates using the Adobe Application Manager on Windows 8 and I get this error: The update server is not responding. The server might be offline temporarily, or the Internet or firewall settings may be incorrect. I have seen this error before on Windows 7 and remembered that I needed to disable the Microsoft Virtual WiFi Miniport Adapter. I navigated to the correct place but the Miniport Adapter was not there. After a bit of searching across several forums I saw a recommendation to change <logLevel>2</logLevel> to <logLevel>10</logLevel>. I attempted that and again it still did not work. I have also tried disabling my anti-virus protection and disabling Windows Firewall. Neither worked. I am not sure what else to try or do at this point. Are there any other recommendations to solve this issue? Notes: I am running Windows 8 Pro using the Creative Cloud Version of CS6. I check for updates by choosing Help Updates from within any Adobe Application This issue was not present in Windows 7 before I upgraded to Windows 8 I originally posted this question on the Adobe Forums and received no help there.

    Read the article

  • MacBook Pro Late 2009 SATA Resets, Slowness (Is my motherboard dying on both machines?)

    - by A Student at a University
    My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. Some, but not all, resets correlate with AC power connects and disconnects. I don't think the warnings do. (How do I tell?) What are these errors? What causes them? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16[ 0.792047] ahci 0000:00:0b.0: irq 43 for MSI/MSI-X 02:37:16[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16[ 0.792111] ahci 0000:00:0b.0: setting latency timer to 64 02:37:16[ 0.813473] scsi0 : ahci 02:37:16[ 0.823340] scsi1 : ahci 02:37:16[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16[ 1.229570] ata2.00: configured for UDMA/133 02:37:16[ 1.240120] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.240123] ata2: irq_stat 0x00000040, connection status changed 02:37:16[ 1.240127] ata2: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.240133] ata2: hard resetting link 02:37:16[ 1.260738] ata1.00: configured for UDMA/133 02:37:16[ 1.280111] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.280114] ata1: irq_stat 0x00000040, connection status changed 02:37:16[ 1.280118] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.280122] ata1: hard resetting link 02:37:16[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.994215] ata2.00: configured for UDMA/133 02:37:16[ 1.994220] ata2: EH complete 02:37:16[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 2.090773] ata1.00: configured for UDMA/133 02:37:16[ 2.090778] ata1: EH complete 02:37:16[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16[ 2.091165] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 02:37:16[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16[ 2.091582] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 02:37:16[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25[ 19.641532] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.641532] ata1: irq_stat 0x00000040, connection status changed 02:37:25[ 19.641532] ata1: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.641533] ata1: hard resetting link 02:37:25[ 19.642076] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.642078] ata2: irq_stat 0x00000040, connection status changed 02:37:25[ 19.642081] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.642084] ata2: hard resetting link 02:37:26[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.396697] ata2.00: configured for UDMA/133 02:37:26[ 20.396703] ata2: EH complete 02:37:26[ 20.451491] ata1.00: configured for UDMA/133 02:37:26[ 20.451498] ata1: EH complete 02:37:30[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30[ 24.627236] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:37:30[ 24.627240] ata1: irq_stat 0x00000040, connection status changed 02:37:30[ 24.627242] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.627246] ata1: hard resetting link 02:37:30[ 24.632241] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:30[ 24.632244] ata2: irq_stat 0x00000040, connection status changed 02:37:30[ 24.632247] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.632250] ata2: hard resetting link 02:37:31[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.386782] ata2.00: configured for UDMA/133 02:37:31[ 25.386788] ata2: EH complete 02:37:31[ 25.431668] ata1.00: configured for UDMA/133 02:37:31[ 25.431674] ata1: EH complete 02:45:54[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622568] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:55[ 529.622572] ata1: irq_stat 0x00400040, connection status changed 02:45:55[ 529.622576] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622583] ata1: hard resetting link 02:45:55[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622613] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:55[ 529.622616] ata2: irq_stat 0x00000040, connection status changed 02:45:55[ 529.622620] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622624] ata2: hard resetting link 02:45:56[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.384305] ata2.00: configured for UDMA/133 02:45:56[ 530.384314] ata2: EH complete 02:45:56[ 530.399225] ata1.00: configured for UDMA/133 02:45:56[ 530.399233] ata1: EH complete 02:45:58[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58[ 532.590968] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5840000 action 0xe frozen t4 02:45:58[ 532.590973] ata1: irq_stat 0x00000040, connection status changed 02:45:58[ 532.590977] ata1: SError: { CommWake LinkSeq TrStaTrns DevExch } 02:45:58[ 532.590983] ata1: hard resetting link 02:45:58[ 532.591034] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:45:58[ 532.591037] ata2: irq_stat 0x00000040, connection status changed 02:45:58[ 532.591041] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:58[ 532.591045] ata2: hard resetting link 02:45:59[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.344416] ata2.00: configured for UDMA/133 02:45:59[ 533.344424] ata2: EH complete 02:45:59[ 533.360839] ata1.00: configured for UDMA/133 02:45:59[ 533.360847] ata1: EH complete 02:45:59[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59[ 533.660117] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:59[ 533.660122] ata2: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660126] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660132] ata2: hard resetting link 02:45:59[ 533.660141] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:59[ 533.660143] ata1: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660147] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660151] ata1: hard resetting link 02:46:00[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.416768] ata2.00: configured for UDMA/133 02:46:00[ 534.416777] ata2: EH complete 02:46:00[ 534.431396] ata1.00: configured for UDMA/133 02:46:00[ 534.431401] ata1: EH complete 02:46:03[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03[ 537.585992] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:03[ 537.585996] ata1: irq_stat 0x00000040, connection status changed 02:46:03[ 537.585999] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586002] ata1: hard resetting link 02:46:03[ 537.586028] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:46:03[ 537.586030] ata2: irq_stat 0x00000040, connection status changed 02:46:03[ 537.586033] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586036] ata2: hard resetting link 02:46:04[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.334389] ata2.00: configured for UDMA/133 02:46:04[ 538.334398] ata2: EH complete 02:46:04[ 538.343511] ata1.00: configured for UDMA/133 02:46:04[ 538.343519] ata1: EH complete 02:46:04[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540144] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:46:04[ 538.540148] ata1: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540153] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540159] ata1: hard resetting link 02:46:04[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540207] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:46:04[ 538.540211] ata2: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540215] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540220] ata2: hard resetting link 02:46:05[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.294100] ata2.00: configured for UDMA/100 02:46:05[ 539.294106] ata2: EH complete 02:46:05[ 539.314125] ata1.00: configured for UDMA/100 02:46:05[ 539.314132] ------------[ cut here ]------------ 02:46:05[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05[ 539.314144] Hardware name: MacBookPro5,3 02:46:05[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05[ 539.314224] Call Trace: 02:46:05[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05[ 539.314296] ata1: EH complete 02:46:12[ 547.040091] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 02:46:12[ 547.040098] ata1.00: failed command: IDENTIFY DEVICE 02:46:12[ 547.040106] ata1.00: cmd ec/00:00:00:00:00/00:00:00:00:00/40 tag 0 pio 512 in 02:46:12[ 547.040108] res 40/00:01:00:00:00/00:00:00:00:00/e0 Emask 0x4 (timeout) 02:46:12[ 547.040111] ata1.00: status: { DRDY } 02:46:12[ 547.040117] ata1: hard resetting link 02:46:13[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13[ 547.408430] ata1.00: configured for UDMA/100 02:46:13[ 547.408438] ------------[ cut here ]------------ 02:46:13[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13[ 547.408451] Hardware name: MacBookPro5,3 02:46:13[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13[ 547.408531] Call Trace: 02:46:13[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13[ 547.408620] ata1: EH complete 02:46:13[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13[ 547.738204] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:13[ 547.738208] ata1: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738212] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738218] ata1: hard resetting link 02:46:13[ 547.738262] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:13[ 547.738265] ata2: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738269] ata2: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738274] ata2: hard resetting link 02:46:14[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.486809] ata2.00: configured for UDMA/100 02:46:14[ 548.486818] ata2: EH complete 02:46:14[ 548.498998] ata1.00: configured for UDMA/33 02:46:14[ 548.499004] ata1: EH complete 02:46:18[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18[ 552.529674] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529678] ata1: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529680] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529684] ata1: hard resetting link 02:46:18[ 552.529716] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529718] ata2: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529720] ata2: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529723] ata2: hard resetting link 02:46:19[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.284141] ata2.00: configured for UDMA/100 02:46:19[ 553.284150] ata2: EH complete 02:46:19[ 553.301629] ata1.00: configured for UDMA/33 02:46:19[ 553.301637] ata1: EH complete

    Read the article

  • Windows 7 fails to connect to the internet a few minutes after startup

    - by SageTheGreat
    Problem Earlier today, when I turned on my desktop computer, my internet connection works fine. Cryptocurrency miners connecting and hashing as usual and I can browse websites. But after a few minutes, my miner fails indicating that there is something wrong with my internet connection. Tried refreshing my browser and is stuck at "resolving host", and then presented me an error. After that, i can't browse sites anymore. But the weird thing is that the network icon in Windows 7 shows no signs of problems. Solutions Made Restarted my computer without doing anything: Problem persists. Tried using the network troubleshooter of windows: Reported no problems Stopped bonjour still no progress. Loaded windows using Last good config: still no progress. Restarted Modem: No change. Current Status I currently did a system restore to my system to a point before installing the latest update from Microsoft. Because earlier today, I installed some updates and after that, the problem started to appear. (After system restore, same problem.) Latest Programs installed before the problem MS Visual Studio 2013 (but internet still worked fine after the install). I hope someone could provide answers on this problem. It is my first time encountering this. EDIT: Additional Info OS: Windows 7 SP1 64-bit AV: Avast Free Antivirus Internet Connection Type: Ethernet It appears that my Laptop can't even connect to the machine thru Remote Desktop My laptop and phone on WiFi works fine and can connect to the internet. EDIT 2: Whenever I boot into Safe Mode, my Internet is fine.

    Read the article

  • IPSec tunnelling with ISA Server 2000...

    - by Izhido
    Believe it or not, our corporate network still uses ISA Server 2000 (in a Windows Server 2003 machine) to enable / control Internet access to / from it. I was asked recently to configure that ISA Server to create a site-to-site VPN for a new branch in a office about 25 km. away from it. The idea is basically to enable not only computers, but also Palm devices (WiFi-enabled, of course), to be able to see other computers in both sites. I was also told that a simple VPN-enabled wireless AP/router (in this case, a Cisco WRV210 unit) should be enough to establish communications with the main office. To be fair, the router looks easy to configure; it was confusing at first, but further understanding of how site-to-site VPNs work cleared all doubts about it. Now I need to make modifications to our ISA Server in order to recognize the newly installed & configured "remote" VPN site. Thing is, either my Googling skills are pathethically horrible, or there doesn't seem to be much (or any, at all) information about how to configure an ISA Server 2000 for this purpose. Lots of stuff on 2004, of course; also, I think I saw something for 2006. But nothing I could find about 2000. Reading about 2004, it seems that the only way I can do site-on-site with a Cisco router (read: a non-ISA-Server machine) is through something they call a "IPSec tunnel". Fair enough. However, I can't figure for the life of me how could I even start to find, leave alone configure, such a thing. Do you, people, happen to know how to do IPSec tunelling on a ISA Server 2000, so I can connect to a Cisco WRV210 VPN-enabled router, and build a site-to-site VPN for both networks? Or is this not possible at all? (Meaning I should change anything in this configuration to make it work...)

    Read the article

  • Wireless disconnects every 30 minutes

    - by Kez
    I have had a look through all the related questions and I get the feeling my problem is unique. My wireless connection disconnects every 30 minutes, for maybe 1 to 3 seconds. If I am browsing the web while it happens, I get the page cannot be displayed error message. I have checked the event logs as I was curious to know if there was anything in there. There is. Event 8033: BROWSER - The browser has forced an election on network \Device\NetBT_Tcpip_{B919CC30-25A9-45DD-A09F-549A6262FC9E} because a master browser was stopped. Reported exactly every 30 minutes which coincides with my wireless problem. I am running Windows 7 Ultimate, 32-bit. My wireless is Realtek RTL8187 integrated into a ASUS P5K-E/Wifi motherboard. It is on a workgroup and has never been on a domain. This problem does not affect any other computers. Wireless reception is great, and I have ensured that the wireless unit is transmitting on a frequency not used by any nearby wireless basestations. How can I fix this pesky problem?

    Read the article

  • Cannot find wireless driver for HP laptop

    - by rodey
    I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

    Read the article

  • Wiring my internet

    - by u8sand
    I have Verizon internet service and am currently using wifi. My router is in the basement and my desktop computer is 2 floors and on the other side of the house above it... Worst possible positioning but that's just how things worked out. My wireless currently is extremely unstable so I've decide to correct the problem by wiring my computer directly. The problem lies here: when redoing the room next to it (when the wall was open) we went ahead and wired some coaxial cable from our attic to our basement (with plenty of slack on both ends, don't ask me why we didn't go ahead and wire a CAT6 cable). The question is: Can I use the coaxial cable to bring me internet connection? Naturally the router (which needs to stay where it is) takes a coaxial cable input and has Ethernet outputs. So maybe I would have to take a ethernet cable, convert to coaxial-coaxial to my computer, convert back to ethernet. Is this even possible to convert from coaxial to ethernet? Or do I have to attempt to go ahead and fish a cat6 cable through my house. I cannot just split the signal because that would require two routers and two networks (which I don't believe would work with one cable-one ISP correct me if I'm wrong). Thanks

    Read the article

  • Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

    - by d4ryl3
    I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

    Read the article

< Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >