Search Results

Search found 607 results on 25 pages for 'adapters'.

Page 15/25 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• I'm using a compatible active DisplayPort to DVI adapter with EyeFinity, why does my monitor still flicker?

  - by Christopher Galpin

  I specifically chose an active DisplayPort <- DVI adapter for use with EyeFinity right out of my graphic card vendor's list of confirmed compatible adapters. Yet the screen fails horribly, it blinks on and off constantly, sometimes the graphics go screwy and the appropriate resolutions won't be available. Sometimes the resolution will be available but I'll discover it's only with interlaced refresh rates and bounces up and down. I have to switch the resolution back and forth, again and again, to get it to work correctly, and then it fails again and the process must be repeated the moment the monitor is turned off or I reboot. It's maddening. What is wrong? Is my GFX card supplying insufficient voltage? (Firmware tweaks allegedly help some people, but my card's isn't modifiable.) Could the adapter be defective? Is it not "active" enough for my card and I need an expensive powered adapter? Is this endemic to DisplayPort in general?

  Read the article

• Restart my graphics card without rebooting?

  - by defaye

  Wondered if it is possible to use DevCon to restart a display device as a stop-gap solution to artifacts left over from a graphics card malfunction? In particular it leaves my cursor very un-user-friendly: I found out the hardware ID of my display adapter through device manager (below) [(windows key + pause break) - device manager - display adapters - right click your display adapter - properties - details - hardware ids.] I tried the commands (opened with admin privileges) devcon restart "PCI\VEN_1002" and devcon restart =display but it always come back with No devices restarted.. Is it even possible to restart the graphics card without a system reboot?

  Read the article

• Notebook with NVIDIA Optimus not switching video card in games

  - by user140739

  I have a Samsung RC720 notebook with Intel Integrated Graphics and NVIDIA GeForce GT 520M. As you can see it has two video adapters and Optimus is supposed to switch between them. But when I choose dedicated GPU in NVIDIA Control Panel and try to run, for example, GTA IV, it uses integrated graphics and I get very poor performance. I have already installed last NVIDIA and notebook drivers, chose high-performance in NVIDIA Control Panel, tried to execute with "Run with graphics processor..." context option and so on. Thanks for help.

  Read the article

• Oracle OpenWorld Highlights

  - by Doug Reid

  We are in the final days of Oracle OpenWorld 2012 and the data integration team have been hard at work giving sessions, meeting customers, demonstrating product and conducting hands-on labs.    It has been a great conference, but the best part is meeting our customers and learning about all the great implementations of our products.  Wednesday was the last day that the exhibition hall was open and attendees were getting in their final opportunities to see our products and meet with the product management team.   Two hours before the close of the hall, people lined up to learn about GoldenGate 11gR2, Monitor, Adapters, Veridata, and all the different use cases.    Here's a picture of Sjaak Vossepoel, who is our DIS Sales Consulting Manager for EMEA speaking to a potential customer on the options of using Oracle GoldenGate for heterogenous data replication.  Over the last two days, the GoldenGate team ran two labs; Introduction to Oracle GoldenGate Veridata and Deep Dive into Oracle GoldenGate.   Both of the labs were completely booked out and unfortunately we had to turn away people.   BUT,  all of our labs were recorded recently so if you were not able to get into the lab or did not have enough time to complete your labs, visit youtube.com/oraclegoldengate to see a  complete recording of the labs we used at OpenWorld plus more.  Here are a couple pictures from the Deep Dive into Oracle GoldenGate lead by Chis Lawless from the Product Management team.   Thanks to the GoldenGate Hands-on Lab team for putting on a great session!!! We will post more information about where you can find additional details on OpenWorld as they become public.   

  Read the article

• WebCenter 11.1.1.8 Certified with E-Business Suite 12.2

  - by Steven Chan (Oracle Development)

  Oracle WebCenter Suite is an integrated suite of Fusion Middleware 11gR1 tools used to create web sites and portals using service-oriented architecture (SOA).  Applications adapters are also available. WebCenter Portal 11.1.1.8 is now certified with Oracle E-Business Suite Release 12.2.  This complements our existing certifications of WebCenter Portal 11.1.1.8 with EBS 12.0 and 12.1.  WebCenter Portal 11.1.1.8 is part of Oracle Fusion Middleware 11g Release 1 Version 11.1.1.8.0, also known as FMW 11gR1 Patchset 7.  Certified Platforms Oracle WebCenter Portal is certified to run on any operating system for which Oracle WebLogic Server 11g is certified. For information on operating systems supported by Oracle WebLogic Server 11g and Oracle WebCenter Portal, refer to the 'Oracle Fusion Middleware on WebLogic Server - System Certification' in the Oracle Fusion Middleware 11g Release 1 (11.1.1.x) Certification Matrix. Integration with Oracle WebCenter Portal involves components spanning several different suites of Oracle products. There are no restrictions on which platform any particular component may be installed so long as the platform is supported for that component. Migrating to Oracle WebCenterIf you're currently using Oracle Portal, you should be aware that Portal is now in maintenance mode.  Updates with bug fixes will continue to be produced, but you should consider migrating to Oracle WebCenter for ongoing new features. References Using WebCenter 11.1.1 with Oracle E-Business Suite Release 12.2 (Note 1332645.1) WebCenter Portal 11g Release 1 (11.1.1.8) Documentation Related Articles Oracle E-Business Suite 12.2 Now Available WebCenter Portal 11.1.1.8 Certified with E-Business Suite 12

  Read the article

• Virtualizing Firewalls/UTM

  - by TheD

  So Sophos UTM (Astaro Gateway UTM) can be virtualized in Hyper-V, VMWare, vSphere etc. Now I'm new to virtualization, so am wondering how the networking would be configured in this situation. Imagine the following (a very simple setup). A Zyxel router acting as the default gateway, standard ADSL line. This is connected directly via Ethernet to my VHost, Hyper-V in my case. Now I assume I need two virtual network adapters, one which is the "External" interface to the firewall, and the other being the "Internal" interface. But where does my switch go, since I have 5 machines (or X number of machines). Where is the switch connected, to the internal interface on the VHost? What default gateway do my clients use etc? How would the routing work if these two interfaces weren't bridged since they are virtual networks anyway. I'm a little confused! Any advice is much appreciated! Cheers

  Read the article

• Getting VPN to work from Virtual PC

  - by strobaek

  Setup: Host is running Windows7. Virtual PC is a Windows Server 2008 running under VMWare workstation 6.5. From the Host I have a VPN to e.g. TFS and other resources. From the VPC I need to connect to e.g. a SQL server via the VPN. My problem is, that I cannot get a connection from the VPC. If I'm sitting on the corporate network, all is working fine (but then I don't have the VPN). From home - where the VPN is required - it does not work. I have two network adapters defined/configued. One as BRIDGED and one as Host Only. IF I change the one being BRIDTED to NATS I have no connectivity at all from the VPC. I have no problems connecting from my host to the VPC. Thanks.

  Read the article

• Triple-display setup using AMD drivers

  - by Halik

  I am currently running a dual display setup with nVidia 8800GTS video card, on a Ubuntu 12.10 box. The current setup uses nVidia TwinView to render the image on a 1920x1200 display and 1600x1200 one. I'm planning to add a third, 1280x1024 display to the setup. The change will require me to upgrade my GFX card to one supporting triple displays. I'll probably go with Sapphire Radeon 7770 (FLEX edition, to avoid additional active DP-DVI adapters). Before I invest in new GFX I wanted to ask - how well the AMD drivers will support such a setup. It does not matter whether it's fglrx or the OSS ones. If I remember correctly, when running Fedora on a Radeon x800, I had 'void' areas above and below the working area on my second display. The desktop was rendered in 1920+1280 width and 1200 height (which left 176px of vertical space accessible for my cursor and windows but not displayed on the screen - I'd prefer to avoid that). It may have very well been my misconfiguration back then. Generally, are there any solutions from AMD on par with TwinView? Or is it a non-issue at all? Also, I'm wondering about the usual stuff - hardware h264 decoding support, glitch-free flash support, any issues with Compiz/Unity?

  Read the article

• Scripted SOA Diagnostic Dumps for PS6 (11.1.1.7)

  - by ShawnBailey

  When you upgrade to SOA Suite PS6 (11.1.1.7) you acquire a new set of Diagnostic Dumps in addition to what was available in PS5. With more than a dozen to choose from and not wanting to run them one at a time, this blog post provides a sample script to collect them all quickly and hopefully easily. There are several ways that this collection could be scripted and this is just one example. What is Included: wlst.properties: Ant Properties build.xml soa_diagnostic_script.py: Python Script What is Collected: 5 contextual thread dumps at 5 second intervals Diagnostic log entries from the server WLS Image which includes the domain configuration and WLS runtime data Most of the SOA Diagnostic Dumps including those for BPEL runtime, Adapters and composite information from MDS Instructions: Download the package and extract it to a location of your choosing Update the properties file 'wlst.properties' to match your environment Run 'ant' (must be on the path) Collect the zip package containing the files (by default it will be in the script.output location) Properties Reference: oracle_common.common.bin: Location of oracle_common/common/bin script.home: Location where you extracted the script and supporting files script.output: Location where you want the collections written username: User name for server connection pwd: Password to connect to the server url: T3 URL for server connection, '<host>:<port>' dump_interval: Interval in seconds between thread dumps log_interval: Duration in minutes that you want to go back for diagnostic log information Script Package

  Read the article

• Vista to Vista network visability issue

  - by Sk93

  Hi All, I've got a Vista Business PC and a Vista Business Laptop connected via a virgin media router (Netgear CG2100D) and I cannot get the two machines to see each other correctly over the network. The laptop is connected via wireless, whilst the pc is wired. Both are set to recieve their network settings automatically (DHCP) and both have the windows firewall (the only firewall on either) turned off completely. I can ping each machine fine from one another using the ip addresses, and I can also connect via \. However, connections via \ fail, and I cannot see the machines in the network map. I have tried turning netBIOS to be "always on" on both adapters, but this makes no difference. I've been messing around pretty much for 6 hours now and am getting quite fustrated by this! (my original aim was to get media sharing working, but I've pretty much abandoned that for now). Any ideas?

  Read the article

• How do I configure networking on CentOS 6 running on hyper-v?

  - by LonelyLonelyNetworkN00b

  I'm not using legacy adapters, and i've installed Linux Integration Components 3.2. THe problem i'm facing is that the command 'setup' or 'system-config-network' doesn't list any network interfaces. If i run ifconfig -a i can see both the network cards i've attached. By setting a ip using ifconfig i can get network connectivity. The problem is that it's not persistent after a reboot. I'm a 100% centos newbie, but I figure it has something to do with that the centos installer couldn't see the NICs on install. How can I fix this?

  Read the article

• How do you passthrough native SATA drives to a guest on ESXi?

  - by John

  I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

  Read the article

• Get the interface and ip address used to connect to a specific host (ip)

  - by umop

  I'm sure this has been asked and answered before, but I wasn't able to find it, so hopefully this will at least link someone to the right place. I want to find out my local interface and ip address used to reach a certain host. For instance, if I had 3 adapters connected to my box and they all three went to different networks, I'd like to know which of the three (specifically, its ip address) is used to reach my.local.intranet (in this case, it would be a vpn tunnel interface). I suspect this is a job for ifconfig or traceroute, but I haven't been able to find the correct switches. I'm running OSX 10.7 (Darwin) Thanks!

  Read the article

• Is it safe to use an IDE to SATA power adapter for an extended period of time?

  - by qwertymk

  I just bought a computer from HP and they failed to include SATA power connectors with the power supply other then the one HD and DVD drive. Meanwhile I have two IDE to SATA power adapters that came with my "USB 2.0 to SATA/IDE cable" http://www.amazon.com/USB-2-0-SATA-Cable-Adapter/dp/B001OORN06 3rd pic on the left. I was wondering if I would just open up my computer and use it to plug it my SATA drives to the IDE power sources and mount it to the motherboard, would it damage my drives in the long run or have any other significant effects. A friend told me he knows people who have had their HD burn out because of this

  Read the article

• Welcome!

  - by mannamal

  Welcome to the Oracle Big Data Connectors blog, which will focus on posts related to integrating data on a Hadoop cluster with Oracle Database. In particular the blog will focus on best practices, usage notes, and performance tips for using Oracle Loader for Hadoop and Oracle Direct Connector for HDFS, which are part of Oracle Big Data Connectors. Oracle Big Data Connectors 1.0 also includes Oracle R Connector for Hadoop and Oracle Data Integrator Application Adapters for Hadoop. Oracle Loader for Hadoop: Oracle Loader for Hadoop loads data from Hadoop to Oracle Database. It runs as a MapReduce job on Hadoop to partition, sort, and convert the data into an Oracle-ready format, offloading to Hadoop the processing that is typically done using database CPUs. The data is thenloaded to the database by the Oracle Loader for Hadoop job (online load) or written out as Oracle Data Pump files for load and access later (offline load) with Oracle Direct Connector for HDFS. Oracle Direct Connector for HDFS: Oracle Direct Connector for HDFS is a connector for high speed access of data on HDFS from Oracle Database. With this connector Oracle SQL can be used to directly query data on HDFS. The data can be Oracle Data Pump files generated by Oracle Loader for Hadoop or delimited text files. The connector can also be used to load data into the database using SQL.

  Read the article

• Planning office network [closed]

  - by gakhov

  I'm planning to setup my office network from scratch and want to ask professional opinions or tips. My office is connected to Internet with Cable connection (100Mb/s). The devices i would like to connect are VoIP Phone (RJ-11), TV (WiFi/LAN), 3 laptops (WiFi), a few smartphones (WiFi), iPad (WiFi), Kindle (WiFi) and, probably, MediaServer (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, i need help to choose the best routers combination (or even one?) to support stable connections for all these devices and minimize the total number of routers/adapters. Any thoughts? Thank you!

  Read the article

• Where can I get a splitter to connect a device with a single 3.5 mm plug into the audio input/output jacks on my laptop?

  - by XinJeisan

  I recently bought the :Hype Retro Handset for Mobile Phone" -- its just a device that looks like a handset to use when chatting on a computer or mobile phone that plugs into the phone/computer with a single 3.5 mm plug. I was hoping to use it on my windows 7 Toshiba laptop. I can hear audio fine through the handset but what I'm saying is not being picked up on the handset. On the box it says "some phones and computers may need additional adapters," so I'm hoping it is possible to get a splitter or something for this to work properly. I did email the parent company (http://dglusa.com/) but I haven't heard from them, and, looking over their website, I doubt I will. I also went to the local radio shack, and the guy said I needed a splitter, but he didn't know where to get one. I can find the kind of splitter I think I need online, but I'm unsure whether they are just for output or can also do input/output.

  Read the article

• wireless dropping out

  - by Sam

  My wireless network connection is dropping out and its driving me nuts. It is weird because it happens at totally random intervals and other devices work while my computer has been dropped. Both my USB dongle and wifi card randomly disconnect from the router and I am unable to connect for a couple of minutes. It is especially irritating because two different adapters are failing at the same time, sounds like a software problem to me, but where? Both my laptop and iPod remain connected when the connection drops. What on earth is happening? I doubt its the router because the other devices would disconnect as well.

  Read the article

• Connecting guest OS to host os internet connection hyper-v

  - by autrevo

  Hyper-V internal switch and VM OS interfacing with Guest OS and IP Cofiguration When configuring hyper-v internal switch, Apart from physical lan adapter (say adapter 1), I see another LAN adapter (say adapter 2) added in host os. And we already have one virtual lan adapter in guest os, (say adapter 3) . adapter 1 is connected to internet with defaulty gateway say, 192.168.0.254 and uses class C IP. By con configuring adapter 2 and 3, I need to acheive two purpose - Access internet in guest os. seemlessly share files & folders between guest and host OS. Please, suggest, What is the best way to configure IP of these three adapters ?

  Read the article

• TCP/IP communication between Hyper-V host and guests

  - by Tedd Hansen

  This may be a simple one. :) I have a simple Hyper-V setup with a few guest os running. The host has 1 physical network adapter with a static IP assigned to it. The guests have network adapters assigned to "Internet" (Hyper-V network) which is bound to the physical host network adapter (Hyper-V "External" connection type). I am not able to communicate (ping or anything else) between guests and host. I've checked firewall and it seems fine (ports open from anywhere still don't work). I'm trying to communicate with the hosts IP assigned to the same physical interface that the guests are sharing. Guests can communicate between them just fine. I can't seem to find any relevant setting (I might just be missing it). So my questions: How do I fix it so host and guests can communicate?

  Read the article

• Are there any 17-20 inch monitors that support displayport?

  - by WildJoe

  I've got dual monitors now (both 20 inch 1600x1200). After seeing the new eyefinity cards out there (and reading the CodingHorror post on three monitors) I've decided to get a third. It's time to upgrade my video card anyway. Since I don't already have a third monitor and will be buying one new, I figure it'd make sense to buy one that already had a DisplayPort interface so as to avoid the adapter issue. However, I can't seem to find any monitors on newegg that support this (it's not even an option in the power search, and a keyword search turned up only adapters and video cards). A quick google showed me several 30 inchers (like Dell's, but that's way too expensive, and I don't have that much room on my desk even if I had that money) and some 22 inch models. Again, I'm looking for a 17-20 inch with a DisplayPort interface built in. Any suggestions?

  Read the article

• Installing ethernet controller driver after clean windows XP install

  - by user1488804

  I've been having trouble getting internet access through an ethernet connection since doing a fresh install of windows XP. It appears that I'm missing the driver for the ethernet controller. Looking in 'device manager' under the network adapters section there's an apparently working '1394 Net Adaptor' but under unknown devices there's the question-marked ethernet controller, which I believe is what I want the driver for. I found an old cd that contains the driver for it (Realtek 8139 or some 81xx). There's no setup tool, but only 3 files (a .cat file, .inf file and .sys file). I've tried right-clicking on the .inf file and using 'install' and also tried just copying the .sys file into the system32/drivers folder but neither have got me anywhere after restarting. The ethernet controller is still listed in 'unknown devices'. EDIT: I've also tried updating the driver in the device manager, pointing it at the folder containing the driver, but this hasn't worked either. Any ideas? Thanks

  Read the article

• How to really change programmatically ip address without reboot (with no connection too)?

  - by DmitryI

  Really, I tried everything, and there is no solution that works for me. WMI - everything perfect, but I can't change ip address when there is no connection. O_o Are you joking me? How can I make a connection without correct Ip-address? IPHelper - not doing anything. Just adding address to the table. Not work after reboot. netsh - the stupid way I think, but ok, if you don't no another ways you can try. Before you will know, that network adapters name can contain international characters. Did someone know how it works actually, I mean inside? Registry - working after reboot. I don't want to reboot. May be someone know how to notify about reg entries changes?

  Read the article

• What is this thing called?

  - by Portman

  (Original title: "WTF is this thing called?") I have a couple of networking components in my rack that take giant AC adapters ("power bricks") that don't fit neatly into my rackmount PDU. I have one "thingy" that is shown below, and I need to buy a few more. But I have no idea what I'm searching for because I don't know what the "thingy" is called. Yes, this drawing is terrible. I would ask my 4-year-old to draw it for me because she's a better artist, but she's taking a nap.

  Read the article

• What's the point of the Prototype design pattern?

  - by user1905391

  So I'm learning about design patterns in school. Many of them are silly little ideas, but nevertheless solve some recurring problems(singleton, adapters, asynchronous polling, ect). But today I was told about the so called 'Prototype' design pattern. I must be missing something, because I don't see any benefits from it. I've seen people online say it's faster than using "new"' but this is doesn't make any sense, since at some point, regardless how the new object is created, memory needs to be allocated for it ect. Furthermore, doesn't this pattern run in the same circles as the 'chicken or egg' problem? By this I mean, since the prototype pattern essentially is just cloning objects, at some point the original object must be created itself (ie, not cloned). So this would mean, that I would need to have an existing copy of every object that I would ever want to clone already ready to clone? Seems stupid to me. Can anyone explain what the use of this pattern is? Original post: http://stackoverflow.com/questions/13887704/whats-the-point-of-the-prototype-design-pattern

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >