Search Results

Search found 408 results on 17 pages for 'broadcom'.

Page 15/17 | < Previous Page | 11 12 13 14 15 16 17  | Next Page >

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• Distribute IP packets accross different NIC queues with MSI (Message Signalled Interrupts)

  - by Ansis Atteka

  NetXtreme II BCM5709 Gigabit Ethernet NIC supports MSI feature (Message Signaled Interrupts) and it has 8 queues. Each queue has its own Interrupt handler in /proc/interrupts. What I am trying to accomplish is to tell NIC which packets should go to which queue. Questions: Is it possible to manually specify which IP packets should go to which queue by encapsulated protocol type (e.g. IPsec packets go in one queue, while TCP packets go in another queue)? If it is possible - how can I do it under Linux? If it is not possible - should I look at MSI-X capable NIC cards to solve this problem? More details: We have one Interface that is terminating IPSec and forwarding/terminating TCP connections. The IPSec packet decryption is inlined (this means that decryption is done under the same ksoftirqd/X context). We are trying to find out if we will be able to improve total performance if IPSec packets will be scheduled on another CPU than TCP packets. One more limitation is that IPSec code is not MP-safe, hence I can not run it under more than one ksoftirqd/X. By default it seems that packets are distributed/hashed by source IP over the 8 NIC queues. The bottleneck is IPSec that chokes out TCP traffic while it is decrypting/encrypting IPSec packets at ~100% CPU. OS is Ubuntu 10.10 (2.6.32-27-server) and NIC is Broadcom BCM5709.

  Read the article

• How to use my computer as a Headset device for my phone with Bluetooth?

  - by TheJelly

  I want to extract the audio from my phone (the analog TV and FM/AM receiver mainly) and play it through my computer speakers. There is a headphone jack but it is of non-standard size (probably a micro-jack) and I do not have access to a shop that sells that kind of equipment in my area so doing this with Bluetooth is the only solution I can foresee. Both my laptop and my phone support A2DP but for some reason the service (from the phone) does not show up while I add a new connection and the phone does not let me initiate a connection with any other profile except FTP (although it detects other services in the service list like A2DP and works perfectly fine with other profiles like DUN, HID, OPP, SSP if the connection is started through the computer). I am currently using the latest version of the Toshiba stack, I have tried using WIDCOMM but it refuses to install drivers for both the internal Bluetooth (which is a Broadcom device) and the USB Bluetooth that I use on my desktop. The standard Microsoft stack (generic driver) does install but it does not work with both of my devices as they do not detect any Bluetooth devices when scanning. With BlueSoleil (the default stack that came with the USB Bluetooth) I could set my device as "headset" instead of only "laptop/desktop", and this allowed both my phones to detect my laptop as a device they can use as a headset, but the problem with this stack was that only the older phone could actually connect to my laptop and that the internal Bluetooth could not be used. Basically, I want to set the device type as a "headset" for my phone using the Toshiba stack like I did with BlueSoleil. Is there any way this could be done? Thanks. Image: Device type selection http://i.stack.imgur.com/drjC6.jpg

  Read the article

• Why would Windows use slower network interface despite route metrics?

  - by tim11g

  On my previous notebook, the Dell/Broadcom wireless adapter had an option to automatically disable wireless when a wired network is connected, so I never dealt with multiple active interfaces. My current system has an Intel wireless adapter, and they apparently haven't figured out how to turn it off when there is a wired connection. Unless I explicitly remember to disable wireless when docked, the connection is active. That shouldn't be a problem (in theory), since the route metric will cause traffic to go over the fastest network (as indicated by the lowest metric in the routing table). Apparently not - I'm running a backup and seeing the throughput at 25Mbps or so (which is consistent with 802.11g) when a perfectly good Gigabit Ethernet interface is also connected. IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.104 10 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.109 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 Windows has correctly identified the Ethernet interface (.104) and assigned it the lower (preferred) metric. So the Ethernet interface should be used exclusively, right? Why is the Ethernet connection not being used? What other factors are involved? (This is with Windows 7 if it makes a difference)

  Read the article

• Windows 8 & Hyper-V Can't Bridge Wifi Connection

  - by xinunix

  So I have an odd issue that I can't quite figure out... I am running Windows 8 Enterprise on a Dell 6420 laptop. I have a Broadcom 802.11n wireless adapter. I am connected to an home router (Netgear WNDR3700) that is connected to the internet. It is a very simple home network setup. I am trying to stand-up a few VMs in Hyper-V and want the VMs to be able to access the internet over my wireless connection. I have found numerous examples of how to set this up using both External and Internal Virtual Switches but have yet to be able to get it to work on my machine. I have narrowed the issue down to the fact that my host machine always loses internet connection when I bridge my wifi connection (both when it is bridged automatically by windows when I setup an external virtual switch bound to the wifi adapter or if I do it manually by creating an internal virtual switch, right click on it and my wifi network and select "Bridge Connections".) In both cases after the bridge is established, my host machine can no longer connect to the internet. I am not sure where to start with troubleshooting this problem. After the bridge is setup, an ipconfig shows all netowrk devices on the machine as "Media Disconnected". I do know that the wireless adapter is connected to the router b/c it shows the connection as active and full-strength. The only thing I can possibly think of is that this machine also has the Cisco VPN client installed on it which installs a Cisco Virtual Network Adapter. Is it possible that this Cisco Virtual Adapter is causing me issues when I try to bridge? I saw some people had a similar issue with a VirtualBox virtual adapter when trying to share via Hyper-V. Any thoughts or suggestions on how to troubleshoot?

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• Software Diagnostics Tool recommendations for Debugging a Windows 8 freeze

  - by Stuart

  I've had my HP Pavillion dv6 laptop since last November - and it has had 8GB RAM and a 256GB Crucial M4 SSD installed since the start. I use it for software development and it's had a Windows 8 RTM installation since early September. Yesterday I had to give a presentation at a customer site - so used Powerpoint for the first time since installing Win8... since that point my machine has 'frozen' every 2 hours or so after startup. There doesn't seem to be any easy to see reason behind the freeze - the system just freezes, even if I have left it idle with just a desktop there. My immediate suspicion is that the SSD is the mostly likely cause of the problem. I've looked at some of the questions on here - e.g. How do I troubleshoot hardware issues related to a computer freeze/crash? - but don't really want to start taking my laptop apart. Another suspicion is that this might be related to the WiFi adapter (Broadcom 802.11n) since I have noticed that this doesn't seem to play perfectly with things like Hyper-V in Win8. Can anyone recommend any software diagnostic tools that I can run in order to evaluate the health of the SSD or of other parts of the system? Thanks Stuart P.S. I doubt Powerpoint is the cause of this, but I may use it as an excuse never to use it again... More realistically perhaps something got damaged during travel to the customer site?

  Read the article

• Network access lags for Win7 when server network utilization is high

  - by Jeff Miles

  We have a Dell PE2950 file server running Windows 2008, hosting a DFS namespace of ~1.2 TB. This server has two Broadcom 1Gbps NICs teamed together. When there is high traffic going to the server across the network (greater than 200 Mbps), any Windows 7 client accessing a DFS share at the time experiences severe performance problems. For example: Computer A has an AutoCAD drawing opened directly from the DFS share. Performance is normal, not causing any issues. Computer B begins a file transfer, putting a 11GB file onto a different DFS namespace, on the same server Computer A immediately notices lag while using AutoCAD. The cursor momentarily freezes within AutoCAD every 10 seconds or so, and any browsing of the DFS share is extremely slow. Computer B completes file transfer, and performance resumes to normal for Computer A. This is only affecting Windows 7 clients, using a variety of hardware (desktop + laptop). All of our Windows XP clients see no performance impact during the file transfer. Things I have tried with no change: Had Computer A work from an entirely different RAID array from the file transfer destination Updated NIC drivers on clients and server Enabled TCP offload and receive side scaling on the server NIC (previously disabled when the issue began) Antivirus disabled during file transfer I am currently having a user test applications other than AutoCAD when the file transfer occurs, and will update the question with that result. Does anyone have any recommendations for resolution or additional troubleshooting steps?

  Read the article

• MacBook Pro and Backtrack 5R1 Configuration

  - by user119346

  I have a Macbook pro Quad core (2.2/8gb ram/750gb hdd). I have went through tons of forums on the Internet, but none of them seemed to be updated for the current Backtrack 5R1, or the question of getting it to correctly work on the MBP. Can anyone help? I don’t have a USB Dongle, and I want to be able to use the internal airport extreme wireless of the MBP to use BT 5R1. I have downloaded Backtrack 5R1 onto VMWare Fusion, and got it up and running, but to no avail. It keeps recognizing my card as a Ethernet connection. Kismac wont recognize the card either. So what I am asking for is this: The proper “download method.” for Backtrack 5R1 to my MacBook Pro. (YES I AM WILLING TO RE-DOWNLOAD BT 5R1). The Complete process from start to finish, UP TO DATE, from someone who has done this using an MBP Running Lion OSX. The proper tweaks, settings, or commands to get my airport extreme wireless card to work (it is BROADCOM 4331 I think). The wireless connection I need to use the tools on both Backtrack 5R1 and Kismac. I mainly need to test WEP cracking on my network for security. The difference between running BT 5R1 on VMWARE Fusion and running from downloading it directly to the MBP, if there is, How to download it directly to the MBP?

  Read the article

• Dell Driver Support for Latitude E6320 Windows 7 Enterprise

  - by IamPolaris

  I recently did a reinstall of Windows 7 Enterprise on a Dell Latitude E6320, which is a 64 bit system. After the install process, and doing typical Windows Update stuff, I looked at my Device Manager and found that I had devices which were missing drivers. My missing drivers: After going to the Dell Support site and looking at the files, and doing some sleuthing I found the following support document: http://downloads.dell.com/utility/Latitude%20E-Family%20%20Mobile%20Precision%20Re-Image%20How-To%20Guide%20-%20A03%20Rev%203%200.pdf This document hints in appendix C that the Broadcom USH is the Control Point Security and the Unknown device is Micro freefall sensor. The network controller is my wireless, as I cannot connect wirelessly, and the final missing driver I am not sure. Attempting to install the control point security exe on the support page will not work. After downloading, I am given the message that I am attempting to install a 32 bit driver on a 64 bit machine EVEN THOUGH I selected the win7 64 bit option from the support page. Beyond that, some of the drivers (Which are confusing to read and hard to understand what they do) and the system utilities which are supposedly supposed to make this process simpler will either a) not run because they are 32 bit exe's or b) the support page cannot find the file attempted to download. Is there anything I can do to get (at the very least) my wireless running, but idealistically all of my drivers. A solution which assumes Dell is completely incompetent would be ideal. :P Some forums have said that I should download the chipset driver, others say to get the system utility file (DSS_UTIL_WIN_R282536.EXE). I have had no luck as of yet...

  Read the article

• Vlaning on WNR3500L

  - by ageis23

  When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off. I've also discovered that when wpa2 is switched on I don't receive a association reply from ap. thats my hostapd.conf interface=eth1 driver=broadcom bridge=br-lan ssid=O2BB3 wpa=2 wpa_passphrase=prettywoman wpa_key_mgmt=WPA-PSK rsn_pairwise=CCMP Btw that password is only temporary while am testing.

  Read the article

• How do I keep a bridge enabled on a bonded interface?

  - by jlawer

  I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

  Read the article

• Alfa AWUSO36H 1W dysfunctional driver

  - by BrainStorm

  I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

  Read the article

• Cannot ssh into server

  - by revolver

  I am trying to SSH into a linux machine running ubuntu, but the interactive shell stuck somewhere and I can't key in anything. I am on Mac OS X Lion. This only happens when I am trying to access via an external IP. Local LAN SSH is working perfectly. macbook:~ user$ ssh -v -v user@serverip // i skipped the rest of the log, but I can paste it here again if needed. Authenticated to serverip debug1: channel 0: new [client-session] debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug1: Sending env LC_CTYPE = UTF-8 debug2: channel 0: request env confirm 0 debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 My terminal shell just hang after this, and I can't key in anything. I checked var/log/auth on the server and saw that the a session is being created and I had already logged in, but I don't see any responses on my client machine. I googled around and a lot of the solution had to do with the Broadcom wireless driver, but I am not even using one, so I am pretty clueless here. To give you more information, the linux machine is also running a web server, and I have no problem accessing the web server. Thanks. Any help is appreciated.

  Read the article

• How to use non-free drivers during debian install

  - by blokeley

  I'm trying to install debian stable using unetbootin. The install process fails with "network autoconfiguration failed", probably due to the ethernet driver not working. My Lenovo U350 has a Broadcom BCM57780 which does not seem to be supported out-of-the-box: there are various bug reports here, here and here, but I don't know if the fix has made it into debian (6) stable. One discussion says that you have to use an ethernet driver from the firmware-linux-nonfree package. I'm not sure that this is correct because the BCM57780 is not in the list of drivers in firmware-linux-nonfree. The specific question tree is: Is BCM57780 supported in debian stable? If so, what could be wrong? Should I install debian unstable instead? If not, do I need to use firmware-linux-nonfree during installation and, if so, how do I do this? Please note: I've used ubuntu and debian loads in the past but please post line-by-line guidance rather than some cryptic abbreviation of any instructions. Thanks in advance for any help. Updates: Debian stable with non-free drivers did not work. Debian unstable (free drivers only) did not work. Tried loading firmware-iwlwifi_0.28_all.deb from another USB stick to get wireless working rather than BCM57780. The .deb file was found but the network configuration still failed! That's it, I'm giving up. Unfortunately I'll use ubuntu even though the Unity user interface will be very unstable for the next couple of years :(

  Read the article

• Trying to diagnose network problem: ping 127.0.0.1 (or any address) results in error code 1

  - by Mnebuerquo

  NIC seems to be working, as windows detects the hardware and has a driver and reports success. DHCP seems to have gotten an ip address, 192.168.1.101. I released and renewed it and it seemed to work normally. I tried ping 127.0.0.1 as first step of testing network configuration. Pinging 127.0.0.1 with 32 bytes of data: PING: transmit failed, error code 1. I read somewhere that net helpmsg [error code] would give a human readable name for the error code. net helpmsg 1 says "Incorrect function" I've tried disabling the firewall and antivirus in McAfee SecurityCenter and I still get the same error. Could the firewall/antivirus be breaking it even if disabled? Broadcom Advanced Control Suite 2 is installed, and its network test passes all tests, including ping 192.168.1.1 which is the default gateway. If I try ping 192.168.1.1 from the command prompt I get the error code 1 again. So does anyone have any theories that would explain this problem? Other tests I should try? Thanks!

  Read the article

• Windows 7 computer apparently connected to working wireless network but can't access router page or internet

  - by Hemmer

  I can consistently connect successfully to both the router and the internet using both my phone and two different computers which strongly suggests that the issue is at the desktop end. Only my Windows 7 desktop machine has stopped getting internet connectivity. It manages to connect to the router's network using the Windows 7 wireless dialog, but can't access either the router configuration page (192.168.1.1) or the internet in general once connected. The strange thing is the wireless network icon in the notification bar shows a full strength signal, sometimes with the yellow warning triangle. The output of ipconfig /all is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11g Network Adapter Physical Address. . . . . . . . . : 00-12-17-94-98-90 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.102(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 08 June 2011 10:32:16 Lease Expires . . . . . . . . . . : 08 June 2011 12:32:16 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 194.168.4.100 194.168.8.100 NetBIOS over Tcpip. . . . . . . . : Enabled I've tried renewing DCHP settings disabling IPv6 resetting TCP stack uninstalling and reinstalling WLAN card drivers I've not installed anything new or made any changes to my knowledge, this just happened out of the blue. The only possible change is my friend connected his macbook to the network, but that has gone now and shouldn't have any lasting effects? TCP/IPv4 is set to automatically find an IP address. Antivirus is MSE (up to date) and doesn't detect anything unusual. Any ideas where to go next? Any help is greatly appreciated. For reference, the results of ipconfig /all on one of the working computers is: Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11g Network Adapter Physical Address. . . . . . . . . : 00-16-CF-67-E5-97 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 194.168.4.100 194.168.8.100 Lease Obtained. . . . . . . . . . : 08 June 2011 10:26:38 Lease Expires . . . . . . . . . . : 08 June 2011 12:26:38 UPDATE: Still not working, but I've managed to find a temporary workaround by tethering my Android phone, effectively becoming a new wifi adapter. Will be moving to a new flat so will test if it is a network specific thing - maybe the card has got damaged somehow? Also will see if the card is working with Linux soon.

  Read the article

• Software index broken

  - by Arvind Gangwar

  When I was installing MTS Mblaz crossplatformui.deb for MTS data connect, its installed partial and shows error, and So I tried to uninstall "crossplatformui" but every time it showed following error. installArchives() failed: perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory (Reading database ... (Reading database ... 5% (Reading database ... 10% (Reading database ... 15% (Reading database ... 20% (Reading database ... 25% (Reading database ... 30% (Reading database ... 35% (Reading database ... 40% (Reading database ... 45% (Reading database ... 50% (Reading database ... 55% (Reading database ... 60% (Reading database ... 65% (Reading database ... 70% (Reading database ... 75% (Reading database ... 80% (Reading database ... 85% (Reading database ... 90% (Reading database ... 95% (Reading database ... 100% (Reading database ... 205769 files and directories currently installed.) Removing crossplatformui ... ztemtvcdromd: no process found dpkg: error processing crossplatformui (--remove): subprocess installed post-removal script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: crossplatformui Setting up firmware-b43-installer (4.150.10.5-5) ... --2012-06-01 14:11:21-- http://mirror2.openwrt.org/sources/broadcom-wl-4.150.10.5.tar.bz2 Resolving mirror2.openwrt.org... 46.4.11.11 Connecting to mirror2.openwrt.org|46.4.11.11|:80... failed: Connection refused. dpkg: error processing firmware-b43-installer (--configure): subprocess installed post-installation script returned error exit status 4

  Read the article

• Integrated webcam in lenovo t410 not working with 12.04

  - by kristianp

  I have a Lenovo T410 with an inbuilt webcam and I haven't been able to get the webcam working. I tried skype, cheese, both just give me a black window. The microphone works fine with skype, by the way. Can anyone provide any clues please? The webcam is enabled in the bios, but there is no light indicating the webcam is on (not sure if there should be, though). I tried this on Kubuntu 11.10 and have upgraded to 12.04 with the same results. The Fn-F6 keyboard combination doens't seem to do anything either. EDIT: I got the webcam replaced, it looks like it was a hardware problem, because it works fine now. Thanks guys. $ ls /dev/v4l/* /dev/v4l/by-id: usb-Chicony_Electronics_Co.__Ltd._Integrated_Camera-video-index0 /dev/v4l/by-path: pci-0000:00:1a.0-usb-0:1.6:1.0-video-index0 And lsusb: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 005: ID 17ef:480f Lenovo Integrated Webcam [R5U877] Bus 002 Device 003: ID 05c6:9204 Qualcomm, Inc. Bus 002 Device 004: ID 17ef:1003 Lenovo Integrated Smart Card Reader Here is the output from guvcview, minus lots of lines describing the available capture formats. It says "unable to start with minimum setup. Please reconnect your camera.". guvcview 1.5.3 ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, .... { discrete: width = 1600, height = 1200 } Time interval between frame: 1/15, vid:17ef pid:480f driver:uvcvideo checking format: 1196444237 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } .... vid:17ef pid:480f driver:uvcvideo checking format: 1448695129 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! ERROR: Minimum Setup Failed. Exiting... VIDIOC_REQBUFS - Failed to delete buffers: Invalid argument (errno 22) cleaned allocations - 100% Closing portaudio ...OK Terminated.

  Read the article

• Why does Ubuntu only detect one USB LAN adapters at a time?

  - by EGO

  I try to connect real switch with my computer for an exam preparation, for this purpose I need more than one LAN cards, and there is only one built in LAN card in my computer. So, to get more LAN cards, I bought 4 USB Ethernet adapters (as I have 4 usb ports in may laptop 2 usb 2.0 ports, 2 usb 3.0 ports). When I plug these adapters in my computer Ubuntu only detects one LAN card from 2.0 usb ports, and one LAN card from 3.0 ports. And sometimes detects only one USB LAN from all the usb ports. Actually the real problem is Ubuntu shows these USB LAN adapters in the "lsusb", but does not list them in "ifconfig". Kontron (Industrial Computer Source / ICS Advent) is my LAN USB ethernet. abc@ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 001 Device 003: ID 138a:0018 Validity Sensors, Inc. Bus 001 Device 004: ID 064e:e258 Suyin Corp. Bus 003 Device 011: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 013: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 003 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 005: ID 0a5c:21b4 Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR -- etho is my built in LAN card, while eth1 is the only USB LAN card that ubuntu has detected. abc@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 2c:27:d7:a5:d2:39 inet6 addr: fe80::2e27:d7ff:fea5:d239/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:21056 errors:0 dropped:1 overruns:0 frame:0 TX packets:5669 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1407289 (1.4 MB) TX bytes:372566 (372.5 KB) Interrupt:49 Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:e0:4c:53:44:58 inet6 addr: fe80::2e0:4cff:fe53:4458/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9230 errors:0 dropped:0 overruns:0 frame:0 TX packets:9230 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:557648 (557.6 KB) TX bytes:557648 (557.6 KB) wlan0 Link encap:Ethernet HWaddr cc:52:af:5e:78:05 inet addr:192.168.1.65 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::ce52:afff:fe5e:7805/64 Scope:LinkU UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17389 errors:0 dropped:0 overruns:0 frame:0 TX packets:12231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22452248 (22.4 MB) TX bytes:1502750 (1.5 MB) If I unplug the USB LAN card which Ubuntu has detected, then Ubuntu will detect a USB LAN card from the remaining plugged adapters, and process go on untill I plug all the USB LAN adapters. Looking for some urgent help. Thanks

  Read the article

• Need help partitioning when reinstalling Ubuntu 14.04

  - by Chris M.

  I upgraded to 14.04 about a month ago on my HP Mini netbook (about 16 GB hard disk). A few days ago the system crashed (I don't know why but I was using internet at the time). When I restarted the computer, Ubuntu would not load. Instead, I got a message from the BIOS saying Reboot and Select proper Boot device or Insert Boot Media in selected Boot device and press a key I took this to mean that I needed to reinstall 14.04. When I try to reinstall Ubuntu from the USB stick, I choose "Erase disk and install Ubuntu" but then I get a message: Some of the partitions you created are too small. Please make the following partitions at least this large: / 3.3 GB If you do not go back to the partitioner and increase the size of these partitions, the installation may fail. At first I hit Continue to see if it would install anyway, and it gave the message: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition # 1 (sda) at / failed. You may resume partitioning from the partitioning menu. The second time I hit Go Back, and it took me to the following partitioning table: Device Type Mount Point Format Size Used System /dev/sda /dev/sda1 ext4 (checked) 3228 MB Unknown /dev/sda5 swap (not checked) 1063 MB Unknown + - Change New Partition Table... Revert Device for boot loader installation: /dev/sda ATA JM Loader 001 (4.3 GB) At this point I'm not sure what to do. I've never partitioned my hard drive before and I don't want to screw things up. (I'm not particularly tech savvy.) Can you instruct me what I should do. (P.S. I'm afraid the table might not appear as I typed it in.) Results from fdisk: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders, total 8388608 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 7860 MB, 7860125696 bytes 155 heads, 31 sectors/track, 3194 cylinders, total 15351808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009a565 Device Boot Start End Blocks Id System /dev/sdb1 * 2768 15351807 7674520 b W95 FAT32 ubuntu@ubuntu:~$ Here is what it displays when I open the Disks utility (I tried the screenshot terminal command you suggested but it didn't seem to do anything): 4.3 GB Hard Disk /dev/sda Model: JM Loader 001 (01000001) Size: 4.3 GB (4,294,967,296 bytes) Serial Number: 01234123412341234 Assessment: SMART is not supported Volumes Size: 4.3 GB (4,294,967,296 bytes) Device: /dev/sda Contents: Unknown (There is a button in the utility that when you click it gives the following options: Format... Create Disk Image... Restore Disk Image... Benchmark but SMART Data & Self-Tests... is dimmed out) When I hit F9 Change Boot Device Order, it shows the hard drive as: SATA:PM-JM Loader 001 When I hit F10 to get me into the BIOS Setup Utility, under Diagnostic it shows: Primary Hard Disk Self Test Not Support NetworkManager Tool State: disconnected Device: eth0 Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 00:26:55:B0:7F:0C Capabilities: Carrier Detect: yes Wired Properties Carrier: off When I run command lshw -C network, I get: WARNING: you should run this program as super-user. *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:16 memory:feafc000-feafffff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: c0 serial: 00:26:55:b0:7f:0c capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:febc0000-febfffff ioport:ec80(size=128) WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• SCVMM 2012 R2 - Installing Virtual Switch Fails with Error 2916

  - by Brian M.

  So I've been attempting to teach myself SCVMM 2012 and Hyper-V Server 2012 R2, and I seem to have hit a snag. I've connected my Hyper-V Host to SCVMM 2012 successfully, and created a logical network, logical switch, and uplink port profile (which I essentially blew through with the default settings). However when I attempt to create a virtual switch on my Hyper-V host, I run into an issue. The job will use my logical network settings I created to configure the virtual switch, but when it tries to apply it to the host, it stalls and eventually fails with the following error: Error (2916) VMM is unable to complete the request. The connection to the agent vmhost1.test.loc was lost. WinRM: URL: [h**p://vmhost1.test.loc:5985], Verb: [GET], Resource: [h**p://schemas.microsoft.com/wbem/wsman/1/wmi/root/virtualization/v2/Msvm_ConcreteJob?InstanceID=2F401A71-14A2-4636-9B3E-10C0EE942D33] Unknown error (0x80338126) Recommended Action Ensure that the Windows Remote Management (WinRM) service and the VMM agent are installed and running and that a firewall is not blocking HTTP/HTTPS traffic. Ensure that VMM server is able to communicate with econ-hyperv2.econ.loc over WinRM by successfully running the following command: winrm id –r:vmhost1.test.loc This problem can also be caused by a Windows Management Instrumentation (WMI) service crash. If the server is running Windows Server 2008 R2, ensure that KB 982293 (h**p://support.microsoft.com/kb/982293) is installed on it. If the error persists, restart vmhost1.test.loc and then try the operation again. Refer to h**p://support.microsoft.com/kb/2742275 for more details. I restarted the server, and upon booting am greeted with a message stating "No active network adapters found." I load up powershell and run "Get-NetAdapter -IncludeHidden" to see what's going on, and get the following: Name InterfaceDescription ifIndex Status ---- -------------------- ------- ----- Local Area Connection* 5 WAN Miniport (PPPOE) 6 Di... Ethernet Microsoft Hyper-V Network Switch Def... 10 Local Area Connection* 1 WAN Miniport (L2TP) 2 Di... Local Area Connection* 8 WAN Miniport (Network Monitor) 9 Up Local Area Connection* 4 WAN Miniport (PPTP) 5 Di... Ethernet 2 Broadcom NetXtreme Gigabit Ethernet 13 Up Local Area Connection* 7 WAN Miniport (IPv6) 8 Up Local Area Connection* 9 Microsoft Kernel Debug Network Adapter 11 No... Local Area Connection* 3 WAN Miniport (IKEv2) 4 Di... Local Area Connection* 2 WAN Miniport (SSTP) 3 Di... vSwitch (TEST Test Swi... Hyper-V Virtual Switch Extension Ada... 17 Up Local Area Connection* 6 WAN Miniport (IP) 7 Up Now the machine is no longer visible on the network, and I don't have the slightest idea what went wrong, and more importantly how to undo the damage I caused in order to get back to where I was (save for re-installing Hyper-V Server, but I really would rather know what's going on and how to fix it)! Does anybody have any ideas? Much appreciated!

  Read the article

• Windows Vista: Networking can only connect "local only"

  - by Damien

  I am attempting to debug a problem on a Windows Vista laptop - not mine! Until just recently (last week or so), it was operating normally for about 4 years :) The problem is that I am having issues connecting to the local network (a basic wireless home router; more later) and the internet (via ADSL). This is both for wired [Broadcom chipset] and wireless [Intel chipset]. I will elaborate further later. To detail the network. I have three other clients (HTC phone, Ubuntu 12.04 desktop [wired] and Ubuntu 10.04 laptop [wireless]), all of whom are able to connect to the network and internet normally. A windows 7 virtual machine running on said desktop connects normally. I have tried two different wireless routers - Netgear DG834G and Netgear DGN3500. The same error mode is common to both. Updating the firmware to the latest on both routers does not help. Overall, it seems safe to say it's localised to the laptop in question. I do not have another Vista client to test with. The specific symptoms are as follows: When "connected", it says "Local Only", and says it cannot connect to the internet. This is true for both wired and wireless. It can get an IP address (192.168.0.5), and the router (192.168.0.1) reports that it can see the device. When I try to ping, I get the following results: ping 192.168.0.1 - (router) all packets lost ping 192.168.0.5 - (laptop's address) OK ping 192.168.0.4 - (desktop) all packets lost Pinging from the desktop to the problematic laptop results in "From 192.168.0.4 icmp_seq=1 Destination Host Unreachable" The most promising "fix" from trawling forums is KB928233 which does not work for me. The problem is persistent across reports (both full shutdown and hibernate) so it appears not to be sleep related. I am not a regular vista user, though I can fumble my way about a bit. Is there any other suggestions as to what I should do? Is there any further information I can provide?

  Read the article

• Cliq Wireless questions

  - by Nathan Adams

  Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

  Read the article

< Previous Page | 11 12 13 14 15 16 17  | Next Page >