Search Results

Search found 5195 results on 208 pages for 'shift reduce conflict'.

Page 152/208 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

• 24TB RAID 6 configuration

  - by Phil

  I am in charge of a new website in a niche industry that stores lots of data (10+ TB per client, growing to 2 or 3 clients soon). We are considering ordering about $5000 worth of 3TB drives (10 in a RAID 6 configuration and 10 for backup), which will give us approximately 24 TB of production storage. The data will be written once and remain unmodified for the lifetime of the website, so we only need to do a backup one time. I understand basic RAID theory, however I am not experienced with it. My question is, does this sound like a good configuration? What potential problems could this setup cause? Also, what is the best way to do a one-time backup? Have two RAID 6 arrays, one for offsite backup and one for production? Or should I backup the RAID 6 production array to a JBOD? EDIT: The data server is running Windows 2008 Server x64. EDIT 2: To reduce rebuild time, what would you think about using two RAID 5's instead of one RAID 6?

  Read the article

• Computer turns off unexpectedly

  - by Shahar

  My computer turns itself off unexpectedly after some time of use. It appears that this might be temperature related, but not for sure. I installed 2 tools that monitor temperature: SpeedFan and CPU Thermometer. The only definite finding is that there is a sensor (labelled temp1 in SpeedFan and CPU in CPU thermometer), which shows a temperature of 108C a second before the computer powers down. Until that moment, this sensor shows a constant temperature of 40C. I can usually reproduce the shutdown by viewing a few movies together, which cause another sensor (labelled CPU in SpeedFan) to go up to 60sC, but I do experience the problem even at times when this sensor remains low and cool. It does seem that the problem is more frequent if the computer is turned back on immediately after shutdown, but not always. I have had other hardware problems recently, which might be related: My hard disk heated up. I installed a fan on it, which worked to reduce the heat. The hard disk sensor shows around 40C. I had occasional blue screens and hard disk failures. Replacing the power supply seems to solve both these issues, but then this powerdown problem began appearing. I would appreciate any suggestions as to how to determine where the fault is, or what needs to be replaced.

  Read the article

• How to utilize Varnish for A/B Testing and Feature Rollout?

  - by Ken

  Hi all, wasn't really sure if this should go here on or stackoverlow - admins, please move if i'm mistaken (and sorry). Today we have our web layer exposed to the world. We would like to add Varnish in front of our web layer to accelerate the site and reduce calls to the backend. However, we have some concerns and i was wondering how most people approach them: A/B Testing - How do you test two "versions" of each page and compare? I mean, how does varnish know which page to serve up? If and how do you save seperate versions on each page? Feature rollout - how would you set up a simple feature rollout mechanism? Let's say i want to open a new feature/page to just 10% of the traffic.. and then later increase that to 20%? How do you handle code deployments? Do you purge your entire varnish cache every deployment? (We have deployments on a daily basis). Or do you just let it slowly expire (using TTL)? Any ideas and examples regarding these issues is greatly appreciated! Thanks in advance. Ken.

  Read the article

• Resource Monitor (resmon) in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

  Read the article

• How to compress .pdfs in word 2007?

  - by chobo2

  Hi I am trying to send my cover letter and resume away but apparently it is too big to send through craigs list(my computer says the total size is 500kb) as it has a 600kb limit(so small should be at least a meg). Hi there. You recently tried to email Some job Email, an anonymous craigslist address. However, your message was too big to be sent through our system. Craigslist has a 600KB limit on the messages we'll send. Please reduce the size of your mail and try again. Thanks for using craigslist. So when I convert my word 2007(.docx) files to pdf they become huge. Like they got from 32kb to 320kb. So is there a way I can either get around craigslist limits or compress my pdfs a bit to make it happy. I don't want to send zips and stuff since the person who gets it might not even know what to do. I rather not send .docx since not sure if will have office 2007 or the compatibility view installed and I rather just send it as pdf(as some place require it anyways to be in pdfs). Thanks

  Read the article

• Perl EPIC Not recognising installed CPAN modules

  - by Recc

  Eclipse on a mac, was working fine adding new modules until I Installed Text::CSV_XS which Eclips doesn't recognise as added to @INC For instance use strict; use SOAP::Transport::HTTP; SOAP::Transport::HTTP::CGI->dispatch_to('C2FService')->handle; BEGIN { package C2FService; use vars qw(@ISA); @ISA = qw(Exporter SOAP::Server::Parameters); use SOAP::Lite; sub c2f { my $self = shift; my $envelope = pop; my $temp = $envelope->dataof("//c2f/temperature"); return SOAP::Data->name( 'convertedTemp' => ( ( ( 9 / 5 ) * ( $temp->value ) ) + 32 ) ); } } use SOAP::Transport::HTTP; is marked as error if I comment it out use SOAP::Lite; is in turn marked as an error, not found etc the usual if a module is not installed. Both are installed with CPAN and $ perl -c soap-test.pl post-code-check.pl syntax OK Perl is fine CPAN tests are all pass, the code works, only EPIC lags behind. $ pwd && ls /opt/local/lib/perl5/site_perl/5.12.4/SOAP Client.pod Lite Server.pod Constants.pm Lite.pm Test.pm Data.pod Packager.pm Trace.pod Deserializer.pod SOM.pod Transport Fault.pod Schema.pod Transport.pod Header.pod Serializer.pod Utils.pod And if I have use errors in the start of my files the rest of the source is not error checked..

  Read the article

• Software to clean up photos of whiteboards and documents?

  - by Norman Ramsey

  I take a lot of photos of whiteboards, blackboards, and so on for teaching purposes (examples online through May 2010). I'm interested in cleaning them up for archival purposes, preferably using Linux. Commercial products ClearBoard and PhotoNote are priced a little aggressively for my purposes, plus my students would like to have this capability too. Does anyone know of any good, open source software for Converting photographs to images with just a few colors? Eliminating perspective distortion? Removing unwanted junk from around the edges of an image? or anything like that? I'm imagining that I start out with a picture of my whiteboard using red and black markers, and I end up with a three-color image using just white, red, and black. Or I photograph a laser-printed document and end up with a clean black-and-white image. I have tried standard tools that reduce the number of colors in an image, and they do a terrible job—probably because they are trying to reproduce the uneven illumination of the original image. Command-line Linux tools would be ideal.

  Read the article

• Server Directory Not Accessible

  - by GusDeCooL

  I got strange things happen on live server, but normal in local server. My local server is using mac, and my live server is linux. Consider i try to access some files http://redddor.babonmultimedia.com/assets/images/map-1.jpg This work correctly. http://redddor.babonmultimedia.com/assets/modules/evogallery/check.php Return 404, I'm pretty sure my file is in there and there is no typo mistake. How come it give me 404? There is only one .htaccess on the root server and it's configuration is like this. # For full documentation and other suggested options, please see # http://svn.modxcms.com/docs/display/MODx096/Friendly+URL+Solutions # including for unexpected logouts in multi-server/cloud environments # and especially for the first three commented out rules #php_flag register_globals Off #AddDefaultCharset utf-8 #php_value date.timezone Europe/Moscow Options +FollowSymlinks RewriteEngine On RewriteBase / <IfModule mod_security.c> SecFilterEngine Off </IfModule> # Fix Apache internal dummy connections from breaking [(site_url)] cache RewriteCond %{HTTP_USER_AGENT} ^.*internal\ dummy\ connection.*$ [NC] RewriteRule .* - [F,L] # Rewrite domain.com -> www.domain.com -- used with SEO Strict URLs plugin #RewriteCond %{HTTP_HOST} . #RewriteCond %{HTTP_HOST} !^www\.example\.com [NC] #RewriteRule (.*) http://www.example.com/$1 [R=301,L] # Exclude /assets and /manager directories and images from rewrite rules RewriteRule ^(manager|assets)/*$ - [L] RewriteRule \.(jpg|jpeg|png|gif|ico)$ - [L] # For Friendly URLs RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php?q=$1 [L,QSA] # Reduce server overhead by enabling output compression if supported. #php_flag zlib.output_compression On #php_value zlib.output_compression_level 5

  Read the article

• Ctrl + 1 and Ctrl + 2 key combinations don't work

  - by musicfreak

  I noticed back in August (when I got StarCraft 2) that the key combinations Ctrl + 1 and Ctrl + 2 didn't work. I thought this was weird because Ctrl + 3 and all the other combinations worked fine (including Shift + 1, etc), so I didn't think much of it; I just shrugged it off as a SC2 bug. Now, 4 months later, I decided to play a completely unrelated game--Dawn of War 2--and noticed the same thing: those two specific key combinations don't work. To make sure I wasn't going insane, I tried it in Chrome and a couple other applications, and alas, it didn't work. I remember playing strategy games over the summer before StarCraft 2 and it worked fine. Any idea as to what went wrong? My keyboard, a Microsoft Wireless Keyboard 1000 (I know, insert Microsoft joke here), is a little over a year old, so I'm going to assume it's not dying until proven otherwise. Things I've tried ActiveHotkeys says the key combination is not a global hotkey. Tried another keyboard--still doesn't work. The key combinations do work in a virtual machine (tried with both Windows and Ubuntu as guests).

  Read the article

• Nginx proxy with Redmine SVN authentication.

  - by Omegaice

  I am attempting to setup a system where I have an nginx server running as a reverse proxy for multiple websites that I want to run. To separate the websites I have created a Linux container which contains each site to allow me to reduce conflicts in database usage etc. I am currently trying to get my main site working and have nginx with passenger setup and connecting to redmine and I have an Apache install specifically setup for serving the SVN over HTTP and am attempting to use the redmine authentication with that. I have set everything up as described in the redmine howtos, but when I check a project out from the SVN it always works even if the project is private and whenever I try and commit to the repositories it fails saying "Could not open the requested SVN filesystem", the Apache error log related to that event is "(20014)Internal error: Can't open file '/srv/rcs/svn/error/format': No such file or directory". If I take out the redmine authentication I can checkout and check-in repositories fine but there is no authentication. Does anyone have any ideas? Edit I tried to solve this problem another way by attempting to have the authentication work by LDAP, I managed to get it so that my user could log into the redmine website but as soon as I tried to check anything out it said that access was forbidden to the repository.

  Read the article

• Reducing IO caused by nginx

  - by glumbo

  I have a lot of free RAM but my IO is always 100 %util or very close. What ways can I reduce IO by using more RAM? My iotop shows nginx worker processes with the highest io rate. This is a file server serving files ranging from 1mb to 2gb. Here is my nginx.conf #user nobody; worker_processes 32; worker_rlimit_nofile 10240; worker_rlimit_sigpending 32768; error_log logs/error.log crit; #pid logs/nginx.pid; events { worker_connections 51200; } http { include mime.types; default_type application/octet-stream; access_log off; limit_conn_log_level info; log_format xfs '$arg_id|$arg_usr|$remote_addr|$body_bytes_sent|$status'; sendfile off; tcp_nopush off; tcp_nodelay on; directio 4m; output_buffers 3 512k; reset_timedout_connection on; open_file_cache max=5000 inactive=20s; open_file_cache_valid 30s; open_file_cache_min_uses 2; open_file_cache_errors on; client_body_buffer_size 32k; server_tokens off; autoindex off; keepalive_timeout 0; #keepalive_timeout 65;

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• SSH client and Command Prompt replacements Windows look-and-feel

  - by Oddthinking

  The Problem I've worked exclusively in Windows. I can handle that. I've worked exclusively in DOS (a long time ago!). I can handle that. I've worked exclusively in Unix. I can handle that. Right now, I am developing a command-line (python) application on a Windows machine, testing it in a DOS box (i.e. Windows' Command prompt), and then deploying it to Linux, and running it with PuTTY. I cannot handle that. My productivity drops dramatically when CTRL-C cuts in one window (Windows) and kills the process in another (DOS, Linux). My productivity drops dramatically when Enter copies the selection in one window (DOS), and deletes the selection in another (Windows), and runs the current half-edited command in the third (PuTTY). My productivity drops dramatically when I cannot hit Undo, Home or End. The Solution I am Seeking An SSH/Bash command-line client that runs on Windows and, to the extent possible, uses all the standard Windows shortcuts (Cut, Copy, Paste, Undo, Home, End, Insert, Shift-Arrows, etc.) work on a bash command line. Bonus points if it puts the cursor between letters, rather than on them. Plus, an equivalent DOS command-line drop-in that runs on Windows, and provides the same interface. I appreciate there may need to be special buttons to actually transfer CTRL codes (like CTRL-C) through in the cases I need them. I suspect the SSH client will need to be specific to a shell (so it knows when it is at the command prompt, and when it is inside a running app.) I know there are many SSH clients, but I am looking for advice for a particular need. PuTTY feels like an escape route for Unix programmers stuck on Windows. I am the opposite. Can anyone recommend one (or maybe a combination of an SSH client and an Command-Line replacement)?

  Read the article

• MySQL-Cluster or Multi-Master for production? Performance issues?

  - by Phillip Oldham

  We are expanding our network of webservers on EC2 to a number of different regions and currently use master/slave replication. We've found that over the past couple of months our slave has stopped replicating a number of times which required us to clear the db and initialise the replication again. As we're now looking to have servers in 3 different regions we're a little concerned about these MySQL replication errors. We believe they're due to auto_increment values, so we're considering a number of approaches to quell these errors and stabilise replication: Multi-Master replication; 3 masters (one in each region), with the relevant auto_increment offsets, regularly backing up to S3. Or, MySQL-Cluster; 3 nodes (one in each region) with a separate management node which will also aggregate logs and statistics. After investigating it seems they both have down-sides (replication errors for the former, performance issues for the latter). We believe the cluster approach would allow us to manage and add new nodes more easily than the Multi-Master route, and would reduce/eliminate the replication issues we're currently seeing. But performance is a priority. Are the performance issues of MySQL-Cluster as bad as people say?

  Read the article

• Mysql server won't start - no logs

  - by Owen

  After a restart, mysql won't start. sudo service mysql start gives start: Job failed to start and the logs are empty, so I have no idea where to start. I'm pretty sure permissions problems are taken care of. Edit: All disks have at least 1G of space and sh -x /etc/init.d/mysql start gives me: + set -e + basename /etc/init.d/mysql + INITSCRIPT=mysql + JOB=mysql + [ mysql = upstart-job ] + [ -z start ] + COMMAND=start + shift + [ -z ] + ECHO=echo + echo Rather than invoking init scripts through /etc/init.d, use the service(8) Rather than invoking init scripts through /etc/init.d, use the service(8) + echo utility, e.g. service mysql start utility, e.g. service mysql start + echo + echo Since the script you are attempting to invoke has been converted to an Since the script you are attempting to invoke has been converted to an + echo Upstart job, you may also use the start(8) utility, e.g. start mysql Upstart job, you may also use the start(8) utility, e.g. start mysql + grep -q start/ + status mysql + [ -z ] + [ start = stop ] + [ -n ] + start mysql start: Rejected send message, 1 matched rules; type="method_call", sender=":1.105" (uid=1000 pid=3208 comm="start mysql ") interface="com.ubuntu.Upstart0_6.Job" member="Start" error name="(unset)" requested_reply="0" destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")

  Read the article

• Is basing storage requirements based on IOPS sufficient?

  - by Boden

  The current system in question is running SBS 2003, and is going to be migrated on new hardware to SBS 2008. Currently I'm seeing on average 200-300 disk transfers per second total across all the arrays in the system. The array seeing the bulk of activity is a 6 disk 7200RPM RAID 6 and it struggles to keep up during high traffic times (idle time often only 10-20%; response times peaking 20-50+ ms). Based on some rough calculations this makes sense (avg ~245 IOPS on this array at 70/30 read to write ratio). I'm considering using a much simpler disk configuration using a single RAID 10 array of 10K disks. Using the same parameters for my calculations above, I'm getting 583 average random IOPS / sec. Granted SBS 2008 is not the same beast as 2003, but I'd like to make the assumption that it'll be similar in terms of disk performance, if not better (Exchange 2007 is easier on the disk and there's no ISA server). Am I correct in believing that the proposed system will be sufficient in terms of performance, or am I missing something? I've read so much about recommended disk configurations for various products like Exchange, and they often mention things like dedicating spindles to logs, etc. I understand the reasoning behind this, but if I've got more than enough random I/O overhead, does it really matter? I've always at the very least had separate spindles for the OS, but I could really reduce cost and complexity if I just had a single, good performing array. So as not to make you guys do my job for me, the generic version of this question is: if I have a projected IOPS figure for a new system, is it sufficient to use this value alone to spec the storage, ignoring "best practice" configurations? (given similar technology, not going from DAS to SAN or anything)

  Read the article

• First Day of Data Integration Track at Oracle OpenWorld 2012

  - by Irem Radzik

  OpenWorld started full speed for us today with a great set of sessions in the Data Integration track. After the exciting keynote session on Oracle Database 12c in the morning; Brad Adelberg, VP of Development for Data Integration products, presented Oracle’s data integration product strategy. His session highlighted the new requirements for data integration to achieve pervasive and continuous access to trusted data. The new requirements and product focus areas presented in this session are: Provide access to any data at any source On premise or on cloud Enable zero downtime operations and maximum performance Leverage real-time data for accurate business insights And ensure high quality data is used across the enterprise During the session Brad walked over how Oracle’s data integration products, Oracle Data Integrator, Oracle GoldenGate, Oracle Enterprise Data Quality, and Oracle Data Service Integrator, deliver on these requirements and how recent product releases build on this strategy. Soon after Brad’s session we heard from a panel of Oracle GoldenGate customers, St. Jude Medical, Equifax, and Bank of America, how they achieved zero downtime operations using Oracle GoldenGate. The panel presented different use cases of GoldenGate, from Active-Active replication to offloading reporting. Especially St. Jude Medical’s implementation, which involves the alert management system for patients that use their pacemakers, reminded me in some cases downtime of mission-critical systems can be a matter of life or death. It is very comforting to hear that GoldenGate delivers highly-reliable continuous availability for life-saving medical systems. In the afternoon, Nick Wagner from the Product Management team and I followed the customer panel with the review of Oracle GoldenGate 11gR2’s New Features.  Many questions we received from audience were about GoldenGate’s new Integrated Capture for Oracle Database and the enhanced Conflict Management features, as well as how GoldenGate compares to Oracle Streams. In addition to giving details on GoldenGate’s unique capability to capture changed data with a direct integration to the Oracle DBMS engine, we reminded the audience that enhancements to Oracle GoldenGate will continue, while Streams will be primarily maintained. Last but not least, Tim Garrod and Ryan Fonnett from Raymond James presented a unified real-time data integration solution using Oracle Data Integrator and GoldenGate for their operational data store (ODS). The ODS supports application services across the enterprise and providing timely data is a critical requirement. In this solution, Oracle GoldenGate does the log-based change data capture for Oracle Data Integrator’s near real-time data integration between heterogeneous systems. As Raymond James’ ODS supports mission-critical services for their advisors, the project team had to set up this integration environment to be highly available. During the session, Ryan and Tim explained how they use ODI to enable automated process execution and “always-on” integration processes. Their presentation included 2 demonstrations that focused on CDC patterns deployed with ODI and the automated multi-instance execution and monitoring. We are very grateful to Tim and Ryan for their very-well prepared presentation at OpenWorld this year. Day 2 (Tuesday) will be also a busy day in our track. In addition to the Fusion Middleware Innovation Awards ceremony at 11:45am at Moscone West 3001, we have the following DI sessions Real-World Operational Reporting Customer Panel 11:45am Moscone West- 3005 Oracle Data Integrator Product Update and Future Strategy 1:15pm Moscone West- 3005 High-volume OLTP with Oracle GoldenGate: Best Practices from Comcast 1:15pm Moscone West- 3005 Everything You need to Know about Monitoring Oracle GoldenGate 5pm Moscone West-3005 If you are at OpenWorld please join us in these sessions. For a full review of data integration track at OpenWorld please see our Focus-On document.

  Read the article

• Spotlight actually searching every file on "This Mac"

  - by Cawas

  I know of 2 ways to search for any file in your machine using Finder (some say it's Spotlight) and no Terminal. To prevent answers / comments about Terminal, I consider it either for scripting something or as last resource. It's not practical for lots of usages. For instance, if you want to find something to attach to a mail, or embed in iTunes or any other app, you can just drag n' drop one or many of them. Definitely not practical to do under Terminal. There are many cases of use for any, but the focus here is Graphical User Interface. Well, the 2 ways basically are: Press Cmd + Opt + Spacebar and type in your search. Press the + button, select "System files" and "are included". This is so far my preferred way, but I'm not sure it will go through every file. Open Finder, press Cmd + Shift + G and/or select just one folder. Type in your search and select the folder rather than "This Mac". This will bring files not shown in "This Mac" if you select a folder outside of the default scope. Thing is, none of those is really convenient or have the nice presentation from regular Spotlight, which you get from Cmd + Spacebar and just typing. And, as far as I've heard, the default behavior on Spotlight in Tiger was actually being able to find files anywhere. So, is there any way to make the process significantly simpler? Maybe some tweak, configuration or really good Spotlight alternative? I'd rather keep it simple and tweak Spotlight.

  Read the article

• What speed are Wi-Fi management and control frames sent at?

  - by Bryce Thomas

  There are a bunch of different 802.11 Wi-Fi standards, e.g. 802.11a, 802.11b, 802.11g, 802.11n etc. that all support different speeds. Wi-Fi frames are generally categorised as one of the following: Data frames - carry the actual application data Control frames - coordinate when its safe to send/reduce collisions Management frames - handle connection discovery/setup/tear down (e.g. AP discovery, association, disassociation) My question is about whether all these frames, and specifically management frames, are transmitted at the fastest supported speed available, or whether certain classes of frames are transmitted at some lowest common denominator speed. I have noticed that when I put an 802.11b/g only device into monitor mode and capture traffic over the air, I still see management frames (e.g. association/disassociation) being transmitted between my phone and AP which are both 802.11n, even though 802.11n has a higher transfer rate. So I am imagining one of two possibilities: My 802.11n phone/AP had to negotiate a slower speed for some reason and that's why I can see their frames on my 802.11b/g monitoring device. Management frames (and perhaps control frames also?) are sent at a lower speed, and it's only data frames that are transmitted faster with newer 802.11 standards. The reason I would like to know which one of these two possibilities (or perhaps a third possibility) is the case is that I want to capture management frames, and need to know whether using an 802.11b/g card is going to lead to me missing some frames sent at higher speeds than the monitoring card can observe. If management frames are indeed sent at a slower rate, then it's all good. If I just happen to be seeing the management frames because my phone/AP have negotiated a slower rate though, then I need to reconsider what card I use for packet capture.

  Read the article

• Lotus Domino - DAOS not reducing file size?

  - by SydxPages

  I have implemented DAOS on a Lotus Domino Server (8.5.3 FP2) as follows: Lotus Domino Server Document: Store file attachments in DAOS: Enabled Minimum size of object before Domino will store in DAOS: 64000 bytes DAOS base path: E:\DAOS Defer object deletion for: 30 days Transaction logging is running, and the specific test database has the following advanced properties set: Domino Attachment and Object Service (ticked) Use LZ1 compression for atachments Compress Database Design Compress Data I have restarted the server. When I run a compact -c, it compacts the database, but does not reduce the size. I have checked the DB in Windows Explorer (60Gb) and the size is the same pre and post. I have checked the directory (E:\DAOS) and it is 35Gb in size. When I run the command 'Tell DAOSMgr Status tmp\test.nsf', I get the following response. From looking up on the net, I believe ticket count = 0 means that the db is not really DAOS'ed? Admin Process: Searching Administration Requests database DAOSMGR: Status tmptest.nsf started DAOS database status: Database: E:\Lotus\Domino\Data\tmp\test.nsf Database state = Synchronized Last resynchronized: 03/09/2012 02:49:13 PM Ticket count: 0 DAOSMGR: Status tmp\test.nsf completed I have run fixup on the database. When I have tried to run the DAOS estimator it has always crashed. This was a problem with larger databases on earlier versions of domino, but not anymore. Can anyone tell me why the size has not reduced? Am I missing anything?

  Read the article

• Script to unstick VNC keys?

  - by MidnightLightning

  I've run into dropped key events when connecting via VNC clients, leading to a "stuck key" (usually a meta key like CTRL or ALT) and searching around the common answer on how to solve it is often "press and release each meta key individually until the problem resolves". However, I've found this to be annoying and time consuming to try and solve it this way. Plus on a bad connection, it sometimes will miss the "key up" event for the meta key again, and still keep the key stuck. So I'm looking for an automated way to do this: From a script on the client side or the server side, is there a way to trigger "key up" events for all the meta keys (CTRL, ALT, SHIFT, and WIN/CMD, both Left and Right versions)? Or just a command to release all keys the server thinks are down at the moment? Or some scripted way to at least list which keys the server end thinks are down so I know which key to keep pressing and releasing to try and release it? I've got a Mac on the server end, so a Mac/Linux solution would be needed for my situation.

  Read the article

• location of index.html CentOS 6

  - by user2118559

  Based on this http://www.servermom.com/how-to-add-new-site-into-your-apache-based-centos-server/454/ tutorial installed Apache-based CentOS Server I use putty.exe as editor vi /etc/httpd/conf/httpd.conf at very bottom modified to <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/fikitipis.com/public_html ServerName www.fikitipis.com ServerAlias fikitipis.com ErrorLog /var/www/fikitipis.com/error.log CustomLog /var/www/fikitipis.com/requests.log common </VirtualHost> So expect that index is at /var/www/fikitipis.com/public_html When in browser type ip address of server, see Apache 2 Test Page powered by CentOS and so on You may now add content to the directory /var/www/html/ Then [root@vps ~]# ls /var/www/ see cgi-bin domain.com error fikitipis.com html icons Checking content of directories ls /var/www/domain.com/public_html, ls /var/www/fikitipis.com/public_html, /var/www/html/ are empty Where is index.html? Did touch /var/www/fikitipis.com/public_html/index1.html then vi /var/www/fikitipis.com/public_html/index1.html, typed a, then wrote some text in file, then Escape and shift+zz. And in browser http://111.111.11.111/index1.html and see what I had wrote. So until now seems that all works

  Read the article

• Why doesn't the monitor output anything in Linux console mode?

  - by flypen

  I install Linux without graphics support. Previously I used a monitor with 720p support. And it can display normally. Now I change to a monitor with 1080p support. I can see BIOS and GRUB info on monitor, and kernel messages in early stages. However, the monitor says that there is no input immediately, and then I can't see anything again. It seems that it happens after something initializes. Is it related to vesafb? vesafb: mode is 1280x1024x32, linelength=5120, pages=0 vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 mtrr: type mismatch for 7f800000,800000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,400000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,200000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,100000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,80000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,40000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,20000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,10000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,8000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,4000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,2000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,1000 old: write-back new: write-combining vesafb: framebuffer at 0x7f800000, mapped to 0xffffc90011380000, using 5120k, total 5120k Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device

  Read the article

• HTML tabindex: Put some links last without complete enumeration

  - by Emanuel Berg

  I know I can use the HTML anchor attribute tabindex to set the tabindex of links, i.e., in what order they get focused when the user hits Tab (or Shift-Tab). But, I have a home page with tons of links, and to enumerate all those is a lot of work. The actual case is, I have four image links that by default gets index 1, 2, 3, and 4 (well, the behavior is equivalent, at least). But, I'd much rather have the first non-image link as number 1. Check it out here and you'll understand immediately. I tried to give the first non-image link (the link I desire to have tabindex 1) - I tried to give it tabindex 1 explicitly, hoping that it would cascade from there, but it didn't (i.e., the first image link got implicit tabindex 2). I also tried to give the image links ridiculously high tabindexes, but that didn't work: as the other links didn't have tabindexes at all, those highs were still "first". As a last resort (the solution currently employed) I gave the image links all tabindex -1. That makes for logical tabbing, but, it is suboptimal, as those image links are excluded from the tab loop - a user tabbing away will probably never realize that the images are clickable. I'd like them to be reachable with tabbing, but last, after all the ordinary links. If you wonder why I'm so determined to achieve this, it has to do with my own finger habits: I almost exclusively search for links, tab back, tab forth, etc., and very seldom using the mouse. Note: I'll accept a script to change the actual HTML for a complete enumeration, if you convince me there is no "set" way to solve this problem.

  Read the article

• Creating basic, redundant gigE or IB storage network for Xen?

  - by StaringSkyward

  With only a modest budget, I want to move my 4 xen servers over to network storage -either NFS or iSCSI which will be determined based on how well it performs when we test it (we need good throughput and it must continue to work through link and switch failure tests). We may add another couple of xen servers at some point when this is done. I don't know much about the design and operation of storage networks, so would really appreciate some hints from those with experience. The budget is around $3,800 excluding the storage appliance. I am currently thinking these are my options to remain on budget: 1) Go for used infiniband hardware and aim for 10gb performance. 2) Stick with gig ethernet and buy some new switches (cisco or procurve) to create a storage-only ethernet LAN. Upgrade to 10gigE later but try to use hardware capable of it where possible to reduce upgrade costs. I have seen used, warrantied infiniband switches at reasonable prices (presumably because big companies are converging on 10gbit ethernet?) and the promise of cheap 10gb is attractive. I know nothing about IB, so here come the questions: Can I buy 2 x switches and have multiple HBAs in my xen and storage nodes to get redundancy and increased performance without complexity or expensive management software costs? If so, can you point me to some examples? Do NFS and iSCSI work just the same regardless? Is IB a sensible choice or could/should I use ethernet or FC on the same budget - I'm keen not to get boxed into a corner for future upgrades, however. For the storage I am likely to build a storage server using nexentastor with the intention that I can later add more disks, SSDs and add another server to provide a failover option at the storage level. An HP LeftHand starter SAN is also under consideration, too. Thanks in advance.

  Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >