Search Results

Search found 1620 results on 65 pages for 'proc'.

Page 16/65 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

  • enable iptables firewall on linux

    - by user13278061
     Here is a very basic set of instruction to setup a simple iptables firewall configuration on linux (redhat) Enable firewall log as root thenenter the following command, it launch a text gui #> setup first screen: Choose firewall configuration second screen: choose "Enabled" then "Customize" third screen: select you interface in "Trusted Devices", select "Allow Incoming" for "SSH" "Telnet" "FTP" (add eventually other ports, then press "OK" (2 times, then "Quit") At that point the firewall is enabled. You can start/stop/monitor using service iptables start/stop/status Change timeout to changed the tcp established connection timeout #> echo 120 >    /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established Monitor connection in iptables tables for example if you want to track a connection establish from a host  152.68.65.207 #> cat /proc/net/ip_conntrack |grep 152.68.65.207

    Read the article

  • After I backed up my ubuntu 12.04, my system crashed

    - by user95490
    Outline: I use the way shown on http://ubuntuforums.org/showthread.php?t=35087 to backup my linux system, but somehow when I restore it, it crashes. Problem Description: When I reboot, there's an information: Gave up waiting for root device. Common problems: -- Boot args (cat /proc/cmdline) -- Check rootdisplay = (did the system wait long enough?) -- Check root = (did the system wait for the right device?) -- Missing modules (cat /proc/modules; ls dev) ALERT! /dev/disk/by-uuid/9cf6f563-86d1-47be-bc26-92dd7df35cb3 does not exist. Dropping to a shell!

    Read the article

  • "Could not claim interface on camera: -6" when trying to connect usb camera (Kinect)

    - by rzetterberg
    I have installed the freenect library from openkinect.org. With that library there is a demo application which you can run from the terminal to test out the Kinect. However when I run this command I get the following output: richard@behemoth:~$ sudo freenect-glview Kinect camera test Number of devices found: 1 Could not claim interface on camera: -6 Could not open device This particular error is thrown by the library libusb by the function libusb_claim_interface and the error -6 corresponds to the LIBUSB_ERROR_BUSY. So my guess is that it has something to do with mounting the usb, rather than specifically the freenect library or the Kinect itself. So my question is how can I find out what resource is using this interface and how can I free it so that I can access it? Edit: What I have tried so far (just to be sure): Rebooted Plugged-out, plugged-in Tried different usb ports Restarted udev Additional information that might be useful: /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=1c73f217-ac8d-451b-8390-7a680628a856 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=bb49bd29-07ec-45a0-bbab-46fb8362b06b none swap sw 0 0 sudo uname -r: Linux behemoth 3.0.0-14-generic-pae #23-Ubuntu SMP Mon Nov 21 22:07:10 UTC 2011 i686 i686 i386 GNU/Linux cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10"

    Read the article

  • When I restart my virtual enviorment it does not re-bind to the IP address

    - by RoboTamer
    The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

    Read the article

  • "postgres blocked for more than 120 seconds" - is my db still consistent?

    - by nn4l
    I am using an iscsi volume on an Open-E storage system for several virtual machines running on a XenServer host. Occasionally, when there is a very high disk I/O load on the virtual machines (and therefore also on the storage system), I got this error message on the vm consoles: [2594520.161701] INFO: task kjournald:117 blocked for more than 120 seconds. [2594520.161787] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [2594520.162194] INFO: task flush-202:0:229 blocked for more than 120 seconds. [2594520.162274] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [2594520.162801] INFO: task postgres:1567 blocked for more than 120 seconds. [2594520.162882] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. I understand this error message is caused by the kernel to inform that these processes haven't been run for 120 seconds, most likely because a disk access to the storage system has not yet been processed. But what is the effect on the processes. For example, will the postgres process eventually write its data when the storage system is idle again after a few minutes, so that all data is still consistent? Or will it abort the write, leaving some tables in an inconsistent state? I certainly expect that the former should be the case - if the disk access is slow, postgres (or any other affected process) should just wait as long as it takes. I can live with the application hanging for a few minutes. But if there is a chance for data corruption then any of these errors is really bad news. Please advise what to do here.

    Read the article

  • Package upgrade on Ubuntu raid server and grub setup issue

    - by RecNes
    I have remote Ubuntu 10.10 server running on raid system. I did package upgrade yesterday night for security reasons. During the upgrade, grub installation screen appeared and asked me which partition I wanted to install grub. Options are sda,sdb,md1 and md2. I decide to install them on both sda and sdb partitions. I wondering, was I make true decision? If machine get reboot is it can be boot up safely? You can find fdisk output and fstab mount points below: Fstab: proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/md0 none swap sw 0 0 /dev/md1 /boot ext3 defaults 0 0 /dev/md2 / ext3 defaults 0 0 Fdisk: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00029bb5 Device Boot Start End Blocks Id System /dev/sda1 1 262 2102562 fd Linux raid autodetect /dev/sda2 263 295 265072+ fd Linux raid autodetect /dev/sda3 296 91201 730202445 fd Linux raid autodetect Disk /dev/md0: 2152 MB, 2152923136 bytes 2 heads, 4 sectors/track, 525616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md1: 271 MB, 271319040 bytes 2 heads, 4 sectors/track, 66240 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table Disk /dev/md2: 747.7 GB, 747727224832 bytes 2 heads, 4 sectors/track, 182550592 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00088969 Device Boot Start End Blocks Id System /dev/sdb1 1 262 2102562 fd Linux raid autodetect /dev/sdb2 263 295 265072+ fd Linux raid autodetect /dev/sdb3 296 91201 730202445 fd Linux raid autodetect

    Read the article

  • GlusterFS is failing to mount on boot

    - by J. Pablo Fernández
    I'm running the official GlusterFS 3.5 packages on Ubuntu 12.04 and everything seems to be working fine, except mounting the GlusterFS volumes at boot time. This is what I see in the log files: [2014-06-13 08:52:28.139382] I [glusterfsd.c:1959:main] 0-/usr/sbin/glusterfs: Started running /usr/sbin/glusterfs version 3.5.0 (/usr/sbin/glusterfs --volfile-server=koraga --volfile-id=/private_uploads /var/www/shared/private/uploads) [2014-06-13 08:52:28.147186] I [socket.c:3561:socket_init] 0-glusterfs: SSL support is NOT enabled [2014-06-13 08:52:28.147237] I [socket.c:3576:socket_init] 0-glusterfs: using system polling thread [2014-06-13 08:52:28.148183] E [socket.c:2161:socket_connect_finish] 0-glusterfs: connection to 176.58.113.205:24007 failed (Connection refused) [2014-06-13 08:52:28.148236] E [glusterfsd-mgmt.c:1601:mgmt_rpc_notify] 0-glusterfsd-mgmt: failed to connect with remote-host: koraga (No data available) [2014-06-13 08:52:28.148251] I [glusterfsd-mgmt.c:1607:mgmt_rpc_notify] 0-glusterfsd-mgmt: Exhausted all volfile servers [2014-06-13 08:52:28.148477] W [glusterfsd.c:1095:cleanup_and_exit] (-->/usr/lib/x86_64-linux-gnu/libgfrpc.so.0(rpc_transport_notify+0x27) [0x7fe077f8e0f7] (-->/usr/lib/x86_64-linux-gnu/libgfrpc.so.0(rpc_clnt_notify+0x1a4) [0x7fe077f91cc4] (-->/usr/sbin/glusterfs(+0xcada) [0x7fe078655ada]))) 0-: received signum (1), shutting down [2014-06-13 08:52:28.148513] I [fuse-bridge.c:5444:fini] 0-fuse: Unmounting '/var/www/shared/private/uploads'. My fstab contains: proc /proc proc defaults 0 0 /dev/xvda / ext4 noatime,errors=remount-ro 0 1 /dev/xvdb none swap sw 0 0 /dev/xvdc /var/lib/glusterfs/brick01 ext4 defaults 1 2 koraga:/private_uploads /var/www/shared/private/uploads glusterfs defaults,_netdev 0 0 Any ideas what's going on and/or how to fix it?

    Read the article

  • Find out the type of an automounted device

    - by Steve Bennett
    I'm working on a system (Ubuntu Precise) with a mount defined in /etc/fstab as follows: /dev/vdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 Originally I just wanted to find out if it's NFS (due to potential MySQL locking issues). Judging from man mount, it's not: If no -t option is given, or if the auto type is specified, mount will try to guess the desired type. Mount uses the blkid library for guessing the filesystem type; if that does not turn up anything that looks familiar, mount will try to read the file /etc/filesystems, or, if that does not exist, /proc/filesystems. All of the filesystem types listed there will be tried, except for those that are labeled "nodev" (e.g., devpts, proc and nfs). If /etc/filesystems ends in a line with a single * only, mount will read /proc/filesystems afterwards. But, out of curiosity now, how can I find out more about what type of device it actually is? (For context, this is a VM running on OpenStack. The device is a 60Gb allocation mounted from somewhere - but I don't know how.)` EDIT Including answers here: $ mount /dev/vdb on /mnt type ext3 (rw,_netdev) $ df -T /dev/vdb ext3 61927420 2936068 55845624 5% /mnt

    Read the article

  • Have an Input/output error when connecting to a server via ssh

    - by Shehzad009
    Hello I seem to be having a problem while connecting to a Ubuntu Server while connecting via ssh. When I login, I get this error. Could not chdir to home directory /home/username: Input/output error It seems like my home folder is corrupt or something. I cannot ls in the home folder directory, and in my usename directory, I can't cd into this. As root I cannot ls in the home directory as well or in any directory in Home. I notice as well when I save in vim or quit, it get this error at the bottom of the page E138: Cannot write viminfo file /home/root/.viminfo! Any ideas? EDIT: this is what happens if I type in these commands mount proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) /dev/mapper/RAID1-lvvar on /var type xfs (rw) /dev/mapper/RAID5-lvsrv on /srv type xfs (rw) /dev/mapper/RAID5-lvhome on /home type xfs (rw) /dev/mapper/RAID1-lvtmp on /tmp type reiserfs (rw) dmesg | tail [1213273.364040] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213274.084081] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213309.364038] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213310.084041] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213345.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213346.084042] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213381.365036] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213382.084047] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213417.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213418.084063] Filesystem "dm-4": xfs_log_force: error 5 returned. fdisk -l /dev/sda Cannot open /dev/sda

    Read the article

  • repair partition table

    - by m.sr
    Hallo. I've just overwritten my partition table of my system's hard disk. i made a cfdisk on the wrong device (/dev/sda instead of /dev/sdd), deleted all partitions, made one new primary spanning over the whole device, set its type to 07 (NTFS) and hit write. So here i am with my system running. Until i reboot, i hope/guess nothing will change - meaning: all my data is accessible (I'm currently making a dd-backup of the whole device and plan to make a .tar.gz-backup of the most important data later). I also backed up /proc/partitions, /proc/diskstats (even though i guess this is more about throughput and stuff like this ...) and /sys/block/sda/sda?/{start,size}. Some further things i know: 4 primary partitions 1st partition: ~100Mb, ext3, /boot 2nd partition: ~100Mb, "Win7 Boot Partition", ntfs(?) 3rd partition: ~20...30GB, Win7, ntfs 4th partition: ~20...30GB, luks-encrypted device The luks- de crypted device is a LVM-PV The /, /home & swap-partitions are all LVs on the (VG on the) above noted PV So my questions: What is the simplest way to just write the kernels partition table to the disk? What is the simplest way to take the above mentioned (and perhaps other I don't know of ...) data and generate the partition table? Are there any problems to take care of regarding to luks and/or lvm? Is there any data I should backup before rebooting (meanig stuff from kernel [ /sys/..., /proc/...] and so on, which could help me regenerate the partition table)? Thanks a lot! P.S.: debian sid, Kernel 2.6.34-1-amd64 from debian-experimental, 80GB Intel SSD

    Read the article

  • Refresh file access time under Linux / Discard disk read cache

    - by calandoa
    I am making use of the access time to analyse some build process, but it is not working the way I want: the access time is updated the first time I read the file, then it stays the same for a long while, or until the next reboot. For instance: $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 10:03 some_file $ grep abcdef some_file $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 11:24 some_file # The access time is updated # waiting a few minutes... $ grep abcdef some_file $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 11:24 some_file # The access time has not been updated :( I suppose that the file is buffered by Linux in the free memory, the only this copy is accessed the subsequent times for speed reasons. A solution would be to discard the buffers in memory. After searching some forums, I found: sync echo 1 > /proc/sys/vm/drop_caches echo 2 > /proc/sys/vm/drop_caches echo 3 > /proc/sys/vm/drop_caches But it is not working, it seems that it only sync up the write buffers, not the read ones. May be it is due to some custom kernel configuration on my distro (fedora 9)? Or I am missing something here? Is there a way to achieve this access time refresh? Note also that I do not want to simulate some writes on my entire file tree. Because I am using some makefile based build system, this will cause the entire project to be build again.

    Read the article

  • CentOS OpenVZ fail to boot after kernel update

    - by SkechBoy
    After upgrading to latest OpenVZ kernel CentOS server won't boot. When i try go boot the latest kernel server is stuck at this point: (note that images are taken from virtual kvm) http://i.stack.imgur.com/4lusz.jpg Then i try to start the server on some old kernels and than i get this error message: kernel panic - not syncing - attempted to kill init better shown on this image: http://i.stack.imgur.com/2SReF.jpg Here is some useful information fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2995.7 GB, 2995739688960 bytes 255 heads, 63 sectors/track, 364211 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004c4e4 Device Boot Start End Blocks Id System /dev/sda1 1 523 4199044+ 82 Linux swap / Solaris /dev/sda2 524 785 2104515 83 Linux /dev/sda3 786 261869 2097157230 83 Linux /dev/sda4 261870 364211 822062115 83 Linux /etc/fstab proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/sda1 none swap sw 0 0 /dev/sda2 /boot ext3 defaults 0 0 /dev/sda3 / ext3 defaults 0 0 /dev/sda4 /home ext3 defaults 0 0 and grub config file: title OpenVZ (2.6.18-274.18.1.el5.028stab098.1) root (hd0,1) kernel /vmlinuz-2.6.18-274.18.1.el5.028stab098.1 ro root=/dev/sda3 vga=0x317 selinux=0 initrd /initrd-2.6.18-274.18.1.el5.028stab098.1.img title OpenVZ (2.6.18-274.7.1.el5.028stab095.1) root (hd0,1) kernel /vmlinuz-2.6.18-274.7.1.el5.028stab095.1 ro root=/dev/sda3 vga=0x317 selinux=0 initrd /initrd-2.6.18-274.7.1.el5.028stab095.1.img title OpenVZ (2.6.18-194.8.1.el5.028stab070.4) root (hd0,1) kernel /vmlinuz-2.6.18-194.8.1.el5.028stab070.4 ro root=/dev/sda3 vga=0x317 initrd /initrd-2.6.18-194.8.1.el5.028stab070.4.img Any help is greatly appreciated Thanks.

    Read the article

  • When I restart my LXC environment, the container does not re-bind to the IP address

    - by RoboTamer
    The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

    Read the article

  • RHEL Java Application returns "No space left on device" but only 3% used

    - by FiveO
    My Java Application returns following Exception when saving a new file in /opt/wso2 on a CentOS 6.4: Caused by java.io.FileNotFoundException: ... (No space left on device) Caused by: java.io.FileNotFoundException: /opt/wso2/FrameworkFiles/trk_2014062500042488825_TRCK_PatfallHospis_pFromHospis_66601fb3-a03c-4149-93c3-6892e0a10fea.txt (No space left on device) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:212) at java.io.FileOutputStream.<init>(FileOutputStream.java:99) at com.avintis.esb.framework.adapter.wso2.FrameworkAdapterWSO2.sendMessages(FrameworkAdapterWSO2.java:634) ... 23 more But when I run df -a I can see that the partition still has plenty of space available: [root@stzsi466 wso2]# df -a Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_stzsi466-lv_root 12054824 2116092 9326380 19% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys devpts 0 0 0 - /dev/pts tmpfs 4030764 0 4030764 0% /dev/shm /dev/sda1 495844 53858 416386 12% /boot /dev/sdb1 51605436 1424288 47559744 3% /opt/wso2 none 0 0 0 - /proc/sys/fs/binfmt_misc [root@stzsi466 ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/mapper/vg_stzsi466-lv_root 765536 45181 720355 6% / tmpfs 1007691 1 1007690 1% /dev/shm /dev/sda1 128016 44 127972 1% /boot /dev/sdb1 3276800 6137 3270663 1% /opt/wso2 What is the problem here? Is it caused by the Java on CentOS 6.4? I have another server running Redhat REHL 6.4 and all works fine - same Java etc. Does anyone know of this problem?

    Read the article

  • Multiple logins with pam_mount means multiple (redundant) mounts ...

    - by Jamie
    I've configured pam_mount.so to automagically mount a cifs share when users login; the problem is if a user logs into multiple times simultaneously, the mount command is repeated multiple times. This so far isn't a problem but it's messy when you look at the output of a mount command. # mount /dev/sda1 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) //srv1/UserShares/jrisk on /home/jrisk type cifs (rw,mand) //srv1/UserShares/jrisk on /home/jrisk type cifs (rw,mand) //srv1/UserShares/jrisk on /home/jrisk type cifs (rw,mand) I'm assuming I need to fiddle with either the pam.d/common-auth file or pam_mount.conf.xml to accomplish this. How can I instruct pam_mount.so to avoid duplicate mountings?

    Read the article

  • centos install / partitioning

    - by ServerSideX
    I'm using NOC-PS to remotely install Centos 6.2 via KVM / IPMI. I'm going to install cPanel as well and they recommend this layout /boot (99MB) swap (2x server RAM) / (remainder) In the o/s install profile within NOC-PS software, it shows as this: part /boot --fstype ext2 --size 250 part pv.01 --size 1 --grow volgroup vg pv.01 logvol / --vgname=vg --size=1 --grow --fstype ext4 --fsoptions=discard,noatime --name=root logvol /tmp --vgname=vg --size=1024 --fstype ext4 --fsoptions=discard,noatime --name=tmp logvol swap --vgname=vg --recommended --name=swap By the time the default partition setup was done installing Centos, I get this [root@server005 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg-root 532G 907M 504G 1% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 243M 28M 202M 13% /boot /dev/mapper/vg-tmp 1008M 34M 924M 4% /tmp [root@server005 ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Fri Dec 7 18:47:24 2012 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg-root / ext4 discard,noatime 1 1 UUID=58b31aaf-5072-4fb1-a858-33bc316fa793 /boot ext2 defaults 1 2 /dev/mapper/vg-tmp /tmp ext4 discard,noatime 1 2 /dev/mapper/vg-swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 My question is, how should the NOC-PS install profile look like to get the recommended cPanel partitioning? The server has 16GB RAM, dual 600GB SAS drives and will be used for cPanel shared hosting.

    Read the article

  • Debian: Unable to mount a second drive as a subdirectory inside of another partition.

    - by jkndrkn
    Hello. I have the following /etc/fstab: # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 /dev/md1 / ext3 defaults,errors=remount-ro 0 1 /dev/md0 /boot ext3 defaults 0 2 /dev/md5 /home ext3 defaults 0 2 /dev/md3 /opt ext3 defaults 0 2 /dev/md6 /tmp ext3 defaults 0 2 /dev/md2 /usr ext3 defaults 0 2 /dev/md4 /var ext3 defaults 0 2 /dev/md7 none swap sw 0 0 /dev/sdc /home/httpd ext3 defaults 0 2 /dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/sdc1 /mnt/usb/backup-1 auto defaults 0 0 I am unable to get /dev/sdc/ to mount at /home/httpd/ on reboot. The /home/httpd/ directory exists. Mounting via mount -t ext3 /dev/sdc /home/httpd works just fine. Mounting via mount -a generates the following error message: mount: you must specify the filesystem type This is, incidentally, the same message that I see while booting. The error message goes away if I comment out the line in fstab starting with /dev/sdc.

    Read the article

  • Relinking a deleted file

    - by mbac32768
    Sometimes people delete files they shouldn't, a long-running process still has the file open, and recovering the data by catting /proc/<pid>/fd/N just isn't awesome enough. Awesome enough would be if you could "undo" the delete by running some magic option to ln that would let you re-link to the inode number (recovered through lsof). I can't find any Linux tools to do this, least with cursory Googling. What do you got, serverfault? EDIT1: The reason catting the file from /proc/<pid>/fd/N isn't awesome enough is because the process which still has the file open is still writing to it. A delete removes the reference to the inode from the filesystem namespace. What I want is a way of re-creating the reference. EDIT2: 'debugfs ln' works but the risk is too high since it frobs raw filesystem data. The recovered file is also crazy inconsistent. The link count is zero and I can't add links to it. I'm worse off this way since I can just use /proc/<pid>/fd/N to access the data without corrupting my fs.

    Read the article

  • Hungry hungry BIOS: why do I have less than 4 GiB of memory?

    - by Rhymoid
    I thought I had 4 GiB of memory, but just to be sure, let's ask the BIOS about that: ?: sudo dmidecode --type 20 # dmidecode 2.12 SMBIOS 2.6 present. Handle 0x000B, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0007FFFFFFF Range Size: 2 GB Physical Device Handle: 0x000A Memory Array Mapped Address Handle: 0x000E Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Handle 0x000D, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00080000000 Ending Address: 0x000FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x000C Memory Array Mapped Address Handle: 0x000E Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Alright, 4 GiB it is. But I can't use all of it: ?: cat /proc/meminfo | head -n 1 MemTotal: 3913452 kB Somehow, somewhere, I lost 274 MiB. Where did 6% of my memory go? Now I know the address ranges in DMI are incorrect, because the ACPI memory map reports usable ranges well beyond the ending address of the second memory module: ?: dmesg | grep -E "BIOS-e820: .* usable" [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dee7bfff] usable [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000117ffffff] usable I get pretty much the same info from /proc/iomem (except for the 4 kiB hole 0x000-0xFFF), which also shows that the kernel only accounts for less than 8 MiB. I guess 0x00000000-0x7FFFFFFF is indeed mapped to the first memory module, and 0x80000000-0xDFFFFFFF to part of the second memory module (a bunch of ACPI NVS things live between 0xDEE7C000 and 0xDEF30FFF, and the remaining 16-something MiB of that range are just 'reserved'). I guess the highest 0x18000000 bytes of the second memory module are mapped above the 4 GiB mark. But even then, there are two problems: 128 MiB (0x08000000 bytes, living somewhere between 0xE0000000 and 0xFFFFFFFF) are still completely unaccounted for. To note, my graphics card is on PCI-Express and (allegedly) has 1 GiB dedicated memory, so that shouldn't be the culprit. Did the BIOS screw up in moving the memory, leaving it partially shadowed by MMIO? Even with this mediocre explanation, I only 'found' 128 MiB. But /proc/meminfo is reporting a much larger deficit; where's the other 146 MiB? How does Linux count MemTotal?

    Read the article

  • Is it safe to format this partition?

    - by xanesis4
    On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

    Read the article

  • SqlCommandBuilder.DeriveParameters(command) and IsNullable

    - by Andrey
    I have written an O/R database wrapper that generates some wrapper methods for stored procs it reads from the database. Now I need to produce some custom wrapper code if an input parameter of a stored proc is defaulted to NULL. The problem is - I get stored proc parameters using: SqlCommandBuilder.DeriveParameters(command) and it doesn't bring parameter defaults. Is there any way to look up those defaults? Are they stored anywhere in the database? BTW, I'm using SQL Server 2008

    Read the article

  • Running Command via Java ProccesBuilder Different to Running the same in the Shell

    - by Tom Duckering
    I'm tearing my hair out trying to work out why the command I'm executing via Java using a ProcessBuilder & Process is not working. I run the "same" command at the Windows command line and it works as expected. It must be that they're not the same but I can't for the life of me work out why. The command is this: ccm start -nogui -m -q -n ccm_admin -r developer -d /path/to/db/databasename -s http://hostname:8400 -pw Passw0rd789$ The output is should be a single line string that I need to grab and set as an environment variable (hence the v. basic use of the BufferedReader). My Java code, which when it runs the command gets an application error, looks like this with entry point being startCCMAndGetCCMAddress(): private static String ccmAddress = ""; private static final String DATABASE_PATH = "/path/to/db/databasename"; private static final String SYNERGY_URL = "http://hostname:8400"; private static final String USERNAME = "ccm_admin"; private static final String PASSWORD = "Passw0rd789$"; private static final String USER_ROLE = "developer"; public static List<String> getCCMStartCommand() { List<String> command = new ArrayList<String>(); command.add("cmd.exe"); command.add("/C"); command.add("ccm"); command.add("start"); command.add("-nogui"); command.add("-m"); command.add("-q"); command.add("-n "+USERNAME); command.add("-r "+USER_ROLE); command.add("-d "+DATABASE_PATH); command.add("-s "+SYNERGY_URL); command.add("-pw "+PASSWORD); return command; } private static String startCCMAndGetCCMAddress() throws IOException, CCMCommandException { int processExitValue = 0; List<String> command = getCCMStartCommand(); System.err.println("Will run: "+command); ProcessBuilder procBuilder = new ProcessBuilder(command); procBuilder.redirectErrorStream(true); Process proc = procBuilder.start(); BufferedReader outputBr = new BufferedReader(new InputStreamReader(proc.getInputStream())); try { proc.waitFor(); } catch (InterruptedException e) { processExitValue = proc.exitValue(); } String outputLine = outputBr.readLine(); outputBr.close(); if (processExitValue != 0) { throw new CCMCommandException("Command failed with output: " + outputLine); } if (outputLine == null) { throw new CCMCommandException("Command returned zero but there was no output"); } return outputLine; } The output of the System.err.println(...) is: Will run: [cmd.exe, /C, ccm, start, -nogui, -m, -q, -n ccm_admin, -r developer, -d /path/to/db/databasename, -s http://hostname:8400, -pw Passw0rd789$]

    Read the article

  • SqlCommandBuilder.DeriveParameters(command) and IsNullable

    - by Andrey
    I have written an O/R database wrapper that generates some wrapper methods for stored procs it reads from the database. Now I need to produce some custom wrapper code if an input parameter of a stored proc is defaulted to NULL. The problem is - I get stored proc parameters using: SqlCommandBuilder.DeriveParameters(command) and it doesn't bring parameter defaults. Is there any way to look up those defaults? Are they stored anywhere in the database? BTW, I'm using SQL Server 2008

    Read the article

  • rules precedence in bison

    - by arbiadr
    Hi Here is the grammar rules: ProcessExpression : EventExpression "->" ProcessExpression | ProcessName ; Please can you tell me how can I tell to bison that the first rule has the highest precedence than the second one? I have tried: %nonassoc PROC %right "->" ProcessExpression : EventExpression "->" ProcessExpression | ProcessName % prec PROC; But without any result. Thank you.

    Read the article

  • masm division overflow

    - by Help I'm in college
    I'm trying divide two numbers in assembly. I'm working out of the Irvine assembly for intel computers book and I can't make division work for the life of me. Here's my code .code main PROC call division exit main ENDP division PROC mov eax, 4 mov ebx, 2 div ebx call WriteDec ret divison ENDP END main Where WriteDec should write whatever number is in the eax register (should be set to the quotient after the division call). Instead everytime I run it visual studio crashes (the program does compile however).

    Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >