Search Results

Search found 4909 results on 197 pages for 'board games'.

Page 163/197 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Hardware doesn't work some times

  - by Ali

  I have an Asus n51vf laptop. I bought it not long time ago (less than a month) and installed Windows 7 on it. Since that it wasn't new when I bought it, I don't know, if the problem was occuring before re-installing Windows 7. There are two problems, that might (or might not) have something to do with each other: Problem The less annoying problem is that the screen flickers ONLY on YouTube when scrolling and/or pausing/playing the video or moving the curser over the video. The second more timeconsuming problem is that some of the hardware doesn't work when I turn up the computer. Then I have to reboot the computer and try again. Example: I turn on the computer, and the touchpad doesn't work - I then reboot and it works again. This has so far happened to the screen (leading to a black screen), the keyboard and the touchpad. More frequently the mouse. What have I tried to do so far? I tried reeinstalling the touchpad driver (Synaptic Touchpad driver from Asus Support Page) - didn't help at all. I even tried reinstalling the driver when the non-responding mouse on startup-problem occured (using the keyboard), but it asked me to reboot and didn't help at all. I also installed (and reinstalled) the graphics driver; it's a GeForce GT 130M. Now, the problem never occurs spontaneously - it only appears when booting my computer. I can even use the computer for heavy tasks (games, multiple programs running etc.) with no problem at all. I suspect, that the problem is in some booting mechanism that fails: Maybe the Windows driver loading? Motherboard problems?

  Read the article

• Typical outbound port list for guest access?

  - by Steve

  I manage a weekly rental house that includes wireless Internet access. I've allowed all outbound ports on my router but my ISP has disabled my Internet access twice now because guests have downloaded (or served up) copyrighted content. So I'd like to institute some port filtering to discourage p2p sharing (see disclaimer below). But I don't want to inconvenience the 99.9% of folks who keep things above-board. My question is, what outbound ports are typically open for rental/hotel wireless Internet access, or where can I find such a list? TCP 80,443,25,110 at a minimum. Though my own email service uses 995 and 465 for SSL, some may use IMAP, I personally use SSH and FTP, so I'll open those. Roughly I figure I need to open access to privileged ports, and close 1024 & above. Is there a whitelist I should institute for commonly used high ports? And does it make sense to block UDP 1024 ? Disclaimer: I realize anyone replying to this message could circumvent the port filtering and share content to their heart's content. I do not need comprehensive p2p blocking, which requires more than a port whitelist. Anyone staying at the house shoulders the responsibility for their Internet use, per the rental contract. Also anyone savvy enough to circumvent the port filters would hopefully be savvy enough to use some sort of peer blocking, thereby preventing the ISP from taking down the service.

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• What would cause my Windows machine to seize?

  - by Coltin

  I run Windows XP SP2 on a Desktop I built (I know that doesn't provide much, but I can't say "on a Dell X103938R" or something). It has 'seized' about 7 times in its year and a half life. Everything freezes. I can't move the mouse cursor and the keyboard seems unresponsive. I can turn the monitor on and off and it will hold the last image. The light for the mouse is responsive if I move it. The keyboard lights change when pressed (cap locks, etc). I've waited upto ten minutes for a change, nothing. I haven't connected any activity to the seizing. It's happened when all I was "running" were fullscreen programs (games), just checking email, or once when I was sitting at my desktop (I was reading a book and when I tried to use the mouse, nothing). I've never been able to figure it out. I have to hard reset, and then its fine. It doesn't file system check or anything (not sure if Windows does that). No error when I load up the computer, nothing. If I had uTorrent open, it will have to recheck the torrent files to make sure they weren't corrupted though. (It's not always open when it seizes either). I'm using an AMD Athlon 5400+ with a NVidia GeForce 8600 GT, if that helps. I'm using two hard drives, 500Gb Wester Digital with a 1Tb Hitachi.

  Read the article

• System freezes during boot process

  - by slugster

  Hi everyone, i have a machine running Win7 Ultimate. It was running fine, then it just froze - all the stuff i was doing was still on the screen, but mouse and keyboard input was ignored, any animation that was happening on the screen stopped, the machine literally just froze. So i rebooted (power off button), from then on the machine will reboot, but it ultimately freezes again. The instance when this happens will vary - i have made it as far as the Windows login screen, but mostly it will do the POST, then give me the option to press F1 to continue or Del to enter BIOS settings (but of course pressing a key has no effect - it's frozen!). I have disconnected everything not necessary for the boot process, the only peripheral that remains attached is the keyboard. (even the network cable is disconnected). Prior to this the machine was operating fine. The install of Win7 is only 2 days old, and it was a fresh reinstall (i.e. not an upgrade or repair). Can anyone give me an indication of what may be wrong here? I'm not sure if this question should be here or on SuperUser, please migrate it if i have chosen the wrong board.

  Read the article

• System freezes during boot process

  - by slugster

  Hi everyone, i have a machine running Win7 Ultimate. It was running fine, then it just froze - all the stuff i was doing was still on the screen, but mouse and keyboard input was ignored, any animation that was happening on the screen stopped, the machine literally just froze. So i rebooted (power off button), from then on the machine will reboot, but it ultimately freezes again. The instance when this happens will vary - i have made it as far as the Windows login screen, but mostly it will do the POST, then give me the option to press F1 to continue or Del to enter BIOS settings (but of course pressing a key has no effect - it's frozen!). I have disconnected everything not necessary for the boot process, the only peripheral that remains attached is the keyboard. (even the network cable is disconnected). Prior to this the machine was operating fine. The install of Win7 is only 2 days old, and it was a fresh reinstall (i.e. not an upgrade or repair). Can anyone give me an indication of what may be wrong here? I'm not sure if this question should be here or on SuperUser, please migrate it if i have chosen the wrong board.

  Read the article

• What is the best VM for developing WPF apps from within OS X?

  - by MarqueIV

  All of my machines are Macs (Mac Pro, MacBook Pro, MacBook Air and Mac Mini (and Apple TV 2.0 too! :) ) but for my day-job, I develop .NET/WPF applications. Normally I just boot into Boot Camp and develop that way, which of course works great, but there are times when I need to simultaneously get to things on my Mac-side of the equation, so I've bought both VMware 3.1 and Parallels 6. Both work, however, even on my Mac Pro where I paid to upgrade to the better video cards (the NVidia 8600s I think vs. the stock ATI cards) the WPF performance bites!! Now this confuses me since both boast that they support not only hardware-accelerated OpenGL 2.1, but also hardware-accelerated DirectX 9 (VMware even allegedly supports DirectX 10!) via their respective virtual drivers and both can run 3D games just fine, even in a window. But even the simple act of resizing a WPF window that has a tiled background results in some HIDEOUS repainting and resizing behaviors. It's damn near closer to what you'd expect over RDP let alone a software-only renderer (forget accelerated hardware completely!) So... can anyone please tell me WTF WPF is doing differently? More importantly, how can I speed up the WPF performance? Should I switch to VirtualBox that also has support for DirectX? Or am I just gonna have to 'byte' the bullet (sorry... had to. So I like puns! Thank Jon Stewart!) and continue using Boot Camp?

  Read the article

• How to fix Quicktime video color problems on nVidia chipset and Windows XP?

  - by Matthew Glidden

  My laptop frequently plays video as if in very low-color mode. Though the sound remains clear, it looks terrible, showing only a few shades of red, blue, or yellow. (It's even worse than 8-bit color.) The problem doesn't happen consistently, so I'm looking for troubleshooting advice or known solutions. I use a Dell Latitude D620 laptop with Windows XP, on-board nVidia video chipset, Quicktime, and multiple monitors (laptop screen + VGA-connected LCD). Color problems happen in each application I tried, iTunes, a browser, and the Quicktime standalone player. It doesn't happen right after reboot, so could be from a sleep-wake cycle, or at least being on for an extended period. Google results suggest reinstalling nVidia drivers, which I've done several times with no change. I have found 2 workarounds. Reboot, sacrificing significant time and disrupting work In nVidia control panel, change color to 16-bit, and then back to 32-bit This happens with all video playback, so it's definitely not one corrupt file. I use workaround #2 consistently, but would love a longer-term solution.

  Read the article

• Best way to execute a command after Linux system halt

  - by Lukas Loesche

  Problem: The SSDs in our servers require a power cycle (i.e. off/on, not reset/warm reboot) after a firmware update. Thoughts: Using 'ipmitool chassis power cycle' I can cycle the server's power. However this would cut the power while the system is still running, filesystems are mounted, etc. What I basically want is a delayed power cycle so the system has a change to halt. But I guess that would have to be implemented on the server's IPMI board, so it's not really an option. My initial idea was to dynamically create a ramdisk containing the tool and libs and somehow integrate that into the halt process. I saw there's a /etc/init.d/halt, so that would be my starting point. Although I believe the kernel at some point in the shutdown process starts to kill off remaining processes. So I'm not even sure if that's a viable way. Question: What would be the best way to execute ipmitool (or any other command), after the system has halted and all regular filesystems are unmounted?

  Read the article

• Tri-head linux system with Xmonad: is it possible to have HW acceleration

  - by progo

  What means there exists to have three monitors, all controlled by Xmonad and have hardware 3D acceleration as well? I had the pleasure of using three monitors earlier this year, and while Xmonad and Xinerama handle three monitors easily, I had to throw in an extra display driver, and also let go of Nvidia's own TwinView (which is a hack on Xinerama). This left me with no HW acceleration and some flickering as double buffering wouldn't work with certain applications. However, the three monitors handle so beautifully that I had hard time coming back to two. I understand the easiest way to achieve HW-accelerated tri-head combo is to split into two Xorgs. I wouldn't be able to switch windows between the Xorgs, so I'm not really into this solution. What's more, having a cheap and old PCI card along with even slightly better PCIe seemed to slow things down. Even if I occasionally disabled the third monitor from Xorg configure, I couldn't get HW acceleration to work. Only after I physically disconnected the old PCI card, I could get the games back in business. Would a Matrox Dual/Tri-head2go and a powerful Nvidia GPU do the trick? I understand Xmonad can be configured to "believe" that a "single" (as Dualhead2Go will merge) 3360x1050 display is actually two different ones? So that Xmonad's Mod-w and Mod-e would work properly there.

  Read the article

• No headphone or speakers plugged in - Windows 7 issue

  - by Amit Ranjan

  I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

  Read the article

• Not able to find scripts present in /etc/profile.d directory [on hold]

  - by priya

  I am using Red Hat Linux 6.0 ... using davinchi board. I have to change system clock resolution so I am changing (HZ) env var. For this I have written script so that I can change HZ = 1000 n insert that script in /etc/profile.d and write code for loop in /etc/profile so that while running as usual /etc/profile can load the scripts present in /etc/profile.d. But when I am logging into the system at root level then showing error as "-bash: ./etc/profile.d/resolution.sh(my script name): No such file or directory Also here why it is showing ./etc and not /etc . Is something related to that?? Also I tried to add script in /etc/init.d but still no change in value of HZ takes place. Please tell where to change so that this env var can get changed. The script(resolution.sh) written has :- #!/bin/bash export HZ=1000 The content of /etc/profile which I entered is: if [ -d /etc/profile.d ]; then for i in /etc/profile.d/*.sh; do if [ -r $i ]; then .$i fi done unset i fi And the output of grep command is -rw-r--r-- 1 root root 535 Feb 4 2004 profile -rwxr-xr-x 2 root root 4096 Feb 2 2004 profile.d

  Read the article

• How to discover true identity of hard disk?

  - by F21

  I have 2 fake external hard drives that claim to have a storage capacity of 2TB. I pulled the enclosure apart and the hard drives seems to be refurbished ones with their labels replaced as Barracuda LP 2000 GB labels (the serial numbers on both labels are the same). Interestingly, one of the drives have 160G written on it with pencil. However, the counterfeiters seem to have done something to the firmware, because CrystalDiskInfo reports them as 2TB ST2000DL003 drives. I then delete the 1.81 TB partition in Windows disk management and tried to create a new one and format it. Once I get to this point, the drives would make some noise that is common to dying drives. I am not interested in using these drives for production, but I am interested in finding the true identity (manufacturer/serial number/model number, etc) and restoring it to their factory defaults with the right capacity. Can this be done without any special equipment? This would be an interesting learning exercise. Some pictures of the drives in question: Here are the screens from CrystalDiskInfo: Note the serial numbers are the same (these are 2 different drives!). How is this done? Did they have to tamper with the controller board? I would assume that changing the firmware doesn't change the serial number at all.

  Read the article

• HP G61 Laptop wont boot- display stays off, caps and num lock indicators blink repeatedly

  - by Benguy12

  I had my HP G61 laptop running in sleep for a while. When I came back to it about a half-hour later, it was no longer in sleep mode - the power light and the Wi-Fi indicator light were on (I keep Wi-Fi off becuase I use a wired connection) - but nothing was showing on screen. In fact, the display wasn't even turned on. So I let it sit for about 10 minutes but nothing happened. I did a force shut down and rebooted. Instead of a normal boot, the display didnt turn on, the Wi-Fi indicator was off, and the Caps Lock and Num Lock lights just blinked repeatedly. On the external keyboard i use, none of the light indicators were blinking or even on. I tried force shut-down again 10 times, then unplugged all connections except for the power cable (my laptop battery dosent hold a charge for more than 2 minutes, so I always must have a wall connection) and tried to boot again but still nothing happened. I unplugged the battery and even then nothing happened. I also tried booting with the disk drive open, and then with it closed again. On the time it was closed, I was able to successfully boot into Windows, but recieved a "Windows did not shut-down sucessfully" notice. Does anybody know why this may have happened? My PC's specs: Windows 7 Home Premium, 64-bit 4GB of physical RAM, 8GB of vRAM (on a flash drive) AMD Vision x64 processor (don't know any other specs about it) ATI Radeon graphics card, 392 MB DVD-R/W lightscribe drive 2 External hard-disks (first one is 1.5TB, second one is 1TB) custom boot-screen and boot-annimation Standard BIOS apps running before sleep: firefox 10.4 itunes 10.6 adobe photoshop extended CS5.1 rockstar games social club (running in background) microsoft powerpoint 2010 professional edition google chrome I was NOT running Aero or any fancy themes - I was using the normal windows classic theme. I have a desktop icon manager application called Stardock Fences that was also running (it runs as a service/process).

  Read the article

• Why is my connection slow?

  - by Jay R.

  I have a Dell Precision T5400 with a Broadcom 1Gb onboard NIC. For some strange reason, when I access machines on our local network, the best I can get is around 125KB/s download speed. My laptop that has a 10/100Mb NIC onboard usually gets around 300KB/s or better from the same network resource. Both machines are plugged into the same 1Gb switch which connects to our local network wall jack at 100Mb half duplex. There is also a printer plugged into the same switch at 100Mb full. The resource I'm using for the test is a 30MB zip file copied from a jetty webserver that is running as part of a cruisecontrol installation. The cruisecontrol installation is running WindowsXP with full real-time antivirus and Altiris patch management and inventory running. That stuff on its own is eating some of the download speed. I've seen the laptop reach into the multiple MB/s download speed before, but the desktop never seems to get past 125KB/s to 130KB/s. In WindowsXP, before I upgraded the driver in the desktop, it was that slow. In Fedora, it is still slow even though it appears to be using the same driver version as the upgraded Windows driver. The upgraded Windows driver is faster, but still not nearly as fast as the laptop. What gives? Any insight to improve the situation would be appreciated. Could it be that the BroadCom board just isn't that good, or the driver in linux is just not as good as the Windows one?

  Read the article

• Constant beeping

  - by Bogi Juul Peterson

  My computer has a problem with beeping. I'll first tell you how it started: One night I decided to watch a cartoon, and I took some water and food with me to eat while I watch. I fell asleep and when I woke up I had spilled water all over my keyboard. I didn't react quickly, because it went unnoticed for about 1 and a half hours. When I noticed, I quickly put my laptop on a radiator to try to dry it. When I turned the computer on there was a constant beeping sound. I didn't know what caused it, and I'm still not sure, but I think it has something to do with the USB hub. If I let the computer stand for some hours without any USB connections, it's fine, but when I put any kind of USB device in, it starts beeping. The laptop keyboard doesn't work so I have to have some kind of USB device connected to use the computer. The beeping is going on while I'm writing this and it makes my computer lag so much that it can make delays from the keyboard be from 1 second to 10 seconds. I need this computer because I don't have the money to buy a new one, and I have to use this computer for homework and games. The beeping is constant, with less than a second between beeps. If anyone has a solution, please help.

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• Blue screen error code 1000008e

  - by Kas

  I'm getting blue screens, mostly when trying to boot a program that required a lot of memory (games, photo editing software.) So far I've only managed to catch one set of error codes: BCCode: 1000008e BCP1: C0000005 BCP2: ADA393BA BCP3: E9BCEBC4 BCP4: 00000000 OS Version: 6_0_6002 Service Pack: 2_0 Product: 768_1 It's on a Sony VAIO Laptop VGN FW-41E, Vista OS service pack 2. Besides these codes it lists two 'temporary' files that were related with this crash: ...AppData\Local\Temp\WER-134925-0.sysdata.xml ...AppData\Local\Temp\WERDA66.tmp.version.txt When I googled these files some site said it was linked to a worm called 'yodo', but virus scans don't return any results (hitman pro, malware bytes, avast antivirus all turn up empty). Upon further searching about this yodo worm, I came across security stronghold where someone posted they had acquired this worm when downloading access and excel templates. Now, I actually did download templates for the same programs, they might have been the same, they may be related or I might be grasping at straws here. I have not noticed any issues other in performance as of late, just BSOD's when I start software that requires some memory, but I never had issues with these exact same programs before. Help and/or hints are required on how to actually figure out what's the root of this BSOD issue and how can I fix it. Do you reckon it's actually a virus? What program should be able to remove YODO worm stuff?

  Read the article

• SSD Drive not being recongized in BIOS

  - by chobo2

  Well I bought my first drive Mushkin Chronos 180GB and got it installed in my computer and loaded up. I went to windows 7 and initialized the drive and then I installed "SSDlife Free" and loaded it up and my the SSD drive came up said it was "powered on 3 times"(thought it was odd but then thought maybe some testing???). I then restarted my computer and loaded into Acronis. Went to my SSD drive and make a partition called windows(made a basic logical partition). I then loaded up Norton ghost and wanted to copy my current windows onto the SSD drive on the partition I made found out I could not do it through the recovery disk so I made a backup of my windows drive and wanted to then restore it onto the SSD drive. Came back an hour later when the backup was done. I tried to restore the it on my SSD drive and could not find the partition so I loaded up Acronis again and it did not see it. I then went to the bios and saw only my other hard drive. What I tried Tried uplugging and replugging in both sata and power cables. Tried using the power and sata cable from the working drive and giving it the ones that SSD drive were using. Tried Sata AHCI Mode (Intel ICH9 Southbridge) Tried SATA PORT0-1 NATIVE MODE (Intel ICH9 Southbridge) Nothing worked. Software / hardware Windows 7 ultimate Gigabyte S-Series GA-P35-DS3L Mother board I hope someone has some ideas on why it is not being recognized.

  Read the article

• Are These Parts compatible?

  - by ell

  I have never assembled a PC before, although I have taken an old one apart and replaced a few parts in others here and there so I have (very) limited experience. I have been looking to make a pc and here are the parts I might buy: Foxconn P45AL Intel P45 (Socket 775) DDR2 Motherboard (with onboard sound I believe) Gigabyte GeForce GTX 460 OC 768MB GDDR5 PCI-Express Graphics Card Already have 2 1gb sticks of dual channel DDR2 memory Intel Core 2 Quad Q8400 LGA775 'Yorkfield' 2.66GHz 4MB-cache Processor Samsung SpinPoint F3 1TB SATA-II 32MB Cache Hard Drive Antec Dark Fleet Series DF10 Gaming Enclosure – Black I already have monitor, mouse, keyboard and DVD/CD drive Akasa Freedom Power 1000W Modular Power Supply I have never done this before so feel free to laugh at me for getting something obvious wrong, forgetting a vital component etc. but is all of this compatible? And have I gone overkill on the PSU, if so, please recommend one. Thanks in advance, ell. EDIT: Added PSU which I forgot to mention EDIT: I would be using this to surf the internet, write e-mails, chat, word process, play games such as team fortress 2 & spring rts (at highest graphics hopefully), some 3d modelling in blender, some opengl programming, and image editing in GIMP.

  Read the article

• RAM being displayed is lesser than the actual in my Windows 7

  - by Prateek Somani

  I am using Windows 7 and Ubuntu on the same machine. Earlier I had 3 GB of RAM,but now the Windows is displaying just 1 GB of RAM. Please also find the output of the free command in my Ubuntu : total used free shared buffers cached Mem: 1008208 904808 103400 5736 13516 239596 -/+ buffers/cache: 651696 356512 Swap: 3127292 10252 3117040 Has the swap memory consumed my 2 GB of RAM? Will I be able to use the whole of 3GB of the RAM in my Windows? Regards, Prateek Update : I tried to run the lshw command and I got the following output : *-memory description: System Memory physical id: 1b slot: System board or motherboard size: 1GiB *-bank:0 description: SODIMM DDR3 Synchronous 1067 MHz (0.9 ns) product: HMT112S6BFR6C-H9 vendor: Hynix physical id: 0 serial: 2C71D069 slot: Bottom - Slot 1 size: 1GiB width: 64 bits clock: 1067MHz (0.9ns) *-bank:1 description: SODIMM DDR3 Synchronous 1067 MHz (0.9 ns) [empty] product: 16JSF25664HZ-1G4F1 vendor: Micron physical id: 1 serial: FD421821 slot: Bottom - Slot 2 width: 64 bits clock: 1067MHz (0.9ns) Why it is able to detect the vendor/product name of the bank-1 RAM, why can't it detect the RAM size and other details ? Has my RAM got faulty?

  Read the article

• Intel ICH9/10R raid 5 drive failure

  - by davpen

  About a year ago I was using the native Intel ICH9R Raid 5 an Intel P35 based motherboard. The system was running Vista x64 and when one of the drives failed Vista blue screened on boot until I had figured out which drive had failed and removed it (a rather nerve racking hit and miss affair). The same thing happened some months later on another similar system so it wasn't a once off. This wasn't the robust raid 5 drive failure behavior that I would have hoped for and expected. I moved to Highpoint Rocketraid 2300 and haven't had any problems although I have yet to have a drive fail with this set up. But I am now looking to build a new system based on an i7 and Windows 7. At the moment Highpoint doesn't have drivers for Windows 7 so I am considering moving back to the on board Intel Raid. Yes I know I that I might get away with using the Vista drivers but I don't really want to take that chance with critical data. The question then is has anyone else experienced a drive failure with Intel raid and how did the OS and drivers handle it? Is it safe to go back?

  Read the article

• Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

  - by sputnik

  I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

  Read the article

• Disabling Laptop (PB TJ-75) faulty card reader Linux

  - by Gab

  My problem comes from that my laptop [PB TJ-75] has a faulty Alcor card reader. It’s 100% sure, the device is dead and unusable whatever the OS is. It cannot be disabled in BIOS [latest: Vendor: Phoenix Technologies LTD Version: V1.26 Release Date: 05/04/2010]. If I could take it apart from the main board easily, and if with that, the system would never look again for it, I’ll be very happy! Is it possible, has anyone ever tried this? Or maybe, replacing the BIOS with a more open one, which let you disable the card reader. Does this exists? Here's what I've tried to disable it so far. In Win7, I choose ‘disable’ in device manager and that’s ok. If not, the device keeps on appearing and disappearing and lot of resources are used. In Lubuntu 13.04, I got extra boot time, with the msg:'sdb, assuming drive cache, etc.’ I tried other distros (isos booted by grub). I can boot Puppy, Gparted, and Redobackup apparently without any problem. I cannot boot Debian, live or install + tried Crunchbang and Tails. I got a loop :’usb device, scsi n+1 blabla‘. I tried "nousb", no result, I have blacklisted EHCI, no result, then usb_storage module, better boot time in Lubuntu, with just the message "...data transfer failed", better shutdown time too. But, no way to use usb storage medias. In Debian, it ends with BusyBox prompt. Is it possible to just disable that Alcor card reader? Does it have a specific module? Is there a special kernel boot option that I missed? Does it have something to do with kernel recompiling, and if yes, how to do with isos? Programming a driver which says everything is ok (out of my comprehension for the moment)? Disabling device by vendor id? What is the best way?

  Read the article

• CloneZilla Broke My System? Ubunut Installation Lost After Running CloneZilla

  - by nicorellius

  I just read through this post and tried to get my installation back using this answer to no avail. What happened to me is this: I spent an hour or more reading through the CloneZilla docs. I thought I was ready to test it out so I burned the disc with the ISO image on it and ran it. The system I used was Ubuntu 10.04, 32-bit. Everything seemed to go fine. I made a clone of my first partition and copied it to my second partition. I followed the instructions, removed the disc and rebooted my system. At this point, I would expect to have two bootable Linux installations, identical to one another. However, upon booting, I got this error message: error: no such device: 4cf1a6ef-xxxx-xxxx-xxxx-4e3a3ce92bcd error: file not found I booted from a Live Ubuntu disc and was able to see my to partitions: 4cf1(1) and 4cf1(2) (abbreviated, because the volumes have long numbers to identify them). The 50 GB partition, on which the original Ubuntu installation sits is the number and the second partition (175 GB) is the same number with an "_" at the end. I could browse the disc partitions and see the files, but I'm not sure what to do next. I know there is a way to restore my grub loader and actually boot either of these installations, but my Linux know-how is limited. Can I edit the boot loader file to fix this problem? The only clue I have is CloneZilla said something about making a new GRUB but I thought it was going to basically modify it so I could boot either installation. Not sure what happened. I am going to look through this post for the time being to see if I can learn anything to help my problem. But I thought that, since this happened as a result of using CloneZilla, it may be a unique question for this board.

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >