Search Results

Search found 8232 results on 330 pages for 'i dont wanna die'.

Page 165/330 | < Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >

• Media center consumes all available memory when attempting to play music off of a server

  - by RCIX

  I have Windows 7 Ultimate, and recently, when i try to play a song off of my Twonky Media Server/Windows Media Connect (based on an HP WHS with an Atom), it plays choppily. When i open Resource Monitor, it shows that after ordering the music to play, memory usage rapidly spikes to consume most, if not all, of the available memory on my system (excluding a couple hundred megabytes in standby). Why does it do this and is there anything i can do to stop it? Edit: it happens when I attempt to browse the server's music, not just when i play music. Edit 2: the "ehshell" process is what consumes the memory, appears to me something specific to media center. Moreover, the ehshell process doesn't die in this case. Edit 3: It only happens when browsing my Twonky library, and not my Windows Media Connect.

  Read the article

• Why don't mails show up in the recipient's mailspool?

  - by Jason

  I have postfix dovecot running with local email system on thunderbird. I have two users on by ubuntu, mailuser 1 and mailuser 2 whom i added to thunderbird. Everything went fine, except the users dont have anything on their inbox on thunderbird and sent mails dont get through. Im using maildir as well. Checking /var/log/mail.log reveals this This what is happining: Restarting postfix and dovecot and then sending mail from one user to another user... I believe this line is the problem May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] Why is it not connecting ? What could be wrong ? /var/log/mail.log May 30 18:30:21 dovecot: imap: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: imap: Server shutting down. in=467 out=475 May 30 18:30:21 dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Dovecot v2.2.9 starting up (core dumps disabled) May 30 18:30:54 dovecot: imap-login: Login: user=<mailuser2>, method=PLAIN, rip=::1, lip=::1, mpid=12638, TLS, session=<xUfQkaD66gAAAAAAAAAAAAAAAAAAAAAB> May 30 18:31:04 postfix/master[12245]: terminating on signal 15 May 30 18:31:04 postfix/master[12795]: daemon started -- version 2.11.0, configuration /etc/postfix May 30 18:31:55 postfix/postscreen[12803]: CONNECT from [127.0.0.1]:33668 to [127.0.0.1]:25 May 30 18:31:55 postfix/postscreen[12803]: WHITELISTED [127.0.0.1]:33668 May 30 18:31:55 postfix/smtpd[12804]: connect from localhost[127.0.0.1] May 30 18:31:55 postfix/smtpd[12804]: 1ED7120EB9: client=localhost[127.0.0.1] May 30 18:31:55 postfix/cleanup[12809]: 1ED7120EB9: message-id=<[email protected]> May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: from=<[email protected]>, size=546, nrcpt=1 (queue active) May 30 18:31:55 postfix/local[12810]: 1ED7120EB9: to=<mailuser2@mysitecom>, relay=local, delay=0.03, delays=0.02/0.01/0/0, dsn=2.0.0, status=sent (delivered to maildir) May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: removed May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] May 30 18:31:55 dovecot: imap-login: Login: user=<mailuser1>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=12814, TLS, session=<sD9plaD6PgB/AAAB> This is my postfix main.cf See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination myhostname = server mydomain = mysite.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $mydomain mydestination = mysite.com #relayhost = smtp.192.168.10.1.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.10.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all home_mailbox = Maildir / mailbox_command= All ports are listening tcp 0 0 *:imaps *:* LISTEN tcp 0 0 *:submission *:* LISTEN tcp 0 0 *:imap2 *:* LISTEN tcp 0 0 s148134.s148134.:domain *:* LISTEN tcp 0 0 192.168.56.101:domain *:* LISTEN tcp 0 0 10.0.2.15:domain *:* LISTEN tcp 0 0 localhost:domain *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 localhost:953 *:* LISTEN tcp6 0 0 [::]:imaps [::]:* LISTEN tcp6 0 0 [::]:submission [::]:* LISTEN tcp6 0 0 [::]:imap2 [::]:* LISTEN tcp6 0 0 [::]:domain [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 [::]:smtp [::]:* LISTEN tcp6 0 0 localhost:953 [::]:* LISTEN

  Read the article

• shinken/nagios discriminative between warning alert and critical alert

  - by SWdream

  i using shinken for my monitoring system. Now, i have a problem when i configure shinken notification. My purpose is to discriminative between notification for warning state and critical state of check service: with warning state: + time to send alert from 8h = 18 h everyday, via email and sms + notification_interval is 60 minutes (Re-notify about service problems every hour) with critical state: + time to send alert : all time (24 x 7), via email and sms + notification_interval is 30 minutes Please show me how to solve my problem! I have tried the following: i configured: + contact templates: define contact{ name warning-contact ; The name of this contact template register 0 ; DONT REGISTER THIS DEFINITION - ITS NOT A REAL CONTACT, JUST A TEMPLATE! host_notifications_enabled 1 define contact{ service_notifications_enabled 1 email shinken@localhost can_submit_commands 1 notificationways email_warning, sms_warning } define contact{ name critical-contact ; The name of this contact template register 0 ; DONT REGISTER THIS DEFINITION - ITS NOT A REAL CONTACT, JUST A TEMPLATE! host_notifications_enabled 1 service_notifications_enabled 1 email shinken@localhost can_submit_commands 1 notificationways email_critical, sms_critical } + time poriod templates: define timeperiod{ timeperiod_name warning alias Normal Work Hours monday 08:00-18:00 tuesday 08:00-18:00 wednesday 08:00-18:00 thursday 08:00-18:00 friday 08:00-18:00 saturday 08:00-18:00 sunday 08:00-18:00 #exclude 24x7 } define timeperiod{ timeperiod_name 24x7 alias 24_Hours_A_Day,_7_Days_A_Week sunday 00:00-24:00 monday 00:00-24:00 tuesday 00:00-24:00 wednesday 00:00-24:00 thursday 00:00-24:00 friday 00:00-24:00 saturday 00:00-24:00 #exclude workhours } + notification way templates: define notificationway{ notificationway_name email_warning service_notification_period warning host_notification_period warning service_notification_options w host_notification_options d,u,r,f,s notification_interval 60 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-email ; send service notifications via email host_notification_commands notify-host-by-email ; send host notifications via email } define notificationway{ notificationway_name email_critical service_notification_period 24x7 host_notification_period 24x7 service_notification_options c,r host_notification_options d,u,r,f,s notification_interval 30 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-email ; send service notifications via email host_notification_commands notify-host-by-email ; send host notifications via email } define notificationway{ notificationway_name sms_warning service_notification_period warning host_notification_period warning service_notification_options w host_notification_options d,u,r,f,s notification_interval 60 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-sms ; send service notifications via sms host_notification_commands notify-host-by-sms ; send host notifications via sms } define notificationway{ notificationway_name sms_critical service_notification_period 24x7 host_notification_period 24x7 service_notification_options c,r host_notification_options d,u,r,f,s notification_interval 30 ; Resend notifications every 30 minutes service_notification_commands notify-service-by-sms ; send service notifications via sms host_notification_commands notify-host-by-sms ; send host notifications via sms } + my contacts define contact{ use warning-contact contact_name thanhwarn email xxxx pager xxxx ; contact phone number } define contact{ use critical-contact contact_name thanhcritical email xxxxx pager 01689xxxx ; contact phone number } + and define service: define service{ use generic-service service_description check_ram host_name graphite contacts thanhcritical, thanhwarn check_command check_nrpe!check_ram } but my shinken system don't send alert. i don't understand this. please show me where I went wrong! thanks all!

  Read the article

• System will only boot into a Live CD with core disabled in BIOS and ACPI off.

  - by CookieOfFortune

  I have a system that was running a Q6600 and Windows 7 RC. It crashed last night into a BSOD with a MACHINE_CHECK_EXCEPTION. Now it does that every time it boots into Windows. I tried using my Ubuntu Live CD, but the kernel would error out, the stack trace showed something along the linse of "Can not synchronized to one of the CPUs". Working from this, I enabled the "Limit CPU to 3 cores" option in my BIOS and tried again. This time, it seemed to have died after an ACPI call, so I disabled that during the boot and now it is running from the Ubuntu Live CD, showing 2 cores. Does anyone here think I have any hope or is it simply a CPU waiting to die? EDIT: 1 core now.

  Read the article

• Suspected power supply issue? PC repeatedly whirs for some seconds and then dies.

  - by benwebdev

  I've come home today and switched on the PC I've built a few months ago only for the machine to whir for a few short seconds and then die. It repeats this until I disconnect the power lead. Nothing is output to the screen and this cut out happens very quickly after switching it on. What could this be and how could it be fixed? Is it the power supply? I'm in despair :-( My spec is below, everything is new and was bought and assembled within the last 6months, system has been fantastic until now. Power Supply: 620W CoolerMaster Real Power M620 Motherboard: Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Processor: Intel Core i7 930 2.80GHz @ 4.00GHz RAM: 6GB DDR3 OS Windows 7 64bit Sapphire HD 5770 Vapor-X 1GB Graphics card 1TB Hitachi HDD 720GB Seagate Barracuda HDD 350GB Seagate Barracuda HDD EMu 0404 PCI Soundcard D-Link PCI-E wireless card Samsung DVD RW drive

  Read the article

• Apache Tomcat 6.0.29 startup causing Win XP SP3 reboot

  - by Liam

  Some of our Windows XP Developer machines die (black screen - no ping) when starting up Tomcat from a console. This only happens if the Tomcat debug console window is displayed (not minimised). When minimised, the startup / run is successful. I've checked for Tomcat logs and the crash sessions produce empty (zero bytes) tomcat log files. No system logs exist and no crash dump is created even though this is enabled in the Windows settings. The machine is dual screen and another machine with the same image has the same issue. The only clue is just before the crash, one of the monitors the system reports "Cannot display video mode 1280x1024" (approximate error, didn't write it down). Is there a way I can get Windows to produce log files of this crash session? Beyond running Tomcat as a service / minimised window, how can I fix (or even investigate)?

  Read the article

• Kill ssh background process after disconnect / timeout?

  - by keflavich

  I frequently use ssh tunnels to access VNC sessions on remote machines, but this is on my laptop so the connections break when I put it to sleep for the night. If I then try to re-open the connection in the morning, I have to manually kill the ssh session, otherwise I get this error: bind: Address already in use channel_setup_fwd_listener: cannot listen to port: 1202 Could not request local forwarding. The SSH command I'm using is this: ssh -N -C -f -L 1202:localhost:5900 name@server What's the best way to have the ssh tunnel die when it disconnects? Or reset?

  Read the article

• How to delete files quicker than rm -rf?

  - by Byakugan

  Is there any way how to delete folder/files quicker than with command rm -rf? It seems my disc is filled with bilions of files (sessions of php5) which were not deleted in cron so I need to delete them manually but it takes hours and it is still not helping reducing the amount. Thank you. My command: rm -rf /var/lib/php5/* Tried also these commands: find /var/lib/php5 -name "sess_*" -exec rm {} \; And perl -e 'chdir "/var/lib/php5/" or die; opendir D, "."; while ($n = readdir D) { unlink $n }'

  Read the article

• hardware: delay and distinct 'click' before hard drive access

  - by matt lohkamp

  I have a windows 7 box stashed away in my closet, containing (among other things) 2 big HDDs linked together as a mirrored volume - basically a super lazy NAS / media server. I've noticed that when that drive is accessed (whether locally, on the machine itself, or remotely, from another computer, or my xbox, for example) there's a noticeable pause, and then from the computer itself, a 'click!' noise, after which the drive is accessed; e.g. open \\computername\shared\, wait 2 seconds, hear 'click!' and then see files appear in windows explorer. Any ideas? Otherwise the drive preforms normally - is it a windows thing? a HDD-about-to-die thing? Or a "yeah that always happens, you've just never noticed it before" thing?

  Read the article

• Wireless card overheating?

  - by Sidney

  Ok, so I've had my laptop for several years (I wanna say 4, but possibly more), it's a Toshiba Satellite. I'm running Linux mint 15, and am having a strange new issue, after several hours of running my wireless stops. It can SEE wireless networks, but refuses to connect to any of them. (On a sidenote, connecting to a router with a cable at this point works fine) The fact that it can SEE the networks make me think the card is in good condition, and it's software related The fact that it works for several hours before booting me makes me think perhaps the transmitter is getting too hot. I don't use my laptop in dusty environments, and keep it on an elevated surface (alternatively, I actively try not to let it sit on soft surfaces where the vents get covered). I spray out the cpu fan about once a year with compressed air about once a year, so I really don't think the insides should be too dirty. Finally, unfortunately, sensors only gives me CPU temps, but they run about 40-50 degrees C, which from my understanding is perfectly normal for an I3. Does anyone have any suggestions on what I can do to determine the root cause of this?

  Read the article

• DD-WRT Router Can't hold a connection after initial setup...

  - by AC

  Struggeling with my new DDWRT router (Buffalo WZR-HP-G300NH) configuration. I configured it using one machine while comparing the settings on my existing Linksys WRT54GL on another machine. To the best of my knowledge, I've set it up the same way as my Linksys, but DDWRT has so many other options. After configuring it, I plugged it into the modem, VOIP device & my network. I see the phones come back online. However after a few minutes, it seems I lose the outbound connection (phones die and I can't get out over HTTP). What's confusing me is it works for a few minutes, then it fails. No idea what to look for. Ideas?

  Read the article

• Any way to stop VMWare workstation from dropping SSH connections?

  - by oljones

  I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

  Read the article

• centos cron job running php file

  - by user50946

  I have a php file under php called test.php set to run every 5th minute of the hour. When ever I run the file manually (by going to the web browser and runnint the path) it works fine. But when the cron job tries to run it I get the error message my cron job is #### Delete Records 5 * * * * /var/www/html/phpsysinfo/cronUpdateLeadBucketOnEnergycAlliance.php my phpfile is (path : /var/www/html/phpsysinfo/phpfile) <?php require("dbconnect.php"); $sql = mysql_query("DELETE FROM list where status <> 'LEAD'") or die(mysql_error()); ?> and the error that I get is: /var/www/html/phpsysinfo/phpFile.php: line 1: ?php: No such file or directory /var/www/html/phpsysinfo/phpFile.php: line 2: syntax error near unexpected token `"dbconnect.php"' /var/www/html/phpsysinfo/phpFile.php: line 2: `require("dbconnect.php"); thanks

  Read the article

• mosh-like port forwarding

  - by Marc Merlin

  This is on linux, connecting to linux servers: I love mosh, but it doesn't support port forwarding, and likely won't for a while since it's been almost a year now and it hasn't happened yet. port forwarding over ssh is great, but because my laptop moves between networks several times a day, my ssh sessions die, and so do the port forwards. I could script/hack something to detect hung ssh and reconnect to get my port forwards back, but before I do this, is there another way to do long lasting port forwards when your source IP changes several times daily (because you go on different networks)? I'm thinking an ssh over UDP would do the trick but of course ssh is over TCP.

  Read the article

• Computer only booting after POWER ON/OFF 10 times or more?

  - by Jan Gressmann

  Hi fellow geeks, recently my computer started to behave like an old car and won't start up anymore unless I flip the power switch repeatedly. What happens when I power it on: CPU fans spins briefly and very slowly, then it stops Same with GPU fan No BIOS beeps or HDD activity Screen stays black After turning it on and off for like 10 times, it'll eventually boot like normal and run smooth without any problems what-so-ever. But I'm worried it might eventually die completely. Anyone know the most common cause of this? Maybe I should just leave the computer powered on? :)

  Read the article

• what to do when ctrl-c can't kill a process?

  - by Dustin Boswell

  Ctrl-c doesn't always work to kill the current process (for instance, if that process is busy in certain network operations). In that case, you just see "^C" by your cursor, and can't do much else. What's the easiest way to force that process to die now without losing my terminal? Summary of answers below: Usually, you can Ctrl-z to put the process to sleep, and then do "kill -9 process-pid", where you find the process's pid with 'ps' and other tools. On Bash (and possibly other shells) you can do "kill -9 %1" (or '%N' in general) which is easier. If Ctrl-z doesn't work, you'll have to open another terminal and kill from there.

  Read the article

• login as rsh in rhel 6 without entering password

  - by cartmancakes

  I need to be able to login to a RHEL 6 server using rsh (please don't flame me about security, it's irrelevant in this particular instance) as root without having to enter a password. My procedure for setting this up works great in RHEL 5.x, but does not work in RHEL 6. I suspect this has something to do with PAM, but I'm inexperienced with how to use PAM. Can someone help me with this? /etc/pam.d/rsh auth required pam_rhosts.so auth required pam_nologin.so account include common-account password include common-password session required pam_loginuid.so session include common-session /etc/pam.d/rlogin auth required pam_nologin.so auth [user_unknown=ignore success=ok ignore=ignore auth_err=die default=bad] pam_securetty.so auth sufficient pam_rhosts.so auth include common-auth auth required pam_mail.so account include common-account password include common-password session required pam_loginuid.so session include common-session Thanks!

  Read the article

• pdflush hanging on Amazon EBS drives when using multi-GB files - any workaround?

  - by rhh

  Hello, When I run gunzip on a 1.7GB file (which generates an 8GB file) on an EBS volume, pdflush freezes after gunzip runs and the CPU hangs indefinitely at 100% IO Wait. Here's the output from 'ps aux | grep pdflush'. Note the D status root 87 0.0 0.0 0 0 ? D 06:18 0:00 pdflush root 88 0.0 0.0 0 0 ? D 06:18 0:00 pdflush The only solution is to kill the pdflush processes. The processes don't die immediately either. This problem is repeatable and happens with new instances. I'm running 2xlarge instances and I have way more RAM free than is being used (i.e. /proc/meminfo shows 20+GB MemFree) Has anyone found a workaround to this problem in the past? Thanks for any thoughts. Robert

  Read the article

• Squid stale-while-revalidate not working when max-age=0

  - by Wiliam

  Squid 2.7 always reaches backend, expected is to reach backend using stale-while-revalidate only when cache expires, not when client triggers max-age=0. Script: <?php header('Cache-Control: public, max-age=10, stale-if-error=200, stale-while-revalidate=500'); header("Last-Modified: " . gmdate("D, d M Y H:i:s") . " GMT"); sleep(2); die("OK"); And squid config: # http_port public_ip:port accel defaultsite= default hostname, if not provided http_port 80 accel defaultsite=mydomain.com # IP and port of your main application server (or multiple) cache_peer 127.0.0.1 parent 8000 0 no-query allow-miss originserver name=main # Do not tell the world that which squid version we're running httpd_suppress_version_string on # Remove the Caching Control header for upstream servers header_access Cache-Control deny all #header_access Last-Modified deny all # log all incoming traffic in Apache format logformat combined %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %Hs %<st "%{Referer}>h" "%{User-Agent}>h" %Ss:%Sh access_log /usr/local/squid/var/logs/squid.log combined all cache_effective_user squid refresh_pattern . 10080 90% 999999 ignore-no-cache override-expire ignore-private icp_port 0

  Read the article

• what to do when ctrl-c can't kill a process?

  - by Dustin Boswell

  Ctrl-c doesn't always work to kill the current process (for instance, if that process is busy in certain network operations). In that case, you just see "^C" by your cursor, and can't do much else. What's the easiest way to force that process to die now without losing my terminal? Summary of answers below: Usually, you can Ctrl-z to put the process to sleep, and then do "kill -9 process-pid", where you find the process's pid with 'ps' and other tools. On Bash (and possibly other shells) you can do "kill -9 %1" (or '%N' in general) which is easier. If Ctrl-z doesn't work, you'll have to open another terminal and kill from there.

  Read the article

• What's the most reliable (i.e. time-proof) solution for organizing photos?

  - by digitxp

  I pooled together my photos from an old external hard drive, various Picasa Web caches, flickr, flash drives, and an old computer. They're all on my external hard drive, using extremely creative labeling, like allpictures pixix pix2 images familyphotos and so on (hey, I was 7 when I organized them last). My computer's hard drive can die at any minute, and the external is new but who knows what that means? I am planning to start reorganizing these picture, probably by face or time. I have Bridge CS5, Picasa, etc., but which one is the most likely to not crash and burn like my Vista laptop did with a ZIP file filled with pictures of a funeral?

  Read the article

• Is it possible to view Facebook news feeds page by page rather than loading it all as I scroll?

  - by oscilatingcretin

  If you want to scroll through your Facebook news feed (be it on the main feed, your personal feed, or in groups) to older parts, you have to scroll to the bottom, wait for the ajax load of the next part of the feed, and repeat. The problem with this is that, if you're scrolling down very far, the HTML document just gets bigger and bigger until your browser starts to die due to the overload of resources brought on by added HTML, text, and even images. This pretty much sets a limit to how far back you can scroll. Clicking on months and years on your personal feed has the same effect of cumulatively adding feed segments to the HTML document. I notice that this month/year feature is not available on the main feed and for groups. If there were a way to literally page through the feed so that only a single page's worth of feed data is loaded at a time, that would make scrolling through it much more doable.

  Read the article

• using trickle to slow down browser

  - by tester

  according to trickle's man page, http://linux.die.net/man/1/trickle i can limit the download speed of a process, e.g. trickle -u 10 -d 20 ncftp to Launch ncftp(1) limiting its upload capacity to 10 KB/s, and download capacity at 20 KB/s. how would I go about limiting google-chrome or firefox with trickle? Edit: For those of you asking why I asked such an obvious question, I tried trickle -u 10 -d 20 firefox and I'm getting an error trickle: Could not reach trickled, working independently: No such file or directory firefox opens right after, but is definitely not rate limited...

  Read the article

• Error code 2503 - Cannot install software on Windows 7 (64Bit)

  - by SixfootJames

  A short while ago, I had my hard drive die on me and at the same time my 1Tb backup drive! I took it back to the guy I bought the PC from and although the backup drive could not be recovered, he managed to get my machine working again by making a minor change in the BIOS which then got it out of that continuous loop it found itself in after multiple BSOD episodes. Everything seems to be working fine but yesterday when I tried to save something from Google Chrome, I got and insufficient permission problem and when I try to install software, I get an error of 2503. I have already followed the suggestions here but none of this worked for me. Any suggestions would be appreciated. EDIT: This started happening after I tried running a number of tests to get the machine working, including a previous restore point.

  Read the article

• Best format for hard drive for Windows and Mac?

  - by Neil

  I have a 500 GB USB External Hard Drive. I need four partitions on it, for the following purposes: 160 GB for a bootable backup of my Mac. 160 GB for a bootable backup of my Windows. 11 GB for a bootable Snow Leopard Install Disk Rest as for file storage. Now I need a partition table which will get recognised on both Windows and Mac, without needing extra software on Windows, which will let me keep bootable copies of both OS'es, but let me access the file storage from both OS'es. Currently, I have a GUI Partition Table, with Mac OS Extended (Journaled) Partitions for the two backups, Mac OS Extended for the Install Disk, and NTFS for the file storage. While this gets recognised perfectly on my Mac, thanks to an NTFS for Mac driver from Paragon, when connected to Windows, the drive is detected by the machine (listed in Safely Remove USB), but not recognised in Windows Explorer unless I install MacDrive, which is not feasible for me to install on public Windows Machines I might wanna access my storage area on. Can someone recommend the best combination of formats and software/drivers to get this done seamlessly?

  Read the article

< Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >