Search Results

Search found 171496 results on 6860 pages for 'not joe bloggs'.

Page 166/6860 | < Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >

• Windows 7 System File Checker (sfc) not working

  - by Andrew

  I have a strange problem with Windows 7 RTM. I'm running Ultimate 64-bit edition. Whenever I run sfc /scannow I get this error: Windows Resource Protection could not start the repair service. My research so far has told me that I need to set the Windows Module Installer and Windows Installer services' startup types to Manual. They already were, so I manually started those services and tried again. No luck. I've even booted into my Windows 7 repair disc and tried running sfc /scannow from that. All I get is this: A repair operation is already pending. Restart and try again. History: I'm trying to run sfc because I am unable to open any images in Windows Photo Viewer. Whenever I try, I get the error "Class not registered." I believe the problem started after I installed Gladinet, but I can't be sure. I've uninstalled Gladinet, but the problem remains. System Restore was disabled (yes, I know I'm stupid - you don't have to remind me). Please help. Thanks.

  Read the article

• pptp server 2003 hands out gateway from nic not dhcp server

  - by Pete

  I have created a pptp RRAS server for a handful of clients to connect to. I would like them to use the servers default gateway (.1) for internet access. They are able to successfully connect (& see LAN) but it then cuts them off the internet. I understand that all internet traffic would be routed through the pptp server but that's ok since I have enough pipe. The problem seems to be that: the clients gateway shows as their assigned RAS ip. The clients assigned DNS settings seem to be what is set to the servers nic not what I have specified in dhcp (which is the same server). DHCP relay agent properties points to the nic DHCP is running on (192.168.100.163). .1 is gateway in nic hw properties & dhcp. I have different dns secondary & third entries on my nic properties than what dhcp is configured for. The problem is that I have a 10.10.1.x network that people can not see if they uncheck the gateway option but, they are then unable to see our other hosted sites on the internet.

  Read the article

• Samba share will not connect (was working yesterday)

  - by David Gard

  I have a CentOS websver with a Samba share set up (\\webserver\websites). I was connected to this share just yesterday without issue, but today my Windows 8 PC will not connect to it. I've also tried making a connection from Windows 7 and Windows XP, all without success. I initially tried restarting my computer, but that did not work. I then tried restarting the Samba service on the webserver (service smb restart), and when that failed I restarted the webserver. All of that was to no avail, and I still cannot connect to the share. The webserver is contactable from my PC (and the others I tried), as the websites it hosts work fine and I'm able to Putty to the server. When connected to the webserver, I can see that Samba is running by using service smb status - service smb status smbd (pid 4685) is running... nmbd (pid 4688) is running... Can anyone please help me to get this share working? Here is my full Samba config (/etc/samba/smb.conf) - [global] workgroup = MYGROUP server string = Samba Server %v log file = /var/log/samba/log.%m max log size = 50 security = user encrypt passwords = yes socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192 local master = no [websites] comment = Websites browseable = yes writable = yes path=/var/www/html/ valid users = dgard

  Read the article

• Cronjob not Running

  - by Pete Herbert Penito

  I have a bash script that looks like this: #!/bin/sh PID=`ps faux | grep libt | awk 'NR==2{print $2}'` STATUS=`ps faux | grep libt | awk 'NR==2{print $1}'` if [ "$STATUS" = "ec2-user" ]; then echo "libt already killed" else sudo kill $PID echo "libt was killed" fi sleep 5 cd /home/ec2-user/libt sudo ./libt I have saved this file as restart.sh and when I run it like ./restart.sh, it does what its supposed to (kills the libt process and restarts it). However, now I am trying to automate the process by using cron. So I made a cron job that I want to run every 6 hours that looks like this 0 */6 * * * /home/ec2-user/restart.sh When I run "crontab -l" I can see this print so I know it's been added properly. I should mention that the service does not have the ability to be restarted, (like "service ... restart") the process ID needs to be found, killed and then the start script needs to be ran. I have found that this cronjob is not working, I'll log onto the box and I can tell by looking at the logs that no restart has occurred. What am I doing wrong? What can I do to troubleshoot? Any advice would help, this is my first cron job :) Thanks!

  Read the article

• bind would not work unless allow-query is "any"

  - by adrianTNT

  I have this in /etc/named.conf, I commented the default values and set my own under it. My domain would not load in browser unless I set allow-query to "any", is this OK, what should I edit? If is localhost or 127.0.0.1; 10.0.1.0/24; domain would not load. I tried the 127.. thing because it mentioned it here: http://wiki.mandriva.com/en/Testing:Bind Bind version is 9.7.0-P2-RedHat-9.7.0-5.P2.el6_0.1 OS is CentOS 6.0. options { // listen-on port 53 { 127.0.0.1; }; listen-on port 53 { any; }; //listen-on-v6 port 53 { ::1; }; listen-on-v6 port 53 { any; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; //allow-query { localhost; }; allow-query { any; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; };

  Read the article

• GPO startup script not copying files

  - by marcwenger

  I created a GPO startup script to execute for computers in a specific AD container. The script takes a file from the AD netlogon share and places it on a directory on the computer. Given the right permissions (ie: myself) can execute the script just fine and the file copies. But it doesn't work on startup - the file does not copy over from the AD server. The startup script should run as localsystem (am I right?). So the question is why do the files not copy on startup? Could it be because of: Is it permissions of the local system user? Reading the registry is problematic on startup? Obtaining files from the AD netlogon folder is problematic on startup? Am I missing it completely? My test machine does have the registry key and local directories as described in the script. I myself have standard user permissions on the test machine. AD server is Windows 2008, test client is Windows XP SP3 (and soon to be Windows 7, which I assume permissions issues will be inevitable) Dim wShell, fso, oraHome, tnsHome, key, srcDir Set wShell = WScript.CreateObject("WScript.Shell") Set fso = CreateObject("Scripting.FileSystemObject") key = "HKLM\Software\Oracle\Oracle_Home" On Error Resume Next orahome = wShell.RegRead(key) If err.Number = 0 Then tnsHome = oraHome + "\" + "network\admin\" srcDir = wShell.ExpandEnvironmentStrings("%logonserver%") + "\netlogon\UpdatedFiles\" fso.CopyFile srcDir + "file1.ext", tnsHome, true End If Side note: To ensure that the script is properly deployed, I purposely put some errors in the script, and on the next startup the error message appeared. So I know the GPO is deployed properly.

  Read the article

• Dropped WD External Harddisk, now it's shown as "Not initialized"

  - by Phelios

  So, the WD my passport external harddisk is dropped, and after that, the computer is unable to read it anymore. I was hopping if I can just find another case to try if the harddisk is still readable, but looks like the hard drive itself is not a normal SATA or PATA drive. I think it's modified. So, I can't find another case that I can try on. In the computer, I still can see the drive in the "Disk Management", but it's shown as Uninitialized, no size, and no drive letter. I've also tried a couple of recovery tools. Some can't detect at all, there is one (find and mount software) that can detect but shows 0 size. None of them can recover the data. WD is willing to replace it with a new one, but I still need to recover the data. Any way I can recover the data? UPDATE: I tried initialized it from the windows Disk Manager, but it give error "The request could not be performed because of an I/O device error."

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• SBS2011 Standard DNS suddenly not resolving some domains

  - by Matt

  Suddenly today I am unable to resolve common domains like serverfault.com, facebook.com; but other domains like google.com, cnn.com work fine. This is on a client machine (Win7 Pro) connected to an SBS2011 Standard domain. The only DNS server is the SBS2011 server. The same domains work fine on all client PCs I have tried, and the same ones do not work. Using nslookup, I get 'no such domain' errors for facebook.com, and the correct DNS entries for the ones that do work. When I add Google's Public DNS to my client PC as a backup (primary = local SBS server, secondary = 8.8.8.8), everything works fine for my client PC, but querying from the SBS server directly or from other client PCs are broken (so I don't believe it's a firewall issue). My main question is how can I see what servers the SBS2011 server queries if it doesn't know about a domain? There is nothing in our firewall logs that say it blocked any DNS-based packets, but I also wanted to query based on the IP/FQDN on the servers that the SBS server was likely to contact to find out about facebook.com for example. Update 23/05/2012: It appears DNS is working again this morning for the affected websites. Both the DC on its own and all client PCs can once again access the websites that were not loading last night, as well as the websites that were working. I haven't changed anything overnight, so it appears that there was some kind of temporary glitch, but I can't understand what would have caused it on the network.

  Read the article

• Mac dev folder missing, SSH not working

  - by SamGoody

  A few days ago, SSH stopped working. When I try logging in a get the following message: PTY allocation request failed on channel 0 stdin: is not a tty fatal: unrecognized command '' Connection to 74.52.61.194 closed. Web searches have shown me that there might be something wrong with /dev/std. But my computer lacks a /dev/ drive. There is an Alias to /dev/ [hidden, but I've revealed hidden files to do this search], but when I try to open it I am told that it cannot find the folder it is aliasing. Now, many a web search tells me that without a dev folder, the computer doesn't work, but it does seem to work, except the SSH. Also, are there any tools that can save my SSH preferences so that I don't have to, each time, type out the username@adrees, password, path all of which are long and complex? Not looking for a Filezilla type client, there are many of those. Looking for a command line like putty, that lets me use bash on the remote client. Am on Macbook Pro, latest version of Tiger.

  Read the article

• CentOS 6.5 new Kernel not active after reboot

  - by Kristofer

  Today I was running some yum updates and wanted to verify that everything went through fine by making sure I had a new kernel. To my surprise I noticed that CentOS was still running 2.6.32-431.5.1.el6.x86_64 even though it looked as though 2.6.32-431.23.3.el6 was installed. Indeed 2.6.32-431.23.3.el6 shows up in /etc/grub.conf but not in the upstart boot options. Any ideas why? In the update log it says: ---> Package kernel-firmware.noarch 0:2.6.32-431.5.1.el6 will be updated ---> Package kernel-firmware.noarch 0:2.6.32-431.23.3.el6 will be an update Could this be the reason? What does "will be an update" mean? My /etc/grub.conf: # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/VolGroup00-root # initrd /initrd-[generic-]version.img #boot=/dev/vda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu password --encrypted $1$auui(i$sODM4ni/Zts9IlMWu.wWF/ title CentOS (2.6.32-431.23.3.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.23.3.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.23.3.el6.x86_64.img title CentOS (2.6.32-431.5.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.5.1.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.5.1.el6.x86_64.img title CentOS (2.6.32-431.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.el6.x86_64.img

  Read the article

• dd on entire disk, but do not want empty portion

  - by Jonathan Henson

  I have a disk, say /dev/sda. Here is fdisk -l: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0000e4b5 Device Boot Start End Blocks Id System /dev/sda1 * 1 27 209920 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 27 525 4000768 5 Extended Partition 2 does not end on cylinder boundary. /dev/sda5 27 353 2621440 83 Linux /dev/sda6 353 405 416768 83 Linux /dev/sda7 405 490 675840 83 Linux /dev/sda8 490 525 282624 83 Linux I need to make an image to store on our file server for use in flashing other devices we are manufacturing so I only want the used space (only about 4gb). I want to keep the mbr etc... as this device should be boot ready as soon as the copy is finished. Any ideas? I previously had been using dd if=/dev/sda of=[//fileserver/file], but at that time, my master copy was on a 4gb flash ide.

  Read the article

• nginx not starting at reboot after gitlab installation

  - by Luis Masuelli

  I installed nginx (1.6) in ubuntu server (14.04). After that, I installed gitlab. I didn't realize it came with its own nginx. I uninstalled gitlab later. After installing gitlab, my first nginx began to never start at boot as a service. This means: If I hit sudo netstat -anp I don't see the corresponding entry in 0.0.0.0:80. If I hit sudo nginx -s reload and then sudo netstat -anp I see the corresponding entry I mentioned. I thought I could fixing it by doing: sudo update-rc.d nginx remove sudo update-rc.d nginx defaults After removing gitlab, but it did not help me (i.e. after reboot, nginx does not automatically start). I revised the /etc/init.d/nginx just to see that $DAEMON is still /usr/sbin/nginx. Question: What should I check to see the problem here (or: what could the problem be)? sudo nginx -s reload works with no problems at all.

  Read the article

• torrent downloads not showing on Squid log

  - by noobroot

  hello, i have just a few months working as sysadmin, hence i still have lots to learn, first thing id like to do is as follows: We have an OpenBSD 4.5 box acting like firewall,dns,cache etc, the box has 2 network cards, one conected directly to the internet and the other to our switch, i used to work with sarg for the log analysis but then changed to the much faster free-sa. I use a daily free-sa report to check the bandwidth usage and report our top 5 bandwidth consumers (3 days a week being #1 and you will be buying the pizzas :D, we are a small company ~20 so we are very familiar). this was working really good until recently, one of us required to download some stuff via torrent (~3GB) and since the pizza rule is active for non-work related downloads, he told me (verified) that his download was indeed work related so i would dismiss that 3GB off his quota, but to my surprise the log didnt showed that 3GB, since his ip consumption was only around 290MB. More recently, since the FIFA world cup started, we know that some of the employees are watching the match's streaming, we know it and we dont care about it since, like already stated, we are a small company so we dont have restrictive policies, we all can chat, watch youtube, download anything we want BUT we are only allowed 300MB a day otherwise you'll get in the top5-pizza-board, anyway, that streaming consumption is also not showing in the free-sa reports. So my question is, why is these data being excluded from the reports? im thinking that the free-sa reports list only certain types of things but im also thinking if are the squid logs the ones that are not erm... logging these conections. Any help, guide, advice or clarification is appreciated.

  Read the article

• bind9 - forwarders are not working

  - by Sarp Kaya

  I am experiencing an issue with bind. If i want to resolve any domain name that is on the zone file. It works fine. However, when I try to resolve anything that does not belong to the zone file. I know that actual DNS servers that are being forwarded are working fine. But somehow bind9 fails to use them. The content of /etc/bind/named.conf.options is: options { directory "/var/cache/bind"; forwarders { 131.181.127.32; 131.181.59.48; }; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; I have also tried to use only one ip address and it still did not work. also the content of /etc/bind/named.conf is: include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; So there is no problem with including options file. Any recommendations for fixing this problem?

  Read the article

• What can be a reason for phpMyAdmin login to be not working (not at all, no reaction on submit)?

  - by Ivan

  When I open "http://localhost/phpmyadmin/", enter "root" as the user name and my MySQL root password and press go, then if I was using Firefox, I was getting offered to download index.php file (of a zero length), if I was using Opera 11, it said "Connection closed by remote server". Following recommendations I've removed all packages related to phpMyAdmin, PHP, MySQL and Apache and then reinstalled them step-by step (instead of just issuing apt-get install phpmyadmin and relying on the system to install the whole LAMP stack via dependencies as I've done before). The only change I've got was Firefox to stop offering to download index.php - now when I press Ok to submit my password, it just doesn't show any visible reaction at all. What may the reason be and how to fix it? I use up-to-date Xubuntu 11.04. Reinstalling the whole LAMP stack and phpMyAdmin did not help, neither did removing AppArmor. I've tried to use SQLBuddy instead, but there's exactly the same problem. So, I think, the problem is not in phpMyAdmin but in MySQL, Apache or something. MySQL seems to work if I use command line to access it. Apache & PHP seems to work also, as the login page of phpMyAdmin displays correctly.

  Read the article

• Browsers behaving very strangely/not working in Windows Vista SP 2

  - by Kim_guest

  Sorry, that I'm posting this as a guest, but I couldn't log in. Maybe you can help me. I had a virus and gave this inspiron 1525 laptop to a computer expert, who removed it. I think he reinstalled Windows, because when I got it back IE 7 was installed. So after 3 hours I installed SP 1, SP 2, IE 9 and Google Chrome. First when there was only SP 1 and IE 7 installed, I could only use Google in IE, and I had copy the links download links of the updates (Update center didn't work) over to Google Chrome to download it there, because I couldn't do that in IE. Now I can't use Google at all, but strangely Bing works. Also I can display certain pages, but not all (I could open StackExchange, but not the login page; that's why I'm posting this as a guest). Another strange thing is, that now a webpage either works in both browsers (I couldn't install Opera, because the installer says it can't download the files) or in none. It is a 32 Bit system. It would be nice if you could help! I hope I will be even able to post this question...

  Read the article

• ERROR: Not enough space?

  - by dsmoljanovic

  Now this is a very unspecific question. I'm trying to figure out what this message would mean. Here is the story behind it: I'm installing Oracle enterprise manager cloud control (12c r3) on Solaris 10 (5/09). Installer opens up, i enter all needed information and at the last step click Install. It immediately crashes with only "ERROR: Not enough space" written in log and console and nothing else. Now, this could be java error or Solaris error? I'm thinking it's happening either when it starts to copy files or when it tries to launch a process that would do that. What space is it referring to? disk (have ehough), swap (also), memory (yep)... Any ideas are helpful. Edit: i found this exception in the oraInventory logs: oracle.sysman.oii.oiic.OiicInstallAPIException: Not enough space at oracle.sysman.oii.oiic.OiicAPIInstaller.initInstallSession(OiicAPIInstaller.java:2165) at oracle.sysman.oii.oiic.OiicAPIInstaller.initOUIAPISession(OiicAPIInstaller.java:790) at oracle.sysman.install.oneclick.EMGCOUIInstaller.prepareForInstall(EMGCOUIInstaller.java:676) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext$1.run(EMGCSummaryDlgonNext.java:243) at java.lang.Thread.run(Thread.java:662) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext.actionsOnClickofNext(EMGCSummaryDlgonNext.java:1067) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at oracle.sysman.install.oneclick.EMGCUtil.performonClickOfNextForClass(EMGCUtil.java:399) at oracle.sysman.install.oneclick.EMGCUtil.performPageLevelValidationsForSilentInstall(EMGCUtil.java:367) at oracle.sysman.install.oneclick.EMGCInstaller.prepareForSilentInstall(EMGCInstaller.java:1459) at oracle.sysman.install.oneclick.EMGCInstaller.main(EMGCInstaller.java:1553) disk status: bash-3.00$ df -h /tmp Filesystem size used avail capacity Mounted on swap 8.1G 2.7G 5.4G 33% /tmp bash-3.00$ df -h /u01 Filesystem size used avail capacity Mounted on / 275G 28G 244G 11% / swap: root@gs12emcc # swap -s total: 18306040k bytes allocated + 3837808k reserved = 22143848k used, 5712664k available

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Xen virtual host can reach some sites but not others

  - by Tun H S Lee

  Okay, this is killing me. Debian Squeeze, Xen 4.0, brand new install. No iptables rules whatsoever except for the ones added by the default xen bridge script. Dom0 can reach the entire world, no problems. DomU can receive packets from some hosts, but not from others. For instance, if I ping Host A, it works fine. If I ping Host B, the DomU reports 100% packet loss. The hosts are random, but consistent (even after reboots). I can see no pattern to why some work and others don't. In fact, in some cases, different virtual hosts on the same server (an other server at a different data center) are divided; some work and others do not. I can reboot (DomU or Dom0 too) and the same hosts will work or fail as before. If I tcpdump on the Host B while pinging from the DomU, everything looks fine. It sees the echo request coming in and says it's sending one back. However, if I tcpdump peth0 on the Dom0, it never sees the echo reply. Any ideas what could be happening? I'm tearing my hair out here.

  Read the article

• Why not block ICMP?

  - by Agvorth

  I think I almost have my iptables setup complete on my CentOS 5.3 system. Here is my script... # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP For context, this machine is a Virtual Private Server Web app host. In a previous question, Lee B said that I should "lock down ICMP a bit more." Why not just block it altogether? What would happen if I did that (what bad thing would happen)? If I need to not block ICMP, how could I go about locking it down more?

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• .htaccess with godaddy not working in subdomain

  - by explorex

  Hi, i have a site uploaded to shared subdomain (which is inside a folder). and htaccess is not working. please get details from here. EDIT::copied from stack overflow Hi, i uploaded as website to a subdomain, and every page is not working except the front page please check it here. what could be the possible reason? i shoud have 8 pages in front level and many more on admin level but i am getting 404 error as you can see, does anyone has idea or suggestion? UPDATE:: .htaccess file RewriteEngine On RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] RewriteRule ^.*$ index.php [NC,L] UPDATE to url rounting i do have few url router like below BUT i dont have any default router $router->addRoute( 'get-destination', new Zend_Controller_Router_Route('destination/get/:id/:dest-name', array( 'controller' => 'destination', 'action' => 'get', 'id' => 'id', 'dest-name' => 'dest-name' )) ); just to make look cooler and on my navigation (which is loaded from xml i have) something like <nav> <home> <label>HOME</label> <controller>index</controller> <action>index</action> <route>default</route> </home> since i was getting url problem from where url was routed and please check phpinfo at http://websmartus.com/demo/globaltours/public_html/phpinfo.php

  Read the article

• Exchange emails not delivering for one user

  - by Cylindric

  We have an Exchange infrastructure going through a migration from 2003 SP2 (call it ExOld) to 2010 (ExNew). All users are now on the new server, but mail is still being directed to ExOld until testing is complete. ExNew sends emails directly to the internet. For one particular user, emails don't seem to be being reliably delivered, but the odd thing is that it's not all emails. I can see external emails in his inbox. If I send an internal email it works fine. If I send an email from Gmail to him it doesn't get through. If I telnet from outside to ExOld I can send an email to him. If I telnet from outside to ExNew I can send an email to him. This is a transcript that results in a successful send: 220 ExOldName Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Mon, 22 Oct 2012 10:55:26 +0100 EHLO test.com 500 5.3.3 Unrecognized command EHLO test.com 250-ExOldFQDN Hello [MyTestExternalIp] 250-TURN 250-SIZE 250-ETRN 250-PIPELINING 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-CHUNKING 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XEXCH50 250 OK MAIL FROM:[email protected] 250 2.1.0 [email protected] OK RCPT TO:[email protected] notify=success,failure 250 2.1.5 [email protected] DATA 354 Start mail input; end with . Subject:Test 1056 Test 10:56 . 250 2.6.0 Queued mail for delivery quit 221 2.0.0 ExOldFQDN Service closing transmission channel Emails go through Symantec Cloud, but their "Track and Trace" shows the messages going through, with a "delivered ok" log entry. 2012-10-22 09:19:56 Connection from: 209.85.212.171 (mail-wi0-f171.google.com) 2012-10-22 09:19:56 Sending server HELO string:mail-wi0-f171.google.com 2012-10-22 09:19:56 Message id:CAE5-_4hzGpY2kXFbzxu7gzEUSj5BAvi+BB5q1Gjb6UUOXOWT3g@mail.gmail.com 2012-10-22 09:19:56 Message reference: 135089759500000177171130001194006 2012-10-22 09:19:56 Sender: [email protected] 2012-10-22 09:19:56 Recipient: [email protected] 2012-10-22 09:20:26 SMTP Status: OK 2012-10-22 09:19:56 Delivery attempt #1 (final) 2012-10-22 09:19:56 Recipient server: ExOldIP (ExOldIP) 2012-10-22 09:19:56 Response: 250 2.6.0 Queued mail for delivery I'm not sure where to look on the old (or new) server for information as to where the mails are ending up.

  Read the article

• Copy Database Wizard fails on creation of view into another not-yet-copied database

  - by user22037

  Update - I found that doing a manual detach/reattach using MSDN article "How to: Move a Database Using Detach and Attach (Transact-SQL)" got around this issue. I'll just be creating a script to dettach and reattach but do the file copies manually. Any info on how to overcome the problems with the wizard would be helpful in the future. I am in the process of moving around 20 databases from our current server to a new one. When performing the copies however I have found that some databases can not copy if they have views into other databases that have not yet been copied to the target system. The log file generated says "failed with the following error: "Invalid object name" in reference to the database in the view. If I first copy just the database referenced in the view and then in a separate step copy the database over containing the view it is successful. However some other database have views into each other so can't just adjust the order in which the copy occurs. Is there any way to ignore this error and just allow everything to copy?

  Read the article

< Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >