Search Results

Search found 18336 results on 734 pages for 'home office'.

Page 173/734 | < Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Route through site-to-site VPN not working

  - by Jonathan

  I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

  Read the article

• Trouble printing to local printer when connected to VPN with split-tunneling enabled

  - by Marve

  I'm a volunteer network admin for a multi-tenant non-profit office space. One of our new tenants uses a VPN to connect to remote resources using RRAS and Small Business Server 2008. They also have a local network printer for the workstations in our office. When connected to the VPN, they cannot print to the local printer. I informed their network admin that they need to enable split-tunneling to fix this. Their network admin enabled split-tunneling, but apparently printing still didn't work. He told me that I need to open port 1723 on our office firewall to allow it to work. I'm just a novice administrator and not familiar with RRAS, but this doesn't sound right to me and I haven't been able to find anything on the web to validate it. Additionally, my understanding of split-tunneling is that it is handled entirely by the VPN client and should work irrespective of firewall settings. Is my understanding of the situation incorrect? What steps should I take to resolve this problem?

  Read the article

• Setting up VPN with Snow Leopard Server and Linksys router

  - by SueP

  I'd like to get VPN going so I can log in to the office securely from home. I'm using Snow Leopard machines everywhere, and currently have Airport Extremes set up at home and at the office. I have a mac mini with Snow Leopard Server that I'm going to move to the office to act as my server. I just bought a Linksys 4-port router because it says it does VPN (model RVS4000). My problem is, I don't have a clue how to set this thing up, and the more reading I do, the more confused I get. Do I need two of these routers, one at each end? My laptop and iPad claim they can do VPN, so I was assuming I only needed one VPN router? At this point, I literally don't know what questions to ask, or where to plug this thing in. Presumably, between the modem and the airport, but...? If somebody can walk me thru some really basic setup, I'd be very grateful. Right now, I feel like going outside and screaming for a while. But that might attract the local cougar, and after the prints I saw on the arena this afternoon, I don't want to draw its attention. :-)

  Read the article

• Synchronize Dreamweaver over an SSH tunnel using an SFTP connection

  - by Aeo

  Maybe... Just maybe... I'm asking too much here. Maybe I'm even barking up the wrong tree. I'm looking to essentially have Dreamweaver establish an SSH tunnel to one machine, and then use that connection to synchronize a site that is on another machine entirely. Now for some details: We've got two connections here at work. We've got our office connection for day to day business, and then we've got some fancy connection hosting our web servers upstairs. For the most part they've been mutually exclusive until recently. We had been establishing an SFTP connection to synchronize our web sites by going out over the office connection to the web and coming back in over the fancy connection to our servers upstairs. Recently -ish, we established a LAN connection to one of our servers that makes a pleasant change in VNC connection quality. Thanks to Vinagre, this makes it really easy to connect to any of our servers over this LAN connection via SSH tunnel for VNC. However, in spite of that new addition of a LAN connection, we still synchronize over the 'net. Out the office connection and in on the fancy one upstairs. I'm looking to change this. I'd like to get Dreamweaver to first tunnel over our LAN connection to the servers, and then go from there to whatever connection it needs to. Am I asking too much? The current set up: Dreamweaver is installed on Windows XP which is running within VirtualBox on top of Ubuntu 10.10. The network connection for VirtualBox is currently made in NAT mode, but could easily be switched to a Bridged Connection should it need be. The LAN connection is to 1 of 5 servers running CentOS 5.

  Read the article

• iPhone all day meeting request bug?

  - by RodH257

  We've come across a bit of a weird bug in the office. our office is closing for a week or so over christmas, and our admin staff sent a meeting request to everyone in the office to go from 5pm on the 23rd of December until we return to work at 8.30 on the 5th. However there was some confusion, as if you look at the image below, the same meeting request is showing up with different start times for some people. While most people get the 5pm date, for others it shows up as an all day event! Staff have been planning their activities for the 23rd only to find out that their calendar is wrong and they are required to work. With some investigation, we noticed that all of the people with the incorrect time own iPhones or iPads. So perhaps they accepted the meeting on their phones, and it has put the meeting in wrong? There are people with the correct one that have iPhones, but perhaps they are on ios4 still, or perhaps they didn't accept the meeting request on their phone. has anyone else come across this error at all? is there a fix?

  Read the article

• Creating a Logical network diagram

  - by user273284

  Im a student and I have been assigned the task of creating a logical network diagram for the following scenario There are 2 buildings, the first is the head office and the second is the branch. The data centre is in the head office, it contains domain controller, mail server, file server and a web server. it provides wired and wireless access to the staff. the branch building is new and it does not have a network. The two buildings must be connected using a VPN connection. The branch building will not have any servers but just network devices that will provide the connectivity, the users in the branch building will be connected to the head office over the VPN. I had created a diagram based on this scenario, but my teacher rejected it saying that it does not follow Cisco hierarchical Model and the servers were not placed correctly in the diagram. I just wanted some help in this matter so that I Can create my network diagram correctly. If anyone could upload a picture of how the logical diagram should be for this scenario will be helpful, any other resources would also be great.

  Read the article

• Watchguard Firebox "split" fibre optic line into 2 interfaces

  - by fRAiLtY-

  We have a requirement on our Watchguard Firebox XTM505 to be able to split our incoming external interface, in this case a fibre optic dedicated leased line, 100/100. We use the line in our office of approx 30 machines however we also re-sell to an external company who utilise it to provide wireless internet solutions to the public. The current infrastructure is as follows: Data in (Leased Line) - Juniper SRX210 managed by ISP - 1 cable out into unmanaged Netgear switch - 1 cable into our firewall and office network, 1 cable to our external providers core router managed by them. We have been informed that having the unmanaged switch in the position it is poses a security risk and that a good option would be to get our Watchguard Firewall to perform the split, by separating our office onto a trusted interface, and by "passing through" the external line to their managed router. It is alleged that the Watchguard is capable of doing this and also rate limiting the interfaces, i.e. 20mbps for the trusted interface and 80mbps for the "pass-through", however Watchguard technical support don't seem to be able to understand what we're trying to achieve. Can anyone provide any advice on whether this is possible on a Watchguard device and how or perhaps if there's a better way of achieving this, perhaps with a managed switch instead of unmanaged? Cheers

  Read the article

• Multiple Screen - Keyboard Sharing

  - by nhbdesign

  I run a small architectural firm with several drafters employed, I'm currently setting up a new office space and one of the things on top of my list is a figuring out a way to keep tabs on my drafters work and being able to collaborate in real time. Here's the challenge, they sit in a separate large cubicle room and I'm on the other end of the hallway, the way it is now; every time they’ve got some question on how to proceed on a certain design, they would come all the way to my office, I'd open their file (in read only) give some ideas, save-as new file, they go back copy paste... in short, nonsense. What I've been thinking of is to setup a hardwired solution that should enable me to have an extra monitor on my desktop which is hardwired (through KVM or something) to each of my employees workstations serving as a secondary display, so that I can watch live what they do, interact with them just as if they would have an extra keyboard and monitor in my office, except; I don’t want to have on my desk a separate monitor for each employee.. so I'd want them to be tiled on a single large screen, watching all screens alive, and whenever they ask me (or I just decide..) to step in, I just click on any tile and hurray, I'm in, editing and saving in real time on their workstation. I also want to reserve the option when I want to, to just use that monitor as just an extra screen for my workstation. Is something like that possible in 2013? P.S. I know of TeamViewer and similar internet/software based stuff, but I'm specifically looking for something solid hardwired and maintenance free, and also something that would allow to watch without my employees getting notified every time I do so (I’m not a tough boss though...).

  Read the article

• Adding a 2008 server to a 2003 Domain with DNS devolution?

  - by mvdwege

  I'm running into a problem adding a 2008 server to our existing 2003 domain, and as I am not a Windows admin, I'm not getting the problem here. Some reading around on Technet seems to indicate that DNS devolution is the issue. Here's the setup: DNS for the entire company is hosted on a Unix server running Bind, including the service records for the Windows domain. Our toplevel is company.local, and functional domains are in subdomains, such as mgt.company.local (our management servers). Our Windows servers live mostly in office.company.local, but some of them live in .mgt.company.local and .customers.company.local. The 2003 servers all succesfully authenticate against company.local as the Windows domain. Their position in the infrastructure is set by setting the primary DNS suffix under the network settings and the computer name dialog. Trying to do the same with a brand new 2008 install throws an error though: "Changing the Primary Domain DNS name of this computer to office.company.local failed [...] The specified server cannot perform the requested operation" I tried googling, but the closest I came was the Technet article on DNS Devolution, and I can't make heads nor tails on how to apply that to my case. Addendum 2012-10-23: The problem is not joining the domain, that works, the problem is that it joins with the wrong name, as .company.local, instead of .office.company.local. So far everything works, but I'm rather afraid to run production like this, because sooner or later something is going to complain about the AD name not matching DNS.

  Read the article

• phablet-flash aborting while installing Ubuntu Touch on Nexus 4

  - by Till B

  I have a Nexus 4 with Android 4.3 installed and I want to flash it to Ubuntu Touch. My system is Ubuntu 12.04, running inside a virtual machine on Mac OS 10.5.8. To use the VM, I opened an NAT bridge and forwarded port 5037 for adb, I can see the Nexus with adb and e.g. use the adb shell into it. USB ports are also forwarded to the VM. I follow these instructions to the letter. My bootloader is unlocked, just as it was described in the instructions. Now I encounter different issues, when executing sudo phablet-flash ubuntu-system --no-backup. On the first run, it got stuck in this state: INFO:phablet-flash:Decompressing partitions/recovery.img from /home/till/Downloads/phablet-flash/imageupdates/pool/device-5ba3031cb0d6fc624848266edba781e3e821b6e1e8dd21105725f0ab26077d0a.tar.xz INFO:phablet-flash:Restarting device... wait INFO:phablet-flash:Restarting device... wait complete INFO:phablet-flash:Booting /tmp/tmpMSN8bm/partitions/recovery.img < waiting for device > downloading 'boot.img'... OKAY [ 1.772s] booting... OKAY [ 0.005s] finished. total time: 1.779s INFO:phablet-flash:Waiting for recovery image to boot The following happened: around the line "INFO:phablet-flash: Restarting...", it rebooted into the bootloader. The bootloader shows only for two seconds, then the screen goes off and the phone stays off. But I do notice, that the screen is not off - it is just black, but the background light is on. If I wait long enough, phablet-flash aborts with ERROR:phablet-flash:Wait for recovery expired On the second try, I wanted to manually start the bootloader and choose "Recovery mode". Pressing "volume down+power" at first did nothing. Releasing the buttons and then pressing them again brought me into the bootloder. After choosing "Recovery mode", phablet-flash continued and after a while aborted with the following output: INFO:phablet-flash:Wait for recovery image to boot complete INFO:phablet-flash:Clearing /data and /cache INFO:phablet-flash:Pushing /home/till/Downloads/phablet-flash/imageupdates/pool/ubuntu-2b5345658b58e55207c4a4e7b6b3d8cd4f3d9a3187d2448fc9020c884234bac0.tar.xz to /cache/recovery/ failed to copy '/home/till/Downloads/phablet-flash/imageupdates/pool/ubuntu-2b5345658b58e55207c4a4e7b6b3d8cd4f3d9a3187d2448fc9020c884234bac0.tar.xz' to '/cache/recovery/': Permission denied ERROR:phablet-flash:Command 'adb push /home/till/Downloads/phablet-flash/imageupdates/pool/ubuntu-2b5345658b58e55207c4a4e7b6b3d8cd4f3d9a3187d2448fc9020c884234bac0.tar.xz /cache/recovery/' returned non-zero exit status 1 Removing directory /tmp/tmpDnbz6N Removing directory /tmp/tmpth4L6w What can I do to properly flash my phone with Ubuntu Touch? I noticed that adb does not show the phone in recovery mode: Typing adb devices, when the Nexus 4 is in recovery mode, shows the serial number and the state device, where it should show recovery. Should the phone be rooted? This is not mentioned in the instructions.

  Read the article

• Find More Streaming TV Online with Clicker.tv

  - by DigitalGeekery

  Looking for a way to access more of your favorite TV Shows and other online entertainment? Today we’ll take a look at Clicker.tv which offers an awesome way to find tons of TV programs and movies. Clicker.tv Clicker.tv is an HTML5 web application that indexes both free and premium content from sources like Hulu, Netflix, Amazon, iTunes, and more. Some movies or episodes, such as those from Netflix and Amazon.com’s Video on Demand, will require viewers to have a membership, or pay a fee to access content. There is also a Clicker.tv app for Boxee.   Navigation Navigating in Clicker.tv is rather easy with your keyboard. Directional Keys: navigate up, down, left, and right. Enter: make a selection Backspace: return to previous screen Escape: return to the Clicker.tv home screen. Note: You can also navigate through Clicker.tv with your PC remote. Recommended Browsers Firefox 3.6 + Safari 4.0 + Internet Explorer 8 + Google Chrome Note: You’ll need the latest version of Flash installed to play the majority of content. Earlier versions of the above browsers may work, but for full keyboard functionality, stick with the recommendations. Using Clicker.tv The first time you go to Clicker.tv, (link below) you’ll be met with a welcome screen and some helpful hints. Click Enter when finished.   The Home screen feature Headliners, Trending Shows, and Trending Episodes. You can scroll through the different options and category links along the left side.   The Search link pulls up an onscreen keyboard so you can enter search terms with a remote as well as a keyboard. Type in your search terms and matching items are displayed on the screen.   You can also browse by a wide variety of categories. Select TV to browse only available TV programs. Or, browse only Movies in the movie category. There are also links for Web content and Music.   Creating an Account You can access all Clicker.tv content without an account, but a Clicker account allows users to create playlists and subscribe to shows and have them automatically added to their playlist. You’ll need to go to Clicker.com and create an account. You’ll find the link at the upper right of the page. Enter a username, password and email address. There also an option to link with Facebook, or you can simply Skip this step.   Go to Clicker.tv and sign in. You can manually type in your credentials or use the onscreen keyboard with your remote.   Settings If you’d prefer not to display content from premium sites or Netflix, you can remove them through the Settings. Toggle Amazon, iTunes and Netflix on or off.   Watching Episodes To watch an episode, select the image to begin playing from the default source, or select one of the other options. You can see in the example below that you can choose to watch the episode from Fox, Hulu, or Amazon Video on Demand.   Your episode will then launch and begin playing from your chosen source. If you choose a premium content source such as iTunes or Amazon’s VOD, you’ll be taken to the Amazon’s website or iTunes and prompted to purchase the content.   Playlists Once you’ve created an account and signed in, you can begin adding Shows to your playlist. Choose a series and select Add to Playlist.   You’ll see in the example below that Family Guy has been Added and the number 142 is shown next to the playlist icon to indicate that 142 episodes has been added to your playlist. Underneath the listings for each episode in your playlist you can mark as Watched, or Remove individual episodes.   You can also view the playlist or make any changes from the Clicker.com website. Click on “Playlist” on the top right of the Clicker.com site to access your playlists. You can select individual episodes from your playlists, remove them, or mark them as watched or unwatched. Clicker.TV and Boxee Boxee offers a Clicker.TV app that features a limited amount of the Clicker.TV content. You’ll find Clicker.TV located in the Boxee Apps Library. Select the Clicker App and then choose Start. From the Clicker App interface you can search or browse for available content. Select an episode you’d like to view… Then select play in the pop up window. You can also add it to your Boxee queue, share it, or add a shortcut, just as you can from other Boxee apps. When you click play your episode will launch and begin playing in Boxee. Conclusion Clicker.TV is currently still in Beta and has some limitations. Typical remotes won’t work completely in all external websites. So, you’ll still need a keyboard to be able to perform some operations such as switching to full screen mode. The Boxee app offers a more fully remote friendly environment, but unfortunately lacks a good portion of the Clicker.tv content. As with many content sites, availability of certain programming may be limited by your geographic location. Want to add Clicker.TV functionality to Windows Media Center? You can do so through the Boxee Integration for Windows 7 Media Center plug-in. Clicker.tv Clicker.com Similar Articles Productive Geek Tips Share Digital Media With Other Computers on a Home Network with Windows 7Stream Music and Video Over the Internet with Windows Media Player 12Listen to Online Radio with AntennaEnable Media Streaming in Windows Home Server to Windows Media PlayerNorton Internet Security 2010 [Review] TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Nice Websites To Watch TV Shows Online 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos

  Read the article

• Unable to set background image using python (2.7.3), bash and gnome3

  - by malon

  #!/usr/bin/env python import os bashCommand = "gsettings set org.gnome.desktop.background picture-uri file:///home/malon/autowallpaperchanger/" + pic_name print bashCommand os.system(bashCommand) Print result: gsettings set org.gnome.desktop.background picture-uri file:///home/malon/autowallpaperchanger/wallpaper-1252048.jpg Copying and pasting the print result into a terminal makes the change successfully, so the command is correct, but os.system isn't processing the request correctly for some reason. In the full script (posted below), I use os.system for a different reason immediately before (wget) and that works fine. Thank you! Full script: http://pastebin.com/R90GTmBZ

  Read the article

• How to compile 'stygmorgan-0.29'?

  - by iwan

  I am trying to compile stygmorgan-0.29.tar.bz2 and got these messages: stygmorganui.cxx:7:28: fatal error: stygmicon128.xpm: No such file or directory compilation terminated. make[2]: *** [stygmorganui.o] Error 1 make[2]: Leaving directory `/home/papa/Downloads/stygmorgan-0.29/src' make[1]: *** [all] Error 2 make[1]: Leaving directory `/home/papa/Downloads/stygmorgan-0.29/src' make: *** [all-recursive] Error 1 papa@papa-G31-M7-TE:~/Downloads/stygmorgan-0.29$

  Read the article

• get the path of moved directory/file (source path and destination path)

  - by Ghanshyam Rathod

  When one directory is moved to other destination path, then i want to log the entry of original source path and entry of the path where it moved. any command is already available ? or any other way of doing this task? Ex: D1 = /home/user/Documents/test D2 = /home/user/Documents/Data/test when i moved D1 directory to the destination path to D2 directory then i want to log, like "test" directory is moved from D1 to D2 path Thanks

  Read the article

• Including Amazon affiliate link to Amazon homepage

  - by zpesk

  I want a link on my Web site that sends the user to the Amazon homepage, but includes my affiliate code so that any subsequent purchases get credited to my account. I have been browsing through the Amazon Associates portal and there only seems to be a way to link to a specific product. I found this link on daringfireball.net: http://www.amazon.com/exec/obidos/redirect?tag=daringfirebal-20&path=subst/home/home.html If I replace his affiliate code (daringfirebal-20) with mine, will this work? is this documented anywhere?

  Read the article

• Unity quick launch icon opens another program icon on program start

  - by Patrick

  I prepared a custom .desktop file for my chromium browser that loads a different user profile. When ever i click the icon now it open the browser, but also uses a new icon on the launcher bar (not locked to the launcher). Is there any way to tell the program to keep connected to the first icon? [Desktop Entry] Type=Application Name=Second Browser Exec=chromium-browser --user-data-dir="/home/patrick/bin/chrome-profiles/second" TryExec=chromium-browser Icon=/home/patrick/.local/share/applications/icons/browser.png MimeType=text/html;

  Read the article

• Installation problem: What does"Add this path and evaluate require" mean?

  - by PENG TENG

  I'm installing a software from github:OPEN-VRP It is said that : ~$ git clone git://github.com/mck-/Open-VRP.git Add this path and evaluate require: (push "/path/to/Open-VRP/" asdf:*central-registry*) (require 'open-vrp) (in-package 'open-vrp) What does "Add this path and evaluate require:" mean? I have followed the instruction and the termianl said peng@peng-ThinkPad-SL410:~/??/VRP$ push "/home/peng/??/VRP/Open-VRP" asdf:*central-registry* push: getaddrinfo(/home/peng/??/VRP/Open-VRP): Name or service not known

  Read the article

• KMenu & shell script

  - by allenskd

  I'm trying to make a very small shell script with a simple command and add it up to the KMenu. Well, thing is that once it launches the shell script, it closes it fast and I want to leave it open because the shell script attempts to create run a web application using a framework. I tried with this first #!/bin/bash play run /home/david/Projects/ZS then I tried with this #!/bin/bash konsole -e play run /home/david/Projects/ZSBlackboard In terminal, it runs perfectly, but in launcher.. not so much Any solution or suggestion is appreciated, thanks

  Read the article

• Help me solve my problem with NPR Media Player

  - by Calcipher

  First of, let me apologize for this getting a bit technical. Several weeks ago, I found that while using NPR's media player (e.g. click on 'Listen to the Show' - this is what I've been using as a test) the stream would suddenly halt after a minute or three. I could not get the stream to restart without reloading the page. Now, I assumed this was an issue with NPR's player and Linux (or just a bug in their stuff in general) so I began to dig, the following is what I have tried to date (please note, the tldr; option is to skip to the latest thing as I think I know what is causing the problem). Note: All testing has been done, for consistency purposes, on a clean install of Chromium with no pluggins running. My machine is Ubuntu 10.10x64. First thing I always try, I disabled all firewall stuff on the system (UFW, default deny all, allow ssh). No change, firewall back up for all additional tests unless otherwise noted. In any case, UFW is stateful, so connections it started on a non-specified on different ports will continue to work. I deleted my ~/.macromeda and ~/.adobe folders, restarted (just to be sure) and tried. Program still froze. I decided the problem might be with my install of flash, so I purged the version I had (and the home folders again). I installed the x64 version of flash from a PPA. This had no effect. I decided that the problem might be with the version of flash, so I purged the x64 version and installed the standard x32 version that comes with Ubuntu. No luck. Back to the x64 version for consistency, I decided to set up a 64-bit mini 'clone' of my system in VirtualBox. I was able to run the media player with no problem. I rsynced (in archive mode) my home directory from my real machine to the virtual machine (with bridged networking, so it was fully visible on the network). I also used a few tricks to install ALL of the same software (and repositories) from the real machine to the virtual machine. I was still able to listen to the player. I decided that the problem was with my install (after all, it had gone through two major version upgrades). As I have /home/ on a separate partition it was easy to reinstall and use the same trick from #6 to have my system up and running again within about an hour. I continue to have issues with the NPR Media Player. By this point the weekend had come. At work, I use a wired connection while at home I use a wireless connection. For some reason I forgot that I was having problems and used the NPR Media Player over the weekend. Low and behold it worked just fine at home on wireless (note: for various reasons, I could not test this on wired at home). Following from #6, I decided that the problem was either something with the network at work or still something with my account. As the latter was easier to test, I created a new account on my system and used that at work. The Media Player worked. At a loss, I decided to watch the traffic with tshark (the text based brother of wireshark) - X's to protect the innocent, I am the XXX.24.200.XXX: sudo tshark -i eth0 -p -t a -R "ip.addr == XXX.24.200.XXX && ip.addr == XXX.166.98.XXX" As you would expect, there were tons and tons of packets, but each and every time the player froze, this is what I got 08:42:20.679200 XXX.166.98.XXX - XXX.24.200.XXX TCP macromedia-fcs 56371 [PSH, ACK] Seq=817686 Ack=6 Win=65535 Len=1448 TSV=495713325 TSER=396467 08:42:20.718602 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=396475 TSER=495713325 08:42:21.050183 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495713362 TSER=396475 08:42:21.050221 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=396508 TSER=495713362 08:42:21.680548 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495713425 TSER=396508 08:42:21.680605 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=396571 TSER=495713425 08:42:22.910354 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495713548 TSER=396571 08:42:22.910400 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=396694 TSER=495713548 08:42:25.340458 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495713791 TSER=396694 08:42:25.340517 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=396937 TSER=495713791 08:42:30.170698 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495714274 TSER=396937 08:42:30.170746 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=397420 TSER=495714274 08:42:39.801738 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495715237 TSER=397420 08:42:39.801784 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=398383 TSER=495715237 08:42:59.032648 XXX.166.98.XXX - XXX.24.200.XXX TCP [TCP ZeroWindowProbe] macromedia-fcs 56371 [ACK] Seq=819134 Ack=6 Win=65535 Len=1 TSV=495717160 TSER=398383 08:42:59.032696 XXX.24.200.XXX - XXX.166.98.XXX TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] 56371 macromedia-fcs [ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=400306 TSER=495717160 08:43:00.267721 XXX.24.200.XXX - XXX.166.98.XXX TCP 56371 macromedia-fcs [FIN, ACK] Seq=6 Ack=819134 Win=0 Len=0 TSV=400430 TSER=495717160 08:43:00.267827 XXX.24.200.XXX - XXX.166.98.XXX TCP 56371 macromedia-fcs [RST, ACK] Seq=7 Ack=819134 Win=65535 Len=0 TSV=400430 TSER=495717160 So, as you can see, my machine is sending out a ZeroWindow packet (which I think means some buffer or another filled up) which causes the Media Player to halt (unfortunately, terminally - no controls on it really do anything anymore). Any ideas, at all, what would cause this? Why only on eth0 under my main account?

  Read the article

• Built-in network card not working?

  - by Zeeshan

  Hi, I am new to Ubuntu. I have installed Ubuntu 9.04(Jaunty). After installation I found that network card is not wokring. And id doest not list in "System Preferenes Network Connections" So , i got another card from my friend and try to search on internat about my problem but still cant find solution. Some commands output is here which may be help to solve problem root@mzeeshan-desktop:/home/mzeeshan# uname -r 2.6.28-11-generic root@mzeeshan-desktop:/home/mzeeshan# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:02:44:4a:45:12 inet addr:192.168.5.37 Bcast:192.168.5.255 Mask:255.255.255.0 inet6 addr: fe80::202:44ff:fe4a:4512/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3774 errors:0 dropped:0 overruns:0 frame:0 TX packets:3611 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4307045 (4.3 MB) TX bytes:583067 (583.0 KB) Interrupt:22 Base address:0x1000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) pan0 Link encap:Ethernet HWaddr 5e:25:17:a1:18:ac BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@mzeeshan-desktop:/home/mzeeshan# lspci 00:00.0 Host bridge: Intel Corporation Device 0069 (rev 12) 00:01.0 PCI bridge: Intel Corporation Auburndale/Havendale PCI Express x16 Root Port (rev 12) 00:19.0 Ethernet controller: Intel Corporation Device 10f0 (rev 05) 00:1a.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 1 (rev 05) 00:1c.4 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 5 (rev 05) 00:1c.6 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 7 (rev 05) 00:1c.7 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 8 (rev 05) 00:1d.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Ibex Peak LPC Interface Controller (rev 05) 00:1f.2 IDE interface: Intel Corporation Ibex Peak 4 port SATA IDE Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Ibex Peak SMBus Controller (rev 05) 00:1f.5 IDE interface: Intel Corporation Ibex Peak 2 port SATA IDE Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation GeForce 8400 GS (rev a1) 06:00.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) 06:00.1 Input device controller: Creative Labs SB Live! Game Port (rev 07) 06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 06:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) root@mzeeshan-desktop:/home/mzeeshan# Motherboard is Intel DP55WG. I don't know what to do next. Any help will be greatly appreciated.. Thanks

  Read the article

• How to restore .bashrc

  - by Miranda Webb

  Terminal shows this bash: /home/atlas/.bashrc: line 73: syntax error near unexpected token `[' bash: /home/atlas/.bashrc: line 73: `if [ -x /usr/bin/dircolors ] ; then ' I've tried to fix it using "cp /ect/skel/.bashrc ~/" And I get this "cp: cannot stat `/ect/skel/.bashrc': No such file or directory" I'm unsure of why this is doing this and how to fix it. I had previously been in the bashrc file messing around and apparently I've messed something up. All I want to do is restore the bashrc file to factory settings.

  Read the article

• A Brother MFC 7840w Printer Is A Good Companion To Any Desktop Computer

  Whether you run a small home based business or the kids just do their homework on it, a home computer needs a good printer attached to it. The Brother MFC 7840W printer not only produces high quality... [Author: Ben Pate - Computers and Internet - March 25, 2010]

  Read the article

• openssl/rand.h header file not found

  - by Arun Reddy Kandoor

  I have installed libssl-dev package but that did not install the include files. How do I get the openssl include files? Appreciate your help. Checking for program g++ or c++ : /usr/bin/g++ Checking for program cpp : /usr/bin/cpp Checking for program ar : /usr/bin/ar Checking for program ranlib : /usr/bin/ranlib Checking for g++ : ok Checking for node path : ok /usr/bin/node Checking for node prefix : ok /usr Checking for header openssl/rand.h : not found /home/arun/Documents/webserver/node_modules/bcrypt/wscript:30: error: the configuration failed (see '/home/arun/Documents/webserver/node_modules/bcrypt/build/config.log') npm ERR! error installing [email protected] npm ERR! [email protected] preinstall: `node-waf clean || (exit 0); node-waf configure build` npm ERR! `sh "-c" "node-waf clean || (exit 0); node-waf configure build"` failed with 1 npm ERR! npm ERR! Failed at the [email protected] preinstall script. npm ERR! This is most likely a problem with the bcrypt package, npm ERR! not with npm itself. npm ERR! Tell the author that this fails on your system: npm ERR! node-waf clean || (exit 0); node-waf configure build npm ERR! You can get their info via: npm ERR! npm owner ls bcrypt npm ERR! There is likely additional logging output above. npm ERR! npm ERR! System Linux 3.8.0-32-generic npm ERR! command "node" "/usr/bin/npm" "install" npm ERR! cwd /home/arun/Documents/webserver npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! code ELIFECYCLE npm ERR! message [email protected] preinstall: `node-waf clean || (exit 0); node-waf configure build` npm ERR! message `sh "-c" "node-waf clean || (exit 0); node-waf configure build"` failed with 1 npm ERR! errno {} npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /home/arun/Documents/webserver/npm-debug.log npm not ok

  Read the article

• Fix Nautilus URIs in a Python script

  - by Pablo

  I have a very basic Python script I wrote mostly for learning purposes. It opens a terminal in the current folder. However, I can't get it to work in folders with accented characters in the URI (e.g.: /home/pablo/Vídeos or /home/pablo/Área de Trabalho), because it looks like Nautilus URIs are encoded to those %{number} values. Is there a way to convert these URIs to normalized URIs without having to translate every possible accented value by hand? Thanks in advance!

  Read the article

< Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >