Search Results

Search found 7776 results on 312 pages for 'configure in'.

Page 175/312 | < Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >

• Why doesn't my computer work at full speed?

  - by kubilas

  My motherboard is a Gigabyte GA-8I915PL-G with an Intel Pentium 4 630 3,0 GHz which doesn't run at it's default speed. It's currently at FSB 800, CPU Host 200 and CPU 3000 MHz; but sometimes it runs at FSB 533, CPU Host 133 and CPU 2025 MHz. Sometimes it's even at FSB 75 and CPU 1128 MHz. When I configure the default settings in Easy Tune then my computer doesn't work. Sometimes I need to clear the CMOS so I can set the default settings in the BIOS, but that doesn't always help. I've updated the BIOS, what else can I do to fix this problem?

  Read the article

• How to change resolution in Ubuntu 10.04, where xvinfo is showing no adapters present?

  - by YumYum

  I am trying to maximize my resolution where I have Resolution: 800x600 (4:3) and Refresh rate: 61Hz I tried the following, but it did not work: $ xvinfo X-Video Extension version 2.2 screen #0 no adaptors present $ cvt 1920 1080 # 1920x1080 59.96 Hz (CVT 2.07M9) hsync: 67.16 kHz; pclk: 173.00 MHz Modeline "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync $ xrandr --newmode clever_name 173.00 1920 2048 2248 2576 1080 1083 1088 1120 $ xrandr -q Screen 0: minimum 640 x 480, current 800 x 600, maximum 800 x 600 default connected 800x600+0+0 0mm x 0mm 800x600 61.0* 640x480 60.0 clever_name (0x11d) 173.0MHz h: width 1920 start 2048 end 2248 total 2576 skew 0 clock 67.2KHz v: height 1080 start 1083 end 1088 total 1120 clock 60.0Hz $ xrandr --addmode default clever_name $ xrandr --output default --mode clever_name xrandr: Configure crtc 0 failed

  Read the article

• Is there anyway I can secure my connection when I try to log in to my router remotely?

  - by HardwareMuch

  I'm trying to configure my desktop to be accessed remotely. Here's what I've done so far: enabled wake on lan / remote wake up on all interfaces. I'm using logmein as my remote desktop application. setup DDNS so that I can log in to my router. When I try to remotely log in to my router it says that it is not encrypted there anyone can see my log in information. What can I do to make this a more secure setup? Any other suggestions or different methods will be greatly appreciated.

  Read the article

• What is the default value for Empty Temporary Internet Files when browser is closed in IE8?

  - by schellack

  We have four different machines that all have "Empty Temporary Internet Files when browser is closed" set to true (checked) in IE8's Internet Options (located under the Security section in the Advanced tab). No one remembers checking that checkbox to turn on the setting. What is the default value supposed to be? I'm specifically interested in Windows 7 and Windows XP. I have run rsop.msc on one of the corporate machines—3 of the 4 are members of a corporate network/domain—and see this under User Configuration, which makes the current scenario seem even stranger: The Local Group Policy Editor (gpedit.msc) also shows the Configure Delete Browsing History on exit setting to be Not configured (under Computer ConfigurationAdministrative TemplatesWindows ComponentsInternet ExplorerDelete Browsing History).

  Read the article

• How can I reduce the CPU usage of Offline Files?

  - by Diego

  Whenever I have the Offline Files service running, there is a constant 25% CPU usage on svchost.exe (this is a quad core, so that means it's using up one core). This, in turn, triples the power consumption and keeps the machine hot... I do have several GB synchronized (music collection), but they are not changing at all, in either side. Am I misusing this feature? Is there anything I can configure to keep it down when there's nothing to do? Or should I forget about it and synchronize big folders manually?

  Read the article

• Windows 7 Home Premium - Unable to View Chinese Characters Properly

  - by David

  Is there a proper and permanent fix that will restore the display of Chinese Characters on a Windows 7 Home Premium Laptop computer? This problem has been occurring frequently now and a simple reboot no longer does the trick. The square boxes viewed on many applications and websites has been constantly bothering me and I wish to fix it asap. I have done a lot of research on it but have not been successful. Many responses were to install the language packs for Windows 7 Ultimate Users which apparently is not my case or to configure the "Region and Language" settings of the Control Panel, changing the system locale. Does anyone have any suggestions? All would be appreciated!

  Read the article

• Cisco Aironet 1200 Series AP Configuration

  - by nonterrorist

  I am attempting to configure a new CISCO Aironet 1200 Series Access Point to have a fixed IP. I have been searching online and I have come to the conclusion that the default IP address of this device is 10.0.0.1. These are the steps I have taken: My machine is plugged directly into the Ethernet port (not the Console port) of the AP. My Ethernet adapter is set to 10.0.0.2. I have reset the AP by holding the Mode button while powering up the device. The issue remains that I can not access 10.0.0.1 through the web, nor can I ping that address.

  Read the article

• Remote desktop from internet to windows 7 box via linksys router

  - by larryq

  Hi everyone, I have a linksys wrt54g router and a windows 7 box at home I'd like to be able to remote desktop into from work. Would it be possible for someone to point me in the right direction on what I need to configure to get this working, both on the router and on the win 7 box? I'm sure there are a lot of little steps involved. Ideally I'd like to set it up so that only my work IP address can get through to the win 7 machine. Thanks very much for any pointers and links!

  Read the article

• Reserve one http slot for /server-status?

  - by Stefan Lasiewski

  I have an Apache server which is hanging for some reason. When I normally want to check on the load of an Apache server, I tend to use mod_status via the URL at http://webserver1.example.org/server-status or from the commandline like service httpd fullstatus. However today, the Server is refusing all new connections. Some mysterious problem is causing connections to stall, which means that number of connections fills up all available connections (e.g. The number of connects exceeds the MaxClients setting), and therefore neither http://webserver1.example.org/server-status nor service httpd fullstatus can return anything. Is it possible to configure Apache to reserve one or two slots for the mod_status pages?

  Read the article

• vncviewer connection refused (61)

  - by coure2011

  I have a root access to VPS (centos 6). I have installed VNCServer using this guide line http://tournasdimitrios1.wordpress.com/2011/02/02/how-to-setup-vnc-server-on-centos-5-x-fedora-11/ Everything goes perfectly and server is running via termina. Now I am trying to connect to that server via vncviewer (mac os). but its giving me error Connection refused (61) I am providing only the IP address of the VPS, maybe I also needed port address? How to configure port on vncserver? or its something else?

  Read the article

• Raid on ICH9R chip set

  - by user500982

  Hi Im looking at buyign this MB: http://www.supermicro.com/products/motherboard/ATOM/ICH9/X7SPE-HF-D525.cfm Im wondering though if the chipset will support the raid configuration I need. Im looking to configure the following arrays: raid array 1: 2 2TB Disks in Raid 0 raid array 2: 2 2TB Disks in Raid 0 raid array 3 (not actualy an array): 1 300GB Disk not in raid, to be used for OS and boot. So in total there would be 5 drives and the board supports 6. so im good when it comes to connections. However I have herd some chip sets only support one raid array (volume). so either all drives are individual, or are in the array. I must have 2 sperate raid arrays independent of each other, and a 5th drive not in any array. Anybody know if this setup will work? Thanks, -Stewart

  Read the article

• Help on using mod_rewrite to serve I18N static site

  - by Guandalino

  My static site www.example.com is translated in different languages and files are organized in this hierarchy: / /de index.html seite-1.html /en index.html page-1.html /it index.html pagina-1.html The root contains no files, just one subdirectory for each language the site is translated in, while subdirectories contain pages translated (both content and file name are) in the language corresponding to subdirectory name, de, en, it, etc. The question is: how to configure mod_rewrite so that when a client visits www.example.com it is taken to the correct version of the site, falling back to english version if the required locale is not supported (i.e. Accept-Language header doesn't exist or specifies a language for which the site is not available, e.g. fr)? Thanks for any pointer, I'm here to provide further details or feedback! Best regards

  Read the article

• How to issue machine certificates to Android devices trying to connect to L2TP VPN (L2TP/IPsec with Certificate)?

  - by John Hendrix

  I are trying to find a way to connect Android devices to our VPN box running Windows Sever 2008. We manage to configure a couple Android devices to connect via PPTP. However, I would like to be able to connect using L2TP/IPSec with certificates instead. I've managed to export and apply the Enterprise CA's certificate on the Android phone, but are totally lost on how to issue a machine certificate to the Android phone. Is it even possible? If so, what are steps I should take to issue the machine certificate and enable the Android phone to connect via L2TP/IPsec with certificates? Thank you for your help!

  Read the article

• Volume display for laptop missing after driver update

  - by Cyclone

  I have a Dell Inspiron 1520, and I just updated my audio drivers to be able to use Stereo Mix. It's a SigmaTel audio driver. Prior to the update, whenever I used the hardware buttons to update volume or mute/unmute speakers, it would always have a nice display like this one: But, for volume instead of screen brightness. The hardware buttons still work fortunately, but the volume display is gone. Is there a place I can configure this setting and re-enable it? The speaker icon in task tray was also disabled with the update, but I re-enabled that from the Control Panel. Is this simply gone with the driver update? Thanks for the help!

  Read the article

• Red Hat 5.4 slow processing

  - by yucefrizk

  I'm running Red Hat Linux 5.4 on HP DL580 server with 16 processors and 64 GB of RAM. I'm connecting to the server remotely through SSH. after entering the password, it takes time to return the command line, if I click ctrl+c during this time, I'll have the command line prompt but not the correct bash prompt (I have to run bash to pass to my correct prompt). I tried to install Apache on the server, ./configure took 4 hours to finish instead of 1 or two minutes, Oracle installation same behavior. Server Disks are mirrored using RAID controller. any idea what could be the reason of this slowness?

  Read the article

• How to limit my CPU power programmatically on Windows 7?

  - by Ivan

  Whenever I run a CPU-heavy activity (like compressing a big set of files into an archive for example) my CPU switches to its full throttle (maximum frequency) and shuts down of overheat in less than a minute. Instead, I would like it to keep slowed-down slightly to do the task a bit slower but be able to reach the finish. At the same time I don't want to dim my screen brightness or adjust anything else what standard Windows power-saving system does. So how do I actually set a cap to limit my CPU power? The CPU is Core 2 Duo T7250, the OS is Windows 7 32-bit, there seem to be no BIOS settings or jumpers available to configure the frequencies.

  Read the article

• Setting up Gitosis, where to create the repos?

  - by ReynierPM

  I'm trying to setup Gitosis on CentOS 6.2 but have some doubts/problems about it. I read this docs here, here and here but it's unclear to me where to configure where repositories are created. My server has a partition /data where I create a directory and called /gitrepos. I want all the repos created under that directory. By default if I run the command: gitosis-init < /home/reynierpm/reynierpm.pub I get this Initialized empty Git repository in /root/repositories/gitosis-admin.git/ Reinitialized existing Git repository in /root/repositories/gitosis-admin.git/ And I want this repos created under /data/gitrepos, any help? Thanks in advance

  Read the article

• Is it secure to store the cert/key on a private AMI?

  - by Phillip Oldham

  Are there any major security implications to bundling a private AMI which contains the private key/certificate & environment variables? For resiliency I'm creating an EC2 image which should be able to boot and configure itself without any intervention. After boot it will attempt to: Attach & mount specific EBS volume(s) Associate a specific Elastic IP Start issuing backups of the EBS volume(s) to S3 However, to do this it will need the private key/pem files and will need certain environment variables to be available on start-up. Since this is a private AMI I'm wondering if it will be "safe" to store these variables/files directly in the image so that I don't need to specify any user-data information and can therefore start a new instance remotely (from my iPhone, if needed) should the instance be terminated for any reason.

  Read the article

• Sendmail Alias for Nonlocal Email Account

  - by Mark Roddy

  I admin a server which is running a number of web applications for a software dev team (source control, bug tracking, etc). The server has sendmail running solely as a transport to the departmental email server over which I have no control. We have someone who is still in the department but no longer on the dev team so I need to configure the transport agent to redirect all outgoing email (which would be coming from these applications) to the person that has taken their place. I added an entry in /etc/aliases like such: [email protected]: [email protected] But when I run /etc/init.d/sendmail newaliases I get the following error: /etc/mail/aliases: line 32: [email protected]... cannot alias non-local names So clearly I'm doing something I shouldn't. Is there a way to get aliases to work with non-local names or alternatively is their a way to accomplish my goal of redirecting outgoing mail for this user to another one? Technical Specs if the matter: Ubuntu 6.06 sendmail 8.13 (ubuntu provided package)

  Read the article

• How to set up my network/bridging using Apple Airport equipment?

  - by John

  I'd like to set up my network like this, and I want to make sure it's possible using the hardware I have. I think it should be... I've got my cable modem in one room. I want to plug it into an Apple Airport Express and create my wireless my wireless network here. The airport express will do the NAT and DHCP. By my TV there are a few things to be networked (Xbox and Tivo). I have an airport extreme here. I'd like to have the airport extreme join the wireless network and share the connection to the ethernet ports. Can anyone provide some assistance on the best way to configure to do this? Thanks!

  Read the article

• Authentication issues setting up iRedMail on Debian

  - by Sergio Rinaudo

  I'm setting up an exchange server using iRedMail. Following the official iRedMail installation guide (http://www.iredmail.org/install_iredmail_on_debian.html) and the Digital Ocean guide (https://www.digitalocean.com/community/articles/how-to-install-iredmail-on-ubuntu-12-04-x64) I was able to install iRedMail without any problems, so I have all the services up and running. I can configure domains and emails using iRedAdmin BUT I have problem both sending and receiving email, what I get from Roundcube is 'Authentication error' when trying to send an email. Also I can't receive anything. I also tried to connect to the mx server using telnet, it connects, but after the STARTTLS command, when I start to write "MAIL FROM:" the connection is lost. Something in the configuration is not working (at the moment I have the configuration written by the iRedMail installation) but I do not know where, I hope someone can enlight me! Thank you

  Read the article

• MySQL Cluster Failover doesn't work

  - by Lukasz

  I have two servers, where First server 10.100.15.150: 1. one mgm server 2. one ndbd 3. one mysql api Second server 10.100.15.160: 1. one ndbd 2. one mysql api When i start all 'parts' of cluster it looks : Cluster Configuration [ndbd(NDB)] 2 node(s) id=21 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17, Nodegroup: 0) id=22 @10.100.15.160 (mysql-5.1.56 ndb-7.1.17, Nodegroup: 0, Master) [ndb_mgmd(MGM)] 1 node(s) id=3 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17) [mysqld(API)] 2 node(s) id=11 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17) id=12 @10.100.15.160 (mysql-5.1.56 ndb-7.1.17) When i shutdown first machine - 10.100.15.150, on second the nbdb process also has been shutdown so i cannot use this data node and cluster fail ... How i must configure this cluster to get FailOver working ? Thx

  Read the article

• Yum install packages to an alternate directory, without chroot?

  - by Stefan Lasiewski

  I would like to use the Foswiki yum repository to install Foswiki (296 packages). The default installation path is /var/lib/, but I want to install it to an alternate location at /opt/www/. In the future, I still want to use yum to check for and apply updates to the packages. Is it possible to use yum to install packages to an location which is different then the default location provided by RPMs? Does Yum provide anything similar to ./configure --prefix=/usr/local/ or rpm --install --prefix=/opt/local? Yum provides the --installroot option, but that appears to primarily for chroot environments.

  Read the article

• SSH issues: Read from socket failed: Connection reset by peer

  - by nitins

  I compiled OpenSSH_6.6p1 on one of our server. I am able login via SSH to the upgraded server. But I am not able to connect to other servers running OpenSSH_6.6p1 or OpenSSH_5.8 from this. While connecting I am getting an error as below. Read from socket failed: Connection reset by peer On the destination server in the logs, I am seeing it as below. sshd: fatal: Read from socket failed: Connection reset by peer [preauth] I tried specifying the cipher_spec [ ssh -c aes128-ctr destination-server ] as mentioned in here and was able to connect. How can configure ssh to use the cipher by default? Why is the cipher required here?

  Read the article

• Disable RAID Controller

  - by B.Mr.W.

  I have some decent HP Proliants server that come with "HP Smart Array P410i Controller" enabled, I am using these boxes to set up a Hadoop cluster and I know, RAID is for sure a no-no for Hadoop since the application itself will take care of data redundancy and extra intelligence provided by RAID won't be helpful and might turn down the performance. I tried to disable the devices at the BIOS and the box cannot even access the disk afterwards. So I am assuming the controller is sitting between disks and mother board, and we have to turn it on and configure it to "level0" or something like that. I am wondering what should I do to "disable" the RAID functionality so it will fit into the Hadoop environment.

  Read the article

< Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >