Search Results

Search found 5373 results on 215 pages for 'wireless bridge'.

Page 176/215 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• Can't mount time capsule via wi-fi.

  - by Grnmntn

  I have an Apple time capsule, and have been able to back up to it without a problem for the past few months. However, today I found I cannot connect to the time capsule from Finder, though it appears there, when I click "connect as...", it takes a few seconds and then reports connect failed, "the server may not exist or it is not operational at this time. Check the server name or IP address and your network connection and try again". When I check Time Machine, it says the last backup failed because "the backup volume could not be mounted". The strange part is, the time capsule is also my router, and I am able to use the time capsule as a wireless access point without a problem. Any ideas?

  Read the article

• windows 7 issues with local domain name

  - by Phill

  Until recently my operating system was XP where for the purpose of development and testing of php and zen cart I set up xampp that included apache http server and mercury mail server I also made changes to C:\Windows\System32\drivers\etc\hosts as follows: 127.0.0.1 www.zen.com # For browser access 127.0.0.1 mail.mercury.com # For email access 127.0.0.1 mercury.com # For mercury mail server This allowed the use of www.zen.com in the address bar of my browser rather than 'localhost' and mail.mercury.com to access email via thunderbird. All was well. Then I installed windows7, I made all the mods and again everything appeared to run as expected.Then I turned off my wireless modem causing all working local connections to fail. Localhost in the address bar still works but not www.zen.com and thunderbird 'cannot find mail.mercury.com' Is there some way to overcome what ever is causing this.

  Read the article

• Windows 7 USB power lose after a few seconds / minutes

  - by Stefan Dunn

  My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

  Read the article

• VNC failure on Xen

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Networking - intermittent, slow speeds

  - by jack

  Hi all I'm a novice when it comes to networking. I live in a large two storey building that used to be a school and we have an internet connection with BT (british telecoms provider), the connection speed is 12Mb.. Basically our connection is slow and very intermittent and I was wondering if anybody here could provide some help or ideas. There are about 11 people in the building who could be online at any time. We have a router on the ground floor which is bog standard supplied by BT. To provide Broadband access to the 1st and 2nd floors, we used an old switch that the school left, we have a cable running from the router on the first floor to the switch which connects to a wireless router which is configured as a bridge on the 2nd floor supplying broadband access to the 1st and 2nd floors. Additionally we have 3 computers that are connected via the switch through the ethernet sockets left by the school on the ground floor. The router we use on the 2nd floor came in a pack of 2 and cost about £15 (bought by another person). Sometimes the connection is perfectly fine, i.e. early hours of the morning or when everybody is out, we have rang BT who say that the connection cannot cope with the numbers of people online, plus I'm not sure whether each person is streaming etc. Can anybody offer any advice?

  Read the article

• Setting Up an IP Camera in ZoneMinder from Ubuntu

  - by Chris S

  I recently bought a TV-IP312W wireless IP camera. I've completed the basic setup on the camera itself, and confirmed I can stream video using the utility CamViewer. Now I'm trying to access the camera from ZoneMinder, so I can setup monitors and alerts. However, I'm finding the documentation a bit laking. Following the tutorial and a forum post, I've install ZoneMinder, and can access the web interface, but I'm getting stuck at the "Check that your Camera Works!" section. I can add a monitor, but after I add the configuration: Source Type: FFMPEG Source Path: http://192.168.1.105/cgi/mjpg/mjpeg.cgi?.mjpeg all I get is a broken image. What am I doing wrong?

  Read the article

• What's constitute an entry on the IPTables and how to find out which client it is originated from

  - by cbd

  I have a Billion BiPac 7700N Modem/Router/Access Point and I connect another router (TP-Link TL-WR1043ND) in wan-bypass mode to extend the wireless coverage. Lately, I noticed that the connection through TP-Link has been dropping out quite regularly. Having read some posts on the Internet, I checked system log on 7700N and found that there are many "nf_conntract: expectation table full" errors, which I suppose the iptables are full. My questions: What does constitute an entry on the iptable? Is it a client or a connection (which means one client can have multiple connections) How could I find out where are those connections originated from? Note: Many reported that the issue is usually related to having torrents running but I don't have any torrents running. Thank you.

  Read the article

• Enabling the log app on the WDTV

  - by Ariel Popovsky

  Just flashed the last WDXLTV firmware on my WDTV and it's working fine. I tried to config a Wifi USB adapter but couldn't get it to work. Dropped the log-saver.app.bin on the root of the stick but didn't find any log files after booting. What I'm doing is turning on the WDTV with the stick inserted (the stick is formatted with FAT32). Tried with the wireless-mod.app.bin required files and without any other file than the log saver. I can't get a log file anyway. All I want right now is to get the log file so I can debug the WI FI adapter.

  Read the article

• How to install Windows 7 From Network?

  - by George

  Hello SuperUser My question is that is it possible to install Windows 7 (Current RTM Version) on a computer without using removable media like DVD or USB. First thing that comes to my mind is network but i dont have experience of doing Fresh Install of Windows 7 via Network. How to install Windows 7 via network without any removable media? P.S. I know some may think that doing so, is just a waste of time and it's easier to do it with removable media, but in current situation the target PC neather has CD/DVD Drive nor supports booting from USB. And in addition to that, Target computer is connected to Network via Wireless Network (Dunno if it will make any problem with installation).

  Read the article

• Virtual machines interconnection inside Proxmox 2.1 Cluster

  - by Anton

  We have 3 physical servers (each with 1 NIC) in different datacentres, all of them are interconnected by openvpn bridged private network (10.x.x.x). Inside this network we have fully functional 3 nodes Proxmox 2.1 cluster. So, actually question is: Is there any "proper" way to make "global" local network (172.16.x.x) for all VMs inside cluster, so even if we move VM from one node to other we could reach it by static IP regardless of it's physical location? BTW, we can't add dedicated NIC to each server. Thanks in advance. EDIT: I have tried to make a separate openvpn bridge for 172.16.x.x, now I have at each server two interfaces: SRV1: openvpnbr1 - 172.16.13.1 vmbr0 - 172.16.1.1 SRV2: openvpnbr1 - 172.16.13.2 vmbr0 - 172.16.2.1 But now there is no connection between those ifaces: SRV1: ping 172.16.13.2 From 172.16.1.1 icmp_seq=2 Destination Host Unreachable SRV2: ping 172.16.13.1 From 172.16.2.1 icmp_seq=2 Destination Host Unreachable If I shut down vmbr0 interfaces, so there is connection between servers over openvpn, but vmbr0 is used by Proxmox... Where I am wrong?

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• VNC on Xen failure

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Splitting Ethernet cable

  - by Nathan

  I am looking for the best way to network my small business. I have an office where my router/modem are located, and then 2 more computers in another room. I can route Ethernet to this room with about 75 ft of cabling, and I would like to do this because my computers on Ethernet are getting 3x the speed as computers on wireless. Is there any way I can use just one Ethernet cable to span the 75 feet, and then maybe 2 smaller ones to go to the two computers from there? If there's a simple way to do this, maybe with a connector that would be ideal, as opposed to buying over 150 ft of cabling. Thanks!

  Read the article

• Print server does not show up on router's attached devices

  - by AshTee

  Recently I bought a new more powerful wireless N router, DLink DIR 628. So I removed all connections from the previous router (Netgear WGT624) and connected them as they should be to the DLInk router. Everything works fine except for the print server. I have Hawking print server connected to HP Laserjet 6P parallel port printer. It works well with the Netgear router. But when I connect it to the DLInk router, it does not even show up in the LAN computers list. I am not sure what is going on. There is a utility called PSAdmin that can talk to the Hawking print server if I switch to Netgear router. With that utility, I can get the assigned IP address to the print server. But when switching to DLink router, even the PSAdmin fails to find the print server. I have been trying various things for last couple of days in vein. Please help.

  Read the article

• Advantages / disadvantages of having DynDNS access on a computer vs the router

  - by Margaret

  I have a shiny new toy, a Cisco Wireless-N Gigabit Security Router with VPN (WRVS4400N). While looking through the instruction manual, I discovered that it had support for DynDNS built-in. We've currently got the DynDNS client running on one of the servers (that people SSH to, as documented in this question); but the reason for the router update is to move away from SSH to VPN. To that end, is there any difference in behaviour/functionality/maintainability to run it off the computer, as opposed to the router? Thus far, DynDNS has more or less a set-and-forget setup, but since the feature was there, I wanted to know if it was a better location for the process...

  Read the article

• Pros/cons to turning off cable modem

  - by Jay

  A little off the wall perhaps, but ... I have a cable modem and a router for a wireless home network. Is it a good or a bad idea to turn it off at night and during the day when we're all at work or school? Or should I leave it on 24/7. I was thinking that leaving it on constantly makes me more vulnerable to hackers, not to mention wasting electricity. (Though I'd guess the amount of electricity used by a cable modem and a router is probably pretty trivial. Still, every little bit helps.) When I have turned it off and turned it on again, it takes several minutes for it to go through its little dialog with the cable company and get me connected to the Internet again, which is annoying but not a big deal. Anyone know any good reasons one way or the other?

  Read the article

• Using radvd to advertise ipv6 over VPN connection using DD-wrt

  - by Sean Madden

  My ultimate goal is to allow VPN users to have access to my internal IPv6 network from across the intertubes. I've got a linksys WRT54GSv2 running DD-WRTv24SP1 and have configured the little guy as specified here http://www.dd-wrt.com/wiki/index.php/IPv6 and it works wonderfully over the br0 interface (LAN/WLAN bridge). Here's the issue though, when I add an additional interface to the radvd config file on the router (specifically ppp0, for the VPN traffic), radvd refuses to start. The kicker is that on DDWRT, it doesn't give an error message, it just fails outright. Any suggestions on where to proceed from here? /jffs/radvd.conf: interface br0 { AdvSendAdvert on; prefix 0:0:0:1::/64 { AdvOnLink on; AdvAutonomous on; }; }; interface ppp0 { AdvSendAdvert on; prefix 0:0:0:1::/64 { AdvOnLink on; AdvAutonomous on; }; }; The documentation I've found for radvd is slim, but if anyone has a decent idea on how to proceed I'd love to hear it.

  Read the article

• "custom" routers for VPN - useful or waste of money?

  - by Andrew Heath

  I use VPN in China and my current service contract expires soon so I was checking what sort of plans are out there now. I found that Witopia offers a "Cloak Box", what appears to be a Linksys wireless router with allegedly hacked/custom firmware to support VPN. Aside from allowing multiple computers to share one VPN connection, is there anything else at work here to justify that price when most new routers are $100 or less these days? Or is this something targeted towards the cd-rom cupholder crowd? And yes, I've contacted them, but haven't heard back yet... EDIT I've heard back from the company - here are the details if anyone else is interested: the router is a Linksys WRT54GL running TomatoVPN custom firmware the hardware waranty is one (1) year, from Linksys/Cisco the VPN is hard-set, so any device connected to the router MUST use the VPN (Witopia blocks torrents) I've decided it's not for me, but hopefully this information will prove useful to others.

  Read the article

• Howto print from dumb terminals with local print server and remote hosted RDP

  - by Matt

  We have essentially a remote office with about 5 dumb terminals. The terminals are connecting to our office directly over a wireless link. What I want to do is connect all their printers onto a print server. But since the remote office is not actually allowed to see our LAN (since they are actually another company) we don't want a full on open VPN tunnel set up. Naturally the RDP traffic passes through a firewall. Is there an easy way to set up the RDP server so that it can see a print server on a remote LAN?

  Read the article

• After installing Windows Phone 8 SDK, Connectify doesn't work

  - by Pratyush Nalam

  Today I installed Windows Phone 8 SDK from the official site. After installing and a couple of restarts (it restarted the PC to enable Hyper-V), I opened Connectify. I use Connectify Hotspot to connect my iPod to the internet as I have an ethernet connection and no wireless router. The problem is that now, Connectify doesn't show WiFi in Share Over. The attached screenshot shows this. Previously, before I installed the SDK, it would show Ethernet and Wi-Fi. I would select WiFi and share my internet. Now, this is completely screwed. EDIT: I found out that the Microsoft Virtual Wi-Fi Miniport Driver has got disabled and I am not able to enable it again. Please advise. Please advise on what to do Hardware: Windows 8 Pro with Media Center, Apple MacBook Pro 9,1 15 inch Mid-2012 (non retina)

  Read the article

• Strange behavior in networking between 64bit and 32bit

  - by Rob

  I'm having a strange behavior about my network setup. I have 2 laptops, one (Lenovo) with Windows 7 Professional 64-bit and another (Acer) with Windows 7 Ultimate 32-bit and a wireless router. I'm connecting these 2 using the router but with a strange behavior. I can ping both machines, as well as the router, but when i try to access their shared folders (\\computer_name\shared_folder) the connection starts to fail and I need to reboot both machines to get it working again. But this only happens sometimes, sometimes it works.

  Read the article

• Sharing files between 2 different routers

  - by Chris

  I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

  Read the article

• No keyboard works

  - by Adrian Mester

  I'm trying to troubleshoot a problem a friend is having. Her keyboard suddenly stopped working. She had a wireless keyboard/mouse combo and the mouse still worked. She tried with a different usb keyboard, and it still didn't work. She tried with a PS/2 keyboard and it didn't work. She's running Windows 7, but the keyboard also doesn't work during boot-up. I've got no idea what could possibly be the problem. Any suggestions?

  Read the article

• Users not getting ip when connected through wifi,but wired connection getting ip in ddwrt router

  - by Kevin Parker

  I am having DD-WRT v24-sp2(05/08/11) running on Asus RT n 13 u B1 router,with dhcp on. But users not able to connect through wifi...its showing obtaining ip address and disconnects there after. Wired Devices are getting ip address and able to access internet.Wifi was working till yesterday,but all of a sudden it stopped working. on the ddwrt controlpanelsystem information under Wireless Clients mac address of clients that are trying to connect are appearing but soon it disappears. but no such issue with wired clients. Can any one please help me in fixing this..

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >