Search Results

Search found 4909 results on 197 pages for 'board games'.

Page 178/197 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• Using a 64bit Linux kernel, can't see more than 4GB of RAM in /proc/meminfo

  - by Chris Huang-Leaver

  I'm running my new computer which has 8GB of RAM installed, which is visable from BIOS page, does not show in /proc/meminfo uname -a Linux localhost 3.0.6-gentoo #2 SMP PREEMPT Sat Nov 19 10:45:22 GMT-- x86_64 AMD Phenom(tm) II X4 955 Processor AuthenticAMD GNU/Linux The result of /proc/meminfo is as follows: (thans Andrey) MemTotal: 4021348 kB MemFree: 1440280 kB Buffers: 23696 kB Cached: 1710828 kB SwapCached: 4956 kB Active: 1389904 kB Inactive: 841364 kB Active(anon): 1337812 kB Inactive(anon): 714060 kB Active(file): 52092 kB Inactive(file): 127304 kB Unevictable: 32 kB Mlocked: 32 kB SwapTotal: 8388604 kB SwapFree: 8047900 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 492732 kB Mapped: 47528 kB Shmem: 1555120 kB Slab: 267724 kB SReclaimable: 177464 kB SUnreclaim: 90260 kB KernelStack: 1176 kB PageTables: 12148 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 10399276 kB Committed_AS: 3293896 kB VmallocTotal: 34359738367 kB VmallocUsed: 317008 kB VmallocChunk: 34359398908 kB AnonHugePages: 120832 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 23552 kB DirectMap2M: 3088384 kB DirectMap1G: 1048576 kB I have tried using mem=8G as a kernel boot parameter, I read a post about setting HIGHMEM64G to yes, before realising that only applies to 32bit kernels. Trying dmindecode -t memory SMBIOS 2.7 present. Handle 0x0026, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 32 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0028, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM0 Bank Locator: BANK0 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer0 Serial Number: SerNum0 Asset Tag: AssetTagNum0 Part Number: Array1_PartNumber0 Rank: Unknown Handle 0x002A, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM1 Bank Locator: BANK1 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer1 Serial Number: SerNum1 Asset Tag: AssetTagNum1 Part Number: Array1_PartNumber1 Rank: Unknown Handle 0x002C, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM2 Bank Locator: BANK2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer2 Serial Number: SerNum2 Asset Tag: AssetTagNum2 Part Number: Array1_PartNumber2 Rank: Unknown Handle 0x002E, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM3 Bank Locator: BANK3 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: Array1_PartNumber3 Rank: Unknown

  Read the article

• HT Link Sync Error after Ubuntu 10.04 LTS Installation

  - by marklab

  Update 1 I just assembled an exact replica of this server, and successfully installed Ubuntu 10.04 LTS in a RAID10 configuration. The success was confirmed by a login to the initial account. There must be a hardware component that is faulty. Since the error mentions HT, which I believe to be Hyper Threading, I will start with the CPUs. Please indicate if this error is more strongly associated with any other piece of hardware. Or make a recommendation of another approach that would be good for this issue. Issue I was attempting to install Ubuntu 10.04 LTS on this system with the board RAID10 configured. However, the installation failed at the partitioning stage by rebooting the system. Upon reboot, there is an error report after POST listing the following: Node0: NB WatchDog Timer Error Node1: HT Link Sync Error Node2: HT Link Sync Error ... Node7: HT Link Sync Error Press F1 to continue/resume. After pressing F1 the system will boot from the Ubuntu 10.04 LTS installation disc. However, it will fail at the same stage, and go through the same process from there. Hardware CPU: AMD OPTERON X12 6172 G34 2.1G 18MB Motherboard: Supermicro H8QG6-F HDD: WD Caviar Green 2TB 5.4K RPM Troubleshooting I disabled RAID10 on the system, and installed the Ubuntu on a single drive. It installed successfully. I then went back to a RAID10 setup and attempted to install on the system again, and was able to make it through the partitioning stage. However, upon reboot, the system reported: Error: file not found, and then booted me into the Grub Rescue console. I feel I have aggravated the problem at this point because when I attempted to install from the boot disc again, the system reboots upon hitting enter to even start the installation process. It does the same thing when trying to boot from an Ubuntu 11 disc. I have not been able to find any information on this HT Link Sync Error, which I feel may have started the problems I am experiencing now with the installation of the OS. I am also aware that Ubuntu is said not to be supported by the motherboard according to Supermicro's site. However, since I was able to install it successfully on a single drive, I do not believe it is incompatible. I would like to know a reason for why it's failing to install on/off.

  Read the article

• Can you set up a gaming LAN using OpenVPN installed in a VMware guest OS and be playing the game on the host OS?

  - by Coder

  I would like to setup a gaming VPN. Ie. I have some games that work over LAN and would like to play them with people that are not on my LAN. I know I can do this with OpenVPN. My ultimate goal would be to run OpenVPN portably on my host OS and not even need any virtualization. As such i don't want to install it on my host, but i'm fine with running it portably. I'm even fine with temporarily adding registry keys, and then running a .reg file to remove these entries once i'm done. To this effect i have installed OpenVPN on a virtual machine and diffed the registry. I then manually (using a .reg file) added all the keys that seem important on my host OS and copied the installation folder of OpenVPN onto my host machine. Then i try to run openVPN GUI 1.0.3 as a test and it says "Error opening registy for reading (HKLM\SOFTWARE\OpenVPN). OpenVPN is probably not installed". I verified that that key is indeed in the registry with all subkeys and it looks correct. I have tried running the GUI as an administrator and in compatibility mode with no success. I am running Windows 7. If this fails then i would be happy with installing OpenVPN on a virtual machine in VMWare but they key is that i will be running the game installed on my host machine. The first question for this option is if this is even possible. The second is, that I can't get the VM to have internet access if I use bridging but i can if i use NAT. Is it possible to do this game VPN setup with VMWare guest OS running using NAT? Summary of questions: -Is it possible to run openVPN portably and if so what did i miss above? -If it's not possible to run it portably, then can setup a gaming LAN by installing OpenVPN in a guest OS with NAT and how can i do this? -If the above is not possible then can i install OpenVPN in a guest using bridging and if so how can i set this up with a Windows 7 host and Windows XP guest as currently i can't get the guest to be able to access the internet in bridging mode, but it working in NAT mode. -In general is there any good documentation on setting up a gaming LAN with OpenVPN (i am using 2.1.4) as i have never set up a VPN of any sort before so any help would be much appreciated. Thanks!

  Read the article

• SMPS stops when I plug in a SATA drive?

  - by claws

  Hello, Part 1: my first question is all the 4 wire power connectors (intended for hardisks/dvd drives not mother board) are same. Right? I've been using all of them same and I had no problem for years. Yesterday I borrowed a SATA disk from my friend and connected it my computer using Sata Power adaptor (4 wire) and when I switched on the computer. There were fumes coming out of the connector. I immediately turned it off (in just one second). I tested the voltages in the 4 wire power connector of my SMPS: They were 5.3v & 12.2V. I couldn't measure the current. But my SMPTS label reads: DC Output: 3.3v (25A) +5v (32A) -5v (0.3A) +12V (17A) -12V (0.8A) And the SATA hardisk label reads Input: +5v (0.72A) +12V (0.52A) I'm shocked! I never noticed this. Does the "sata power adaptor" scale down the current to required? If it doesn't, I've been connecting same way for years. I never had any problem. This is the first time I'm encountering it. Part 2: I wanted to return the drive to my friend. He has two hard disks, SATA & PATA. Its the SATA that I borrowed. When he usually switches on. The CPU fan starts & then stops for a sec and starts again and continues working. That was the earlier situation. I don't know why it stops & starts? Well, Now when I connect this SATA disk and switch ON the computer. CPU fan starts (just for an instant, not even a 0.5 sec) and stops. It doesn't start again, I mean the power from SMPS has stopped. But if I disconnect this SATA disk. It works fine. What seems to be the problem? I've no idea about why there were fumes or why his SMPS starts & stops giving power? What is its relation with the SATA disk connection?

  Read the article

• Torque jobs does not enter "E" state (unless "qrun")

  - by Vi.

  Jobs I add to the queue stays there in "Queued" state without attempts to be executed (unless I manually qrun them) /var/spool/torque/server_logs say just 04/11/2011 12:43:27;0100;PBS_Server;Job;16.localhost;enqueuing into batch, state 1 hop 1 04/11/2011 12:43:27;0008;PBS_Server;Job;16.localhost;Job Queued at request of test@localhost, owner = test@localhost, job name = Qqq, queue = batch The job requires just 1 CPU on 1 node. # qmgr -c "list queue batch" Queue batch queue_type = Execution total_jobs = 0 state_count = Transit:0 Queued:0 Held:0 Waiting:0 Running:0 Exiting:0 max_running = 3 acl_host_enable = True acl_hosts = localhost resources_min.ncpus = 1 resources_min.nodect = 1 resources_default.ncpus = 1 resources_default.nodes = 1 resources_default.walltime = 00:00:10 mtime = Mon Apr 11 12:07:10 2011 resources_assigned.ncpus = 0 resources_assigned.nodect = 0 kill_delay = 3 enabled = True started = True I can't set resources_assigned to nonzero because of Cannot set attribute, read only or insufficient permission resources_assigned.ncpus. When I qrun some task, this goes to mom's log: 04/11/2011 21:27:48;0001; pbs_mom;Svr;pbs_mom;LOG_DEBUG::mom_checkpoint_job_has_checkpoint, FALSE 04/11/2011 21:27:48;0001; pbs_mom;Job;TMomFinalizeJob3;job 18.localhost started, pid = 28592 04/11/2011 21:27:48;0080; pbs_mom;Job;18.localhost;scan_for_terminated: job 18.localhost task 1 terminated, sid=28592 04/11/2011 21:27:48;0008; pbs_mom;Job;18.localhost;job was terminated 04/11/2011 21:27:48;0080; pbs_mom;Svr;preobit_reply;top of preobit_reply 04/11/2011 21:27:48;0080; pbs_mom;Svr;preobit_reply;DIS_reply_read/decode_DIS_replySvr worked, top of while loop 04/11/2011 21:27:48;0080; pbs_mom;Svr;preobit_reply;in while loop, no error from job stat 04/11/2011 21:27:48;0080; pbs_mom;Job;18.localhost;obit sent to server Scheduler log (/var/spool/torque/sched_logs/20110705): 07/05/2011 21:44:53;0002; pbs_sched;Svr;Log;Log opened 07/05/2011 21:44:53;0002; pbs_sched;Svr;TokenAct;Account file /var/spool/torque/sched_priv/accounting/20110705 opened 07/05/2011 21:44:53;0002; pbs_sched;Svr;main;/usr/sbin/pbs_sched startup pid 16234 qstat -f: Job Id: 26.localhost Job_Name = qwe Job_Owner = test@localhost job_state = Q queue = batch server = localhost Checkpoint = u ctime = Tue Jul 5 21:43:31 2011 Error_Path = localhost:/home/test/jscfi/default/0.738784810485275/qwe.e26 Hold_Types = n Join_Path = n Keep_Files = n Mail_Points = a mtime = Tue Jul 5 21:43:31 2011 Output_Path = localhost:/home/test/jscfi/default/0.738784810485275/qwe.o26 Priority = 0 qtime = Tue Jul 5 21:43:31 2011 Rerunable = True Resource_List.ncpus = 1 Resource_List.neednodes = 1:ppn=1 Resource_List.nodect = 1 Resource_List.nodes = 1:ppn=1 Resource_List.walltime = 00:01:00 substate = 10 Variable_List = PBS_O_HOME=/home/test,PBS_O_LANG=en_US.UTF-8, PBS_O_LOGNAME=test, PBS_O_PATH=/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/games, PBS_O_MAIL=/var/mail/test,PBS_O_SHELL=/bin/sh,PBS_SERVER=127.0.0.1, PBS_O_WORKDIR=/home/test/jscfi/default/0.738784810485275, PBS_O_QUEUE=batch,PBS_O_HOST=localhost euser = test egroup = test queue_rank = 1 queue_type = E etime = Tue Jul 5 21:43:31 2011 submit_args = run.pbs Walltime.Remaining = 6 fault_tolerant = False How to make it execute jobs automatically, without manual qrun?

  Read the article

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• Ubuntu 12.10 Clock is wrong

  - by mardavi

  I have an issue with Ubuntu Quantal, as it shows the wrong time. It is completely messy, the right time from time.is now is 09.43 and my clock shows 17.48. I am using ntp service and I already checked the timezone and it is correct. I also checked the hardware clock through sudo hwclock --showsudo dpkg-reconfigure tzdata and this is right too. I also tried sudo dpkg-reconfigure tzdata but with bad luck. What else can I try? As asked, here my /etc/ntp.conf # /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for help driftfile /var/lib/ntp/ntp.drift # Enable this if you want statistics to be logged. #statsdir /var/log/ntpstats/ statistics loopstats peerstats clockstats filegen loopstats file loopstats type day enable filegen peerstats file peerstats type day enable filegen clockstats file clockstats type day enable # Specify one or more NTP servers. # Use servers from the NTP Pool Project. Approved by Ubuntu Technical Board # on 2011-02-08 (LP: #104525). See http://www.pool.ntp.org/join.html for # more information. server 0.ubuntu.pool.ntp.org server 1.ubuntu.pool.ntp.org server 2.ubuntu.pool.ntp.org server 3.ubuntu.pool.ntp.org server time.nist.gov # Use Ubuntu's ntp server as a fallback. server ntp.ubuntu.com # Access control configuration; see /usr/share/doc/ntp-doc/html/accopt.html for # details. The web page <http://support.ntp.org/bin/view/Support/AccessRestrictions> # might also be helpful. # # Note that "restrict" applies to both servers and clients, so a configuration # that might be intended to block requests from certain clients could also end # up blocking replies from your own upstream servers. # By default, exchange time with everybody, but don't allow configuration. restrict -4 default kod notrap nomodify nopeer noquery restrict -6 default kod notrap nomodify nopeer noquery # Local users may interrogate the ntp server more closely. restrict 127.0.0.1 restrict ::1 # Clients from this (example!) subnet have unlimited access, but only if # cryptographically authenticated. #restrict 192.168.123.0 mask 255.255.255.0 notrust # If you want to provide time to your local subnet, change the next line. # (Again, the address is an example only.) #broadcast 192.168.123.255 # If you want to listen to time broadcasts on your local subnet, de-comment the # next lines. Please do this only if you trust everybody on the network! #disable auth #broadcastclient In addition, the ntp service was not running when I turned on my laptop today.

  Read the article

• HID USB Very Strange Problem...

  - by Lasanha

  I realy hope some one can help me here cause i search all over the web and nothing comes up.. I allways used PS/2 KB and Mouse and a USB KeyPad (Genius ErgoMedia 500 Gaming Explorer) to play some games, mmorpg, fps, you named, very good whit 11 keys whit possible macros etc etc... Now it comes the problem, i have a USB mouse that have 4 extra buttons, and i need more button, i love buttons.. Well, i plug in the USB mouse and disconectes de PS/2. Everything is ok until i toutch the mouse. If i do so, the ErgoMedia goes off, then on, then i mouse the mouse or press a button and all over again. Yesterday i went buying a new mouse that i liked, a USB mouse too (NPlay whit macros and all that stuff 3600dpi...) Hoping the problem was only whit the other mouse, but no.. It does the exact same thing, ErgoMedia keeps disconecting and conecting everytime i toutch the mouse. What i allready did: Update drivers of both mouses Update drivers of ErgoMedia (no specific drivers(Windows based)) Update drivers of MB Chipset (Actualy no, cause it was up to date allready) Trying other USB Ports (4 Ports back, 4 Ports Front and even 1 Port in 16 card slot device) Disable the "Allows Windows to shut down the energy bla bla" thing in Device Setings. Look up in the Device Setings only apear a problem on the ergomedia (Human interface Device) when i move the damm mouse.. Using Everest to read behavier, everything normal, exepts the disconecting thing, but no errors. Not a power suply, only the ErgoMedia and the mouse are in the USBs, and i allready disable the 16 card reader whit one usb slot to see.. Clean the IRQ registry. Look the entire internet for a fix solution. Help others problems wile looking for a fix for me (Im not a pro but not a completly stupid) Talking to you beggin you to help me as a last resorce... Machine: Acer M3641 Core2Quad 64x Based OS Vista 64b 4GbRAM HD Audio and Graphics I realy hope some one out there knows a fix for this, maybe it´s a simple thing, so simple that i´m to stupid to see that.. Sorry for my bad inglish but i write lot of erros even in my language. Any help will be very welcome. Tanks for ur concern and atention ^^

  Read the article

• The Koyal Group Info Mag News¦Charged building material could make the renewable grid a reality

  - by Chyler Tilton

  What if your cell phone didn’t come with a battery? Imagine, instead, if the material from which your phone was built was a battery. The promise of strong load-bearing materials that can also work as batteries represents something of a holy grail for engineers. And in a letter published online in Nano Letters last week, a team of researchers from Vanderbilt University describes what it says is a breakthrough in turning that dream into an electrocharged reality. The researchers etched nanopores into silicon layers, which were infused with a polyethylene oxide-ionic liquid composite and coated with an atomically thin layer of carbon. In doing so, they created small but strong supercapacitor battery systems, which stored electricity in a solid electrolyte, instead of using corrosive chemical liquids found in traditional batteries. These supercapacitors could store and release about 98 percent of the energy that was used to charge them, and they held onto their charges even as they were squashed and stretched at pressures up to 44 pounds per square inch. Small pieces of them were even strong enough to hang a laptop from—a big, fat Dell, no less. Although the supercapacitors resemble small charcoal wafers, they could theoretically be molded into just about any shape, including a cell phone’s casing or the chassis of a sedan. They could also be charged—and evacuated of their charge—in less time than is the case for traditional batteries. “We’ve demonstrated, for the first time, the simple proof-of-concept that this can be done,” says Cary Pint, an assistant professor in the university’s mechanical engineering department and one of the authors of the new paper. “Now we can extend this to all kinds of different materials systems to make practical composites with materials specifically tailored to a host of different types of applications. We see this as being just the tip of a very massive iceberg.” Pint says potential applications for such materials would go well beyond “neat tech gadgets,” eventually becoming a “transformational technology” in everything from rocket ships to sedans to home building materials. “These types of systems could range in size from electric powered aircraft all the way down to little tiny flying robots, where adding an extra on-board battery inhibits the potential capability of the system,” Pint says. And they could help the world shift to the intermittencies of renewable energy power grids, where powerful batteries are needed to help keep the lights on when the sun is down or when the wind is not blowing. “Using the materials that make up a home as the native platform for energy storage to complement intermittent resources could also open the door to improve the prospects for solar energy on the U.S. grid,” Pint says. “I personally believe that these types of multifunctional materials are critical to a sustainable electric grid system that integrates solar energy as a key power source.”

  Read the article

• Get 5.1 surround sound from computer through a VCR config?

  - by Wedding Nails

  I'm posting to see if my idea of this setup is right and can be done. I currently have the following "equipment": a JVC VCR -quite old-, which has built in surround sound (aka it has several speaker outputs, which I believe is 5.1 and are connected to several speakers that are in every corner of the room), a computer with SPDIF optical output and a new flat screen TV (with built in HDMI). I want the computer to take advantage of the VCR's surround system (all the speakers in the room) in order to play mainly music and video always with all the speakers (5.1) and with the maximum sound quality. Currently, the computer plays sound only through the front speaker (I connect one output to the on board pc audio input) and the quality is really bad. As a side note, the computer video runs with S-video (old school), and the picture quality as you would imagine, is really bad with the new big LCD screen. My main goals are: to upgrade the picture with a new video card which would support HDMI (my tv has HDMI). to buy a SPDIF optical cable, connect one end to the VCR SPDIF input and the other end to the PC output This is theoretically what I've researched so far, and I came out with several questions: in this case, with the SPDIF cable connected, and all the configurations done in windows allowing the 5.1, will I get every content I play "converted" or played through all of my speakers? (I read this forum post). I already know that in order for this setup to play from all the speakers, the content/audio source has to be 5.1. but my question is, if there is a way to play from all of the speakers no matter what type of content I'm playing (that's why I said conversion there) I already know that HDMI cables carry digital sound. Is there a way I can only use said HDMI cord to the tv, and get sound through the VCR? (I'm not too sure about this, I would have to disable the TVs speakers and use the VCR surround as default, but I have no clue wether this can be done or not). Update: The ultimate question is, do I really have to rely on "sound virtualization" technology to get sound from all the speakers, no matter what content I play? (do I require a newer sound card, like a creative soundblaster with said technology?) Thanks!

  Read the article

• Where to get laptop replacement parts?

  - by wai

  I am sure some of us have older laptops that still works but just one or two parts started not working very well. However, to send it back to the manufacturer for repair might not be worth the money (as some of them even charge consultation fees just to have it checked) as these old laptops are most probably well beyond warranty. Replacing these one or two parts could give your laptop a new lease of life. For example, I have a Dell Inspiron 640m which the fan recently failed. Everything else still works. I know enough to open up the laptop (after reading the service manual) and put it back together again, hence a replacement fan could save it. However, finding these parts turned out to be difficult. I guess I wouldn't be able to get it from Dell since I have been searching around the Dell forums and concluded if I were going to get Dell to at least talk to me, I would have to pay some money (since my warranty expired). I found this online:- http://www.parts-people.com/index.php?action=item&id=3725 However, as I don't live in the United States, shipping alone would cost me 3 times more than the part in question. In addition, if there's a problem, it would be difficult because I probably would have to mail the parts back (costing more money). One of my friend spilled water on her Macbook, she sent it back to Apple and they told her the cost of repairing it exceeds that of buying a new Macbook. They probably have to change everything except the LCD screen. I opened it up and found that most of the parts are still working, only the RAM had fried. Replaced it and it's working again. For some time before discovering only the RAM fried, I was toying with the idea of replacing the logic board myself but looks like I didn't have to. =) Now I know there's a site for Macbooks used replacement parts:- http://www.ifixit.com/ The question is, does anyone know where to get replacement parts at their own locality? It might benefit the community as a whole. Someone might know a local computer store that sells precisely just the things we needed (for now, I hope to find a shop that sells just the fan). If you own a laptop which you had an easy experience finding the replacement parts, do post that as well. PS: I wish laptop manufacturers have outlets where they sell these replacement parts (or at least let you place an order).

  Read the article

• How can I play my MP3 files through my stereo system?

  - by Joel Coehoorn

  Here's the situation. Like many others I have my entire CD collection ripped to my PC, along side other music I've acquired through iTunes or Amazon MP3. Also like many others the speakers at my PC are underpowered, and likely included in my monitor as an afterthought. This is fine for most use: system sounds, YouTube, etc. Even games sounds and music. But I'd like something a little better for when I really want to listen to music. And I have it; in the next room — barely 25 feet away as the crow flies — sits a nice 400 watts stereo system. The stereo supports MP3 CDs, so up to this point I've just kept a few CD-RW disks around to keep most of my collection available. But it's time to move on to something a little more sophisticated. What are my options for using the MP3 files available on my computer as an input for this stereo? Some notes: I want to be able to control what song the stereo is playing without having to go to the PC, including setting up and retrieving playlists. Ideally this should even be able to wake the PC from sleep mode to start playing. I primarily use Windows Media Player on the PC (which runs Windows Vista). However, the files themselves live on a server running Windows Server 2008, and so I could also install something on the server and run everything from there. The axillary input on the stereo is unfortunately limited to a 1/8 inch stereo mini-plug. I'm loath to run wires across two rooms, and I'm considering moving the stereo to the garage at some point. Therefore a wireless solution that can easily cover about 100 ft or so is preferred. I already have a Wi-Fi network ready, but it's secured so anything using Wi-Fi should make it easy to set up security. Bonus points for doing it in under $85 shipped at Amazon (I'm hoping to pay for this via $85 worth of Amazon gift cards). I know this a pretty tight budget, so just getting close is okay. Bonus points for something that remembers multiple profiles (keep my favorite songs separate from the wife's). Bonus points for a remote that can also replace my stereo remote, so I only need one device to control everything. I'm not holding my breath on this one given my price range, though. Bonus points if I can also use for Internet radio. Doing some research on my own as well. This looks like it'll do exactly what I want, but it lists at an outrageous $299: http://www.linksysbycisco.com/US/en/products/DMP100

  Read the article

• Gigabyte GA-970A-UD3 mobo won't boot from USB flash drive

  - by user38586

  I am trying to boot BAMT a Debian flavor via USB on a brand new Gigabyte GA-970A-UD3 motherboard. I tried various flash drive and various OS. I never had this problem with ASUS and MSI. The problem is from Gigabyte hardware. I found that my BIOS is very strict about MBR compatibility. Now I can boot in DOS mode. The flash drive need to be formated as a Win98 Startup disk using HP USB disk storage format tool. Unetbootin menu is booting from USB but won't install BAMT. If I use Windows or Linux diskimager the working MBR is deleted. I tried converting BAMT .img to .iso and it is not booting with Unetbootin. Is it possible to boot BAMT(Debian Linux) from a Win98 DOS command prompt? Maybe there is a way to burn the image and keep the working MBR? If the working MBR is deleted, the flash drive is not recognized at all by the BIOS. This is the info I found that got me booting for the first time in DOS: GB's BIOS will only boot USBs formatted to FAT-32, conforming to normal MBR bootloader. I've seen this before, and surmised that the 'stick-maker' was formatting in ReiserFile, or one of the EXT 'flavors', but no one ever followed up to confirm or deny... Also, if it's putting the bootloader into its own partition - won't work! In the BIOS, on the "Integrated Peripherals" page, the "USB Storage Function" item must be enabled (which should be the default) to allow USB booting... I've put a little work into a 'GB USB booting tutorial', and frankly, I'd just go ahead and finish it up for you, but I really don't want to reboot the several times it will take me to 'firm up' procedural details, and take the BIOS/boot pictures for the post - just noticed VAIL finally went 'public beta', so will be downloading for likely twenty-six hours or so There's likely enough there to test a 'raw DOS boot', just to see if your hardware (especially the USB stick itself) will do it... Some post later: Fixed. Here is a brief summary. Since my ubuntu live usb sticks (2gb kingston and 8gb sandisk sd/usb reader - fat32, created in ubuntu 10.04) would not boot this board even though they would boot my ga-ep45-ud3p, I decided to try bilbat's suggestion with the HP usb boot program. I created the win98 boot disk on the kingston 2gb stick without reformatting. It booted right up. Next, I used windows version of unetbootin to write the ubuntu live cd to the kingston disk. This fired right up and completed the install. Everything seems to be in good order now. Unfortunately I can boot in DOS mode but can't boot BAMT.

  Read the article

• dmidecode showing more ram slots than available?

  - by Jestep

  I have some failing RAM in a server and I ran dmidecode to figure out what tyoe of RAM I needed to replace it with. The server has 6 RAM slots, 4 of which are in use. When I run dmidecode this is what I get. dmidecode 2.10 SMBIOS 2.4 present. Handle 0x001F, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 00 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0020, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 01 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0021, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 02 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0022, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 03 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0023, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 10 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0024, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 11 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0025, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 12 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0026, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 13 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Does anyone know why it would show 8 slots, with 4 empty instead of 6 slots with 2 empty? Also, but my records and by other tools, the server has 16Gb and not 8Gb in it currently. grep MemTotal /proc/meminfo MemTotal: 16435808 kB The board is a Tyan S5372-LC, running CentOS 5.4 x64. Also, my error log is showing errors in bank 6. Is there any way to determine which slot bank 6 is in via: dmidecode?

  Read the article

• Skyrim: Heavy Performance Issues after a couple of location changes

  - by Derija

  Okay, I've tried different solutions: ENB Series, removing certain mods, checking my FPS Rate, monitoring my resources, .ini tweaks. It's all just fine, I don't see what I'm missing. A couple of days ago, I bought Skyrim. Before I bought the game, I admit I had a pirated copy because my girlfriend actually wanted to buy me the game as a present, then said she didn't have enough money. Sick of waiting, I decided to buy the game by myself. The ridiculous part is, it worked better cracked than it does now uncracked. As the title suggests, after entering and leaving houses a couple of times, my performance obviously drops extremely. My build is just fine, Intel i5 quad core processor, NVIDIA GTX 560 Ti from Gigabyte, actually stock-OC, but manually downclocked to usual settings using appropriate Gigabyte software. This fixed the CTD issues I had before with both Skyrim and BF3. I have 4GB RAM. A website about Game Tweaks suggested that my HDD may be too slow. A screenshot of a Windows Performance Index sample with the subscription "This is likely to cause issues" showed the HDD with a performance index of 5.9, the exact same mine has, so I was playing with the thought to purchase an SSD instead, load games onto it that really need it like Skyrim, and hope it'd do the trick. Unfortunately, SSDs are likewise expensive, compared to "normal" HDDs... I'm really getting desperate about it. My save is gone because the patches made it impossible to load saves of the unpatched version and I already saved more than 80 times despite being only level 8, just because every time I interact with a door leading me to another location I'm scared the game will drop again. I can't even play for 30 mins straight anymore, it's just no fun at all. I've researched for a couple of days before I decided to post my question here. Any help is appreciated, I don't want to regret having bought the game... Since it actually is the best game I've played possibly for ever. Sincerely. P.S.: I don't think it's necessary to say, but still, of course I'm playing on PC. P.P.S.: After monitoring both my PC resources including CPU usage and HDD usage as well as the GPU usage, I don't see any changes even after the said event. P.P.P.S.: Original question posted here where I've been advised to ask here.

  Read the article

• Run Flyff without elevating user to Admin or requiring Admin Password

  - by AnonJr

  Bottom Line: I need to set up one game on my little sister's laptop to run without requiring an admin password/account. Its the only game that seems to insist on it... so far. Detailed Version: I set up my 14-year-old sister as a regular user on her Windows 7 Home Premium laptop, and almost everything has been fine - until she found a new game (Flyff) that doesn't seem to want to run without an Admin Password (or being logged in as an Admin). For what should be obvious reasons, I'm not going to make her an Admin. or give her the Admin password (which she swears she'll only use to run this game... anyone else buying that? Bueller?) Also, the parents aren't admins on her laptop (they are on their own, but that's another discussion for another day) and I'm not going to set them up as one as I know from past experience that the 3rd time my sister asks them to put in their password, they'll just tell her what it is - at which point I might as well as have just set her up as an admin from the outset. This is a Win7 Home Premium (64-bit, but I doubt that makes a difference) laptop, so using GPEdit is out. I also tried an answer provided in a related (but less specific) question. The app has read/write permissions for its folder in Program Files (x86), yet that doesn't seem to make a difference. I have not yet dug through the registry as mentioned in another answer to the aforementioned question. Just to be thorough, I have checked the "Run as Admin" option on the shortcut's properties to no avail. Am I missing something? Addendum 2010-11-11: Re-Checked permissions as per Joel's answer, and it didn't make a difference. Followed Jane T's suggestion (and Aeo's second) and created a "Games" folder outside Program Files, installing the game there - and making sure regular users had all the permissions they would need. No joy. After the latter of the above two changes, it occurred to me that it may be a UAC issue, so for kicks I turned off UAC - still the damn message. Last item noted: could it be a result of the publisher not being specified/verified? I've been taking a closer look at the error message and it occurred to me that the missing/unverified publisher info could have been the problem all along... Correct me if I'm wrong, but if that's the case, that means there's nothing I can do short of giving her some sort of Admin privileges (i.e. elevating her account, or giving her the password to a separate Admin account) or giving Mom an Admin account.

  Read the article

• Win 8: Adding a boot volume to an MBR dynamic disk [NOT about changing to basic disks]

  - by Stilez

  (This is NOT aiming to convert to basic disk. In this question, the disk stays dynamic but becomes bootable) There doesn't seem to be a clear, well stated answer I can find, for the question "What are the criteria for Windows 8 to successfully boot from an MBR dynamic disk", or "how do I fix a dynamic MBR partition that's failing boot"? I've tried to educate myself but can't find crucial information to clear it all up. My existing HDD/SSD setup: DISK 0 ~ 60GB SSD/MBR/basic: (350MB recovery)(60GB windows 8 bootable) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISK 2 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISKS 3, 4, 5: (ignored for simplicity: 2xHDD RAID1 + caching SSD) I'm heavy duty on data crunching and virtualisation, just maxxed out 32GB RAM @ 2133 and moved to 4960X + 64GB. Disk 0 is a pure system disk of little value, and virtualisations runs off mirrored SSDs (Samsung 840 Pro 512 x 2) for double speed reading and so they snapshot in reasonable time. I'm using 4 SATA3 ports and the board only has two decent Intel ports (onboard Marvell are poorer quality). I'm wary of choosing between LSI, HighPoint and other 3rd party controllers as I'm unfamiliar with the maze of decent RAID cards (that's a whole other issue!). I want to cut down my SSD needs by moving the boot volume and caching volume to the 840 pros, giving a setup with 2 fewer SSDs: DISK 0 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB boot)(410GB mirrored data) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(30GB cache for the ICH10R mirror)(30GB temp)(410GB mirrored data) DISKS 2, 3: (2xHDD RAID1) Intel's RST allows this, Win 8 allows booting off a MBR/dynamic disk, and the two 60GB SSDs are hardly the fastest SSDs anyway, they'll get repurposed. Moving the caching volume is easy. Moving the boot volume has me stumped. The difficulty is, I'm hitting a wall of knowledge here. I have a UEFI Asus motherboard with an previous traditional MBR/basic boot disk, and I want it to boot from a disk and volume that's MBR/dynamic. The disk copy is physically ok (Partition Wizard Server will copy to dynamic volumes) but then hits a light blue 0xc000000e boot error. No real surprise, I expected to have some boot fixing, but had expected Windows to boot-fix it (all drivers exist), or the usual manual fixes to work. Specifically, I don't know enough, to know what's got to be manually checked and perhaps corrected for the disk to boot (legacy/uefi/bios, odd partitions, boot tables, disk IDs, hidden boot files, oh my!), or if I need to change any of this secure boot/UEFI/legacy stuff in the bios, convert a 512 SSD to basic and then back to dynamic when working, or if the issue is pure OS config using "diskpart", "bootsect" and "bootrec" from the Win8 DVD. The old system disk still boots but I don't know enough to figure what to fix, to make the system boot as I want. The answers probably aren't hard but the real issue is my confusion and missing information. Thanks for helping!

  Read the article

• Where to get laptop replacement parts?

  - by wai

  I am sure some of us have older laptops that still works but just one or two parts started not working very well. However, to send it back to the manufacturer for repair might not be worth the money (as some of them even charge consultation fees just to have it checked) as these old laptops are most probably well beyond warranty. Replacing these one or two parts could give your laptop a new lease of life. For example, I have a Dell Inspiron 640m which the fan recently failed. Everything else still works. I know enough to open up the laptop (after reading the service manual) and put it back together again, hence a replacement fan could save it. However, finding these parts turned out to be difficult. I guess I wouldn't be able to get it from Dell since I have been searching around the Dell forums and concluded if I were going to get Dell to at least talk to me, I would have to pay some money (since my warranty expired). I found this online:- http://www.parts-people.com/index.php?action=item&id=3725 However, as I don't live in the United States, shipping alone would cost me 3 times more than the part in question. In addition, if there's a problem, it would be difficult because I probably would have to mail the parts back (costing more money). One of my friend spilled water on her Macbook, she sent it back to Apple and they told her the cost of repairing it exceeds that of buying a new Macbook. They probably have to change everything except the LCD screen. I opened it up and found that most of the parts are still working, only the RAM had fried. Replaced it and it's working again. For some time before discovering only the RAM fried, I was toying with the idea of replacing the logic board myself but looks like I didn't have to. =) Now I know there's a site for Macbooks used replacement parts:- http://www.ifixit.com/ The question is, does anyone know where to get replacement parts at their own locality? It might benefit the community as a whole. Someone might know a local computer store that sells precisely just the things we needed (for now, I hope to find a shop that sells just the fan). If you own a laptop which you had an easy experience finding the replacement parts, do post that as well. PS: I wish laptop manufacturers have outlets where they sell these replacement parts (or at least let you place an order).

  Read the article

• External USB HD issues with a twist (works on Windows7 but not XP)

  - by Eruditass

  I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

  Read the article

• How could I let Skydrive desktop sync to MicroSD in Windows 8 tablet?

  - by peSHIr

  I have a Samsung Slate 7 tablet with (now) Windows 8 on it. This machine has a 64 Gb SSD and I have a 64 Gb MicroSD card in it. I also have a Skydrive on my main Microsoft ID that contains about 45 Gb of content. With Windows and some development stuff installed, my Skydrive will not fit on the main drive of the tablet. (Besides, my idea was to keep data on the memory card anyway, to make it easier to repave the machine without data loss if need be.) My problem should now be clear: I want to install the Skydrive desktop app to sync my Skydrive to the MicroSD card. This is not possible, as Skydrive does not allow syncing files to removable drives. I have tried a number of things already, but none of them worked: Use the mklink command line tool to create a directory link/junction from a folder name on SSD to a folder on the MicroSD and then try to install Skydrive sync to the SSD link folder. Skydrive however still recognizes this as something it does not want to sync onto. The various different filter drivers mentioned on Agnipulse (including the Hitachi one) that should make windows see some or all of the removable drives in the system as fixed drives do not seem work on (64-bit) Windows 8: they either can't be installed, do nothing and/or cause Windows 8 to go into Automatic Repair mode when rebooting. The Lexar BootIt app seems to be meant to flip the relevant bit in the on-board drive controller of supported USB pen drives, but I tried it anyway. Of course it did nothing to how the MicroSD card was seen. I have now run out of ideas, it seems, and I was wondering if anyone here has a solution to let Windows 8 see the MicroSD memory card in my tablet as a fixed drive instead of removable drive, or some other way of getting the Skydrive desktop to sync my Skydrive data to that MicroSD card. And to be complete: this is not a duplicate question of this or this as those ask about getting USB drives multiple partitions to work on Windows XP. This question is specific about getting desktop Skydrive to sync to MicroSD card in Windows 8, which seems to be a question I have not seen on superuser so far.

  Read the article

• How to upgrade a 1.4.3 TortoiseSVN-created repository to 1.6.x?

  - by SiegeX

  A few years ago, TortoiseSVN 1.4.3 was deployed to our software development team and we are now looking at upgrading the client to the latest 1.6.x version. I had hoped this upgrade would be transparent with the additional features and modifications being client-side. For the most part, this was true except for a very important feature -- merging. When I try to merge a feature branch back into truck I get a show-stopping "Merge tracking not supported error." Here are some facts worth noting: When the repo was first created (before I was on board), it was created via the TortoiseSVN client itself. We do not have a 'svn server daemon' per se, rather the repository folders/database resides on a share folder that is accessible from our workstation machines via file:///. This was actually an eye opener for me, I had always thought there was some SVN server daemon we were talking to. We do not have any access to the underlying machine hosting the SVN share other than the ability to read/write to the share itself. I don't even know what OS the machine is running on. This share server was chosen because its drives are backed up nightly by our IT group. In all honesty, we really don't need the merge tracking feature although it would be nice to have. For the time being it would be sufficient to be able to use a 1.6.x TortoiseSVN client on the 1.4.3 repository and have it merge (sans tracking) without error. So now the question becomes, how does one upgrade a client-created 1.4.3 repo to a 1.6.x compatible version without access to the underlying machine the repo resides on? I was hoping the TortoiseSVN client itself had the ability to do this but that does not appear to be the case. Will I be forced to copy the entire repo over to my local drive, run some svn commands to upgrade the repo locally then copy the repo back to the share point? If so, will doing this break any compatibility with the the 1.4.3 clients in case we cant upgrade them all at the same time? Thanks for the help.

  Read the article

• How to upgrade a 1.4.3 TortoiseSVN-created repository to 1.6.x?

  - by SiegeX

  A few years ago, TortoiseSVN 1.4.3 was deployed to our software development team and we are now looking at upgrading the client to the latest 1.6.x version. I had hoped this upgrade would be transparent with the additional features and modifications being client-side. For the most part, this was true except for a very important feature -- merging. When I try to merge a feature branch back into truck I get a show-stopping "Merge tracking not supported error." Here are some facts worth noting: When the repo was first created (before I was on board), it was created via the TortoiseSVN client itself. We do not have a 'svn server daemon' per se, rather the repository folders/database resides on a share folder that is accessible from our workstation machines via file:///. This was actually an eye opener for me, I had always thought there was some SVN server daemon we were talking to. We do not have any access to the underlying machine hosting the SVN share other than the ability to read/write to the share itself. I don't even know what OS the machine is running on. This share server was chosen because its drives are backed up nightly by our IT group. In all honesty, we really don't need the merge tracking feature although it would be nice to have. For the time being it would be sufficient to be able to use a 1.6.x TortoiseSVN client on the 1.4.3 repository and have it merge (sans tracking) without error. So now the question becomes, how does one upgrade a client-created 1.4.3 repo to a 1.6.x compatible version without access to the underlying machine the repo resides on? I was hoping the TortoiseSVN client itself had the ability to do this but that does not appear to be the case. Will I be forced to copy the entire repo over to my local drive, run some svn commands to upgrade the repo locally then copy the repo back to the share point? If so, will doing this break any compatibility with the the 1.4.3 clients in case we cant upgrade them all at the same time? Thanks for the help.

  Read the article

• Hard freeze on new computer

  - by mphair

  OCZ Gold 3x2GB 240-Pin DDR3 SDRAM PC312800 Palit NE5T240SFHD01 GeForce GT240 1GB 128-bit GDDR5 ASUS P7P55D-E LGA 1156 P55 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Intel Core i7-860 Lynnfield 2.8GHz 8MB L3 Cache LGA 1156 95W Quad-Core Processor SAMSUNG 22X Optical drive (DVD+-R/RW) CORSAIR CMPSU-620HX 620W ATX12V V2.2 Windows 7 Ultimate x64 Brand new system (got it from newegg two days ago) and it booted up and installed windows and ran for a day just fine. Yesterday, I boot it up in the afternoon and run various games at full graphics for most of the day. I turn on WoW and play for a few hours and it hard stalls. No numlock switching, no mouse feedback but nothing going wrong on the screen. No BSOD. I wait a bit to see if the stall is just a temporary one, but then force shutdown the computer. Upon reboot, everything seems fine, windows sees that it didn't shut down properly but I go into normal boot and restart WoW. I'm able to load it up and start running around when it freezes again. This time when I restart, it doesn't even get to BIOS. It starts (power goes on) and it just hangs with no output to the monitors. I shut it off and went to bed. This morning, I turned it on and went into BIOS setup. I'm not terribly experienced with messing with BIOS settings but I checked over them the best I could. Everything seems fine so I boot into windows and browse the internet for a bit looking for a solution, hard freeze within 10 minutes. I restart and go into BIOS and check the CPU temperature, 40c. I'm kinda stumped here. Some people say it might be a memory issue, but why would it take so long for it to come up? Could it have been slowly accessing one memory stick at a time and then it just got to a bad one and that's what is causing it to fail? It seems odd that I don't get a BSOD from a hardware failure. Having the screen just halt with no input or output change seems like a software thing to me. Any thoughts?

  Read the article

• Asus M4A79XTD-EVO / AMD Phenom II X4 965 Crashes / BSOD / Hangs / Restarts

  - by Tiby

  I'll try to be as concise as possible because I have a lot to say about my problem, but I'd rather say it when asked or when I feel it's necessary, just to make this initial reading clearer. For about a year and a half I have periods when my system has all the problems in the title (I'll use the word 'crash' for either one). I'll list some patterns and what I tried to do and what were the results, but the list is not exclusive: usually it crashes when a CPU-intensive operation is in progress, like a game or video encoding or HD movie rendering, but also sometimes crashes when I'm doing nothing after a first crash the system is very unstable and sometimes it crashes even during POST, or doesn't boot at all Some months ago I went to a local service (one that you just put your computer on the table and sit there with a guy and trying to figure out the problem, very rare these days) and they used OCCT and it crashed every time he changed some part to test it out (PSU, RAM, video card, HDD). The last one was the CPU. They changed the CPU and it didn't crash any more. Then when they put my CPU back, it also didn't crash. We figured that the trouble was the thermal paste (probably some 2 years old) because it was the only thing changed while testing. Up until 2 weeks ago, I haven't had any more problems. 2 weeks ago the problems reappeared. I changed again the thermal paste, put some Arctic Silver 5, and for about a week everything worked perfect (tried some games, video encoding, no more crashes). But again it started crashing in the same fashion as the first time. But now, instead, I figured out a very odd behaviour: when I start some of the apps above, in most cases it crashes if I start OCCT and turn on the CPU test, and run any of the programs above, it doesn't crash, even if the CPU is on 100% load (and 65-70 degrees Celsius temperature) if I shut down OCCT and continue using the programs, it crashes in a very short period of time (even if the CPU is on 5-10% load and 40 degrees) There are so many patterns and temporary solutions that I figured out in this year and a half period of time, that I can't include them all because I don't know which one are more relevant, but I'll happily provide any details you ask. My system is: CPU: AMD Phenom II X4 965 (3400 MHz - 125W) MB: ASUS M4A79XTD - EVO RAM: Corsair Vengeance 8 GB (2 x 4GB) CL8 1600MHz Video: HIS Radeon HD5770 1GB PSU: Corsair 750W HDD: Western Digital 1TB OS: Win 7 Enterprise 64 BIT (also tried with Windows Server 2008 R2 Trial and Win XP)

  Read the article

• Getting an boot error when starting computer

  - by Rob Avery IV

  I was in the middle of watching a movie on Netflix, then suddenly everything started crashing. First, explorer.exe closed down, then Google chrome. I had multiple things running in the background (Steam, Raptr, etc.). Individuality, each of those apps closed down also. When they did, a small dialog box popped up for each of them, one at a time, saying that it was missing a file, it couldn't run anymore, or something similar to that. It also had some jumbled up "code" with numbers and letters that I couldn't read. Ever since then, everytime I turn my computer on, it will run for a few seconds and give this error "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". No matter how many times I try to reboot it, it always gives me the same error. A day later after this happened I was able to start the computer, but before it booted, it told me that I didn't shut down the computer properly and asked how I wanted to run the OS (Run Windows in Safety Mode, Run Windows Normally, etc.). Once I logged, everything went SUPER slow and everything crashed almost instantly. The only thing I opened was Microsoft Security Essentials and only got in about two clicks before it was "Not Responding". Then, after that the whole computer froze and I had to restart it. Now, it's back to saying what it originally said, "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". I built this PC back in February 2012. Here are the specs: OS: Windows 7 Ultimate CPU: AMD 8-core GPU: Nvidia GTX Force 560 Ti RAM: 16GB Hard Drive: Hitachi Deskstar 750GB I'm usually very good taking care of my PC. I don't download anything that's not from a trusted site or source. I don't open up any spam email or such or go to any harmful websites like porn or stream movies. I am very clean with the things I do with my PC and don't do many DIFFERENT things with it. I use it pretty often especially for video games and doing homework in Eclipse. Also, good to note that I don't have any Norton or antisoftware installed. I have Microsoft Security Essentials installed but never did a scan. Thanks!

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >