Search Results

Search found 5723 results on 229 pages for 'turing machines'.

Page 179/229 | < Previous Page | 175 176 177 178 179 180 181 182 183 184 185 186  | Next Page >

• Samba and Windows 7

  - by John Gaughan

  I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

  Read the article

• Basic multicast network performance problems

  - by davedavedave

  I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

  Read the article

• subdomains to different VMs on one IP address

  - by efbenson

  I have a setup at home with an ESXi server Freenas server and several win7 clients. I have a domain refactoringme.com I set the @ and WWW domain record to my (current) IP address. I then forwarded port 80 to my local win2k3 server on my Linksys router and used host name matching to run the 5 test sites I have. That all works. Now I want to use the turnkey machines and move to dedicated VM servers. One for a wiki one for SVN etc. So how do I get www.refactoringme.com to go to one internal IP address and wiki.refactoringme.com to different internal IP address, while they both use the same external IP address? I added the additional record for wiki to my domain and pointed it to @. I figured it had to be involving a real firewall. So I installed PFSense on a VM and set it on the DMZ on my Linksys. From this point I haven't had any luck. I thought that maybe it would be in the DNS Forwarder or maybe in the Rules sections but neither have worked. Am I doing it wrong or on the right track but am missing something. Thanks for all the help.

  Read the article

• Live Mesh starts exactly once on fresh Win7 Ultimate installation

  - by Reb.Cabin

  I did a fresh install of Windows 7 Ulimate 64-bit on a formatted drive on a refurbed Lenovo PC, applied all 102 (!) windows updates, windows seems to be working fine. No quirks installing, no apps, no junkware, just straight, legal, Win7 Ultimate right from an unopened 2009 Microsoft box. Ok, breathe sigh -- Install Live Mesh (no messenger, no mail, no writer, no photo, none of the rest of the Windows Live freeware). Set up my shares, let it run overnight. watch MOE.exe in the Task-Manager perf pane to make sure it's all settled down. reboot. Ok, check that MOE is running and files are getting updated properly from other machines in the mesh. Great. HOWEVER -- when I try to launch Windows Live Mesh app from the Start jewel, I get a brief hourglass, then nothing. Reboot. Same story. result -- the shares I already posted seem to be synching properly, but I can't run the app, so I can't add and delete shares. The background process MOE seems to run, but I can't get the app going. btw, the reason I did this fresh install is I had exactly the same experience running Vista, so I wiped the machine hoping it would solve this nasty problem. Imagine my surprise! Will be grateful for clues, advice, etc, please & thanks!

  Read the article

• Migrating mysql 4 to mysql 5

  - by Lennart Regebro

  This seems to me to be a common use case, so I'm surprised so little information is about it, so sorry if it's a duplicate, but I have searched. :) I'm migrating a clients website from one CMS to another, and of moving to newer faster machines all at the same time. As a part of this I'm moving a MySQL database from the old server to the new ones. The problem is that the old server runs MySQL 4 and the new MySQL 5. So when i do a mysqldump at the old site and then try to run it on the new site I get syntax errors. ERROR 1064 (42000) at line 178: You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'BTREE (`id`), KEY `f_ChangedOnWeb` (`f_ChangedOnWeb`), KEY `f_AddressUpdate`' at line 56 I also tried to use an even older syntax by dumping with --compatible mysql323, but that just resulted in ERROR 1062 (23000) at line 2283: Duplicate entry '??????????' for key 2`... It seems to me this must be a reasonably common use case, yet I can't find any sort of help on this. Possibly all my Google searches just drown in irrelevant answers. Most seem to agree that mysqldump is the right answer, but noone mentions that you can get syntax errors...

  Read the article

• Headless VirtualBox VM NAT Network

  - by dirt

  I have a remote linux server accessible through SSH only. My goal is to host multiple Virtual Machines on this host server using VirtualBox. The host server has 1 IP address, so NAT will be used to route to the VMs for example 10022 will forward to server1:22 and 20022 will forward to server2:22. I have installed VirtualBox and copied a pre-configured CentOS VM to the host server. I start the VM, but cannot establish a connection to the server for example ssh -p 10022 127.0.0.1 times out. I've tried many things: Method 1: Copied existing .vdi, attached to new VM Method 2: Imported .Ova VM (thought it would help any MAC re-init issues?) NAT network type, tried natnet1 192.168/16 and 10.0/16 VBoxManage modifyvm "hermes.awoms.com" --natnet1 "192.168/16" Port forwarding with and without specifying VM ip in modifyvm --natpf1 command VBoxManage modifyvm "hermes" --natpf1 "guestssh,tcp,,10022,,,22" VBoxManage modifyvm "hermes" --natpf1 "guestssh,tcp,,10022,192.168.0.15,22" I can't see if VM is even booting (VBoxHeadless "hermes" --start & runs with no errors) I can't tell if VM is getting an IP address Is there anything else I can do to get more information from VirtualBox or the VM starting up when the only access I have is SSH?

  Read the article

• How to get robocopy running in powershell?

  - by Moo MinTroll

  I'm trying to use robocopy inside powershell to mirror some directories on my home machines. Here's my script: param ($configFile) $config = Import-Csv $configFile $what = "/COPYALL /B /SEC/ /MIR" $options = "/R:0 /W:0 /NFL /NDL" $logDir = "C:\Backup\" foreach ($line in $config) { $source = $($line.SourceFolder) $dest = $($line.DestFolder) $logfile = $logDIr $logfile += Split-Path $dest -Leaf $logfile += ".log" robocopy "$source $dest $what $options /LOG:MyLogfile.txt" } The script takes in a csv file with a list of source and destination directories. When I run the script I get these errors: ------------------------------------------------------------------------------- ROBOCOPY :: Robust File Copy for Windows ------------------------------------------------------------------------------- Started : Sat Apr 03 21:26:57 2010 Source : P:\ C:\Backup\Photos \COPYALL \B \SEC\ \MIR \R:0 \W:0 \NFL \NDL \LOG:MyLogfile.txt\ Dest - Files : *.* Options : *.* /COPY:DAT /R:1000000 /W:30 ------------------------------------------------------------------------------ ERROR : No Destination Directory Specified. Simple Usage :: ROBOCOPY source destination /MIR source :: Source Directory (drive:\path or \\server\share\path). destination :: Destination Dir (drive:\path or \\server\share\path). /MIR :: Mirror a complete directory tree. For more usage information run ROBOCOPY /? **** /MIR can DELETE files as well as copy them ! Any idea what I need to do to fix? Thanks, Mark.

  Read the article

• Updating Dell PowerEdge firmware on Ubuntu?

  - by Shtééf

  The company I work for recently got hands on a batch of second hand PowerEdge SC1425 machines. We'd like to put these to good use. Our operating system of choice is Ubuntu Server 10.04 64-bit, which installs just peachy on this type of machine. Now I'd like to install the firmware updates from Dell, which are apparently marked as recommended. This includes the updates for the BIOS, the BMC, and possibly some other hardware. I find it incredibly difficult to locate the files on the Dell website, and install any of them on an Ubuntu system: I downloaded the file OM_6.2.0_SUU_A01.iso. I believe I've read that the SUU DVD should be able to update any recent PowerEdge. Is this correct? Is this the latest version? Besides the version number, does A01 have any meaning? Is this image bootable? (At the moment, I just nosed around with a loop device mount.) Running /bin/bash ./suu from the DVD, I get: # /bin/bash ./suu ./suu: line 262: ./java/linux/i386/bin/java: No such file or directory The file exists and is executable, though. But I cannot execute it directly from the shell either.

  Read the article

• Which database to use and system/db administration by layman [closed]

  - by blah

  So my friend and I got briliant ;) idea for a business. Since it is not predictable whether it will work out or not, we decided to keep cost as low as possible to start with, in particular not to hire anyone. If it will work out as expected it will generate enough profit to hire professionals in few months. But for the first few months we'll be doing everything by ourselfs. He's a business/finance major, and I'm a software developer, so obviously I have to take care of IT :) It will be a webapp, written in python/django. My questions regarding this project: 1) What database should I choose? I'm experienced with oracle, and have been working with SQL Server for a while, but both of them are too expensive(at least now). It's a developer experience, I've never done any dba stuff. I'm looking for something free(as in beer). Looks like MySql or PostgreSQL are most popular in this sector. I would appreciate any comments on which db to choose. I'm open to any suggestions(it doesn't have to be MySql or Postgre). Here's what I know about data: It will be almost dates and numbers, a little bit of text. Searched mainly by dates. Data will almost never be updated, mostly inserted and browsed. From 30k to 300k new records/month. 2) Servers. My idea is to rent two dedicated servers. During normal operation one would be a web server(debian/apache), other would be a db server(debian/?). My recovery plan is to install everything on both, and in case of trouble with one of machines just run everything on the other one. Does it even makes sense? Any other tips appreciated. Thanks.

  Read the article

• Networking Problem MrxSmb event 50 "Delayed Write Failed" errors occurring all of the sudden

  - by Johnny Musso

  JUST THIS MONTH, we have started getting reports from a number of very stable clients that MrxSmb event id 50 errors keep appearing in their system event logs. Otherwise, they do not appear to have any networking problems except that there is a critical legacy application which seems to either be generating the MrxSmb errors or having errors occur because of them. The legacy application is comprised of 16 bit and 32 bit code and has not been changed or recompiled in many years. It has always been stable on Windows XP systems. The customers that have the problem usually have a small (5 clients or less) peer to peer network with all Windows XP systems. All service packs are loaded on the XP machines. Note: The only thing that seems to correct the problem is disabling opportunistic locking. I don't like this solution because it seems to slow down the network and sometimes causes record locking issues between users (on some networks). Also, this seems to have just started happening - as if a Windows update for XP has caused it? However, I have removed recent updates and it did not correct the issue. Thanks in advance for any help you can provide.

  Read the article

• error creating MS Exchange distribution list: Active directory response: 00000005: SecErr: DSID-031521D0

  - by BabakBani

  We've migrated a client from google apps to an MS Exchange 2010 SP2 on-premise setup. The setup /prepareAD went well, and the software was installed with the Administrator account. We've used the Exchange Management Console to setup mailboxes and had to google up the appropriate workarounds such as going into each users Advanced Security Settings and selecting "include inheritable permissions from this object's parents", and changing their logon-to from specific machines to "all computers" so that they can connect to Outlook Web Access, and in turn so their Outlook 2007-2010 clients can connect to Exchange. Sending and receiving emails are working well. Now that all this is in place, we can create Dynamic Distrubution Lists with no problem, but as soon as we try and create a DISTRIBUTION LIST, either in the EMC or the Exchange PowerShell, we get an error. As the error message in the powershell is more verbose, I include this if anyone can suggest how we remedy this: [PS] C:\Windows\system32new-DistributionGroup -Name 'projects' -SamAccountName 'projects' -Alias 'projects' Active Directory operation failed on DC.cppe.local. This error is not retriable. Additional information: Access is denied. Active directory response: 00000005: SecErr: DSID-031521D0, problem 4003 (INSUFF_ACCESS_RIGHTS), data 0 + CategoryInfo : NotSpecified: (0:Int32) [New-DistributionGroup], ADOperationException + FullyQualifiedErrorId : 1EA5CD3E,Microsoft.Exchange.Management.RecipientTasks.NewDistributionGroup

  Read the article

• Server Restart's and Respective Orders

  - by TheD

  EDIT:Not meaning to be disrespectful to any of the answers, but, the main question was whether rebooting a DC at the beginning of a cycle, then all the other servers, or rebooting it at the end once all the others are back online - is there a reason for doing it either way? I'm still not sure based on current responses. This will most likely seem like a fairly, maybe even stupid, question, but it's something I have been wondering about. As part of a regular process for clients servers are restarted remotely after patches and every client tends to have a similar order - but there always seems to be a small debate when it comes down to when do you reboot your DC. For example, 4 servers, 1 DC, 1xExchange, 1xBESX and 1xRandom, lets say it has some CRM software installed, is it best to reboot the DC first, then Exchange, then BESX and so on - or reboot all the servers, then reboot the DC last? - Perhaps it doesn't matter at all and it's just a case of how you have always done it. Would it change in a Hyper-V environment for example, with a physical DC, 1 VHost with all your servers virtualised on that Host? Rebooting the VHost and Virtual Machines first, then the DC at the end, or vice versa? Thanks!

  Read the article

• cPanel web servers mounting home partition to a NAS or SAN

  - by Scott

  I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

  Read the article

• Running DNS locally for home network

  - by Roy Rico

  I have a small home network that just got larger ( New roommate, My existing roommate got a laptop (on top of her computer)j, my friends coming over with laptop, etc ). I'd like to run a local DNS server for lookups of my local network stuff (fileserver.local, windowsTV.local, machineA.local, machineB.local, appletv.local). I used to have a business line with a static IP, and run bind/named internally. However, now, I have a normal account. My ISP's DNS servers are constantly changing (for whatever reasons my ISP doesn't like to keep the same IP range for long). I need my local DNS to be automatically updated to use my ISP's DNS for external traffic, but be able to maintain an internal DNS server (getting to update the hosts file is being a hassle with every new machine on top of rebuilding existing machines with win7 or Ubuntu 9.04). Additionally, My ISP's DNS servers often crash or become unresponsive. Are there any open DNS servers that are reliable (i don't want to reconfig every day) that I could use as my primary, then if those fail, then use my ISP's? UPDATE: Also looking for each workstation to be able to use dhcp to connect, but instead of getting ISP dns servers, getting my internal one.... Thanks

  Read the article

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• Debian network bridge configuration - /etc/network/interfaces

  - by Mathias

  I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl addbr xenbr0 ifconfig xenbr0 10.0.0.1 netmask 255.255.255.0 ifconfig xenbr0 up This works as expected, and domU interfaces are added to the bridge by Xen on VM start. My only problem is: how the heck do i specify this configuration in /etc/network/interfaces that it remains permanent and the bridge is available after a reboot? I tried the following config as found on a lot of tutorials: auto xenbr0 iface xenbr0 inet static address 10.0.0.1 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 bridge_stp no I get 2 different errors, depending on if the bridge already exists or not. If it doesn't exist: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). SIOCSIFADDR: No such device xenbr0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device xenbr0: ERROR while getting interface flags: No such device xenbr0: ERROR while getting interface flags: No such device Failed to bring up xenbr0. done. And if it exists: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.000000000000 no root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). RTNETLINK answers: File exists Failed to bring up xenbr0. done. Could anyone point me in the right direction please? The bridge works fine when created manually, i just need the right config file entries. The most tutorials I found add some devices to the bridge in the config, is that maybe the problem why it is not working? I don't have any interfaces I want to add to the bridge on creation as they get added later on VM start... Thanks, Mathias

  Read the article

• Finding cause of TCP retransmission within a LAN

  - by Surreal

  Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

  Read the article

• Passwordless SSH not working - keys copied and permissions set

  - by Comcar

  I know this question has been asked, but I'm certain I've done what all the other answers suggest. Machine A: used keygen -t rsa to create id_rsa.pub in ~/.ssh/ copied Machine A's id_rsa.pub to Machine B user's home directory Made the file permissions of id_rsa.pub 600 Machine B added Machine A's pub key to authorised_keys and authorised_keys2: cat ~/id_rsa.pub ~/.ssh/authorised_keys2 made the file permissions of id_rsa.pub 600 I've also ensured both the .ssh directories have the permission 700 on both machine A and B. If I try to login to machine B from machine A, I get asked for the password, not the ssh pass phrase. I've got the root users on both machines to talk to each other using password-less ssh, but I can't get a normal user to do it. Do the user names have to be the same on both sides? Or is there some setting else where I've missed. Machine A is a Ubuntu 10.04 virtual machine running inside VirtualBox on a Windows 7 PC, Machine B is a dedicated Ubuntu 9.10 server UPDATE : I've run ssh with the option -vvv, which provides many many lines of output, but this is the last few commands: debug3: check_host_in_hostfile: filename /home/pete/.ssh/known_hosts debug3: check_host_in_hostfile: match line 1 debug1: Host '192.168.1.19' is known and matches the RSA host key. debug1: Found key in /home/pete/.ssh/known_hosts:1 debug2: bits set: 504/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/pete/.ssh/identity ((nil)) debug2: key: /home/pete/.ssh/id_rsa (0x7ffe1baab9d0) debug2: key: /home/pete/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/pete/.ssh/identity debug3: no such identity: /home/pete/.ssh/identity debug1: Offering public key: /home/pete/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/pete/.ssh/id_dsa debug3: no such identity: /home/pete/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password

  Read the article

• Drive Mapped On Amazon EC2 Instance Startup Disconnected After Logon

  - by jsn

  I am launching an Amazon EC2 instance (Windows Server 2012), and on startup (though User Data field), it runs this powershell script: <powershell> NET CONFIG SERVER /AUTODISCONNECT:-1 # clear all prior connections net use * /delete /y > C:\delLog.txt 2>&1 # mount new drive net use R: \\dbHost\share /user:username pass /persistent:yes > C:\useLog.txt 2>&1 ipconfig /all > C:\ipLog.txt </powershell> When it launches and I connect to it through RDP, it shows in explorer "Diconnected Network Drive (R:). If I double click it, error message displays "R:\ is not accesible. Access id denied". Normally, it would ask me for credentials to reconnect. I need for this drive to be connected through the duration of the instance. delLog.txt contents: You have these remote connections: T: \\dbHost\share Continuing will cancel the connections. The command completed successfully. useLog.txt contents: The command completed successfully. ipLog.txt contents as expected. The net use commands works fine by itself, it connects. Anyone have any idea what could be wrong? There is only one account on these machines - Administrator. It is a samba share to a Linux server on a private network.

  Read the article

• ping/ssh networking problem with server from 1 particular windows xp laptop

  - by user47650

  I am experiencing an odd problem with one specific server at my data centre connecting from my laptop. Basically the server is accessible from other machines in my house, but not from 1 particular laptop which is running windows XP. I have setup tcpdump on the server and wireshark on the laptop, and I can see ping echo request and reply packets that actually make it back to the wireshark on the laptop, but nothing shows in the ping console output like so; $ ping xxx.55.32.255 Pinging xxx.55.32.255 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for xxx.55.32.255: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), But I can see from the wireshark on my local laptop that the ping reply gets back... No. Time Source Destination Protocol Info 46 3.964474 192.168.1.64 xxx.55.32.255 ICMP Echo (ping) request Frame 46 (74 bytes on wire, 74 bytes captured) Ethernet II, Src: Intel_31:d3:01 (00:19:d2:42:c3:01), Dst: ThomsonT_01:b8:2c (00:14:7f:02:b9:3c) Internet Protocol, Src: 192.168.1.64 (192.168.1.64), Dst: xxx.55.32.255 (xxx.55.32.255) Internet Control Message Protocol No. Time Source Destination Protocol Info 48 4.119060 xxx.55.32.255 192.168.1.64 ICMP Echo (ping) reply Frame 48 (74 bytes on wire, 74 bytes captured) Ethernet II, Src: ThomsonT_01:b8:2c (00:14:7f:01:b8:2c), Dst: Intel_21:c3:01 (10:20:d2:31:c3:01) Internet Protocol, Src: xxx.55.32.255 (xxx.55.32.255), Dst: 192.168.1.64 (192.168.1.64) Internet Control Message Protocol obviously I have disabled the windows firewall and there is nothing in the windows event log. There is nothing else obviously strange about the server as it is the same build as other servers that I can connect to fine.

  Read the article

• Computer Comparison - which is "better"

  - by David Murdoch

  A company I work with recently replaced their old server and gave it to me. Their old server is a Dell PowerEdge 2600. I've been playing with the machine and even installed Windows Server 2008 on it...and it seems to run it pretty well. Here are the specs for the two machines: Dev Machine: AMD Athlon64 3000+ 2.38 GHz (overclocked from 1.8GHz [@ 280x8.5] - it is stable-ish) Memory (RAM): 1x1GB OCZ PC3200 (Dual-Channel) 300GB HD OS: Windows XP Pro (32bit) SuperPi 1M digit test: 40 seconds Dell PowerEdge 2600 Server: Intel Xeon CPU 2.8GHz 2.8GHz Memory (RAM): 512MBx2 (PC2700, not dual channel) 68GB HD (RAID 5) OS: Windows Server 2000 (32bit) SuperPi 1M digit test: 56 seconds [using 1 processor] (Themes and Aero-Flass UI turned off, of course) I use my computer to regularly run Photoshop CS5, Illustrator CS5, Flash CS5, 5 browsers (Chrome, FF, IE, Safari, Opera), iTunes, Visual Studio 2010, and Kaspersky Internet Security 2010 [sometimes simultaneously :-) ]. The SuperPi test has my dev machine coming in about 30% faster than the Server machine...though this could be due to the server running "Vista" with background processes prioritized. Do you think it would be realistic/advantageous for me to move from my dev machine to the Dell PowerEdge 2600? Is it possible to install additional DVD drives/burners on the server? Can I install my internal 300 GB hard drive on the server? Can I add some USB 2.0 ports? Note: I'll probably install Win XP Pro on the dev machine if I do switch. If not, are there any creative and useful way for me to take advantage of this server (with the goal of faster computing)?

  Read the article

• Squid proxy in cent os often disconnected with error : tunnelConnectTimeout(): tunnelState->servers is NULL

  - by Ela

  I am having very often internet disconnection problem with Squid proxy service. My server config; OS: CentOS release 6.3 (Final) model name : Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz cpu MHz : 1600.000 My Local systems IP range:192.168.2.x Server IP: 192.168.2.11 Also this server is configured with lamp for development,Samba SMB file service manager and No svn currently. So i see maximum possibility is this squid proxy since this is where it stops to connect and am sure when i restart the server net started working so something wrong with this squid service only. And this server is connected with local 14 other windows machines and basically serves as a central development node. I am able to resolve it by restarting the server fully some time or sometimes by restarting the squid proxy which is totally killing our development. I have attached my cache log file here for the error info. Cache log file Sample error log: 2013/07/01 13:25:38| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:50| clientProcessRequest: Invalid Request 2013/07/01 13:26:05| tunnelConnectTimeout(): tunnelState->servers is NULL Some help can make our lives easier, Thanks in advance.

  Read the article

• PostgreSQL failover cluster on Windows Server

  - by user36997

  We are looking for advice on how to setup a basic failover cluster for our application: We will be using 4 machines running Microsoft Windows Server (most probably 2003). All four will always run our application, which is essentially a web service. Load balancing is "outsourced" - somebody else handles the distribution of the web requests among the servers. Only one of the servers will be running the PostgreSQL server actively at any given time. Another server (of the four) also has the DB installed, but is on standby/passive. The DB data is stored on shared storage. No copying data between servers. Reads are done very frequently by many end-users, and in rather small chunks of data. Writes are done much less frequently, by less users, and in very large bulks of data. Now, how can one configure Microsoft Cluster Service to keep only one instance of the DB server and 4 instances (1 per server) of our application at all times? And does PostgreSQL integrate neatly with MSCS at all? Update: Instead of keeping the data on shared storage, I also consider using log shipping to replicate data on a couple of DB servers. There are two issues with this option: Log shipping only makes sure that I have a second server that gets all of the data and is ready to take over. How do I implement the actual failure detection and failover switch? Switching back: Suppose the master fails and the system automatically fails over to the slave, and later the master comes back online. I understand that with WAL shipping this will require to reconfigure the log shipping once again, and that switching back is far from seamless. Is that so?

  Read the article

• MDT 2010 Litetouch.vbs Fails to Launch

  - by Mitch

  I have the custom image captured. Import the image and files. Prepare the customsettings.ini and the boot.ini to minimize the questions the deployment team will need to answer. Everything works like a charm on virtual machines but when I map to the scripts folder on the deployment share and double-click litetouch.vbs it creates the c:\minint folder, subfolders, and a couple of log files then nothing. Here's what the log files look like: <![LOG[Property LogPath is now = C:\MININT\SMSOSD\OSDLOGS]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[Property CleanStart is now = ]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[Microsoft Deployment Toolkit version: 5.1.1642.01]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[Property Debug is now = FALSE]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[GetAllFixedDrives(False)]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> Anyone encounter this before or know what might be happening/not happening and can direct me in the right way? I've only found a couple of other references to this anywhere and they had no solution/cause listed either. I'm stumped.

  Read the article

• How do I find information about a particular trojan? "W32/Smalltroj.XVGT", as reported by Norman

  - by Lasse V. Karlsen

  I tried checking the Norman antivirus page, Virus-descriptions, but sadly it seems Norman has intentionally obfuscated their search results (I tried clicking on W, and it seems they just list viruses with a W somewhere in the description, instead of more typical, all viruses with a name starting with a W.) Is there a common virus-list somewhere, or is it as I suspect, every antivirus manufacturer is free to come up with their own identification tags for each virus? Several "vshost32.exe" files, related to Microsoft Visual Studio 2008, has been quarantined on our server today, probably related to a test-deployment of some internal software. Some developer machines that have grabbed that latest version of our program has also had the same files quarantined. Now, these files should not have been deployed in the first case, so I'll be looking into that, but whenever any developer now builds a program locally and attempts to debug, the same file is placed in the build output directory, and promptly quarantined. Does anyone have any clues as to how I can go about verifying this before I pointedly ask the antivirus software to go take a hike on this particular virus? Edit: I've copied one of the quarantined files manually to a machine over the network that doesn't have antivirus installed, and compared the file on that machine with a local copy (on that machine) of the vshost32.exe template file, and they're bit-for-bit identical. I guess this is a false positive. I still would like to know if it would be possible for me to verify this in any other way though, since next time such a trojan might be reported in a compiled file that we won't have a pristine copy of.

  Read the article

< Previous Page | 175 176 177 178 179 180 181 182 183 184 185 186  | Next Page >