Search Results

Search found 16903 results on 677 pages for 'single responsibility'.

Page 18/677 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

  - by user450688

  Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

  Read the article

• How to get ISA 2006 Web Proxy to work with the Single Network Adapter template

  - by tronda

  I need to test an issue with running our application behind a proxy server with different type of configurations, so I installed ISA 2006 Enterprise on a desktop computer. Since this computer only has a single network card and I want to start out easy, I chose the "Single Network Adapter" template. We have a internal NAT'ed network which is in the 10 range. I have defined the internal network on the ISA server to be 10.XXX.YY.1 - 10.XXX.YY.255 I also have the Default rule which denies all traffic, but I've added the following Rule: Policy - Protocols - From - To Accept HTTP Internal External HTTPS Local Host Internal HTTS Server Localhost Then I configured Internet Explorer on a virutal machine running XP within virtualbox with Brigded network (gets same network address range as regular computers on our network) similar to this Instead of the server name I used the IP address. When I try to access a web page, this doesn't go through and I get the following log messages on the proxy server: Original Client IP Client Agent Authenticated Client Service Referring Server Destination Host Name Transport HTTP Method MIME Type Object Source Source Proxy Destination Proxy Bidirectional Client Host Name Filter Information Network Interface Raw IP Header Raw Payload GMT Log Time Source Port Processing Time Bytes Sent Bytes Received Cache Information Error Information Authentication Server Log Time Client IP Destination IP Destination Port Protocol Action Rule Result Code HTTP Status Code Client Username Source Network Destination Network URL Server Name Log Record Type 10.XXX.YY.174 - TCP - - - 24.08.2010 13:25:24 1080 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.174 10.XXX.YY.175 80 HTTP Initiated Connection MyHTTPAccess 0x0 ERROR_SUCCESS Internal Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:24 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.159 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.159 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 10.XXX.YY.166 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.166 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 0.0.0.0 Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Yes Proxy 10.XXX.YY.175 TCP GET Internet - - - Req ID: 096c76ae; Compression: client=No, server=No, compress rate=0% decompress rate=0% - - - 24.08.2010 13:25:27 0 2945 2581 446 0x0 0x40 24.08.2010 06:25:27 10.XXX.YY.174 10.XXX.YY.175 80 http Failed Connection Attempt MyHTTPAccess 10061 anonymous Internal Local Host http://www.vg.no/ PROXYTEST Web Proxy Filter 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:27 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:27 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall

  Read the article

• Validate a single property with the Fluent Validation Library for .Net

  - by Blegger

  Can you validate just a single property with the Fluent Validation Library, and if so how? I thought this discussion thread from January of 2009 showed me how to do it via the following syntax: validator.Validate(new Person(), x => x.Surname); Unfortunately it doesn't appear this works in the current version of the library. One other thing that led me to believe that validating a single property might be possible is the following quote from Jeremy Skinners' blog post: "Finally, I added the ability to be able to execute some of FluentValidation’s Property Validators without needing to validate the entire object. This means it is now possible to stop the default “A value was required” message from being added to ModelState. " However I do not know if that necessarily means it supports just validating a single property or the fact that you can tell the validation library to stop validating after the first validation error.

  Read the article

• Eliminating code duplication in a single file

  - by Jon

  Sadly, a project that I have been working on lately has a large amount of copy-and-paste code, even within single files. Are there any tools or techniques that can detect duplication or near-duplication within a single file? I have Beyond Compare 3 and it works well for comparing separate files, but I am at a loss for comparing single files. Thanks in advance. Edit: Thanks for all the great tools! I'll definitely check them out. This project is an ASP.NET/C# project, but I work with a variety of languages including Java; I'm interested in what tools are best (for any language) to remove duplication.

  Read the article

• OpenLayers, Layers: Tiled vs. single tile

  - by Chau

  Each time we add a new layer to our OpenLayers based website (data provided primarily by a GeoServer server), we discuss whether to use a single-tile or a tiled approach. Some of the parameters we evaluate are the following: Using the tiled approach we get: Slow but continuous buildup of the viewport Lots of small images Client side caching possibilities Blocking of the loading pipeline (6 requests at a time) Jerky feeling when navigating during load Using the single-tile approach we get: Smoother feeling when navigating during load Time delay before layer is loaded One large image for each layer No caching of the single tile We have a lot of data editing in the layers, thus a tile-cache might not be that efficient. Are there any best-practices when it comes to tiling? Progressing towards infinitely fast hardware and unlimited data connections, the discussion becomes irrelevant, but what configuration do you percieve as the most user-pleasing?

  Read the article

• How to store arrays in single array

  - by Jessy

  How can I store arrays in single array? e.g. I have four different arrays, I want to store it in single array int storeAllArray [] and when I call e.g. storeAllArray[1] , I will get this output [11,65,4,3,2,9,7]instead of single elements? int array1 [] = {1,2,3,4,5,100,200,400}; int array2 [] = {2,6,5,7,2,5,10}; int array3 [] = {11,65,4,3,2,9,7}; int array4 [] = {111,33,22,55,77}; int storeAllArray [] = {array1,array2,array3,array2} // I want store all array in on array for (int i=0; i<storeAllArray; i++){ System.out.println(storeAllArray.get[0]); // e.g. will produce --> 1,2,3,4,5,100,200,400 , how can I do this? }

  Read the article

• How to generate two XML files from a single HL7 file and insert both into two different columns as a single record?

  - by Vivek Ratnaparkhi

  I have Source Connector Type as 'File Reader' which is reading HL7 files and Destination Connector Type as 'Database Writer'. My database table has two columns Participant_Information SPR_Information I want to transform a single HL7 file into two XML files one for Participant_Information column and other for SPR_Information column and need to insert both as a single record into the database table. I'm able to insert one XML at a time but not able to find the way to insert both the XMLs as a single record into the database table. Any help is really greatly appreciated!

  Read the article

• Console appliction with Multithreading on Single core.

  - by Harsha

  Hello all, I am reposting my question on Multithreading on Single core processor. Original question is: http://stackoverflow.com/questions/2856239/will-multi-threading-increase-the-speed-of-the-calculation-on-single-processor I have been asked a question, At any given time, only one thread is allowed to run on a single core. If so, why people use multithreading in a application. Lets say you are running console application and It is very much possible to write the application to run on the main thread. But still people go for multithreading.

  Read the article

• syntax for single row MERGE / upsert in SQL Server

  - by Jacob

  I'm trying to do a single row insert/update on a table but all the examples out there are for sets. Can anyone fix my syntax please: MERGE member_topic ON mt_member = 0 AND mt_topic = 110 WHEN MATCHED THEN UPDATE SET mt_notes = 'test' WHEN NOT MATCHED THEN INSERT (mt_member, mt_topic, mt_notes) VALUES (0, 110, 'test') Resolution per marc_s is to convert the single row to a subquery - which makes me think the MERGE command is not really intended for single row upserts. MERGE member_topic USING (SELECT 0 mt_member, 110 mt_topic) as source ON member_topic.mt_member = source.mt_member AND member_topic.mt_topic = source.mt_topic WHEN MATCHED THEN UPDATE SET mt_notes = 'test' WHEN NOT MATCHED THEN INSERT (mt_member, mt_topic, mt_notes) VALUES (0, 110, 'test');

  Read the article

• sql server 2005 - return single row when 2 records in right table

  - by Peanut

  Hi, I have two related sql server tables ... TableA and TableB. ***TableA - Columns*** TableA_ID INT VALUE VARCHAR(100) ***TableB - Columns*** TableB_ID INT TableA_ID INT VALUE VARCHAR(100) For every single record in TableA there are always 2 records in TableB. Therefore TableA has a one-to-many relationship with TableB. How could I write a single sql statement to join these tables and return a single row for each row in TableA that includes: a column for the VALUE column in the first related row in table B a column for the VALUE column in the second related row in table B? Thanks.

  Read the article

• Serial connection over a single USB cable (Windows to linux, or linux to linux)

  - by andyortlieb

  I'm helping out with a project for an embedded device that only has USB and no serial. This device is running Linux. These days, when we need to connect to a serial port on a device we typically use a USB to serial adapter (on something like a phone system or a load balancing device, etc). I would like to know if it is possible to have the host device behave as though it were a serial adapter, thus removing the need for one. Given the nature of USB, is this approach even necessary? To recap, I would like to be able to connect a single A-to-A USB cable from my workstation (be it windows or linux) to this device, for the purpose of administration (especially initial setup), using minicom, putty or hyperterminal. Thanks

  Read the article

• Multiple email accounts in a single personal folder in Outlook 2007

  - by Neoclearyst

  I have an account with on Yahoo! Mail, another on Gmail. In Outlook 2007, I've set them up so that I can access them without having to go to their websites. I've password protected my personal folder, but can't find a way to merge my accounts into one personal folder. When I want to switch between my accounts, I must type my password again. Besides that, I can't check for new mail messages in both accounts at the same time. How do I merge multiple email accounts into one single personal folder on Outlook 2007?

  Read the article

• How to configure Apache so all requests go to single CGI file

  - by fastmonkeywheels

  I'm porting a CGI application from an embedded web server to run under Apache. In the effort of changing the least amount required I'm trying to figure out how to configure Apache so any requests coming in go to my CGI program, which then will use the QueryString environmental variable to determine which file needs to be created. I have Apache working now to where it will process my CGI file if it's requested directly i.e. localhost/cgi-bin/cgi_test.out but I need to figure out how to get my application to be called whenever any file is requested: localhost/ - call my application with QueryString set to "" or "/" localhost/thisFile - call my application with QueryString set to "/thisFile" etc. I have been doing all of my configuration testing under /etc/apache2/sites-available/mysite, which has been enabled and the default disabled. Thanks for any help. I've tried the recommendation from here: http://serverfault.com/questions/56082/configure-apache-to-handle-all-requests-via-single-index-php but I keep getting circular redirects.

  Read the article

• Dual Exchange 2010 on different VM + single public IP + multiple domains

  - by Shivan Raptor

  Here is the scenario: I have 2 Exchange Server 2010 on 2 different Virtual Machines, created by and based on Hyper-V. They have IP and domain: 192.168.5.11, domainA.com ; and 192.168.5.12, domainB.com respectively. The problem is, I only have 1 public IP, say 123.123.1.1 . How do I configure the settings so that I can successfully receive emails using both Exchange servers? Given that I cannot use single Exchange server for multiple domains. -- UPDATE -- To clarify, the domainA.com and domainB.com mentioned above are website domains, instead of multiple Active Directory forests. Users of the two Exchange Server shares the same Active Directory. I know that ONE Exchange Server can handle multiple domains, but I would like to separate them into different Virtual Machines, for load balancing and data separation.

  Read the article

• Using Y split cables to connect two servers to a single PDU receptacle

  - by sagi

  We have bought a few 30amp 208v PDUs that only have 9 receptacles. The servers we are connecting to those PDUs will not use the full 30amps (at 80%, or actually 40% since we use redundant power) so we need to find a way to connect more than 9 servers to the same 9 receptacles so we'll be not wasting capacity that we pay for. I thought about using a Y split cable like this one: http://www.cablesandkits.com/power-cord-c14-c13-splitter-cable-awg-p-515.html That will let me connect two servers to a single receptacle. Each of the individual receptacles can provide 12 amps of power and individual servers are unlikely to consume more than 3 amps at maximal load so it should provide sufficient power. The question is if there is any other reason why this may be a bad idea and if there is any other solution other than buying PDUs with more receptacles (which I don't want to do because I must use horizontal PDU on these racks and ones with more receptacles consume more U space).

  Read the article

• Single/Mulitple LUN for vmware vm hosting

  - by Yucong Sun

  I'm building a iscsi storage system for hosting about ~500 Vmware vm running concurrently. And I have a disk array with 15 disks, I only need moderate write performance but preferably not SPOFed. so, that leaves me with RAID1 / RAID10 , I have couple choices: 1) 3x LUN 4disk RAID10 + 3 hot-swap 2) 1x LUN 14disk RAID10 + 1 hot-swap 3) 7x LUN 2disk RAID1 + 1 host-swap Which way is better? Is there a real problem running 500 vms on single LUN? and would it be better to resort to 7 LUns so each VM is better isolated with each other?

  Read the article

• Associating multiple data with a single entry in Open Office Base

  - by idyllhands

  I'm trying to build a database that I can use to track prices of groceries on certain dates. My problem is that I cannot figure out how to have a single entry associate with multiple data. For example, carrots. The index would be carrots. Then, a few categorizing fields (ie, Produce|Vegetable) Then, I can enter a price, date that the price was valid, store that was selling for said price, etc. And the next time I buy carrots, I can just add a new set of pricing data that would be associated with the original carrots entry. I know very little about database building, so if anyone has something I could just modify, I would greatly appreciate it. Alternatively, a step by step tutorial would be great.

  Read the article

• Rerouting traffic from port 80 to another port on a single ip

  - by zam

  I have a server with multiple IP addresses associated with it. I'm trying to run a node.js web server (which I do not want to run as root), using only one of those ip addresses (it would be very bad if the traffic from all the ip addresses were forwarded). Through searching superuser, it looked like this could be possible with iptables: How to setting up iptables for traffic fowarding on port 80 from specific sources iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 80 --source 212.333.111.222 -j REDIRECT --to-port 9020 However, I do not understand why eth0 is needed. According to: http://blog.softlayer.com/2011/iptables-tips-and-tricks-port-redirection/ this could be done with: iptables -t nat -A PREROUTING -p tcp --dport 2525 -j REDIRECT --to-ports 25 What is the correct way of forwarding traffic from a single ip on port 80, lets say 111.111.111.111:80 to another port on the same server, lets say 111.111.111.111:8765? thanks for your help!

  Read the article

• How to grow from single server setup

  - by Jenkz

  I'm looking for resources on how to grow our server setup. We currently have one dedicated server with Rackspace in the UK of the following spec: HPDL385_G2_PrevGen HP Single Dual Core Opteron 2214 (2.2Ghz) 4GB RAM 2x 10,000 SCSI Drives in RAID 1 Our traffic is up to 550,000 UVs per month. The site runs off a PHP and MySQL setup. The database gets an absolute hammering, we have many complex queries joining multilpe tables. We are using APC for PHP caching. I'm getting to the stage where I've done as much DB and query optimisation as I can and wonder what the next step should be...... I've looked at memcache, but I've got the impression that his requires a large amount of RAM and ideally a dedicated box.... So is the next step to have two boxes; one for database, one for Apache? Or is there a step I've overlooked. Our load is usually around the 2 mark, but right now it's up at 20!

  Read the article

• How to grow from single server setup

  - by Jenkz

  I'm looking for resources on how to grow our server setup. We currently have one dedicated server with Rackspace in the UK of the following spec: HPDL385_G2_PrevGen HP Single Dual Core Opteron 2214 (2.2Ghz) 4GB RAM 2x 10,000 SCSI Drives in RAID 1 Our traffic is up to 550,000 UVs per month. The site runs off a PHP and MySQL setup. The database gets an absolute hammering, we have many complex queries joining multilpe tables. We are using APC for PHP caching. I'm getting to the stage where I've done as much DB and query optimisation as I can and wonder what the next step should be...... I've looked at memcache, but I've got the impression that his requires a large amount of RAM and ideally a dedicated box.... So is the next step to have two boxes; one for database, one for Apache? Or is there a step I've overlooked. Our load is usually around the 2 mark, but right now it's up at 20!

  Read the article

• Single sign-on for intranet?

  - by Jason Swett

  I'm trying to set up a single sign-on for my intranet. I've found a couple solutions online but I'm not sure if they apply to my particular situation. I have several subdomains on the same server. One level of user should be able to access all subdomains and another level of user should only be able to access some subdomains. Signing into one subdomain should make it so you don't have to log into any others. Can anyone point me in the right direction? I'm on Ubuntu using Apache.

  Read the article

• openwrt uses a single interface bridge?

  - by timbo

  My understanding of bridging is that it ties together two interfaces at layer 2. I am looking at a Ubiquiti Nanostation2 running OpenWRT that has an ethernet port 'eth0' and a wifi port 'ath0'. The ethernet port (the 'wan' port) is not part of the bridge and the bridge is just a single interface. Can anyone clarify this? - seems very different to Ubuntu. /etc/config/network: config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' config 'interface' 'wifi' option 'ipaddr' '192.168.13.1' option 'type' 'bridge' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ifname' 'wifi0'

  Read the article

• Adding a single 300Gb SCSI drive to poweredge 2850

  - by John Steele

  I have a 2850 setup with 3 146Gb drives, two partitions 1 12GB system with server 2003 sp2 and 1 261Gb Data. I am strapped on disk space on the data partition having to push data around. I wanted to add a 300Gb single drive for lesser critical data, is this possible? Or is it best to add 2 300Gb drives for another RAID 1 configuration? This is my church network and while it is mission critical it is not enterprise so I can take it down for a few hours. Any pointers to documentation or direct help would be greatly appreciated. John

  Read the article

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• Apache whitelist a single location, but require basic auth for everything else

  - by Chris Lawlor

  I'm sure this is simple, but Google is not my friend this morning. The goal is: /public... is openly accessible everything else (including /) requires basic auth. This is a WSGI app, with a single WSGI script (it's a django site, if that matters..) I have this: <Location /public> Order deny,allow Allow from all </Location> <Directory /> AuthType Basic AuthName "My Test Server" AuthUserFile /path/to/.htpasswd Require valid-user </Directory> With this configuration, basic auth works fine, but the Location directive is totally ignored. I'm not surprised, as according to this (see How the Sections are Merged), the Directory directive is processed first. I'm sure I'm missing something, but since Directory applies to a filesystem location, and I really only have the one Directory at /, and it's a Location that I wish to allow access to, but Directory always overrides Location... EDIT I'm using Apache 2.2, which doesn't support AuthType None.

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >