Search Results

Search found 5301 results on 213 pages for 'unknown (yahoo)'.

Page 193/213 | < Previous Page | 189 190 191 192 193 194 195 196 197 198 199 200  | Next Page >

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• Sendmail Tuning For Batch Mail Jobs

  - by Kyle Brandt

  I have a webservers that send out emails to a sendmail relay server as a batch job. The emails need to be accepted by the relay sendmail server as fast as possible, however, they do not need to go out (be relayed) very quickly. I am seeing a couple timeouts once and a while from the webserver trying to connect to the relay server. The load currently is about 30 emails a second for a couple minutes. There are quite a few tuning options for sendmail in the sendmail tuning guide. What I am focusing on now is the Delivery Mode: Delivery Mode There are a number of delivery modes that sendmail can operate in, set by the DeliveryMode ( d) configuration option. These modes specify how quickly mail will be delivered. Legal modes are: i deliver interactively (synchronously) b deliver in background (asynchronously) q queue only (don't deliver) d defer delivery attempts (don't deliver) There are tradeoffs. Mode i gives the sender the quickest feedback, but may slow down some mailers and is hardly ever necessary. Mode b delivers promptly but can cause large numbers of processes if you have a mailer that takes a long time to deliver a message. Mode q minimizes the load on your machine, but means that delivery may be delayed for up to the queue interval. Mode d is identical to mode q except that it also prevents lookups in maps including the -D flag from working during the initial queue phase; it is intended for ``dial on demand'' sites where DNS lookups might cost real money. Some simple error messages (e.g., host unknown during the SMTP protocol) will be delayed using this mode. Mode b is the usual default. If you run in mode q (queue only), d (defer), or b (deliver in background) sendmail will not expand aliases and follow .forward files upon initial receipt of the mail. This speeds up the response to RCPT commands. Mode i should not be used by the SMTP server. I currently have the CentOS default modes: Sendmail.cf: DeliveryMode=background Submit.cf: DeliveryMode=i Is sendmail.cf/mc for outgoing email from relay (to the intertubes) and sumbit.cf/mc for incoming eamil (from my webservers). Would it make sense to change the outgoing delivery mode to queue? If I did, what would the outbound email flow behave like? If this is the right thing to do, can anyone show me example mc configurations for this change? If it isn't, what recommendations are there for these constraints?

  Read the article

• Partition table corrupted (USB flash drive)

  - by 13ren

  It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

  Read the article

• udp expected behaviour not responding to test result

  - by ernst

  I have a local network topology that is structured as follows: three hosts and a switch in the middle. I am using a switch that supports 10,100,1000 Mbit/s full/half duplex connection. I have configured the hosts with a static ip 172.16.0.1-2-3/25. This is the output of ifconfig eth0 Link encap: Ethernet HWaddr ***** inet addr:172.16.0.3 Bcast:172.16.0.127 Mask:255.255.255.128 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 The output on H1 and H2 is perfectly matchable They are mutually reachable since i have tested the network with ping. I have forced the ethernet interface to work at 10M with ethtool -s eth0 speed 10 duplex full autoneg on this is the output of ethtool eth0 supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full S upported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Full Advertised pause frame use: Symmetric A dvertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) drv probe link timer ifdown ifup rx_err tx_err Link detected: yes – I am doing an experimental test using nttcp to calculate the GOODPUT in the case that H1 and H2 at the same time send data to H3. Since the three links have the same forced capability and the amount of arrving data speed is 10 from H1+10 from H2--20M to H3 it would be expected a bottleneck effect and, due to the non reliable nature of udp, a packet loss. But this doesn't appen since the output of nttcp application shows the same number of byte sended and received. this is the output of nttcp on h3 nttcp -T -r -u 172.16.0.2 & nttcp -T -r -u 172.16.0.1 [1] 4071 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 13.74 0.05 4.8848 1398.0140 2049 149.14 42684.8 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 14.02 0.05 4.7872 1398.0140 2049 146.17 42684.8 1 8388608 13.56 0.06 4.9500 1118.4065 2051 151.28 34181.1 1 8388608 13.89 0.06 4.8310 1198.3084 2051 147.65 36623.0 – How is this possible? Am i missing something? Any help will be gratefully apprecciated, Best regards

  Read the article

• Netcat file transfer problem

  - by thepurplepixel

  I have two custom scripts I just wrote to facilitate transferring files between my VPS and my home server. They are both written in bash (short & sweet): To send: #!/bin/bash SENDFILE=$1 PORT=$2 HOST='<my house>' HOSTIP=`host $HOST | grep "has address" | cut --delimiter=" " -f 4` echo Transferring file \"$SENDFILE\" to $HOST \($HOSTIP\). tar -c "$SENDFILE" | pv -c -N tar -i 0.5 | lzma -z -c -6 | pv -c -N lzma -i 0.5 | nc -q 1 $HOSTIP $PORT echo Done. To receive: #!/bin/bash SERVER='<myserver>' SERVERIP=`host $SERVER | grep "has address" | cut --delimiter=" " -f 4` PORT=$1 echo Receiving file from $SERVER \($SERVERIP\) on port $PORT. nc -l $PORT | pv -c -N netcat -i 0.5 | lzma -d -c | pv -c -N lzma -i 0.5 | tar -xf - echo Done. The problem is that, for a very quick second, I see something flash along the lines of "Connection Refused" (before pv overwrites it), and no file is ever transferred. The port is forwarded through my router, and nmap confirms it: ~$ sudo nmap -sU -PN -p55515 -v <my house> Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-21 18:10 EDT NSE: Loaded 0 scripts for scanning. Initiating Parallel DNS resolution of 1 host. at 18:10 Completed Parallel DNS resolution of 1 host. at 18:10, 0.00s elapsed Initiating UDP Scan at 18:10 Scanning 74.13.25.94 [1 port] Completed UDP Scan at 18:10, 2.02s elapsed (1 total ports) Host 74.13.25.94 is up. Interesting ports on 74.13.25.94: PORT STATE SERVICE 55515/udp open|filtered unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 2.08 seconds Raw packets sent: 2 (56B) | Rcvd: 5 (260B) Also, running netcat normally doesn't work either: squircle@summit:~$ netcat <my house> 55515 <my house> [<my IP>] 55515 (?) : Connection refused Both boxes are Ubuntu Karmic (9.10). The receiver has no firewall, and outbound traffic on that port is allowed on the sender. I have no idea what to troubleshoot next. Any ideas? P.S.: Feel free to move this to SO/SF if you feel it would fit better there.

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David Boike

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• Samba share not accessible from Win 7 - tried advice on superuser

  - by Roy Grubb

  I have an old Red Hat Linux box that I use, amongst other things, to run Samba. My Vista and remaining Win XP PC can access the p/w-protected Samba shares. I just set up a new Windows 7 64-bit Pro PC. Attempts to access the Samba shares by clicking on the Linux box's icon in 'Network' from this machine gave a Logon failure: unknown user name or bad password. message when I gave the correct credentials. So I followed the suggestions in Windows 7, connecting to Samba shares (also checked here but found LmCompatibilityLevel was already 1). This got me a little further. If click on the Linux box's icon in 'Network' from this machine I now see icons for the shared directories. But when I click on one of these, I get \\LX\share is not accessible. You might not have permission... etc. I tried making the Win 7 password the same as my Samba p/w (the user name was already the same). Same result. The Linux box does part of what I need for ecommerce - the in-house part, it's not accessible to the Internet. As my Linux Fu is weak, I have to avoid changes to the Linux box, so I'm hoping someone can tell me what to do to Win 7 to make it behave like XP and Vista when accessing this share. Help please!? Thanks Thanks for replying @Randolph. I had set 'Network security: LAN Manager authentication level' to Send LM & NTLM - use NTLMv2 session security if negotiated based on the advice in Windows 7, connecting to Samba shares and had restarted the machine, but that didn't work for me. I'll try playing with other Network security values. I have now tried the following: Network security: Allow Local System to use computer identity for NTLM: changed from Not Defined to "Enabled". Restarted machine Still says "\LX\share is not accessible. You might not have permission..." etc. Network security: Restrict NTLM: Add remote server exceptions for NTLM Authentication (added LX) Restarted machine Still says "\LX\share is not accessible. You might not have permission..." etc. I can't see any other Network security settings that might affect this. Any other ideas please? Thanks Roy

  Read the article

• How do I configure a site in IIS 7 for SSL with a wildcard certificate?

  - by michielvoo

  We have an Windows 2008 server with IIS 7 to test sites we develop for our clients. Each site has a binding on a subdomain: clienta.example.com clientb.example.com clientc.example.com (* Using example.com to protect the innocent) For one of these sites we now have to test if it works over https. So I have created a wildcard certificate request with *.example.com as the common name. I have received the certificate (issued by PositiveSSL SA) and completed the request. The certificate is now installed in IIS. Now I have added an https binding to the second site with the following settings: type: https IP address: All Unassigned Port: 443 Host name: clientb.example.com SSL certificate: *.example.com Browsing the site over regular http works fine. When I try to browse the site over https I get the following errors (depending on the browser used): Chrome This webpage is not available Error 102 (net::ERR_CONNECTION_REFUSED): Unknown error. Firefox Unable to connect Firefox can't establish a connection to the server at clientb.example.com Firebug says Status: Aborted Internet Explorer Internet Explorer cannot display the webpage I have checked Failed Request Tracing, and according to the log the request was completed with status 200. I have run the SSL Diagnostics Tool with the following result: System time: Fri, 04 Mar 2011 14:04:35 GMT Connecting to 192.168.2.95:443 Connected Handshake: 115 bytes sent Handshake: 3877 bytes received Handshake: 326 bytes sent Handshake: 59 bytes received Handshake succeeded Verifying server certificate, it might take a while... Server certificate name: *.example.com Server certificate subject: OU=Domain Control Validated, OU=PositiveSSL Wildcard, CN=*.example.com Server certificate issuer: C=GB, S=Greater Manchester, L=Salford, O=Comodo CA Limited, CN=PositiveSSL CA Server certificate validity: From 2-3-2011 1:00:00 To 2-3-2012 0:59:59 1:00:00 To 2-3-2012 0:59:59 HTTPS request: GET / HTTP/1.0 User-Agent: SSLDiag Accept:*/* HTTPS: 85 bytes of encrypted data sent HTTPS: 533 bytes of encrypted data received Status: HTTP/1.1 404 Not Found HTTP/1.1 404 Not Found Content-Type: text/html; charset=us-ascii Server: Microsoft-HTTPAPI/2.0 Date: Fri, 04 Mar 2011 14:04:35 GMT Connection: close Content-Length: 315 <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN""http://www.w3.org/TR/html4/strict.dtd"> <HTML><HEAD><TITLE>Not Found</TITLE> <META HTTP-EQUIV="Content-Type" Content="text/html; charset=us-ascii"></HEAD> <BODY><h2>Not Found</h2> <hr><p>HTTP Error 404. The requested resource is not found.</p> </BODY></HTML> HTTPS: server disconnected Final handshake: 37 bytes sent successfully Q: What can I do to make this work?

  Read the article

• Recover harddrive data

  - by gameshints

  I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

  Read the article

• How should I convert a physical drive to a VHD for use with VirtualPC?

  - by RBerteig

  I have the hard disks from a PC that was happily running Windows Me until is it suffered an unknown hardware failure. The drives are intact, and can be mounted and read on other PCs. We have data backups, but there is licensed software installed that may not be possible to migrate to newer versions running on a more modern platform making the idea of just booting a virtual image attractive. Is it possible to make VHDs from the drives such that I can boot them in VirtualPC? If not VirtualPC, would it be possible in any other virtualization tool? Edit: Some more details.... The system was running Windows Me, but upgraded from Windows 95 (or possibly 98). It can't have been more than a Pentium II, but I will have to look at the motherboard to confirm that. There were no "exotic" devices installed, and nothing beyond the usual legacy stuff that would need to survive into a virtual machine. The licensed software did not have a dongle, so I won't need to worry about virtualizing a physical dongle of some kind. Licenses were probably died to the disk serial number. There were two HDs, both IDE. The boot disk is about 6GB, and the spare data disk is 12GB, but nearly empty. I have a small bias in favor of VirtualPC just because its free and I've used it successfully in the past. But this is a good excuse to revisit the state of the art. I do know from direct experience that it is possible to install and boot DOS 5.0 and Win95 in VirtualPC, but the VM extensions weren't available so the experience isn't as seamless as I would have liked. A very old DirectX game that failed miserably under XP SP2 runs really nicely on that VM, and actually plays better in a lot of ways than it did on period hardware, so that gives me hope that this is possible. Edit 2: Well, I'm closer than I was when I asked... so thanks to all for helpful suggestions and hints to what I should be trying. I used WinImage to copy the disks, and VirtualPC 2007 to attempt to boot. So far, I have it booting in safe mode, but hanging with a black screen otherwise. I strongly suspect that the copy of Artisoft Lantastic 8.0 (anyone else remember them?) that is still installed for networking with even older PCs that mostly don't exist any more is the culprit there. In my infinite free time, I will try to resolve the differences between a Safe Mode boot and a normal boot, and feel that it is likely to yield to pressure. I'd accept more than one answer if I could... this isn't as black and white a question as the one accepted answer convention assumes.

  Read the article

• Hybrid gmail MX + postfix for local accounts

  - by krunk

  Here's the setup: We have a domain, mydomain.com. Everything is on our own server, except general email accounts which are through gmail. Currently gmail is set as the MX record. The server also has various email aliases it needs to support for bug trackers and such. e.g. [email protected] |/path/to/issuetracker.script I'm struggling with a setup that allows the following, both locally and from user's email clients. guser1 - has a gmail account and a local account guser2 - only has a gmail account bugs - has a pipe alias in /etc/aliases for issue tracker Scenarios mail to [email protected] from local host (crons and such) needs to go to gmail account mail to [email protected] from local host mail to [email protected] needs to be piped to the local issue tracker script So, the first stab was creating a transport map. In this scenario, the our server would be set as teh MX and guser* destined emails are sent to gmail. Put the gmail users in a map like so: [email protected] smtp:gmailsmtp:25 [email protected] smtp:gmailsmtp:25 Problems: Ignores extensions such as [email protected] Only works if append_at_myorigin = no (if set to yes, gmail refuses to connect with: E4C7E3E09BA3: to=, relay=none, delay=0.05, delays=0.02/0.01/0.02/0, dsn=4.4.1, status=deferred (connect to gmail-smtp-in.l.google.com[209.85.222.57]:25: Connection refused)) since append_at_myorigin is set to no, all received emails have (unknown sender) The second stab was to set explicit localhost aliases in /etc/aliases and do a domain wide forward on mydomain. This too requires setting the local server as the MX: root: root@localhost # transport mydomain.com smtp:gmailsmtp:25 Problems: * If I create a transport map for a domain that matches "$myhostname", the aliases file is never parsed. So when a local user (or daemon) sends an email like: mail -s "testing" root < text.txt Postfix ignores the /etc/alias entry and maps to [email protected] and attempts to send it to the gmail transport mapping. Third stab: Create a subdomain for the bugs, something like bugs.mydomain.com. Set the MX for this domain to local server and leave the MX for mydomain.com to the Gmail server. Problems: * Does not solve the issue with local accounts. So when the bug tracker responds to an email from [email protected], it uses a local transport and the user never receives the email. % postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_at_myorigin = no append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = $myhostname, localhost.$myhostname, localhost myhostname = mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_cert_file = /etc/ssl/certs/kspace.pem smtp_tls_enforce_peername = no smtp_tls_key_file = /etc/ssl/certs/kspace.pem smtp_tls_note_starttls_offer = yes smtp_tls_scert_verifydepth = 5 smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_destination smtpd_tls_ask_ccert = yes smtpd_tls_req_ccert = no smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport

  Read the article

• Setting font size of Closed Captions on iPhone using ffmpeg or mencoder

  - by forthrin

  Does anyone know how to either: Make ffmpeg set subtitle font size in the output video file Make mencoder produce an iPhone-compatible video file (with subtitles) I finally found out how to get Closed Captions video on iPhone, with mkv and srt files as source material. The secret was using the mov_text subtitle codec in ffmpeg (and turning on Closed Captions in the iPhone settings of course): ffmpeg -y -i in.mkv -i in.srt -map 0:0 -map 0:1 -map 1:0 -vcodec copy -acodec aac -ab 256k -scodec mov_text -strict -2 -metadata title="Title" -metadata:s:s:0 language=eng out.mp4 However, the font size appears very small on the iPhone, and I can't find out how to set it with ffmpeg (the iPhone has no option for this). I found out that mencoder has a -subfont-text-scale option, but I don't have a lot of experience with this program. The following, my best attempt so far, produces an output file which is not playable on the iPhone. sudo port install mplayer +mencoder_extras +osd mencoder in.mkv -sub in.srt -o out.mp4 -ovc copy -oac faac -faacopts br=256:mpeg=4:object=2 -channels 2 -srate 48000 -subfont-text-scale 10 -of lavf -lavfopts format=mp4 PS! As requested, here is the output from mencoder: 192 audio & 400 video codecs success: format: 0 data: 0x0 - 0xb64b9d2f libavformat version 54.6.101 (internal) libavformat file format detected. [matroska,webm @ 0x1015c9a50]Unknown entry 0x80 [lavf] stream 0: video (h264), -vid 0 [lavf] stream 1: audio (ac3), -aid 0, -alang eng VIDEO: [H264] 1280x544 0bpp 49.894 fps 0.0 kbps ( 0.0 kbyte/s) [V] filefmt:44 fourcc:0x34363248 size:1280x544 fps:49.894 ftime:=0.0200 ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders libavcodec version 54.23.100 (internal) AUDIO: 48000 Hz, 2 ch, s16le, 448.0 kbit/29.17% (ratio: 56000->192000) Selected audio codec: [ffac3] afm: ffmpeg (FFmpeg AC-3) ========================================================================== ** MUXER_LAVF ***************************************************************** REMEMBER: MEncoder's libavformat muxing is presently broken and can generate INCORRECT files in the presence of B-frames. Moreover, due to bugs MPlayer will play these INCORRECT files as if nothing were wrong! ******************************************************************************* OK, exit. videocodec: framecopy (1280x544 0bpp fourcc=34363248) VIDEO CODEC ID: 28 AUDIO CODEC ID: 15002, TAG: 0 Writing header... [mp4 @ 0x1015c9a50]Codec for stream 0 does not use global headers but container format requires global headers [mp4 @ 0x1015c9a50]Codec for stream 1 does not use global headers but container format requires global headers Then the following repeats itself for every frame: Pos: 0.0s 1f ( 2%) 0.00fps Trem: 0min 0mb A-V:0.000 [0:0] [mp4 @ 0x1015c9a50]malformated aac bitstream, use -absf aac_adtstoasc Error while writing frame. I recognize -absf aac_adtstoasc as an ffmpeg option (does mencoder spawn ffmpeg?), but I don't know how to pass this option on (my hunch is this is not even the origin of the problem).

  Read the article

• Linksys WiFi usb dongle and linux woes

  - by MrStatic

  I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

  Read the article

• Mixed sessions with Classic ASP on IIS 7.5 and Windows 2008 R2 64 bit

  - by Marcin

  Recently had an issues with a server upgrade from IIS 6 on Windows 2003 to IIS 7.5 on Windows 2008 R2 64 bit. We have a number of websites running on Classic ASP. All the sites sit under a particular site, e.g. www.example.com/foo and www.example.com/foobar. On IIS 6 each site was set up as a virtual directory and things worked fine. Since moving to the new set up, a lot of websites seem to have mixed Sessions. To be clear, this is not a app pool recycling issue; rather the sessions are populated with information when the user hits the site and while browsing they get sessions from different sites. We've determined this based on - a few customers called up and reported having their shopping cart with items with names of items belonging to a different site - also our own testing showed that some queries being run would try to bring products in from a different site We've tried - disabling dynamic caching - converting each site to be a virtual application (if I understand correctly, the virtual directory/application concepts were changed/refined somewhat in IIS 7 although to be honest, I'm not clear what the difference is) - various application pool changes (using .NET 2 framework), classic and integrated modes, changing the Process model to NetworkIdentity), all to no avail. The only thing we haven't tried is changing it to run as a 32 bit application. We're not using http only cookies, so when I open up a browser and type document.cookie into the dev console in Firefox/Chrome/IE that there will be multiple ASPSESSIONID=... values whereas previously I believe there was only one. Finally, we use server side JScript for the classic ASP pages, not VBScript, so we have code similar to the below. //the user's login account as a jscript object Session("user") = { email : "[email protected]", id : 123 }; and if we execute a line of code like below: Response.Write( typeof(Session("user")) ); When things are running correctly, we get "object" - as expected. When the Session gets trashed, the output is "unknown" and we are also unable to access the fields within the JScript object (e.g. the .email or .id fields). Much appreciated if anyone can provide any pointers about how to resolve this, everything on google seems to point to different issues.

  Read the article

• Nagios shell script cannot be executed

  - by MeinAccount

  I'm trying to monitor GitLab with nagios. I've created the following command definition and shell script but when checking the service I'm receiving the following e-mail. How can I solve this? The file is executable. [...] nagios : 3 incorrect password attempts ; TTY=unknown ; PWD=/ ; USER=git ; COMMAND=/bin/bash -c /var/lib/nagios/custom_plugins/check_gitlab.sh Command definition: define command { command_name custom_check_gitlab command_line /var/lib/nagios/custom_plugins/check_gitlab.sh } Shell script: #! /bin/sh # [...] RAILS_ENV="production" # Script variable names should be lower-case not to conflict with internal /bin/sh variables such as PATH, EDITOR or SHELL. app_root="/home/git/gitlab" app_user="git" unicorn_conf="$app_root/config/unicorn.rb" pid_path="$app_root/tmp/pids" socket_path="$app_root/tmp/sockets" web_server_pid_path="$pid_path/unicorn.pid" sidekiq_pid_path="$pid_path/sidekiq.pid" ### Here ends user configuration ### # Switch to the app_user if it is not he/she who is running the script. if [ "$USER" != "$app_user" ]; then sudo -u "$app_user" -H -i $0 "$@"; exit; fi # Switch to the gitlab path, if it fails exit with an error. if ! cd "$app_root" ; then echo "Failed to cd into $app_root, exiting!"; exit 1 fi ### Init Script functions check_pids(){ if ! mkdir -p "$pid_path"; then echo "Could not create the path $pid_path needed to store the pids." exit 1 fi # If there exists a file which should hold the value of the Unicorn pid: read it. if [ -f "$web_server_pid_path" ]; then wpid=$(cat "$web_server_pid_path") else wpid=0 fi if [ -f "$sidekiq_pid_path" ]; then spid=$(cat "$sidekiq_pid_path") else spid=0 fi } # Checks whether the different parts of the service are already running or not. check_status(){ check_pids # If the web server is running kill -0 $wpid returns true, or rather 0. # Checks of *_status should only check for == 0 or != 0, never anything else. if [ $wpid -ne 0 ]; then kill -0 "$wpid" 2>/dev/null web_status="$?" else web_status="-1" fi if [ $spid -ne 0 ]; then kill -0 "$spid" 2>/dev/null sidekiq_status="$?" else sidekiq_status="-1" fi } check_pids check_status if [ "$web_status" != "0" -a "$sidekiq_status" != "0" ]; then echo "GitLab is not running." exit 2 fi if [ "$web_status" != "0" ]; then printf "The GitLab Unicorn webserver is \033[31mnot running\033[0m.\n" exit 1 fi if [ "$sidekiq_status" != "0" ]; then printf "The GitLab Sidekiq job dispatcher is \033[31mnot running\033[0m.\n" exit 1 fi if [ "$web_status" = "0" -a "$sidekiq_status" = "0" ]; then printf "GitLab and all it's components are \033[32mup and running\033[0m.\n" exit 0 fi

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• Upgrading php from php 5.3 to 5.4 .7

  - by Takingsides

  So, quickly so to speak I have noticed this topic around, I have searched and there are plenty of solutions. However these solutions do not work for me, not only that but I'm intending to learn more about the Debian based OS. Questions I would like to know how to upgrade php5.3 to php 5.4.7 compiling it from source, myself without using a third-party ppa. Is the way (explained below) the correct way of configuring php5.4? I'm new to compiling from source. Set-up I run Ubuntu Server 12.04 64bit. I've currently got: PHP 5.3 MySQL-Server Apache2 Memcached The Problem So I initially installed php5.3 using apt-get. I now wish to upgrade the php 5.4 due to the advantage of traits in OOP and the struct with Arrays and all the other recent patches and such. Possible Solutions I've seen this ondrej/ppa repository, which I refuse to use, given the fact that it may work, but it's an unknown/untrusted source. ALso, i'm not learning how to administer from source, using configure, make and install accordingly. I've seen a solution compiling from source, which is essentially how I was hoping to go about it with some guidance. Conclusion So I didn't just expect to be spoon-fed, and I went out and did some manual reading and atleast started the ball rolling myself; this how far i've got. The first thing I did was su into root (to save the typing sudo all the darn time). $ sudo su The next thing I did was download the latest version of php (5.4.7) and extracted it's contents ready to configure before installing it. $ mkdir php5-new && cd !$ $ wget -O php-5.4.7.tar.bz2 http://php.net/get/php-5.4.7.tar.bz2/from/uk3.php.net/mirror $ bzip2 -d php-5.4.7.tar.bz2 $ tar xvf php-5.4.7.tar.gz $ cd php-5.4.7 $ ./configure --help Finally I decided to have a bash, I looked through the list of options and decided I needed to list ALL of the things I wanted to include in the configuration. $ ./configure --with-mysql --with-apache2 --with-libxml --with-openssl --with-zlib --with-bz2 --with-curl --with-dom --with-gd --with-imap --with-imap-ssl --with-mcrypt --with-mysqli --with-pdo-mysql --with-libxml --enable-ftp --enable-mbstring --enable-soap Finally, the results... When the configuration process had finished, it threw an error: configure: error: xml2-config not found. Please check your libxml2 installation.

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• nginx + php fpm -> 404 php pages - file not found

  - by Mahesh

  *2037 FastCGI sent in stderr: "Primary script unknown" while reading response header from upstream server { listen 80; ## listen for ipv4; this line is default and implied #listen [::]:80 default ipv6only=on; ## listen for ipv6 server_name .site.com; root /var/www/site; error_page 404 /404.php; access_log /var/log/nginx/site.access.log; index index.html index.php; if ($http_host != "www.site.com") { rewrite ^ http://www.site.com$request_uri permanent; } location ~* \.php$ { fastcgi_index index.php; fastcgi_pass 127.0.0.1:9000; #fastcgi_pass unix:/var/run/php-fpm/php-fpm.sock; fastcgi_buffer_size 128k; fastcgi_buffers 256 4k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; fastcgi_read_timeout 240; include /etc/nginx/fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param SCRIPT_NAME $fastcgi_script_name; } location ~ /\. { access_log off; log_not_found off; deny all; } location ~ /(libraries|setup/frames|setup/libs) { deny all; return 404; } location ~ ^/uploads/(\d+)/(\d+)/(\d+)/(\d+)/(.*)$ { alias /var/www/site/images/missing.gif; #i need to modify this to show only missing files. right now it is showing missing for all the files. } location ~* \.(jpg|jpeg|png|gif|ico|css|js)$ { access_log off; expires 20d; } location /user_uploads/ { location ~ .*\.(php)?$ { deny all; } } location ~ /\.ht { deny all; } } php-fpm config is default and is not touched. The problem is little strange for me. Error pages are showing File not found only if they are .php files. Other error files are clearly calling the 404.php file site.com/test = calls 404.php site.com/test.php = File not found. I am searching and making changes. but it hasn't solved the problem.

  Read the article

• NFS4 / ZFS: revert ACL to clean/inherited state

  - by Keiichi

  My problem is identical to this Windows question, but pertains NFS4 (Linux) and the underlying ZFS (OpenIndiana) we are using. We have this ZFS shared via NFS4 and CIFS for Linux and Windows users respectively. It would be nice for both user groups to benefit from ACLs, but the one missing puzzle piece goes thusly: Each user has a home, where he sets a top-level, inherited ACL. He can later on refine permissions for the contained files/folders iteratively. Over time, sometimes permissions need to be generalized again to avoid increasing pollution of ACL entries. You can tweak the ACL of every single file if need be to obtain the wanted permissions, but that defeats the purpose of inherited ACLs. So, how can an ACL be completely cleared like in the question linked above? I have found nothing about what a blank, inherited ACL should look like. This usecase simply does not seem to exist. In fact, the solaris chmod manpage clearly states A- Removes all ACEs for current ACL on file and replaces current ACL with new ACL that represents only the current mode of the file. I.e. we get three new ACL entries filled with stuff representing the permission bits, which is rather useless for cleaning up. If I try to manually remove every ACE, on the last one I get chmod A0- <file> chmod: ERROR: Can't remove all ACL entries from a file Which by the way makes me think: and why not? In fact, I really want the whole file-specific ACL gone. The same holds for linux, which enumerates ACEs starting with 1(!), and verbalizes its woes less diligently nfs4_setacl -x 1 <file> Failed setxattr operation: Unknown error 524 So, what is the idea behind ACLs under Solaris/NFS? Can they never be cleaned up? Why does the recursion option for the ACL setting commands pollute all children instead of setting a single ACL and making the children inherit? Is this really the intention of the designers? I can clean up the ACLs using a windows client perfectly well, but am I supposed to tell the linux users they have to switch OS just to consolidate permissions?

  Read the article

• Postfix issues sending mail to addresses under domain located on server

  - by iamthewit

  I recently installed virtualmin on my nice shiny new rackspace cloud. Everything went seemlessly but I've been having some issues getting emails to send properly. The problem seems to be that the server can not send mail to email addresses where the domain is owned by my server. For example, on my server I run multiple virtual domains, lets call this one test.com. When I run the mail command from shell (mail [email protected]) I get the following back from my maillog: Oct 6 14:55:18 test postfix/pickup[8737]: DC1131612CC: uid=0 from= Oct 6 14:55:18 test postfix/cleanup[8769]: DC1131612CC: [email protected] Oct 6 14:55:18 test postfix/qmgr[8738]: DC1131612CC: [email protected], size=353, nrcpt=1 (queue active) Oct 6 14:55:18 test postfix/error[8771]: DC1131612CC: [email protected], relay=none, delay=0, delays=0/0/0/0, dsn=5.0.0, status=bounced (User unknown in virtual alias table) Oct 6 14:55:18 test postfix/cleanup[8769]: DD07D1612D1: [email protected] Oct 6 14:55:18 test postfix/bounce[8772]: DC1131612CC: sender non-delivery notification: DD07D1612D1 Oct 6 14:55:18 test postfix/qmgr[8738]: DD07D1612D1: from=<, size=2268, nrcpt=1 (queue active) Oct 6 14:55:18 test postfix/qmgr[8738]: DC1131612CC: removed Oct 6 14:55:18 test postfix/local[8773]: DD07D1612D1: [email protected], relay=local, delay=0.03, delays=0/0/0/0.03, dsn=2.0.0, status=sent (delivered to command: /usr/bin/procmail-wrapper -o -a $DOMAIN -d $LOGNAME) Oct 6 14:55:18 test postfix/qmgr[8738]: DD07D1612D1: removed when I run mail [email protected] the message is sent and received perfectly fine. I'm a bit of a noob when it comes to servers, but I pick things up fairly quickly, so please excuse any incorrect terminology and my general noobiness. Any help would be greatly appreciated, I've been googling for quite a while but I haven't found a solution yet, I'll add a copy of my main.cf file in a response below cheers guys here is the reformatted postconf, do you want the reformatted main.cf file too, or is this enough? alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 home_mailbox = Maildir/ html_directory = no mailbox_command = /usr/bin/procmail-wrapper -o -a $DOMAIN -d $LOGNAME mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man myhostname = server.test.com newaliases_path = /usr/bin/newaliases.postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sender_bcc_maps = hash:/etc/postfix/bcc sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous unknown_local_recipient_reject_code = 550 virtual_alias_maps = hash:/etc/postfix/virtual

  Read the article

• PHP versions warning on Plesk 11.0.9 upgrade on CentOS server

  - by Pixman

  I have a server turning on Plesk 10.4.4 and I want to upgrade it to 11.0.9. When I use the online upgrade tool, I have this warning: Parallels Panel pre-upgrade check... WARNING: You have a mixed set of 'php' and 'php53' packages installed. Installation or upgrade may fail or produce unexpected results. To resolve this issue run "sed -i.bak -e '/^\s*skip-bdb\s*$/d' /etc/my.cnf ; yum update 'php*' 'mysql*'". PHP Warning: Directive 'safe_mode' is deprecated in PHP 5.3 and greater in Unknown on line 0 I have run the code in ssh, but nothing changes. I have already searched all package names with "php", and I have this list: # yum list installed | grep php php-common.i386 5.3.13-5.el5.art installed php-pear.noarch 1:1.4.9-8.el5 installed php5-ioncube-loader.i386 4.0.7-11062118 installed php53.i386 5.3.3-13.el5_8 installed php53-cli.i386 5.3.3-13.el5_8 installed php53-devel.i386 5.3.3-13.el5_8 installed php53-gd.i386 5.3.3-13.el5_8 installed php53-imap.i386 5.3.3-13.el5_8 installed php53-mbstring.i386 5.3.3-13.el5_8 installed php53-mcrypt.i386 5.3.3-1.el5 installed php53-mysql.i386 5.3.3-13.el5_8 installed php53-pdo.i386 5.3.3-13.el5_8 installed php53-sqlite2.i386 5.3.2-11041315 installed php53-xml.i386 5.3.3-13.el5_8 installed psa-appvault-phpads.noarch 2.0.8-8203520080409011611 installed psa-appvault-phpbb.noarch 3.0.0-8200820080409011626 installed psa-appvault-phpbook.noarch 1.50-8203220080409011638 installed psa-appvault-phpbugtracker.noarch 1.19-8203820080416050605 installed psa-appvault-phpdig.noarch 1.85-8203120080409011645 installed psa-appvault-phpmoney.noarch 1.3-8204320080409011649 installed psa-appvault-phpmyfamily.noarch 1.4.1-8203420080409011655 installed psa-appvault-phpmyvisites.noarch 2.3-8202820080409011701 installed psa-appvault-phprojekt.noarch 5.2-8200820080409011713 installed psa-appvault-phpsurveyor.noarch 0.98-8204320080409011723 installed psa-appvault-phpwebsite.noarch 0.10.2-8203420080409011738 installed psa-appvault-phpwiki.noarch 1.3.11-8204320080409011808 installed psa-php53-configurator.i386 1.6.1-cos5.build1013111101.14 installed After verification in the Plesk file: panel_preupgrade_checker.php I think the warning is due to these lines: (from : panel_preupgrade_checker.php) foreach ($packages as $package) { $name = $package['name']; $hasPhp5 |= ($name == 'php' || strpos($name, 'php-') === 0); $hasPhp53 |= (strpos($name, 'php53') === 0); } Now, I think the problem is just due to the names of theses packages: php-common.i386 5.3.13-5.el5.art installed php-pear.noarch 1:1.4.9-8.el5 installed Can you help me to resolve this situation?

  Read the article

• Trouble creating FTP in Server 2008

  - by Saariko

  I have been trying to create an FTP server on my new Server 2008. I have been following both (very detailed and highly published here guides) For setting up using IIS Manager http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/ and For anonymous FTP http://www.trainsignaltraining.com/windows-server-2008-ftp-iis7 I am able to log as an anonymous user. My need is to use a named user, so I need to use the IIS Manager. I get error 530 when trying to log as a user. Connected to 127.0.0.1. 220 Microsoft FTP Service User (127.0.0.1:(none)): ftpmanager 331 Password required for ftpmanager. Password: 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: Filename: Error: 530 End Login failed. ftp> I can not learn from this message anything. My password is set to: 1234 (so I don't think I make a mistake here - testing purposes only ofc) Thank you. Note - I went over other posts on SE that I read, and couldn't get the result: IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in. FTP Error 530, User cannot log in, home directory inaccessible. Having trouble setting up FTP server on Windows Server 2008 EDIT I think I found some errors with the physical path. Going to Basic settings, and Test Connection on the physical path, gave me the following error: The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again. I am not sure which/whom should get access to the Root folder !? I want to point out, I managed to login with a domain user (change authorization and authentication methods) but this is NOT the requested solution. I checked to make sure that the FTP, folders, access is working properly. I am bit lost here. ==== More tries: I have enabled another Allow rule for ALL Users. I still get the same error. It seems that it doesn't matter if i use a correct or wrong password, I still get Error 530.

  Read the article

• PHP 5.2 to 5.3 not upgrading, no errors

  - by Webnet

  I'm following this guide: http://atik97.wordpress.com/2010/06/12/how-to-upgrade-to-php-5-3-in-ubuntu-9-10/ I've done all the steps, but it's still showing php 5.2.6 - any ideas? I have also tried -cgi instead of -cli, neither have any effect. update I've tried rebooting the server to see if that would have any effect and unfortunately it didn't update Output of dpkg -l *php*: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err: uppercase=bad) ||/ Name Version Description +++-=============================================-=============================================-========================================================================================================== un libapache2-mod-php4 <none> (no description available) ii libapache2-mod-php5 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (Apache 2 module) un libapache2-mod-php5filter <none> (no description available) ii php-pear 5.2.6.dfsg.1-3ubuntu4.6 PEAR - PHP Extension and Application Repository un php4-cli <none> (no description available) un php4-dev <none> (no description available) un php4-mysql <none> (no description available) un php4-pear <none> (no description available) ii php5 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.2.6.dfsg.1-3ubuntu4.6 command-line interpreter for the php5 scripting language ii php5-common 5.2.6.dfsg.1-3ubuntu4.6 Common files for packages built from the php5 source ii php5-curl 5.2.6.dfsg.1-3ubuntu4.6 CURL module for php5 un php5-dev <none> (no description available) ii php5-gd 5.2.6.dfsg.1-3ubuntu4.6 GD module for php5 ii php5-imap 5.2.6-0ubuntu5.1 IMAP module for php5 un php5-json <none> (no description available) ii php5-mcrypt 5.2.6-0ubuntu2 MCrypt module for php5 ii php5-mysql 5.2.6.dfsg.1-3ubuntu4.6 MySQL module for php5 un php5-mysqli <none> (no description available) ii php5-xsl 5.2.6.dfsg.1-3ubuntu4.6 XSL module for php5 un phpapi-20060613+lfs <none> (no description available) ii phpmyadmin 4:3.1.2-1ubuntu0.2 MySQL web administration tool update The following commands and their outputs: grep php53 /etc/apt/sources.list deb http://php53.dotdeb.org stable all deb-src http://php53.dotdeb.org stable all apt-cache search -f "libapache2-mod-php5" http://pastebin.com/XNXdsXYC update I've updated the question with more details on installed packages.

  Read the article

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

< Previous Page | 189 190 191 192 193 194 195 196 197 198 199 200  | Next Page >