Search Results

Search found 22298 results on 892 pages for 'default'.

Page 197/892 | < Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >

  • Is it possible to get xRandR to see two separate outputs with the nvidia driver?

    - by rumtscho
    I have two monitors, which I have set up with nvidia-settings in Twinview. The result: When I want to do something in xRandR, it does not function. It doesn't report one output per video card head, but a single output mapped to the combined area of both monitors: rumtscho@bradbury:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 3840 x 1440, current 3840 x 1440, maximum 3840 x 1440 default connected 3840x1440+0+0 0mm x 0mm 3840x1440 50.0* Now I promised somebody to help test a driver. The developer is using an open source driver for Intel video cards, and his driver assumes that there is more than one xRandR output, each mapped to a monitor. So I tried rewriting my xorg.conf to somehow get two outputs to show up, but failed. Googling showed that people faced with the xRandR-nvidia problem either stopped using xRandR and achieved what they needed with nvidia-settings, or changed their driver to nouveau. The first is not going to help in my situation, and I am not willing to give up the proprietary driver, because Compiz won't work without it. So does anybody know a way to get nvidia to actually pass on information on outputs to xRandR?

    Read the article

  • remastering knoppix: which version and what method should i use

    - by Stan_
    I'd like to remaster knoppix (mainly add and configure some software). I downloaded newest version (KNOPPIX-ADRIANE_V6.2CD-2009-11-18-EN.iso) but later i read that it has some other window manager as default, not kde... and i want to have kde on my remaster. Is kde included on that iso but it's not default or it's not included at all? If it's not there what knoppix version should i get for my remaster? My other question... I've seen some remastering scripts (with menus, etc) on knoppix forums, do any of these works with version i have? Or with version i should have if i need kde?

    Read the article

  • Virtual hosting in Varnish with individual vcl files for configuration

    - by Michael Sørensen
    I wish to use varnish to put in front of an apache and a tomcat on the same server. Depending on the ip requested, it goes to a different backend. This works. Now for most of the sites the default varnish logic will work just fine. However for some specific sites I wish to use custom VCL code. I can test for host name and include config files for the specific domains, but this only works inside the individual methods recv etc. Is there a way to include a complete set of instructions, in one file, per domain, without having to manage separate files for subdomain_recv, subdomain_fetch etc? And preferably without running seperate instances of varnish. When I try to include a file on the "root level" of default.vcl, I get a compilation error. Best regards, Michael

    Read the article

  • Changing Admin Site URL (actually port) - how?

    - by TomTom
    I have a new install of the band new SharePoint 2010. I use host header identified site collections for everything. By default the admin site is on a random port. I would like to move the admin site to port 80, for the server name. As all sites have coded names (for example "intranet", "projects") this would allow administration via the server name - which is easier as external access does not have to remember the port number. How do I do this? I already changed the default URL, but the site (application) is still wrongly mapped. I dont find anything to change the IIS settings in the admin site. I possibly just miss it - so can anyone point me in the right direction?

    Read the article

  • Implementing new required feature after software release

    - by TiagoBrenck
    Fake Scenario There is a software that was released 1 year ago. The software is to map and register all kind of animals on our planet. When the software was released, the client only needed to know the scientific name of the animal, a flag if it is in risk of extinction and a scale of dangerous(that is a fake software and specification, I don't want to discuss this here). There are already 100.000 animals records saved on DB. New Feature One year later, the client wants a new feature. It is really important to him to know the animals classes, and this is a required field. So he asks me to put a field to input the animal class, and this field is required. Or maybe where this animal was discovered. Problem I have already 100.000 recorded animals without a class or where it was discovered, but I need to insert a new column to storage this information and this column can't be null. I don't have a default value for this situation (there isn't a default animal class or where it was discovered). I don't want to keep the requirement rule only on my software, my DB must have this requirement too(I like to keep business rules on DB too). What are the alternatives to solve this situation? I am on a situation that this new feature cannot be previewed or reviewed for the existing records. The time already passed and I can't go back on time to get it

    Read the article

  • ASP.NET directories blocked from VisualSVN Server behind reverse proxy in IIS 6

    - by user143344
    I’ve got VisualSVN Server running behind a reverse proxy in IIS 6, Windows Server 2003. This isn’t ideal, but for the main web app on the server I’ve only got one IP address and SSL certificate available. Everything works except for when trying to commit to or browse the default ASP.NET directories (App_Browsers, App_Code, App_Data). SVN commits fail for these directories – which I believe is because IIS will never serve them by default. The reverse proxy uses a virtual directory in IIS – is there a change I can make in the web.config for this virtual directory to get around the issue?

    Read the article

  • FeedValidator & Feedburner get 404 when accessing wordpress RSS feeds when permalinks are enabled.

    - by Wazbaur
    I'm helping a friend set up a self-hosted Wordpress blog + feedburner and I'm seeing a problem with the feeds that I'm finding somewhat mysterious. Using the default permalink structure (e.g., ?p=123) everything works as expected; I can follow the feed in Google reader, navigate to it manually, and set it up in feedburner. However, once I switch away from the default permalink structure, feedburner and feedvalidator both report that accessing the feed is returning HTTP-404 and Google reader no longer shows new posts (I'm assuming for the same reason), but I can navigate to the feed using a browser. When I do that it appears as though nothing is wrong; there is a feed there and it contains all the posts I expect it to have. I've re-started the feedburner & reader set-up from the beginning after changing the link structure, so I don't think they're doing anything silly like looking at the feed at its old address. I've seen people with similar problems in various other places but there doesn't seem to be a good answer anywhere.

    Read the article

  • Start vino-server (VNC) before login on Linux CentOS

    - by Dr. Gianluigi Zane Zanettini
    I'm using the default vino-server package to access my CentOS 6 workstation via VNC. It works ok, but only AFTER I locally login on the workstation. I need to have vino-server start BEFORE the login, right at the Gnome login screen where I choose username and password. Due to personal reasons, I need to use Vino and not vnc-server or any other packages. I already tried to insert /usr/libexec/vino-server & in /etc/gdm/Init/Default but this didn't solve the issue.

    Read the article

  • WebSVN accept untrusted HTTPS certificate

    - by Laurent
    I am using websvn with a remote repository. This repository uses https protocol. After having configured websvn I get on the websvn webpage: svn --non-interactive --config-dir /tmp list --xml --username '***' --password '***' 'https://scm.gforge.....' OPTIONS of 'https://scm.gforge.....': Server certificate verification failed: issuer is not trusted I don't know how to indicate to websvn to execute svn command in order to accept and to store the certificate. Does someone knows how to do it? UPDATE: It works! In order to have something which is well organized I have updated the WebSVN config file to relocate the subversion config directory to /etc/subversion which is the default path for debian: $config->setSvnConfigDir('/etc/subversion'); In /etc/subversion/servers I have created a group and associated the certificate to trust: [groups] my_repo = my.repo.url.to.trust [global] ssl-trust-default-ca = true store-plaintext-passwords = no [my_repo] ssl-authority-files = /etc/apache2/ssl/my.repo.url.to.trust.crt

    Read the article

  • Why don't languages use explicit fall-through on switch statements?

    - by zzzzBov
    I was reading Why do we have to use break in switch?, and it led me to wonder why implicit fall-through is allowed in some languages (such as PHP and JavaScript), while there is no support (AFAIK) for explicit fall-through. It's not like a new keyword would need to be created, as continue would be perfectly appropriate, and would solve any issues of ambiguity for whether the author meant for a case to fall through. The currently supported form is: switch (s) { case 1: ... break; case 2: ... //ambiguous, was break forgotten? case 3: ... break; default: ... break; } Whereas it would make sense for it to be written as: switch (s) { case 1: ... break; case 2: ... continue; //unambiguous, the author was explicit case 3: ... break; default: ... break; } For purposes of this question lets ignore the issue of whether or not fall-throughs are a good coding style. Are there any languages that exist that allow fall-through and have made it explicit? Are there any historical reasons that switch allows for implicit fall-through instead of explicit?

    Read the article

  • 1080p Screen resolution problem after 10.04 to 12.04 update

    - by Ale
    I have a Samsung LCD 40" with a NVidia GeForce 6150SE nForce 430 Card. I recently upgraded from 10.04 to 12.04 and the best resolution I can get is 1360x768. I've tried the propietary drivers available on the repository kmod:nvidia_current kmod:nvidia_173_updates kmod:nvidia_current_updates kmod:nvidia_96 kmod:nvidia_96_updates kmod:nvidia_173 I've also downloaded latest from NVidia's Web, version: 295.40. But still no luck. With Nouveau driver, I can only get 1024x768. I know there is no problem with my hardware (video card, cable and monitor), I was using it perfectly on 10.04. Can anybody suggest something else I could try, to get my 1920x1080 resolution back? Thanks in advance. Here are some more information, that I got reading other similar posts on askubuntu. $ lspci | grep VGA 00:0d.0 VGA compatible controller: NVIDIA Corporation C61 [GeForce 6150SE nForce 430] (rev a2) $ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 240, current 1360 x 768, maximum 1360 x 768 default connected 1360x768 0 0 0mm x 0mm 1360x768 50.0 52.0* 1024x768 51.0 800x600 53.0 54.0 55.0 680x384 56.0 57.0 640x480 58.0 576x432 59.0 512x384 60.0 400x300 61.0 62.0 63.0 320x240 64.0

    Read the article

  • Custom distro using ubuntu 12.04

    - by user89707
    I am creating the custom operating system using the ubuntu 12.04. When ubuntu login from the light dm -- it shows ubuntu desktop . i need to change to the my os name. I need to replace the ambaince dark icon to fs icon by default for all the login and live cd. How to permanentely change the os name It should not change even the customer update the operating system too. I am using the remastersys. I am looking to develop the new distro. like mint ,, If i had an breif explanation of the creation of the repository and maintaining the updates . it will be more helpfull. Kindly provind the link for creating the full fledged os based on the ubuntu .. like mint, Snowlinux, etc did.. replace the grub with burg for default installation If remastersys is not good . then provide me some other tool to create . I am not having the high speed internet

    Read the article

  • Routing between two VLANs on Single Dell 6200 Switch

    - by jenglee
    I want to be able to route between two vlans that I have created and I am not sure how to go about it. So I have created, VLAN 5 with IP Address 192.168.5.1/24 and VLAN 10 with IP Address 192.168.0.1/24 //main IP addresses that I use. How would I be able to get (for example) the IP Address 192.168.0.144 to see any ip addresses in 192.168.5.1/24? Also do you have to set a default gateway for each VLAN or do you set the default gateway for the switch.

    Read the article

  • Prevalence of WMI enabled in real Windows Server networks

    - by TripleAntigen
    Hi I would like to get opinions from systems administrators, on how common it is that WMI functionality is actually enabled in corporate networks. I am writing an enterprise network application that could benefit from the features of WMI, but I noted after creating a virtual network based on Server 2008 R2, that WMI seems to be disabled by default. Do systems admins in practical corporate networks enable WMI? Or is it usually disabled for security purposes? What is it used for if it is enabled? Thanks for any advice! MORE INFO: I should have said, I really need to be able to query the workstations but I understand that by default the WMI ports on Win7 and XP firewalls (at least) are disallowed, so do you use some sort of group policy or other method to leave a hole open for WMI on the workstations? Or is just the servers that are of interest? Thanks for the responses!!

    Read the article

  • Virtualizing Firewalls/UTM

    - by TheD
    So Sophos UTM (Astaro Gateway UTM) can be virtualized in Hyper-V, VMWare, vSphere etc. Now I'm new to virtualization, so am wondering how the networking would be configured in this situation. Imagine the following (a very simple setup). A Zyxel router acting as the default gateway, standard ADSL line. This is connected directly via Ethernet to my VHost, Hyper-V in my case. Now I assume I need two virtual network adapters, one which is the "External" interface to the firewall, and the other being the "Internal" interface. But where does my switch go, since I have 5 machines (or X number of machines). Where is the switch connected, to the internal interface on the VHost? What default gateway do my clients use etc? How would the routing work if these two interfaces weren't bridged since they are virtual networks anyway. I'm a little confused! Any advice is much appreciated! Cheers

    Read the article

  • How to Configure Different Gateways for Different VLANs

    - by Bryan
    I have around 10 VLANs, and two different internet gateways. I want traffic on some VLANs to use one gateway, and traffic on other VLANs to use another gateway. (e.g. I wish to route server traffic via one gateway and desktop internet traffic down another). Is it possible to configure different default routes for different VLANs on a Dell 6224 switch? Or is their a better way of doing what I'm trying to achieve? The core switch I am using is a Dell PowerConnect 6224 switch. Currently I'm using: ip route 0.0.0.0 0.0.0.0 10.58.3.16 which creates the default gateway for all VLANs. I did consider adding multiple routes with equal metric, and setting ACLs between the VLANs to deny access to the 'wrong' gateway, but that idea just doesn't feel right to me.

    Read the article

  • receiving "command not found" error messages after fresh reinstall of Lubuntu 14.04

    - by user236378
    Lubuntu 14.04 was working really great. . .until I messed up and had to do a complete fresh reinstall. Now I receive error messages when I input commands into the Terminal, even after immediately completing the fresh install. For example I type: sudo leafpad ?/etc/default/ or sudo leafpad ?/etc/default/grub I get: sudo: leafpad: command not found I type: sudo update-initramfs ?-u or sudo update-grub I get: sudo: update-initramfs: command not found or sudo: update-grub: command not found If I use the command mkdir I get: mkdir: command not found I also get this same exact error message, command not found, with sudo apt-get and wget In other words I can't do anything that I was able to do when inputting commands into the terminal. So I cannot add any repositories or update anything at all. I am not really sure what is causing the problem(s). It appeared to me that Lubuntu installed and booted up OK. However just as soon as I enter anything into the Terminal I immediately get the above error messages. I have tried to do the reinstall three times, same error messages. If anyone can suggest any fixes I would really appreciate it very much. Thank you!

    Read the article

  • Using PVLANs with normal VLANs in a trunked environment

    - by user974896
    Assume a trunked environment with two switches, S1 and S2. The swtiches are connected with a trunk port designed to pass VLAN 26. What would happen if VLAN 26 on S2 is configured as a private-vlan with the default gateway and DHCP server and default gateway as promisc ports. What if S1's VLAN 26 is configured as a standard VLAN. Would the hosts on S1 be able to communicate with the promisc ports on S2? Would they be able to communicate with the hosts on S2? To further complicate things what if the DHCP server were to reside on S1 and I wanted S2 to have private VLANS with promisc ports as the gateway and DHCP server while still leaving S1 in a standard vlan configuration.

    Read the article

  • Custom grub config hangs at the prompt

    - by drecute
    Please I need help with this custom grub: default=0 timeout=20 fallback=1 title Remote Install root (hd0,0) kernel /vmlinuz_remote lang=en_US keymap=us ks=nfs:192.168.128.42:/tftpboot/Kickstart/ks.cfg ksdevice=00:1A:64:22:32:4B headless xfs panic=60 initrd /initrd_remote.img I have 3 grub configs and I've been able to make the "Remote install" grub config to be the default run. At the moment it boots up but hangs at the prompt. Grub version: 0.98 The other 2 grubs that comes that exists after successful installation and update of the kernel are: splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-279.9.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-279.9.1.el6.x86_64 ro root=/dev/mapper/vg_serverprisa-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_LVM_LV=vg_serverprisa/lv_swap rd_NO_MD rd_LVM_LV=vg_serverprisa/lv_root SYSFONT=latarcyrheb-sun16 crashkernel=auto KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet initrd /initramfs-2.6.32-279.9.1.el6.x86_64.img title CentOS (2.6.32-279.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-279.el6.x86_64 ro root=/dev/mapper/vg_serverprisa-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_LVM_LV=vg_serverprisa/lv_swap rd_NO_MD rd_LVM_LV=vg_serverprisa/lv_root SYSFONT=latarcyrheb-sun16 crashkernel=auto KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet initrd /initramfs-2.6.32-279.el6.x86_64.img

    Read the article

  • mod_rewrite and SEO friendliness

    - by John Doe
    My website has an atypical structure and I'm not sure if this could create problems in the long run, specially for SEO positioning purposes. I have a unique, large PHP script, and I use the Apache module mod_rewrite in the .htaccess file to create friendly URLs, for example: RewriteRule ^$ /index.php?section=Main RewriteRule ^createArticle$ /index.php?section=Main&view=CreateArticle RewriteRule ^configuration$ /index.php?section=Configuration RewriteRule ^article/([0-9]{1,10})$ /index.php?section=Article&view=Default&id=$1 RewriteRule ^deleteArticle/([0-9]{1,10})$ /index.php?section=Article&view=Delete&id=$1 RewriteRule ^reportArticle/([0-9]{1,10})$ /index.php?section=Article&view=Report&id=$1 RewriteRule ^logIn$ /index.php?section=Authentication ... So, www.example.com/index.php?section=Article&view=Default&id=105 would become www.example.com/article/105. The only real physical file is index.php, in which the parameters of the URL queried is processed and the corresponding result is outputted. My question is, do the crawling robots (e.g. Googlebot) recognize these links? Do they index the resulting HTML outputted by index.php with the specified parameters as if it was a actual HTML file? Also, would this become a problem when creating a Sitemap?

    Read the article

  • How do I open multiple windows when Outlook 2010 starts?

    - by Eric
    OS: Windows 7 64-bit App: Outlook 2010 32-bit Server: Exchange 2010 I'd like to modify Outlook's default startup behavior so that it shows both my Inbox and Calendar when I click my shortcut. I use both of them all day, and know how to just right-click the calendar and select "Open in New Window." I run my inbox on one screen and my calendar on another. I also configured my calendar to be the folder that opens by default when I start Outlook so I don't miss early appointments, but if I could somehow have BOTH open in two separate windows, that would be awesome. Is there a command-line interface or something that can accomplish this? Thanks in advance.

    Read the article

  • can't send with postfix but I can whith one user

    - by CvR_XX
    I have a postfix and dovecot server but when i try to send an email i get an time -out. Im trying to send with the email [email protected]. A telnet session isn't helping much ether. I get a blank screen. Local it's working fine. My smtp service is running on treadity.com:25. The strange thing is that the logs are completely empty with any info regarding sending emails. Receiving is working alright. Another strange thing is that i've send some message's and that it worked. But that is only with one email. I can still send from that account but other emails are failing any idea's? config file: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters #smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem #smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key #smtpd_use_tls=yes #smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache #smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_tls_cert_file=/etc/ssl/certs/dovecot.pem smtpd_tls_key_file=/etc/ssl/private/dovecot.pem smtpd_use_tls=yes # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters #smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem #smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key #smtpd_use_tls=yes #smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache #smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_tls_cert_file=/etc/ssl/certs/dovecot.pem smtpd_tls_key_file=/etc/ssl/private/dovecot.pem smtpd_use_tls=yes # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters #smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem #smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key #smtpd_use_tls=yes #smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache #smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_tls_cert_file=/etc/ssl/certs/dovecot.pem smtpd_tls_key_file=/etc/ssl/private/dovecot.pem smtpd_use_tls=yes smtpd_tls_auth_only = yes #Enabling SMTP for authenticated users, and handing off authentication to Dovecot smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_auth_enable = yes 1,1 Top

    Read the article

  • How to display password policy information for a user (Ubuntu)?

    - by C.W.Holeman II
    Ubuntu Documentation Ubuntu 9.04 Ubuntu Server Guide Security User Management states that there is a default minimum password length for Ubuntu: By default, Ubuntu requires a minimum password length of 4 characters Is there a command for displaying the current password policies for a user (such as the chage command displays the password expiration information for a specific user)? > sudo chage -l SomeUserName Last password change : May 13, 2010 Password expires : never Password inactive : never Account expires : never Minimum number of days between password change : 0 Maximum number of days between password change : 99999 Number of days of warning before password expires : 7 This is rather than examining various places that control the policy and interpreting them since this process could contain errors. A command that reports the composed policy would be used to check the policy setting steps.

    Read the article

  • Mysql migrate huge db from innodb to ndbcluster Err: the table is full

    - by Nguyen Trong Nhan
    I'm trying to migrate old database to mysql cluster (4 data nodes) by using command: ALTER TABLE sample ENGINE=NDBCLUSTER but I'm getting the following error: The table '#sql-7ff3_3' is full There are approximately 300 mil rows in this table. Here are my config file: /mysql-cluster/config.ini [NDBD DEFAULT] NoOfReplicas=2 DataDir=/data/mysql-cluster/ndb/ BackupDataDir=/data/mysql-cluster/backup/ DataMemory=10G IndexMemory=5G TimeBetweenLocalCheckpoints=6 FragmentLogFileSize=256MB NoOfFragmentLogFiles=50 MaxNoOfOrderedIndexes=8000 MaxNoOfConcurrentOperations=100000 MaxNoOfTables = 10000 RedoBuffer=128M MaxNoOfAttributes=5000 MaxNoOfUniqueHashIndexes=1024 /etc/my.cnf [mysqld] basedir=/usr/local/mysql datadir=/data/mysql-cluster/mysqld/ event_scheduler=on default-storage-engine=ndbcluster ndbcluster ndb-connectstring=192.168.x.x,192.168.x.x innodb_file_per_table innodb_buffer_pool_size = 512MB key_buffer = 512M key_buffer_size = 512M sort_buffer_size = 512M table_cache = 1024 read_buffer_size = 512M

    Read the article

  • how to setup duel monitors an xorg.conf

    - by MrMonty
    # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" # Removed Option "Xinerama" "1" # Removed Option "Xinerama" "0" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" # Removed Option "TwinView" "1" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection thats my file!

    Read the article

< Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >