Search Results

Search found 2796 results on 112 pages for 'bounce rate'.

Page 2/112 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How can I fix my vista PCs screen resolution and refresh rate

  - by Antony Scott

  I have a media PC running media portal hooked up to my HDTV via HDMI. The TV is a couple of years old now, so only supports 1080i, which is 1920x1080@25Hz. I've got it connected to my PC via a HDMI compatible AV receiver. If I power up the amp (wait for it to boot fully) followed by the TV| and finally the PC, all is well and I get a picture. If I deviate from that sequence, or don't wait for the amp to book up fully, or even switch the amp to another video input (for example, my PS3). The PC sees this and defaults the screen resolution/refresh rate to 1920x1080@60Hz. So, I end up with a blank screen. To fix this I have to use UltraVNC from a PC and change the refresh rate back to 25Hz. So, is there a way to turn off that auto detection, or to manually define what resolution/refresh rates the monitor can do. I'm using the on-board Radeon 3200 video and do not have any of the AMD software installed as it seems to cause problems with video playback. So, I'm looking for a native vista fix, or possible some 3rd party software.

  Read the article

• Can't get decent refresh rate on crt connected to dvi

  - by Ernst

  Hi, I have a CRT connected to a dvi connector on a videocard using a vga cable and a dvi to vga adapter. Now I cannot set the refresh rate to anything decent (only 60Hz and lower). I've hat this happen using different CRT's, graphics cards (although all ATI, both agp and pcie), and operating systems (both linux and windows). Any idea on how to solve this, maybe some bios setting? Thanks

  Read the article

• jQuery Bounce ignores positioning

  - by ashansky

  I'm having a problem trying to use the jQuery effect "bounce" on an absolutely position div inside of a relatively positioned div. The #Bounce div is positioned to be slightly above the container div and when a certain message is received it is supposed to bounce on top of it. But what ends up happening is that the #bounce div drops down into the container div and bounces inside of it till it stops and then correctly repositions itself on top of the container div. This same code is working in Firefox but doesn't seem to be working in Webkit or IE. Can anyone help me understand why this is happening? if (jQuery("#Bounce").data("bouncing") == false || jQuery("#Bounce").data("bouncing") == undefined) { jQuery("#Bounce").show().effect("bounce",{times:10,distance:50},300,function(){jQuery("#Bounce").data("bouncing", false);}); jQuery("#Bounce").data("bouncing", true); } <div id="Container" style="height: 28px; float: right; position: relative; top: 2px; cursor: pointer; padding-top: 0px; padding-right: 0px; padding-bottom: 0px; padding-left: 3px; "> ... <div id="Bounce" style="bottom: 28px; right: 0px; height: 26px; width: 26px; z-index: 989; display: none; position: absolute; ">...</div> </div>

  Read the article

• Rate limiting a ruby file stream

  - by Matthew Savage

  I am working on a project which involves uploading flash video files to a S3 bucket from a number of geographically distributed nodes. The video files are about 2-3mb each, and we are only sending one file (per node) every ten minutes, however the bandwidth we consume needs to be rate limited to ~20k/s, as these nodes are delivering streaming media to a CDN, and due to the locations we are only able to get 512k max upload. I have been looking into the ASW-S3 gem and while it doesn't offer any kind of rate limiting I am aware that you can pass in a IO Stream. Given this I am wondering if it might be possible to create a rate-limited stream which overrides the read method, adds in the rate limiting logic (e.g. in its simplest form a call to sleep between reads) and then call out to the super of the overridden method. Another option I considered is hacking the code for Net::HTTP and putting the rate limiting into the send_request_with_body_stream method which is using a while loop, but I'm not entirely sure which would be the best option. I have attempted at extending the IO class, however that didn't work at all, simply inheriting from the class with class ThrottledIO < IO didn't do anything. Any suggestions will be greatly appreciated.

  Read the article

• Change the playback rate of a track in real time on Android

  - by android_dev

  Hello, I would like to know if somebody knows a library to changing the playback rate of a track in real time. My idea is to load a track and change its playback rate to half or double. Firstly, I tried with MusicPlayer but is was not possible at all and then I tried with SoundPool. The problem is that with SoundPool I can´t change the rate once the track is loaded. Here is the code I am using (proof of concept): float j = 1; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); Button b = (Button)findViewById(R.id.Button01); b.setOnClickListener(new OnClickListener() { @Override public void onClick(View v) { j = (float) (j +.5); } }); AssetFileDescriptor afd; try { SoundPool sp = new SoundPool(1, AudioManager.STREAM_MUSIC, 0); afd = getAssets().openFd("wav/sample.wav"); int id = sp.load(afd, 1); sp.play(id, 1, 1, 1, 0, j); } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } } When I press the button, the playback rate should increase but it does not happen. Any idea of how change the rate in real time? Thanks in advance.

  Read the article

• How to set the bounce address using System.Net.Mail?

  - by Anthony

  I'm trying to implement the Variable envelope return path (VERP) method to manage email addresses (ie when an email I send bounces back I want it to be sent to a specific email address so that I can update my database to avoid sending emails to that email address in the future). According to this article it is possible to specify the email address a bounce email is sent to. How do you do this in .Net? For example say I ([email protected]) want to send an email to you ([email protected]). If [email protected] doesn't exist anymore I want yourserver to send the bounce email to [email protected]). This way when I receive this bounced email I know that [email protected] is not a valid email address anymore and I can update my database accordingly. In this example, the bounce address would be: [email protected] How do you specify it using System.Net.Mail?

  Read the article

• How does google calculate bounce rate?

  - by Luticka

  Hello We run a website where we sell access to a member area. We use Google analytics to optimize the site but i have a bounce rate in about 85%. The problem is that I'm not sure what count as a bounce and whats not. If a person go to my front page and log in directly. Will this count as a bounce because there is no analytics on the member pages or is Google smart enough to see that the link is on my side? Thanks a lot.

  Read the article

• Sudden drop of pageviews/visit and increase of bounce rate in Analytics

  - by Tebb

  Google analytics stats: 04 june 2012 Visits: 4.423 Unique visitors: 3.558 Pageviews: 77.352 Pageviews / visit: 17,49 Visit length: 00:06:26 Bounce rate: 1,09% 05 june 2012 Visits: 4.652 Unique visitors: 3.825 Pageviews: 45.087 Pageviews / visit: 9,69 Visit length: 00:06:45 Bounce rate: 19,60% From one day to another the bounce rate went from 1% to 19%, the pageviews dropped by half so did the pageviews/visit. The only thing I changed (If I remember correctly) on the site, was an advertisment that used a javascript. Could this be the reason? and, if it is, how can I know which one is the real stats?

  Read the article

• How to handle the different frame rate on different devices?

  - by Fenwick

  I am not quite sure how frame per second works on a web page. I have a Canvas game that involves in moving an image from point A to B, and measuring the time elapsed. The code can be as simple as: var timeStamp = Date.now(); function update(){ obj.y += obj.speed; text = "Time: "+ (Date.now() - timeStamp) + "ms"; } The function update() is called every frame. The problem is that the time elapsed is different from device to device. It is pretty short on my PC, but get longer on my iPad, and is much longer on my cell phone. I thought it is because the FPS is smaller on mobile devices, so instead of calling update() every frame, I call it every 1ms by using a setInterval. But this does not solve the problem. In my understanding, the function for setInterval is invoked based on the increment in system time, other than frame rate, so it should fix the problem. Am I missing anything here? If the setInterval function is called based on FPS, is there any way to get around with the FPS difference across devices? On a side note, I have sort of a "water simulator" on the same canvas. It involves in redrawing about 60 objects which can be 600x600 pixels for every frame, so it could be a frame rate killer. I am using Phaser.js but not really using much of its functionalities, if that helps.

  Read the article

• How to disable all bounce back email in exim 4.69

  - by liame

  I have set up an email server to send out solicited newsletters. There should be no "regular" users of this server, so it is not desirable to send bounce notifications back to the recipient. Especially so since I am tracking bounces myself by parsing the log files periodically. What I want is to unconditionally prevent exim from ever sending a bounce notification email back to a sender. How can I do this? Thank you! (I accidentally posted this to superuser before posting it here, disregard that if you come across) What I want is an email server that will accept all incoming emails, deliver it accordingly (that is remotely or locally) and not send a bounce notification the sender upon bounce. I log bounces myself, in a database. The only function bounce messages have in my setting is to waste resources and bandwidth. I need to send emails fast, using exiwhat during a run, I see a significant number of deliveries to [email protected]. I could potentially increase my email productivity by 10~20% if all bounce emails are eliminated.

  Read the article

• Limit rate of outgoing UDP packets per second

  - by tim82

  Hi, since Teamspeak version 3 sends lots of packets per user and our provider is getting problems with his infrastructure above 20.000 packets per second we have to limit it that our servers are not going to be shut down. Red a lot about iptables but was not able to find the right rules. Could you give me an advise how to manage that the server is not going to send more than 19k packets per seconds? We are running on debian 4 Thanks in Advance Tim

  Read the article

• How can I "filter" postfix-generated bounce messages?

  - by Flimzy

  We are using postfix 2.7 and custom SMTPD (based on qpsmtpd) in highly customized configuration for spam filtering. We have a new requirement to filter postfix-generated bounces through our custom qpsmtpd process (not so much for content filtering, but to process these bounces accordingly). Our current configuration looks (in part) like this: main.cf (only customizations shown): 2526 inet n - - - 0 cleanup pickup fifo n - - 60 1 pickup -o content_filter=smtp:127.0.0.2 Our smtpd injects messages to postfix on port 2526, by speaking directly to the cleanup daemon. And the custom pickup command instructs postfix to hand off all locally-generated mail (from cron, nagios, or other custom scripts) to our custom smtpd. The problem is that this configuration does not affect postfix generated bounce messages, since they do not go through the pickup daemon. I have tried adding the same content_filter option to the bounce daemon commands, but it does not seem to have any effect: bounce unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 defer unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 trace unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 For reference, here is my main.cf file, as well: biff = no # TLS parameters smtpd_tls_loglevel = 0 smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${queue_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${queue_directory}/smtp_scache smtp_tls_security_level = may mydestination = $myhostname alias_maps = proxy:pgsql:/etc/postfix/dc-aliases.cf transport_maps = proxy:pgsql:/etc/postfix/dc-transport.cf # This is enforced on incoming mail by QPSMTPD, so this is simply # the upper possible bound (also enforced in defaults.pl) message_size_limit = 262144000 mailbox_size_limit = 0 # We do our own message expiration, but if we set this to 0, then postfix # will try each mail delivery only once, so instead we set it to 100 days # (which is the max postfix seems to support) maximal_queue_lifetime = 100d hash_queue_depth = 1 hash_queue_names = deferred, defer, hold I also tried adding the internal_mail_filter_classes option to main.cf, but also tono affect: internal_mail_filter_classes = bounce,notify I am open to any suggestions, including handling our current content-filtering-loop in a different way. If it's not clear what I'm asking, please let me know, and I can try to clarify.

  Read the article

• Making particle bounce off a line with friction

  - by Dlaor

  So I'm making a game and I need a particle to bounce off a line. I've got this so far: public static Vector2f Reflect(this Vector2f vec, Vector2f axis) //vec is velocity { Vector2f result = vec - 2f * axis * axis.Dot(vec); return result; } Which works fine, but then I decided I wanted to be able to change the bounciness and friction of the bounce. I got bounciness down... public static Vector2f Reflect(this Vector2f vec, Vector2f axis, float bounciness) //Bounciness goes from 0 to 1, 0 being not bouncy and 1 being perfectly bouncy { var reflect = (1 + bounciness); //2f Vector2f result = vec - reflect * axis * axis.Dot(vec); return result; } But when I tried to add friction, everything went to hell and back... public static Vector2f Reflect(this Vector2f vec, Vector2f axis, float bounciness, float friction) //Does not work at all! { var reflect = (1 + bounciness); //2f Vector2f subtract = reflect * axis * axis.Dot(vec); Vector2f subtract2 = axis * axis.Dot(vec); Vector2f result = vec - subtract; result -= axis.PerpendicularLeft() * subtract2.Length() * friction; return result; } Any physics guys willing to help me out with this? (if you're not sure what I mean with the friction of a bounce see this: http://www.metanetsoftware.com/technique/diagrams/A-1_particle_collision.swf)

  Read the article

• How to rate-limit in nginx, but including/excluding certain IP addresses?

  - by Jason Cohen

  I'm able to use limit_req to rate-limit all requests to my server. However I'd like to remove the rate restriction for certain IP addresses (i.e. whitelist) and use a different rate restriction for certain others (i.e. certain IPs I'd like as low as 1r/s). I tried using conditionals (e.g. if ( $remote_addr = "1.2.3.4" ) {}) but that seems to work only with rewrite rules, not for rate-limit rules.

  Read the article

• How to accurately parse smtp message status code (DSN)?

  - by Geo

  RFC1893 claims that status codes will come in the format below you can read more here. But our bounce management system is having a hard time parsing error status code from bounce messages. We are able to get the raw message, but depending on the email server the code will come in different places. Is there any rule on how to parse this type of messages to obtain better results. We are not looking for the 100% solution but at least 80%. This document defines a new set of status codes to report mail system conditions. These status codes are intended to be used for media and language independent status reporting. They are not intended for system specific diagnostics. The syntax of the new status codes is defined as: status-code = class "." subject "." detail class = "2"/"4"/"5" subject = 1*3digit detail = 1*3digit White-space characters and comments are NOT allowed within a status- code. Each numeric sub-code within the status-code MUST be expressed without leading zero digits. The quote above from the RFC tells one thing but then the text below from a leading tool on bounce management says something different, where I can get a good source of standard status codes: Return Code Description 0 UNDETERMINED - (ie. Recipient Reply) 10 HARD BOUNCE - (ie. User Unknown) 20 SOFT BOUNCE - General 21 SOFT BOUNCE - Dns Failure 22 SOFT BOUNCE - Mailbox Full 23 SOFT BOUNCE - Message Too Large 30 BOUNCE - NO EMAIL ADDRESS. VERY RARE! 40 GENERAL BOUNCE 50 MAIL BLOCK - General 51 MAIL BLOCK - Known Spammer 52 MAIL BLOCK - Spam Detected 53 MAIL BLOCK - Attachment Detected 54 MAIL BLOCK - Relay Denied 60 AUTO REPLY - (ie. Out Of Office) 70 TRANSIENT BOUNCE 80 SUBSCRIBE Request 90 UNSUBSCRIBE/REMOVE Request 100 CHALLENGE-RESPONSE

  Read the article

• flat-rate backup service for Windows Server

  - by Colin Pickard

  Hi, Does anyone know if there is a decent flat-rate backup service which supports Windows Server? I've investigated the following: Backblaze - no WS support, sales say they have a "no server" policy JungleDisk - not flat rate Mozy - no WS on regular edition, no flat-rate on Pro edition Dropbox - no flat rate Carbonite - technically flat rate, but throttles uploads to modem speeds EDIT: Very similar question: Is there a decent flat-rate online backup solution for Linux machines?

  Read the article

• Frame rate on one of two machines running same code seems to be capped at 60 for no reason

  - by dennmat

  ISSUE I recently moved a project from my laptop to my desktop(machine info below). On my laptop the exact same code displays the fps(and ms/f) correctly. On my desktop it does not. What I mean by this is on the laptop it will display 300 fps(for example) where on my desktop it will show only up to 60. If I add 100 objects to the game on the laptop I'll see my frame rate drop accordingly; the same test on the desktop results in no change and the frames stay at 60. It takes a lot(~300) entities before I'll see a frame drop on the desktop, then it will descend. It seems as though its "theoretical" frames would be 400 or 500 but will never actually get to that and only do 60 until there's too much to handle at 60. This 60 frame cap is coming from no where. I'm not doing any frame limiting myself. It seems like something external is limiting my loop iterations on the desktop, but for the last couple days I've been scratching my head trying to figure out how to debug this. SETUPS Desktop: Visual Studio Express 2012 Windows 7 Ultimate 64-bit Laptop: Visual Studio Express 2010 Windows 7 Ultimate 64-bit The libraries(allegro, box2d) are the same versions on both setups. CODE Main Loop: while(!abort) { frameTime = al_get_time(); if (frameTime - lastTime >= 1.0) { lastFps = fps/(frameTime - lastTime); lastTime = frameTime; avgMspf = cumMspf/fps; cumMspf = 0.0; fps = 0; } /** DRAWING/UPDATE CODE **/ fps++; cumMspf += al_get_time() - frameTime; } Note: There is no blocking code in the loop at any point. Where I'm at My understanding of al_get_time() is that it can return different resolutions depending on the system. However the resolution is never worse than seconds, and the double is represented as [seconds].[finer-resolution] and seeing as I'm only checking for a whole second al_get_time() shouldn't be responsible. My project settings and compiler options are the same. And I promise its the same code on both machines. My googling really didn't help me much, and although technically it's not that big of a deal. I'd really like to figure this out or perhaps have it explained, whichever comes first. Even just an idea of how to go about figuring out possible causes, because I'm out of ideas. Any help at all is greatly appreciated.

  Read the article

• Wireless iwconfig rate auto too low

  - by Jamie Kitson

  Hi, left to its own devices my wireless connects at too low a speed. I have a 20meg internet connection and my wireless is slowing it down to like 3meg. When I reboot into windows it's fine. When I run iwconfig eth1 rate 24M or even 48M the connection is much faster and runs fine, why won't it automatically go higher? Is this the fault of the driver? I am running Broadcom's driver compiled from source. Would adding iwconfig eth1 rate 24M to rc.local be the right way to force it at boot? Output from iwconfig when rate=auto: eth1 IEEE 802.11 ESSID:"honeypot" Mode:Managed Frequency:2.417 GHz Access Point: xxx Bit Rate=1 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=5/5 Signal level=-47 dBm Noise level=-91 dBm Rx invalid nwid:0 Rx invalid crypt:2 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Thanks, Jamie

  Read the article

• Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

  - by Paul H

  I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

  Read the article

• twitter api post rate limit

  - by Xavier

  Does anyone know Twitter's rate limit on posting? Looking at their web page they claimed to not have one but I get an exception thrown if my program posts too fast... Any help is appreciated.

  Read the article

• Force startx to run X in a specific resolution and refresh Rate

  - by Z9iT

  From my past experience (using Win-Xp), this particular monitor works only on 60Hz , Best resolution being 1024x768. I have "installed and configured" Ubuntu 12.04 Minimal (on USB stick) so that most of the time terminal is used, however, whenever there is a need to enter GUI, I may issue startx command to go into gnome. However the problem is that on this particular system, issuing this command poses problem because its default refresh rate won't synchronize with the monitor. The display keep on flickering and utterly unreadable. It is visible that gnome has been loaded and default wallpaper and desktop items are visible. But the problem is due to refresh rate different than 60Hz. I am looking for a command attribute to startx command which will force the refresh rate to 60Hz and resolution preferably to 1204x768 I can open terminals with Ctrl+Alt+T and enter commands. Key combinations like Ctrl+Alt+NumPlus works flawlessly in distributions like solaris, but it's not working for me. Also the commands like xrandr -r 60 60 being refresh rate wont work. The same problem is faced even when I boot from a live CD

  Read the article

• System reverts to 87Hz refresh rate at every startup after I have installed nvidia drivers

  - by Mohammad Kamil Nadeem

  Every time the system starts the screen's refresh rate reverts to 87Hz which results in a pixelated and flickery screen which I have to manually correct every time by either selecting 60Hz as my refresh rate. I have tried "save to X configuration files" and even tried by making the changes as Root but to no avail as it again reverts to 87Hz on every system startup The Open Source Drivers are Okay for regular Unity but many games don't work on it hence I had to install the nvidia drivers. I have been facing this since the Beta Phase although this is on a fresh installation of 12.04 final release. I am also providing my Xorg.conf file just in case it might help http://paste.ubuntu.com/952196/ Also for some reason Displays shows my CRT monitor as Laptop but on open source drivers it was mentioning it as a 14" CRT only This bug is also present on Edubuntu 12.04 This is not present on Xubuntu 12.04 I had selected to install updates and 3rd party software on the install and was greeted with a correct refresh rate screen on the Boot Up. I like Xubuntu.

  Read the article

• Expected sprint completion rate and load in scrum?

  - by bjarkef

  Recently at work there have been increased focus on completion rate and load on the developers in our sprints. With completion rate I mean, if we plan 20 user stories for a sprint, what percentage of these user stories are closed at the end of the sprint. And with load I mean, if we have a sprint with 3 developers of 60 hours each, i.e. 180 hours for the sprint, how many hours worth of user stories do we schedule for the sprint. So I am really interested in others experience with this, I guess this is something everybody working with scrum deals with. My question is, what completion rate and load are expected/usual, and how are your team doing with respect to these parameters?

  Read the article

• Contracting rate for Android development

  - by Robottinosino

  I am a developer, maybe I have a project to work on, not sure how much to "charge" for my work.... Help me find the price? Looking for an contracting rate interval, expressed in EUR, to offer for an Android development gig. Location: Europe, off-site (telecommuting) Environment: Android + HTTP back-end Length of project: 1 month Rate currency: EUR Rate measure: daily or hourly Other skills required: UI design, basic J2EE, web services Client profile: medium business (100+ employees) Previous published apps: 1, on G-Play Design work: partially already done, data flow is established, data models to be built Required graphics/multimedia elements: provided by the client Source control: remove over SSH Team size: one person in development, others (unknown) for marketing, copy, etc. Risk factor: medium Client reputation: modest but established Potential for continued work: absent (for now) Internationalisation/localisation: no Native code (C/C++,...): none, only Android SDK, pure Java Working culture: (based on initial discussion) - high pressure Other projects in the pipe: zero Opportunity to learn from the project or build new skills: 5% Negotiating experience: good Cost of accessories: (licenses, device to debug on) zero If I need to be more precise, please just say how and I will be.

  Read the article

• How do you answer "Rate yourself" questions?

  - by Vinoth Kumar

  Hi , I have been frequently asked questions like "Rate yourself in java" It goes like interviewer : Rate yourself in java on the scale of 10 me: 9 interviewer : Rate yourself in J2EE me : 8 .... But really I just come up with arbitrary numbers. Sure I know Java well , but what does it mean to say "9 out of 10" . I think it is a very subjective question, that does not make sense overall. The problem is ,if I say 9 , If I am not able to answer any question , the interviewer might think , "this guy just said 9" . On the other hand If I said 6 , there is a good chance the interviewer might think "He rates himself this low...not good" How do you respond to such questions ?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >