Search Results

Search found 7371 results on 295 pages for 'raid card'.

Page 2/295 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• SD Card Reader not working in Ubuntu 12.04

  - by tripkane

  I have a read many other posts on this issue and believe that Ubuntu 12.04 is not even recognizing my SD Card Reader as just that: Computer Model: Metabox (Australian builder of Clevo laptops) / Clevo P150EM OS: Ubuntu 12.04 (64 Bit) CPU: Intel(R) Core(TM) i7-3720QM CPU @ 2.60GHz HD: 120GB Intel 550/520MB/s SSD According to the people who built my computer, the specs of the SD Card reader in my comp are as follows: Manufacture: Realtek Semiconduct Corp. Location: PCI bus 3 Hardware ID: PCI\Ven_10EC&DEV_5289&SUBSYS_51051558 Physical device object name: \Device\NTPNP_PCI0015 Here are the relevant outputs of the following commands run from the terminal: sudo lshw *-generic UNCLAIMED description: Unassigned class product: Realtek Semiconductor Co., Ltd. vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list configuration: latency=0 resources: memory:f6a00000-f6a0ffff sudo lspci -v -nn 03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device [10ec:5289] (rev 01) Subsystem: CLEVO/KAPOK Computer Device [1558:5105] Flags: bus master, fast devsel, latency 0, IRQ 4 Memory at f6a00000 (32-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [b0] MSI-X: Enable- Count=1 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Does the unassigned details of these outputs mean that Ubunutu desn't know that the SD Card Reader is one and what do with it? and if so how should I go about fixing it?? Cheers ;)

  Read the article

• Zero-channel RAID for High Performance MySQL Server (IBM ServeRAID 8k) : Any Experience/Recommendati

  - by prs563

  We are getting this IBM rack mount server and it has this IBM ServeRAID8k storage controller with Zero-Channel RAID and 256MB battery backed cache. It can support RAID 10 which we need for our high performance MySQL server which will have 4 x 15000K RPM 300GB SAS HDD. This is mission-critical and we want as much bandwidth and performance. Is this a good card or should we replace with another IBM RAID card? IBM ServeRAID 8k SAS Controller option provides 256 MB of battery backed 533 MHz DDR2 standard power memory in a fixed mounting arrangement. The device attaches directly to IBM planar which can provide full RAID capability. Manufacturer IBM Manufacturer Part # 25R8064 Cost Central Item # 10025907 Product Description IBM ServeRAID 8k SAS - Storage controller (zero-channel RAID) - RAID 0, 1, 5, 6, 10, 1E Device Type Storage controller (zero-channel RAID) - plug-in module Buffer Size 256 MB Supported Devices Disk array (RAID) Max Storage Devices Qty 8 RAID Level RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 1E Manufacturer Warranty 1 year warranty

  Read the article

• What is the best way to create RAID 1?

  - by user3125731

  I'm looking for a way to create the RAID 1 array without losing my data on CentOS. Here's my situation: I've got a web server running on CentOS. There is one VG partition with few LV volumes. I bought a second HDD (the same model and size as the first one) and I want to create the RAID 1 configuration. I can't just shut down this server for more than an hour because my clients will be disappointed. I need to do this as quickly as possible with minimal risk of data loss.

  Read the article

• Implementing RAID 1 in Ubuntu 10.04 Desktop [closed]

  - by Dibyendra

  I found many resources on implementing RAID 1 using two disk drives. But, I am confused while implementing RAID 1 using 4 RAID disks. Can we use two disks for storage and two for mirroring using RAID 1? I couldn't find the way to create RAID disk using gparted tool in Ubuntu 10.04 Desktop version. Maybe, the desktop version doesn't support RAID. I am trying to implement RAID on the existing Ubuntu installation? I have added 4 X 2TB HDD in the system and I want RAID 1 to be implemented in these 4 drives with 2 drives for storage and 2 devices for mirroring. Any help would be appreciated. Thanks! Updated: I installed Ubuntu 12.04 LTS and followed the following tutorial and it works now: www.youtube.com/watch?v=z84oBqOxsD0

  Read the article

• Can't install SB750 RAID drivers in Windows 7 for two additional storage drives

  - by jf46

  Mobo: ASUS M4A79XTD, 790X/SB750 OS: Windows 7 x64 I currently have SATA 1-4 set to RAID and SATA 5-6 set to IDE. I have an SSD connected to SATA5 with Windows 7 installed on it, and that works fine. I also have configured a RAID 1 array of two 1TB HDDs, connected to SATA 1 and 2. These don't show up in Windows, and I'm having trouble getting the RAID driver installed. I even tried booting from the Windows DVD and repairing or installing Windows, but when I navigated to the relevant .sys files on my motherboard's driver CD, Windows setup told me that the files in question weren't relevant to my hardware. To be clear: I'm not trying to install Windows on a RAID. I have Windows installed on a separate disk on a separate SATA controller. I just want to get the SB750 RAID drivers installed so that the Windows disk utility can see my RAID 1 array, which is composed of two other disks. Do I need to wipe my SSD and reinstall Windows to get the RAID driver installed? That seems kind of ridiculous, and given what I described above, I'm not even sure it would work. Any help or guidance would be appreciated - thanks! Edit: Also, I've copied the driver files from the mobo CD into system32 and rebooted, no luck. Then I changed HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV\Start from 3 to 0, and that didn't work either.

  Read the article

• Raid-5 Performance per spindle scaling

  - by Bill N.

  So I am stuck in a corner, I have a storage project that is limited to 24 spindles, and requires heavy random Write (the corresponding read side is purely sequential). Needs every bit of space on my Drives, ~13TB total in a n-1 raid-5, and has to go fast, over 2GB/s sort of fast. The obvious answer is to use a Stripe/Concat (Raid-0/1), or better yet a raid-10 in place of the raid-5, but that is disallowed for reasons beyond my control. So I am here asking for help in getting a sub optimal configuration to be as good as it can be. The array built on direct attached SAS-2 10K rpm drives, backed by a ARECA 18xx series controller with 4GB of cache. 64k array stripes and an 4K stripe aligned XFS File system, with 24 Allocation groups (to avoid some of the penalty for being raid 5). The heart of my question is this: In the same setup with 6 spindles/AG's I see a near disk limited performance on the write, ~100MB/s per spindle, at 12 spindles I see that drop to ~80MB/s and at 24 ~60MB/s. I would expect that with a distributed parity and matched AG's, the performance should scale with the # of spindles, or be worse at small spindle counts, but this array is doing the opposite. What am I missing ? Should Raid-5 performance scale with # of spindles ? Many thanks for your answers and any ideas, input, or guidance. --Bill Edit: Improving RAID performance The other relevant thread I was able to find, discusses some of the same issues in the answers, though it still leaves me with out an answer on the performance scaling.

  Read the article

• Redhat Software RAID 1 not syncing

  - by hamstar

  Hey guys, I setup a software RAID 1 on a Redhat server, everything went sweet and it synced the first time. The other day the raid failedover for some reason and the disks hadn't been syncing since that first time, so it went back to 2 weeks ago when we did the first sync. We got the system back up running off the master only. However what would cause the software raid to not sync? I used mdadm to setup the RAID. Any ideas? EDIT: Sorry I don't have the output from /proc/mdstat before the raid failedover, it is now running on only the master... I can put the slave back in no problems but I was wondering how to make it sync all the time instead of only when I add it.

  Read the article

• Build a RAID-5 USB Array or NAS?

  - by TK Kocheran

  I'm looking to build a RAID-5 or RAID-6 hard disk array to be used as a centralized backup location for my home network. I have a lot of 4-8GB DVD ISO files which I intend to serve over the network to my TV using DLNA or something similar. I need decent write times, fast read times, and preferably a way to connect this array to my network router over USB. I'll probably be using ext3/4 on it (I'd use btrfs if my router supported it :-[). Is there a way to build a RAID array that is accessible over USB? I'm kind of new to this and most guides assume you're running a RAID array inside your machine. I need at least 5TB of space, and I need redundancy, so I prefer RAID-6. How can I go about accomplishing this?

  Read the article

• Reliable Linux RAID Card

  - by Chris S

  Can anyone recommend an appropriate RAID card for use under Linux (Ubuntu)? I have three Western Digital SATA drives, and would like to setup either RAID-1 or RAID-5. Software RAID has been very flakey and unreliable for me (e.g. it doesn't seem to mirror the boot partition). Unfortunately, most RAID cards I've seen online don't mention any Linux driver support. Would most cards work in Linux, or do I have to look at a select few that explicitly support Linux?

  Read the article

• RAID 1 not performing as expected

  - by Faken

  I recently bought a new 320Gb hard drive for my computer to set up RAID 1 on it for some added security. Installation went as smooth as could possibly be (plug in power, plug in data cable, start up computer, Intel software recognized new drive, right click create RAID 1, done!). However, for some inexplicable reason, I seem to have strange test results when using BENCH32. On my old configuration, a single 7200 rpm drive, I achieved about 60 MB/s write and 70 MB/s read. With a new RAID 1 configuration, I would expect the write to be slightly diminished but read to be significantly improved (though not exactly double speed). However, with the new configuration, I am getting 90 MB/s write and only about 80 MB/s read. I should NOT be getting improved write performance, especially NOT better than read! What's going on? My system setup is: q6600 2.4ghz CPU 4Gb DDR2 667mhz RAM on board Intel ICH9R "RAID chip" 2x Seagate 7200 RPM 320GB drives in RAID 1 Widows 7 home premium 64-bit

  Read the article

• Upgrade no raid server to raid

  - by AZee

  I have just learned that our PDC has a single drive with 2 partitions. I also know that this drive has bad blocks as recorded in the event log. What I would like to do is to convert this to a RAID solution with a nice balance between economy and performance. I will admit that I have only configured servers with RAID from scratch, and have no experience upgrading an existing system into a RAID system. In fact, I'm not sure it is even possible. Since this is the PDC for 350+ workstations downtime is important. I'd like to hear from other System Administators how they would tackle this and their recommendations for all devices. At this time it seems to me that I can replace the existing drive and then restore from backup or install a controller, drives, configure the RAID an basically start from scratch. Thank you for taking your time. ~AZee

  Read the article

• Does RAID negatively affect non-RAID devices?

  - by Django Reinhardt

  I am running Windows 8 on an SSD, and it's all running swimmingly, but I want to store documents on two HHDs (not SDDs) running under RAID 1. My motherboard has two SATA controllers, both set to AHCI. On the 3GB/s controller, all four ports are used (1 Bluray Optical Drive, 1 Spare HD, and the 2 I wish to turn into a RAID 1 drive). Windows is on the 6GB/s controller. Like so: So my question is: If I turn these four ports (on the 3GB/s controller) into a RAID controller, will that negatively affect the non-RAID hardware plugged into it? I.e. Will the HDD or Bluray drive be slower/incompatible with being plugged into a non-AHCI controller? Thanks.

  Read the article

• Ubuntu 10.04 - Add RAID 1 Array?

  - by N Rahl

  I have an existing Ubuntu 10.04 desktop system setup and running on a hard drive (Drive A). I'd like to add 2 more hard drives (Drives B & C, same size) to the system and mount them as a RAID 1 array. How do I do that? I know how to create RAID arrays during the installation, but I don't want to reinstall my system, and I shouldn't have to since my system files will stay on their own drive separate from the RAID array. I've physically added both drives to the system, and formatted them as EXT3 with gparted. Ubuntu's disk utility has a "create raid" option, but it won't let me select any of my drives (it thinks they're all full). I don't mind using mdadm, but I've found several guides that are old, and give conflicting advice. Some say I have to edit an /etc/raidtab file, some say this is done automatically. So what's the current (Ubuntu 10.04) preferred way of adding a RAID 1 to an existing system? It should turn into a raid at boot, and mount itself in /home/myname/files/. Thanks!

  Read the article

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• Ubuntu 12.04 installation on GPT + RAID going into grub rescue

  - by Proy

  I have two 2TB disks. I am installing Ubuntu 12.04 using the alternate version of the server cd. On the partitioning page I have done my partitioning as follows /dev/sda1 - 32 MB - bios_grub /dev/sda2 - 50 GB -raid device /dev/sda3 - 8 GB -raid device /dev/sda4 - Balance full GB - raid device /dev/sdb1 - 32 MB - bios_grub /dev/sdb2 - 50 GB -raid device /dev/sdb3 - 8 GB -raid device /dev/sdb4 - Balance full GB - raid device After this I have setup raid devices /dev/md0 for /(/dev/sda2 + /dev/sdb2) for / ext4 /dev/md1 for swap( /dev/sda3 + /dev/sdb3)for swap /dev/md2 for /home(/dev/sda4 + /dev/sdb4)for /home ext4 The installation finishes it shows that it is installing grub to /dev/sda and /dev/sdb. But once the system reboots it falls into grub rescue mode. on doing ls I can not see the md devices only hd once. I also tried booting into rescue mode with the install cd and doing grub-install /dev/sda and /dev/sdb. What am I doing wrong ? Why is grub2 not detecting the raid revices ? UPDATE: I just did the same steps with Ubuntu 10.04 and it worked perfectly fine. I wiped out the RAID and partitions and everything and did it from scratch. I think the issue is with Ubuntu 12.04 and the way it partitions 2 TB disks

  Read the article

• Swapping 3Ware Raid Card - Best Procedure

  - by Brian Lee Jackson

  We have a server running an old firmware version and driver (just took this position) on the 3Ware 9650SE Raid Controller... We have been having issues with the server and seemed to have narrowed it down to the Raid Card... I will be replacing the Raid card with the same model of 3Ware 9650SE, however, the card ordered most likely will have newer firmware on it. I managed to backup all the data to a very large drive. My plan is to update the firmware/driver on the current setup (which is still booting) and verify that everything works.. Then throw in the new Raid Card, check the firmware version (not letting it post). And update to newest firmware if needed via Java management utility on the card? Is this the best route? Thanks!

  Read the article

• Does growing a RAID 5 destroy the data on the RAID?

  - by Ellis

  For a linux software RAID using madadm, does adding a harddrive and growing onto the RAID, destroy the data that's already on the RAID or does it preserve everything?

  Read the article

• Software mirroring (RAID1) versus "Fake Raid" for new Windows 7 install

  - by kquinn

  I've just ordered two new hard drives for my main desktop and a copy of Windows 7 Professional 64-bit. I'd like to do a clean install of Win7 onto the new drives (leaving my old XP Pro boot partition around for a while in case something goes disastrously wrong, etc.). I want to have them set up in mirrored (RAID-1) mode. My understanding is that Win7 Pro can do software mirroring, but can I set this up directly at install time? If so, how? Note that I'd like the disk to be split into three partitions (OS/Apps&Data/Bulk data), all of which should be mirrored. Would it be better (more reliable or faster) to use my motherboard's hardware RAID support? My motherboard is an older nVidia nForce 680i SLI, which is not the most stable of motherboards, and I'm not sure how trustworthy its RAID1 configuration might be (or if Win7 could even detect and install onto a hardware-mirrored volume). Also, the performance characteristics of RAID1 are rather different than RAID0 or RAID5, and I'm wondering if Win7's software mirroring might actually be faster than hardware RAID1 (for example, I'm more of a Unix admin when I have to wear the sysadmin hat, and I've had great success deploying ZFS; most hardware RAID1 implementations have to read both disks and compare results to look for data errors, but ZFS can read from only one disk in the mirror and just use the built-in checksum, meaning it can have up to 2x the number of reads in-flight, as long as there's no data corruption). Edit: Okay, my question about whether Windows 7 can do software mirroring has been answered, and it can. I'm still unsure whether Windows software RAID or my motherboard's hardware "fake RAID" function is a better choice, though. Remember, I'm only interested in mirroring -- not the more complicated striping or parity operations that generally show the poor performance of crappy motherboard RAID solutions.

  Read the article

• Re-Initialize RAID-0 in software after card failure

  - by Ben

  I'm working on a Friend's WD MyBook "1TB" HDD that is not mounting. When I got in to it, I discovered that it is really 2 500GB HDD's set up as RAID-0. It appears that the drives themselves are fine, but that the logic board has failed. My questions is this: can I re-initialize the RAID-0 using software RAID so that I can recover the data to another drive? If so, how and which software RAID would be best (Preferably open source. any platform OK).

  Read the article

• How to interrupt software raid resync?

  - by Adam5

  I want to interrupt a running resync operation on a debian squeeze software raid. (This is the regular scheduled compare resync. The raid array is still clean in such a case. Do not confuse this with a rebuild after a disk failed and was replaced.) How to stop this scheduled resync operation while it is running? Another raid array is "resync pending", because they all get checked on the same day (sunday night) one after another. I want a complete stop of this sunday night resyncing. [Edit: sudo kill -9 1010 doesn't stop it, 1010 is the PID of the md2_resync process] I would also like to know how I can control the intervals between resyncs and the remainig time till the next one. [Edit2: What I did now was to make the resync go very slow, so it does not disturb anymore: sudo sysctl -w dev.raid.speed_limit_max=1000 taken from http://www.cyberciti.biz/tips/linux-raid-increase-resync-rebuild-speed.html During the night I will set it back to a high value, so the resync can terminate. This workaround is fine for most situations, nonetheless it would be interesting to know if what I asked is possible. For example it does not seem to be possible to grow an array, while it is resyncing or resyncing "pending"]

  Read the article

• How do I reinitialise a failed RAID 5 drive using terminal on Ubuntu Server

  - by Stephen

  I've currently put together a new system and part of that has been creating a software RAID 5 using 'mdadm' in Ubuntu Server. I successfully got to the point where I create the array using: sudo mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 I left it to do its thing overnight then used the following command to check on it: watch cat /proc/mdstat To which the following was returned: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[4](S) sdc1[2] sdb1[1] sda1[0](F) 5860535808 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/2] [_UU_] unused devices: <none> It appears that one has failed (and I'm not too savvy with why another is a spare). So, just to be sure that something else isn't amiss I wanted to try and re-engage the failed drive. Can someone explain how I can do that and what I should do with the spare (if anything). And also how do I know when synchronisation is complete? The tutorial I used to get this far is located here: http://sonniesedge.co.uk/2009/06/13/software-raid-5-on-ubuntu-904/ Many thanks! p.s. Here is some extra information that may help: sudo mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Mon Jun 18 21:14:21 2012 Raid Level : raid5 Array Size : 5860535808 (5589.04 GiB 6001.19 GB) Used Dev Size : 1953511936 (1863.01 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon Jun 18 21:50:26 2012 State : clean, FAILED Active Devices : 2 Working Devices : 3 Failed Devices : 1 Spare Devices : 1 Layout : left-symmetric Chunk Size : 512K Name : myraidbox:0 (local to host myraidbox) UUID : a269ee94:a161600c:fb1665e7:bd2f27b3 Events : 13 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 3 0 0 3 removed 0 8 1 - faulty spare /dev/sda1 4 8 49 - spare /dev/sdd1

  Read the article

• Raid recovery in gigabyte GA-8I945 Pro

  - by epeleg

  This was a working machine until a few days ago. And now it won't boot into the OS, during startup if makes clicking sounds (I think from one of the drives). Installed OS: Windows 2003 Web edition Hardware: Gigabyte GA-8I945P Pro , 2*160G Sata in RAID1 configuration , 2 Volumes – 25G and the rest. When I installed windows on it, during setup, I pressed F6 and used ICH7DH drivers of RAID. The manual for the MOBO says: Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. But the machine never shows this message. BIOS SATA RAID/AHCI Mode is set to RAID. Any ideas or pointers on what I can do to recover my data? Thanks

  Read the article

• RAID level hard drives?

  - by JT

  Hi All My Motherboard has 4 internal SATA ports. I am considering a linux software raid. I plan to use this for backing up my work movies, music etc Do I need to spend the money on RAID Level drives? Or am I safe with standard hard drives? a 2TB Hitatchi 7200 is like $89 at NewEgg where a Samsung F1 RAID 1tb is $150.00 Thoughts?

  Read the article

• Software for RAID Failure Alerts?

  - by QF_Developer

  I have two 256 GB Samsung 840 Pro SSD disks in a RAID 1 array. I would like to receive a notification if one of the disks in the array fails. Can anybody recommend an application I can install on the server to fire an email if such an event occurs? Here are some additional specs: Supermicro X9SCM-IIF motherboard utilising the hardware RAID controller. OS = Windows 2012 Standard Also is it possible to simulate a disk failure by pulling it out of the bay? SSDs appear to fail close together when in a mirrored config so I'd like to know ASAP if one goes down so I can swap them out with minimum delay. UPDATE 26th June 2013 ------------------------ None of the software that ships with the Supermicro X9SCM-* motherboards offer support for RAID monitoring. As has been pointed out here, these boards are built on an Intel chipset for RAID and so I installed Intel Rapid Storage Technology that supports automated email notifications on RAID failure http://www.intel.com/support/chipsets/imsm/sb/cs-020784.htm One small issue, the software only allows you to send email notifications without SMTP authentication. There's a bunch of different workarounds here: http://communities.intel.com/thread/30771

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >